Block Demand Depend Interfaces between ECC and SCM

Hello All.
Is there a way to block only interfaces of Dependent Demand between ECC and SCM.
I need to do this because ECC writes over my plan in SCM.
Thanks and Best Regards

Hello PrasunM
For example:
When you create an Order on finished material, SCM using PP method "3 - Cover Ind. Requ." creates DepReq on raw material.
SCM using CIF sends PlOrd, PrdOrd and DepReq to ECC. I want send only PlOrd and PrdOrd, DepReq i only need in SCM side.
Best Regards.

Similar Messages

  • Communication between ECC and SCM via XI

    I am trying to set up the scenario 'Purchase_Order_Processing' between
    ECC and SCM using XI. The SCM content for XI has been loaded into XI
    and this scenario is included in the content.
    We are running the following:
    ECC - Version 5.0 - 640 SP level 12
    XI - Version 3.0 - 640 SP Level 14
    SCM - 4.10 - 640 SP Level 12
    The connectivity between the systems has been set up as described in the configuration guides. On sending an IDOC (basic type ORDERS05) into XI I get the following error message 'Http server code 500 reason Internal Server Errorexplanation Error during parsing of SOAP header'.
    The Error XML is as follows:
    <?xml version="1.0" encoding="UTF-8" standalone="yes" ?>
    - <!-- Call Adapter
    -->
    - <SAP:Error xmlns:SAP="http://sap.com/xi/XI/Message/30"
    xmlns:SOAP="http://schemas.xmlsoap.org/soap/envelope/"
    SOAP:mustUnderstand="">
    <SAP:Category>XIAdapter</SAP:Category>
    <SAP:Code area="PLAINHTTP_ADAPTER">ATTRIBUTE_SERVER</SAP:Code>
    <SAP:P1>500</SAP:P1>
    <SAP:P2>Internal Server Error</SAP:P2>
    <SAP:P3>Error during parsing of SOAP header</SAP:P3>
    <SAP:P4 />
    <SAP:AdditionalText />
    <SAP:ApplicationFaultMessage namespace="" />
    <SAP:Stack>Http server code 500 reason Internal Server Error
    explanation Error during parsing of SOAP header</SAP:Stack>
    <SAP:Retry>M</SAP:Retry>
    </SAP:Error>
    Any assistance would be much appreciated.

    Sravya,
    Yes this an IDOC to http scenario. There was no dump at the receiver end. I've found out what was causing the problem - I was using an adapter type of HTTP. It should have been of type 'XI'. I've altered this and it works. Hopefully this will resolve your problem Vinod.
    Richard

  • Best communication between ECC and PI

    Hi All
    SAP is planning to adapt Enterprise Service Architecture (ESA) in the journey towards Service Oriented Architecture (SOA).
    We are working on new implementation project. We have many asynchrounous scenarios. We would like to configure acknowledgements and also like to handle errors effectively.
    Could you please suggest which communication between ECC and PI  is preferrable?
    (Webservices, IDoc, BAPI or RFC)
    Thanks
    Sai

    IDoc, BAPI , rfc - all can be used for seamless communication between ECC and PI. It is totallu dependant on the application and way information is exchanged. For master and transactional data idoc are prefered as for the acknowledgements supported by it. Not sure how effeciently we can handle system and appl ack incase of bapi/rfc. but at the same time idoc will be a drawback for sync comunication where rfc/bapi is preferd. It is SOA or ESA the concepts build in SAP are targeted to serve the enterprise needs where idoc,bapi/rfc are used for servicing the business unit objectives

  • IDocs have disappeared between ECC and PI

    Hi All,
    A couple of days ago 3 idocs went missing between ECC and PI.
    That day 293 idocs of the same message type were sent to the same partner through PI. In PI we only found 290. The 3 IDocs were sent in the same second in the early afternoon. All IDocs before and after were processed correctly.
    The IDocs are unknown in IDX5 and in Runtime Workbench on PI.
    The idocs were not in SM58.
    I found them in WE05, with the correct status. The status update from status = 01 to 30 to 03 took place in the same second.
    25 seconds later, new IDocs of the same message type were created and processed successfully by PI.
    At the time the idocs disappeared there were no problems with either ECC or PI, as far as we know.
    The interface is live for more than 2 years. In the meantime no changes have taken place.
    I have read the links below
    Finding missing IDocs
    Interface Troubleshooting Basics
    It's a mystery to me. Where have those idocs gone?
    Anybody any idea?
    Kind Regards
    Edmond Paulussen

    Hi Edmond,
    On the SAP PI system have a look in transaction IDX5. Take the IDoc number that you could not find in PI and search them in IDX5.
    If you cannot find those IDoc in IDX5 then they never reached PI.
    Regards,
    Jannus Botha

  • Data Inconsistency for 0EMPLOYEE between ECC and BI

    Hi,
    We do a full load to 0EMPLOYEE using 0EMPLOYEE_ATTR from ECC. There were records deleted for lot of employees (some action types) in ECC. This has caused data inconsistency for 0EMPLOYEE master data (time-dependent) between ECC and BI. In BI we have more records for these employees (Additional records have time-dependent range that were deleted from ECC but still exist in BI). These employee records are already being used in lot of InfoProviders. Is there an efficient way to fix this issue? One of the solution is to delete data from all InfoProviders and then delete from Master data for 0EMPLOYEE, but the deletion of employee records can happen quite often, so we don't want to take this route. Also, I tried to re-organize master data attributes for 0EMPLOYEE through process chain, but that didn't work either.
    Message was edited by:
            Ripel Desai

    Hi Ripel,
    I share your pain. This is one of the real pains of Time-Dependant master data in BW. I have been in your exact position and the only way round the issue for me was to clear out all the cubes that used 0EMPLOYEE and then delete and re-load 0EMPLOYEE data.
    I know this responce doesn't help you but at least you are not alone.
    Regards,
    Pete
    http://www.teklink.co.uk

  • Optimize the performance of the RFC call between ECC and CRM

    Hi,
    We are planning to extract sales orders, sales activites and service orders to dispaly it on the  PDF factsheet of the account.
    As of now, the PDF factsheet takes a long time to retrieve the data from ECC to CRM. Can you please suggest us on ways to  optimize the performance of the RFC call between ECC and CRM.
    Thanks in advance,
    Vamsi.

    Hello,
    [SAP Note 636906 |https://service.sap.com/sap/support/notes/636906]is quite useful here.
    Many times, the performance is poor due to function module CRM_CCKPT_EXPORTSUMMARY. This function module gets the customer number, the sales organization and the fact sheet view. If in CRM customizing, you use complete view (001), then all the views in ERP including all the info blocks will be retrieved, which will cause performance issue.
    To solve the issue, please use a limited view to retrieve the data from ERP - especially a view, which does not contain info block 013.
    Hope it helps
    Joaquin

  • ECC and SCM connection

    Hi folks,
    i would like to see ECC and SCM scenarios connected by CIF, how ever HU2(ECC) and HU8 (SCM) systems are not interconnected. let us know whom do we need to contact in this regard.
    Thanks in Advance ...

    Hi Amit,
    The ES (emphasis on Enterprise Service or Web Service) Workplace Systems are actually setup for customers or consultants to test drive SAP delivered Enterprise Services, so it stands to reason that integration between these systems would be using web services / SAP Enterprise services for the most part.
    Trying to contact someone to configure CIF / ALE integration between HU2 and HU8 is not going to work for you.
    Regards, Trevor

  • Communication between ECC and CRM

    Hello,
    I am in phase of showing communication between SAP CRM 5.0 and ECC 6.0.
    I am struggling with finding some simple transactions which are common in both, with which I can show correct connectivity between ECC and CRM.
       I need to save some data from CRM and access the same via transaction within ECC, save some data via ECC and access it via CRM. I already established RFC link between ECC and CRM.
    Probably communication between SD module of ECC with CRM.
    Can you please help me out with this, a clue/correct direction will be of very helpful. Basically I want to know, what transaction I can use for same.
    Any help is really appreciated.
    Thanks
    -Vishal

    Hi Glenn,
          I followed all steps in document mentioned above. In the end during execution of transaction I selected appropriate source and destination, when I click start transfer objects, it gets stuck in waiting phase.
    Among those steps I was not able to perform step#10. Creating Subscriptions for OLTP. My ERP is not displaying this option under subscription wizard. Should it be reason for not starting transfer ? I also do not see ERP logon screen when I select transfer.
    My another question is when transfer will complete, where I'll be able to see transferred objects within ERP database ?
    Thanks
    -Vishal

  • Interface between WM and SD

    Hi,
    Is there anybody who can give me the details of the interface between WM and SD through shipping module?
    It would be nice to have few info about WM /PP and WM/QM.
    Thank you in advance.

    Hi,
    The interface is mainly through the LEWM movement type configuration. You need to define the Interim storage type and movement types required to sales process prior to that.
    After you are done with the above settings, then you can configure for the 2 step picking. If you need it.
    Thanks,
    Mono

  • IDOC Interface between CO and BW

    Hi Gurus
    I am just looking for documents about all interfaces between CO and BW/BI. Can any body supply me these??
    Thanks in advance
    SIM

    Hi Joe-
    There are several How To guides that provide detailed instructions on how to automate transactional and master data loads from NW BW into BPC.  Please check out the following guides:
    [How to Migrate Transactional Data|https://www.sdn.sap.com/irj/scn/go/portal/prtroot/docs/library/uuid/b0427318-5ffb-2b10-9cac-96ec44c73c11]
    and
    [How to Automate Master Data Loads|https://www.sdn.sap.com/irj/scn/go/portal/prtroot/docs/library/uuid/00380440-010b-2c10-70a1-e0b431255827]
    Regards,
    Sheldon

  • Withdrawal Qty don't match between ECC and APO

    Hi Experts.
    I am facing a discrepancy for Withdrawal Qty between ECC and APO before delivery/PGI creation.
    In ECC T.code MD63 I am able to see the withdrawal Qty as expected but in APO a duplicated withdrawal Qty is being created. But this is not happening for all materials, only some specifics materials. I did a check in Material Master data and I have no found any difference between a material that is working and one that is not working...
    Can please somebody explain me why APO is dobling the Withdrawal Qty.
    Thanks a Lot
    Daniel Campos.

    Please check wthether you have dp index duplication in this problem.
    Please follow the process.
    For this process , you need to follow these steps .
    1. From the table /SAPAPO/MATKEY , find the product id of the product for which you feel there is problem .
    2. Find the location id from table /SAPAPO/LOC for the location.
    3. Use the above found 'product id' and 'location id' to find the dp index in table "/SAPAPO/DP_HEAD "  .
    Enter the planning version ' 000 ' in this table . If there is some error you will find multiple entries of the 'dp index ' in this table for the ' 000 ' planning version. If error found use below program to delete the dp index .
    4.  Precaution should be taken before we delete the 'Dp Index' as the consumption history is lost due to this .          In the program  'Z_DEL_WITHDRAWL'  there are 2 check boxes " update " and " list ". List will show the DP index and update will delete it. Need to extremely careful in this program as wrong selection will cause problem .

  • Interface between paravision and labview

    Hi,
    Does any one here who can help or give some idea how to make an interface between paravision and labview software???I need to acquire captured MRI image from paravision and store it to Labview.
    I would appreciate for any kind of assistance.
    Kind Regards,
    Jasim

    Hi Jasim,
    Could I get a little more information about how you are importing the MRI image into LabVIEW?
    1) How are you getting the MRI image into LabVIEW?
    2) What image format will the image be in?
    3) What will you be doing to the image once it is in LabVIEW?
    Best Regards,
    Bill
    Bill E. | Applications Engineer | National Instruments

  • Interface between sockmod and udp

    Hi,
    where can find info on interface between sockmod and udp stream modules. Iam specifically looking for how sockmod and udp/tcp modules inform each other of the destination ip/port numbers, source port number etc... any help would be greatly appreciated.
    Thanks,
    Surya

    Hi,
    In our case we are using
    IDOC-XI--SOAP ( For all Outbound scenarios)
    In this case ask abt wsdl files for SOAP Structure
    HTTPXI--IDOC ( For all Inbound scenarios)
    In this case POS will directly post the message to intergration server direcly by using parameters like namespace , IS details
    Regards
    Seshagiri

  • Difference Between ECCS and BCS

    Hello Everyone
    Can any one explain briefly the difference between ECCS and BCS.
    Your response will be highly appreciated.
    Regards.
    DC

    Quick answer: EC-CS is on the R/3 platform, while BCS is on the BI platform.
    This topic has been discused numerous times - please search the forum for more details if required.

  • Any defference  display icon between ecc and ecc6

    Hi,
    any defference  between ecc and ecc6  to display ICON
    my problem is i was run the one program in ecc  then output shows with icons.
    same program run in ecc6  output is same but ther is no icons like ecc
    Regards
    naresh

    Hi
    Good
    Yes you could find some new icons in between ECC and ECC 6.0 but I dont think there is lots of difference between these two, though you have not mentioned the program name it is hard to give you the correct reply on that, but yes in some standard program cases you may find this kind of problems.
    Thanks
    mrutyun^

Maybe you are looking for