At wit's end with Add-On disconnecting. HELP!

I've now been struggling with this problem for the better part of a week trying different things, working with SAP support -- but to no avail.
Here's the deal: I wrote a simple add-on using the UI-API. It adds one button to Order Entry. I run the add-on through VB.NET with SBO running and it works great. I compile, create the add-on installer, create the .ard file and add the add-on in SBO.
The add-on installs just fine. Now when I go to start the add-on in SBO (whether automatic or manual), the add-on will disconnect and send me the message "Add-on...is disconnected. Restart, Ignore, Continue...". I've narrowed down the disconnection to the line of code where the add-on is grabbing the Application: SBO_Application = SboGuiApi.GetApplication()
I've now gone as far as using the simple "Hello World" sample from the SDK and I don't change anything. It still has the same problem.
I've upgraded to patch 32 (per SAP's instructions) and it still doesn't help.
HELP!! Any ideas??
I really appreciate it. If someone helps solve this problem, I will buy you dinner.
Thanks,
Curtis

Are you getting the connection string from the UI API - you MUST NOT use the development string
sConnectionString = "0030002C0030002C00530041005000420044005F00440061007400650076002C0050004C006F006D0056004900490056"
Here is a code snippet (VB .NET 2003) that will show you how to get the string from the UI API
#If DEBUG Then
            '1a. This is for Testing Purposes
            sConnectionString = "0030002C0030002C00530041005000420044005F00440061007400650076002C0050004C006F006D0056004900490056"
#Else
            '1b. This is for Add-On Purposes
            sConnectionString = Environment.GetCommandLineArgs.GetValue(1)
#End If
(ensure the development string is not set up in the project properties and compile your .exe in release mode - recompile your installer with the new exe and then create a new .ard file and install)
if all else fails add message boxes to every line of your .exe startup cade and see where the app breaks - then you wil have an idea of how to fix it (you can also catch exceptions to check the system errors)
Hope this helps..

Similar Messages

At wit's end with imovie project -- need Help!

Aloha:
I am in the middle of doing a documentary movie of the yearly Air Show put on by my RC model airplane club. Over the past several years I have made a handful of other documentaries and all with out problem, they worked just fine.
On this one, however, I have run into problems that are new and completely frustrating. I have finished editing the movie and all works well in the iMovie mode. I can play the entire movie and all the parts and pieces work just fine. But when I burn the results onto a DVD some scenes (only a few) lose camera audio. This is also true if I export it to Quicktime.
My movie uses camera audio, imported background music and narrative voice-over. And all those play just fine in the iMovie program. But there are several spots where the camera audio doesn't come across in the final product, just total silence except for the background music or any voice-over narrations that may be present during those times. The camera audio just does not come through.
I am at wit’s end and need some help. Has anyone come across this and what did you do to fix it?
Thanks
Dan Page
Maui, Hawaii

Hi: Thank you very much for the rapid come back, most appreciated.
Hi Dan
A wild guess. Can it be so that those clips are
recorded in Your Camera with
the sound set to 12-bit (often factory/default set).
Should be 16-bit
I'll check the camera for that, but the same camera was used in all the clips and only two or three were missing audio when exported.
Try to extract the missing sounds from each clip and
redo a disk image in
iDVD and see if the sound is back.
That sounds like a great diagnostic and should be far less time consuming than burning a DVD.
Thanks for the hints.
Dan Page
Yours Bengt W

At my wits end with BT - can anyone help please?

This is a long and ongoing saga and so I apologise for the long post.
In February due to a change in job I needed to change the payment date of my DD payment. I did this online and received an email confirming the new payment date of the 28th. I stupidly assumed that was the date BT would take payment. The account is only used for Direct Debits and so money is put in there shortly before they're due. Over two weeks before the payment was due I received an unpaid DD letter from my bank. BT had attempted to take the payment early. I contacted BT and was assured my payment date was the 28th and they had no idea why payment had been attempted early. Later that day BT called to discuss the returned DD and I explained it was a BT error. A week later BT attempted to take the DD again. Once again I contacted them to be told my DD was definitely set up for the 28th and "there must be an error on the system" Later that day I received another call from BT to inform me my DD had been returned unpaid and again I explained that it was a BT error. Not trusting BT I cancelled the DD with the intention of making my payment online on the 28th. On 28th Feb before I had chance to make the payment I received a call from someone at BT who was mentioning late payment charges etc. I made it clear that any charges would be unacceptable as the error was down to BT and my payment wasn't actually late. I was asked to make payment over the phone but as it was difficult to understand each other I made it online and gave the payment reference number.
My online balance at this point showed as zero and so I decided against setting up another DD for BT to attempt to take money as and when they pleased. Late March I received a phone call from BT telling me my DD wasn't set up and I had an outstanding balance of £57.75. I explained I'd had a zero balance but it would appear that my online balance was showing incorrectly. The person I spoke to said he could set up a new DD for this amount but as a one off it would come out on the 13th - something to do with making sure payment was made before the new bill came out and it taking X amount of time for a DD to set up. This would be a one off payment and after it had been made I'd be contacted to set up a new DD.
On 20th April I received a call from UK based BT asking did I want to set up my new DD However to do this I would need to pay £120 over the phone. I asked why when I definitely had a zero balance, I'd received no bill and quite simply owed BT no money at that point. I was told there was a problem seeing all the data and somebody would call me back after the Easter weekend. Instead later that same day somebody else UK based phoned me asking me to set up my DD. I explained about the earlier phone call and she was confused as to why I'd been asked to pay anything as I clearly had a zero balance. I set up a new DD with her for £60 a month, payments to be made on 28th, starting 28th May. A few days after this my new bill arrived for £109.
On 5th May my bank called me to say once again BT had attempted to take the DD early but this time they'd attempted to take £109. Once again I called BT and this time spoke to an Indian gentleman who advised me to cancel the DD with my bank while I was on the phone with him, he'd cancel it at that end and then he would set up a new one. He said letters of confirmation would be sent out to me.
I sent an email to BT explaining all this and also saying I wasn't happy that they'd charged me £10 late payment charge on the new bill for unpaid DD. Had BT taken the payment when they should it wouldn't have been unpaid!! A gentleman phoned me back, assured me the £60 a month DD was set up for the 28th starting 28th May. He also emailed me confirmation of this.
On 9th May I received an email saying I had a "supplementary bill" so looked at my online account to see my bill had gone up by about £5. My DD wasn't showing as set up on the online account but I decided to leave it a couple of days before contacting BT. Later that day though I received three letters. One saying my DD had been cancelled as discussed, and two others saying my DD had been set up to be paid 28th of every month starting 28th May for the amount £104!
Before I had chance to call BT someone UK based called me to ask did I want to set up my DD as I had no payment plan set up. By this point I'd more than had enough and told her I had one email and two letters clearly saying my DD was set up and the only reason she'd be calling to ask me to do this would be if BT had cancelled the DD themselves. I refused to set up the DD yet again and she put me through to India based billing to discuss what was happening. I was told a DD wasn't set up on my account, that I couldn't set one up unless I paid my bill in full and that line restrictions are due to come into place on 29th May if the bill isn't paid in full.
Today my BT online account shows no DD set up. However my bank shows the new DD is in fact active. I have no idea when BT will take money, or for how much. I don't know what to do, do I cancel the DD and just pay all future bills in full when they come in and in doing so be penalised by BT for not paying by DD? Or do I just leave it and hope they finally get it right? Bearing in mind I've had two letters saying they're going to take £104 and an email saying £60 I can't see that happening.
It appears not one BT department speaks to the other, half the calls aren't logged and nobody at BT listens to the customer. I have spoken to Ofcom about this and they've advised me to give BT one more chance to sort this out and then go to the Ombudsman. I've just come across the forums and so am giving this a try to see if I can get any joy here.
At some point during all this I spoke to somebody UK based who told me to send my bank charge letters to BT which I have done but as yet have heard nothing in return! I've lost track of how many people I've spoken to and am at my wits end with it all.
Solved!
Go to Solution.

I'm even more concerned now after hearing back regarding my initial post. Apparently any cancellations or changes are showing as done by me using the self help platform on my BT account. This isn't the case. The actions carried out on certain dates listed on the email I received were all carried out by BT over the phone and not myself. I didn't even know it was possible to cancel a direct debit using the BT website. I thought it had to be cancelled at the bank and then a phone call to BT. I was logged onto my BT account while the phone calls were taking place but any action was carried out by BT and not myself.
BT are insisting I have no DD set up. Yet it clearly shows on my bank account that there is an active DD for BT. To confirm that, I've spoken to my bank today who have verified there is most definitely a DD set up to pay BT on the bank account. They've double checked the account number with me and it's definitely for my BT account. The bank are sending me a letter confirming it's an active DD for me to include all other details for the Ombudsman because I really feel this needs fetching to their attention.
To be fair to the person who has replied I have been told I can pay a small amount and set the DD up rather than pay in full or face restrictions. But despite BT's insistence that I have no DD set up my bank clearly states I have. I'm now going to have to cancel the DD that BT are sure isn't active and set it up again.
Incidentally the monthly payments I'm to make are £45 - less than the £60 and a lot less than the £104 previously mentioned! So on one hand I will have a satisfactory conclusion but on the other I have to still cancel a "none existent" existing DD, set a new one up and am out of pocket on bank charges caused by BT trying to take payment on the wrong date. I then have to trust they'll not do the same thing again.......
It's all like a stupid joke that's just not funny.

At wit's end with printing

I am begging for some help here. I have read everything I can find on printing within Aperture. The best guides appear to be published by Apple, and so I have followed those. I also have a couple of books that I use as well. I have a long history of successful printing on a pc so this is very frustrating for me.
I calibrate my monitor (iMac) with Gretag EyeOne Display2 hardware. I have used the recommended 2.2 gamma setting, the 6500K, and 120 luminance. I use a profile for my paper. Color management in my printer drive is off. On my pc, the profile was spot-on. I have yet to print a "spot-on" photo within Aperture.
I just tried a beautiful shot of two girls (both gorgeous green eyes on my monitor). The print is dark as heck and colors are totally off. I need to print these for a project that is due soon. I am at my wit's end.
Can someone help me? I am starting to get a bit desparate, as the paper and ink-wasting is costing me a ton of money. I will be forever grateful if someone can point me in a direction that will help. Not sure where else to go from here.

it's a long reply, but bare with me. i hope this is of some help for you.
the colors are still black/brown (when they should be blue, for instance).
the colors are still black/brown??? does the print look like it was almost flooded with ink that you can't quite make out what you've printed, or that where it's suppose to be blue it's black/brown in color?
when an image prints very dark, i can only assume that somewhere in the set-up color management is happening twice.
go to this link, http://files.support.epson.com/htmldocs/r220_/r220__rf/softx3.htm and then scroll down to Color Management section. note the screen capture for the Stylus Photo R220 print dialogue. i know you've already checked, but would you check again to make sure that your setting is not the same as in the screen capture. that is Off (No Color Adjustment) is the only option you want selected.
(one more thing that you could double check, and this is going to sound very absurd, because it's most probably not possible. would you check to see if the ink cartridges are where they are supposed to be, and that they're the right color? if you have printed with these same ink cartridges without any color problems on your pc, then it rules out misinstalled or mislabled ink cartridges.)
by the way, dale's suggestion is the right direction. you want to put aside (remove) custom profiles and other existing profiles and use only what the R220 driver installs by default.
meanwhile, for the purpose of meeting your deadline, i suggest that you make your prints with what have worked for you. after you've taken care of that, you can continue with your current Color Management issue.
one more thing. it's not your imagination, there is very little information about color management and printing in Aperture.
Mac OS X (10.4.7)

At my wit's end with Microsoft Exchange! Please Help!

Here's the scenario:
Purchased a 3G iPhone on Sunday and I am trying to sync to my corporate outlook e-mail through Microsoft Exchange. If I don't get this working soon, I am returning it because I am running out of patience and I need my work e-mail.
Important Fact: I previously used a Palm Treo that also used ActiveSync. Two minute easy set-up and worked FLAWLESSLY. So the issue is NOT the server from what I understand.
I used the same exact settings for the iPhone and when I try to add the account, I get this message "Exchange account verification failed".
I have tried:
adding /exchange after the server name.
adding /exchange/ after the server name.
disabling SSL. enabling SSL.
adding the domain name in the optional domain field.
adding my user name as domain\username.
I am being cap sensitive.
NOTHING has worked. I have reset, restored, etc, etc.
One interesting thing I noticed is that on my desktop, I can go to internet explorer and type in the server name https://xxxx.domain.com/exchange and I get outlook web access. When I try the same with Safari through the phone, I get "Safari can not connect because it can not establish a secure connection with the server".
Is this connected with my other issue?
Thank you for any ideas/ input.
- Julie

The following steps should work if everything on your Exchange server is configured properly.
All on your iPhone:
Go to Settings
Go to Mail, Contacts, Calendars
Choose Add Account...
Choose Exchange
Enter Email address
Enter username NOTE: be sure to use domain.local\username or domain\username(be sure to use the back slash)
Enter your password
Press Next
Okay, your iPhone at this point is going to attempt to connect to the mail server, but it will fail twice - after each failure, select Accept. After the 2nd failure, you will be brought back to the set up page, but you should now see the field Server
Enter the name of your mail server (typically mail.domain.com) into the Server field and select Next
At this point, the iphone should connect to the server, and then you will be prompted for what you would like to sync up in Exchange. You have 3 options - Mail, Contacts, and Calendar.

At Wit's End with HP LaserJet M1522 Multifunction device

Hi, About a month ago I started to notice that my LaserJet M1522 would lose connection with my computer whenever I shut down for the night. I was able to remedy this by turning the device on and off. Just this weekend, I started to notice that the device is still losing connection when the computer when I shut down, and possibly during my worksession. Not only am I not able to print when the printer is "down," but the scan, copy and fax functionality are also disabled. The device is not throwing any errors that I can see. The status window on the device does go dark when it is not working - but the "Ready" light stays on.
I just downloaded the HP patch that is supposed to fix the connection problem between the device and computer, but it doesn't appear to work.
I had reloaded my operating system, reinstalled the HP software from the disk and installed all HP updates communicated from the Web.
Any suggestions?

Hi, About a month ago I started to notice that my LaserJet M1522 would lose connection with my computer whenever I shut down for the night. I was able to remedy this by turning the device on and off. Just this weekend, I started to notice that the device is still losing connection when the computer when I shut down, and possibly during my worksession. Not only am I not able to print when the printer is "down," but the scan, copy and fax functionality are also disabled. The device is not throwing any errors that I can see. The status window on the device does go dark when it is not working - but the "Ready" light stays on.
I just downloaded the HP patch that is supposed to fix the connection problem between the device and computer, but it doesn't appear to work.
I had reloaded my operating system, reinstalled the HP software from the disk and installed all HP updates communicated from the Web.
Any suggestions?

At my wit's end with ATT UVerse and Time Capsule

I'm going to try this one last thread before I return all my UVerse stuff and go back to a simple Comcast modem. I have a Time Capsule, model A1409, and just got ATT U-Verse, model 3801HGV. I have searched the Apple community and any online website I can find that gives information about how to make the two work together and I have nothing but flashing amber. Airport Utility keeps saying the ethernet is unplugged (which the cable is plugged in from the modem to the TC), no DNS servers, and no internet connection. I have disabled the wireless function on the modem/router. I have put the Time Capsule in Bridge mode. I have rebooted everything. I have reset the TC three times. I have clicked on "DMZPlus mode". I've even enabled detection of router-behind-router conditions. I took the Time Capsule into Apple and it fired up right away, so no issues with the ethernet port. I can connect my PC to the ATT router and get internet access. No matter what I do, I still have flashing amber on my TC. Any last words of advice before I return everything from ATT?

If you want to run a test.. and that is all it will be..
I think I said the best way is to get a cheap fast ethernet switch and put it in between the two devices.. not everything in the ethernet world works.. it seldom fails now but it does fail at time.
If you are not interested in buying or borrowing a switch.. then you can do something to help in the TC interface.
This might only be available if you use 5.6 utility.. at least I have never done it via v6.
You will need to put the TC back into router mode. So start with another factory reset.
step 1 (only required if both units use same IP range).
And if the uverse modem is running 10.x.x.x IP then to give this the best shot, change the TC over to 192.168.1.x ip range. You do this by changing the DHCP Beginning Address from 10.0 to 192.168 in the picture below. If your uverse uses 192.168.x.x already ignore this step.
Step 2.
Check now that ethernet is still not working. If not go to the setup page for wan connection and change the WAN speed. Remember the TC must be plugged wan to uverse LAN port.
The only control offered is for WAN port to fix the speed. Change it down to 100Mbps/Full duplex.
Update the TC.
No luck, swap down to 10Mbps/Half-duplex ie the slowest possible. update the TC and see if it connects.
If it fails then there is something seriously wrong. And I doubt it will ever work.
If it happens to work at 100mbps/full duplex.. that is fast enough to cause no problems.. 10mbps is not.
I would either give up using the one item or the other.. but you do not want to keep this mode.. this is double NAT and we did it to test only.. success means the ethernet is failing to communicate correctly and go back and buy the switch I suggested.. fast ethernet.. small 5 port and it should fix it.

At wit's end with Comcast email

I have posted this here and on other forums. I cannot send email with my Comcast email account using MacMail. I have spent an hour with Comcast support chat and they say it is an Apple problem. Folks on here tell me it is a Comcast problem. I have tried all of the setting recommended to me and nothing works. I thought it might be a problem with Mavericks, but it worked for the first four months I was using Mavericks - then stopped working. Recently updated to Yosemite and the problem is still there.
Comcast keeps saying that they cannot authenticate the outgoing mail server. I have tried changing port numbers as per some suggestions. I have deleted the account and started over. I have changed my password with Comcast. I keep getting David (the name of my Comcast account) as David (Offline). Nothing works.
Thanks for any help.

Hi: Thank you very much for the rapid come back, most appreciated.
Hi Dan
A wild guess. Can it be so that those clips are
recorded in Your Camera with
the sound set to 12-bit (often factory/default set).
Should be 16-bit
I'll check the camera for that, but the same camera was used in all the clips and only two or three were missing audio when exported.
Try to extract the missing sounds from each clip and
redo a disk image in
iDVD and see if the sound is back.
That sounds like a great diagnostic and should be far less time consuming than burning a DVD.
Thanks for the hints.
Dan Page
Yours Bengt W

Internal Mic not Working, external mic quits arbitrarily, I'm at wit's end!!!!

Hey kids!
The Computer: Toshiba Satellite A355D-S69221
The Program: 32 Bit Windows Vista
The issue: Internal Mic not recognized, external mic quits midway through conversation, Realtek Digital output not plugged in.
So being the smart guy I am, a few weeks back I decided to do the smart thing and delete all the speech recognition software off this thing. I don't need it, so wth.
Now, my internal mic quit. I reinstalled the software, rolled back drivers, deleted drivers to rebuild the driver stack, did a BIOS update, did the GTA ViceCity cheatcode start (unplug everything hold power key 30 seconds, reboot, f2 to enter bios, f9 to update, f10 to save), and nothing.
I did notice that when I had the Realtek Digital Output set as standard, my mic jack was illuminated by a red LED, and the Realtek HD manager wouldn't pop up when I plug something in.
The last irritating part is that I will talk to my wife via vo/ip, the external mic I am using will just quit mid conversation, and I have to reload a driver to get it to work again. I am at my wit's end with this thing, can anyone help? The last thing I am goign to do is another system restore from an earlier date than I used before. Does anyone have any other hints/clues/ideas?
KFD

Thanks Jeff. No this isn't some kind of emergency so no one really minds my tinkering until it does get back up.
OK, I got it now. This is what my cyrus.conf looks like. It doesn't look like there's anything wrong with it...
# standard standalone server implementation
START {
# do not delete this entry!
recover cmd="ctl_cyrusdb -r"
# this is only necessary if using idled for IMAP IDLE
# idled cmd="idled"
# UNIX sockets start with a slash and are put into /var/imap/socket
SERVICES {
# add or remove based on preferences
imap cmd="imapd" listen="imap" prefork=0
imaps cmd="imapd -s" listen="imaps" prefork=0
pop3 cmd="pop3d" listen="pop3" prefork=0
pop3s cmd="pop3d -s" listen="pop3s" prefork=0
sieve cmd="timsieved" listen="sieve" prefork=0
# at least one LMTP is required for delivery
lmtp cmd="lmtpd" listen="lmtp" prefork=0
lmtpunix cmd="lmtpd" listen="/var/imap/socket/lmtp" prefork=0
# this is only necessary if using notifications
# notify cmd="notifyd" listen="/var/imap/socket/notify" proto="udp" prefork=1
EVENTS {
# this is required
checkpoint cmd="ctl_cyrusdb -c" period=30
# this is only necessary if using duplicate delivery suppression
delprune cmd="ctl_deliver -E 3" at=0400
# this is only necessary if caching TLS sessions
tlsprune cmd="tls_prune" at=0400
LIMITS {
imaplimit value=0
But yet it insists with the message: relay=cyrus, delay=239180, status=deferred (temporary failure. Command output: couldn't connect to lmtpd: No such file or directory_ 421 4.3.0 deliver: couldn't connect to lmtpd_ )
when I try to send a message through the server. Could this be a permissions thing? I've fixed the permissions a lot of times and nothing seems to get changed...
Again, thanks for everyone's help. I'm sure this is something dumb that I'm just missing but since I'm not familiar enough with the system it's hard for me to figure out what that is!

Hi, i am having an issue with a basic motion scroll effect. I already watched and read every tutorial out there regarding this topic and even tried the adobe chat support, but the guy on the other end of the line disconnected me-, probably he didn't unde

Hi, i am having an issue with a basic motion scroll effect.
I already watched and read every tutorial out there regarding this topic and even tried the adobe chat support, but the guy on the other end of the line disconnected me…, probably he didn't understand what i wanted from him because english is not my native language, so a will try to be very, very clear about this one..
please note, that i am new to muse, this is my first project ever.
my idea is as following:
when the customer comes to our companies site, he just sees our logo on a white Background. the logo consists of, say, four elements. when the customer scrolls down, the logo starts to disassamble: first the first part of the logo flies out the left side of the site, then the second part of the logo vanishes down, then the third part of the logo flies to the right, then the fourth part of the logo flies to the top and out of the customers view. given what i have seen, it is possible to do that….
so…..
now i have the four parts of my logo imported as png files into muse and assembled them in design view to build our companies logo. I select every one of the four parts and go into the scroll effects tab left beside the layers tab. first i enter the same values for every one of the four parts: initial motion: 0x and 0x again for the left and right motion; key position ( t-handle) : 0px; final motion: 0x and 0x again for the left and right value.
now i hit "preview".: the logo is "pinned" at the correct position, i can scroll but the logo stays where it is. so far so good….
now i select all the four elements again and go to the scroll effecs tab. at "final motion", i click the down arrows and enter 1x. I hit Preview…
when i am scrolling down the WHOLE logo goes down…. so far so good.
NOW i want the first part of the logo to go down, THEN the second part to go left, THEN the third part to go up, THEN the fourth part to go right.
so i select ONLY the first part, go to the scroll motion tab, at "final motion" i click the left arrows, then i enter 1x.( the up-down value, i set to 0 again).. i hit Preview…
the first part of the logo goes left as soon as i start scrolling, the other three parts still go down at the same time…
NOW i want the second part of the logo to start moving, when the first part has left the scene, not at the same time as the first part.
SO I SELECT THE SECOND PART AND DRAG ITS T-HANDLE (KEY POSITION) DOWN TO, LETS SAY, 200PX. SO IT STARTS MOVING ONLY AFTER THE CUSTOMER HAS REACHED THAT POINT, RIGHT?
BUT WHEN I PREVIEW THAT ****, THE LOGO IS NOT TOGETHER ANYMORE, THE SECOND PART IS FLOATING ANYWHERE ELSE BUT WHERE IT SHOULD BE…..WTFF????
short: when i move the t handle, the initial position of the object changes. thats what i said to the adobe employee, but he said, that thats the expected behavior….
but if thats so, how can i have my four parts correctly together, so they form my logo, but with different t handles, so that they all start to move at different times??
Pleeease help me, i am dying of frustration here…..:( that behavior cant be right, right?
Thanks so much to everyone who actually reads this post and tries to help…….
All the best,
Niki Lapan

Thank you so much for helping,
But i really wonder how you did that. did you always switch between design view and preview view, then change the key position for 2px then switch back, to align the four letters? because i imagine that can get really frustrating, if you have a logo consisting of 58 parts instead of 4!:)
Anyway thank you very much for your time and effort!!!!

Help with the error message that ADE is not allowed to copy a book onto my Nook. I have tried authorizing and unauthorizing many times--at wits end with this issue.

Help with the error message that ADE is not allowed to copy a book onto my Nook. I have tried authorizing and unauthorizing many times--at wits end with this issue.

I too am having the same problem. I have a new hard drive that was imaged from the old one and I'm trying to side load a book to my Nook Simple Touch.. I first installed ADE 4 then borrowed and downloaded a book from Overdrive. I tried a few times to delete and reauthorize both the computer and the Nook and each time I get an authorization error when I try to side load the book. I then found on the Nook forum that the Simple Touch and ADE 4 don't get along. So I uninstalled ADE 4 and installed ADE 3.
I then followed this recommended procedure found on the forum: I deleted the Digital Editions folder from my Nook, launched ADE 3 and authorized the computer, then connected the Nook. For a few seconds, hovering the mouse over the setting icon for the Nook displayed everything on the context menu grayed out. But then it showed the context menu and I was able to display the Nook's authorization, which was the same as the computer's. Still get the same error side loading the book. Deleting and reauthorizing doesn't help. And the Digital Editions folder is still missing from the Nook.

Your computer appears to be correctly configured, but the device or resource (DNS server) is not responding [and I'm at my wit's end!]

I originally posted this question to the community section and was advised to post it here. Please bear with me as this will be a long post. I'm including the scenarios involving this reoccurring issue, the trouble shooting steps I've already
taken and the results of several diagnostic tools and logs.
I have a Sony VAIOS VPCEBB33FM lap top since 2011. I have had this issue on an off for a long time. I'm at my wit's end. Any new insights or suggestions would be greatly appreciated.
Scenario Details
1) Some times it's on and off through out the day, sometimes it won't work all day, and once in a while it will work fine for the entire day.
2) I've had this issue across several wireless services, Clear Network accessed with WiMax, Library Wi-fi, Comcast cable internet using wireless router and Wi-fi, and Comcast Xfinity Wi-Fi, to name a few examples.
3) Other devices in the household or library will work with no problems such as my smart phone or my roommates' laptops or desktop computers.
4) Once in a while, the built-in wireless adapter is not found and I have to reinstall the driver. Also the diagnostic tool has had to reset my adapter on an increasing basis.
5) I had my hard drive replaced in December 2014 and my system restored from the System Restore disks that came with it when I bought the laptop. Even though I've been online on an infrequent basis it worked just fine for a while. Now that
I've been online a bit more I'm having the same issues again.
Below are my attempts at trouble shooting so far but I still have not been able to consistently resolve my DNS issues
1) Restarting my adapter
2) Turning off my laptop and removing the power supply for 5-10 minutes before turning it back on.
3) Using the IP Config in Command Prompt
     ipconfig /flushdns
   ipconfig /registerdns
   ipconfig /release
     ipconfig /renew
4) Using the NetSh reset in Command Prompt and restarting my laptop
     netsh int ip reset c:\resetlog.txt
     netsh winsock reset
     ipconfig /flushdns
     [restart laptop]
5) Configuring the TCP/IP in several settings
    Select Internet Protocol Version 4 (TCP/IPv4), and then click Properties.
    I have used the following settings:
       a) Obtain an DNS server address automatically
       b) OpenDNS
           208 67 222 222
           208 67 220 220
       c) Google DNS
           8 8 8 8
           8 8 4 4
6) Updating the driver for my Intel Centrino(R) Advanced-N 6250 AGN and Intel Centrino(R) WIMAX 6250 from the Intel website previous having my laptop wiped clean in 2014. It still did not resolve the issue. My laptop
manufacturer as not come up with an driver update for my adapter since 2010. I haven't tried to update the adapter driver from Intel's website since having my laptop repaired due to the fact that Intel strongly recommending using the manufacturer's updates
instead and frankly it didn't make much of a difference when I did it the first time.
7) The last one I've tried as of today is going into Services and changing the start up type to automatic for the following:
       Computer Browser [changed from manual to automatic]
       DHCP Client [already set to automatic]
       DNS Client [already set to automatic]
       Network Connections [already set to automatic]
       Network Location Awareness [changed from manual to automatic]
       Remote Procedure Call (RPC) [already set to automatic]
       Server [already set to automatic]
       TCP/IP Netbios helper [already set to automatic]
       Workstation [already set to automatic]
...and I'm still having DNS issues.
My only guessing are that my laptop came with a lemon adapter that needs to be replaced, some advanced setting(s) that I'm not aware off, or my firewall/anti-virus is interfering. I've used Symmantic Anti-virus and Firewall in the past and currently
Avast Anti-Virus with Microsoft Network Firewall. I've had DNS issues with both anti-virus/firewall set ups.
Below are the results from the diagnostics and tests that I've ran.
Windows Network Diagnostics
Your computer appears to be correctly configured, but the device or resource (DNS server) is not responding Detected Detected
Contact your network administrator or Internet service provider (ISP) Completed
Windows can't communicate with the device or resource (DNS server). The computer or service you are trying to reach might be...
Details about network adapter diagnosis:
Network adapter Wireless Network Connection driver information:
   Description . . . . . . . . . . : Intel(R) Centrino(R) Advanced-N 6250 AGN
   Manufacturer . . . . . . . . . : Intel Corporation
   Provider . . . . . . . . . . . : Intel
   Version   . . . . . . . . . . . : 13.2.1.5
   Inf File Name . . . . . . . . . : C:\Windows\INF\oem17.inf
   Inf File Date . . . . . . . . . : Monday, June 14, 2010 9:05:44 AM
   Section Name . . . . . . . . . : Install_MPCIEX_GEN_6250_AGN_2x2_HMC_WIN7_64_MOW
   Hardware ID . . . . . . . . . . : pci\ven_8086&dev_0087&subsys_13018086
   Instance Status Flags . . . . . : 0x180200a
   Device Manager Status Code . . : 0
   IfType . . . . . . . . . . . . : 71
   Physical Media Type . . . . . . : 9
Informational Diagnostics Information (Wireless Connectivity)
Details about wireless connectivity diagnosis:
Information for connection being diagnosed
Interface GUID: 70a0781d-6329-45e4-8d7c-34aeca294c39
Interface name: Intel(R) Centrino(R) Advanced-N 6250 AGN
Interface type: Native WiFi
Connection incident diagnosed
Auto Configuration ID: 1
Connection ID: 1
Connection status summary
Connection started at: 2015-03-07 19:57:14-186
Profile match: Success
Pre-Association: Success
Association: Success
Security and Authentication: Success
List of visible access point(s): 22 item(s) total, 22 item(s) displayed
        BSSID       BSS Type PHY   Signal(dB)   Chnl/freq    SSID
60-02-92-C6-D3-E8   Infra   <unknown>   -62       11   HOME-C7D4-2.4
60-02-92-A1-75-E0   Infra   <unknown>   -58       6   HOME-B917-2.4
00-1D-D5-D5-34-F0   Infra   <unknown>   -73       6   HOME-34F2
60-02-92-A1-75-E1   Infra   <unknown>   -58       6   (Unnamed Network)
06-1D-D5-D5-34-F0   Infra   <unknown>   -78       6   xfinitywifi
C4-27-95-C9-C4-2D   Infra   <unknown>   -57       1   HOME-C42D
02-1D-D5-D5-34-F0   Infra   <unknown>   -74       6   (Unnamed Network)
00-0D-97-07-E0-79   Infra   g   -75       6   (Unnamed Network)
00-1D-CF-2A-44-C0   Infra   <unknown>   -86       6   HOME-44C2
02-1D-CF-2A-44-C0   Infra   <unknown>   -86       6   (Unnamed Network)
F8-E4-FB-3C-87-A2   Infra   <unknown>   -89       6   YVNM7
06-1D-CF-2A-44-C0   Infra   <unknown>   -87       6   xfinitywifi
0C-F8-93-7A-13-50   Infra   b   -87       6   PKennedy
06-F8-93-7A-13-50   Infra   b   -89       6   xfinitywifi
02-F8-93-7A-13-50   Infra   b   -87       6   (Unnamed Network)
E0-88-5D-C8-A9-DC   Infra   <unknown>   -80       1   HOME-A9DC
E2-88-5D-C8-A9-DD   Infra   <unknown>   -79       1   (Unnamed Network)
16-CF-E2-43-0B-30   Infra   <unknown>   -88       1   xfinitywifi
60-02-92-F0-A8-C0   Infra   <unknown>   -90       11   HOME-96A6-2.4
60-02-92-C6-D3-E9   Infra   <unknown>   -63       11   (Unnamed Network)
02-1D-D4-EB-87-00   Infra   <unknown>   -88       11   (Unnamed Network)
06-1D-D4-EB-87-00   Infra   <unknown>   -88       11   xfinitywifi
Connection History
Information for Auto Configuration ID 1
List of visible networks: 13 item(s) total, 13 item(s) displayed
BSS Type PHY   Security   Signal(RSSI)   Compatible   SSID
Infra   <unknown>   Yes       63   Yes       HOME-C7D4-2.4
Infra   <unknown>   Yes       70   Yes       HOME-B917-2.4
Infra   <unknown>   Yes       43   Yes       HOME-34F2
Infra   <unknown>   Yes       70   Yes       (Unnamed Network)
Infra   <unknown>   No       40   Yes       xfinitywifi
Infra   <unknown>   Yes       71   Yes       HOME-C42D
Infra   g   No       43   Yes       (Unnamed Network)
Infra   <unknown>   Yes       28   Yes       HOME-44C2
Infra   <unknown>   Yes       20   Yes       YVNM7
Infra   b   Yes       21   Yes       PKennedy
Infra   <unknown>   Yes       33   Yes       HOME-A9DC
Infra   <unknown>   Yes       35   Yes       (Unnamed Network)
Infra   <unknown>   Yes       16   Yes       HOME-96A6-2.4
List of preferred networks: 3 item(s)
   Profile: xfinitywifi
    SSID: xfinitywifi
    SSID length: 11
    Connection mode: Infra
    Security: No
    Set by group policy: No
    Connect even if network is not broadcasting: No
    Connectable: Yes
   Profile: HTC Portable Hotspot 9F50
    SSID: HTC Portable Hotspot 9F50
    SSID length: 25
    Connection mode: Infra
    Security: Yes
    Set by group policy: No
    Connect even if network is not broadcasting: No
    Connectable: No
     Reason: 0x00028002
   Profile: belkin.332
    SSID: belkin.332
    SSID length: 10
    Connection mode: Infra
    Security: Yes
    Set by group policy: No
    Connect even if network is not broadcasting: No
    Connectable: No
     Reason: 0x00028002
Information for Connection ID 1
Connection started at: 2015-03-07 19:57:14-186
Auto Configuration ID: 1
Profile: xfinitywifi
SSID: xfinitywifi
SSID length: 11
Connection mode: Infra
Security: No
Pre-Association and Association
   Connectivity settings provided by hardware manufacturer (IHV): No
   Security settings provided by hardware manufacturer (IHV): No
   Profile matches network requirements: Success
   Pre-association status: Success
   Association status: Success
    Last AP: 06-1d-d5-d5-34-f0
Security and Authentication
   Configured security type: Open
   Configured encryption type: None
   802.1X protocol: No
   Key exchange initiated: Yes
    Unicast key received: No
    Multicast key received: No
   Number of security packets received: 0
   Number of security packets sent: 0
   Security attempt status: Success
Connectivity
   Packet statistics
    Ndis Rx: 2068
    Ndis Tx: 2543
    Unicast decrypt success: 0
    Multicast decrypt success: 0
    Unicast decrypt failure: 0
    Multicast decrypt failure: 0
    Rx success: 3954
    Rx failure: 0
    Tx success: 537
    Tx failure: 4
    Tx retry: 2
    Tx multiple retry: 2
    Tx max lifetime exceeded: 0
    Tx ACK failure: 18
   Roaming history: 0 item(s)
InformationalDiagnostics Information (Wireless Connectivity)
Details about wireless connectivity diagnosis:
For complete information about this session see the wireless connectivity information event.
Helper Class: Auto Configuration
Initialize status: Success
Information for connection being diagnosed
Interface GUID: 70a0781d-6329-45e4-8d7c-34aeca294c39
Interface name: Intel(R) Centrino(R) Advanced-N 6250 AGN
Interface type: Native WiFi
Result of diagnosis: There may be problem
Network Connection details from Command Prompt (some info hidden for security reasons)
Connection-specific DNS Suffix:
Description: Intel(R) Centrino(R) Advanced-N 6250 AGN
Physical Address: ‎00-23-15-54-19-B8
DHCP Enabled: Yes
IPv4 Address: 192.168.X.XX
IPv4 Subnet Mask: 255.255.XX.X
Lease Obtained: Saturday, March 07, 2015 7:57:14 PM
Lease Expires: Saturday, March 07, 2015 8:24:44 PM
IPv4 Default Gateway: 192.168.X.X
IPv4 DHCP Server: 192.168.X.X
IPv4 DNS Servers: 75.75.75.75, 75.75.76.76
IPv4 WINS Server:
NetBIOS over Tcpip Enabled: Yes
Link-local IPv6 Address: fe80::b8de:3ac9:e166:XXX%XX
IPv6 Default Gateway:
IPv6 DNS Server:
Results of Ping and Trace Route in Command Prompt
Microsoft Windows [Version 6.1.7601]
Copyright (c) 2009 Microsoft Corporation. All rights reserved.
C:\Windows\system32>ping 127.0.0.1
Pinging 127.0.0.1 with 32 bytes of data:
Reply from 127.0.0.1: bytes=32 time<1ms TTL=128
Reply from 127.0.0.1: bytes=32 time<1ms TTL=128
Reply from 127.0.0.1: bytes=32 time<1ms TTL=128
Reply from 127.0.0.1: bytes=32 time<1ms TTL=128
Ping statistics for 127.0.0.1:
    Packets: Sent = 4, Received = 4, Lost = 0 (0% loss),
Approximate round trip times in milli-seconds:
    Minimum = 0ms, Maximum = 0ms, Average = 0ms
C:\Windows\system32>ping www.youtube.com
Pinging youtube-ui.l.google.com [173.194.121.6] with 32 bytes of data:
Reply from 173.194.121.6: bytes=32 time=24ms TTL=55
Reply from 173.194.121.6: bytes=32 time=19ms TTL=55
Request timed out.
Request timed out.
Ping statistics for 173.194.121.6:
    Packets: Sent = 4, Received = 2, Lost = 2 (50% loss),
Approximate round trip times in milli-seconds:
    Minimum = 19ms, Maximum = 24ms, Average = 21ms
C:\Windows\system32>ping 74.125.239.34
Pinging 74.125.239.34 with 32 bytes of data:
Request timed out.
Request timed out.
Reply from 74.125.239.34: bytes=32 time=3286ms TTL=50
Request timed out.
Ping statistics for 74.125.239.34:
    Packets: Sent = 4, Received = 1, Lost = 3 (75% loss),
Approximate round trip times in milli-seconds:
    Minimum = 3286ms, Maximum = 3286ms, Average = 3286ms
C:\Windows\system32>ping www.hotmail.com
Pinging dispatch.kahuna.glbdns2.microsoft.com [65.55.157.204] with 32 bytes of data:
Reply from 65.55.157.204: bytes=32 time=111ms TTL=237
Request timed out.
Request timed out.
Reply from 65.55.157.204: bytes=32 time=1537ms TTL=237
Ping statistics for 65.55.157.204:
    Packets: Sent = 4, Received = 2, Lost = 2 (50% loss),
Approximate round trip times in milli-seconds:
    Minimum = 111ms, Maximum = 1537ms, Average = 824ms
C:\Windows\system32>ping 207.46.11.236
Pinging 207.46.11.236 with 32 bytes of data:
Request timed out.
Request timed out.
Request timed out.
Request timed out.
Ping statistics for 207.46.11.236:
    Packets: Sent = 4, Received = 0, Lost = 4 (100% loss),
C:\Windows\system32>tracert www.youtube.com
Tracing route to youtube-ui.l.google.com [173.194.121.5]
over a maximum of 30 hops:
1    19 ms    13 ms    17 ms xfwsr12-nwca-01.sys.comcast.net [68.85.15.244]
2    13 ms    13 ms    27 ms ae-14-32767-ar03.newcastle.de.panjde.comcast.net [68.85.192.205]
3    20 ms    26 ms    21 ms he-5-10-0-0-cr01.ashburn.va.ibone.comcast.net [68.86.94.249]
4    18 ms    34 ms    22 ms he-0-13-0-0-pe07.ashburn.va.ibone.comcast.net [68.86.86.50]
5    19 ms    18 ms    18 ms 50-248-116-190-static.hfc.comcastbusiness.net [50.248.116.190]
6    35 ms    18 ms    18 ms 209.85.249.217
7    21 ms    19 ms    19 ms 72.14.233.93
8     *        *        *     Request timed out.
9     *     2509 ms   677 ms iad23s25-in-f5.1e100.net [173.194.121.5]
Trace complete.
C:\Windows\system32>tracert 74.125.239.34
Tracing route to nuq04s19-in-f2.1e100.net [74.125.239.34]
over a maximum of 30 hops:
1    54 ms    23 ms    12 ms xfwsr12-nwca-01.sys.comcast.net [68.85.15.244]
2    22 ms    19 ms    17 ms ae-14-32767-ar03.newcastle.de.panjde.comcast.net[68.85.192.205]
3    19 ms    19 ms    18 ms he-5-14-0-0-cr01.ashburn.va.ibone.comcast.net [68.86.166.121]
4    18 ms    18 ms    18 ms he-0-15-0-0-cr01.350ecermak.il.ibone.comcast.net[68.86.85.74]
5    19 ms    18 ms    22 ms 50-248-116-190-static.hfc.comcastbusiness.net [50.248.116.190]
6    22 ms    36 ms    19 ms 209.85.249.217
7    26 ms    23 ms    25 ms 209.85.143.112
8     *        *        *     Request timed out.
9     *        *        *     Request timed out.
10   972 ms     *        *     216.239.51.97
11   148 ms    97 ms    95 ms 216.239.46.241
12   324 ms   130 ms   432 ms 209.85.246.252
13     *        *        *     Request timed out.
14 1403 ms   101 ms   126 ms nuq04s19-in-f2.1e100.net [74.125.239.34]
Trace complete.
C:\Windows\system32>tracert www.hotmail.com
Tracing route to dispatch.kahuna.glbdns2.microsoft.com [65.55.157.144]
over a maximum of 30 hops:
1    13 ms    13 ms    25 ms xfwsr12-nwca-01.sys.comcast.net [68.85.15.244]
2    13 ms    15 ms    13 ms ae-14-32767-ar03.newcastle.de.panjde.comcast.net[68.85.192.205]
3    20 ms    19 ms    17 ms he-5-13-0-0-cr01.ashburn.va.ibone.comcast.net [68.86.95.145]
4    17 ms    20 ms    20 ms he-0-13-0-0-pe07.ashburn.va.ibone.comcast.net [68.86.86.50]
5    17 ms    18 ms    38 ms as8075-2-c.ashburn.va.ibone.comcast.net [173.167.58.82]
6    18 ms    18 ms    36 ms ae4-0.ash-96cbe-1a.ntwk.msn.net [207.46.36.172]
7     *        *        *     Request timed out.
8     *     2191 ms    35 ms ae0-0.atb-96cbe-1b.ntwk.msn.net [191.234.81.167]
9     *        *        *     Request timed out.
10     *        *        *     Request timed out.
11    86 ms    84 ms    84 ms ae4-0.lax-96cbe-1a.ntwk.msn.net [191.234.83.150]
12    86 ms    86 ms    87 ms ae9-0.by2-96c-1a.ntwk.msn.net [207.46.42.176]
13     *        *        *     Request timed out.
14     *        *        *     Request timed out.
15     *        *        *     Request timed out.
16     *        *        *     Request timed out.
17    87 ms    84 ms    85 ms origin.by173w.bay173.mail.live.com [65.55.157.144]
Trace complete.
C:\Users\C.Cunningham>tracert 207.46.11.236
Tracing route to origin.by181w.bay181.mail.live.com [207.46.11.236]
over a maximum of 30 hops:
1    16 ms    16 ms    19 ms xfwsr12-nwca-01.sys.comcast.net [68.85.15.244]
2    18 ms    13 ms    13 ms ae-14-32767-ar03.newcastle.de.panjde.comcast.net[68.85.192.205]
3    21 ms    19 ms    21 ms he-5-12-0-0-cr01.ashburn.va.ibone.comcast.net [68.86.95.141]
4    18 ms    21 ms    18 ms he-0-13-0-0-pe07.ashburn.va.ibone.comcast.net [68.86.86.50]
5     *        *        *     Request timed out.
6     *        *        *     Request timed out.
7     *        *        *     Request timed out.
8     *        *        *     Request timed out.
9     *        *        *     Request timed out.
10     *        *        *     Request timed out.
11     *        *        *     Request timed out.
12     *        *        *     Request timed out.
13     *        *        *     Request timed out.
14     *        *        *     Request timed out.
15     *        *        *     Request timed out.
16     *        *        *     Request timed out.
17     *        *        *     Request timed out.
18     *        *        *     Request timed out.
19     *        *        *     Request timed out.
20     *        *        *     Request timed out.
21     *        *        *     Request timed out.
22     *        *        *     Request timed out.
23     *        *        *     Request timed out.
24     *        *        *     Request timed out.
25     *        *        *     Request timed out.
26     *        *        *     Request timed out.
27     *        *        *     Request timed out.
28     *        *        *     Request timed out.
29     *        *        *     Request timed out.
30     *        *        *     Request timed out.
Trace complete.
Results of Intel WiFi Manual Diagnostics
Test Name                 Test Result   Test Summary
Hardware Test           Passed        Wireless Hardware is enabled
Driver Test           Passed        Diver is loaded. NETwNs64 Version 13.3.0.24
Radio Test                  Passed       Radio is ON
Scan Test                   Passed       There are 25 Networks available to connect
Association Test        Passed       Associated
Authentication Test   Passed       Authenticated
Signal Test                Passed       Signal Quality: Poor
Ping Test                  Failed          No Reponse: default gateway, DHCP server
I hope this information is enough to get to the root of this problem once and for all. Please let me know if you any other information such as event logs or statistics.
Thanks in advance.

Results of Intel WiFi Event View Log (I deleted some lines since there were basically repeats of the same messages)
#Event Source Time
Error Severity    Domain
User      Description
45           EvtEngine
3/8/2015 20:40 Success
Connection         SYSTEM
iAMT - Failed to read Windows Events Log
46           S24EvMon
3/8/2015 20:41 Information
AppDriver
SYSTEM
Getting List of adapters.
47           S24EvMon
3/8/2015 20:41 Information
AppDriver
SYSTEM
Intel adapter(s) found.
156         S24EvMon
3/8/2015 20:47 Information
Driver    SYSTEM
AddToExclude 06:1d:d5:d5:34:f0 xfinitywifi 6 WEV_EXCLUDE_LIST_REASON_802_11_AUTH_FAILURE
157         S24EvMon
3/8/2015 20:47 Information
Driver    SYSTEM
ATC 06:1d:cf:2a:44:c0 xfinitywifi 6 RSSI=-88
158         S24EvMon
3/8/2015 20:47 Error
Driver    SYSTEM
AssociationFailure 06:1d:cf:2a:44:c0 xfinitywifi 6 CNCT_GENERAL_FAILURE
159         S24EvMon
3/8/2015 20:47 Information
Driver    SYSTEM
AddToExclude 06:1d:cf:2a:44:c0 xfinitywifi 6 WEV_EXCLUDE_LIST_REASON_802_11_ASSOC_FAILURE
160         S24EvMon
3/8/2015 20:47 Information
Driver    SYSTEM
ATC 06:1d:d5:d5:34:f0 xfinitywifi 6 RSSI=-79
161         S24EvMon
3/8/2015 20:47 Success
Driver    SYSTEM
RxAuthSuccess 06:1d:d5:d5:34:f0 6
162         S24EvMon
3/8/2015 20:47 Success
Driver    SYSTEM
RxAssocResp 06:1d:d5:d5:34:f0 6 -77
163         S24EvMon
3/8/2015 20:49 Information
TCP/IP SYSTEM
VoIP: Got link down - deleting flows .
164         S24EvMon
3/8/2015 20:49 Information
Driver    SYSTEM
ATC 06:1d:d4:eb:87:00 xfinitywifi 11 RSSI=-88
165         S24EvMon
3/8/2015 20:49 Error
Driver    SYSTEM
AssociationFailure 06:1d:d4:eb:87:00 xfinitywifi 11 CNCT_GENERAL_FAILURE
166         S24EvMon
3/8/2015 20:49 Information
Driver    SYSTEM
AddToExclude 06:1d:d4:eb:87:00 xfinitywifi 11 WEV_EXCLUDE_LIST_REASON_802_11_ASSOC_FAILURE
167         S24EvMon
3/8/2015 20:49 Information
Driver    SYSTEM
ATC 06:1d:d4:eb:87:00 xfinitywifi 11 RSSI=-89
168         S24EvMon
3/8/2015 20:49 Error
Driver    SYSTEM
AssociationFailure 06:1d:d4:eb:87:00 xfinitywifi 11 CNCT_GENERAL_FAILURE
169         S24EvMon
3/8/2015 20:49 Information
Driver    SYSTEM
AddToExclude 06:1d:d4:eb:87:00 xfinitywifi 11 WEV_EXCLUDE_LIST_REASON_802_11_ASSOC_FAILURE
170         S24EvMon
3/8/2015 20:49 Information
Driver    SYSTEM
ATC 06:1d:d4:eb:87:00 xfinitywifi 11 RSSI=-90
171         S24EvMon
3/8/2015 20:49 Error
Driver    SYSTEM
AssociationFailure 06:1d:d4:eb:87:00 xfinitywifi 11 CNCT_GENERAL_FAILURE
172         S24EvMon
3/8/2015 20:49 Information
Driver    SYSTEM
ATC 06:1d:d5:d5:34:f0 xfinitywifi 6 RSSI=-82
173         S24EvMon
3/8/2015 20:49 Success
Driver    SYSTEM
RxAuthSuccess 06:1d:d5:d5:34:f0 6
174         S24EvMon
3/8/2015 20:49 Success
Driver    SYSTEM
RxAssocResp 06:1d:d5:d5:34:f0 6 -81
175         S24EvMon
3/8/2015 20:50 Information
Driver    SYSTEM
AddToExclude 06:1d:d5:d5:34:f0 xfinitywifi 6 WEV_EXCLUDE_LIST_REASON_802_11_AUTH_FAILURE
176         S24EvMon
3/8/2015 20:50 Information
Driver    SYSTEM
ATC 06:1d:d5:d5:34:f0 xfinitywifi 6 RSSI=-79
177         S24EvMon
3/8/2015 20:50 Success
Driver    SYSTEM
RxAuthSuccess 06:1d:d5:d5:34:f0 6
178         S24EvMon
3/8/2015 20:50 Success
Driver    SYSTEM
RxAssocResp 06:1d:d5:d5:34:f0 6 -80
179         S24EvMon
3/8/2015 21:03 Information
Driver    SYSTEM
RoamTrigger 06:1d:d5:d5:34:f0 xfinitywifi 6 RSSI=-81 MisBcn=8 RSSITh=-85 Roam Other Reason
186         S24EvMon
3/8/2015 21:21 Information
General
SYSTEM
DeviceIoCtrlS24NDIS: (2) Failed to send OID 0xff100055 to driver. Error - 31
187
S24EvMon
3/8/2015 21:21 Information
General
SYSTEM
DeviceIoCtrlS24NDIS - Dot11ExtNicSpecificExtension failed (31)

Error while executing BBP_UPDATE_PORG Tr Code with ADD Option

Hi All,
I changed the Back end Vendor Master Data - Purchasing View (Example Accounting Number) and run the BBPUPDVD Tr code in SRM. The Business Partner (Vendor) data is updated correctly in SRM System from Back End System.
We have set of purchasing organisations like one local (SRM) Purchasing Organisation and respective Back end Purchasing Organisation (account number). When ever I run BBPUPDVD, the SRM system updates the backend vendor master data with back end purchasing organisation into SRM Standard tables. Then I am running BBP_UPDATE_PORG Tr code to have updated data into SRM Local Purchasing Organisation. I am receiving error message.
Example Scenario:
step 1: Present values in Vendor Master Vendor Number 100250, Purchaing Organisation : 1010 A/c Number: 100250-1010
and I changed the account number as 10025o-test for vendor 100250 and pur organisation 1010.
step 2: I run the BBPUPDVD in SRM System.
Step 3: I checked the values in BBPMAININT - vendor data (for backend vendor number 100250 and backend pur organisation - 1010). The SRM system replicates the values correct.
Step 4: I executed BBP_UPDATE_PORG and replaced the local (SRM) business partner (for local vendor number - 100250 and local purchasing organisation) - REPLACE Option. Then SRM replaces the SRM Business Partner (local) Data with Back end Vendor Master Data and also Back End vendor master data is deleted in SRM System. Now I have updated business partner details in SRM System as SRM Local an no SRM Back End Vendor Master Data in SRM System. This step is working fine.
Step 5: One more time I am executing BBP_UPDATE_PORG Tr code with Add option to have SRM Back End Details (in SRM System) from SRM Local Details (SRM System). Then the system is error message in SM13 Tr code.
Kind Note: There is no SRM Back End Vendor details in SRM System which I want to have with the help of executing BBP_UPDATE_PORG Tr code with Add option.
For analysis I went to ST22 (dump Analysis), the SRM gave an error message like:
Runtime Error          DYNPRO_SEND_IN_BACKGROUND
Date and Time          09/15/2008 10:56:58
ShrtText
     Screen output without connection to user.
What happened?
     Error in ABAP application program.
     The current ABAP program "SAPLBBP_PARTNER_MAINT" had to be terminated because
      one of the
     statements could not be executed.
     This is probably due to an error in the ABAP program.
Information on where terminated
    The termination occurred in the ABAP program "SAPLBBP_PARTNER_MAINT" in      "BBP_PORG_INSERT".
    The main program was "RSM13000 ".
    The termination occurred in line 59 of the source code of the (Include)      program "LBBP_PARTNER_MAINTU11"
    of the source code of program "LBBP_PARTNER_MAINTU11" (when calling the editor      590).
    The program "SAPLBBP_PARTNER_MAINT" was started in the update system.
   56
   57 * update database
   58   IF NOT LT_FRG0060_NEW[] IS INITIAL.
>>>>>     INSERT BBPM_BUT_FRG0060 FROM TABLE LT_FRG0060_NEW.
   60   ENDIF.
   61
   62   IF NOT LT_FRG0061_NEW[] IS INITIAL.
   63     INSERT BBPM_BUT_FRG0061 FROM TABLE LT_FRG0061_NEW.
   64   ENDIF.
Kindly guide me or provide solution.
We are in SRM 4.0 and ECC 5.0.
Thanks a lot in advance.
Regards,
Sudarsan
Edited by: KOYYA SUDARSANA NAIDU on Sep 15, 2008 9:09 PM
Edited by: KOYYA SUDARSANA NAIDU on Sep 17, 2008 8:46 PM

Hi All,
I changed the Back end Vendor Master Data - Purchasing View (Example Accounting Number) and run the BBPUPDVD Tr code in SRM. The Business Partner (Vendor) data is updated correctly in SRM System from Back End System.
We have set of purchasing organisations like one local (SRM) Purchasing Organisation and respective Back end Purchasing Organisation (account number). When ever I run BBPUPDVD, the SRM system updates the backend vendor master data with back end purchasing organisation into SRM Standard tables. Then I am running BBP_UPDATE_PORG Tr code to have updated data into SRM Local Purchasing Organisation. I am receiving error message.
Example Scenario:
step 1: Present values in Vendor Master Vendor Number 100250, Purchaing Organisation : 1010 A/c Number: 100250-1010
and I changed the account number as 10025o-test for vendor 100250 and pur organisation 1010.
step 2: I run the BBPUPDVD in SRM System.
Step 3: I checked the values in BBPMAININT - vendor data (for backend vendor number 100250 and backend pur organisation - 1010). The SRM system replicates the values correct.
Step 4: I executed BBP_UPDATE_PORG and replaced the local (SRM) business partner (for local vendor number - 100250 and local purchasing organisation) - REPLACE Option. Then SRM replaces the SRM Business Partner (local) Data with Back end Vendor Master Data and also Back End vendor master data is deleted in SRM System. Now I have updated business partner details in SRM System as SRM Local an no SRM Back End Vendor Master Data in SRM System. This step is working fine.
Step 5: One more time I am executing BBP_UPDATE_PORG Tr code with Add option to have SRM Back End Details (in SRM System) from SRM Local Details (SRM System). Then the system is error message in SM13 Tr code.
Kind Note: There is no SRM Back End Vendor details in SRM System which I want to have with the help of executing BBP_UPDATE_PORG Tr code with Add option.
For analysis I went to ST22 (dump Analysis), the SRM gave an error message like:
Runtime Error          DYNPRO_SEND_IN_BACKGROUND
Date and Time          09/15/2008 10:56:58
ShrtText
     Screen output without connection to user.
What happened?
     Error in ABAP application program.
     The current ABAP program "SAPLBBP_PARTNER_MAINT" had to be terminated because
      one of the
     statements could not be executed.
     This is probably due to an error in the ABAP program.
Information on where terminated
    The termination occurred in the ABAP program "SAPLBBP_PARTNER_MAINT" in      "BBP_PORG_INSERT".
    The main program was "RSM13000 ".
    The termination occurred in line 59 of the source code of the (Include)      program "LBBP_PARTNER_MAINTU11"
    of the source code of program "LBBP_PARTNER_MAINTU11" (when calling the editor      590).
    The program "SAPLBBP_PARTNER_MAINT" was started in the update system.
   56
   57 * update database
   58   IF NOT LT_FRG0060_NEW[] IS INITIAL.
>>>>>     INSERT BBPM_BUT_FRG0060 FROM TABLE LT_FRG0060_NEW.
   60   ENDIF.
   61
   62   IF NOT LT_FRG0061_NEW[] IS INITIAL.
   63     INSERT BBPM_BUT_FRG0061 FROM TABLE LT_FRG0061_NEW.
   64   ENDIF.
Kindly guide me or provide solution.
We are in SRM 4.0 and ECC 5.0.
Thanks a lot in advance.
Regards,
Sudarsan
Edited by: KOYYA SUDARSANA NAIDU on Sep 15, 2008 9:09 PM
Edited by: KOYYA SUDARSANA NAIDU on Sep 17, 2008 8:46 PM

Transport control program tp ended with error code 0211

Dear Experts,
I have a problem in doing the import after the client export was successfully done.
I am actaully tring to do a client import/export from the PRD server to DEV server.
On PRD the client is 900 and on the DEV the client is 240.
I have manually copied the transport requests created into the
/usr/sap/trans/cofiles and /usr/sap/trans/data folders to the same on the DEV server.
After coping them,
I have tried to add these transport requests to the DEV server queue, i get the following error message
Transport control program tp ended with error code 0211
Message no. XT200
Diagnosis
An error occurred when executing a tp command.
Command: ADDTOBUFFER RT2KT00014 RT1 pf=/usr/sap/trans/bin/T
Return code: 0211
Error text: no info about transport request found
Request: RT2KT00014
System Response
The function terminates.
Procedure
Correct the error and execute the command again if necessary.
After this I have tried to add the transports to the buffer at the OS level using the command
./tp pf=TPPARAM addtobuffer "RT2KT00014" RT1 U18 by going to the folder
/usr/sap/trans/bin
But it says that the tp is not found.
I have also checked the permissions for the TRANS folder, it has full access i.e 777
This is where i am struck, and the client has to be imported asap as the requirement for the SUPPORT TEAM is very urgent.
We are on AIX, Oracle 10G and ECC6
Thanks and regards
Harry

Dear Imtiaz,
Thanks for your quick fire reply...
The link helped me but it could not resolve my issue..
Infact i found it my self that the transport requests had to be given full FILE PERMISSIONS at the OS level
I logged in as ROOT
and changed directory to /usr/sap/trans/cofile and gave the command
chmod 777 RT00014.RT2 and
chmod 777 RX00014.RT2
and then went to STMS>SYSTEMS>Import View>Extras>Other requests--> Add ..
Here i added the request nos and then it added up in the queue and then i started the import.
Anyway thank you very for your reply..
Awareded points to you.
Thanks and regards
Harry...

Transport control program tp ended with error code 0247

Hi,
Our landscape is such that any transport request once released, gets imported to Q system immediately. However there is another system (another box REG - regression testing) to which I would like to import a request but the transport queue of REG system does not show the request. So I tried to explicitly add it to the queue but I get the following error message, 'Transport control program tp ended with error code 0247.
There doesn't seem to be a problem with data & CO files as the same request is in Q system and the changes are all transported successfully.
This request is a transport of copy that contains some ABAP code. (changes to the relevant package can be saved only in local requests therefore transport of copy is recommended to transport the changes).
The changes appear correctly in Q system but for REG system the request neither appears in the queue nor be added to it.
Can someone advise where the problem is.
Cheers,
KC

Hi
When the REG system is not in the system landscape, probably you may not have Data & Co files in that system & you need to have those files separately in the REG system path & then import it.
Do consult Basis team on this issue.
Thanks,
Murali.

At wit's end with Add-On disconnecting. HELP!

Similar Messages

Maybe you are looking for