AS5400 IP fall back routing without Call Manager

Hi guys
my system is using AS5400+SLT+PGW, but without call manager.so i guess i have limited functions of Cisco voip, but so far all is well
my question is:
how can i do IP fall back routing to the same destination, with 2 target IPs.lets say my destination with 2 target IP1:192.168.1.1 and IP2:192.168.1.2
primary IP is 1.1 and is in dial-peer 1
calls will be sent via dial-peer 1.
in the event of IP1 fail, how can IP2 will take over as the new primary target?
and when IP1 back to service, it will re route backt to IP1
came across of using dial-preference, but not sure how it works and if it fits my scenario
currently , just pointing to IP1.dont have IP2 configured anywhere.and the only fall-back routing i have now is frm my PSTN switch (which is different frm IP switches)
thanks in advance
brendan

Brendan,
Use preference command under dial peers.
dial-peer voice 1 voip
preference 0 (default)
session target ipv4:
dial-peer voice 2 voip
preference 1 (lower priority)
session target ipv4:
HTH
Sankar
PS: please remember to rate posts!

Similar Messages

Af:Table data refresh without calling ManagedBean constructor

Hi,
I have an adf application jspx page where I have af:selectOneChoice and af:table showing default data. On selecting af:selectOneChoice value (assigned, completed etc.) I am calling managed bean method which calls task flow client api which gets the task details based on af:selectOneChoice value and show in the adf table.
When ever I change the af:selectOneChoice value, first it is callling 'valueChanged(ValueChangeEvent valueChangeEvent)' method in managed bean and able to get the records based on filter value(Example: Assigned). Issue is immediatly after that Managed bean constructor also calling which overrides the previous query and get the records based on default filter value (Example: All).
here is <af:selectOneChoice & <af:table code:
<af:selectOneChoice id="rsoc" autoSubmit="true"
binding="#{backingBeanScope.backing_taskdetails.rsoc}"
label="Status" valueChangeListener="#{backingBeanScope.backing_taskdetails.valueChanged}">
<f:selectItem itemValue="A" itemLabel="All" />
<f:selectItem itemValue="AG" itemLabel="Assigned" />
<f:selectItem itemValue="C" itemLabel="Completed" />
</af:selectOneChoice>
<af:table emptyText="#{bindings.taskList.viewable ? 'No data to display.' : 'Access Denied.'}"
var="row" columnStretching="multiple"
value="#{backingBeanScope.backing_taskdetails.taskList}"
immediate="false" rowSelection="single"
binding="#{backingBeanScope.backing_taskdetails.t1}"
id="t1"
inlineStyle="font-family:Arial, Helvetica, sans-serif; border:0pt none; "
partialTriggers="::rsoc">
Here partialTriggers is invoking managed bean. So Can I refresh only table data without calling managed bean constructor on selection of <af:selectOneChoice?
Any inputs will be highly appreciated. Thanks.

Hi,
Thanks for your reply.
here it is my adfc-config.xml file.
<?xml version="1.0" encoding="UTF-8" ?>
<adfc-config xmlns="http://xmlns.oracle.com/adf/controller" version="1.2">
<managed-bean id="__2">
<managed-bean-name id="__3">backing_test</managed-bean-name>
<managed-bean-class id="__4">view.backing.Test</managed-bean-class>
<managed-bean-scope id="__1">backingBean</managed-bean-scope>

</managed-bean>
</adfc-config>
I am not using adf taskflow (Should I use this, I am not sure as I am new to ADF. Please suggest). My execution flow is I have 'Human Task SOA application' which I am calling from adf application (managed bean --> workflow cllient API --> Human Task SOA Application) and showing task details in cutom UI screens. I do not want to use BPM worklist application as I need my own screens.
thanks.

SRM7 WF Fall Back Agents

I would like to configure the fall back agents for the 'Manager of Manager' shopping cart approval process to be the originating users manager. Not all departments in our organization have multiple levels of management but we would still like a second level of approval when the shopping cart amount is greater than 50K. It works when there are multiple managers defined in the org structure, but I get an Agent Determination error when there is only one manager defined.
Is there a quick way to do this?
Thanks
Jon

Saravanan,
I figured out how to get it to determine the originators first level manager and direct the work item there.
The business requirement is for carts over $50K there needs to be a director level approval. In most cases in our organization, the director is the second level manager so the manager of manager agent determination process works perfect. However some departments have one manager/director and only three employees so there is no organizational second level of approval that can be used. In these cases, the manager is the director and needs to approve the cart twice. Using the fall back agent method seems the best approach for these occurances.
Jon.

What is call manager doing with Jabber guest if you have no endpoints registered to Call manager?

Our Call Manager deployment is in it's VERY early stages. We have a Telepresence infrastructure at the moment (VCS Control and Expressway). All of our TP endpoints and Jabber Telepresence clients are registered to the VCS. What is going on that the Jabber guest and VCS server need call manager for? I know it's REQUIRED in the manual and I saw a slide somewhere that said using Jabber Guest without Call manager is NOT SUPPORTED.
Realistically though, I might not get permission to build a SIP trunk between the new Call manager and VCS for some time..so...supported or not will it work without call manager or is there something going on that's critical on call manager to make it work regardless of the fact that there is nothing registered to CUCM?
thanks!

Hi Douglas,
As you've gathered this configuration is not supported, and hence we don't actively test it or document it. That said, it should work fine
Mike

E71 backup SMS,Advanced call manager, Office probl...

Hi
I updated my Nokia E71, before updating I took a back up of my phone. After updating software when I restored back up Advanced called manager is not being installed it says certificate is experied, SMS messages are not being restored, Office is not working..... please advice how to get it working ?
Regards
Solved!
Go to Solution.

Dear
Welcome to the forum and thanks for your recent post.
You can backup your data and content but not for the program itself. Re-install the application and then restore the data/content.
It should be noted that some applications require a lincence and have trial period that must have been expired.
Please contact your local careline.
You'll need your IMEI number product code and they will set your license with you.
Both items can be obtain by typing (*#06#) from your device home screen.
Do let us know if you require further assistance.
Sincerely
Carl
If this post answers your question, you can help others by clicking the green accepted solution' button.
Please ask your questions to the main board and not to my mailbox. Thank you.

Fn and function keys config falls back to "default"

Hello, I own Thinkpad E531 laptop with Windows 10 and the problem I have is that after restart the configuration falls back to so-called "default" instead of staying on legacy mode.Any ideas what may cause this problem? (Perhaps Windows 10 was a bad idea, since it apparently favours its default settings very much.)

Open System Preferences, go to the Keyboard & Mouse panel, and check the box "Use the F1-F12 keys to control software features".

How to call a Javascript function from backing bean without any event

Hi,
Someone knows how to call a Javascript function from backing bean without any event ?
thanks

Please review the following thread:
ADF Faces call javascript
Luis.

Can this router fall back to 3g if 4g is not available?

We recently purchased this router to work remotely. However some of the places we are at have only 3G service. Phone seem to work with 3G receiving data, but our 4G LTE router will not connect. I've looked through the setting in the router, but can't seem to find anyway to have it fall back to 3G if 4G isn't available.

The VZW 4G LTE router does not appear to have tie-ins to the old GSM (3G Only) network. It may be able to fall back to 3G while connected to the new SIM card network, but there are no ways to control this behavior from the User Guide.
If you are only within range of a 3G only signal then I would not expect this device to work. The silver lining here is that 4G LTE is supposed to replace the entire 3G Verizon footprint. Eventually anywhere that you have 3G only service will have a 4G LTE signal and your router will be able to work.
If you need an immediate solution from VZW it would have to be to swap the 4G LTE router and go with a Mobile Hotspot instead since they can connect to 3G only at this time.

How do I Translation Route a call back into CVP?

This is ICM 8.5, CVP 8.5 and Avaya CM 5.2. I'm trying to configure the system to be able to Translation Route a call back into CVP that originally started in CVP. I've read and read Cisco documentation that talk about various ways it can be done but I think I really need step-by-step instructions to figure out what I've done wrong. I'm happy to explain it in gory details if anyone wants to help me troubleshoot. However, I think it would be simpler if someone can point me to a document that outlines a successful configuration and I can find my own mistake.

Thanks clearbluelou, some of this was very helpful, but I had to set my translation routes up differently. Kris Lambrecht's post was very helpful, but also introduced some confusion, which looking back was very simple...hindsight is always that way right?!?!
I am going to list out the configurations I used to make this work, most of which are what's listed in the Type
8 setup in Kris's post starting with Step 7 except its for a Type 10 Network VRU; you don't use Type 8 anywhere, but the configuration is very similar.
Assumption is that you already have an existing system and are routing calls to CVP already so a lot of the steps in the config guide are already done.
References below are to "Configuration and Administration Guide for Cisco Unified Customer Voice Portal Release 8.5(1)" starting on page 109, step 7:
http://www.cisco.com/en/US/docs/voice_ip_comm/cust_contact/contact_center/customer_voice_portal/cvp8_5/configuration/guide/ConfigAdminGuide_8.5.pdf
Here's the details of my implementation:
ICM 7.2.7
CVP H323, Type 10
Avaya PBX connected with a PG also running CTIOS
Destination is the CVP Servers/CVP PGs (PG1), call transfer is originating from an Avaya PBX connected to ICM via a PG/CTIOS server (PG2).
1. Build a new Service under destination PG, CVP in this case, as outlined in Step 7 from the CVP Config Guide.
- Service
Peripheral Number: 2
Peripheral Name: Pre_Route
Name: CVP_PG1.Pre_Route
- Route
Name: CVP_PG1.Pre_Route
-Peripheral Target
Not required
Labels
Not Required
2. Build Network Trunk Groups, as outlined in Step 8 from the CVP Config Guide:
- Network Trunk Group
Name: CVP1_NTG
Peripheral: CVP_PG1
PeripheralNumber: 200
PeripheralName: CVP1_NTG
Name: CVP_PG1.CVP_NTG
Trunk Count: Use Trunk Data
3. Build Translation Routes using the TransRoute wizard, I built a pool of 10 DNIS 1000-1010; these are dummy DNIS; outlined in Step 9 from CVP Config Guide; here's what they should look like in
the TransRoute explorer when finished:
-Translation Route
Name: TR2CVP1
Type: DNIS
-Route
Name: CVP1.1 - CVP1.10
Service Name: CVP_PG1.Pre_Route
-Peripheral Target
DNIS's: 1000-1010
NTG: CVP1_NTG
-Label
Routing Client: PBX_PG2
Labels: 1000-1010
Label Type: Normal
Customer: None
4. Configure Trans Route DNs 1000-1010:
- Have to be built on the Avaya pointed to a VOIP gateway with Session Target equal to the CVP Call Server (or GK).
- Add Translation Route DNISs in CVP Call Server Configuration under ICM Tab.
!!!Make sure you "Save and Deploy"!!!---->If you don't calls will show up on the ICM as new calls on the Translation
Route DNIS's under your CVP Peripheral.
5. Build Dialed Numbers in ICM:
-Extension 2000 is the dialed number Agents on the Avaya transfer to.
-VDN 2000 on Avaya PBX should be routed to an Adjunct Route step which will send a route request to PG2 and kick off a script in ICM.
-You have to build a dialed number in ICM Dialed Number Explorer under the PBX peripheral (PG2 in my example) PG2.2000, and point it to a CallType and subsequently a script, for example "Avaya2CVP".
6. Build your ICM Call Routing Script: (follow's ClearBlueLou's description)
- Route the call through typical CVP call setup initialization nodes
-Route to Trans Route to VRU node with "CVP_PG1.Pre_Route" as the service selected, and "TR2CVP1" Trans Routes
selected.
-Then send to a microapp.
Your test call should have exited the success connection of the TrasRoute to VRU node and will continue routing with all call variable information will route (and show up in TCDs and RCDs) under Dialed Number PG2.2000.

HT1766 I deleted some phone records (call numbers, dates) & texts. Can I access them from back-up without restoring the phone. Don't want to alter what I have, just find what I later deleted

I deleted some phone records (call numbers, dates) & texts. Can I access them from back-up without restoring the phone. Don't want to alter what I have, just find what I later deleted

Without "pretending" to be yourself on the other phone (change settings) there's nothing else you can do.
iOS devices are meant to be single user and can't view iCloud.com the same way a Mac or PC can do.
You need to find a desktop or laptop machine (Mac or PC) to log in at iCloud.

Do I get full conference call management options on iPhone 6 model A1549 if using it with GSM carriers?

I have iPhone 6 model A1549, bought from and currently using with Verizon. You all must be aware that we can use the same phone for GSM carriers like at&t as well. Now we all know that some of the features related to conference calling are not available on CDMA carriers, like we cant have more than 2 callers, and we can't manage conference calls by making the conversation with one party private for some time and again switching back to conference mode, disconnecting a particular party instead of having to end the entire call etc. reference link- iPhone: Understanding phone features - Apple Support These features are available on GSM models and carriers, I just wanted to ask if I use a GSM SIM from a GSM carrier on this model, do I get these additional conference call management options or I am restricted to Verizon like experience while being on at&t (and while using the at&t SIM in this model)

Yes, I am dealing with this right now on at&t with a 6 plus. I've been down the same road as you. I got it to work with a windows phone yesterday but not my 6 plus when I switched back to the iPhone. My wifes 6 works fine. I believe it is an at&t issue and not an 8.3 issue. After dealing through several levels of support at at&t, they are telling me it has to do with their transition to hd voice. Some people are having this issue because they are updating their system and some peoples phone profile, on phones that have hd voice capabilities, are not getting added to their line and call forwarding will not work without it. I have a trouble ticket open to their engineering dept and they promise it will work for me on or before the 24th of april. Engineering has to build my phones profile so call forwarding will work with my iPhone.
This is frustrating because like you, I need to forward my calls because I have no signal in my office and need to forward to another phone so I can get my calls. If at&t would quit dragging their feet and enable wifi calling, this wouldn't be an issue for me. I would suggest you put more pressure on at&t and escalate this until it gets resolved. Or put your sim in a phone that does not have hd voice capability and see if it works then.
Good luck. I'm keeping my fingers crossed this will be fixed for me on or before the 24th. We'll see.
EDIT: I see you did put it in another phone and it worked. That backs up that the issue is at&t and their hd voice upgrades. They had no explanation as to why some work and some don't, but have them make sure a profile for your phone is on the line. If not, they'll need to build one for the phone so that it''l work. At least that's the story for now. Like I said, I'll know more in a day or two.

Cisco ip phone 7960 cannot connect to call manager express

The 7960 ip phone seems not to connect to the call manager express
router and i have already put the firmware and configured the tftp
server,the rest of the phones the 7911`s are all working ok,i have tried
to reset the phone but it doesnt respond to the # key so as to reset to
factory defaults.
I have tried all the options of resetting it but to no avail.
could someone give me some techie tips on this ? could it be a hardware issue ?? please assist.

Go to the phone and check if the TFTP server is correct (should be the CME IP address). Also check the DHCP address.
Resetting 7900 Series IP Phones to Factory Defaults:
http://www.cisco.com/en/US/products/hw/phones/ps379/products_tech_note09186a00800941bb.shtml
Check the bug:
CSCed93627: Not able to reset 7970 back to factory defaults

Fall Back

Hello ,
Is is possible to configure fall back link on the router if any one site goes down. Please let me know the steps to configure.
Thanks
Abhishek

Here is the SRST guide for you.
http://www.cisco.com/en/US/docs/voice_ip_comm/cusrst/admin/srst/configuration/guide/srst41/srst41sa.html
Basically, you need to configure CUCM for this site (SRST)
Apply the SRST Site to the Device Pool
Configure the router for SRST
Reboot the phones so they are aware of the new SRST router
Setup the dial peer you want to use for dialing inbound or outbound or both. Simply using 9T usually is fine for outbound, prioritize 911 and9911 of course
Inbound, you will need to normalize or strip digits if you have 4 digits extensions, otherwise when the call comes inbound, its 10 digits and the router will not know what to do with it.
Voicemail rollover is complicated and sometimes not needed
Remember, SRST fallback and then re-registration to CUCM takes a few minutes. Its not immediate. So be patient in your testing until you are familiar with SRST
Good luck!

PLAR on Call Manager

I'm attempting to set up a direct PLAR to a line appearance on 79XX sets. I would like to have the FXO ring the line appearance, (I get this piece working)but I'm unable to access the line on the 7960 in this case and draw dialtone from the FXO. I would like to go directly to the FXO without the need for a dial pattern. Is there a way to achieve these results on Call Manager? I'm running 4.13(es94)version 4.1(0.11) Any help thoughts accepted and appreciated.

The FXO trunk line functionality is availabe with Callmanger Express, but not with Callmanager. You can give the appearance of this functionality by doing the following.
1. Create a speeddial on the phone of 9.
2. Go to Callmanager service parameters and change the Speed Dial Await Further Digits parameter to True.
Now the user can begin dialing the number when they choose this "line". Of course the route patterns will still have to be in place, but it gives the appearance of seizing a line.
Hope this helps. If so, please rate the post.
Brandon

Hunt Group with Pots lines in Call Manager

Hello all. I have a site with 12 Pots lines. It is all configured via Call Manager. We are using mgcp. I asked the telco to setup the numbers to hunt which they said they did but still when I call the main number second time it just rings and eventually get some voicemail that is not from the call manager. I think I need to setup Hunting in the Call Manager? Is that correct?
Line Group --> Add the extensions in here and set them up to hunt?
Hunt List --> Create a Hunt list and associate a Line Group with it?
Hunt Pilot --> I add all the extensions in here?

Let's take one step back. What are you trying to accomplish? I am assuming you want to market one number but have the ability to accept multiple calls on that number. If that is the case, having the telco set up a hunt is the way to go.
Beyond that, where do you want those calls from the PSTN to route? Are you wanting those calls to ring a hunt group on your side? If so, you will need to do the following:
     1. Configure a Line group. (Call Routing -> Route/Hunt -> Line Group) This is where you will be adding the extensions. You will also need to specify a distribution algorithm. The distribution algorith, is where you will be choosing how you want the extensions to ring. For instance, if you set the DA to broadcast, every extension in the line group will ring at the same time. Click Help --> this page, while you are in the line group configuration page to get more information about the settings you can modify and different algorithms you can use.
     2. Configure a Hunt List. (Call Routing -> Route/Hunt -> Hunt List) You will need to create a new Hunt List and add your line group to it. The hunt list is evaluated in a top down fashion. You can get pretty tricky with multiple line groups with different distribution algorithms in your hunt list, but if you just want something basic,just add the line group you made.
     3. Configure the Hunt Pilot. (Call Routing -> Route/Hunt -> Hunt Pilot) The hunt pilot will be the dialed number that triggers the hunt group. Make sure you select all the required settings. You will be selecting the hunt list you just made in this configuration page. Be sure to set a maximum hunt timer and final destination so that the calls do not just ring forever. You can get pretty granular with the settings in here. Reference the help --> this page document for more information.
     4. POINT THE FXO PORTS TO THE HUNT PILOT. This is very important. Calls to your analog lines will not trigger the hunt group unless you point the ports to the Hunt Pilot. If you are using MGCP/SCCP you will need to enter the hunt pilot in the "Attendant DN" field for EVERY FXO port. If you do not enter a value here, CUCM will have no idea what to do when the port rings. It will not answer the call if there is no value specified. This would explain why your calls were ending up with the telco voicemail service; CUCM was never answering the call.
If you completed the above steps correctly, you should be able to call the main number multiple times and have the calls go to a hunt group on your side, no matter which line the call ends up coming in on.
Let me know if you have any questions, this can be kind of tricky at first.
PS, if the calls were going to a voicemail that wasn't from Call Manager (Unity Connection) call the telco and have them remove voicemail service from the lines, assuming you have configured Unity Connection to handle that.
Hope this helps,
Dallan

AS5400 IP fall back routing without Call Manager

Similar Messages

Maybe you are looking for