ASA5520 SNMP temperature monitoring

Hi!
I would like to know if it possible to obtain ASA temperature values (chassis, CPU, etc) with SNMP.
If yes, is there a specific OID?
I'm on 8.2(5) release
Thanks

I doublechecked - I believe it's only the 5580 and 5585 (and possibly 5545-X and 5555-X). that display it in ASDM. It doesn't specifically mention SNMP but see the reference here where the information is described as available on those platforms.
Also see here where the "show environment" command description states:
You can display operating environment information on the ASA 5545-X, 5555-X, 5580 and 5585-X. This information includes the operational status of the fans and power supplies, and temperature and status of the CPUs and chassis.
The same platforms are listed in the 9.1 command reference. However I just checked on a 5525X running 9.1 and see:
# sh inv | i Chassis
Name: "Chassis", DESCR: "ASA 5525-X with SW, 8 GE Data, 1 GE Mgmt, AC"
# sh env temp
Temperature:
   Processors:
   Processor 1: 63.0 C - OK
   Chassis:
   Ambient 1: 43.0 C - OK (Chassis Back Temperature)
   Ambient 2: 33.0 C - OK (Chassis Front Temperature)
   Ambient 3: 41.0 C - OK (Chassis Back Left Temperature)
So I think it is all of the X series as I originally replied. That includes being able to see the temperatures in both ASDM and from command line.
I did check a 5550 (running 8.4) and the "show environment" command is not supported.
# show inv | i Chassis
Name: "Chassis", DESCR: "ASA 5550 Adaptive Security Appliance"
# sh env
               ^
ERROR: % Invalid input detected at '^' marker.

Similar Messages

1130AG temperature monitoring (SNMP / MIB)

Hi
Im trying to get some SNMP monitoring running for multiple 1130AG APs. I keep running into walls though. APS are running with the following image : c1130-k9w7-mx.124-25d.JA1.
Problem 1.
I cant use the show environment cmd on the APs. According to the following official Cisco document, the show environment cmd is supported from image version 12.2(11) JA , but is not available on my APs running 12.4(25d)JA1:
http://www.csd.uoc.gr/~hy435/material/cr12425d.pdf
Problem 2.
According to the Cisco IOS MIB locator, the 1130AG AP does not support the ENVMON-MIB . That MIB is generally used for temperatur monitoring on many cisco devices. The 1130AG does however support ENTITY-MIB , but I am not entirely sure that this MIB can return temp info. There is very little/no documentation on this.
Can anyone help me out? I would very much appreciate it :)
\Christian

Hi
Im trying to get some SNMP monitoring running for multiple 1130AG APs. I keep running into walls though. APS are running with the following image : c1130-k9w7-mx.124-25d.JA1.
Problem 1.
I cant use the show environment cmd on the APs. According to the following official Cisco document, the show environment cmd is supported from image version 12.2(11) JA , but is not available on my APs running 12.4(25d)JA1:
http://www.csd.uoc.gr/~hy435/material/cr12425d.pdf
Problem 2.
According to the Cisco IOS MIB locator, the 1130AG AP does not support the ENVMON-MIB . That MIB is generally used for temperatur monitoring on many cisco devices. The 1130AG does however support ENTITY-MIB , but I am not entirely sure that this MIB can return temp info. There is very little/no documentation on this.
Can anyone help me out? I would very much appreciate it :)
\Christian

SNMP Probe monitor query

Hi ,
I have created SNMP Probe based monitor to check the Total RAM free on certain Network devices.
I have total 16GB RAM space and i want to alert if lesser than 3 GB of Total RAM. I had configured /DataItem/SnmpVarBinds/SnmpVarBind[1]/Value lesser than 3467826 to be critical and alert. The other condition is /DataItem/SnmpVarBinds/SnmpVarBind[1]/Value
greater than 3467826 to be healthy.
Once configured i am getting alerts for higher values like 19458676. could someone please help me with this scenario and correct me if i am wrong.
Jesty Sam

Why you use SNMP to monitor RAM, you can create custom monitor for RAM between 2 value min. and Max.
SNMP is the most commonly used method mainly because it is easy to set up and requires minimal bandwidth and CPU cycles. If your network devices support SNMP and/or if you want to monitor large networks with several hundred or thousands of sensors, we recommend
you to start with SNMP. Besides network usage monitoring, another well-known feature of SNMP is the ability to also watch other network parameters such as CPU load, disk usage, temperature, as well as monitoring many other readings, depending on the queried
device.
Please remember, if you see a post that helped you please click "Vote As Helpful" and if it answered your question, please click "Mark As Answer"Mai Ali | My blog:
Technical | Twitter:
Mai Ali

Creating SNMP Trap Monitors in 2012 R2

Hello,
For the past week or so I have been attempting to create a MP for my company's UPSs to be monitored in SCOM 2012 R2. I have created a custom MP with custom datasources and objects. All seems to go according to the plan until I attempt to create a SNMP
Trap monitor for those objects. I am able to verify that the device is discovered and is sending the traps successfully with a view. The problem seems to lie within the setup of the monitor. I have followed the steps as much as I can from this page http://technet.microsoft.com/en-us/library/hh563870.aspx
to create a monitor that will be triggered by an incoming trap saying the UPS is on Battery Power.
This is the initial or trigger event information received by SCOM:
<EventData>
<DataItem type="System.SnmpData" time="2014-07-03T08:48:07.6990732-07:00" sourceHealthServiceId="26DF02E5-DEA0-BED0-443B-3605A05D4790">
<Source>10.51.85.40</Source>
<Destination>127.0.0.1</Destination>
<ErrorCode>1</ErrorCode>
<Version>1</Version>
<SnmpVarBinds>
<SnmpVarBind>
<OID>.1.3.6.1.2.1.1.3.0</OID>
<Syntax>67</Syntax>
<Value VariantType="19">17567220</Value>
</SnmpVarBind>
<SnmpVarBind>
<OID>.1.3.6.1.6.3.1.1.4.1.0</OID>
<Syntax>6</Syntax>
<Value VariantType="8">.1.3.6.1.4.1.318.0.5</Value>
</SnmpVarBind>
<SnmpVarBind>
<OID>.1.3.6.1.4.1.318.2.3.3.0</OID>
<Syntax>4</Syntax>
<Value VariantType="8">UPS: On battery power in response to an input power problem.</Value>
</SnmpVarBind>
<SnmpVarBind>
<OID>.1.3.6.1.6.3.1.1.4.3.0</OID>
<Syntax>6</Syntax>
<Value VariantType="8">.1.3.6.1.4.1.318</Value>
</SnmpVarBind>
</SnmpVarBinds>
</DataItem>
</EventData>
This is the event should signal that everything is operating normally once again.
<EventData>
<DataItem type="System.SnmpData" time="2014-07-03T08:48:12.9133769-07:00" sourceHealthServiceId="26DF02E5-DEA0-BED0-443B-3605A05D4790"><Source>10.51.85.40</Source>
<Destination>127.0.0.1</Destination>
<ErrorCode>1</ErrorCode>
<Version>1</Version>
<SnmpVarBinds>
<SnmpVarBind>
<OID>.1.3.6.1.2.1.1.3.0</OID>
<Syntax>67</Syntax>
<Value VariantType="19">17567730</Value>
</SnmpVarBind>
<SnmpVarBind>
<OID>.1.3.6.1.6.3.1.1.4.1.0</OID>
<Syntax>6</Syntax>
<Value VariantType="8">.1.3.6.1.4.1.318.0.9</Value>
</SnmpVarBind>
<SnmpVarBind>
<OID>.1.3.6.1.4.1.318.2.3.3.0</OID>
<Syntax>4</Syntax>
<Value VariantType="8">UPS: No longer on battery power.</Value>
</SnmpVarBind>
<SnmpVarBind>
<OID>.1.3.6.1.6.3.1.1.4.3.0</OID>
<Syntax>6</Syntax>
<Value VariantType="8">.1.3.6.1.4.1.318</Value>
</SnmpVarBind>
</SnmpVarBinds>
</DataItem>
</EventData>
You may notice that these traps are being sent as SNMP v1. I am unable to change that on the UPS so i have modified the monitors to account for that. Here is the code for the monitor:
<UnitMonitor ID="UIGeneratedMonitorc2c65f3c85fe42f48ce8d2580c57bbae" Accessibility="Public" Enabled="true" Target="APC.MP.UPS" ParentMonitorID="Health!System.Health.AvailabilityState" Remotable="true" Priority="Normal" TypeID="SNL!System.NetworkManagement.SnmpTrapProvider.2SingleEvent2StateMonitorType" ConfirmDelivery="false">
<Category>Custom</Category>
<AlertSettings AlertMessage="UIGeneratedMonitorc2c65f3c85fe42f48ce8d2580c57bbae_AlertMessageResourceID">
<AlertOnState>Warning</AlertOnState>
<AutoResolve>true</AutoResolve>
<AlertPriority>Normal</AlertPriority>
<AlertSeverity>Error</AlertSeverity>
</AlertSettings>
<OperationalStates>
<OperationalState ID="UIGeneratedOpStateId2750c1ab2cd14b4a8a8e9f4633eba0b0" MonitorTypeStateID="SecondEventRaised" HealthState="Success" />
<OperationalState ID="UIGeneratedOpStateId5753748399984d08953c1a46895df99c" MonitorTypeStateID="FirstEventRaised" HealthState="Warning" />
</OperationalStates>
<Configuration>
<FirstIP>$Target/Property[Type="SNL!System.NetworkManagement.Node"]/SNMPAddress$</FirstIP>
<FirstVersion>1</FirstVersion>
<FirstOIDProps>
<OIDProp>.1.3.6.1.4.1.318</OIDProp>
</FirstOIDProps>
<FirstExpression>
<SimpleExpression>
<ValueExpression>
<XPathQuery Type="String">SnmpVarBinds/SnmpVarBind[OID=".1.3.6.1.6.3.1.1.4.1.0"]/Value</XPathQuery>
</ValueExpression>
<Operator>Equal</Operator>
<ValueExpression>
<Value Type="String">.1.3.6.1.4.1.318.0.5</Value>
</ValueExpression>
</SimpleExpression>
</FirstExpression>
<SecondIP>$Target/Property[Type="SNL!System.NetworkManagement.Node"]/SNMPAddress$</SecondIP>
<SecondVersion>1</SecondVersion>
<SecondOIDProps>
<OIDProp>.1.3.6.1.4.1.318</OIDProp>
</SecondOIDProps>
<SecondExpression>
<SimpleExpression>
<ValueExpression>
<XPathQuery Type="String">SnmpVarBinds/SnmpVarBind[OID=".1.3.6.1.6.3.1.1.4.1.0"]/Value</XPathQuery>
</ValueExpression>
<Operator>Equal</Operator>
<ValueExpression>
<Value Type="String">.1.3.6.1.4.1.318.0.9</Value>
</ValueExpression>
</SimpleExpression>
</SecondExpression>
</Configuration>
</UnitMonitor>
I tried the following things while attempting to troubleshoot this issue:
Leaving First
SnmpTrapProvider and Second
SnmpTrapProvider blank while creating the monitor.
Adding "" and also '' around the value as it is a string and perhaps that was the cause.
Changing the First and Second SNMPTrapProvider to .1.3.6.1.6.3.1.1.4.1.0 since that is the specific OID I am looking for the value of.
Reading every page of the internet and bashing my head on the keyboard.
I am guessing that the issue will reside in the the monitor creation and definition, but I have not found anything that clearly describes how to fill out the SNMP Trap Monitor wizard given the trap info. Especially since the trap I am receiving does
not seem to contain the usual OID with a common Int or string value. Hopefully someone can provide assistance as I am nearing my wits end with this problem.

Firstly, thank you Michael Skov, knowing that the First and Second SnmpTrapProvider or <FirstOIDProps> in the xml, needed to be blank got me pointed in the right direction. I figured I would come back and share my final working code snippet in case
others run across a similar issue.
<UnitMonitor ID="UIGeneratedMonitorf9f671e5456c44fd807d6ec2bd09621d" Accessibility="Public" Enabled="true" Target="Disc!APC.Disc.UPS" ParentMonitorID="Health!System.Health.PerformanceState" Remotable="true" Priority="Normal" TypeID="NetworkManagement!System.NetworkManagement.SnmpTrapProvider.2SingleEvent2StateMonitorType" ConfirmDelivery="false">
<Category>Custom</Category>
<AlertSettings AlertMessage="UIGeneratedMonitorf9f671e5456c44fd807d6ec2bd09621d_AlertMessageResourceID">
<AlertOnState>Warning</AlertOnState>
<AutoResolve>true</AutoResolve>
<AlertPriority>Normal</AlertPriority>
<AlertSeverity>Warning</AlertSeverity>
</AlertSettings>
<OperationalStates>
<OperationalState ID="UIGeneratedOpStateId8700c95344254f87a60c92d30d4a3953" MonitorTypeStateID="SecondEventRaised" HealthState="Success" />
<OperationalState ID="UIGeneratedOpStateId7bf68c6cfe3d4faabe83e630781c7327" MonitorTypeStateID="FirstEventRaised" HealthState="Warning" />
</OperationalStates>
<Configuration>
<FirstIP>$Target/Property[Type="NetworkManagement!System.NetworkManagement.Node"]/SNMPAddress$</FirstIP>
<FirstVersion>1</FirstVersion>
<FirstOIDProps />
<FirstExpression>
<SimpleExpression>
<ValueExpression>
<XPathQuery Type="String">SnmpVarBinds/SnmpVarBind[OID=".1.3.6.1.6.3.1.1.4.1.0"]/Value</XPathQuery>
</ValueExpression>
<Operator>Equal</Operator>
<ValueExpression>
<Value Type="String">.1.3.6.1.4.1.318.0.5</Value>
</ValueExpression>
</SimpleExpression>
</FirstExpression>
<SecondIP>$Target/Property[Type="NetworkManagement!System.NetworkManagement.Node"]/SNMPAddress$</SecondIP>
<SecondVersion>1</SecondVersion>
<SecondOIDProps />
<SecondExpression>
<SimpleExpression>
<ValueExpression>
<XPathQuery Type="String">SnmpVarBinds/SnmpVarBind[OID=".1.3.6.1.6.3.1.1.4.1.0"]/Value</XPathQuery>
</ValueExpression>
<Operator>Equal</Operator>
<ValueExpression>
<Value Type="String">.1.3.6.1.4.1.318.0.9</Value>
</ValueExpression>
</SimpleExpression>
</SecondExpression>
</Configuration>
</UnitMonitor>

Is it possible to transfer the temperature readings through "Serial I/O" port of Lakeshore temperature monitor?

With this monitor, you can have 2 analog outputs that you can transfer to the computer by using DAQ boards. In my case, I need temperature measurements at 3 different locations so I need 3 analog outputs, which is not possible with this device.
However, the monitor can also store temperature data in its memory and print the data. What I need is not to print the data but send the data to the computer somehow in digital form and postprocess it. I am using the "serial I/O" port to connect the device to the computer. I think I can do some configurations on the temperature monitor with the drivers in the link (http://sine.ni.com/apps/utf8/niid_web_display.download_page?p_id_guid=0241DD1B3AAF0341E0440003BA7CCD... ) but I am not sure if the device recognize the commands that I send through the I/O port.
Any advice on how to transfer (in digital form) the stored data on the monitor to the computer?

http://sine.ni.com/apps/utf8/niid_web_display.download_page?p_id_guid=0241DD1B3AAF0341E0440003BA7CCD...
and the temperature monitor is the one in this link: http://www.lakeshore.com/products/cryogenic-temperature-monitors/model-218/Pages/Overview.aspx
Actually, it says in the manual that the stored data can be send to either printer or they can be retrieved by the computer interface. However, there is not enough information about how to perform this task.
I am using labview to read the data for the analog outputs and the drivers in the first link are also in labview language. But with those drivers, I cannot retrieve the data to the computer.
I will check MAX to test the communication with the device, though. Thanks for the advice!

Good Temperature Monitor for C2D MBP??

Just got my 17" MBP and it's great!!
I am new to the laptop world, so if someone can recommend a temperature monitor (preferably free) that would be great.
It seems fine, but I'd like to be able to monitor this.
Cheers

It may actually be overkill......
But this is the best one I have found:
http://www.bresink.com/osx/HardwareMonitor.html
It is an amazing product.
SG
C2D 2.16(XP)/G52.0 DUAL/MDD 1.25 DUAL/867 12 inch/ and many more Mac OS X (10.4.8)

Temperature Monitor for OS 10.3.9

I need an application or console command that will show me the temperature of my CPU.
I'm running a Beige G3 that is using a G4 processor. It's running OS 10.3.9 through the use of the application xPostFacto. I've found the apps "Temperature Monitor 4.8" and "Hardware Monitor 4.8," but those don't support any Mac OSs below 10.4.x. Temperature Monitor 4.7 supports Mac OS 10.3.9, but I can't find a download of it for the life of me. All of the links redirect to version 4.8.
Please, any help would be much appreciated, my project is at a stand still until I can find something that works.
Thanks!

Click on my TMM name at left & send me an email. I'll send you the 10.3 version. Don't know if your Mac has the sensors to monitor the temps.
 Cheers, Tom

Temperature Monitor Alert:Memory controller heatsink Results!!!

Hello all...
I have a question about the Memory Controller Heatsink sensor in the temparature monitor and I would appreciate it if you could shed any light in my problem.
Well it was long time since I checked my temperatures on my G5 DP 2.3 so yesterday while I was into some MP3 encoding I heard the fans making alot of noise ,not something unbearable but not the usual silence behaviour I was used to even under heavy load and with the nap off.
So because of that noise I decide to check it with the temperature monitor but nothing unusual came up except...yes you guess it the Memory Controller heatsink.
An alert came up and inform me that the temp was over 75 C/167 F.
The threshold was by default at 75 C/167 F.
Let me add that it's summer here and a hot one at 37 C and the room is not airconditioning,but it was exactly the same one year ago(June 2005)and I never came up with an alert.
Also I have no problem with the rest indications.
So what do you think is it normal or may I have a broken fan?
And finally what is the Memory Controller Heatsink?
Thanx in advance!

The memory controller heatsink is shown, with the associated cooling tubes and fins, in the right-hand photo of the 'back' of the main logic board here
http://homepage.mac.com/jerrycube/jerrycubepix/22601bluebord.jpg
Air is pulled over the back of the main logic board and through the cooling fins, by the fan in a plastic housing, at 90deg to all the other fans, behind the hard drives.
This fan is called "Main Logic Board Backside" by Hardware Monitor in this ancient DP2.0 - and is showing "20%" in 22deg C room temperature. "Memory Controller Heatsink" is at 54deg C.
37deg C is above the specified max. 'Operating Temperature' of 35deg C shown here
http://support.apple.com/specs/powermac/PowerMac_G5_Late2005.html
I think it would probably be advisable to find some way of lowering the temperature of the room the G5 is in...

Cisco WCS integration with SNMP based monitoring

I am looking for a solution to integrate Cisco WCS with any SNMP based monitoring solution. My requirement is below,
- Alerts for Access points up/down should be picked up by an alerting system in its console through SNMP.
- I dont want all access points to be monitored, but only a critical group.
Currently all access points are configured on LWAP mode under a wireless controller. Can i configure APs individually for SNMP and get it monitored through the 3rd party monitoring tool.
Can anyone please guide me to find a solution for this.

http://www.cisco.com/en/US/docs/wireless/mse/3350/6.0/CAS/configuration/guide/msecg_ch2_CAS.html

Temperature monitor lite

temperature monitor lite has detected the SMART sensor on my 1.83 mbp... can anyone tell me what temperature range is "normal" for my machine?
thanks in advance.
MacBook Pro Mac OS X (10.4.6)

i know the whole heat thing has been done to death, but i was still hoping somone would humor me. i couldn't find a "normal" range listed in any other thread, or i wouldn't have posted.
and actually, sadly, my mbp isn't running just fine. among other issues, when it runs hot, my fan spins up and then down right away... i know, i know... the infamous "moo" has also been done to death. but before i send my machine away for service for two weeks (two weeks! an eternity) i thought a comparison with other users' experiences would be prudent...
anyone?

New MacPro: Good temperature Monitor Application for the nMP?

Can anyone suggest a good temperature monitoring application they have used for the new Mac Pro?
Thanks

I would recommend iStat Menus (http://bjango.com/mac/istatmenus/). I switched to it when I got the Mac Pro 2013 because Hardware Monitor doesn't work with the new Mac Pro. It's pretty good, although the history is only visual with graphs showing the evolution of the different sensors temperature. With Harware Monitor it was possible to read the temperature that were recorded at a certain point in time.

Best Temperature Monitoring Program?

Hey all, first time posting in the forums.
I recently got a mid-2012 MBP for college, so of course I immediately began putting games like Borderlands and GTA:SA on it. It runs anything I throw at it beautifully, but it gets awfully hot while it does. I know this is common for MBP's, even up to 90 degrees celsius, but it is something a tad worrisome when it gets over 80 (some games get it there every time....). So I've been trying to monitor it to at least be sure I'm not letting it get up there too often or for too long.
So had a few questions about temperature monitoring with Macs. I've currently got 3 programs running monitor temperature and system usage- System Pal, iStat Pro, and SMCfancontrol (which I also kick up a bit when playing the more GPU intensive games). The problem is that all three show different temperatures. Right now SystemPal reads 41 degrees celsius, SMCfancontrol reads 49, and iStat Pro has temps between 30 and 42 degrees. Which one's right? Is there a more accurate/definitive program for temp monitoring?
If it makes any difference, I usually play projected onto a 32 in LG TV using a thunderbolt to HDMI. I know this is more GPU intensive to begin with, but after going HD it feels a necessary evil.
If anyone happens to know of ways to keep temps down while gaming, monitor temps during full screen apps/games, or ways to monitor GPU usage (right now I have none ) I'd greatly appreciate advice on that too!
Thanks so much for answers!

Try iStat Menus 4.02 or Temperature Monitor 4.96 or Hardware Monitor 4.96.

How to Configure SNMP Counter Monitors

Hi there,
I want to receive a SNMP trap if attributes of the SNMP Agent (JMX
MBeans) change in WLS 6.1. I'm playing around with the PetStore
example that is part of the package. I enabled SNMP and configured
localhost as a TrapHost, great ! Now I want to configure a couple of
Counter and Attribute Monitors. What do I put for
Monitored MBean Type
Monitored MBean Name
Monitored Attribute Name
if I want to monitor e.g.
ejbEntityHomeRuntimeTransactionsCommittedTotalCount Attribute in the
EJBEntityHomeRuntime Table ??
I have trouble getting it working,
thanks for any help,
Alex
Bonus question: Do I need to do this always with the Admin Console or
can I edit the config.xml file myself ?

well, here is the way you can set up a SNMP String Monitor for monitoring
the changes to the FileName attribute in the LogMBean:
Monitored MBean Type - Log
Monitored MBean Name - myserver
Monitored Attribute Name - FileName
The easiest way to figure these attributes is with the help of the
JavaDocs for MBeans. Please verify the data type that the method returing
attribute that you are trying to monitor with the type of the monitor you
are trying to set.
ie, you cannot setup a String monitor for a boolean attribute in the
mbean.In the case above, the getFileName method returns a String object,
so it makes sense to set a String monitor for it!
You can setup your monitor for EJBEntityHomeRuntime in a similar fashion!
Its not necessary to specify the complete ObjectName in the
MonitoredMBeanName. as the WLS constructs it automatically from the the
Name, Type and the target to which you target this trap monitor.
Hope this helps,
Mihir
Alex wrote:
Hi there,
I want to receive a SNMP trap if attributes of the SNMP Agent (JMX
MBeans) change in WLS 6.1. I'm playing around with the PetStore
example that is part of the package. I enabled SNMP and configured
localhost as a TrapHost, great ! Now I want to configure a couple of
Counter and Attribute Monitors. What do I put for
Monitored MBean Type
Monitored MBean Name
Monitored Attribute Name
if I want to monitor e.g.
ejbEntityHomeRuntimeTransactionsCommittedTotalCount Attribute in the
EJBEntityHomeRuntime Table ??
I have trouble getting it working,
thanks for any help,
Alex
Bonus question: Do I need to do this always with the Admin Console or
can I edit the config.xml file myself ?

CPU temperature monitoring utility - It works!!!

After long seeking and testing many HW monitoring programs it works! CPU temp monitoring on toshiba notebooks! Hmonitor v4.2.5.1 at http://hmonitor.com/
Good luck!

Hi sauliaus
Thanks for your information.
I have checked some postings and it seems that some user would like to install the temperature monitoring utility.
I'm sure this post will help many users.
Thanks again ;)
Bye

Room Temperature Monitoring

Dear All,
I need to develope a room temperature monitoring system which will alert by send mails when the temperature goes high. I just wanted to know whether there is any such hardware in the market, together with java, I can acheive this. Any help will be greatly appretiated. Thanks in advance. You can also mail me to [email protected] Thanks once again.
Ramya.

ramya1us,
Have a look at http://www.ibutton.com/ibuttons/thermochron.html and at http://ibutton.com.ibuttons/java.html . They seem to sell plenty of hardware and information on writing software to interface with it.
I know of someone who has bought some of their hardrware and created a user controllable WebCam with it.
Hope this helps.
Guy

ASA5520 SNMP temperature monitoring

Similar Messages

Maybe you are looking for