Behringer Q502USB Mixer - audio not getting thru to Garageband

Hi folks, I just purchased a Behringer Q502USB mixer to use with Logic and Garageband. I have updated the audio In within system preferences and in that dialog box, I can see the virtual meters responding to the audio input I'm providing. However, once I go into Garageband or Logic, after I select that device as the Input for the audio track, the audio is not being 'heard' by the software so the VU meters do not register and my tracks are silent.
I double-checked Behringer and no additional drivers are required, so I'm sure I've got my bases covered from that perspective.
I just wanted a simple mixer for putting in some scratchpad songs late night on my laptop with an old keyboard and drum machine and I thought this would be a plug-and-play no-brainer, so any guidance would be appreciated.

Did you try, Garageband > Preferences > Audio/Midi and choose the interface.
Logic Pro X > Preferences > Audio > Devices, after choosing input click apply change

Similar Messages

#7590-black ink not getting thru to paper.Changed cartridge/cleaned printhead. Colors ok.

After 2 months of non use, ink not getting thru to paper, sounded as if printhead was working.
There was ink build up at cartridge, cleaned them and printhead. No help.
Changed cartridges. Colors m/y/c came thru but not black.
Any suggestions.

The ink levels reported are those that would occur if the cartridge were printing as expected. If the black is clogged it would appear from the ink guage that ink was being expelled even if it were not. Also, when the color ink is expelled into the service station it will mix and appear black even though it is made of the colors.
As for being a software issue, you can print an internal test page as shown in the troubleshooting document here. That test page is not dependent on the computer, and the driver or other software is not involved. The troubleshooting steps in that document may help resolve the issue. If not I would suggest you Contact HP to discuss your options.
Bob Headrick, HP Expert
I am not an employee of HP, I am a volunteer posting here on my own time.
If your problem is solved please click the "Accept as Solution" button ------------V
If my answer was helpful please click the "Thumbs Up" to say "Thank You"--V

I am unable to configure my ipad 2 with my existing wifi of linksys though I have entered the all ip address as per my laptop but still I am not getting thru network kindly suggest the solution

i am unable to configure my ipad 2 with my existing wifi of linksys though I have entered the all ip address as per my laptop but still I am not getting thru network kindly suggest the solution

The ip-adress cannot be the same as your laptop. You have to make sure that your ip-adress is unique in the network. if your ip is 192.168.1.100 try 192.168.1.112 or somthing. More advanced is to check avalible adress in your router.

HT4623 I try to update ios to 6.1 but it doesn't work and now iphone gone to factory mode from initial stage and upon when am connecting to itune its not getting thru, kindly advice

I try to update ios to 6.1 but it doesn't work and now iphone gone to factory mode from initial stage and upon when am connecting to itune its not getting thru, kindly advice

From the Firefox help files;<BR><BR>
Try disabling graphics hardware acceleration. Since this feature was added to Firefox, it has gradually improved, but there still are a few glitches.

Timeline audio not getting routed to audio out

First, thanks to all who have replied to my previous posts. I'm learning as fast as I can but there's a lot to learn...don'tyaknow!
I have several sequences that are exhibiting the same behavior. Audio plays thru my main monitors if I play the clip from the bin or from the source monitor window. However, the same clip will not play thru my audio monitors once placed on the timeline. The audio meters and the displayed waveform on the timeline show that audio is indeed there, but it is not getting to the speakers. I have a black magic Decklink HD Extreme 3D that is feeding 2 video monitors.   The video monitor that is being fed HDMI is playing back the audio on the timeline, but nothing else.
I have at least one sequence that plays audio from all Premiere sources, including the timeline, so I know it's not a hardware issue. I have used this "working" sequence to compare all audio settings with the "non-working" sequences and can find no obvious differences. Does anyone have an idea what might be happening.
I have checked for differences in:
Preferences
     Audio
     Audio Hardware
     Audio Output Mapping
     and Playback

To the best of my knowledge, BM sequences will only play audio through the BM hardware.

Embedded pictures in g-mail do not get thru when forwarded. Google claims it's a browser problem. how do I fix this?

I'm running Windows 7 Ultimate, Firefox 3.6.16
This problem started up about 4 months ago. I thought it was a Google problem, but Google claims it's a browser problem. The same problem happens with Internet Explorer. I checked the Google website and many people are having this same problem. And Google is totally unresponsive.
Attached pictures go thru fine, but if I get an e-mail from someone with embedded pictures in the message, when I forward that message, the receiver does not get the pictures...only a red X in a blank box.
How can this be fixed?

Hello,
'''Try Firefox Safe Mode''' to see if the problem goes away. Safe Mode is a troubleshooting mode, which disables most add-ons.
''(If you're not using it, switch to the Default theme.)''
* On Windows you can open Firefox 4.0+ in Safe Mode by holding the '''Shift''' key when you open the Firefox desktop or Start menu shortcut.
* On Mac you can open Firefox 4.0+ in Safe Mode by holding the '''option''' key while starting Firefox.
* On Linux you can open Firefox 4.0+ in Safe Mode by quitting Firefox and then going to your Terminal and running: firefox -safe-mode (you may need to specify the Firefox installation path e.g. /usr/lib/firefox)
* Or open the Help menu and click on the '''Restart with Add-ons Disabled...''' menu item while Firefox is running.
[[Image:FirefoxSafeMode|width=520]]
''Once you get the pop-up, just select "'Start in Safe Mode"''
[[Image:Safe Mode Fx 15 - Win]]
'''''If the issue is not present in Firefox Safe Mode''''', your problem is probably caused by an extension, and you need to figure out which one. Please follow the [[Troubleshooting extensions and themes]] article for that.
''To exit the Firefox Safe Mode, just close Firefox and wait a few seconds before opening Firefox for normal use again.''
''When you figure out what's causing your issues, please let us know. It might help other users who have the same problem.''
Thank you.

Hi. I'm trying to get my adobe id account deleted/cancelled & can not get thru. Can someone tell me how I do this? Thanks!

So I cancelled the first & only order I will ever make thru this company & want my account deleted.
I can't get thru to anyone by phone or chat.
Is there no other way to accomplish this?
What happens if I sign out & just never sign back in?
Any help anyone can give would be super appreciated.
Thanks much!

Hi Crystal,
So I cancelled the first & only order I will ever make thru this company & want my account deleted.
I can't get thru to anyone by phone or chat. Is there no other way to accomplish this?
Sorry for this hassle. No, you need to contact them. What is the problem you are facing in contacting them?
What happens if I sign out & just never sign back in?
You might still get charged. Let me know if you still can't get through.
Thanks,
Kevin

AAC Audio Not getting played

Hi,
I am having a .flv video file which contains AAC audio and H.264 Video. Both audio / video in that file gets played out successfully with VLC player. But when trying with adobe flash player plugin v10.0.22.87, only H.264 video is getting played out and AAC audio is not playing.
The AAC encoding was done using FFmpeg.
Can anybody please let me know a solution for playing out the AAC audio?
NOTE: The flv file is attached...
Thanks,
Senthil

As you probably know... System Preferences has nothing to do with Logic.
Logic has it's own audio preferences do you have those set correctly?

It takes forever to make a phone call go thru.Often does not get thru. Hard for others to hear me.

Both iPhone 4 and iPhone 5 in same plan can't place calls or when call goes thru the other person can't hear me. I went to the Verizon store and they are replacing the iPhone 4 but suggested I go to Apple store(ugh!) to get replacement of whic I know they won't have. So I want to know what the heck is going on that both phones have this problem after attempting other phones, in-network, out of network,landlines, etc. I can do my apps, sometimes the texts don't go thru for non-verizon or non-iPhones. I can recieve most emails, twitter but at times even they lag for a day behind. I reboot and that helps.

RLites22,
I can understand your concern about the insurance you have on the line. I want to make sure that I put a fresh pair of eyes on your account to find out exactly what is going on. I did send you a Direct Message. Can you please respond back to me in the direct message so we can go over the account specifics. I really hope to hear back from you soon.
KevinR_VZW
Follow us on Twitter @VZWSupport

Audio not getting to logic

OS 10.9.1 - MBPro 13" / Logic 9. I'm using PreSonus AudioBox 22VSL and system preferences can see audio input. But I can't get any audio into Logic 9! Help! driving me nuts!

As you probably know... System Preferences has nothing to do with Logic.
Logic has it's own audio preferences do you have those set correctly?

Calls are not getting thru in Cisco voice GW for a particular Number

Cisco gateway is connecte to a PBX with an Qsig interface, for a particualr destination number the calls are not gettin estabilished.
the output of the Q931 debug :
Aug 16 16:17:46.145: ISDN Se0/0/0:23 Q931: RX <- SETUP pd = 8 callref = 0x7E05
        Bearer Capability i = 0x8090A2
                Standard = CCITT
                Transfer Capability = Speech
                Transfer Mode = Circuit
                Transfer Rate = 64 kbit/s
        Channel ID i = 0xA98396
                Exclusive, Channel 22
        Facility i = 0x9FAA068001008201008B0100A16E0202070102011530650201010A010
1800101A111A00FA50D0A010212083530303035393938A211A00FA50D0A010212083530303035393
938A312801054454C45434F4D20574F524B524F4F4DA412801054454C45434F4D20574F524B524F4
F4DA50C06062B0C02FF373730020500
        Facility i = 0x9FAA068001008201008B0100A11D0202010002010080144E455453202
F204C4F4E472044495354414E4345
        Calling Party Number i = 0x2183, '8168911010'
                Plan:ISDN, Type:National
        Called Party Number i = 0x89, '18553808521'
                Plan:Private, Type:Unknown
        Sending Complete
Aug 16 16:17:46.149: ISDN Se0/0/0:23 Q931: TX -> CALL_PROC pd = 8 callref = 0xF
E05
        Channel ID i = 0xA98396
                Exclusive, Channel 22
Aug 16 16:17:55.709: ISDN Se0/0/0:23 Q931: TX -> DISCONNECT pd = 8 callref = 0x
FE05
        Cause i = 0x80BF - Service/option not available, unspecified
Aug 16 16:17:55.741: ISDN Se0/0/0:23 Q931: RX <- RELEASE pd = 8 callref = 0x7E0
5
Aug 16 16:17:55.741: ISDN Se0/0/0:23 Q931: TX -> RELEASE_COMP pd = 8 callref =
0xFE05
The Qsig and dial-peer configration :
interface Serial0/0/0:23
no ip address
encapsulation hdlc
isdn switch-type primary-qsig
isdn overlap-receiving
isdn incoming-voice voice
isdn send-alerting
no cdp enable
dial-peer voice 1 voip
description To CBTS GK
destination-pattern +1T
signaling forward rawmsg
session protocol sipv2
session target ipv4:10.9.5.10
session transport tcp
voice-class codec 1
dtmf-relay rtp-nte
no vad
interface Serial0/0/0:23
no ip address
encapsulation hdlc
isdn switch-type primary-qsig
isdn overlap-receiving
isdn incoming-voice voice
isdn send-alerting
no cdp enable
dial-peer voice 1 voip
description To CBTS GK
destination-pattern +1T
signaling forward rawmsg
session protocol sipv2
session target ipv4:10.9.5.10
session transport tcp
voice-class codec 1
dtmf-relay rtp-nte
no vad

Hi Raj,
My name is Edson Pineiro, I understand that your problem description is in regards to failed incoming calls from a qsig trunk.
According to the received q931 setup message I can see the called party number is 18553808521 and as so the gateway should route the dnis based on the best match in destination-pattern. My first suggestion would be to ensure your outgoing dial-peers has a matching destination-pattern that matches the dialed number, for example:
dial-peer voice 1 voip
destination-pattern 1T
The T is a wild card for any digit any length
Or you can be very specific.
dial-peer voice 1 voip
destinaton-pattern 18553808521
The next suggestion would be to ensure that your incoming pots dial-peers contains 'direct-inward dial'. This is so that you don't receive secondary dial tone when dialing in, which I don't think is happening here.
Another suggestion would be to remove 'isdn overlap-receiving' from interface serial 0/0/0:23. Reason being is that the DNIS received is enbloc and not overlapping. You can clearly see that the complete e164 number is received within the setup and no further digits are needed.
But overall the disconnect cause code is 0x80BF the 80 portion is related to the source of the disconnect which is the router and BF "Service/option not available, unspecified" which is described as:
The network or remote equipment cannot provide the service option that the user requests, due to an unspecified reason. A subscription problem can cause this issue.
Any ways seems like the router does not support the protocol or type of message included in the Setup. After decoding one of the facility message:
        Facility i = 0x9FAA068001008201008B0100A16E0202070102011530650201010A010
1800101A111A00FA50D0A010212083530303035393938A211A00FA50D0A010212083530303035393
938A312801054454C45434F4D20574F524B524F4F4DA412801054454C45434F4D20574F524B524F4
F4DA50C06062B0C02FF373730020500
decode -->
Facility IE first byte (protocol profile): 0x9f(Network Extentions), depends on Network Protocol Profile
**Note:
**0x91/0x9f both be used by older qsig spec, including:
**ISO 11582:1995, ETSI 300 239:1993/1995
**newer qsig spec use 0x9f only, including:
**ISO 11582:1995/Cor.1:1999, ECMA 165(4th), ETSI 300 239:2003
**see CSCeb58118 for CCM compatibility issue
NetworkFacilityExtension ::= {
sourceEntity: 0
destinationEntity: 0
NetworkProtocolProfile not present
APDU is a ROSE
0
DivertingLegInformation2Invoke ::= {
invokeID: 1793
operationValue: 21
argument: DivertingLegInformation2Arg ::= {
diversionCounter: 1
diversionReason: 1
originalDiversionReason: 1
divertingNr: PrivatePartyNumber ::= {
privateTypeOfNumber: 2
privateNumberDigits: 50005998
originalCalledNr: PrivatePartyNumber ::= {
privateTypeOfNumber: 2
privateNumberDigits: 50005998
redirectingName: 54 45 4C 45 43 4F 4D 20 57 4F 52 4B 52 4F 4F 4D
originalCalledName: 54 45 4C 45 43 4F 4D 20 57 4F 52 4B 52 4F 4F 4D
Looks like this is a redirected call (call forward or transfer), the redireted number is "50005998" and the other end of the PRI maybe attempting to do either a 2 B channel transfer or B channel optimization, which is not supported certain gateways or needs the use of a tcl scripts. Any ways is it possible to confirm if such features are enabled on the other end of the qsig trunk? and what the number 50005998 is assigned too. This may warrant a TAC case.
However please ensure your carry through the first three configuration changes before looking at the possible bad facility message.
Here are some good documents on ISDN, IOS dial-peers and call legs:
Understanding debug isdn q931 Disconnect Cause Codes
http://www.cisco.com/en/US/tech/tk801/tk379/technologies_tech_note09186a008012e95f.shtml
Configuring Telephony Call-Redirect Features
Two B-Channel Transfer
http://www.cisco.com/en/US/docs/ios/voice/ivr/pre12.3_14_t/configuration/guide/ivrapp.pdf
Understanding Dial Peers and Call Legs on Cisco IOS Platforms
http://www.cisco.com/en/US/partner/tech/tk652/tk90/technologies_tech_note09186a008010ae1c.shtml
Understanding Direct-Inward-Dial (DID) on IOS Voice Digital (T1/E1) Interfaces
http://www.cisco.com/en/US/partner/tech/tk652/tk653/technologies_tech_note09186a00801142f8.shtml
Understanding Inbound and Outbound Dial Peers Matching on IOS Platforms
http://www.cisco.com/en/US/partner/tech/tk652/tk90/technologies_tech_note09186a008010fed1.shtml#prereq
Voice Translation Rules
http://www.cisco.com/en/US/partner/tech/tk652/tk90/technologies_tech_note09186a0080325e8e.shtml
Let me know how you go.
Thanks again for asking the tuff questions.
Cheers
Edson

TS3276 I can send email to myself but all other senders are not getting thru

I can send myself an e-mail but no other senders can get thru

reset the server, re enter your e-mail. go online and find the server title and then enter it in your phone and you should get e-mails. What do you use for e-mail, hotmail, gmail, yahoo mail?

Exporting 6 channel discrete mono tracks (5.1 mix) I only get 2 tracks with compressed audio and 4 empty track on my output.

Exporting 6 channel discrete mono tracks (5.1 mix) I only get 2 tracks with compressed audio and 4 empty track on my output. I'm using Premiere Pro CC14, sequence settings and export setting pasted below. Please help need to export feature trailer for iTunes release next week. Yikes!!!

Thanks for the notes. Im almost there but not quite. I create my sequence 5.1 like you said
then map the dots and LFE. But when I go export media is only give me the option of 1 track 5.1 not 6 discrete channels.
I check my settings and they LOOK right
then I go into my modify clip settings and I see the number of audio tracks as 1 so maybe thats why Im getting only 1 channel 5.1.
But when I select different settings in modify clip environment I can get it to LOOK correct to me
everything seems to be assigned correctly. But when I go back to export it only still gives me the same option of exporting with 5.1 as a single track.

I was working on a project a few days ago and now I'm not getting any audio or visuals out of it. In the project file the screen went grey. Not sure how to fix this. I'm new to iMovie, but the program seems easy to use and my Mac is new. Any help?

I used to use Movie Maker and it would be able to handle lots of file uploads and big projects. I figure iMovie can do the same since it's newer and it's on my iMac. I was working on a project for a few months, it was working fine up until about a few days ago when the project file just stopped working. Not getting any audio or visuals and the screen went grey. I hope to not lose the project file as I've spent a lot of time on it. The project will still show up in iMovie, but it won't play. Other project files will, but this one won't for some reason. It's my first time using this program and I assumed it would be fine, but now it's causing me big problems. Anyone else run into a similar problem?

But it is I jsut can sync, back up files, or anything becuase its stuck at this screene and wont do execute when i click either of those button

I can not get real audio player to record videos from the internet, I believe the problem is that my Firefox browser is set for 64 bi... i need to change it to 32 and do not know how.

I can not get real audio player to record videos from the internet i use firefox as my browser on windows 7, I believe the problem is that my Firefox browser is set for 64 bi... i need to change it to 32 and do not know how.

dont know what to do

Behringer Q502USB Mixer - audio not getting thru to Garageband

Similar Messages

Maybe you are looking for