Autonomous AP, 12.3.8JE3. EAP-FAST on local radius failure

Hi all,
I've been trying to configure EAPFAST on Autonomous AP 1242 with the above firmware using local radius. Here are the config:
aaa new
aaa group server radius rad_eap
server x.x.x.x auth 1812 acct 1813
aaa authentication login eap_methods group rad_eap
dot11 ssid EAPFAST
vlan 10
authentication open eap eap_methods
authentication key wpa
int d0
encryption vlan 10 mode cipher aes
ssid EAPFAST
no shut
int d0.10
en do 10
bridge 10
int f0.10
en do 10
bridge 10
int f0.100
en do 100 na
bridge 1
int bvi
ip add x.x.x.x 255.255.255.0
radius-server local
eapfast authority info XYZ
eapfast server-key primary auto
nas x.x.x.x key ####
group FAST
eapfast pac expiry 2 grace 2
username eapfast password eapfast group FAST
radius-server host x.x.x.x auth 1812 acct 1813 key ####
For all my tests, I can get the 7921 phone to work. But using CSSC or even win7 supplicant, I can never get the authentication to go through. I think the eap authentication is stuck at pac provisioning. If i am to manual provision the pac using tftp, it will work. Any clue?
Alvin

Hi,
I was thinking it might be a firmware issue because during some debugs with pac provisoning, there are some errors reporting of some missing cipher suites. I shall try with a new firmware.
Alvin

Similar Messages

EAP-FAST with local radius on 1242AG

I'm trying to get EAP-FAST working using the local radius server on a 1242AG autonomous AP using the latest firmware from Cisco. The cypher I'm using is CCMP. LEAP works fine with all my clients, however if I move to EAP-FAST in the radius config my clients fail to authenticate
I know I need to set PAC to automatic somewhere, but the EAP-FAST configuration in the 1242AG GUI doesn't make this clear what to do.
Any help or a basic example you be great.
thanks,
Simon

I think this is what you're looking for;
Local EAP Authentication on the Wireless LAN Controller with EAP-FAST and LDAP Server Configuration Example
http://www.cisco.com/en/US/products/ps6366/products_configuration_example09186a008093f1b9.shtml
HTH
Regards,
Jatin
Do rate helpful posts~

EAP-FAST on Local Radius Server : Can't Get It Working

Hi all
I'm using an 877w router (flash:c870-advsecurityk9-mz.124-24.T4.bin) as local radius server and have followed various config guides on CCO. LEAP works fine but I just can't get EAP-FAST to work.
I'm testing with win7 client using anyconnect secure mobility client, and also a mac book pro but without luck.
the router sees unknown auth type, and when I run some debugs it talks of unknown eap type 3
sh radius local-server s
Successes              : 1           Unknown usernames      : 0
Client blocks          : 0           Invalid passwords      : 0
Unknown NAS            : 0           Invalid packet from NAS: 17
NAS : 172.27.44.1
Successes              : 1           Unknown usernames      : 0
Client blocks          : 0           Invalid passwords      : 0
Corrupted packet       : 0           Unknown RADIUS message : 0
No username attribute : 0           Missing auth attribute : 0
Shared key mismatch    : 0           Invalid state attribute: 0
Unknown EAP message    : 0           Unknown EAP auth type : 17
Auto provision success : 0           Auto provision failure : 0
PAC refresh            : 0           Invalid PAC received   : 0
Can anyone suggest what I might be doing wrong?
Regs, Tim

Thanks Nicolas, relevant snippets from config:
aaa new-model
aaa group server radius rad_eap
server 172.27.44.1 auth-port 1812 acct-port 1813
aaa authentication login eap_methods group rad_eap
aaa authorization exec default local
aaa session-id common
dot11 ssid home
vlan 3
authentication open eap eap_methods
authentication network-eap eap_methods
authentication key-management wpa
ip dhcp pool home
   import all
   network 192.168.1.0 255.255.255.0
   default-router 192.168.1.1
   dns-server 194.74.65.68 194.74.65.69
ip inspect name ethernetin tcp
ip inspect name ethernetin udp
ip inspect name ethernetin pop3
ip inspect name ethernetin ssh
ip inspect name ethernetin dns
ip inspect name ethernetin ftp
ip inspect name ethernetin tftp
ip inspect name ethernetin smtp
ip inspect name ethernetin icmp
ip inspect name ethernetin telnet
interface Dot11Radio0
no ip address
encryption vlan 1 mode ciphers aes-ccm tkip
encryption vlan 2 mode ciphers aes-ccm tkip
encryption vlan 3 mode ciphers aes-ccm tkip
broadcast-key vlan 1 change 30
broadcast-key vlan 2 change 30
broadcast-key vlan 3 change 30
ssid home
speed basic-1.0 basic-2.0 basic-5.5 6.0 9.0 basic-11.0 12.0 18.0 24.0 36.0 48.0 54.0
station-role root
interface Dot11Radio0.3
encapsulation dot1Q 3
no cdp enable
bridge-group 3
bridge-group 3 subscriber-loop-control
bridge-group 3 spanning-disabled
bridge-group 3 block-unknown-source
no bridge-group 3 source-learning
no bridge-group 3 unicast-flooding
interface Vlan3
no ip address
bridge-group 3
interface BVI3
ip address 192.168.1.1 255.255.255.0
ip inspect ethernetin in
ip nat inside
ip virtual-reassembly
radius-server local
no authentication mac
nas 172.27.44.1 key 0 123456
user test1 nthash 0 B151E8FF684B4F376C018E632A247D84
user test2 nthash 0 F2EEAE1D895645B819C9FD217D0CA1F9
user test3 nthash 0 0CB6948805F797BF2A82807973B89537
radius-server host 172.27.44.1 auth-port 1812 acct-port 1813 key 123456
radius-server vsa send accounting

EAP-TLS and EAP-FAST

Hi NetPro.
EAP-TLS is working now, but how to configure EAP-FAST as the backup in case TLS is failure then user still able to use FAST as the second choice ?
your reply will be highly appreciated.
thanks heaps.
Jack

All you really need to do is enabled EAP-FAST on the Radius server. If you are running a controller environment there isn't any changes on the controller needed. If you are running autonomous make sure you have both "authentication open..." and "authentication network-eap..." configured under the SSID. They only thing that would need to be changed would be the client. You could setup two profiles, one for TLS and the other for EAP-FAST.

Lans/Catalyst and EAP-FAST?

I'd like to use EAP-FAST for both my 802.11 wireless and my lan network.
However the only EAP-FAST client I have seen is the ACU for the Aironet products, nothing for the Catalyst (am I missing something?)
Any plans for Ethernet adapter software that does EAP-FAST? I primary use Windows XP-SP2 in my lan.

All you really need to do is enabled EAP-FAST on the Radius server. If you are running a controller environment there isn't any changes on the controller needed. If you are running autonomous make sure you have both "authentication open..." and "authentication network-eap..." configured under the SSID. They only thing that would need to be changed would be the client. You could setup two profiles, one for TLS and the other for EAP-FAST.

EAP-FAST, local Authentication and PAC provisioning

Hi everybody,
I have a litte understanding problem with the deployment of EAP-FAST.
So here's the deal:
I want to the deploy EAP-FAST with autonomous APs with an ACS as Authentication server. So far so good.
When the ACS is not reachable, the autonomous AP should act as local Authenticator for the clients as backup. Is this possible when doing manual PAC provisioning? I guess not, because the PAC master key is not synced between ACS and the AP local Authenticator.
Would automatic PAC provisioning resolve that issue? If the ACS server fails, the local Authenticator AP will create new PACs for the clients, right?
But - I have doubts regarding automatic provisioning of PACs. From my understanding the Phase-0 is just performed in MS-CHAPv2, which is dictionary attackable. Furthermore a MITM attack could be possible during phase-0.
Would server sided certificates resolve my concerns here?
I would prefer PEAP, but the autonomous APs don't support this EAP type as local authenticator method, right?
Btw. .... is there any good document regarding FAST on CCO? I couldn't find anything. The Q&A page is just scratching the surface. The best document I could find so far is the ACS user configuration page. But I'm not 100% happy with this. Is there some kind of EAP-FAST deployment guide out there? I need best practices regarding PAC provisioning and so on :-)
Thanks in advance!

From what I understand a Internet proxy PAC and a eap-fast PAC are two different purposes.
Is that what you are trying to get clarification on.
Basically eap fast PAC provisioning is a PAC that s provisioned when a client authenticates successfully. The client provides this PAC for network authentication and not proxy authentication.
Sent from Cisco Technical Support iPad App

Mac OS X 10.4.8 adds EAP-FAST support

From the release notes of Mac OS X 10.4.8 update:
http://docs.info.apple.com/article.html?artnum=304200
- Improves security by adding support for EAP-FAST for AirPort wireless authentication.

Mac OS X 10.4.8 is now out, and many people were
hoping that Apple would take the opportunity to
update iSync at the same time.
After examining this update I can confirm that iSync
remains at v2.3 and no new phone support has been
added.
Therefore Sony Ericsson M600, P990 and W950 owners
still have no way to iSync their phones. (For
workarounds
see here.
Owners of Sony Ericsson W850, K610, K510, K800, W300,
W700, K790, V630, Z550 and Z525 phones can continue
to use the iSync Phone Plugins available below to
sync these models:
http://mobile.feisar.com/phoneplugins23.html
Jools
This is really bad news! Apple is disappointing a whole lot of new phone owners. I bought my first Apple computer especially for Isync and Ical. Now it seems that the users are no longer important. Innovation and big numbers are the new targets.
Without the proper use of Ical and Isync, OS X becomes incomplete and therefore less interesting for all users.
I think Apple is making a big mistake here!
I’m not willing to let Apple decide witch phone to buy!
So how about it Steve?
Powerbook G4 Mac OS X (10.4.7)

Connect to EAP-FAST corporate network

Hi. I'm trying to setup my new macbook to connect to my company's wireless network but no luck. Here are the details from my WinXP laptop's Intel PROSet profile:
+Enterprise Security:+
+Wireless Network Name (SSID): protected+
+Network Authentication: Open+
+Data Encryption: CKIP+
+Authentication Type: EAP-FAST+
+Desable EAP-FAST Enhancments (CCXv4): checked+
+Allow unauthenticated provisioning: checked+
+Default server: ACS_wifi+
+User Credentials: Use Windows logon+
+Server Verification is not required.+
*Any idea how to setup my macbook/airport to connect to this network?*
Thanks

I've already did try to create there various profiles but no luck. Even when I try 'Join other network' and select 'Show networks' I don't get my corporate network on the list. Maybe it's hidden. Where I can see a Log what's going on?

WET200 Could firmware allow EAP-FAST

Hi,
I have been looking to utilise the above authentication using a PAC file.
This is the system used by one of our clients. Although Cisco aironet 1300
series supports this, they are a good deal more expensive as a solution.
My question to see what your thought are is whether a device like this WET200
would ever be able to support this type of authentication with the likes of a firmware
upgrade? I know it's not worth holding your breath on, but the unit had originally
been purchased since cisco compatibility was a prerequesite. Only once we went
to setup did it become apparent as to the authentication method they used.
TIA
Andrew

Yes and no. For 2 weeks my iPad would fail every time I tried to connect to the wireless, and I would get the same error message in ACS stating that the supplicant did not respond correctly. Yesterday, I noticed it was connected. I checked the logs in ACS, and saw a successful connection using EAP-FAST. So it did work, but I have no idea why. Nothing changed on either system config wise. Maybe a new PAC file was generated? I need to check the logs to see if that was the case. Regardless, my iPad can now connect using EAP-FAST. Excited about this news, I pushed the profile from the iPhone config utility to 2 additional devices, another iPad, and an iPhone. Both failed, with the same supplicant did not respond correctly message in ACS. So the 3 apple devices have the exact same config on them - 1 now works after 2 weeks of failing, and 2 failed upon first day attempts yesterday. Very odd, and very frustrating. ACS provides very little in the way of help (the supplicant did not respond correctly, but in what way did it not respond correctly??), and the iPad logs even less. So it seems to be impossbile to really know what is going on here. If you or anyone has any suggestions I am definetly open to hearing them.

ISE EAP-FAST chaining EAP-TLS inner method - authorizing against AD

Just a question surrounding EAP-FAST chaining (EAP-TLS inner) and the ability to authorize the username in the CN field of the certificate against AD. As an example for standard EAP-TLS I am able to specifiy that the username should be in a specific AD group. WIth EAP-FAST I seem unable to get the same functionality working - I suspect it is using the combined Chained username to poll with. Any advice would be much appreciated as I would like to differentiate users in different groups whilst retaining the EAP-TLS inner method.

I have found the answer to my own question. In short my issues came down to the way that Microsoft populates the certificate subject fields in particular user certificates and the CN field.
In my deployment I am using a single SSID with the following protocols:
EAP-FAST (EAP-TLS inner) - Certs deployed via AD GPO
EAP-TLS Machine Certs - Certs deploted via AD GPO
EAP-TLS User Certs - Certs deployed via ISE and SCEP (utilising PEAP to auth the user)
EAP-PEAP for Guest and onboarding purposes (no guest portal or MAB - not using the guest portal and CWA is awesome in my opinion).
My certificate profile, created in ISE, utilised the CN field in the subject for principle username. This configuration works fine for machine certs and user certifcates generated via ISE as the CN field is acceptable for matching against AD. The problem however is that the user certs issued by AD GPO etc utilise the AD CN which as I understand cannot be used to ascertain group membership in AD.
The solution seemed obvious - create a new cert profile that utilises the SAN field of the certifcate which is populated with "other name" attributes that can be matched against AD groups. The problem however is that my authentication policy for EAP protocols only allows the selection of one cert profile.... By using the SAN cert profile my EAP-TLS authentications broke but allowed successful auth of the EAP-FAST clients - not a good result.
I figured that the a failure to match the first authentication policy (based on not matching allowed protocol) would then carry on to the next authentication policy allowing me to specifiy a different cert profile - again no dice as the first policy is matched on the wireless 802.1x condition but EAP-FAST protocol was not specified as an allowed protocol and it fails.
The way around this was, lucky in my mind, basically I now match wireless 802.1x condition and Network Access Type:EAP-Chaining which allows me to specify the SAN cert profile for EAP-FAST connections. EAP-TLS obviously does not match the first authentication policy at all as it is not chaining. The subsequent policy is matched for EAP-TLS which specifies the CN cert profile.
I know this explantion is long winded and perhaps obvious to some so for that I apologise. For those of you who are undertaking this and run into the same drama I hope it helps. Feel free to contact me for more information or clarification as this explanation is a mouthful to say the least.

Cisco 871w, radius server local, and leap or eap-fast will not authenticate

Hello, i trying to setup eap-fast or leap on my 871w. i belive i have it confiured correctly but i can not get any device to authenticate to router. Below is the confiureation that i being used. any help would be welcome!
! Last configuration change at 15:51:30 AZT Wed Jan 4 2012 by testtest
! NVRAM config last updated at 15:59:37 AZT Wed Jan 4 2012 by testtest
version 12.4
configuration mode exclusive auto
service nagle
no service pad
service tcp-keepalives-in
service tcp-keepalives-out
service timestamps debug datetime msec localtime show-timezone
service timestamps log datetime msec localtime show-timezone
service password-encryption
service linenumber
service pt-vty-logging
service sequence-numbers
hostname router871
boot-start-marker
boot-end-marker
logging count
logging message-counter syslog
logging buffered 4096
logging rate-limit 512 except critical
logging console critical
enable secret 5 <omitted>
aaa new-model
aaa group server radius rad-test3
server 192.168.16.49 auth-port 1812 acct-port 1813
aaa authentication login default local
aaa authentication login eap-methods group rad-test3
aaa authorization exec default local
aaa session-id common
clock timezone AZT -7
clock save interval 8
dot11 syslog
dot11 ssid test2
vlan 2
authentication open
authentication key-management wpa
guest-mode
wpa-psk ascii 7 <omitted>
dot11 ssid test1
vlan 1
authentication open
authentication key-management wpa
wpa-psk ascii 7 <omitted>
dot11 ssid test3
vlan 3
authentication open eap eap-methods
authentication network-eap eap-methods
no ip source-route
no ip gratuitous-arps
ip options drop
ip dhcp bootp ignore
ip dhcp excluded-address 192.162.16.49 192.162.16.51
ip dhcp excluded-address 192.168.16.33
ip dhcp excluded-address 192.168.16.1 192.168.16.4
ip dhcp pool vlan1pool
   import all
   network 192.168.16.0 255.255.255.224
   default-router 192.168.16.1
   domain-name test1.local.home
   lease 4
ip dhcp pool vlan2pool
   import all
   network 192.168.16.32 255.255.255.240
   default-router 192.168.16.33
   domain-name test2.local.home
   lease 0 6
ip dhcp pool vlan3pool
   import all
   network 192.168.16.48 255.255.255.240
   default-router 192.168.16.49
   domain-name test3.local.home
   lease 2
ip cef
ip inspect alert-off
ip inspect max-incomplete low 25
ip inspect max-incomplete high 50
ip inspect one-minute low 25
ip inspect one-minute high 50
ip inspect udp idle-time 15
ip inspect tcp idle-time 1800
ip inspect tcp finwait-time 30
ip inspect tcp synwait-time 60
ip inspect tcp block-non-session
ip inspect tcp max-incomplete host 25 block-time 2
ip inspect name firewall tcp router-traffic
ip inspect name firewall ntp
ip inspect name firewall ftp
ip inspect name firewall udp router-traffic
ip inspect name firewall pop3
ip inspect name firewall pop3s
ip inspect name firewall imap
ip inspect name firewall imap3
ip inspect name firewall imaps
ip inspect name firewall smtp
ip inspect name firewall ssh
ip inspect name firewall icmp router-traffic timeout 10
ip inspect name firewall dns
ip inspect name firewall h323
ip inspect name firewall hsrp
ip inspect name firewall telnet
ip inspect name firewall tftp
no ip bootp server
no ip domain lookup
ip domain name local.home
ip name-server 8.8.8.8
ip name-server 8.8.4.4
ip accounting-threshold 100
ip accounting-list 192.168.16.0 0.0.0.31
ip accounting-list 192.168.16.32 0.0.0.15
ip accounting-list 192.168.16.48 0.0.0.15
ip accounting-transits 25
login block-for 120 attempts 5 within 60
login delay 5
login on-failure log
memory free low-watermark processor 65536
memory free low-watermark IO 16384
username testtest password 7 <omitted>
archive
log config
logging enable
logging size 255
notify syslog contenttype plaintext
hidekeys
path tftp://<omitted>/archive-config
write-memory
ip tcp synwait-time 10
ip ssh time-out 20
ip ssh authentication-retries 2
ip ssh logging events
ip ssh version 2
bridge irb
interface Loopback0
no ip address
no ip redirects
no ip unreachables
no ip proxy-arp
interface Null0
no ip unreachables
interface FastEthernet0
switchport mode trunk
shutdown
interface FastEthernet1
switchport mode trunk
shutdown
interface FastEthernet2
shutdown
spanning-tree portfast
interface FastEthernet3
spanning-tree portfast
interface FastEthernet4
description Cox Internet Connection
ip address dhcp
ip access-group ingress-filter in
ip access-group egress-filter out
no ip redirects
no ip unreachables
no ip proxy-arp
ip accounting access-violations
ip flow ingress
ip flow egress
ip inspect firewall out
ip nat outside
ip virtual-reassembly
ip tcp adjust-mss 1460
load-interval 30
duplex auto
speed auto
no cdp enable
interface Dot11Radio0
no ip address
no ip redirects
no ip unreachables
no ip proxy-arp
encryption vlan 1 mode ciphers aes-ccm
encryption vlan 2 mode ciphers aes-ccm
encryption key 1 size 128bit 7 <omitted> transmit-key
encryption mode wep mandatory
broadcast-key vlan 1 change <omitted> membership-termination
broadcast-key vlan 3 change <omitted> membership-termination
broadcast-key vlan 2 change <omitted> membership-termination
ssid test2
ssid test1
ssid test3
speed basic-1.0 basic-2.0 basic-5.5 6.0 9.0 basic-11.0 12.0 18.0 24.0 36.0 48.0 54.0
station-role root
rts threshold 2312
no cdp enable
interface Dot11Radio0.1
description <omitted>
encapsulation dot1Q 1 native
no ip redirects
no ip unreachables
no ip proxy-arp
bridge-group 1
bridge-group 1 subscriber-loop-control
bridge-group 1 spanning-disabled
bridge-group 1 block-unknown-source
no bridge-group 1 source-learning
no bridge-group 1 unicast-flooding
interface Dot11Radio0.2
description <omitted>
encapsulation dot1Q 2
no ip redirects
no ip unreachables
no ip proxy-arp
bridge-group 2
bridge-group 2 subscriber-loop-control
bridge-group 2 spanning-disabled
bridge-group 2 block-unknown-source
no bridge-group 2 source-learning
no bridge-group 2 unicast-flooding
interface Dot11Radio0.3
description <omitted>
encapsulation dot1Q 3
no ip redirects
no ip unreachables
no ip proxy-arp
bridge-group 3
bridge-group 3 subscriber-loop-control
bridge-group 3 spanning-disabled
bridge-group 3 block-unknown-source
no bridge-group 3 source-learning
no bridge-group 3 unicast-flooding
interface Vlan1
description <omitted>
no ip address
no ip redirects
no ip unreachables
no ip proxy-arp
ip nat inside
ip virtual-reassembly
bridge-group 1
bridge-group 1 spanning-disabled
interface Vlan2
description <omitted>
no ip address
no ip redirects
no ip unreachables
no ip proxy-arp
ip nat inside
ip virtual-reassembly
bridge-group 2
bridge-group 2 spanning-disabled
interface Vlan3
description <omitted>
no ip address
no ip redirects
no ip unreachables
no ip proxy-arp
ip nat inside
ip virtual-reassembly
bridge-group 3
bridge-group 3 spanning-disabled
interface BVI1
description <omitted>
ip address 192.168.16.1 255.255.255.224
no ip redirects
no ip unreachables
no ip proxy-arp
ip nat inside
ip virtual-reassembly
interface BVI2
description <omitted>
ip address 192.168.16.33 255.255.255.240
no ip redirects
no ip unreachables
no ip proxy-arp
ip nat inside
ip virtual-reassembly
interface BVI3
description <omitted>
ip address 192.168.16.49 255.255.255.240
no ip redirects
no ip unreachables
no ip proxy-arp
ip nat inside
ip virtual-reassembly
ip forward-protocol nd
no ip http server
no ip http secure-server
ip http secure-ciphersuite 3des-ede-cbc-sha rc4-128-sha
ip http timeout-policy idle 5 life 43200 requests 5
ip flow-top-talkers
top 10
sort-by bytes
ip nat inside source list 1 interface FastEthernet4 overload
ip nat inside source static tcp 192.168.16.50 80 interface FastEthernet4 80
ip nat inside source static tcp 192.168.16.50 53 interface FastEthernet4 53
ip nat inside source static tcp 192.168.16.50 3074 interface FastEthernet4 3074
ip nat inside source static udp 192.168.16.50 3074 interface FastEthernet4 3074
ip nat inside source static udp 192.168.16.50 88 interface FastEthernet4 88
ip nat inside source static udp 192.168.16.50 53 interface FastEthernet4 53
ip access-list extended egress-filter
deny   ip any host <omitted>
deny   ip any host <omitted>
deny   ip host <omitted> any
deny   ip host <omitted> any
remark ----- Bogons Filter -----
deny   ip 0.0.0.0 0.255.255.255 any
deny   ip 10.0.0.0 0.10.9.255 any
deny   ip 10.0.0.0 0.10.13.255 any
deny   ip 127.0.0.0 0.255.255.255 any
deny   ip 169.254.0.0 0.0.255.255 any
deny   ip 172.16.0.0 0.15.255.255 any
deny   ip 192.0.0.0 0.0.0.255 any
deny   ip 192.0.2.0 0.0.0.255 any
deny   ip 192.168.0.0 0.0.15.255 any
deny   ip 192.168.0.0 0.0.255.255 any
deny   ip 198.18.0.0 0.1.255.255 any
deny   ip 198.51.100.0 0.0.0.255 any
deny   ip 203.0.113.0 0.0.0.255 any
deny   ip 224.0.0.0 31.255.255.255 any
remark ----- Internal networks -----
permit ip <omitted> 0.0.0.3 any
deny   ip any any log
ip access-list extended ingress-filter
remark ----- To get IP form COX -----
permit udp any eq bootps any eq bootpc
deny   icmp any any log
deny   udp any any eq echo
deny   udp any eq echo any
deny   tcp any any fragments
deny   udp any any fragments
deny   ip any any fragments
deny   ip any any option any-options
deny   ip any any ttl lt 4
deny   ip any host <omitted>
deny   ip any host <omitted>
deny   udp any any range 33400 34400
remark ----- Bogons Filter -----
deny   ip 0.0.0.0 0.255.255.255 any
deny   ip 10.0.0.0 0.255.255.255 any
deny   ip 127.0.0.0 0.255.255.255 any
deny   ip 169.254.0.0 0.0.255.255 any
deny   ip 172.16.0.0 0.15.255.255 any
deny   ip 192.0.0.0 0.0.0.255 any
deny   ip 192.0.2.0 0.0.0.255 any
deny   ip 192.168.0.0 0.0.255.255 any
deny   ip 198.18.0.0 0.1.255.255 any
deny   ip 198.51.100.0 0.0.0.255 any
deny   ip 203.0.113.0 0.0.0.255 any
deny   ip 224.0.0.0 31.255.255.255 any
remark ----- Internal networks -----
deny   ip 10.10.10.0 0.0.0.255 any
deny   ip 10.10.11.0 0.0.0.255 any
deny   ip 10.10.12.0 0.0.0.255 any
deny   ip any any log
access-list 1 permit 192.168.16.0 0.0.0.63
access-list 20 permit 127.127.1.1
access-list 20 permit 204.235.61.9
access-list 20 permit 173.201.38.85
access-list 20 permit 216.229.4.69
access-list 20 permit 152.2.21.1
access-list 20 permit 130.126.24.24
access-list 21 permit 192.168.16.0 0.0.0.63
radius-server local
no authentication mac
eapfast authority id <omitted>
eapfast authority info <omitted>
eapfast server-key primary 7 <omitted>
nas 192.168.16.49 key 7 <omitted>
group rad-test3
vlan 3
ssid test3
user test nthash 7 <omitted> group rad-test3
user testtest nthash 7 <omitted> group rad-test3
radius-server attribute 32 include-in-access-req format %h
radius-server host 192.168.16.49 auth-port 1812 acct-port 1813 key 7 <omitted>
radius-server vsa send accounting
control-plane host
control-plane transit
control-plane cef-exception
control-plane
bridge 1 protocol ieee
bridge 1 route ip
bridge 2 protocol ieee
bridge 2 route ip
bridge 3 protocol ieee
bridge 3 route ip
line con 0
password 7 <omitted>
logging synchronous
no modem enable
transport output telnet
line aux 0
password 7 <omitted>
logging synchronous
transport output telnet
line vty 0 4
password 7 <omitted>
logging synchronous
transport preferred ssh
transport input ssh
transport output ssh
scheduler max-task-time 5000
scheduler allocate 4000 1000
scheduler interval 500
process cpu threshold type total rising 80 interval 10 falling 40 interval 10
ntp authentication-key 1 md5 <omitted> 7
ntp authenticate
ntp trusted-key 1
ntp source FastEthernet4
ntp access-group peer 20
ntp access-group serve-only 21
ntp master 1
ntp server 152.2.21.1 maxpoll 4
ntp server 204.235.61.9 maxpoll 4
ntp server 130.126.24.24 maxpoll 4
ntp server 216.229.4.69 maxpoll 4
ntp server 173.201.38.85 maxpoll 4
end

so this what i am getting now for debug? any thoughs?
010724: Jan 5 16:26:04.527 AZT: RADIUS: Retransmit to (162.168.16.49:1812,1813) for id 1645/2
010725: Jan 5 16:26:08.976 AZT: RADIUS: No response from (162.168.16.49:1812,1813) for id 1645/2
010726: Jan 5 16:26:08.976 AZT: RADIUS/DECODE: No response from radius-server; parse response; FAIL
010727: Jan 5 16:26:08.976 AZT: RADIUS/DECODE: Case error(no response/ bad packet/ op decode);parse response; FAIL
010728: Jan 5 16:26:08.976 AZT: dot11_auth_dot1x_parse_aaa_resp: Received server response: FAIL
010729: Jan 5 16:26:08.976 AZT: dot11_auth_dot1x_parse_aaa_resp: found eap pak in server response
010730: Jan 5 16:26:08.976 AZT: Client d8b3.7759.0488 failed: EAP reason 1
010731: Jan 5 16:26:08.976 AZT: dot11_auth_dot1x_parse_aaa_resp: Failed client d8b3.7759.0488 with aaa_req_status_detail 1
010732: Jan 5 16:26:08.976 AZT: dot11_auth_dot1x_run_rfsm: Executing Action(SERVER_WAIT,SERVER_FAIL) for d8b3.7759.0488
010733: Jan 5 16:26:08.976 AZT: dot11_auth_dot1x_send_response_to_client: Forwarding server message to client d8b3.7759.0488
010734: Jan 5 16:26:08.976 AZT: EAPOL pak dump tx
010735: Jan 5 16:26:08.976 AZT: EAPOL Version: 0x1 type: 0x0 length: 0x0004
010736: Jan 5 16:26:08.976 AZT: EAP code: 0x4 id: 0x1 length: 0x0004
0AD05650:                   01000004 04010004          ........
0AD05660:
010737: Jan 5 16:26:08.980 AZT: dot11_auth_send_msg: sending data to requestor status 1
010738: Jan 5 16:26:08.980 AZT: dot11_auth_send_msg: Sending EAPOL to requestor
010739: Jan 5 16:26:08.980 AZT: dot11_auth_dot1x_send_response_to_client: Started timer client_timeout 30 seconds
010740: Jan 5 16:26:08.980 AZT: dot11_auth_dot1x_send_client_fail: Authentication failed for d8b3.7759.0488
010741: Jan 5 16:26:08.980 AZT: dot11_auth_send_msg: sending data to requestor status 0
010742: Jan 5 16:26:08.980 AZT: dot11_auth_send_msg: client FAILED to authenticate d8b3.7759.0488, node_type 64 for application 0x1
010743: Jan 5 16:26:08.980 AZT: dot11_auth_delete_client_entry: d8b3.7759.0488 is deleted for application 0x1
010744: Jan 5 16:26:08.984 AZT: %DOT11-7-AUTH_FAILED: Station d8b3.7759.0488 Authentication failed
010745: Jan 5 16:26:09.624 AZT: dot11_auth_add_client_entry: Create new client d8b3.7759.0488 for application 0x1
010746: Jan 5 16:26:09.624 AZT: dot11_auth_initialize_client: d8b3.7759.0488 is added to the client list for application 0x1
010747: Jan 5 16:26:09.624 AZT: dot11_auth_add_client_entry: req->auth_type 0
010748: Jan 5 16:26:09.624 AZT: dot11_auth_add_client_entry: auth_methods_inprocess: 2
010749: Jan 5 16:26:09.624 AZT: dot11_auth_add_client_entry: eap list name: eap-methods
010750: Jan 5 16:26:09.624 AZT: dot11_run_auth_methods: Start auth method EAP or LEAP
010751: Jan 5 16:26:09.624 AZT: dot11_auth_dot1x_start: in the dot11_auth_dot1x_start
010752: Jan 5 16:26:09.624 AZT: dot11_auth_dot1x_send_id_req_to_client: Sending identity request to d8b3.7759.0488
010753: Jan 5 16:26:09.624 AZT: EAPOL pak dump tx
010754: Jan 5 16:26:09.624 AZT: EAPOL Version: 0x1 type: 0x0 length: 0x0031
010755: Jan 5 16:26:09.624 AZT: EAP code: 0x1 id: 0x1 length: 0x0031 type: 0x1
0AD05B50:                   01000031 01010031          ...1...1
0AD05B60: 01006E65 74776F72 6B69643D 746F7973 ..networkid=toys
0AD05B70: 6F6E7067 2C6E6173 69643D72 6F757465 onpg,nasid=route
0AD05B80: 72383731 2C706F72 7469643D 30        r871,portid=0
010756: Jan 5 16:26:09.644 AZT: dot11_auth_send_msg: sending data to requestor status 1
010757: Jan 5 16:26:09.648 AZT: dot11_auth_send_msg: Sending EAPOL to requestor
010758: Jan 5 16:26:09.648 AZT: dot11_auth_dot1x_send_id_req_to_client: Client d8b3.7759.0488 timer started for 30 seconds
010759: Jan 5 16:26:09.656 AZT: dot11_auth_parse_client_pak: Received EAPOL packet from d8b3.7759.0488
010760: Jan 5 16:26:09.656 AZT: EAPOL pak dump rx
010761: Jan 5 16:26:09.656 AZT: EAPOL Version: 0x1 type: 0x0 length: 0x0009
010762: Jan 5 16:26:09.656 AZT: EAP code: 0x2 id: 0x1 length: 0x0009 type: 0x1
0B060D50:                   01000009 02010009          ........
0B060D60: 01746573 74                          .test
010763: Jan 5 16:26:09.660 AZT: dot11_auth_dot1x_run_rfsm: Executing Action(CLIENT_WAIT,CLIENT_REPLY) for d8b3.7759.0488
010764: Jan 5 16:26:09.660 AZT: dot11_auth_dot1x_send_response_to_server: Sending client d8b3.7759.0488 data to server
010765: Jan 5 16:26:09.660 AZT: dot11_auth_dot1x_send_response_to_server: Started timer server_timeout 60 seconds
010766: Jan 5 16:26:09.664 AZT: RADIUS/ENCODE(00000198):Orig. component type = DOT11
010767: Jan 5 16:26:09.664 AZT: RADIUS: AAA Unsupported Attr: ssid              [282] 8
010768: Jan 5 16:26:09.664 AZT: RADIUS:   74 6F 79 73 6F 6E                                [toyson]
010769: Jan 5 16:26:09.664 AZT: RADIUS: AAA Unsupported Attr: interface         [175] 3
010770: Jan 5 16:26:09.664 AZT: RADIUS:   36                                               [6]
010771: Jan 5 16:26:09.664 AZT: RADIUS(00000198): Config NAS IP: 192.168.16.49
010772: Jan 5 16:26:09.664 AZT: RADIUS/ENCODE(00000198): acct_session_id: 408
010773: Jan 5 16:26:09.664 AZT: RADIUS(00000198): Config NAS IP: 192.168.16.49
010774: Jan 5 16:26:09.664 AZT: RADIUS(00000198): sending
010775: Jan 5 16:26:09.664 AZT: RADIUS(00000198): Send Access-Request to 162.168.16.49:1645 id 1645/3, len 133
010776: Jan 5 16:26:09.664 AZT: RADIUS: authenticator BF 69 DD DF 89 1F C6 FB - EF EC 12 EB C5 3F 3A CD
010777: Jan 5 16:26:09.664 AZT: RADIUS: User-Name           [1]   6   "test"
010778: Jan 5 16:26:09.664 AZT: RADIUS: Framed-MTU          [12] 6   1400
010779: Jan 5 16:26:09.664 AZT: RADIUS: Called-Station-Id   [30] 16 "0019.3075.e660"
010780: Jan 5 16:26:09.664 AZT: RADIUS: Calling-Station-Id [31] 16 "d8b3.7759.0488"
010781: Jan 5 16:26:09.668 AZT: RADIUS: Service-Type        [6]   6   Login                     [1]
010782: Jan 5 16:26:09.668 AZT: RADIUS: Message-Authenticato[80] 18
010783: Jan 5 16:26:09.668 AZT: RADIUS:   5B FA 47 07 0E E3 4B 71 7F 60 6E 4E 91 37 84 A6 [[?G???Kq?`nN?7??]
010784: Jan 5 16:26:09.668 AZT: RADIUS: EAP-Message         [79] 11
010785: Jan 5 16:26:09.668 AZT: RADIUS:   02 01 00 09 01 74 65 73 74                       [?????test]
010786: Jan 5 16:26:09.668 AZT: RADIUS: NAS-Port-Type       [61] 6   802.11 wireless           [19]
010787: Jan 5 16:26:09.668 AZT: RADIUS: NAS-Port            [5]   6   661
010788: Jan 5 16:26:09.668 AZT: RADIUS: NAS-Port-Id         [87] 5   "661"
010789: Jan 5 16:26:09.668 AZT: RADIUS: NAS-IP-Address      [4]   6   192.168.16.49
010790: Jan 5 16:26:09.668 AZT: RADIUS: Nas-Identifier      [32] 11 "router871"
010791: Jan 5 16:26:14.501 AZT: RADIUS: Retransmit to (162.168.16.49:1645,1646) for id 1645/3
router871#
010792: Jan 5 16:26:19.018 AZT: RADIUS: Retransmit to (162.168.16.49:1645,1646) for id 1645/3
router871#
010793: Jan 5 16:26:23.739 AZT: RADIUS: Retransmit to (162.168.16.49:1645,1646) for id 1645/3
router871#
010794: Jan 5 16:26:28.700 AZT: RADIUS: Fail-over to (162.168.16.49:1812,1813) for id 1645/3
router871#
010795: Jan 5 16:26:33.629 AZT: RADIUS: Retransmit to (162.168.16.49:1812,1813) for id 1645/3
router871#
010796: Jan 5 16:26:38.494 AZT: RADIUS: Retransmit to (162.168.16.49:1812,1813) for id 1645/3
router871#
010797: Jan 5 16:26:39.794 AZT: dot11_auth_parse_client_pak: Received EAPOL packet from d8b3.7759.0488
010798: Jan 5 16:26:39.794 AZT: EAPOL pak dump rx
010799: Jan 5 16:26:39.794 AZT: EAPOL Version: 0x1 type: 0x1 length: 0x0000
0AD053D0:                   01010000                   ....
010800: Jan 5 16:26:39.798 AZT: dot11_auth_dot1x_run_rfsm: Executing Action(SERVER_WAIT,EAP_START) for d8b3.7759.0488
010801: Jan 5 16:26:39.798 AZT: dot11_auth_dot1x_ignore_event: Ignore event: do nothing
router871#
010802: Jan 5 16:26:43.007 AZT: RADIUS: Retransmit to (162.168.16.49:1812,1813) for id 1645/3
router871#
010803: Jan 5 16:26:47.336 AZT: RADIUS: No response from (162.168.16.49:1812,1813) for id 1645/3
010804: Jan 5 16:26:47.336 AZT: RADIUS/DECODE: No response from radius-server; parse response; FAIL
010805: Jan 5 16:26:47.336 AZT: RADIUS/DECODE: Case error(no response/ bad packet/ op decode);parse response; FAIL
010806: Jan 5 16:26:47.336 AZT: dot11_auth_dot1x_parse_aaa_resp: Received server response: FAIL
010807: Jan 5 16:26:47.336 AZT: dot11_auth_dot1x_parse_aaa_resp: found eap pak in server response
010808: Jan 5 16:26:47.336 AZT: Client d8b3.7759.0488 failed: EAP reason 1
010809: Jan 5 16:26:47.336 AZT: dot11_auth_dot1x_parse_aaa_resp: Failed client d8b3.7759.0488 with aaa_req_status_detail 1
010810: Jan 5 16:26:47.336 AZT: dot11_auth_dot1x_run_rfsm: Executing Action(SERVER_WAIT,SERVER_FAIL) for d8b3.7759.0488
010811: Jan 5 16:26:47.336 AZT: dot11_auth_dot1x_send_response_to_client: Forwarding server message to client d8b3.7759.0488
010812: Jan 5 16:26:47.336 AZT: EAPOL pak dump tx
010813: Jan 5 16:26:47.336 AZT: EAPOL Version: 0x1 type: 0x0 length: 0x0004
010814: Jan 5 16:26:47.336 AZT: EAP code: 0x4 id: 0x1 length: 0x0004
0B060710:                   01000004 04010004          ........
0B060720:
010815: Jan 5 16:26:47.340 AZT: dot11_auth_send_msg: sending data to requestor status 1
010816: Jan 5 16:26:47.340 AZT: dot11_auth_send_msg: Sending EAPOL to requestor
010817: Jan 5 16:26:47.340 AZT: dot11_auth_dot1x_send_response_to_client: Started timer client_timeout 30 seconds
010818: Jan 5 16:26:47.340 AZT: dot11_auth_dot1x_send_client_fail: Authentication failed for d8b3.7759.0488
010819: Jan 5 16:26:47.340 AZT: dot11_auth_send_msg: sending data to requestor status 0
010820: Jan 5 16:26:47.340 AZT: dot11_auth_send_msg: client FAILED to authenticate d8b3.7759.0488, node_type 64 for application 0x1
router871#
010821: Jan 5 16:26:47.340 AZT: dot11_auth_delete_client_entry: d8b3.7759.0488 is deleted for application 0x1
010822: Jan 5 16:26:47.344 AZT: %DOT11-7-AUTH_FAILED: Station d8b3.7759.0488 Authentication failed
010823: Jan 5 16:26:47.972 AZT: dot11_auth_add_client_entry: Create new client d8b3.7759.0488 for application 0x1
010824: Jan 5 16:26:47.972 AZT: dot11_auth_initialize_client: d8b3.7759.0488 is added to the client list for application 0x1
010825: Jan 5 16:26:47.972 AZT: dot11_auth_add_client_entry: req->auth_type 0
010826: Jan 5 16:26:47.972 AZT: dot11_auth_add_client_entry: auth_methods_inprocess: 2
010827: Jan 5 16:26:47.972 AZT: dot11_auth_add_client_entry: eap list name: eap-methods
010828: Jan 5 16:26:47.976 AZT: dot11_run_auth_methods: Start auth method EAP or LEAP
010829: Jan 5 16:26:47.976 AZT: dot11_auth_dot1x_start: in the dot11_auth_dot1x_start
010830: Jan 5 16:26:47.976 AZT: dot11_auth_dot1x_send_id_req_to_client: Sending identity request to d8b3.7759.0488
010831: Jan 5 16:26:47.976 AZT: EAPOL pak dump tx
010832: Jan 5 16:26:47.976 AZT: EAPOL Version: 0x1 type: 0x0 length: 0x0031
010833: Jan 5 16:26:47.976 AZT: EAP code: 0x1 id: 0x1 length: 0x0031 type: 0x1
0AD05B50:                   01000031 01010031          ...1...1
0AD05B60: 01006E65 74776F72 6B69643D 746F7973 ..networkid=toys
0AD05B70: 6F6E7067 2C6E6173 69643D72 6F757465 onpg,nasid=route
0AD05B80: 72383731 2C706F72 7469643D 30        r871,portid=0
010834: Jan 5 16:26:47.996 AZT: dot11_auth_send_msg: sending data to requestor status 1
010835: Jan 5 16:26:47.996 AZT: dot11_auth_send_msg: Sending EAPOL to requestor
010836: Jan 5 16:26:47.996 AZT: dot11_auth_dot1x_send_id_req_to_client: Client d8b3.7759.0488 timer started for 30 seconds
010837: Jan 5 16:26:47.996 AZT: dot11_auth_client_abort: Received abort request for client d8b3.7759.0488
010838: Jan 5 16:26:47.996 AZT: dot11_auth_client_abort: Aborting client d8b3.7759.0488 for application 0x1
router871#
010839: Jan 5 16:26:47.996 AZT: dot11_auth_delete_client_entry: d8b3.7759.0488 is deleted for application 0x1
router871#
010840: Jan 5 16:26:58.634 AZT: dot11_auth_add_client_entry: Create new client d8b3.7759.0488 for application 0x1
010841: Jan 5 16:26:58.634 AZT: dot11_auth_initialize_client: d8b3.7759.0488 is added to the client list for application 0x1
010842: Jan 5 16:26:58.638 AZT: dot11_auth_add_client_entry: req->auth_type 0
010843: Jan 5 16:26:58.638 AZT: dot11_auth_add_client_entry: auth_methods_inprocess: 2
010844: Jan 5 16:26:58.638 AZT: dot11_auth_add_client_entry: eap list name: eap-methods
010845: Jan 5 16:26:58.638 AZT: dot11_run_auth_methods: Start auth method EAP or LEAP
010846: Jan 5 16:26:58.638 AZT: dot11_auth_dot1x_start: in the dot11_auth_dot1x_start
010847: Jan 5 16:26:58.638 AZT: dot11_auth_dot1x_send_id_req_to_client: Sending identity request to d8b3.7759.0488
010848: Jan 5 16:26:58.638 AZT: EAPOL pak dump tx
010849: Jan 5 16:26:58.638 AZT: EAPOL Version: 0x1 type: 0x0 length: 0x0031
010850: Jan 5 16:26:58.638 AZT: EAP code: 0x1 id: 0x1 length: 0x0031 type: 0x1
0B060710:                   01000031 01010031          ...1...1
0B060720: 01006E65 74776F72 6B69643D 746F7973 ..networkid=toys
0B060730: 6F6E7067 2C6E6173 69643D72 6F757465 onpg,nasid=route
0B060740: 72383731 2C706F72 7469643D 30        r871,portid=0
010851: Jan 5 16:26:58.658 AZT: dot11_auth_send_msg: sending data to requestor status 1
010852: Jan 5 16:26:58.658 AZT: dot11_auth_send_msg: Sending EAPOL to requestor
010853: Jan 5 16:26:58.658 AZT: dot11_auth_dot1x_send_id_req_to_client: Client d8b3.7759.0488 timer started for 30 seconds
010854: Jan 5 16:27:01.603 AZT: dot11_auth_client_abort: Received abort request for client d8b3.7759.0488
010855: Jan 5 16:27:01.603 AZT: dot11_auth_client_abort: Aborting client d8b3.7759.0488 for application 0x1
010856: Jan 5 16:27:01.603 AZT: dot11_auth_delete_client_entry: d8b3.7759.0488 is deleted for application 0x1
010857: Jan 5 16:27:02.179 AZT: %SEC-6-IPACCESSLOGP: list ingress-filter denied tcp 32.42.41.254(57443) -> 72.201.117.84(59652), 1 packet
010858: Jan 5 16:27:02.179 AZT: %SEC-6-IPACCESSLOGP: list egress-filter denied tcp 22.3.184.118(0) -> 74.125.53.188(0), 4 packets
010859: Jan 5 16:27:12.261 AZT: dot11_auth_add_client_entry: Create new client d8b3.7759.0488 for application 0x1
010860: Jan 5 16:27:12.261 AZT: dot11_auth_initialize_client: d8b3.7759.0488 is added to the client list for application 0x1
010861: Jan 5 16:27:12.261 AZT: dot11_auth_add_client_entry: req->auth_type 0
010862: Jan 5 16:27:12.261 AZT: dot11_auth_add_client_entry: auth_methods_inprocess: 2
010863: Jan 5 16:27:12.261 AZT: dot11_auth_add_client_entry: eap list name: eap-methods
010864: Jan 5 16:27:12.261 AZT: dot11_run_auth_methods: Start auth method EAP or LEAP
010865: Jan 5 16:27:12.261 AZT: dot11_auth_dot1x_start: in the dot11_auth_dot1x_start
010866: Jan 5 16:27:12.261 AZT: dot11_auth_dot1x_send_id_req_to_client: Sending identity request to d8b3.7759.0488
010867: Jan 5 16:27:12.261 AZT: EAPOL pak dump tx
010868: Jan 5 16:27:12.261 AZT: EAPOL Version: 0x1 type: 0x0 length: 0x0031
010869: Jan 5 16:27:12.261 AZT: EAP code: 0x1 id: 0x1 length: 0x0031 type: 0x1
0B060FD0:                   01000031 01010031          ...1...1
0B060FE0: 01006E65 74776F72 6B69643D 746F7973 ..networkid=toys
0B060FF0: 6F6E7067 2C6E6173 69643D72 6F757465 onpg,nasid=route
0B061000: 72383731 2C706F72 7469643D 30        r871,portid=0
010870: Jan 5 16:27:12.285 AZT: dot11_auth_send_msg: sending data to requestor status 1
010871: Jan 5 16:27:12.285 AZT: dot11_auth_send_msg: Sending EAPOL to requestor
010872: Jan 5 16:27:12.285 AZT: dot11_auth_dot1x_send_id_req_to_client: Client d8b3.7759.0488 timer started for 30 seconds
010873: Jan 5 16:27:12.293 AZT: dot11_auth_parse_client_pak: Received EAPOL packet from d8b3.7759.0488
010874: Jan 5 16:27:12.293 AZT: EAPOL pak dump rx
010875: Jan 5 16:27:12.293 AZT: EAPOL Version: 0x1 type: 0x0 length: 0x0009
010876: Jan 5 16:27:12.293 AZT: EAP code: 0x2 id: 0x1 length: 0x0009 type: 0x1
0AD05290:                   01000009 02010009          ........
0AD052A0: 01746573 74                          .test
010877: Jan 5 16:27:12.301 AZT: dot11_auth_dot1x_run_rfsm: Executing Action(CLIENT_WAIT,CLIENT_REPLY) for d8b3.7759.0488
010878: Jan 5 16:27:12.301 AZT: dot11_auth_dot1x_send_response_to_server: Sending client d8b3.7759.0488 data to server
010879: Jan 5 16:27:12.301 AZT: dot11_auth_dot1x_send_response_to_server: Started timer server_timeout 60 seconds
010880: Jan 5 16:27:12.301 AZT: RADIUS/ENCODE(0000019B):Orig. component type = DOT11
010881: Jan 5 16:27:12.305 AZT: RADIUS: AAA Unsupported Attr: ssid              [282] 8
010882: Jan 5 16:27:12.305 AZT: RADIUS:   74 6F 79 73 6F 6E                                [toyson]
010883: Jan 5 16:27:12.305 AZT: RADIUS: AAA Unsupported Attr: interface         [175] 3
010884: Jan 5 16:27:12.305 AZT: RADIUS:   36                                               [6]
010885: Jan 5 16:27:12.305 AZT: RADIUS(0000019B): Config NAS IP: 192.168.16.49
010886: Jan 5 16:27:12.305 AZT: RADIUS/ENCODE(0000019B): acct_session_id: 411
010887: Jan 5 16:27:12.305 AZT: RADIUS(0000019B): Config NAS IP: 192.168.16.49
010888: Jan 5 16:27:12.305 AZT: RADIUS(0000019B): sending
010889: Jan 5 16:27:12.305 AZT: RADIUS(0000019B): Send Access-Request to 162.168.16.49:1645 id 1645/4, len 133
010890: Jan 5 16:27:12.305 AZT: RADIUS: authenticator 6F 6C 63 31 88 DE 30 A2 - C2 06 12 EB 50 A3 53 36
010891: Jan 5 16:27:12.305 AZT: RADIUS: User-Name           [1]   6   "test"
010892: Jan 5 16:27:12.305 AZT: RADIUS: Framed-MTU          [12] 6   1400
010893: Jan 5 16:27:12.305 AZT: RADIUS: Called-Station-Id   [30] 16 "0019.3075.e660"
010894: Jan 5 16:27:12.305 AZT: RADIUS: Calling-Station-Id [31] 16 "d8b3.7759.0488"
010895: Jan 5 16:27:12.305 AZT: RADIUS: Service-Type        [6]   6   Login                     [1]
010896: Jan 5 16:27:12.305 AZT: RADIUS: Message-Authenticato[80] 18
010897: Jan 5 16:27:12.305 AZT: RADIUS:   9D D5 62 1A 38 13 94 30 3A 43 D7 A4 AE A4 43 64 [??b?8??0:C????Cd]
010898: Jan 5 16:27:12.305 AZT: RADIUS: EAP-Message         [79] 11
010899: Jan 5 16:27:12.305 AZT: RADIUS:   02 01 00 09 01 74 65 73 74                       [?????test]
010900: Jan 5 16:27:12.305 AZT: RADIUS: NAS-Port-Type       [61] 6   802.11 wireless           [19]
010901: Jan 5 16:27:12.305 AZT: RADIUS: NAS-Port            [5]   6   664
010902: Jan 5 16:27:12.309 AZT: RADIUS: NAS-Port-Id         [87] 5   "664"
010903: Jan 5 16:27:12.309 AZT: RADIUS: NAS-IP-Address      [4]   6   192.168.16.49
010904: Jan 5 16:27:12.309 AZT: RADIUS: Nas-Identifier      [32] 11 "router871"
010905: Jan 5 16:27:16.642 AZT: RADIUS: Retransmit to (162.168.16.49:1645,1646) for id 1645/4

Cisco ISE with EAP-FAST and PAC provisioning

Hi,
I have search with no result on this topic. So, Does anyone have implemented Cisco ISE authentication with EAP-FAST and PAC provisioning ?
Since I have an issue with internal proxy, user required to authenticate with an internal proxy before granting access to the internet.
If you have any documents, it would be appreciated for me.
Thanks,
Pongsatorn

From what I understand a Internet proxy PAC and a eap-fast PAC are two different purposes.
Is that what you are trying to get clarification on.
Basically eap fast PAC provisioning is a PAC that s provisioned when a client authenticates successfully. The client provides this PAC for network authentication and not proxy authentication.
Sent from Cisco Technical Support iPad App

EAP-FAST - WLC 7.4 Roaming between different FlexConnect (FC) Group

Dear all,
WLC 7.4 Release Notes states that with both Local/Central Switching:
- Mobility in the same Flex Group with CCKM is Fast Roaming if WLAN is mapped to same VLAN
- Mobility between different Flex Group with CCKM cause a Full Auth
Using CCK with EAP-Fast during a call with Cisco IP Phone 7921G and 7925G we notice a gap when roaming from an AP belonging to FC GroupA to an AP belonging to FC Group B...so the only solution to do Fast Romaing is to use PMK(OKC) since CCKM will do a complete authentication each time moving from FC Group.
Where do we enable OKC for a specific WLAN? In the FlexConnect Group Menu?
Thanks a lot for sharing answer and suggestion
BR
O.G.

Hello Scott,
thanks for the explanation...
So if in 7.4.121 OKC is enabled by default I don't understand why I'm having a full Authentication when roaming from AP of FC Group A to AP to FC Group B instead of Fast-Roaming...and this is happening in all FC Group configured (6x).
Should I disable CCKM flag in the WLAN definition?!?!
FC Groups and Mobility
http://www.cisco.com/c/en/us/support/docs/wireless/5500-series-wireless-controllers/112042-technote-product-00.html#anc13
O.G

ACS 5.2 802.1x EAP-FAST w/MSCHAPv2, Cisco WiSM WLC, AD 2008

Hi All,
I'm currently trying to replace an old ACS v3.3 with v5.2.0.26.2.
Looking to authenticate wireless clients with EAP-FAST, MSCHAPv2 inner method against AD.
Coming up against a lot of issues to do with the authentication - no problems on the AD side, but getting the EAP-FAST config right on the ACS is proving difficult.
I found this guide for PEAP-FAST(MSCHAPv2), does anyone know of anything similar for EAP-FAST(MSCHAPv2)?
http://www.cisco.com/image/gif/paws/112175/acs51-peap-deployment-00.pdf
Any guides for ACS 5.x with EAP-FAST would be very helpful, especially to do with certificates, pac provisioning, etc.
Thanks,
Rob

Hello,
Did you find a guide for EAP-FAST with AD ?
I'm facing the same problem, I can't make EAP-FAST working with AD Account,
Thanks to you
Regards,
Gérald

NAC-L2-802.1x (EAP-FAST) and Cisco Secure Services Client 5.0 in wired net

Hi!
(Sorry, if this is a wrong forum.)
Does anybody have any success with Cisco SSC and EAP-FAST in the wired network?
I'm going to use NAC, so I'm trying to set up EAP-FAST. I see the pop-up window on the client to enter user credentials and I see a lot of "debug radius" messages on my 3750 12.2(44)SE switch:
Access-Requests with User-Name="anonymous"
Access-Challenges (I see certificate is sent from ACS)
Access-Reject
CS ACS Failed Attempts Report shows "ACS user unknown" failure for "anonymous".
So far as I understood, EAP-FAST is a tunneled method and it uses "anonymous" to protect user's identity during phase 0 / phase 1 transactions. The actual username is sent in phase 2 transaction.
The following is excerpt from the CS ACS documentation:
"EAP-FAST can protect the username in all EAP-FAST transactions. ACS does not perform user authentication based on a username that is presented in phase one; however, whether the username is protected during phase one depends on the end-user client. If the end-user client does not send the real username in phase one, the username is protected. The Cisco Aironet EAP-FAST client protects the username in phase one by sending FAST_MAC address in place of the username. After phase one of EAP-FAST, all data is encrypted, including username information that is usually sent in clear text."
SSC 5.0 is indeed set up with "Unprotected Identity Pattern"=anonymous and "Protected Identity Pattern"=[username] using sscManagementUtility.exe
So, the question is: Why is ACS 4.1 trying to authenticate username "anonymous" if it knows that the user is fake? Does anybody have working configuaration for EAP-FAST in a wired network?
Any help is greatly appreciated.

Correct, ACS database wasn't selected on the NAP Authentication page. It works now, but I constantly get the following message in the Windows event log: "The Cisco Secure Services Client service hung on starting". This is Windows 2000 Advanced Server system with SP4. SSC was set up with no domain authentication, no machine authentication, single sign-on. After some time the SSC service starts, but at that time my PC is already put into the guest VLAN by the switch (the tx-period is 10 seconds):
POD1-SW#sh run int fa1/0/1
Building configuration...
Current configuration : 378 bytes
interface FastEthernet1/0/1
switchport access vlan 999
switchport mode access
dot1x mac-auth-bypass
dot1x pae authenticator
dot1x port-control auto
dot1x timeout reauth-period server
dot1x timeout tx-period 10
dot1x reauthentication
dot1x critical
dot1x critical recovery action reinitialize
dot1x guest-vlan 91
dot1x critical vlan 11
spanning-tree portfast
end
After all the VLAN is reassigned by the switch, but the delay is too high. How can I troubleshoot this?
Thx.

Autonomous AP, 12.3.8JE3. EAP-FAST on local radius failure

Similar Messages

Maybe you are looking for