Back to the basics... PING

Ok...I have a default configuration on a Cisco 2620 with the FE port configured as IP address 10.10.10.1/24. I've connected my laptop with a x-over cable to the router eth port. My laptop is 10.10.10.2/24 and gateway 10.10.10.1/24. Why am I unable to ping the router from the PC and vice-versa? I've tried multiple cables, different routers and different PCs and I still can't get a ping. A show arp will resolve the PC as well. What am I missing here? Duplex/speed on both are set to auto.

Ok...I've doubled check everything and changed the IP scheme as well...not that it should matter. The link LEDs on the router are lit (Link, FDX, 100). Here is the config, sho int, sho arp and ping results.
Using 671 out of 29688 bytes
version 12.2
service timestamps debug uptime
service timestamps log uptime
no service password-encryption
hostname router
no logging console
enable secret xxxx
enable password cisco1
ip subnet-zero
ip audit notify log
ip audit po max-events 100
interface FastEthernet0/0
ip address 192.168.254.1 255.255.255.0
duplex auto
speed auto
interface Serial0/0
no ip address
shutdown
interface Serial0/1
no ip address
shutdown
interface Serial1/0
no ip address
shutdown
interface Serial1/1
no ip address
shutdown
line con 0
line aux 0
line vty 0 4
password cisco
login
end
FastEthernet0/0 is up, line protocol is up
Hardware is AmdFE, address is 0003.e383.0de0 (bia 0003.e383.0de0)
Internet address is 192.168.254.1/24
MTU 1500 bytes, BW 100000 Kbit, DLY 100 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation ARPA, loopback not set
Keepalive set (10 sec)
Full-duplex, 100Mb/s, 100BaseTX/FX
ARP type: ARPA, ARP Timeout 04:00:00
Last input 00:03:32, output 00:00:08, output hang never
Last clearing of "show interface" counters never
Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0
Queueing strategy: fifo
Output queue: 0/40 (size/max)
5 minute input rate 0 bits/sec, 0 packets/sec
5 minute output rate 0 bits/sec, 0 packets/sec
10 packets input, 1482 bytes
Received 9 broadcasts, 0 runts, 0 giants, 0 throttles
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored
0 watchdog
0 input packets with dribble condition detected
72 packets output, 6598 bytes, 0 underruns
0 output errors, 0 collisions, 0 interface resets
0 babbles, 0 late collision, 0 deferred
0 lost carrier, 0 no carrier
0 output buffer failures, 0 output buffers swapped out
router#sho arp
Protocol Address Age (min) Hardware Addr Type Interface
Internet 192.168.254.2 4 0014.22c7.f0c8 ARPA FastEthernet0/0
Internet 192.168.254.1 - 0003.e383.0de0 ARPA FastEthernet0/0
router#ping 192.168.254.2
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 192.168.254.2, timeout is 2 seconds:
Success rate is 0 percent (0/5)
router#

Similar Messages

Maybe you are looking for

  • Internal table and subtotals

    Hi, I want  to display report output like below . how can i bulid the internal table means can i hardcode the field1. how can i do the subtotals and totals i know the doing subtotals and totals in alv based on some field. field1                      

  • PROBLEMS WITH JAMVOX AND MOUNTAIN LION ?

    I USE THE JAMVOX GUITAR INTERFACE WITH MY MACBOOK PRO. EVERYTHING WAS WORKING HUNKY DORY AFTER UPGRADING TO MOUNTAIN LION...BUT THEN, AFTER ABOUT THREE WEEKS, IT JUST STOPPED WORKING. EVERY TIME I TRY TO START THE PROGRAM NOW,  GET THE SPINNING MAC "

  • HELP!!! Unable to upgrade E50 Firmware!

    Hi, please help me! I cannot update my E50 firmware, eventhough I have the old version 06.27.1.0. NSU connect properly to my phone,without any problem and detect ir correctly.The first time it did, it started to download a 62mB file. But after the do

  • Update adress data of customers

    Hi there, I created a dialog application for creating or changing customer data. The changes must be released by the head of the financial department. The data are stored in separate data tables. When a changed or new customer is released the dialog

  • When I enter a search term in the awesome bar (FF4) it shows me a page load error

    When I for example type in search i get this jar:file:///C:/Program%20Files%20%28x86%29/Mozilla%20Firefox/omni.jar!/chrome/de/locale/browser-region/region.propertiessearch in the awesomebar It also states file not found in the page underneath