Creating SNMP Trap Monitors in 2012 R2

Hello,
For the past week or so I have been attempting to create a MP for my company's UPSs to be monitored in SCOM 2012 R2. I have created a custom MP with custom datasources and objects. All seems to go according to the plan until I attempt to create a SNMP
Trap monitor for those objects. I am able to verify that the device is discovered and is sending the traps successfully with a view. The problem seems to lie within the setup of the monitor. I have followed the steps as much as I can from this page http://technet.microsoft.com/en-us/library/hh563870.aspx
to create a monitor that will be triggered by an incoming trap saying the UPS is on Battery Power.
This is the initial or trigger event information received by SCOM:
<EventData>
<DataItem type="System.SnmpData" time="2014-07-03T08:48:07.6990732-07:00" sourceHealthServiceId="26DF02E5-DEA0-BED0-443B-3605A05D4790">
<Source>10.51.85.40</Source>
<Destination>127.0.0.1</Destination>
<ErrorCode>1</ErrorCode>
<Version>1</Version>
<SnmpVarBinds>
<SnmpVarBind>
<OID>.1.3.6.1.2.1.1.3.0</OID>
<Syntax>67</Syntax>
<Value VariantType="19">17567220</Value>
</SnmpVarBind>
<SnmpVarBind>
<OID>.1.3.6.1.6.3.1.1.4.1.0</OID>
<Syntax>6</Syntax>
<Value VariantType="8">.1.3.6.1.4.1.318.0.5</Value>
</SnmpVarBind>
<SnmpVarBind>
<OID>.1.3.6.1.4.1.318.2.3.3.0</OID>
<Syntax>4</Syntax>
<Value VariantType="8">UPS: On battery power in response to an input power problem.</Value>
</SnmpVarBind>
<SnmpVarBind>
<OID>.1.3.6.1.6.3.1.1.4.3.0</OID>
<Syntax>6</Syntax>
<Value VariantType="8">.1.3.6.1.4.1.318</Value>
</SnmpVarBind>
</SnmpVarBinds>
</DataItem>
</EventData>
This is the event should signal that everything is operating normally once again.
<EventData>
<DataItem type="System.SnmpData" time="2014-07-03T08:48:12.9133769-07:00" sourceHealthServiceId="26DF02E5-DEA0-BED0-443B-3605A05D4790"><Source>10.51.85.40</Source>
<Destination>127.0.0.1</Destination>
<ErrorCode>1</ErrorCode>
<Version>1</Version>
<SnmpVarBinds>
<SnmpVarBind>
<OID>.1.3.6.1.2.1.1.3.0</OID>
<Syntax>67</Syntax>
<Value VariantType="19">17567730</Value>
</SnmpVarBind>
<SnmpVarBind>
<OID>.1.3.6.1.6.3.1.1.4.1.0</OID>
<Syntax>6</Syntax>
<Value VariantType="8">.1.3.6.1.4.1.318.0.9</Value>
</SnmpVarBind>
<SnmpVarBind>
<OID>.1.3.6.1.4.1.318.2.3.3.0</OID>
<Syntax>4</Syntax>
<Value VariantType="8">UPS: No longer on battery power.</Value>
</SnmpVarBind>
<SnmpVarBind>
<OID>.1.3.6.1.6.3.1.1.4.3.0</OID>
<Syntax>6</Syntax>
<Value VariantType="8">.1.3.6.1.4.1.318</Value>
</SnmpVarBind>
</SnmpVarBinds>
</DataItem>
</EventData>
You may notice that these traps are being sent as SNMP v1. I am unable to change that on the UPS so i have modified the monitors to account for that. Here is the code for the monitor:
<UnitMonitor ID="UIGeneratedMonitorc2c65f3c85fe42f48ce8d2580c57bbae" Accessibility="Public" Enabled="true" Target="APC.MP.UPS" ParentMonitorID="Health!System.Health.AvailabilityState" Remotable="true" Priority="Normal" TypeID="SNL!System.NetworkManagement.SnmpTrapProvider.2SingleEvent2StateMonitorType" ConfirmDelivery="false">
<Category>Custom</Category>
<AlertSettings AlertMessage="UIGeneratedMonitorc2c65f3c85fe42f48ce8d2580c57bbae_AlertMessageResourceID">
<AlertOnState>Warning</AlertOnState>
<AutoResolve>true</AutoResolve>
<AlertPriority>Normal</AlertPriority>
<AlertSeverity>Error</AlertSeverity>
</AlertSettings>
<OperationalStates>
<OperationalState ID="UIGeneratedOpStateId2750c1ab2cd14b4a8a8e9f4633eba0b0" MonitorTypeStateID="SecondEventRaised" HealthState="Success" />
<OperationalState ID="UIGeneratedOpStateId5753748399984d08953c1a46895df99c" MonitorTypeStateID="FirstEventRaised" HealthState="Warning" />
</OperationalStates>
<Configuration>
<FirstIP>$Target/Property[Type="SNL!System.NetworkManagement.Node"]/SNMPAddress$</FirstIP>
<FirstVersion>1</FirstVersion>
<FirstOIDProps>
<OIDProp>.1.3.6.1.4.1.318</OIDProp>
</FirstOIDProps>
<FirstExpression>
<SimpleExpression>
<ValueExpression>
<XPathQuery Type="String">SnmpVarBinds/SnmpVarBind[OID=".1.3.6.1.6.3.1.1.4.1.0"]/Value</XPathQuery>
</ValueExpression>
<Operator>Equal</Operator>
<ValueExpression>
<Value Type="String">.1.3.6.1.4.1.318.0.5</Value>
</ValueExpression>
</SimpleExpression>
</FirstExpression>
<SecondIP>$Target/Property[Type="SNL!System.NetworkManagement.Node"]/SNMPAddress$</SecondIP>
<SecondVersion>1</SecondVersion>
<SecondOIDProps>
<OIDProp>.1.3.6.1.4.1.318</OIDProp>
</SecondOIDProps>
<SecondExpression>
<SimpleExpression>
<ValueExpression>
<XPathQuery Type="String">SnmpVarBinds/SnmpVarBind[OID=".1.3.6.1.6.3.1.1.4.1.0"]/Value</XPathQuery>
</ValueExpression>
<Operator>Equal</Operator>
<ValueExpression>
<Value Type="String">.1.3.6.1.4.1.318.0.9</Value>
</ValueExpression>
</SimpleExpression>
</SecondExpression>
</Configuration>
</UnitMonitor>
I tried the following things while attempting to troubleshoot this issue:
Leaving First
SnmpTrapProvider and Second
SnmpTrapProvider blank while creating the monitor.
Adding "" and also '' around the value as it is a string and perhaps that was the cause.
Changing the First and Second SNMPTrapProvider to .1.3.6.1.6.3.1.1.4.1.0 since that is the specific OID I am looking for the value of.
Reading every page of the internet and bashing my head on the keyboard.
I am guessing that the issue will reside in the the monitor creation and definition, but I have not found anything that clearly describes how to fill out the SNMP Trap Monitor wizard given the trap info. Especially since the trap I am receiving does
not seem to contain the usual OID with a common Int or string value. Hopefully someone can provide assistance as I am nearing my wits end with this problem.

Firstly, thank you Michael Skov, knowing that the First and Second SnmpTrapProvider or <FirstOIDProps> in the xml, needed to be blank got me pointed in the right direction. I figured I would come back and share my final working code snippet in case
others run across a similar issue.
<UnitMonitor ID="UIGeneratedMonitorf9f671e5456c44fd807d6ec2bd09621d" Accessibility="Public" Enabled="true" Target="Disc!APC.Disc.UPS" ParentMonitorID="Health!System.Health.PerformanceState" Remotable="true" Priority="Normal" TypeID="NetworkManagement!System.NetworkManagement.SnmpTrapProvider.2SingleEvent2StateMonitorType" ConfirmDelivery="false">
<Category>Custom</Category>
<AlertSettings AlertMessage="UIGeneratedMonitorf9f671e5456c44fd807d6ec2bd09621d_AlertMessageResourceID">
<AlertOnState>Warning</AlertOnState>
<AutoResolve>true</AutoResolve>
<AlertPriority>Normal</AlertPriority>
<AlertSeverity>Warning</AlertSeverity>
</AlertSettings>
<OperationalStates>
<OperationalState ID="UIGeneratedOpStateId8700c95344254f87a60c92d30d4a3953" MonitorTypeStateID="SecondEventRaised" HealthState="Success" />
<OperationalState ID="UIGeneratedOpStateId7bf68c6cfe3d4faabe83e630781c7327" MonitorTypeStateID="FirstEventRaised" HealthState="Warning" />
</OperationalStates>
<Configuration>
<FirstIP>$Target/Property[Type="NetworkManagement!System.NetworkManagement.Node"]/SNMPAddress$</FirstIP>
<FirstVersion>1</FirstVersion>
<FirstOIDProps />
<FirstExpression>
<SimpleExpression>
<ValueExpression>
<XPathQuery Type="String">SnmpVarBinds/SnmpVarBind[OID=".1.3.6.1.6.3.1.1.4.1.0"]/Value</XPathQuery>
</ValueExpression>
<Operator>Equal</Operator>
<ValueExpression>
<Value Type="String">.1.3.6.1.4.1.318.0.5</Value>
</ValueExpression>
</SimpleExpression>
</FirstExpression>
<SecondIP>$Target/Property[Type="NetworkManagement!System.NetworkManagement.Node"]/SNMPAddress$</SecondIP>
<SecondVersion>1</SecondVersion>
<SecondOIDProps />
<SecondExpression>
<SimpleExpression>
<ValueExpression>
<XPathQuery Type="String">SnmpVarBinds/SnmpVarBind[OID=".1.3.6.1.6.3.1.1.4.1.0"]/Value</XPathQuery>
</ValueExpression>
<Operator>Equal</Operator>
<ValueExpression>
<Value Type="String">.1.3.6.1.4.1.318.0.9</Value>
</ValueExpression>
</SimpleExpression>
</SecondExpression>
</Configuration>
</UnitMonitor>

Similar Messages

How to create snmp trap signal

hello friends,
I am going to create NMS tool for my wireless devices.
We are using java for front end monitoring.
For my project work, how can I create SNMP Trap signal.?
Any examples is there.
thank you.
Rgds,
ram

There are many ways to modify the array to do what you want. One of my favorites is to use the "Insert Into Array" function. Just build an array of each waveform you wish to generate and arrays of 0 or NaN (depending on what you agilent device will accept) for the no signal gaps. Append them all together and you will have your arbitrary waveform for your generator.
Kyle K.
Product Manager for Product Data
National Instruments

After upgrading to NX-OS 5.04, out snmp traps monitoring system is not generating ticket / incident for the snmp traps and my question is whether we need to apply new MIBS for that?

after upgrading to NX-OS 5.04, out snmp traps monitoring system is not generating ticket / incident for the snmp traps and my question is whether we need to apply new MIBS for that?

Looking at the error message "The Network Adapter could not establish the connection" , It appears hostname and port may be incorrect. Review the targets.xml under E:\oracle\product\10.2.0\db_1\SAP_solman_SDB\emd and
emoms.properties under E:\oracle\product\10.2.0\db_1\SAP_solman_SDB\config folder to make sure host ( sap_solman) and port (1527) are correct.
As far as setting the environment variables goes, you can go to control panel -> system -> advanced -> environment variables and set the ORACLE_HOME and ORACLE_SID
-Ramesh

SNMP Traps Monitoring problem.

Hi,
Hear is my problem. I am using SNMP Traps as Auto-Reaction Method to monitor some files system. I am already receiving Traps when the file exceeds the thresholds value (when change from Green to Yellow and when change from Yellow to Red). The problem that Im having is that I am not receiving Traps to reset these values (Reset from Red to Yellow and Reset from Yellow to Green). What do I have to do to receive those traps?

Hi Santiago,
I am trying to send snmp alert from solution manager to Tivoli enterprise console. I did all configuration based on SAP document but Tivoli team keep saying that they did not receive anything. There is no way i can test on my side that what is the problem. When aler is generated, i see the MTE goes red and then alert status shows " Action required". However if I change the method to email, i receive emails. it is only SNMP which does not work.
Can you tell if i need to setup special parameter in SNMP method which i am missing. I did the following:
HOST - Tivoli server
Trapsort - UDP
Port - 162
MIB_DIR = /usr/sap//SID/SYS/exe/run/MIBS
Also is there any settings which Tivoli team has to do for receiving traps? It is possible for you to share the setup document? you can send it to me on [email protected]
Thanks for ur help.
Pavan

SCOM 2012 SNMP Trap - Does anyone have it working?

I am wondering if anyone out there has had any luck with getting SNMP Traps to be captured by SCOM 2012? Probes work fine.
We have been unable to get SCOM 2012 to receive a SNMP Trap from network devices. We currently have a case open with Microsoft, but they dont have any answers as of yet.
Here are the cliff notes version of what we have done so far.
Discovery - OK
The nodes discover without issue. I made sure they were set to SNMP only. I did this to verify we were talking SNMP and not just ICMP.
Open Ports/Firewall Issues
No firewalls are in place on the SCOM server and none exist between devices we are trying to get traps from. Using a port tool, I can see that UDP 162 is listening as expected and its the System Center Management Host Process that is running the
process. We have tried having SNMP installed, but disabled, installed and running, and uninstalled. Currently we have the SNMP service installed and running. The SNMP Trap Service is NOT installed.
Data Validation
Using Wireshark running on the SCOM box I have been able to validate the OIDs we are searching for are hitting the SCOM server. I installed an SNMP Trap generator and Receiver on my local machine as well as Jalasoft SNMP Simulator. I was able
to discover my local machine as a network device and if I send a TRAP from the TRAP generator on my local machine to the receiver on my local machine I can validate the data is coming through ok.
What has been done on SCOM side
The simplest place to look for data is with an Event Collection Rule and then an Event View Monitor. We have set up an Event Based Monitor to search for an OID that I know to be accurate and then I set up an Event monitor to look for
anything hitting that Collection Rule. The Event monitor showed nothing so we changed the EVent Monitor to look for anything that hit Node which should show any SNMP traps that have hit from network devices. No results.
We tried to run WFAnalyzer from the 2007R2 Authoring Console, but it wont run against 2012 and from what I have found the 2012 edition doesnt exist anywhere yet.
So has anyone succesfully received a SNMP TRAP into SCOM 2012?

Hi,
As this thread has been quiet for a while, we assume that the issue has been resolved. At this time, we will mark it as "Answered" as the previous steps should be helpful for many similar scenarios.
In addition, we’d love to hear your feedback about the solution. By sharing your experience you can help other community members facing similar problems.
Thanks,
Yog Li
TechNet Community Support
How could you possibly mark this as answered? No answer was given, it was quiet for a couple of days including one of which was a holiday in the US. The previous steps are NOT helpful. The question remains, Does anyone have it working?
People have given troubleshooting advice, but nobody has actually answered the simple question. Do they have it actually WORKING?

No SNMP traps from sun x4150 ILOM server

Hi all,
I have set up the ILOM alerts with SNMP traps (v2c,public) according to the ILOM user guide and pressed the "send test alerts". Nothing shows up in the SNMP trap monitor (using MG-SOFT software). When I add another alert of IPMI pet type (same destination ip as of SNMP trap alert) I see events in the trap monitor. It looks like the ILOM does not generate SNMP traps but only IPMI traps.
In the ILOM user guide there is an explicit example of traps sent from the ILOM (in addition to the fact that the ILOM features include SNMP traps AS WELL as IPMI) so it seems this is possible...
my ILOM version is
SP Firmware Version 2.0.2.6
Does anyone have any idea of any step I have missed ?
Thanks in advance.
Lior

Once the Network Device (Linux server in this case) is discovered you will still need a rule that targets that class and accepts incoming SNMP Traps for that OID, or All OIDs if you prefer. I found 2 links that may be of help, the first is just a basic
overview of the SNMP listener in SCOM 2012 as it has changed from the OS Listener in 2007 to a dedicated one.
http://systemcentertech.com/2012/05/17/scom-2012-built-in-snmp-trap-listener/
The second link covers SNMP setup, but starting at Step 7 there is a great how-to on creating your own SNMP rule which will be needed to collect your traps.
http://scom-2012.blogspot.com/2012/07/setting-up-snmp-monitoring-in-scom-2012.html
www.Practice2Perfect.com

SNMP traps not capture in SCOM

we required to capture traps sent from the proofpoint(linux base) device - snmp v2 and display on SCOM but it does not work. we can saw the traps reach SCOM by using network trace.

Hi
Check this
http://stefanroth.net/2014/04/07/scom-2012-snmp-traps-how-the-heck-do-i-get-it-working/ and thishttp://blogs.technet.com/b/kevinholman/archive/2015/02/03/snmp-trap-monitoring-with-scom-2012-r2.aspx
and this
http://blogs.msdn.com/b/wei_out_there_with_system_center/archive/2014/02/15/opsmgr-customizing-the-snmp-trap-collection-rule-for-all-snmp-version-traps.aspx .
I think this should solve your Problems.
Cheers,
Stefan
Blog: http://stefanroth.net If my post helped you, please take a moment to vote as helpful and\or mark as an answer

SCOM 2012 SP1 - Show on event view all snmp trap (SNMP monitoring work)

Hello everybody,
Sorry for my english, I write normaly in french, but we have more result in english.
I have a problem with SCOM 2012. I try to catch all snmp traps sended by a 2960 CISCO switch on a EventView with a specific rule (Authoring->Rule->Collection Rules -> Event Based -> SNMP Trap (Event) based on the object target "Node")
I creat a specific management pack juste for the rule and the views.
SNMP Monitoring - CISOC 2960 => It's OK, I can have the processor state, utilization, etc ...
SNMP Monitoring Ubuntu computer => It's OK, I can have all the state I want.
SNMP Traps => The switch or the computer send traps over the network, and I can see in wireshark, the server receive the traps
SNMP Service (Windows service) => Disabled
SNMP trap (Windows service) => Disabled
Health Service (Windows service) => Enabled
Port 162 UDP => Open and listenning by the MonitoringHost.exe
Firewall rules => Everythinks is OK
SNMP Trap send version is => 2c
SNMP Monitoring device version is => 2c
I try too many of solution on different web site like :
http://scom-2012.blogspot.ch/2012/07/setting-up-snmp-monitoring-in-scom-2012.html
http://social.technet.microsoft.com/Forums/systemcenter/en-US/731661b9-10a1-4d3f-ba83-8e84d25ab760/event-collection-for-network-devices-scom-2012
http://social.technet.microsoft.com/Forums/systemcenter/en-US/a15bce49-fb62-4fd4-93cf-f87c3b734d58/snmp-trap-based-monitoring?forum=operationsmanagergeneral
http://social.technet.microsoft.com/Forums/systemcenter/en-US/41f5b6ef-c8b9-461d-bdcb-81fde5a89f50/scom-2012-unable-to-monitor-snmp-traps?forum=operationsmanagergeneral
http://social.technet.microsoft.com/Forums/systemcenter/en-US/4051fbd1-06f1-49e0-9ad4-4cbe4d2d7d4d/discover-windows-computer-as-network-device-w-snmp?forum=operationsmanagerauthoring
http://technet.microsoft.com/en-us/library/hh563870.aspx
http://social.technet.microsoft.com/Forums/en-US/cad1d3f9-594f-4f06-a5aa-660ccc2e9192/snmp-trap-based-monitoring-in-scom-2012-sp1?forum=operationsmanagerauthoring
http://social.technet.microsoft.com/Forums/en-US/41f5b6ef-c8b9-461d-bdcb-81fde5a89f50/scom-2012-unable-to-monitor-snmp-traps?forum=operationsmanagergeneral
http://social.technet.microsoft.com/Forums/en-US/e05a1c8f-7280-4f80-86cf-aabb4269bb87/scom-2012-customizing-snmp-trap-event-data?forum=operationsmanagergeneral
http://social.technet.microsoft.com/Forums/en-US/6826f6a6-bbc3-444b-9b18-288d7fedac3e/scom-unable-to-monitor-snmp-traps?forum=operationsmanagergeneral
http://social.technet.microsoft.com/Forums/en-US/7cd1571a-d292-4efc-9921-5a068f6f1691/scom-2012-sp1-ur2-snmp-monitoring?forum=operationsmanagermgmtpacks
Do you know a workaround? Or a different way to catch all the traps from a network device and show them (traps) on a event views.
Thank you in advance.
KimBaxZ
Computer expert system technology

Hello Yan Li,
I read your link, and I found this :
The network devices must be discovered and registered as ICMPSNMP devices.
And when I make the dicovery the first time, ICMP doesn't work, so I put only SNMP. This morning I tried with ICMP and SNMP, but the same problem come to me. And I found the rootcause of the problem with this post : http://www.code4ward.net/main/Blog/tabid/70/EntryId/105/Troubleshooting-Network-Discovery-in-SCOM-2012.aspx
I allowed the SNMP service, ping, and Health Service, just after I try a second time to dicover my device and it's work (ICMP and SNMP).
I recreat all my management pack and the rule. And now it's work! Thank you very much for your help!!
Have a nice day
Best regards
KimBAxZ
Computer expert system technology

SCOM 2012 unable to monitor SNMP traps

After installing SCOM 2012 I did not
get the SNMP Trap. I tried the solution
of the topics http://social.technet.microsoft.com/Forums/en-US/operationsmanagergeneral/thread/6826f6a6-bbc3-444b-9b18-288d7fedac3e Nothing
has helped.
Help please, why SCOM can
not take Traps?

We had the an issue where device was sending SNMP v1 traps as per Wireshark but the device was discovered as a SNMP v2 device. We forced the device to be discovered as a SNMP v1 device and that worked.
To do so, after you add the device that needs to be discovered within the discovery rule, export the MP called Network Discovery Internal. Open this in notepad and browse to the IP address of your device that needs to be discovered. Change the value for
"AutoDetect" to v1 in case you want to discover his as a V1 DEVICE. Then you will be able to receive traps from the said device that got discovered.
<SeedSystem>
                  <SeedIPorName>10.100.x.x</SeedIPorName>
                  <Version>AUTODETECT</Version>
                  <SNMPPort>161</SNMPPort>
                </SeedSystem>
Hope this helps.
Kapil Dham

Monitoring SNMP Traps from Windows Server

Hello All
im looking for a way to monitor an application that runs with os windows server 2003 and windows 2008 r2 and send its alarms as a snmp traps with system center operations maanger 2012 R2.
in the scom 2007 environment i could discover the servers as network device and recive traps and genrate alerts.
is there a way to edit the existing management pack to enable the windows server discovery as a network device
and enable traps with a microsoft oid to be resived ?
i understand that this is by desigin from
http://technet.microsoft.com/en-us/library/hh212935.aspx
or is there another option to create this monitor with scom 2012 R2?
Thank you

Hello Yan.
thank you for the replay i understand that this is by design,
what im looking for is a way to edit the management pack that discard those OID
or even a 3rd part solution to monitor windoes server snmp genrated alerts.
thank you

SNMP traps from EMC SRM to SCOM 2012 R2

Hi,
I'm trying to configure SCOM 2012 R2 as an SNMP trap listner. I've seen many articles on setting this up but all are based around SNMP traps from network devices which must first be discovered and identified in the network device list.
However in my scenario I am trying to monitor/listen for traps send by a Linux box hosting EMC SRM - this management software can be configured to send SNMP traps out so it is these that I need to try and listen for/capture.
So can anyone explain how I can configure SCOM 2012 R2 to do this. I have tried to just used the IP of the Linux box and discover it as a network device but it fails - in Network Devices Pending Mgmt it says No response Ping, even though I can
ping the box from the Server OK - so I am guessing you cant cheat scom in discovering the Linux box as a network device in ths way?
Can anyone offer any advice for setting this up. Just to add I've ensured the RunAs Community String (public) and SNMP version is correct on both side...
Cheers...

Once the Network Device (Linux server in this case) is discovered you will still need a rule that targets that class and accepts incoming SNMP Traps for that OID, or All OIDs if you prefer. I found 2 links that may be of help, the first is just a basic
overview of the SNMP listener in SCOM 2012 as it has changed from the OS Listener in 2007 to a dedicated one.
http://systemcentertech.com/2012/05/17/scom-2012-built-in-snmp-trap-listener/
The second link covers SNMP setup, but starting at Step 7 there is a great how-to on creating your own SNMP rule which will be needed to collect your traps.
http://scom-2012.blogspot.com/2012/07/setting-up-snmp-monitoring-in-scom-2012.html
www.Practice2Perfect.com

Operations Manager 2012 doesn't listening SNMP Trap UDP port 162

hi,
SCOM 2012 SP1, how come the operations manager started but the SNMP Trap UDP port 162 not listening?
Without this port listening, I can't testing SNMP trap on SCOM.
Thanks...KEN

Hi,
As described in the following blog, the TRAP service should be installed but turned off, we could not get traps coming in until we turned the service back on.
So please verify if the service is on. You can continue audit the ports by running netstat –a.
System Center 2012 Notes From the Field
http://scom-2012.blogspot.in/2012/07/setting-up-snmp-monitoring-in-scom-2012.html
Please Note: Since the web site is not hosted by Microsoft, the link may change without notice. Microsoft does not guarantee the accuracy of this information.
Hope this helps.

CCMS agents, alert monitoring, SNMP traps

Hi Guys,
I have a question. There is a requirement about monitoring. Any documenation or links will be really appreciated.
My client needs me to use CCMS agents, alert monitoring for both ABAP and JAVA stacks, SNMP traps, sending SNMP traps, interface CCMS with third party monitoring tools. Mostly, the ,monitoring is done thru RZ20.
Anybody can point me in right direction or material.
Thanks
Venky

Hi,
Check these CCMS Weblogs. Really good ones...
/people/federico.babelis2/blog/2006/04/26/ccms-rule-based-monitors-configuration-guide-for-dummies
/people/aravindh.prasanna/blog/2005/12/23/configuring-scenario-specific-e-mail-alerts-in-xi-ccms-part--1
/people/aravindh.prasanna/blog/2006/02/20/configuring-scenario-specific-e-mail-alerts-in-xi-ccms-part-3
Feel free to revert back.
--Ragu

SNMP traps to monitor the signal strength on wireless AP

What snmp notification type should I enable on wireless AP to monitor the signal strength of the connected devices to the AP. What is the associated MIB for this SNMP trap.

Hi karthikeya,
Here is the link which gives us the info regarding the available MIB for the respective Model..
http://tools.cisco.com/ITDIT/MIBS/MainServlet?ReleaseSel=3469&PlatformSel=9&fsSel=1292
Please select the Device part number and then chose the MIB that you require.
lemme know if this answered your question..
Regards
Surendra
====
Please dont forget to rate the posts which answered your question and mark it as answered or was helpfull

ASA /Router -SNMP Trap when IP SLA monitored (ICMP timeout)

Hi,
I am looking for some solution for my below requirment
Requirment is :
How do I configure ASA or Router to send SNMP Trap when IP SLA monitored features enabled (ICMP request or 900 millisecond delay from destination IP)
Thanks in advance..

Hi,
Maybe this thread might help you?
https://supportforums.cisco.com/thread/2039293
I have not personally configured these type of SLA configurations on an ASA other than for testing purposes. We handle Dual ISP setups outside the ASA firewalls.
- Jouni

Creating SNMP Trap Monitors in 2012 R2

Similar Messages

Maybe you are looking for