Bios upgrade and spontaneous shutting down
Hi, I have an s10e, and recently upgraded my bios to 96 version. Right after the upgrade, the computer started shutting itself off without any notification. The shutdown is basically sudden, seems to happen just randomly, but usually takes less than 10min after starting up. Any suggestions/help would be much appreciated. It is a very annoying problem and my computer is practically not usable. I suspect it is the low treshold CPU temperature settting, but the bios does not have an option to manually change this. The fan control programs I got from this website did not help either. Help! Please!
Hi and welcome..
to extract is there a hardware issue or software issue... the answer isnt easy
in normal case... there isnt a dependency of updating BIOS or not... But when u use a program that tried to manipulate hardware special or something.. that could be run into failure...
Starting in BIOS ... press F2 to to get in BIOS press F9 to load setup defaults... change some values you want/or not .. for example Config site ... Quickstart on/off Beep AC On/off ... BOOT settings
Fn-F7 to activate numlock via +/- arrange USB CD to first USB HDD to second HDD to third.. then leave BIOS with F10 save and exit...
Starting windows ... and reduce start up programs to prevent that a program could do the unattended shutdown...
How to do that XP Startup
after this procedure...look is there a wrong setting in Lenovo Energymanagement ...
...still shutdown ... temperature ? getting warm ?
download coretemp to watch temperature ... >over 65 C there is something wrong...
then you can call your local service ....
if temp is not so warm .. and still shutdown ...could be other problem...
sincerely KalvinKlein
Want more ? For further information to get the most of your S-Class machine
Lenovo Energymanagement
Backup
Windows 7
Clean XP Install
XP Startup
Small WebCam Guide
Lenovo Easy Capture
Resolution > 1024 x 576 / 600
Thinkies 2x X200s/X301 8GB 256GB SSD @ Win 7 64
Ideas Centre A520 ,Yoga 2 256GB SSD,Yoga 2 tablet @ Win 8.1
Similar Messages
-
my downloaded apps are not opening, they flash and then shut down. This hapened after i upgraded to the 5.0. How do i fix it!? I've tried everything
You need to resync you applications or redownload them for free via app store. They may be read by your phone, but they are really not there. Re downloading will fix this.
-
HT201401 Safari and Camera spontaneously shut down...help
I have an iPhone 4s. I do all the updates that are available, so I'm at the latest version of iOS available. Safari will open and let me use it, but it spontaneously shuts down frequently...to the point where I don't even use it now, its so irritating. Also the Camera was doing the same thing. I would hit the shutter button and it would shut down. Did that for awhile... couldn't get it to even work to take a picture in a text. Now it won't even open... hit the app and it starts to open and then shuts down. Anyone have similar issues or a solution?
Thanks!Basic troubleshooting from the User's Guide is reset, restart, restore (first from backup then as new). Try each of these in order until the issue is resolved.
-
Mini spontaneous shut-down and application shut-down problem
Help!
I've searched. I've read. I can't find the answer!
After I updated my firmware several weeks ago (to SMC 1.3f4), I've had problems with spontaneous shut-down of the computer, and a frustrating application shut-down issue (Safari, Mail, Word--you name it!).
I tried to find the other firmward update from last summer, which I read about in several posts from July/August, but the link is dead (Mac Mini Firmware update 1.0.1).
Coincidentally, after an office break-in two weeks ago, I FileVaulted my computer. I thought my problem must have to do with that, but all the posts I can find here are about this firmware thing.
Should I/can I reinstall the SMC 1.3f4 update? Is there some secret to the no-longer-available 1.0.1 update?
Can anyone help me? (I would certainly appreciate it!)
Garth
iMac Intel, Mac Mini Intel, Powerbook G4 Mac OS X (10.4.8)Try a safe boot, hold the shift key and power up, this will take a little loner than normal, hold the shift till you see the progress bar. See if it works normal, if it does than it is more than likely some 3rd party software.Then restart normal and check your console for panics. That would be your isssue. You can also start holding command R and restoring from utililities. Back up before you do anything.
-
I just upgraded to Snow Leopard then Lion and the computer shut down after installation.
Now when it starts up it gets as far as the apple icon and then shuts down again
whenever I turn it on it loads that far and then closes.
HELP!Restore your bootable backup/clone or Time Machine backup of Snow Leopard, launch Disk Utility from the install disc, repair the boot volume, and reinstall Lion.
-
After logic board replacement and software update, MacBook Pro is spontaneously shutting down and preventing restart. Inconsistent ability to restart after multiple tries. What is going on?
Hard drive sensor or logic board failure.
Try a SMC Reset, only thing I can help.
http://support.apple.com/kb/ht3964
Check your tones with this sounds like it's not recognizing the RAM, perhaps it's not seated well or making a bad connection or it's defective.
http://support.apple.com/kb/ht1547
Take it back. three times a charm -
My MBP (2007 intel) freezes or spontaneously shuts down and crackling comes from the speakers. Sometimes this happens together all at once? It happens with and without peripherals. Has this happened to anyone else?
It does not seem to be linked to a specific program or periferal use.
I would appreciate if someone can shed some light on this.Run the Apple Hardware Test and swee if any issues are discovered. Also a SMC and PRAM resets may help.
Ciao. -
CMS is unstable and will shut down immediately.
The CMS went down couple of times after windows update on CMS database. Following updates were installed on the SQL database.
KB948109 SQL Server Database Services 2005
KB948109 SQL Server Tools and Workstation Components 2005
KB943109 SQL Server Integration Services 2005
CMS Database Ver: SQL 2005
ODBC Driver Ver for Connecting through Enterprise: 2000.86.1830.00
Error Message:
CMS is unstable and will shut down immediately. Reason: Database access error. Reason [Microsoft][ODBC SQL Server Driver][SQL Server]Incorrect syntax near ')'..
Anyone else facing the same issue ?
Will an ODBC upgrade on Crystal Server fix the issue?Please post this query to the Business Objects Enterprise Administration forum:
BI Platform
That forum is monitored by qualified technicians and you will get a faster response there.
Thank you for your understanding,
Ludek -
Ffox 3.6.10 on a Compaq Evo N8OOv began spontaneously shutting down w/o warning, closing all Internet applications w/ot affecting the operation of the computer, including non-Internet programs running simultaneously. Avira AntiVir Personal and with Spybot gave no hits suggesting infection.
See:
* http://kb.mozillazine.org/Firefox_crashes
* [[Firefox crashes]]
Your above posted system details show multiple Java Console extensions.
You can uninstall (remove) the Java Console extensions and disable the Java Quick Starter extension as you do not need them to run Java applets.
See http://kb.mozillazine.org/Java#Multiple_Java_Console_extensions
See also http://www.java.com/en/download/help/quickstarter.xml - What is Java Quick Starter (JQS)? What is the benefit of running JQS? - 6.0
Disable the Java Quick Starter extension: Tools -> Addons -> Extensions
Control Panel -> Java -> Advanced tab -> Miscellaneous -> Java Quick Starter (disable) -
just had my harddrive replaced and now programs freeze. and imac spontaneously shuts down.
Take it back to where ever the hard drive was replace and tell them what a lousey job they did.
Allan -
Ibook g4 spontaneously shuts down
lately my ibook g4 just shuts down with no warning. it's been happening more often since updating to 10.4.11, though it happened before that as well. and by shut down, i mean the screen goes instantly black and it's off, no warning whatsoever. i have to press the power btn and it then boots normally.
it happens when it's hot... but it also has happened when it's not hot too (after surfing the web for 10 mins the other night).
any ideas what the problem could be? should i install an older version of os x? can i do so without wiping the hd first?I have the same problem. And I haven't done any recent upgrades. It sometimes shuts itself off suddenly only once every few days, and sometimes it's once every few hours. Earlier tonight, it did it three times in about 30 minutes.
The other oddity is that sometimes, pushing the power button doesn't reboot it. It's like the whole system is stuck. I have to unplug the power cable, and completely remove the battery. Then, once I put everything back, THEN I can can reboot it.
And after reboot, a message shows up saying "The system rebooted after an unexpected OS shutdown" or something to that effect.
I'm thinking about taking it to the nearest apple store on Monday, but I really don't want to be without the computer for days or weeks while they diagnose it and fix it. Hopefully someone will have a suggestion. -
Spontaneous shutting down.
My Power iMAc G5 10.4.11 is spontaneously shutting down when I close all open apps.
This has never happened before and energy saver shutdown does not appear active when checked.
I know this is an old iMac and I will be replacing it later this year, but it works fine otherwise and does everything that I need it to.
Any advice?
Many thanks.Have you reset the SMU?
-
I can't shut down my computer because it says mail is open. It says to close mail and continue shut down. Problem is I can't open or close mail now. Can't shut down my computer at all. What can I do?
If you cannot get mail to quit/force quit, you can always remove power from your Mac.
NOTE: removing power is a bad idea, and can result in data loss, but sometimes it is the only thing left to do.
Press and hold the power button for 5 to 10 seconds, and the Mac will power off.
When you power back on, the Mac should reboot. -
I use my PowerPC Quicksilver G4 (2.1), 867 MHz, 1.5 GB standart video card system 10.4.11 to scan (lack of driver for my Mac Pro 10.6.8)
The G4 has been running flawless, now I get kernel panics every time (shut down your computer). When it stays on I get blotched video
left-over spots, tearig and then shut down your computer...
I did all recommended software tests Diskutility, rebuild with DiskWarrior and Apples full Hardware test. Everything comes out fine!
I am at the end of my know how. Thank you for any help
W.W.
I am attaching the latest crashreport:
Unresolved kernel trap(cpu 0): 0x300 - Data access DAR=0x0000000047AC834E PC=0x0000000000821D3C
Latest crash info for cpu 0:
Exception state (sv=0x37D2EA00)
PC=0x00821D3C; MSR=0x00009030; DAR=0x47AC834E; DSISR=0x40000000; LR=0x00821D24; R1=0x21E23B40; XCP=0x0000000C (0x300 - Data access)
Backtrace:
0x00032E98 0x0081AB20 0x0080AC74 0x002E9A80 0x002EB94C 0x0008C248
0x00029234 0x000233F8 0x000ABEAC 0x5038514E
Kernel loadable modules in backtrace (with dependencies):
com.apple.GeForce(4.1.8)@0x7ff000
dependency: com.apple.iokit.IOPCIFamily(1.7)@0x491000
dependency: com.apple.iokit.IOGraphicsFamily(1.4.2)@0x5fc000
dependency: com.apple.iokit.IONDRVSupport(1.4.2)@0x620000
dependency: com.apple.NVDAResman(4.1.8)@0x636000
Proceeding back via exception chain:
Exception state (sv=0x37D2EA00)
previously dumped as "Latest" state. skipping...
Exception state (sv=0x38A98780)
PC=0x9000B348; MSR=0x0200F030; DAR=0x01785000; DSISR=0x42000000; LR=0x9000B29C; R1=0xF0202F20; XCP=0x00000030 (0xC00 - System call)
Kernel version:
Darwin Kernel Version 8.11.0: Wed Oct 10 18:26:00 PDT 2007; root:xnu-792.24.17~1/RELEASE_PPC
panic(cpu 0 caller 0xFFFF0003): 0x300 - Data access
Latest stack backtrace for cpu 0:
Backtrace:
0x000954F8 0x00095A10 0x00026898 0x000A8204 0x000ABB80
Proceeding back via exception chain:
Exception state (sv=0x37D2EA00)
PC=0x00821D3C; MSR=0x00009030; DAR=0x47AC834E; DSISR=0x40000000; LR=0x00821D24; R1=0x21E23B40; XCP=0x0000000C (0x300 - Data access)
Backtrace:
0x00032E98 0x0081AB20 0x0080AC74 0x002E9A80 0x002EB94C 0x0008C248
0x00029234 0x000233F8 0x000ABEAC 0x5038514E
Kernel loadable modules in backtrace (with dependencies):
com.apple.GeForce(4.1.8)@0x7ff000
dependency: com.apple.iokit.IOPCIFamily(1.7)@0x491000
dependency: com.apple.iokit.IOGraphicsFamily(1.4.2)@0x5fc000
dependency: com.apple.iokit.IONDRVSupport(1.4.2)@0x620000
dependency: com.apple.NVDAResman(4.1.8)@0x636000
Exception state (sv=0x38A98780)
PC=0x9000B348; MSR=0x0200F030; DAR=0x01785000; DSISR=0x42000000; LR=0x9000B29C; R1=0xF0202F20; XCP=0x00000030 (0xC00 - System call)
Kernel version:
Darwin Kernel Version 8 Model: PowerMac3,5, BootROM 4.2.5f1, 1 processors, PowerPC G4 (2.1), 867 MHz, 1.5 GB
Graphics: NVIDIA GeForce2 MX, GeForce2 MX, AGP, 32 MB
Memory Module: DIMM0/J21, 512 MB, SDRAM, PC133-333
Memory Module: DIMM1/J22, 512 MB, SDRAM, PC133-333
Memory Module: DIMM2/J23, 512 MB, SDRAM, PC133-333
Modem: Spring, UCJ, V.90, 7.0F, á¸
Network Service: Built-in Ethernet, Ethernet, en0
Parallel ATA Device: WDC WD1200JB-00GVA0, 111.79 GB
Parallel ATA Device: ST3120814A, 111.79 GB
Parallel ATA Device: PIONEER DVD-RW DVR-103
USB Device: Hub in Apple Pro Keyboard, Mitsumi Electric, Up to 12 Mb/sec, 500 mA
USB Device: Apple Optical USB Mouse, Fujitsu Takamisawa Component, Up to 1.5 Mb/sec, 100 mA
USB Device: Apple Pro Keyboard, Mitsumi Electric, Up to 12 Mb/sec, 250 mAThank you for your reply BDAqua.
Yes I ran short and the Extended Test. All pass. One of the first things I did is Safe Boot several times I also repaired permissions. Safe boot takes no longer than before the crashes and as long as I stay in safe boot mode it won't crash. What does that mean?I also ran MacJanitor and removed the SCCUZI card Apple put in when I bought the G4 as well as an M-Audio Delta 66 card which I do not use (both) anymore. I also started up on an external firewire drive 10.4.6. It also (crashes) does the same thing.
I was hoping somebody understands the crash report I enclosed? Isn't that suppose to say what went wrong?
Thank you again for your input BDAqua
W.W. -
My iPhone 5s with iOS 7.1 become very hot when charged almost reach 100 % and will shut down itself. Then I need to off the power and let it cool down first before I can on the phone back. Please help me to solve this problem. Thanks.
Hi Limfromsi,
It is normal to an extent for the iPhone to get warm during charging. If your iPhone is currently in a case, you may want to try charging it without one and see if the issue occurs, as the design of the iPhone uses the exterior of the device as a cooling surface. For more information about iPhones and temperature, you may find the following article helpful:
iOS devices: Keeping device within acceptable operating temperatures
http://support.apple.com/kb/ht2101
If you continue to have issues with your iPhone in the default config (no case, using the included original cable and power adapter), you may want to have your phone evaluated for service. The following page may be of use:
Service Answer Center - iPhone
http://support.apple.com/kb/index?page=servicefaq&geo=United_States&product=ipho ne
Regards,
- Brenden
Maybe you are looking for
-
Conversion of XSTRING to String is incomplete
Hi , I am trying to conver a Xstring to String. But the output string after conversion is incomplete. Here is the code snippet- CALL METHOD CL_ABAP_CONV_IN_CE=>CREATE EXPORTING INPUT = l_xstring ENCODING = 'UTF-8'
-
How to call the data from BW to R/3
HI everybody, I am having one /BIC/OHZSDS_QCAL in the BW which is created by the BW consultant, this /BIC/OHZSDS_QCAL consist of data in it now i have to call this R/3 and create a report to display. i am not getting any idea how to call this /BIC/OH
-
hello i have a trouble with my i phone... i was trying to update a new software and at the end it says that there is some error and i cannot turn my i phone bak on all it shows is itunes logo in the midlle and usb cable with an arrow pointing at the
-
Reg : Enhacement for the transaction code MD04
Hi experts, I have implemented an user exit for the transaction code MD04 where in the stock/requirement list I am supposed to add a new column for the exception number which displays the exception description for the corresponding exception number.
-
1. How can i read the DML's in the redo log? I need the statements from the redo log like we get through LOGMINOR in SQL_REDO column. 2. How to create the archive log file from Redo logs through a command? Means i want to clean the Redo log and want