Audigy 2 zs distorted and cracking so

hi..
I have audigy 2 zs platinum pro with gigaworks s750 speakers when I'm playing games and listen to MP3 music I get a lot of distorted and crack I just can get a clear sound try the newest driver but still all the same anyone can help.....

I think maybe you have your mic recording set on acti've. Go into windows control panel and double click the speaker icon/audio device settings. Click the audio tab on top, and then select volume in the "sound recording" section. Make sure that "Microphone" is not selected.

Similar Messages

Distortion and cracking noises together with hitches in video

Hello,
I have a question concerning the quality of the media on my laptop, concerning both graphical and audio gliching sounds and video crashes. They seem to occur at the exact same time so I'm guessing there is a connection beween the two of them. The specs on my laptop are:
Hewlett-Packard HP ENVY 17 Notebook - 2,40 gigahertz Intel Core i7-4700MQ - 64 bit
I use my NVIDIA GeForce GT 740M video card mostly but I have tried switching between the other standard video card Intel(R) HD Graphics 4600.
I have been using this Notebook for a few months now for school (I'm using a pretty heavy 3D design program, inventor), music, films and games. Until now it completely lived up to my expectations and I'm a quite content user but these noises and distortions are killing me. They occur with both my headphones and without (just the speakers on my laptop) about every 5 seconds. My notebook proudly wears the Beats Audio brand (honestly I don't believe that should guarantee anything concerning audio quality, it just so happend to be on the laptop that had drawn my attention.)
Now I have done a little research on the subject, after trying basic solutions like reinstalling my audio drivers and in generally looking up previous updates and checking the log, I had found a few threats that suggested it might have something to do with windows. but the Windows 8 help proved not to be sufficient to solve the problem.
Can you maybe help me out on this case?
Thanks in advance for the help!
This question was solved.
View Solution.

Hello JustSomeUser,
Welcome to the HP Forums!
Thank you for providing the troubleshooting steps that you have already done. Due to the video hitching and sound quality being poor at this time. I would suggest restoring back to the original graphics drivers. I have included the document 'Using Recovery Manager to Restore Software and Drivers (Windows 8)', After reinstalling the original drivers, please restart your notebook. Now you will have to reinstall the updated drivers. I have included the document 'Using HP Support Assistant (Windows 8)'. Please follow the steps for Updates and tune-ups.
Does this happen across all programs, or just particular programs? Are the programs that it does happen on Internet based? What file type of movies, and music are you playing? What player are you using to play movies, and music?
As well could you provide me with the full model number of your Envy 17. If you need it, I have included the document 'Guide to finding your product number'.
Thank you.
I worked on behalf of HP

Audigy 2 problems with spdif out not working and cracking appear

Hello everyone,
I am new in this forum but after searching through it i decided to post as i din't find a problem exactly similar to mine.
I have a Creative audigy 2 ZS plugged on my computer with this configuration : Gygabyte P35 DS3, Quad core Q6600, Kingston 2 gb.
From the beginning of my purchase i did not have any problem of cracking or connection problems in spdif with digital din in either XP or Vista. Last week end i decided to re install XP after a virus infection with XP SWEET wich install directly the drivers of my peripherals like the audigy.
The audigy is connected to my speakers : Creative? 5. kit 5700 via the digital din connection and without any analog connection as i selected digital out only in my settings.
Everything was working fine until 2 days ago when? while watching a divx the sound stopped working. i checked everything in m connection and everything was good as well as my speakers. finally i connected the audigy via analog cables to the speakers to find that, if i select digital out only no sound could be heard and finally that poping and cracking sounds started to appear.
I don't know what happened with my system as it never did that before in any of my configurations.
When i reboot my computer, the digital out start working again to finally stop 5 minutes later.
If somebody can help me is help would be most welcome.
Thank you!

Well, I do not know much about the red light thingy, but if the S-Bracket works well, it should be not problem, unless you can't get anything from the S-Bracket.

Audigy 2 ZS platinum sound distorted and muff

Too bad one cant rant as one might like in this forum. Had writtend all the details that transpired but when i pressed the submit post, my original post was lost due to expiration of time for my ticket.
Now, i use telegraph details.
Bought Audigy 2 ZS platinum, bad sound Distorted and muffled from the speakers except center speaker and no sound at all from rear center speaker. Same setup using Audigy Platinum, zero problems.
Using
Asus a7n8x-e Deluxe MB
024GB PC3200 Ram
ATI 9800 Pro AIW
Sound blaster Audigy 2 ZS Platinum
Creative DDTS-00 Decoder
Creative Inspire 6600 Speakers/Creative Inspire 5300 Speakers

Fabrizziov,
Is the sound muffled and distorted when you plug headphones into the headphone out on the platinum dri've? If not, plug the headphones into the sound card's front output and run a speaker test to see if it is muffled and distorted from there. If it is then it is most likely a problem with the card's hardware. If this is the case I would suggest exchanging it for another through your retailer. You can also contact support for a repair if needed. Their contact information is at http://us.creative.com/support/custsup.
Jeremy

Audigy 2zs Gamer and Windows Vista / Windows 7

.Audigy 2zs Gamer and Windows Vista / Windows 7? Hello, I am just wondering if it is a known issue to have really loud static and crackling when playing games using this card in Vista or Windows 7. I had this issue playing Bioshock a few months back on my Vista boot. I never figured out a way to resolve it so I belei've I just eventually uninstalled the driver and used the card without a driver install (not sure but I think this what I did). It worked but I might as well of just ran onboard sound...
Now I have installed and tried to run Windows 7 on a dual boot but I started receiving really loud cracking and popping in Warhammer Online and realized I had not installed a driver for my sound card. I did not expect creative to have a Win 7 driver yet but thought perhaps the Vista driver would work in compatibility mode, it does and sounds awesome and really makes me remember what I am missing without my driver installed on Vista but unfortunatly it randomly starts the crackling and popping again after a while...especially when a lot start happening on screen (pvp raids with many characters on screen and magic effects).
When the crackling starts happening I have no choice but to exit the game and restart the computer to get rid of the noise, but randomly it comes back after a while during gameplay. So as a temporary solution I have installed my onboard sound drivers and have been using that for sound output and my mic port on my sound card for my microphone. I would REALLY love to get my sound issues worked out in both Vista and Win 7 because it sounds SOOO awesome while it's working, the popping though is terrible, I never had that issue in XP.
I know this is an older card but any help would be appreciated!?
Message Edited by grimdeath9740 on 0-4-2009 2:3 PM@
68.95.29.2

One thing you do need to learn is that SHOUTING IS MUCH HARDER TO READ!
But, if you are using Audition 1 and it works with XP, then if you have the chance, I'd stick to that on a new machine. Apart from anything else, it's completely untried with Windows7 and with Vista its a) likely to have problems, and b) going to run slower.
The other part of your question about the 'look' of later versions is that 1.5 looks pretty similar to 1.0, but with 2.0 and 3.0 things have changed somewhat - rather more with Multitrack View than Edit View. Basic operating principle remains the same, though - most people have had very little trouble transferring from one to another.

Audigy 2 ZS and Surround Mixer in Windows 7

+?
Ok, I just installed Windows 7 Enterprise on a new HP XW 4600 workstation (NL, Dutch). This is a clean install. I have a Audigy 2 ZS (SB0350) and I dont have the surround mixer. Here is what I did:
?Install Windows 7 Enterprise and take all the pathes from Microsoft.
2.
?Intall the Audigy 2 ZS soundblaster? card in the computer
3.
?After the boot up I ingnore the message ?found new hardware?
4.
?I go to the Creative website and download the following programs
SBAX_PCDRV_LB_2_8_00 and WAVESTD_PCAPP_LB_7_2_00? which are recommended for my sound card.
5.
?I cant find the surround mixer, it is even not installed
6.
?I try the ?webupdate? there are some updates and I install them all
7.
?Again no Surround Mixer.
Can someone explain what I do or did wrong ?
I realy need the Surround Mixer !!

/Re: Audigy 2 ZS and Surround Mixer in Windows 7? i got problem with recording any sound. Recorded sounds are terrible. Sometimes playing sounds are terrible too. i should restart pc for fix playing terrible sound.
i found 2 third-party driver but i didnt tried. Because of decription of 3rd-party driver ;
There is no DirectSound hardware acceleration on Windows XP 64-bit (x64)
The Audigy driver does not support 64-bit addressing, disabling the DirectSound hardware acceleration and causing multichannel sound to be played only in the stereo channels (front left/right).
Workarounds:
- install the 32-bit (x86) version of Windows XP.
- limit to less than 4GB the amount of RAM available to Windows.
- enable the ?Memory Hole? setting in the BIOS Setup, if your motherboard supports it.
Microphone issues on Windows 7/Vista 64-bit (x64) with 4GB?of RAM or more
Audigy driver does not support 64-bit addressing, resulting in random issues with the Microphone (static, robotic or distorted voice, white noise).
Workarounds:
- install the 32-bit (x86) version of Windows
- limit the RAM available to Windows to less than 4GB
- enable Memore Hole in BIOS Setup, if?your motherboard supports the setting
Daniel K's Drivers
<a rel="nofollow" target="_blank" href="http://nomoregoatsoup.wordpress.com/2009/2//daniel_ks-sb-audigy-series-support-pack-3-6/"]http://nomoregoatsoup.wordpress.com/2009/2//daniel_ks-sb-audigy-series-support-pack-3-6/[/url]
[color="#000000"]
[color="#000000"]Robert McClelland's Drivers
<a rel="nofollow" target="_blank" href="http://www.hardwareheaven.com/pax-drivers/9629-fall-winter-pax-edtion-sets-more-set-added-later-one-thread.html"]http://www.hardwareheaven.com/pax-drivers/9629-fall-winter-pax-edtion-sets-more-set-added-later-one-thread.html[/url]

Audigy 2 ZS and Windows ME: switching to VXD drivers from WDM driv

Recently changed my sound card from an Audigy 2 to Audigy 2 ZS. OS is Windows ME. I used the VXD drivers with the old card and have been having lots of sound troubles that I have never experienced with a Creative card (distortion, sound sticking, etc.) using the WDM drivers and wanted to switch to the VXD drivers to see if this might correct problems. Have tried using CTZAPXX from original Audigy 2 ZS installation CD, but VXD drivers are grayed out.

I know it must be possible to switch to the VXD drivers, because on the Creative downloads page is a driver update with fixes "after switching to VXD drivers using Driver Utility."
One other note - When I do use the WDM drivers with this card, it is listed as "SBLi've!" under Audio Properties and it fails on Creative Diagnostics.


You have selected Audigy 2 ZS and Windows Millennium.To receive support for a different product, click here.
<IMG height= alt="" src="http://images.americas.creative.com//images/dot-clear.gif" width=8 border=0><IMG height= alt="" src="http://images.americas.creative.com//images/dot-clear.gif" width=378 border=0><IMG height= alt="" src="http://images.americas.creative.com//images/dot-clear.gif" width=73 border=0><IMG height= alt="" src="http://images.americas.creative.com//images/dot-clear.gif" width=7 border=0>
Drivers TitleDate <A target=_blank>[/url]<IMG height= alt="" src="http://images.americas.creative.com//images/dot-clear.gif" width=8 border=0><IMG height= alt="" src="http://images.americas.creative.com//images/dot-clear.gif" width=378 border=0><IMG height= alt="" src="http://images.americas.creative.com//images/dot-clear.gif" width=73 border=0><IMG height= alt="" src="http://images.americas.creative.com//images/dot-clear.gif" width=3 border=0><IMG height= alt="" src="http://images.americas.creative.com//images/dot-clear.gif" width=58 border=0>. EAX 4.0 ADVANCED HD Driver Update for Creative Sound Blaster Audigy 2/Audigy 2 ZS (3.57 MB) 9 Nov 03<IMG height=8 alt="Download Now" src="http://images.americas.creative.com//images/support/downloads/download-icon.gif" width=3 border=0>Download Now<IMG height=5 alt="" src="http://images.americas.creative.com//images/dot-clear.gif" width= border=0><IMG height= alt="" src="http://images.americas.creative.com//images/dot-clear.gif" width=8 border=0><IMG height= alt="" src="http://images.americas.creative.com//images/dot-clear.gif" width=522 border=0>
This driver update contains enhancements and fixes to improve the performance of your Creative Sound Blaster Audigy 2 or Creative Sound Blaster Audigy 2 ZS product.Hide Details
Filename: SBA2_EAX4DRV_0303.exe
This driver update contains enhancements and fixes to improve the performance of your Creative Sound Blaster Audigy 2 or Creative Sound Blaster Audigy 2 ZS product.
Added Feature:
EAX 4.0, containing DirectSound and Open AL API extensions, to utilize the EAX 4.0 ADVANCED HD Multiple Environment feature
</LI>
Fixes:
Removes noise from analog speakers after switching to VXD drivers using Driver Utility.</LI>
Allows compressed and uncompressed AC-3 signals when using VXD drivers.</LI>

Do you have an onboard audio processor? If so disable it in the BIOS and try to install the drivers from the CD first. Then head to Creative's web site and use the Auto Update option to dowload new drivers. If this does not work try installing the drivers from?a different driver if you have more than one. Some dri'ves that are defecti've or dying only install some disc contents before failing.?Hope this works for you!

Audigy 2 ZS and

I am getting a hum (grounding issues ?) when Audigy 2 ZS is in the PC.
The hum goes away (or is very faint)?when I disconnect my TV cable,?but theAudigy 2 ZS still has a tiny hum
PC line out is connected to my Panasonic receiver using a ground-loop-isolator cable, and TV cable to VCR, which is connected to receiver (A+V).
Any ideas how to rectify this ?
Where is problem ? Audigy 2 ZS or TV Cable ... or both ?

/Re: Audigy 2 ZS and Surround Mixer in Windows 7? i got problem with recording any sound. Recorded sounds are terrible. Sometimes playing sounds are terrible too. i should restart pc for fix playing terrible sound.
i found 2 third-party driver but i didnt tried. Because of decription of 3rd-party driver ;
There is no DirectSound hardware acceleration on Windows XP 64-bit (x64)
The Audigy driver does not support 64-bit addressing, disabling the DirectSound hardware acceleration and causing multichannel sound to be played only in the stereo channels (front left/right).
Workarounds:
- install the 32-bit (x86) version of Windows XP.
- limit to less than 4GB the amount of RAM available to Windows.
- enable the ?Memory Hole? setting in the BIOS Setup, if your motherboard supports it.
Microphone issues on Windows 7/Vista 64-bit (x64) with 4GB?of RAM or more
Audigy driver does not support 64-bit addressing, resulting in random issues with the Microphone (static, robotic or distorted voice, white noise).
Workarounds:
- install the 32-bit (x86) version of Windows
- limit the RAM available to Windows to less than 4GB
- enable Memore Hole in BIOS Setup, if?your motherboard supports the setting
Daniel K's Drivers
<a rel="nofollow" target="_blank" href="http://nomoregoatsoup.wordpress.com/2009/2//daniel_ks-sb-audigy-series-support-pack-3-6/"]http://nomoregoatsoup.wordpress.com/2009/2//daniel_ks-sb-audigy-series-support-pack-3-6/[/url]
[color="#000000"]
[color="#000000"]Robert McClelland's Drivers
<a rel="nofollow" target="_blank" href="http://www.hardwareheaven.com/pax-drivers/9629-fall-winter-pax-edtion-sets-more-set-added-later-one-thread.html"]http://www.hardwareheaven.com/pax-drivers/9629-fall-winter-pax-edtion-sets-more-set-added-later-one-thread.html[/url]

Xbox 360 X-Fi Distortion AND Lag problems through OPTICAL cable

I was wondering when there will be a fix or whatever because some of this is makeing me cringe in my chair... I?ordered optical to get better sounding games and Movies through the 5. support but the sound lags for about .2-.4 of a second causeing?sound to?not sync(echoes with RCA plugged in too, RCA being the one that plays sound FIRST!)?and the distortion is with LOUD sounds with something like an explosion causeing crackling and popping too. When will Creative fix this? i payed 300 dollars for this soundcard 6-7 months ago and they still have not fixed this issue which apparently has been there from the start of the xbox 360 launch. Also happens with the Xbox. Why even have something like an OPTICAL input if it doesn't work correctly. i would like to know a fix for this PLEASE!Message Edited by Assassinxkilla on 0-6-20070: PM
Message Edited by Assassinxkilla on 0-6-20070:3 PM

I definitely feel your pain. I have a Audigy 2 ZS and when connected with a PS3 or HDTV, the sound LAGS like half to one second. I've learned to deal with it at least for action games like Call of Duty 4 because even lagging surround gives an advantage over stereo. But it's annoying for TV or other stuff.
I've seen threads like this in alot of places. I just think Creative has some sloppy hardware that lags. It shouldn't be my computer because I've got a dual core with 2 GB RAM.
I shoulda just bought a Logitech Z-5500. That speaker system costs 200-250 but it has it's own digital decoder. You can plug in an optical or coax digital signal into the volume control and it will decode on its own without a sound card. Instead I bought a 20 dollar Logitech setup and a 00 dollar sound card (about three years ago).
If anyone ever finds a solution, I'd be glad to hear about it.Message Edited by phatfatpanda on 03-04-20082:22 PM

Jammed lock button and cracked screen!!! HELP PLEASE!!!

About three months after I bought my Ipod touch it fell off of my bed and cracked the screen entirely. I took it to Apple store and they said they couldn't replace it because it had no damage to the board and that it would cost $100 so I said screw it I can still read the screen. NOW I recently realized my lock/power button is jammed out of no where! I tried wiggling it with my nails, tapping it on the counter, and everything I could think of. I still have my warranty for another month or two. Can I get it replaced without charge? or what do I do? I really don't want to spend $100 bucks on this Ipod when every time I turn around something else happens. HELP please

Apple only exchanges the iPod for a refurbished one. Accidental damage like the broken screen voids the warranty on the entire iPod.

The glass on my new ipad air was broken one day. I have had it for about a month. 1 day I took it out of its case as usual and the screen was splintered at the top and cracked downwards. It had not received any bangs, or been dropped or anything. Help!

Hi, I have had my ipad air for about a month. The other day I took it out of its cover and it was splintered from the top with downward cracks. It is new and under warranty so I rang the support team. They told me that it would cost about €120 but could be repaired on the spot and they made me an appointment at the local genius bar. I got there and they told me that I had dropped it or banged it or something. I said I had not, they insisted that I must have done. I repeated several times that I had not - it was obvious they did not believe me, they said I must have done. They then told me they never repaired or replaced broken glass in any ipads, that the man on the 'Support' had been wrong. They always replaced the whole ipad at a cost of €300. I was devastated at not being believed and at the amount of money they were asking for. I left and rang the support again. I was told their system was down but to call on monday to get a quote for the reparation, I could send it to my home insurance company and they would undoubtedly cover the repair. I asked how long this was all going to take because, I was in the middle of a big project and this was taking up my time, and also I needed the ipad for my work. They told me it would be done in a minute. I rang on the Monday and I was told it would take up to 5 days to send but probably it would arrive sooner (it is now thursday, I have received nothing). I then rang my household insurance, a big company - and they told me they had never heard of such a cover. I asked if this was because I had a very basic policy, they said, no it wasn't that - I didn't have a basic policy I had quite thorough policy, but they didn't know of a policy in any comany that would cover this sort of damage. I was stunned - yet again I had been given false information and false hope by apple. Yet again I was let down. I then decided to do a further investigation on the internet and discovered a long trail of comments on Apple Forum of people who have also had splintering and cracking of the ipad air glass for no reason whatsoever. Some have commented that the glass could be thinner in order to reduce the weight, some have said that the splintering could be caused by a weakness in the casing at the top where it is plastic (the ones that take sims) that might make it more flexible and therefore liable to crack.
All of the posts and complaints on the apple forum and elsewhere seem to point to a design fault. However throughout all this I have been mislead by apple support staff constantly who all say different things, I have virtually been accused of lying by denying that my ipad received any kind of impact by apple staff and I have been left feeling incredibly frustrated and upset by the total lack of any kind of real help by Apple. All this despite being acomplet apple user in my business for the last 25 years, where I have never come across this attitude towards me as a customer before.
When the screen on my iphone broke, it was because I fell in the street while I was talking on the telephone, it flew out of my hand and smashed on the pavement. I was rolling around in agony, while my son was holding up the smashed telephone wailing 'Mama, you've smashed your iphone!!!' This of course, I blamed on noone but myself - it broke because it fell, I paid an arm and a leg without protest to get it repaired.
This is not the case with my new ipad air. It has splintered for no good reason at all - and noone at Apple seems to want to help me or to care!
I would really appreciate it if someone could tell me if there is anything else I can do to ge this matter resolved?

If it was a refurb replacing one that was under warranty, the warrany is good until the original warranty expires or 90 days from replacement, whichever is longer. In either event, it should still be covered if you've only had it for a month. (assuming you're in the US here). You can try to restore it as a NEW device rather than restoring from your backup, but this sounds like a hardware failure... I think. I'm not sure what you mean by "the top half of the screen slides". If you mean only the top half is touch sensitive, how can you determine that? You wouldn't be able to slide to unlock if that were the case...
Sorry, I'm a little confused by that description.

Since updating to 706 the sound on my ipad2 is not working right. On videos or music. There is constant distortion and what sounds like interference. Any ideas?

Since updating to 706 the sound on my ipad2 is not working right--on videos or music. There is distortion and some kind of interference at all times. Any ideas?

Has the unit EVER been jailbroke?
If "No," first try a system reset. It cures many ills and it's quick, easy and harmless...
Hold down the on/off switch and the Home button simultaneously until you see the Apple logo. Ignore the "Slide to power off" text if it appears. You will not lose any apps, data, music, movies, settings, etc.
If the Reset doesn't work, try a Restore. Note that it's nowhere near as quick as a Reset. It could take well over an hour! Connect via cable to the computer that you use for sync. From iTunes, select the iPad/iPod and then select the Summary tab. Follow the on-screen directions for Restore and be sure to say "yes" to the backup. You will be warned that all data (apps, music, movies, etc.) will be erased but, as the Restore finishes, you will be asked if you wish the contents of the backup to be copied to the iPad/iPod. Again, say "yes."
At the end of the basic Restore, you will be asked if you wish to sync the iPad/iPod. As before, say "yes." Note that that sync selection will disappear and the Restore will end if you do not respond within a reasonable time. If that happens, only the apps that are part of the IOS will appear on your device. Corrective action is simple - choose manual "Sync" from the bottom right of iTunes.
If you're unable to do the Restore, go into Recovery Mode per the instructions here. You WILL lose all of your data (game scores, etc,) but, for the most part, you can redownload apps and music without being charged again. Also, if you have IOS-7, read this.

Video on 2nd Monitor distorted and half sized

My superintendent has a X300 series laptop that he got when they first came out. We are running Windows XP Pro with SP3 on it. He has always connected a 2nd larger LCD screen on the vga output connector when in his office which has been working great until two months ago. Now the screen on the LCD monitor is somewhat distorted and is only half of the available screen width. We have changed resolutions, monitors, and video cables but nothing has worked. We do have the latest Microsoft patches and we use Sophos for virus protection.
Does anyone have any ideas?
Thanks
Bill

Bill, welcome to the forum,
it may be possible that a video driver has been installed automatically with Windows updates, I've seen occasions when this has happened and caused chaos. Try rolling back the driver to the original which should be found in c:\swtools\drivers\video, or download and install the current driver from here. Please ensure you follow the installation instructions on the site.
Hope this helps
Andy ______________________________________
Please remember to come back and mark the post that you feel solved your question as the solution, it earns the member + points
Did you find a post helpfull? You can thank the member by clicking on the star to the left awarding them Kudos Please add your type, model number and OS to your signature, it helps to help you. Forum Search Option T430 2347-G7U W8 x64, Yoga 10 HD+, Tablet 1838-2BG, T61p 6460-67G W7 x64, T43p 2668-G2G XP, T23 2647-9LG XP, plus a few more. FYI Unsolicited Personal Messages will be ignored.
Deutsche Community Comunidad en Español English Community Русскоязычное Сообщество
PepperonI blog

Exported Video is fine on Windows media player for test upload on Youtube now distorted and unfluent

I made a "slideshow" for a product video for work those are my sequence settings
I exported it at H264 and 1080p 29.97
When I played it in Windows media player it ran perfectly now all of a sudden when I uploaded it to Youtube it is completely distorted and unfluent (all the animations, face in and out) look horrible.
Does somebody know why this changes so drastically from media player to youtube or did I do the wrong settings when exporting it?
It would be life saving if someone could help me thanks! :-)

I tried that but that doesn't get rid of the problem.
You are right there are no video files...
Do you know which settings I have to chose in general if I want to have a video that can be exported onto youtube in HD?
Because I am out of options does it have to do with the fps maybe? Because it looks so chopped of as if the video is to slow to process it smoothly?
Thanks so much for your help btw :-)

Music is Distorted and Skips

I currently have the iphone 5 and my software has been udpated to 6.1.4. But the issue I am having is that, when I'm running or working out, my music would sound distorted and skips. This is the only time it happens. Any suggestions or ways to resolve this? Thank you so much!

Hi, I have the same issue, on MP3 and AAC almost can't notice, but using HE-AAC its very noisy.
My wife use the Ipod Nano (with touch) and the same song (excatly same source, because I shared the folder between different users on the computer) and the music plays perfectly.
ps.: I have tested using the same song, from same source and same compression and also the same earphones (that came with my ipod classic)
Its software a bug or hardware?

Audigy 2 zs distorted and cracking so

Similar Messages

Maybe you are looking for