Blue Screen (STOP: 0x00000050) when using multiple Agilent34970A devices with a single GPIB

Hi,
I am using two test fixtures that contain two Agilent34970A Multimeters and two Sorensen Power Supplies (each test fixture is contaning one Multimeter and one Sorensen Power Supply) that are connected via GPIB cables to a single PCI-GPIB card. Below I have attached two VI's. GPIB_Communication_Experiment_1.vi (Test Fixture 1) and
GPIB_Communication_Experiment_2.vi (Test Fixture 2) are used to run self test on the
Agilent34970A multimeters. GPIB_Communication_Experiment_1.vi is talking to one of the Agilent Multimeters and one of the Sorensen Power Supplies (Address 9 for Agilent Multimeter and Address 2 for Sorensen Power Supply) whereas GPIB_Communication_Experiment_2.vi talks to the second Agilent Multimeter and its Sorensen Power Supply (Address 10 for the Multimeter and Address 3 for the Sorense Power Supply).
The Problem occurs when I try to run these two VI's simultaneously where it generates a "blue screen of death" with a Technical Information : STOP: 0x00000050 (0xF8AC00440, 0x00000000, 0x8041889, 0x00000000).
This Problem only occurs when trying to run the executables that were built from the attached VI's.
I have tried to use VISA CLEAR within the while loop as you can see in the VI however it did not improve things.
I have also uninstalled and re-installed the software for my PCI-GPIB card but that seemed not to work either.
At this point I am confused. If I try to run only one Test Fixture at a time I have no problem doing the Self Test on the Agilent Multimeter, yet every single time if I try to run the two test fixtures together I am gettig the blue screen.
Besides the two executable VI's I have also attached the regular VI's
I would really appreciate your help, thanks in advance for your time.
Attachments:
GPIB_Communication_Experiment_1.vi ‏23 KB
GPIB_Communication_Experiment_2.vi ‏23 KB

Hello aps7828:
If I read that correct, you only get the error when you run the executables and not the VIs. Can you take a look at your processor level while one .exe is running. I am wondering if that is the source of the problem.
Regards,
Roland A.
Applications Engineer
National Instruments
Check out VI Roadshow

Similar Messages

Windows XP blue screen and 0x00000050 when starting ITunes up

when starting ITUNES after the upgrade to 7.3, I now get the blue screen of death.
Windows XP service pack 2 is installed
message is STOP: 0x00000050 (0xF8ac0000, 0x00000000, 0xF8ac0000, 0x00000000)
I have installed different video cards and removed my sound card from the system but problem still remains. I did change the QUICKTIME settings as suggested for Vista problems but problem still remains.
ITUNES will only run in SAFE MODE
help please... i miss my music

this is the information from the event log viewer. no files are referenced
Event Type: Error
Event Source: System Error
Event Category: (102)
Event ID: 1003
Date: 8/29/2007
Time: 2:21:22 PM
User: N/A
Computer: DAD_ASUS
Description:
Error code 10000050, parameter1 f79f0000, parameter2 00000000, parameter3 f79f0000, parameter4 00000000.
For more information, see Help and Support Center at http://go.microsoft.com/fwlink/events.asp.
Data:
0000: 53 79 73 74 65 6d 20 45 System E
0008: 72 72 6f 72 20 20 45 72 rror Er
0010: 72 6f 72 20 63 6f 64 65 ror code
0018: 20 31 30 30 30 30 30 35 1000005
0020: 30 20 20 50 61 72 61 6d 0 Param
0028: 65 74 65 72 73 20 66 37 eters f7
0030: 39 66 30 30 30 30 2c 20 9f0000,
0038: 30 30 30 30 30 30 30 30 00000000
0040: 2c 20 66 37 39 66 30 30 , f79f00
0048: 30 30 2c 20 30 30 30 30 00, 0000
0050: 30 30 30 30 0000

Blue Screen of Death when using CVI

Hi,
I am having the blue screen of death happening when I am using LabWindows CVI to control instruments.
I've been using Windows 7, Labwindows CVI/2013 and VISA to control the instruments. Also, there is an Agilent GPIB/USB interface connected to the computer. I've got two errors in the blue screen: PFN_LIST_CORRUPT and PAGE_FAULT_IN_NONPAGED AREA.
The .dmp files point to the Hardware Abstraction Layer and to a USB hub connected to the computer (the forum page did not allow me to attach them).
Regards,
Felipe Fideles

Hi fideles,
I was taking a look at the errors you posted and some of them shows that there are certain files corrupted typically caused by a driver passing a bad memory, so I strongly recommed trying to reinstall the drivers that you are using to communicate with the device.

Windows Blue Screen of Death when using PC Suite

I bought an E63 recently and by it's very nature I need to be able to link it to my laptop for uploading/downloading data. Laptop's a Sony FE11S running XP SP3 which connects successfully with the E63 via cable or Bluetooth. Trouble is, I need to import all of my contacts from the PC to the E63 but in PC Suite, as soon as I click on <contacts> <file> <import> it crashes bringing up the blue screen. Tried all the latest software versions including the E63, tried the Nokia PC Suite removal tools, tried only loading essential (windows) programs and still it crashes! It was over two weeks ago that I contacted Nokia support and all that I've received is a succession of emails (from different people each time) telling me more or less to do the same thing and ignoring my comments and questions, eg. is their a log file somewhere that would tell us where the problem lies? Tried telephone support a couple of times, hung on for 15 minutes each time only to be cut-off . . ! Beginning to regret I bought a Nokia if this is the extent of their so called support . . . unless there's someone out there who might have a clue as to what's going on . . . any help would be much appreciated.

Thanks for that. Screen says:
100.21.110
14-11-2008
RM-437
(c) Nokia E63-1 (223.02)
Going to "Reinstall PC Suite Support" it comes up with a message that says, "PC Suite Support is up to Date".
BUT, I have discovered that turning off Kasperski anti-virus everything springs into life without crashing! So although I can now load my contacts, etc it would be nice to cure the problem so that I don't have to switch Kasperski off everytime I use PC Suite. I tried putting PC Suite in Kasperski as an exception (accepted program) but that didn't help. Any further thoughts? Thanks.

Blue screen after logout when using Open Directory-bound computers

I'm having a weird problem with the Open Directory-bound computers that I'm managing. I recently deployed it to a lab of 30 computers (after doing initial testing with 1 computer), and I'm having one problem in particular:
Sometimes, when a user logs out of one of these OD-bound computers, the login window fails to appear. The user is logged out, the desktop for that user disappears (being replaced with the standard blue desktop), but the login window doesn't appear.
What's strange is that Remote Desktop says these computers are at the login window, and I can manipulate them via Remote Desktop as if nothing is wrong (I can restart, shut down, etc.). But I can't do anything at the computer locally with the keyboard or mouse -- if I try to bring up the shutdown dialog with Control-Power (which works sometimes in these situations), it doesn't work.
This doesn't happen all the time or with the same computers. But it happens often enough that it's a bit of an annoyance -- I usually just restart them from Remote Desktop to get the login window to appear. (The other problem is that sometimes I'm not around to fix it, and so if people come in when I'm not around, they have to force shutdown the computer using the power button and then start it back up to get to the login window.)
I've also noticed that some of the computers have been taking a lot longer to login, which seems to suggest that the computers are trying to access the server or something, but the server is always up and is usually very reliable (with a few exceptions here and there).
Any ideas?
G4 eMacs Mac OS X (10.4.8)

We are having the same problem with our lab of about 30 eMacs. All are computers bound to and managed by the server. Have you found any solutions yet.
Anybody?

Blue Screen of death when using Mozilla 3.6.10 (OK with Chrome)

Been using Netscape and Mozilla for 14 years. Now on 3.6.10 and for last two weeks, it crashes my PC after about 10 minutes online, this is my 4th attempt to report this (system won't stay up long enough). won't relaod session after crash either,
Running Vista unfortunately

Hello Phillip.
It's possible that you are having a problem with some Firefox add-on that is hindering your Firefox's normal behavior. Have you tried disabling all add-ons (just to check), to see if Firefox goes back to normal?
Whenever you have a problem with Firefox, whatever it is, you should make sure it's not caused by one (or more than one) of your installed add-ons, be it an extension, a theme or a plugin. To do that easily and cleanly, run Firefox in [http://support.mozilla.com/en-US/kb/Safe+Mode safe mode] (don't forget to select ''Disable all add-ons'' when you start safe mode). If the problem disappears, you know it's from an add-on. Disable them all in normal mode, and enable them one at a time until you find the source of the problem. See [http://support.mozilla.com/en-US/kb/Troubleshooting+extensions+and+themes this article] for information about troubleshooting extensions and themes and [https://support.mozilla.com/en-US/kb/Troubleshooting+plugins this one] for plugins.
If you need support for one of your add-ons, you'll have to contact its author.
Also, Windows 2000 support has just been dropped (from Microsoft, Firefox 3.5 and 3.6 are still supported for Windows 2000 by Mozilla), so it is recommended that you switch to a supported operating system.
EDIT:
You may want to check for your printer drivers too. If it's only when you print, maybe it crashes because of the drivers... Does the printer work with other software?

Using multiple XML Connectors with a single trigger

I have an application, which I inherited, and it had used a
HUGE XML file, and has not been performing properly. Mgmt accepts
that the size of the XML is the problem and wants it split up, but
have it still work as if it were a single file.
The question posited to me was: Can I set up multiple XML
connectors and have the correct one triggered after a selection is
made from the Combo Box?
I am only an intermediate user and am getting these things
only because the other developer is retiring. Thank you for any
ideas/assistance.

Hello aps7828:
If I read that correct, you only get the error when you run the executables and not the VIs. Can you take a look at your processor level while one .exe is running. I am wondering if that is the source of the problem.
Regards,
Roland A.
Applications Engineer
National Instruments
Check out VI Roadshow

Sand Box has stopped working error when using System Exec.vi with wait until completion is true

I get the following error message in Windows 7 "Sand Box has stopped working" when using System Exec.vi with wait until completion set to true, if I set it to false there is no error message.

Hello JJVerdi
mmm well System Exec.vi simulates a DOS command window, can you run the sandbox from the cmd window using the same commands without any errors?
you may take a look to this KB, it may be related to your issue:
http://digital.ni.com/public.nsf/websearch/2393462BD57B854186256C4F007B706A?OpenDocument
Regards
Mart G

Blue Screen of Death When Plugging in Ipod Touch 4g

Hello,
Im reciving blue screen of death when I plug in my ipod touch 4g. I have updated itunes, Drivers, This happens every time and I suspect it happens when my computer says found new hardware reconizing the ipod as a camera because once I pluged my ipod in and it didn't pop up found camera hardware and it worked. So does anyone know how to fix this or disable my comp from reconizing the ipod as a camera? Thanks in advance
p.s im using XP service pack 3

have u tried pluging an other usb (eg mp3 or mem stick) it to ur compuer? is it doing it with these?
if its only doing this with ur ipod try the following
1 go to start menu and in the search box type in usb
look for device manager
2. open the disk drives and plug in ipod touch and removeable disk should show up
3, try usb drives updates
because the ipod has a camera most older computers running xp think its a camera,
if u have and usb mem stick copy ur itunes folder on to it and copy it to a computer running vista or windows 7 and c it its doing it on one of them, if its doing it on one them there may be other hardware isues with ur ipod touch

Blue screen of death when syncing verizon I phone

I receive a blue screen of death when I try to sync my I phone 4 with I tunes on my laptop. The initial sync went fine, I am connected to my Exchange server for email and have downloaded CD's to I Tunes, when I try to sync...blue screen. I have run registry fix and virus programs and have no errors. Does anyone know how to fix this?

The first response was correct, the computer (xps 1210) used a logitech camera driver that I did not recognize so I deleted it. The software was still active and crashed the computer. Fix was reinstall logitech software and driver. Updating the driver would have probably worked. Thank you!

Blue screen of death when La Cie external firewire drive connected

I tested a LaCie external firewire drive on my iMac and it worked fine. I packed it up well and posted it to a friend who gets the blue screen of death when the LaCie is connected to her iMac. She's not even trying to boot from it.
My iMac is 9.1 and hers is 8.1. We are both running Snow Leopard. Was there some problem once upon a time with chipsets or am I mis-remembering?
TIA

Create an ISO (Encore) or folder on your hard drive (Encore or Premiere Elements) and then use the FREE http://www.imgburn.com/index.php?act=download to write files or folders or ISO to disc for DVD or BluRay (send the author a PayPal donation if you like his program)
Imgburn will read the ACTUAL disc brand from the disc, which is not always the same as the box label (Memorex is notorious for buying "anything" and putting it inside a Memorex box)
When you write to disc with Imgburn, use the SLOWEST possible speed setting, so your burner has the best chance to create "good, well formed" laser burn holes... since no player is required to read a burned disc, having a "good" one from a high quality blank will help

Blue screen of death when accessing Itunes store

Whenever I click on the Itunes store, the computer crashes and I get blue screen of death.

You haven't given your operating system.
If you are getting a blue screen stop, it would help if you could post the exact error message. It should be some sort of numbers and text -
0x(zeros/letters/numbers) (CAPSANDUNDERSCORES)
For example:
Stop 0x05 (INVALIDPROCESS_ATTACHATTEMPT)
Also *is a file name mentioned* in the error message? If so give the exact file name
if you're not seeing a blue screen (or just a flash of one), you can use this technique to make hidden blue screens appear:
1) Open your system control panel (Start->Control Panels->System).
2) Select the "Advanced" tab.
3) Click the "Settings" button in the "Startup and Recovery" section
4) Verify that under "System Failure" the "Automatically restart" checkbox is not checked.
There is some general help on Troubleshooting Windows Stop Messages here:
http://aumha.org/win5/kbestop.htm

Macmini 2011 on lion, goes to a blue screen om monitor when awakening from sleep mode, last 3 or 4 seconds, can anyone help? Thanks

Macmini 2011 on lion, goes to a blue screen on monitor when awakening from sleep mode, last 3 or 4 seconds, before desktop appears, can anyone help? Thanks

Depending on the system configuration, this may not
be unusual. The Mini that I use for my home theater,
which is connected to a receiver then to a TV, all via
HDMI usually takes a couple seconds to come up just
the way yours does. Same happens when I switch sources
on the receiver. Actually, it starts with the blue screen and
will sometimes flash before the desktop comes up.
It seems that when HDMI goes dormant, there is handshaking
that needs to be re-established, at least thats my SWAG on it.
On the other hand, the Mac Mini Server that I use as a work
station and is connected to a Thunderbolt Display, wakes to desktop
in a second, maybe two. On this combo, it just comes up to
the desk top.
It also probably depends on what processes were active when
the Mini was put to sleep. So it may take some time for it to get around
to reloading the desktop.

When using my ipad air it keeps coming off the page I'm on or app and going back to the home screen. Also when using my ipad the screen will go white with a black apple icon in the middle for about 20 seconds then it makes a ping

When using my ipad air it keeps coming off the page I'm on or app I am using and going back to the home screen. Also when using my ipad the screen will go white with a black apple icon in the middle for about 20 seconds then it makes a ping sound and goes to the home screen. Could anyone help please. Thank you :-)

Read here:
http://help.apple.com/ipad/8/#/iPad9a245e3e

Blue Screen of Death when connecting ipod

Ever since the 2.0 update, when I try and connect my ipod about 50% of the time i get the BSOD. What the heck is going on? Is it another 2.0 bug?

The following document is worth checking through:
What to do when Windows XP or Vista computer displays a blue screen error message when syncing the iPhone or iPod touch

Blue Screen (STOP: 0x00000050) when using multiple Agilent34970A devices with a single GPIB

Similar Messages

Maybe you are looking for