Auto Deploy and VCD Network Isolation - Not Working

Hello,
I have opened a support case about this issue, but the case is moving a lot slower than I would like to see. I thought I'd post here to see if anyone has ran into anything similar.
We recently switched our 24-host vCloud cluster (more info about this cluster below) over to Auto-Deploy (was using boot from USB). After the switch, we had a few complaints from customers that use isolated networks. It turns out that only 4 of our 24 hosts were working properly with isolated networks. All 24-hosts are using the same auto-deploy image.
When the hosts boot up, the vCloud Director web interface shows the following with green check marks: "Status", "Enabled", "Ready", "Available", and "VCD Network Isolation Capable".
To get my other 20 hosts working, I disabled all 20 hosts in the vCloud interface, unprepared them, and prepared them. After this, network isolation worked for those 20 hosts. When I reboot one of the hosts, the host still looks like it's good in the interface, but network isolation doesn't work until I disable, unprepare, and prepare.
Here is some more information about our environment:
vCenter build 2001466
ESXi Host Build 2702864
VCD Build 5.5.2.2000523
vShield Build 5.5.3
Here is the Deploy Rule that the hosts are using:
Name        : UCS-2.2.1-pcloud.5.5.aln
PatternList : {oemstring=$SPT:ESX_PublicCloud_autod.2.2.x}
ItemList    : {ESXi-5.5.0-autod-2.2.1.vshield}
I have confirmed that this is indeed the profile being used by looking at the Summary tab for the hosts and seeing the listed Image Profile.
And here is what's in that item:
PowerCLI D:\ImageBuild> Get-EsxSoftwarePackage
Name                     Version                        Vendor     Creation Date
misc-cnic-register       1.72.1.v50.1i-1vmw.550.0.0.... VMware     9/19/2013 6:0...
scsi-lpfc820             8.2.3.1-129vmw.550.0.0.1331820 VMware     9/19/2013 6:0...
scsi-megaraid-mbox       2.20.5.1-6vmw.550.0.0.1331820 VMware     9/19/2013 6:0...
esx-xlibs                5.5.0-0.0.1331820              VMware     9/19/2013 6:0...
lpfc                     10.0.100.1-1vmw.550.0.0.133... VMware     9/19/2013 6:0...
mtip32xx-native          3.3.4-1vmw.550.1.15.1623387    VMware     2/22/2014 1:1...
net-nx-nic               5.0.621-1vmw.550.0.0.1331820   VMware     9/19/2013 6:0...
block-cciss              3.6.14-10vmw.550.0.0.1331820   VMware     9/19/2013 6:0...
scsi-fnic                1.6.0.5-1OEM.500.0.0.472560    cisco      9/30/2013 11:...
net-enic                 2.1.2.42-1OEM.500.0.0.472560   Cisco      9/5/2013 8:30...
sata-sata-sil24          1.1-1vmw.550.0.0.1331820       VMware     9/19/2013 6:0...
rste                     2.0.2.0088-4vmw.550.1.15.16... VMware     2/22/2014 1:1...
elxnet                   10.0.100.0v-1vmw.550.0.0.13... VMware     9/19/2013 6:0...
scsi-aacraid             1.1.5.1-9vmw.550.0.0.1331820   VMware     9/19/2013 6:0...
ata-pata-cmd64x          0.2.5-3vmw.550.0.0.1331820     VMware     9/19/2013 6:0...
net-cnic                 1.72.52.v55.1-1vmw.550.0.0.... VMware     9/19/2013 6:0...
scsi-adp94xx             1.0.8.12-6vmw.550.0.0.1331820 VMware     9/19/2013 6:0...
net-be2net               4.6.100.0v-1vmw.550.0.0.133... VMware     9/19/2013 6:0...
net-ixgbe                3.7.13.7.14iov-12vmw.550.2.... VMware     4/29/2015 6:4...
net-igb                  5.0.5.1.1-1vmw.550.2.54.240... VMware     1/1/2015 8:00...
epsec-mux                5.1.0-01814505                 VMware     5/13/2014 4:3...
esx-base                 5.5.0-2.62.2702864             VMware     4/29/2015 6:4...
ata-pata-sil680          0.4.8-3vmw.550.0.0.1331820     VMware     9/19/2013 6:0...
ipmi-ipmi-msghandler     39.1-4vmw.550.0.0.1331820      VMware     9/19/2013 6:0...
ata-pata-hpt3x2n         0.3.4-3vmw.550.0.0.1331820     VMware     9/19/2013 6:0...
scsi-megaraid-sas        5.34-9vmw.550.2.33.2068190     VMware     8/23/2014 1:5...
scsi-mptsas              4.23.01.00-9vmw.550.0.0.133... VMware     9/19/2013 6:0...
net-bnx2                 2.2.3d.v55.2-1vmw.550.0.0.1... VMware     9/19/2013 6:0...
ata-pata-via             0.3.3-2vmw.550.0.0.1331820     VMware     9/19/2013 6:0...
ima-qla4xxx              2.01.31-1vmw.550.0.0.1331820   VMware     9/19/2013 6:0...
ata-pata-amd             0.3.10-3vmw.550.0.0.1331820    VMware     9/19/2013 6:0...
ata-pata-serverworks     0.4.3-3vmw.550.0.0.1331820     VMware     9/19/2013 6:0...
sata-sata-promise        2.12-3vmw.550.0.0.1331820      VMware     9/19/2013 6:0...
sata-sata-nv             3.5-4vmw.550.0.0.1331820       VMware     9/19/2013 6:0...
ipmi-ipmi-devintf        39.1-4vmw.550.0.0.1331820      VMware     9/19/2013 6:0...
scsi-ips                 7.12.05-4vmw.550.0.0.1331820   VMware     9/19/2013 6:0...
sata-sata-svw            2.3-3vmw.550.0.0.1331820       VMware     9/19/2013 6:0...
scsi-mptspi              4.23.01.00-9vmw.550.0.0.133... VMware     9/19/2013 6:0...
net-e1000e               1.1.2-4vmw.550.1.15.1623387    VMware     2/22/2014 1:1...
esx-xserver              5.5.0-0.0.1331820              VMware     9/19/2013 6:0...
net-tg3                  3.123c.v55.5-1vmw.550.2.33.... VMware     8/23/2014 1:5...
net-forcedeth            0.61-2vmw.550.0.0.1331820      VMware     9/19/2013 6:0...
scsi-aic79xx             3.1-5vmw.550.0.0.1331820       VMware     9/19/2013 6:0...
sata-ata-piix            2.12-10vmw.550.2.33.2068190    VMware     8/23/2014 1:5...
scsi-bnx2i               2.72.11.v55.4-1vmw.550.0.0.... VMware     9/19/2013 6:0...
ohci-usb-ohci            1.0-3vmw.550.0.0.1331820       VMware     9/19/2013 6:0...
scsi-qla4xxx             5.01.03.2-6vmw.550.0.0.1331820 VMware     9/19/2013 6:0...
scsi-qla2xxx             902.k1.1-9vmw.550.0.0.1331820 VMware     9/19/2013 6:0...
net-mlx4-core            1.9.7.0-1vmw.550.0.0.1331820   VMware     9/19/2013 6:0...
ata-pata-atiixp          0.4.6-4vmw.550.0.0.1331820     VMware     9/19/2013 6:0...
misc-drivers             5.5.0-2.62.2702864             VMware     4/29/2015 6:4...
esx-dvfilter-generic-... 5.5.0-0.0.1331820              VMware     9/19/2013 6:0...
ata-pata-pdc2027x        1.0-3vmw.550.0.0.1331820       VMware     9/19/2013 6:0...
qlnativefc               1.0.12.0-1vmw.550.0.0.1331820 VMware     9/19/2013 6:0...
lsi-mr3                  0.255.03.01-2vmw.550.1.16.1... VMware     4/15/2014 9:0...
vshield                  5.5.3-2172759                  VMware     9/30/2014 2:3...
net-vmxnet3              1.1.3.0-3vmw.550.2.39.2143827 VMware     9/18/2014 11:...
scsi-hpsa                5.5.0-44vmw.550.0.0.1331820    VMware     9/19/2013 6:0...
tools-light              5.5.0-2.62.2702864             VMware     4/29/2015 6:4...
scsi-mpt2sas             14.00.00.00-3vmw.550.1.15.1... VMware     2/22/2014 1:1...
scsi-bnx2fc              1.72.53.v55.1-1vmw.550.0.0.... VMware     9/19/2013 6:0...
lsi-msgpt3               00.255.03.03-1vmw.550.1.15.... VMware     2/22/2014 1:1...
net-e1000                8.0.3.1-3vmw.550.0.0.1331820   VMware     9/19/2013 6:0...
xhci-xhci                1.0-2vmw.550.2.39.2143827      VMware     9/18/2014 11:...
ipmi-ipmi-si-drv         39.1-4vmw.550.0.0.1331820      VMware     9/19/2013 6:0...
sata-ahci                3.0-21vmw.550.2.54.2403361     VMware     1/1/2015 8:00...
net-bnx2x                1.72.56.v55.2-1vmw.550.0.0.... VMware     9/19/2013 6:0...
scsi-megaraid2           2.00.4-9vmw.550.0.0.1331820    VMware     9/19/2013 6:0...
ehci-ehci-hcd            1.0-3vmw.550.0.0.1331820       VMware     9/19/2013 6:0...
esx-tboot                5.5.0-2.33.2068190             VMware     8/23/2014 1:5...
uhci-usb-uhci            1.0-3vmw.550.0.0.1331820       VMware     9/19/2013 6:0...
sata-sata-sil            2.3-4vmw.550.0.0.1331820       VMware     9/19/2013 6:0...
vcloud-agent             5.5.0-1280396                  VMware     8/17/2013 4:0...
net-mlx4-en              1.9.7.0-1vmw.550.0.0.1331820   VMware     9/19/2013 6:0...
And here is the output of testing the deploy rule compliance:
PowerCLI D:\ImageBuild> Get-Cluster 0000000-ESXVCLOUDCL1.ALN | Get-VMHost |Test-
DeployRuleSetCompliance
VMHost               ItemList
esx142269.vm.seo.... {}
esx140622.vm.seo.... {}
esx139784.vm.seo.... {}
esx140617.vm.seo.... {}
esx138793.vm.seo.... {}
esx135523.vm.seo.... {}
esx138945.vm.seo.... {}
esx138794.vm.seo.... {}
esx139783.vm.seo.... {}
esx140309.vm.seo.... {}
esx140310.vm.seo.... {}
esx140311.vm.seo.... {}
esx140313.vm.seo.... {}
esx140339.vm.seo.... {}
esx140614.vm.seo.... {}
esx140615.vm.seo.... {}
esx140616.vm.seo.... {}
esx140618.vm.seo.... {}
esx140619.vm.seo.... {}
esx140621.vm.seo.... {}
esx141947.vm.seo.... {}
esx141945.vm.seo.... {}
esx142271.vm.seo.... {}
esx142270.vm.seo.... {}
Here is another vib list from a host:
~ # esxcli software vib list
Name                           Version                                Vendor Acceptance Level Install Date
net-enic                       2.1.2.42-1OEM.500.0.0.472560           Cisco   VMwareCertified   -
ata-pata-amd                   0.3.10-3vmw.550.0.0.1331820            VMware VMwareCertified   -
ata-pata-atiixp                0.4.6-4vmw.550.0.0.1331820             VMware VMwareCertified   -
ata-pata-cmd64x                0.2.5-3vmw.550.0.0.1331820             VMware VMwareCertified   -
ata-pata-hpt3x2n               0.3.4-3vmw.550.0.0.1331820             VMware VMwareCertified   -
ata-pata-pdc2027x              1.0-3vmw.550.0.0.1331820               VMware VMwareCertified   -
ata-pata-serverworks           0.4.3-3vmw.550.0.0.1331820             VMware VMwareCertified   -
ata-pata-sil680                0.4.8-3vmw.550.0.0.1331820             VMware VMwareCertified   -
ata-pata-via                   0.3.3-2vmw.550.0.0.1331820             VMware VMwareCertified   -
block-cciss                    3.6.14-10vmw.550.0.0.1331820           VMware VMwareCertified   -
ehci-ehci-hcd                  1.0-3vmw.550.0.0.1331820               VMware VMwareCertified   -
elxnet                         10.0.100.0v-1vmw.550.0.0.1331820       VMware VMwareCertified   -
epsec-mux                      5.1.0-01814505                         VMware VMwareCertified   -
esx-base                       5.5.0-2.62.2702864                     VMware VMwareCertified   -
esx-dvfilter-generic-fastpath 5.5.0-0.0.1331820                      VMware VMwareCertified   -
esx-tboot                      5.5.0-2.33.2068190                     VMware VMwareCertified   -
esx-xlibs                      5.5.0-0.0.1331820                      VMware VMwareCertified   -
esx-xserver                    5.5.0-0.0.1331820                      VMware VMwareCertified   -
ima-qla4xxx                    2.01.31-1vmw.550.0.0.1331820           VMware VMwareCertified   -
ipmi-ipmi-devintf              39.1-4vmw.550.0.0.1331820              VMware VMwareCertified   -
ipmi-ipmi-msghandler           39.1-4vmw.550.0.0.1331820              VMware VMwareCertified   -
ipmi-ipmi-si-drv               39.1-4vmw.550.0.0.1331820              VMware VMwareCertified   -
lpfc                           10.0.100.1-1vmw.550.0.0.1331820        VMware VMwareCertified   -
lsi-mr3                        0.255.03.01-2vmw.550.1.16.1746018      VMware VMwareCertified   -
lsi-msgpt3                     00.255.03.03-1vmw.550.1.15.1623387     VMware VMwareCertified   -
misc-cnic-register             1.72.1.v50.1i-1vmw.550.0.0.1331820     VMware VMwareCertified   -
misc-drivers                   5.5.0-2.62.2702864                     VMware VMwareCertified   -
mtip32xx-native                3.3.4-1vmw.550.1.15.1623387            VMware VMwareCertified   -
net-be2net                     4.6.100.0v-1vmw.550.0.0.1331820        VMware VMwareCertified   -
net-bnx2                       2.2.3d.v55.2-1vmw.550.0.0.1331820      VMware VMwareCertified   -
net-bnx2x                      1.72.56.v55.2-1vmw.550.0.0.1331820     VMware VMwareCertified   -
net-cnic                       1.72.52.v55.1-1vmw.550.0.0.1331820     VMware VMwareCertified   -
net-e1000                      8.0.3.1-3vmw.550.0.0.1331820           VMware VMwareCertified   -
net-e1000e                     1.1.2-4vmw.550.1.15.1623387            VMware VMwareCertified   -
net-forcedeth                  0.61-2vmw.550.0.0.1331820              VMware VMwareCertified   -
net-igb                        5.0.5.1.1-1vmw.550.2.54.2403361        VMware VMwareCertified   -
net-ixgbe                      3.7.13.7.14iov-12vmw.550.2.62.2702864 VMware VMwareCertified   -
net-mlx4-core                  1.9.7.0-1vmw.550.0.0.1331820           VMware VMwareCertified   -
net-mlx4-en                    1.9.7.0-1vmw.550.0.0.1331820           VMware VMwareCertified   -
net-nx-nic                     5.0.621-1vmw.550.0.0.1331820           VMware VMwareCertified   -
net-tg3                        3.123c.v55.5-1vmw.550.2.33.2068190     VMware VMwareCertified   -
net-vmxnet3                    1.1.3.0-3vmw.550.2.39.2143827          VMware VMwareCertified   -
ohci-usb-ohci                  1.0-3vmw.550.0.0.1331820               VMware VMwareCertified   -
qlnativefc                     1.0.12.0-1vmw.550.0.0.1331820          VMware VMwareCertified   -
rste                           2.0.2.0088-4vmw.550.1.15.1623387       VMware VMwareCertified   -
sata-ahci                      3.0-21vmw.550.2.54.2403361             VMware VMwareCertified   -
sata-ata-piix                  2.12-10vmw.550.2.33.2068190            VMware VMwareCertified   -
sata-sata-nv                   3.5-4vmw.550.0.0.1331820               VMware VMwareCertified   -
sata-sata-promise              2.12-3vmw.550.0.0.1331820              VMware VMwareCertified   -
sata-sata-sil24                1.1-1vmw.550.0.0.1331820               VMware VMwareCertified   -
sata-sata-sil                  2.3-4vmw.550.0.0.1331820               VMware VMwareCertified   -
sata-sata-svw                  2.3-3vmw.550.0.0.1331820               VMware VMwareCertified   -
scsi-aacraid                   1.1.5.1-9vmw.550.0.0.1331820           VMware VMwareCertified   -
scsi-adp94xx                   1.0.8.12-6vmw.550.0.0.1331820          VMware VMwareCertified   -
scsi-aic79xx                   3.1-5vmw.550.0.0.1331820               VMware VMwareCertified   -
scsi-bnx2fc                    1.72.53.v55.1-1vmw.550.0.0.1331820     VMware VMwareCertified   -
scsi-bnx2i                     2.72.11.v55.4-1vmw.550.0.0.1331820     VMware VMwareCertified   -
scsi-hpsa                      5.5.0-44vmw.550.0.0.1331820            VMware VMwareCertified   -
scsi-ips                       7.12.05-4vmw.550.0.0.1331820           VMware VMwareCertified   -
scsi-lpfc820                   8.2.3.1-129vmw.550.0.0.1331820         VMware VMwareCertified   -
scsi-megaraid-mbox             2.20.5.1-6vmw.550.0.0.1331820          VMware VMwareCertified   -
scsi-megaraid-sas              5.34-9vmw.550.2.33.2068190             VMware VMwareCertified   -
scsi-megaraid2                 2.00.4-9vmw.550.0.0.1331820            VMware VMwareCertified   -
scsi-mpt2sas                   14.00.00.00-3vmw.550.1.15.1623387      VMware VMwareCertified   -
scsi-mptsas                    4.23.01.00-9vmw.550.0.0.1331820        VMware VMwareCertified   -
scsi-mptspi                    4.23.01.00-9vmw.550.0.0.1331820        VMware VMwareCertified   -
scsi-qla2xxx                   902.k1.1-9vmw.550.0.0.1331820          VMware VMwareCertified   -
scsi-qla4xxx                   5.01.03.2-6vmw.550.0.0.1331820         VMware VMwareCertified   -
uhci-usb-uhci                  1.0-3vmw.550.0.0.1331820               VMware VMwareCertified   -
vcloud-agent                   5.5.0-1280396                          VMware VMwareCertified   -
vmware-fdm                     5.5.0-2001466                          VMware VMwareCertified   -
vshield                        5.5.3-2172759                          VMware VMwareCertified   -
xhci-xhci                      1.0-2vmw.550.2.39.2143827              VMware VMwareCertified   -
tools-light                    5.5.0-2.62.2702864                     VMware VMwareCertified   -
scsi-fnic                      1.6.0.5-1OEM.500.0.0.472560            cisco   VMwareCertified   -
Any help is appreciated. Thanks.

Right now, on my test host (that is not working), I have two VMs, one named "Test 1" and the other "Test 2" They only have an isolated network on them (named "Test Isolated Network") that is in my VDC, and pings do not work between them. If I move them to any other host (that have been unprepared and prepared), pings work. I can move both to the same host, or different hosts.
Here is the fence info on this host, I'm not really sure how to interpret this:
~ # esxcli vcloud fence getfenceinfo
   Module Parameters:
        Host Key: 0x104b0
        Configured LAN MTUs:
        +------------------------------------------------------------------------------------------+
        | LAN ID |    1    2    3    4    5    6    7    8    9   10    -    -    -    -    -    - |
        |    MTU | 1500 1500 1500 1500 1500 1500 1500 1500 1500 1500    -    -    -    -    -    - |
        +------------------------------------------------------------------------------------------+
   Active Ports:
        +-----------------------------------------+
        |     ID       |    OPI    | LanID | MTU |
        +-----------------------------------------+
        | 410b1d4ce7d0 | 01,0001a2 |     4 | 1500 |
        | 410b1d4cfde0 | 01,0001a2 |     4 | 1500 |
        +-----------------------------------------+
   Switch State:
        +-----------------------------------------------------+
        |   Inner MAC    |   Outer MAC   | used | age | seen |
        +-----------------------------------------------------+
        + ............................... Port:0x410b1d4ce7d0 +
        +-----------------------------------------------------+
        + ............................... Port:0x410b1d4cfde0 +
        | 00:50:56:01:06:16 | 00:13:F5:01:04:B4 | 1 | 1 | 1 |
        +-----------------------------------------------------+
   Port Statistics Summary:
        +-----------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------+
        |       Identity           |               To VM dropped                         | To VM passed    |     From VM dropped                        |                 From VM passed                      | Reflect        |
        |   Port ID    | Fence ID | total | misunf | misfen | stored | frag   | other | fenced | join   | unfen | csum   | frag   | GVT    | other | fenced | tso    | frag   | csum   | GVT    | ufport | pass   | error |
        +-----------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------+
        | 410b1d4ce7d0 | 01,0001a2 |   3991 |      2 |   3976 |      0 |      0 |      0 |     13 |      0 |      0 |      0 |      0 |      0 |      0 |    679 |      0 |      0 |      0 |      0 |      0 |      0 |      0 |
        +-----------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------+
        | 410b1d4cfde0 | 01,0001a2 |   4478 |      2 |   3860 |      0 |      0 |      0 |    616 |      0 |      0 |      0 |      0 |      0 |      0 |    626 |      0 |      0 |      0 |      0 |      0 |      0 |      0 |
        +-----------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------+
And here is the output of the command a little while later on the same host (while my test pings are going)
~ # esxcli vcloud fence getfenceinfo
   Module Parameters:
        Host Key: 0x104b0
        Configured LAN MTUs:
        +------------------------------------------------------------------------------------------+
        | LAN ID |    1    2    3    4    5    6    7    8    9   10    -    -    -    -    -    - |
        |    MTU | 1500 1500 1500 1500 1500 1500 1500 1500 1500 1500    -    -    -    -    -    - |
        +------------------------------------------------------------------------------------------+
   Active Ports:
        +-----------------------------------------+
        |     ID       |    OPI    | LanID | MTU |
        +-----------------------------------------+
        | 410b1d4ce7d0 | 01,0001a2 |     4 | 1500 |
        | 410b1d4cfde0 | 01,0001a2 |     4 | 1500 |
        +-----------------------------------------+
   Switch State:
        +-----------------------------------------------------+
        |   Inner MAC    |   Outer MAC   | used | age | seen |
        +-----------------------------------------------------+
        + ............................... Port:0x410b1d4ce7d0 +
        +-----------------------------------------------------+
        + ............................... Port:0x410b1d4cfde0 +
        | 00:50:56:01:06:16 | 00:13:F5:01:04:B4 | 1 | 1 | 1 |
        +-----------------------------------------------------+
   Port Statistics Summary:
        +-----------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------+
        |       Identity           |               To VM dropped                         | To VM passed    |     From VM dropped                        |                 From VM passed                      | Reflect        |
        |   Port ID    | Fence ID | total | misunf | misfen | stored | frag   | other | fenced | join   | unfen | csum   | frag   | GVT    | other | fenced | tso    | frag   | csum   | GVT    | ufport | pass   | error |
        +-----------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------+
        | 410b1d4ce7d0 | 01,0001a2 |   4696 |      2 |   4681 |      0 |      0 |      0 |     13 |      0 |      0 |      0 |      0 |      0 |      0 |    796 |      0 |      0 |      0 |      0 |      0 |      0 |      0 |
        +-----------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------+
        | 410b1d4cfde0 | 01,0001a2 |   5300 |      2 |   4565 |      0 |      0 |      0 |    733 |      0 |      0 |      0 |      0 |      0 |      0 |    743 |      0 |      0 |      0 |      0 |      0 |      0 |      0 |
        +-----------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------+
Looking at the VDS, the Maximum MTU is set to 1500. Looking at dvs.VCDVSTest Isolated Network-ca9a45c9-1dec-4f95-8b96-68d9c05b2a5d, I see it's VLAN is set to 2535 (which matches the network pool settings) and number of ports is 16

Similar Messages

After upgrading to windows 10 Auto-rotate and touchpad gestures does not work

I have installed the latest HP Support Assistant for windows 10 and I have installed the updates Intel Virtual Button DriverHP System Event Utility Updates failed to install without giving reason: Intel Serial I/O driver Intel Management Engine Interface (MEI) Driver In display settings I have checked the box of "Allow the screen to auto-rotate" But all these have not worked. Please find a solution for me.

Yes. I found the answer here:http://h30434.www3.hp.com/t5/Notebook-Display-and-Video/HP-Envy-x2-13-j020CA-Windows-10-Auto-Rotate-Autorotate-now/m-p/5212887#M115445I've tried replacing the driver on Sdo Sensor V2 device with the Simple Device Orientation Sensor and rotation works just like it did on 8.1.For the record - Sdo Sensor v2 reports the device orientation continiously, and Simple Device Orientation Sensor reports it only when the orientation changes. Must be a Windows bug then.

Wireless and Ethernet Network Do Not Work Other Than SpeedTest

I have been having major problems with my Mac's Internet. Whenever I connect to my Wireless or Ethernet Connection, the signal start out strong and dies down to almost nothing (around .4 kbps) immediatly. I have been having this problem for a couple of weeks now. However, when I run SpeedTest.net, I get the connection speeds which I should be getting. My Network Application thingy (iStat Menus) shows a major increase from .4kbps to 6MBps when the speedtest in running. Any ideas on how I can fix this problem?

It's a router all right. The next question is what is the "downstairs" device? Router or...?
The Aliant is configured through a browser interface and its IP address ought to be 192.168.2.1. Put those numbers in Safari's URL field and see if its webpage loads. If it does, you might be able to find a setting called "bridge mode".
Beware that I'm way out in the weeds with this suggestion - changing things in that unit may cause you even more problems. Since you said it is connected to a "wall Ethernet plug" I'm concluding that it should not be acting as a router, but that depends on what is upstream of that wall plug, and what functions the downstairs device is performing.
If the "wall Ethernet plug" is in fact a phone line and not an Ethernet LAN port then it is your router and you won't want to change that.

My auto-indent and code formatting is not working.

Usually on dreamweaver CS5.5 my code (html) would indent my <div> tags and align them up with the end div </div>. Not only were the <siv> tags formateed but various of others tags were as well.
How Dreamweaver used to format my code:
<head>
          <title>Example</title>
          <link rel="stylesheet" href="style.css" type="text/css" media="screen" />
</head>
<body>
<div id="outside_container">
          <div id="container">
                    <a href="#"><img src="images/logo.jpg" id="logo" /></a>
        <ul id="menu">
                  <li><a href="#"></a></li>
                  <li><a href="#"></a></li>
                  <li><a href="#"></a></li>
                    </ul>
        <ul id="right_menu">
                  <li><a href="#">t</a></li>
                  <li><a href="#">t</a></li>
        </ul>
        <img src="images/panel_home.jpg" id="panel" />
                    <div id="content">
                  <div class="column1">
                      <h2>Text</h2>
                <p>Text Here</p>
            </div>
Now it does not even format it so all of my code aligns on the left like so:
<head>
<title>Example</title>
<link rel="stylesheet" href="style.css" type="text/css" media="screen" />
</head>
<body>
<div id="outside_container">
<div id="container">
<a href="#"><img src="images/logo.jpg" id="logo" /></a>
<ul id="menu">
<li><a href="#"></a></li>
<li><a href="#"></a></li>
<li><a href="#"></a></li>
</ul>
<ul id="right_menu">
<li><a href="#">t</a></li>
<li><a href="#">t</a></li>
</ul>
<img src="images/panel_home.jpg" id="panel" />
Can anybody please help me?

Did you try Edit > Preferences > Code Format > Indent?
Nancy O.
Alt-Web Design & Publishing
Web | Graphics | Print | Media Specialists
http://alt-web.com/
http://twitter.com/altweb

My network is not working i am in ghana and i use MTN network but it is not working why is it like that

my network is not working i am in ghana and i use MTN network but it is not working why is it like that... pls get back to me now

It sounds as if you need to call your mobile carrier.

My iphone 4 is runing on ios 7.1.2 and the network appers not to be working....any help

my iphone 4 is runing on ios 7.1.2 and the network appers not to be working....any help

Did you already try the tips mentioned in this article?
iOS: Wi-Fi settings grayed out or dim

I have iphone 4 and i used it for a one and half years.i used it in sri lanka and doha qatar,recently i update it i.o.s 7, then it was working.after i.o.s 7.0.3 came i again updeted it and now my phone network is not working.now phone is locked.pls help.

i have iphone 4 and i used it for a one and half years.i used it in sri lanka and doha qatar also..,recently i update it i.o.s 7, then it was working.after i.o.s 7.0.3 came i again updeted it and now my phone network is not working.now phone is locked.pls help.

I am seeing if I can get another battery even though I do not believe that is the issue. It keeps giving me vdd_under which I believe is under voltage, maybe it is just a faulty battery? It charges up like normal and functions normal (when plugged in, or above 90%) but it gives under voltage warnings and shuts down when in heavy use (using camera or going back and forth to imessage). When just sitting idle it doesn't seem to turn off until that 55-60% mark. It may just be a faulty battery because I feel I installed all of the other cables correctly when replacing the screen, and I don't think those connections should affect the battery anyway except for maybe the logic board cable (the 2nd cable to be unplugged after the battery cable) I guess I could clean that out as well with isopropyl just in case.
Any other suggestions would be helpful... and I will get back to you if a new battery helps. Thanks!

So my airport extreme recently had some nat/dns issue and in the airport utility displayed a warning about it and to correct it. I wasn't sure what to do so i pressed the resolve icon and now my guest network is not working.

So my airport extreme recently had some nat/dns issue and in the airport utility displayed a warning about it and to correct it. I wasn't sure what to do so i pressed the resolve icon and now my guest network is not working.

Anytime you change networking hardware, it is always a good idea to perform a complete power recycle of your networking components.
I would recommend that you do the following as a minimum:
Power-down the modem, AirPort base station, and computer(s).
Disconnect the AirPort base station from the Internet broadband modem.
While all of the devices are powered-down, perform a "factory default" reset on the base station. This will get it back to its "out-of-the-box" configuration and make setting it up much easier, especially if you use the "Assist me" process within the AirPort Utility. (ref: Resetting an AirPort Base Station or Time Capsule)
After the base station resets, go ahead and power it back down.
Reconnect the AirPort base station to the Internet broadband modem. For the Extreme and Time Capsule, be sure to connect the cable to the base station's WAN (circle-of-dots) port.
Power-up the modem; wait at least 10-15 minutes to allow it adequate time to initialize.
Power-up the AirPort base station; wait at least 5-10 minutes. Note: The AirPort's status light may continue to flash amber after it has intialized. That is because, there may be some additional configuration items necessary, like setting up wireless security, before the overall setup is completed to get a green status.
Power-up your computer(s).
In this basic configuration, the AirPort base station will broadcast an unsecured wireless network with a Network Name (SSID) of Apple Network NNNNNN. Network clients, connected to the base station either by wire or wireless, should now be able to access the Internet through the ISP's modem. Once Internet connectivity has been verified, you can use the AirPort Utility to configure the base station for wireless security and any other desired options. Please post back your results.

My home sharing and remote app does not work. How do I fix it? I am on a university network.

My home sharing and remote app does not work.
Here is my setup:
Macbook 2009 running Mac OS X 10.6.8
Itunes 10.6.1
Ipod Touch 4th gen Mac OS X 5.1
I am on a university secured network.

Hi Charles, chinese may be difficult, see our resident language ecxpert, Tom's reply here...
https://discussions.apple.com/message/20061347#20061347
On the slowness...
See if the Disk is issuing any S.M.A.R.T errors in Disk Utility...
http://support.apple.com/kb/PH7029
Open Activity Monitor in Applications>Utilities, select All Processes & sort on CPU%, any indications there?
How much RAM & free Disk space do you have also, click on the Memory & Disk Usage Tabs.
Open Console in Utilities & see if there are any clues or repeating messages when this happens.
In the Memory tab of Activity Monitor, are there a lot of Pageouts?
https://discussions.apple.com/servlet/JiveServlet/showImage/2-18666790-125104/AM Pageouts.jpg

I cannot transfer music to my iPhone4. I just got it and was shown how to do it on iTunes. I managed to transfer photos, but not the music. I tried auto sync and also manyal. Nothing worked - still no music on my iPhone :-(

I cannot transfer music to my iPhone4. I just got it and was shown how to do it on iTunes. I managed to transfer photos, but not the music. I tried auto sync and also manyal. Nothing worked - still no music on my iPhone :-(

http://support.apple.com/kb/HT4527?viewlocale=en_US&locale=en_US

My iphone 4s will not connect to networks. the button is greyed out and cannot turn o. I have reset the network settings and it still does not work - any ideas?

My iphone 4s will not connect to networks. the button is greyed out and cannot turn on. I have reset the network settings and it still does not work - any ideas?

Thank you I tried the reset again did not fix- I think I am down to calling Apple and paying for a tech - phone company says it is a software problem. I just updated to 8.1.3 - I thought the update might fix it.

Replaced internal HD. network and log in password not work.

Replaced internal HD. Used original disc to load the OS. Then rebooted and loaded all my other stuff using my backup drive. Went to log on and my network and log in and both password do not work. Any ideas?
These are passwords I have been using for years. even the password clue is correct.
Please help!
Thank you
Scott

Katrina S. wrote:
+Seriously? No answers at all?+
This is a user forum. Lotsa folks asking questions, few sticking around to give any answers. Just depends who is around to see a message and whether they have any ideas to help. Could take days, not minutes or hours.
+I have created and tried this with three different accounts, but they all fail to enable Home Sharing.+
I'm confused why you're trying 3 different accounts. Try it using the same single account and two different PCs. Does that work? Can you download and play a free song of the week using one of those itunes store accounts?
Going forward, I hope you decide to only use one account. They can never be combined later. You'll have to forever remember the login credentials of each itunes store account if you move stuff to a new PC.
I tried 3 accounts, because none of them work for Apple TV. Yet, all three of them DO access the Apple store and forums and music and everything on this website.
Did I say anything about combining these accounts? Not even remotely helpful.
It's the same for me, as it is for rlongfield22(above).
I am absolutely serious: Apple is the most difficult, ridiculous, illogical interface I have EVER seen in 18 years of computing and using the internet. I use both MACs and PCs daily, so I can easily compare the experiences on many levels.
I know what I am doing on a PC and I rarely make common errors. I know my Apple ID and pass by heart(all three of them). I know my PC and network name by heart. My network and PC have the passwords blank.
So,...I should be able to have my Apple TV work, by simply activating Home Sharing on this network(done that successfully) and then activating it on my Apple TV(doesn't work).
I have tried activating Apple TV network first and tried activating Home Sharing first, but neither one works. When I plug in the Apple TV, the blue light flashes and then stays on.

Auto-Deployment and Restarting Managed Server

Hi,
We are using WebLogic Server 7.0 SP2 on Solaris 8. Yesterday, a developer copied
over a new WAR file into the applications directory. Then he ried to restart the
managed server. This appeared to hang, so he tried restarting the admin. server,
which also failed. Looking at the log, it looks like the admin. server is trying
to deploy apps. from the applications/backup directory.
After I removed the backup directory and edited config.xml to remove all references
to this directory, I was able to startup the Admin. server (though there were
still some errors; see later) and the managed server.
The servers are actually running in "developemnt" mode and have the Aut-Deploy
feature enabled, so my theory is that the auto-deployment was conflicting with
the managed server restart. He shouldn't have had to restart the managed server
since Auto-Deploy is enabled, right?
I'm also wondering about these errors I got when I the Admin. server finally started:
Starting WebLogic Server...
<May 4, 2004 11:41:04 AM MDT> <Notice> <Management> <140005> <Loading configuration
/wlsapp/prod/ivrprod/./config.xml>
<May 4, 2004 11:41:14 AM MDT> <Notice> <Security> <090082> <Security initializing
using realm myrealm.>
<May 4, 2004 11:41:14 AM MDT> <Notice> <WebLogicServer> <000327> <Starting WebLogic
Admin Server "admin" for domain "ivrprod">
<May 4, 2004 11:41:44 AM MDT> <Notice> <Application Poller> <149400> <Activating
application: appsdirbackup_dir>
<May 4, 2004 11:41:49 AM MDT> <Notice> <Application Poller> <149404> <Activate
application appsdirbackup_dir on admin - Running>
<May 4, 2004 11:41:51 AM MDT> <Notice> <Application Poller> <149404> <Activate
application appsdirbackup_dir on admin - Completed>
<May 4, 2004 11:41:54 AM MDT> <Notice> <Management> <141052> <Application Poller
started for development server.>
<May 4, 2004 11:41:54 AM MDT> <Notice> <Application Poller> <149400> <Activating
application: appsdirbackup_dir-0>
<May 4, 2004 11:41:57 AM MDT> <Notice> <Application Poller> <149404> <Activate
application appsdirbackup_dir-0 on admin - Running>
<May 4, 2004 11:41:59 AM MDT> <Notice> <Application Poller> <149404> <Activate
application appsdirbackup_dir-0 on admin - Running>
<May 4, 2004 11:42:02 AM MDT> <Notice> <WebLogicServer> <000365> <Server state
changed to RUNNING>
<May 4, 2004 11:42:02 AM MDT> <Notice> <WebLogicServer> <000360> <Server started
in RUNNING mode>
<May 4, 2004 11:42:13 AM MDT> <Error> <HTTP> <101045> <[ServletContext(id=2268781,name=InternetTroubleshooting,context-path=/backup/
InternetTroubleshooting)] failed to compile /dialogs/ADSLDisambig.jsp, compiler
errors:
/wlsapp/prod/ivrprod/./admin/.wlnotdelete/_appsdir_backup_dir_InternetTroubleshooting_2268781/jsp_servlet/_dialogs/__ADSLDisambig.ja
va:17: package com.nuance.ps.telus does not exist
<May 4, 2004 11:42:20 AM MDT> <Error> <HTTP> <101045> <[ServletContext(id=1642582,name=ReportAPayment,context-path=/backup/ReportAPa
yment)] translation of /dialogs/GetStatus.jsp failed: weblogic.servlet.jsp.JspException:
(line 7): class 'com.nuance.ps.telus.Shared
Storage' could not be loaded>
<May 4, 2004 11:42:20 AM MDT> <Notice> <Application Poller> <149404> <Activate
application appsdirbackup_dir-0 on admin - Running>
<May 4, 2004 11:42:22 AM MDT> <Error> <HTTP> <101045> <[ServletContext(id=3439810,name=TelusLogin,context-path=/backup/TelusLogin)]
translation of /conf/ClearOldKeys.jsp failed: weblogic.servlet.jsp.JspException:
(line 2): class 'com.nuance.ps.telus.SharedStorage'
could not be loaded>
<May 4, 2004 11:42:22 AM MDT> <Error> <Deployer> <149201> <The Slave Deployer
failed to complete the deployment task with id 16 for
the application appsdirbackup_dir.
weblogic.management.ApplicationException: Prepare failed. Task Id = 16
Thanks,
Paul

The short answer to your question is that auto-deployment and multiple
servers don't mix.
If you have a single-server domain and choose to use auto-deployment,
that'll work fine.
Once you have separate admin/managed servers, you need to use
weblogic.Deployer, the wldeploy ant task (8.1), or the console to deploy
applications.
-- Rob
Paul wrote:
Hi,
We are using WebLogic Server 7.0 SP2 on Solaris 8. Yesterday, a developer copied
over a new WAR file into the applications directory. Then he ried to restart the
managed server. This appeared to hang, so he tried restarting the admin. server,
which also failed. Looking at the log, it looks like the admin. server is trying
to deploy apps. from the applications/backup directory.
After I removed the backup directory and edited config.xml to remove all references
to this directory, I was able to startup the Admin. server (though there were
still some errors; see later) and the managed server.
The servers are actually running in "developemnt" mode and have the Aut-Deploy
feature enabled, so my theory is that the auto-deployment was conflicting with
the managed server restart. He shouldn't have had to restart the managed server
since Auto-Deploy is enabled, right?
I'm also wondering about these errors I got when I the Admin. server finally started:
Starting WebLogic Server...
<May 4, 2004 11:41:04 AM MDT> <Notice> <Management> <140005> <Loading configuration
/wlsapp/prod/ivrprod/./config.xml>
<May 4, 2004 11:41:14 AM MDT> <Notice> <Security> <090082> <Security initializing
using realm myrealm.>
<May 4, 2004 11:41:14 AM MDT> <Notice> <WebLogicServer> <000327> <Starting WebLogic
Admin Server "admin" for domain "ivrprod">
<May 4, 2004 11:41:44 AM MDT> <Notice> <Application Poller> <149400> <Activating
application: appsdirbackup_dir>
<May 4, 2004 11:41:49 AM MDT> <Notice> <Application Poller> <149404> <Activate
application appsdirbackup_dir on admin - Running>
<May 4, 2004 11:41:51 AM MDT> <Notice> <Application Poller> <149404> <Activate
application appsdirbackup_dir on admin - Completed>
<May 4, 2004 11:41:54 AM MDT> <Notice> <Management> <141052> <Application Poller
started for development server.>
<May 4, 2004 11:41:54 AM MDT> <Notice> <Application Poller> <149400> <Activating
application: appsdirbackup_dir-0>
<May 4, 2004 11:41:57 AM MDT> <Notice> <Application Poller> <149404> <Activate
application appsdirbackup_dir-0 on admin - Running>
<May 4, 2004 11:41:59 AM MDT> <Notice> <Application Poller> <149404> <Activate
application appsdirbackup_dir-0 on admin - Running>
<May 4, 2004 11:42:02 AM MDT> <Notice> <WebLogicServer> <000365> <Server state
changed to RUNNING>
<May 4, 2004 11:42:02 AM MDT> <Notice> <WebLogicServer> <000360> <Server started
in RUNNING mode>
<May 4, 2004 11:42:13 AM MDT> <Error> <HTTP> <101045> <[ServletContext(id=2268781,name=InternetTroubleshooting,context-path=/backup/
InternetTroubleshooting)] failed to compile /dialogs/ADSLDisambig.jsp, compiler
errors:
/wlsapp/prod/ivrprod/./admin/.wlnotdelete/_appsdir_backup_dir_InternetTroubleshooting_2268781/jsp_servlet/_dialogs/__ADSLDisambig.ja
va:17: package com.nuance.ps.telus does not exist
<May 4, 2004 11:42:20 AM MDT> <Error> <HTTP> <101045> <[ServletContext(id=1642582,name=ReportAPayment,context-path=/backup/ReportAPa
yment)] translation of /dialogs/GetStatus.jsp failed: weblogic.servlet.jsp.JspException:
(line 7): class 'com.nuance.ps.telus.Shared
Storage' could not be loaded>
<May 4, 2004 11:42:20 AM MDT> <Notice> <Application Poller> <149404> <Activate
application appsdirbackup_dir-0 on admin - Running>
<May 4, 2004 11:42:22 AM MDT> <Error> <HTTP> <101045> <[ServletContext(id=3439810,name=TelusLogin,context-path=/backup/TelusLogin)]
translation of /conf/ClearOldKeys.jsp failed: weblogic.servlet.jsp.JspException:
(line 2): class 'com.nuance.ps.telus.SharedStorage'
could not be loaded>
<May 4, 2004 11:42:22 AM MDT> <Error> <Deployer> <149201> <The Slave Deployer
failed to complete the deployment task with id 16 for
the application appsdirbackup_dir.
weblogic.management.ApplicationException: Prepare failed. Task Id = 16
Thanks,
Paul

Help!! Auto-Deploy and Check For Updates in an OPMN-managed instance

I'm trying to use the auto-deploy and check for updates functions in an OAS 10.1.0.3 but I can not make it work.
I don't Know if this functions are only availables for a standalone OC4J instance.
Can anyone help me??
Thanks!!! and sorry for my poor english.

Auto-Deploy is not really designed for an OPMN managed instance -- in earlier releases, this would not even work correctly since deployments where stored in the DCM subsystem and any subsequent configuration changes made via DCM would overwrite the config and you'd lose the "auto-deployed" application.
In 10.1.3.x where DCM is no longer in the picture, and the auto-deploy polling is a function of Oc4J itself, it may work. Be aware that this is not something that is tested in OPMN managed environments.
What configuration changes have you made?
You need to ensure you have modified server.xml so the attribute check-for-updates="all" and you've added the attribute application-auto-deploy-directory and have it pointing at a directory to watch.
-steve-

File & folder sharing with privileges on my network does not work. What is wrong?

My Timecapsule is creating a network between my iMac with OS 10.7.5 and my Macbook Pro Retina OS 10.9.2. I am trying to setup a folder on my iMac with controlled access privileges to work as a server for others using the Macbook as a client. I followed different tutorials to the letter, but it did not work, I could not get the connection. Then I called the Apple help line. It turns out that just setting it up with a 'sharing only' account etc. in 'sharing ' in the 'system preferences' is not enough. One also has to set up the same priviliges in the 'get info' window of the folder directly at the same time...so a double setup. They could not explain properly why and there is no mention of this whatsoever in any tutorial I found on the internet. Anyway, I tried that and it still did not work. When I add the user in the 'get info' window and press enter, suddenly the user does not show up in the privilege box with the user name but instead a line saying something like "searching for user" and something small dudeling next to it......I called Apple again. After two agonizing hours on the phone where I was treated like an imbecile it turns out one has to somehow go through the address book ??? Why, I have no clue and how, I do not remember, but suddenly it worked.
Anyway, now two month later I had to add a new user account to my Macbook and I need to give it access to my server folder on my iMac. Well same problem again. I cannot remeber what we did 2 month ago an cannot call Apple, because my service period has expired. I tried myself and got the dudle in the folders 'get info' window again. Then by mistake I deleted myself as the only administrator account on the Imac from the access privileges to that shaered server folder. When I tried to put my account back into the folders privilege settings I got the same message and the dudeling thingy there too. Frustrated I thought it is best to just re-start the computer.......that was the end of it all: Now the startup window does not show my account name and icon anymore, just two lines to fill in the account name and password. The upper line has an arrow pointing left, the lower for the password an arrow pointing right. I filled in the account name and the password....the dudle circle comes and nothing happens, it seems to crash. When I click on the arrows the sign-in lines disappear, only the three buttons for going to sleep, re-start and turn off at the bottom are the only items left on the screen. I tried 10 times to no avail. This is turning into a nightmare!! My account is the only user account on this iMac.......
What am I doing wrong? Or what is wrong with my iMac?
Why is there nothing mentioned about these issues in the tutorials or anywhere else? Why do the tutorials say it is so easy, when even the staff on Apple's helpline cannot figure it out without having lengthy side conferences with their co-workers and managers???
Does anybody know what I have to do again with the address book to add this external 'sharing only' user account to the folder's privilege settings?
I assumme I have to re-boot my computer tomorrow and restore it from the Time Capsule. How do I do that? I cannot log in????
With the setup I had working for the last two month there were still issues with acces conflict to new subfolders and files inside the shared folder between me and the Macbook account user. I have read that the solution is to create a group and give the group access privileges to the folder. However, I could not find any details on the exact steps to follow. I need the exact steps, otherwise this will turn into the next nightmare. Where can I find this info.
I would really appreciate your help with answers and solutions to these complex issues
Thank you

check out managed datasources in the manuals

Auto Deploy and VCD Network Isolation - Not Working

Similar Messages

Maybe you are looking for