Blue screen with *** STOP: 0x000000A5 (0x0001000A, 0x00000000, 0x00000000, 0x00000000)

HP Pavillion Elite m9150f PC
Windows 7
When I try to start my computer, I get a screen "Windows Error Recovery" and two choices "Launch Startup Repair (recommended)" and "Start Windows Normally". No matter which one I choose, I get a blue screen with "*** STOP:   0x000000A5 (0x0001000A, 0x00000000, 0x00000000, 0x00000000)".  I can't go any further. Then, I turn off the computer.
I restart the computer and choose F9-Diagnotics. When this opens. I see that the memory test has failed and has an error code of "BIOME-1"  and the suggestion to "Please contact HP Support".
Prior to all of this happening, I reinstalled an antivirus program that I've been using for several years with no problems.
So here I am.
What do I do now?
I'd appreciate your help.
Thank you.
Chris
This question was solved.
View Solution.

Here is the user guide. http://h10032.www1.hp.com/ctg/Manual/c01152947.pdf
Page 26 is the start of "Replacing memory"
{---------- Please click the "Thumbs Up" to say thanks for helping.
Please click "Accept As Solution" if my help has solved your problem. ----------}
This is a user supported forum. I am a volunteer and I do not work for HP.

Similar Messages

Blue screen with error code and I have no recovery disks for HP Pavilion dv6-1260se

I have a HP Pavilion dv6-1260se with factory installed operating system of Vista. When booting up the computer, I receive a blue screen with this error message: STOP: c000021a {Fatal System Error}.
                                                            The verification of a KnownDLL failed. system process terminated unexpectedly with
                                                             a status of 0x0000221 (0x007fb9c0 0x00000000).
                                                             The system has been shut down.
I do not have recovery disks for this computer. I tried to order them but them seem to not be available. This is my daughter's computer. She says she started to have trouble after downloading Frost Wire (music share) and then she removed it. We tried going back to an earlier time and that didn't help and then the blue screen with error message appeared. What do I do now?
This question was solved.
View Solution.

Hi,
Assuming your in the US, recovery discs are available to order for that model here. That may be the best option.
You should also be able to do a recovery without the discs as well. Take a look at this document: Recover Windows Vista Operating System Using HP Recovery, and look for the section Restore the PC to its original condition with the HP Recovery Manager if Windows Vista is not accessible. This should allow you to recover the PC.
R
Although I am an HP Employee, I am speaking for myself and not for HP.

Blue screen with the following error SYSTEM SERVICE EXCEPTION (ACPL.sys)

Hi,
I had a blue screen with SYSTEM SERVICE EXCEPTION (ACPL.sys) error message yesterday.
It happened right after the graphic card update was completed. I have an HP Spectre XT laptop with Windows 8 and Intel(R) HD Graphics 4000.
After restart, I noticed that the available free space on my hard disk dropped by 4 GB!
Can you please assist?
Thank you.

We do need the actual DMP file as it contains the only record of the sequence of events leading up to the crash, what drivers were loaded, and what was responsible.
WE NEED AT LEAST TWO DMP FILES TO SPOT TRENDS AND CONFIRM THE DIAGNOSIS.
You may be able to get the DMP files without crashing by booting into safe mode (F8) with networking.
If you are overclocking stop. (chances are if you dont know if you are, you are not)a
To enable us to assist you with your computer's BSOD symptoms, upload the contents of your "\Windows\Minidump" folder. We need at least 2 DMP FILES to diagnose and confirm
The procedure:
* Copy the contents of \Windows\Minidump to another (temporary) location somewhere on your machine.
* Zip up the copy.
* Attach the ZIP archive to your post using the "paperclip" (file attachments) button. (if available on your site, MS doesnt have this)
*Please upload them to a file sharing service like Skydrive or"Rapidshare" and put a link to them in your reply.
Link for how to upload below.
http://www.wikihow.com/Use-SkyDrive
To ensure minidumps are enabled:
* Go to Start, in the Search Box type: sysdm.cpl, press Enter.
* Under the Advanced tab, click on the Startup and Recovery Settings... button.
* Ensure that Automatically restart is unchecked.
* Under the Write Debugging Information header select Small memory dump (256 kB) in the dropdown box (the 256kb varies).
* Ensure that the Small Dump Directory is listed as %systemroot%\Minidump.
* OK your way out.
* Reboot if changes have been made.
Please also run MSinfo32 and upload the output as well.
To run MSinfo32 please go to start>run>MSinfo32
Go to "file" "save" and upload the saved file with the DMPS
System specs are extremely useful so please include whatever you know.
Blue Screen View & Who Crashed are often wrong and should only be used in an emergency
Team Zigzag3143.com
Wanikiya & Dyami--Team Zigzag

Blue Screen error STOP:0x0000001E erro

Hi,
Have i have getting blue screen error (STOP:0x0000001E) on windows server R2 standard edition.
Server is working only in safe mode with networking but not normally.
Due to which server is getting rebooted again and again..please help.
suhasish

Hi,
Thanks for your posting. I agree with Paul, since it is not related to Windows Server Technical Preview, I will move it to the Windows
server general forum. Thanks for your understanding and support.
According to the error message, you may need a dump file to narrow down the root cause of the issue. You can analyze
the dump file with Debugging Tools. For more detailed information, please refer to the KB below:
How to read the small memory dump files that Windows creates for debugging
Unfortunately, it is not effective for us to debug the crash dump file here in the forum. Therefore, I would
like to suggest that you contact Microsoft Customer Service and Support (CSS) via telephone so that a dedicated Support Professional can assist with your request.
To obtain the phone numbers for specific technology request, please refer to the website listed below:
http://support.microsoft.com/default.aspx?scid=fh;EN-US;PHONENUMBERS
If you are outside the US, please refer to
http://support.microsoft.com
for regional support phone numbers.
Hope the issue will be resolved soon. In addition, I would appreciate it if can share the resolution when the
problem is resolved. Thanks for your understanding and support.
Best regards,
Susie

Stuck on blue screen with clouds rainbow, floated ...

As it says.
When I start Skype, it goes straight to a blue screen with blue clouds and a green rainbow at the bottom. I get no prompt to login. I have followed various guides, such as renaming login to login1, deleting login, restarting the computer, uninstalling then installed skype (which gets me an error code 2734 I think), uninstalled and installed Internet Explorer. I have run windows update and everything is up to date. I also followed the advise in the floated topic, and even after using Command Prompt (which was not in Accessories folder, had to search cmd to find it) and restarting, the 'click this button' does not work.
Skype was working fine on Sunday, and now it is broken. The only thing I have done in the meantime is run a repair tool for Windows Media Player as a game I installed required it to play in game music.
EDIT: I use Windows 7.
Solved!
Go to Solution.

Scripting in Internet Explorer might be disabled by an Antivirus software. What Antivirus software is installed on your computer?
Meanwhile you can try the “legacylogin” workaround, which should enable login to Skype using the old legacy login window. However, you will not be able to login using Microsoft account (email address).
Quit Skype. Make sure that you don’t see any Skype.exe processes in Windows Task Manager. If necessary, then stop these processes.
Open this folder on your computer:
C:\Program Files (x86)\Skype\Phone\
You should see there the Skype application file (Skype.exe). Right click on the Skype.exe file and select: Send to – Desktop (create shortcut). Right click on the newly created shortcut and select Properties and then the Shortcut tab. In the Target field you will see now:
"C:\Program Files (x86)\Skype\Phone\Skype.exe"
Click with your mouse on the text in the Target field and move your curser one space after the last quotation sign and add the text /legacylogin. The text in the Target field should now read:
"C:\Program Files (x86)\Skype\Phone\Skype.exe" /legacylogin
Click OK to save the changes. Start Skype using this new shortcut. Can you now login to Skype?

Blue screen with kernal_data_inpage_error

I have Yoga 2 13 and it has been quite slow for a long while. Now in the mids of my work, blue screen appeared showing: '"default boot device missing or boot failed"'.Afterwards another blue screen with kernal_data_inpage_error appeared. I managed to run the PC again, but it hangs and the blue screen appears unexpectedly, I have runned RAM and windows diagnosis and they showed all fine

T
his Stop message indicates that the requested page of kernel data from the paging file could not be read into memory. This Stop message is usually caused by a bad block (sector) in a paging file, a virus, a disk controller error, or failing RAM. In rare cases, it is caused when nonpaged pool resources run out.
Try running check disk to start with and see whhat happens and of cause a virus scan

Satellite L300-1DN - Blue Screen and STOP 0x00008086

Dear Toshiba users
I use Vista Service Pack 2 ,32-bit on Satelite L300-1DN. My laptop does not boot.
I get a blue screen with a message at the end STOP: 0x00008086
I tried F8 and Safe Mode and also F8 and Repair, but after starting downloading files is either getting stuck at "crcdisk.sys" or after getting the green flashing bar of Microsoft Co I get a black screen with a large white pointer and then again crashes and gives the same blue screen.
Any help will be greatly appreciated.
Best regards
Agelos

Found the other thread which you have created some time ago:
http://forums.computers.toshiba-europe.com/forums/message.jspa?messageID=251690
Seems that you had some problems with OS in the past
Did you try to recover the notebook using Toshiba disk?
Possibly it was hardware related issue
Check the HDD and RAM.
HDD can be checked using free software called Drive Fitness Test.
The RAM modules could be removed separately and you could try to run the notebook using one module only in each slot
Maybe this helps otherwise new modules should be used
Of course it could be possible that RAM is ok and the issue is related to serious motherboard fault

Blue Screen and STOP: 0x00008086

Dear Toshiba users
I use Vista Service Pack 2 ,32-bit on Satelite L300-1DN. My laptop does not boot.
I get a blue screen with a message at the end STOP: 0x00008086
I tried F8 and Safe Mode and also F8 and Repair, but after starting downloading files is either getting stuck at "crcdisk.sys" or after getting the green flashing bar of Microsoft Co I get a black screen with a large white pointer and then again crashes and gives the same blue screen.
Any help will be greatly appreciated.
Best regards
Agelos
Solved!
Go to Solution.

Satellite L300-1DN (PSLB8E-05V007EN)
..also F8 and Repair, but after starting downloading files..
I don't understand, Agelos. Can you reach the Windows Recovery Environment? It looks something like this.
-Jerry

My macbook pro freezes and then displays a blue screen with black stripes... do you know what's wrong with it?

My macbook pro freezes and then displays a blue screen with black stripes... do you know what's wrong with it?
I have a two and half year mac book pro... I've had some issues with the screen looking scrambled when I quit certain applications, but now it's turned into something worse. I'll be working on my computer and the thing will freeze. When I force restart, the first screen, the apple logo, will be a blue tint and won't boot up normally. Then I try safe mood and it will then boot just fine. But there are blue stripes on my screen. The screen alternates from a blue tint to normal and if the computer freezes again the screen will become completely blue with black stripes. I haven't tried reinstalling my software because I don't have the startup discs that came with my computer. If I was sure that would fix it I would purchase them, but if it's a hardware issue I'm afraid that I'm screwed. I've been able to successfully get the blue off my screen by putting it to sleep and then waking it up, but that's not working well anymore either.
Does anyone else have experience with this? Is it the firmware or what? I have a MacBook Pro from early 2011 and I'm running Mac OS X 10.6.8.
Please help... Thanks!

I just experienced this exact same issue with my early 2011 15" macbook pro. Since like a month after purchasing it I had issues with the screen randomly going dark on me. I sent it in for repair inder waranty they replaced the gpu and logic board but I continued to have the same issues with the screen randomly going black sometimes I would need to reboot it in order to get the screen to go back on but it happened so infrequently and I used the computer for school so disnt find the time to resend it in to apple. Just last night the screen started to display the blue screen with black verticle lines on it. I called apple and explained to them the issues that had been ongoing since I purchased the laptop but they said because I was now outside of warantee that any repairs at thia point wouldn't be covered. Fml so glad I spent 2200 on this future proof macbook pro what a joke my sister purchased a toshiba laptop for 300 4 years ago and it still running like a champ. I loved my macbook but at the price I paid I expect it to last longer than 2 years before leaving me high and dry. *** apple??

When trying to save page in Yahoo! Bookmarks, I receive blue screen with message:A problem occured while trying to save bookmark. Please try again later. I get the same message every time.

When I click on Yahoo Bookmark Icon & click on Save this page,
I get the normal screen Save To My Bookmarks, etc. I fill out as
normally & click save. That is when I receive blue screen with above message. Frustrating because it lets me go through the process but then will not save. Is this a cookie or privacy issue??

At the top of yahoo bookmarks there is a message:
To Yahoo! Bookmarks users:
Yahoo! Bookmarks is transitioning and will be exclusively available via Yahoo! Toolbar. During this transition, you will be able to access your bookmarks in read-only mode.We expect the transition to be fully complete by October 20, 2011, after which you will have access to your bookmarks with the ability to add/ edit/ delete bookmarks.
Please download Yahoo! Toolbar for a full bookmarks service. We sincerely apologize for any inconvenience during this period.
But the toolbar dosn't work either, even after it is updated, so we may just have to wait.
Hope this helps :)

I tried to soft reset my ipod touch with the top button and the screen button. it turned off and went to the blue screen with the apple. now it won't do anything-it has stayed on that scren for 4 hours now. does anyone know how i can fix this?

i tried to soft reset my ipod touch with the top button and the screen button. it turned off and then went to the blue screen with the apple like it should. however, it now just stays on that screen. it has a sort of clock looking thing at the bottom of the apple that does not move either. it has stayed on this screen for over 4 hours. i also can not hard reset it in itunes. i am not really goood at this sort of thing. does anyone have this problem or a possible solution? thanks

See Here for
Frozen or unresponsive iPod touch
The Basic Troubleshooting Steps are:
Restart.. Reset.. Restore...
Try this First... You will Not Lose Any Data...
Turn the iPod Off... ( if it isn’t already )
Press and Hold the Sleep/Wake Button and the Home Button at the Same Time...
Wait for the Apple logo to Appear and then Disappear...
Usually takes about 15 - 20 Seconds... (But can take Longer...)
Release the Buttons...
Turn the iPod On...
If that does not help... See Here:
Backing up, Updating and Restoring
http://support.apple.com/kb/HT1414

Recovery Problem - Blue Screen error (STOP: 0x00008086)

I am working on a Toshiba Satellite laptop and need to recover back to original state. I do not have Recovery Disks, however, I have followed the Toshiba 'How to' instructions (F8 then select Repair your Computer) it show the Windows progress bar then goes to a black screen for a while then I get a Blue Screen error (STOP: 0x00008086).
Is there any way to get around this?

Hi
If the HDD recovery does not work then you need the recovery disk.
Here you can order this.
https://backupmedia.toshiba.eu/landing.aspx
Greets

My macbook13in has a blue screen with error code 10813

my macbook 13in has a blue screen with error code 10813

Reinstalling OS X Without Erasing the Drive
Boot to the Recovery HD: Restart the computer and after the chime press and hold down the COMMAND and R keys until the menu screen appears. Alternatively, restart the computer and after the chime press and hold down the OPTION key until the boot manager screen appears. Select the Recovery HD and click on the downward pointing arrow button.
Repair the Hard Drive and Permissions: Upon startup select Disk Utility from the main menu. Repair the Hard Drive and Permissions as follows.
When the recovery menu appears select Disk Utility. After DU loads select your hard drive entry (mfgr.'s ID and drive size) from the the left side list. In the DU status area you will see an entry for the S.M.A.R.T. status of the hard drive. If it does not say "Verified" then the hard drive is failing or failed. (SMART status is not reported on external Firewire or USB drives.) If the drive is "Verified" then select your OS X volume from the list on the left (sub-entry below the drive entry,) click on the First Aid tab, then click on the Repair Disk button. If DU reports any errors that have been fixed, then re-run Repair Disk until no errors are reported. If no errors are reported click on the Repair Permissions button. Wait until the operation completes, then quit DU and return to the main menu.
Reinstall OS X: Select Reinstall OS X and click on the Continue button.
Note: You will need an active Internet connection. I suggest using Ethernet if possible because it is three times faster than wireless.
Also see:
Reinstall OS X Without Erasing the Drive
OS X Yosemite- Reinstall OS X
OS X Mavericks- Reinstall OS X
OS X Mountain Lion- Reinstall OS X
OS X Lion- Reinstall Mac OS X
Note: You will need an active Internet connection. I suggest using Ethernet
if possible because it is three times faster than wireless.

Satellite A350 - Blue screen with error message

When starting windows7, I am getting blue screen with error message 0x0000116.
Can anyone assist please?

It looks like a graphic card driver is a trouble maker.Try to reinstall a graphic card driver in safe mode (f8 on startup). Read this article for information:
http://social.answers.microsoft.com/Forums/en-US/vistahardware/thread/eb584685-6b8b-4ad7-b6cc-ae5ee78095fb
It's for VISTA but should be the same for win 7 too.

Blue screen with error message

Product Name: HP Media Center M7250n Desktop PC
Product #ED842aa-aba
I have been getting a blue screen with error messages that ask if this is the first time i get the error and then at the end it says it is dumping memory. I would like to wipe my harddrive and reinstall XP but my system is out of warrenty and HP won't provide me a recovery CD. What are my options.
This question was solved.
View Solution.

Hi,
You are most welcome.
"I work for HP."
Please click the "White Kudos" star to say thanks for helping.
Please mark "Accept As Solution" if my help has solved your problem.

Blue screen with *** STOP: 0x000000A5 (0x0001000A, 0x00000000, 0x00000000, 0x00000000)

Similar Messages

Maybe you are looking for