Blue & White LCD display

Hey everyone, I was going through my old apple items and found an about 14" LCD display, with the outside plastic the same blue and white as the popular G3. It is mounted on a spring loaded base which is height adjustable and can pivot up/down/left/right. There is also the option to remove the fancy base and use a kick stand to hold it up. It has buttons under the front edge, and even the option for RCA input!
I was hoping someone could help me find more info on this, and maybe even how much it maybe worth. Thanks!

Hi an, I have one, are you sure it's not a 15"?
http://www.everymac.com/monitors/apple/studiocinema/specs/apple_studio_displayblue.html

Similar Messages

  • Old Blue & White Studio Display

    Hope this is the right forum for this one.
    I have one of the Blue and White Studio LCD displays (Model 4551) which goes with my trusty B&W G3. I am about to get the backlights replaced as they are a little tired now and I was thinking that it might be possible to replace the actual LCD panel with a more modern one that has better contrast and viewing angles than the old one. Just wondered if any one has tried this or indeed found a suitable replacement panel at all.
    Not cost effective I know but I would like any info anyway.
    Powermac G3   Mac OS X (10.4.8)  

    The answers are in this article:
    86504- Power Mac G5: Display Compatibility
    If that does not answer your question, post back with more specific questions.

  • White screen after replacing LCD display myself. Help needed!

    I tried replacing the cracked LCD display, the fuctions on the iPod is still working but after replacing the LCD display it turns out to be white. I search the internet for solution but can't find any instead the possible problem. I found forums stating it could be the 'GPU chip' is fried on the logic board. I tried the cracked LCD on another iPod Touch 2nd Gen and found out that you could still see the outline of the lockscreen and time but when I tried on the original iPod Touch 2nd Gen it's just white, the same goes for the new LCD display. It's there any possible way to replace just that part without resetting the iPod Touch to its factory settings and how much would it cost?

    There
    http://www.ebay.ca/itm/360904670472?ssPageName=STRK:MEWNX:IT&_trksid=p3984.m1497.l2649
    the funny thing is i just replace de cable ....
    Thanks

  • LED display has blue cast compared to 23" LCD display

    Just purchased the 27" LED Cinema display. It is side by side with my 23" LCD display. The colors are dramatically different. Is there some way to calibrate the new 27" monitor so that it has the same appearance as the 23" LCD or is the technology so different that they will never really look similar? I have a Mac Pro 2 X 2.4 GHz Quad-Core Intel Xeon.
    thanks
    russ

    Yes, they do frequently have blue tints which cannot be calibrated out. I had to return two of them because of the problem and eventually just got my money refunded. I was told that Apple Engineering had no fix other than to suggest using a professional calibrator system which would almost certainly have done no good. I'd suggest you return the Thunderbolt display for refund and buy a different brand  or wait until Apple releases a new generation of displays, whenever that happens.
    Regards.

  • Faint White spots on LCD Display

    Hi,
    I have a few faint white spots on the LCD display of my Macbook Pro. I had similar problems with a previous Powerbook G4. The white spots are about the size of a Canadian nickel and are right in the middle of the display. Since they are in the middle of the display, they are quite annoying. I already tried cleaning the screen many, many times.
    I tried to call Applecare but they wouldn't even listen what I had to say since I was outside the 90 day phone support. I was under the impression that the Macbook Pro had a warranty of 1 year; but if they won't listen to what I have to say, how can I get them to do any warranty service on my laptop?
    Any suggestions or comments would be greatly appreciated. Thanks.

    Hey everyone,
    I've also experienced these same "white spots" on my Mac Book Pro. I purchased it about a year ago and they started appearing on my screen in October. It looks like someone used their finger tip and applied direct pressure on my display. They almost form a perfect circle pattern in the middle.
    I took my computer to an Apple store in Toronto and they couldn't diagnose what the issue was so they did the screen replacement under warranty.
    Unfortunately, it began happening AGAIN a few weeks ago and I took it back to a store today to have a "genius" look at it. Immediately, they said that it was a result of putting too much pressure on my screen. I wondered how the heck I could have accomplished this since I thought I treated my MBP like a baby. I was using a Crumpler laptop bag to tote my baby around and according to them a combination of; all the gear I was carrying (which isn't much), the fact that it was a shoulder bag (resting on my hip when I walk), and the fact that I use one of those Marware keyboard covers together (which applies pressure from within) contributed to the pressure put on the center of my screen. And ultimately, they won't replace the screen because it's "my fault".
    I'm just bugged by it because...
    1) The genius I originally dealt with didn't know what the problem was so I couldn't take any measures to better protect my computer after it was repaired. I could have bought a tougher case, made sure I was more aware of what else I put in my laptop bag (although I never put that much in it initially), or just left it at home.
    2) The genius (who was quite rude actually and treated me like I was stealing from him) I dealt with the second time said he saw this issue quite often but there is no warning anywhere saying that the Mac Book Pro can be succeptible to this. Geez, I have friends/family with Mac laptops that treat them like crap and have no issues like this. Also, I know people with PC laptops that are built like tanks (who spent a fraction of the money I did) and can put up with alot of day to day punishment.
    3) I bought the Marware keyboard cover AT the Apple store. Why are they selling something that has the ability to damage their laptop screens?
    So I hope people can read this and take the proper precautions when storing their Mac Book Pros during transport. Luckily, the spots aren't too bad, I just make sure my desktop wallpaper is dark so the spots won't be so obvious.
    Sorry Apple, you just lost a point with me.
    Mac Book Pro 1.83   Mac OS X (10.4.8)  
    Mac Book Pro 1.83   Mac OS X (10.4.8)  

  • Power G3/LCD Display Upgrade?

    I have a Blue and White Power G3 and would like to upgrade to a 22” LCD display.
    Are there any limitations with OS 9.2.2 and the ATI Rage 128 card that I should be aware of when making a selection?
    I don’t want to spend any more than I need to and so I don’t want the display to exceed the limitations of my computer?
    What features could be left out?
    For example, would it be better to get a display that just has only a VGA (analogue) input instead of a combination of VGA and DVI,(digital) inputs, and perhaps with less resolution, etc.?
    Someone told me that it’s not a good idea to use a display that’s over nineteen inches wide.
    Do you have any recommendations?

    I just bought a AJ2216WBD Acer 22” monitor with a 1680 x 1050 resolution and I’m afraid to take it out of the box because of what I learned about lcd screens and native resolution. I read the following about lcd screens:
    “The most noticeable disadvantage is their fixed or native resolution. An LCD screen can only display the number of pixels in its matrix and no more or less. It can display a lower resolution in one or two ways. Using only a fraction of the pixels on the display or through extrapolation. Extrapolation is a method whereby the monitor blends multiple pixels together to simulate a single smaller pixel. This can often lead to a blurry or fuzzy image particularly with text when running the screen below its native resolution.”
    And unlike a CRT screen where the resolution can be scaled down.”
    The highest resolution my 128 rage card offers is 1600 x 1200 at thousands of colors and 1280 x 1024 at millions of colors. And so I’m wondering if I’m better off with a view screen that has a lower native resolution, such as the Samsung Syncmaster 940T or 904bx 19” and the LG LI953TX 19” with a resolution of 1280 x 1024
    Although, I’d actually prefer a 22” screen.
    There is also the Viewsonic VA1926W with a resolution of 1440 X 900 but that would be pushing it because I would never be able to have native resolution with millions of colors.
    What would be the most normal situation for an lcd screen with a Blue and White Power G3 450 MHz computer,, in terms of resolution and screen size?
    Also, according to Apple, the highest 2D display mode is 1280 x 1024 at 75Hz with millions of colors, thousands of colors and 256 colors. While the maximum 3D resolution is 1280 x 1024 with millions of colors and 1600 x 1200 with thousands of colors.
    How can the resolution be higher in 3D than in 2D mode for thousands of colors?
    Do you just get more with 3D?
    I would like to fully experience the capabilities of my rage card with the best lcd screen to bring it out.

  • Creative MP3 Player (Microphoto) Blank LCD Display Scr

    [size="">Hi, The LCD Display Screen on the Creative MP3 Player is blank. The blue background light will come on but nothing on the screen. I saw that it was suggested to update the firmware, however, I have no idea how to do that. If someone can explain to me how to do that I will try it. Or maybe you can suggest something else that I can do. I already tried several things suggested on your website, like removing the battery and installing it again, etc. I would appreciate it if someone would help me. Thanks!

    [size="">Good Morning,[size="">I tried the firmware upgrade, however, the screen is still blank. Should I have removed the batter and re-install it again? I tried calling support, however if my product is not in warranty it really doesn't give me that many options or refers me to anyone. Is there a telephone number in particular I should call. Thank you for your advise though, I appreciate it!? Have a

  • About monitors and LCD displays

    I want give you some directrices about the display sub system.
    Like you all know there are CRT monitors and LCD displays.
    CRT
    CRT monitors are based upon electron beams hitting Electroluminescent phosphorus. In these monitors the most important parameters are:
    1) Dot pitch
    2) Refresh rate
    Dot pitch is the size of a single phosphorus point, smaller is better. Typical values range between 0.24 and 0.25. Beware with monitors having a not constant dot pitch, there are monitors with dot pitch of 0.24 at center of screen and 0.25 at the borders. I recommend monitors with constant dot pitch size across all screen.
    Refresh rate is the number of times a single electron beam travels across the screen drawing a single frame (from left to right and top to bottom) each second. It is measured in Herz (Hz). Bigger is better. Typical values range between 60 Hz and 120 Hz and the value depends upon resolution, more resolution goes to less possible refresh rate. If you are going to play games with shutter glasses, make sure your monitor is capable of 120 Hz minimun at the playing resolution. In 3D Stereo, each full 3D frame must be drawn 60 times/second (60 Hz) but a 3D frame is a single right eye frame and a single left eye frame, 60 Hz for left frame and 60 Hz for right frame are the full 120 Hz. If you CRT is not capable of these 120 Hz your eyes will suffer fatigue / strain and you would have a great headache after prolonged time periods.
    LCD
    A LCD display do not uses a electron beam to excite phosphorus and generate colored points, instead this it uses a grille and a special lamp. Instead drawing a frame line at line from top to bottom and left to right, it renders the frame in a step only and continuously, these displays are flat for this, there is no necesity for high voltage and magnetic fileds to move the electron beam. In these displays these are the more important parameters:
    1) Dot pitch
    2) Response time
    3) Number of colors (color space)
    Dot pitch is the same as with CRTs
    Reponse time is the time it gets going from pure white to pure black. Less is better. It is measured in miliseconds. Good typical values range about 16 ms. If you are going to use the LCD to play games, response time is the more important parameter at all.
    Number of colors are the simultaneus colors in screen. It have a inverse relationship with response time. It is measured in million of colors or bits. 24 bits of color depth are 16.7 million of colors. Typical values range agout 16 / 16.7 millions. Greater is better. LCDs with 16 ms response time have, usually, 16.5 millions of colors.
    Somethimes, the manufacturer will provide you drivers (setup or inf files) for your operating system. I recomend install this drivers. Don't panic if there are no drivers for your display device, Windows, probably, will find the suitable driver for your brand and model.
    If you have a CRT and you are stuck at 60~85 Hz you will need the right driver because Windows would not have found a suitable driver from its drivers base and it chose a standard monitor driver.
    If you have a LCD and you are stuck at 60 Hz, all is fine, as i have told you yet, LCD displays paint the screen continuously, you will not appreciate any flicker at 60 Hz in these devices. You can check this if you have a digital camera, make a photo of a CRT with a shutter of <monitor refresh rate> * 1.5. You will see a partially drawn picture. If you take a photo of a LCD with the same shutter rules you will get a full picture. With LCD you will get full pictures always, independently of the shutter.
    I hope al this info will be helpful to you.

    I have found a very interesting link on the Anandtech Web site about LCDs, it is a old one but i think it will be useful.
    The link is this

  • Studio Monitor (Graphite/Clear) to Macintosh G3 (blue/white) connection

    I have a Apple 17inch Studio Monitor (Graphite/Clear) that I'm connecting to a Macintosh G3 (blue/white) what kind of adapter do I need? The monitor cable has a male end with 3 rows by 10 pins plus a flat pin on the side. The G3 port is a 3 row by 5 pin female socket.

    Welcome to the Apple Forums, recently revised just for your visit!
    Does your Studio Display have its own AC power cord? If not, what it really needs is a display card from a G4 or an alternate power supply. I think Dr. Boot sells one, but it runs about US$100.
    There is a lot of word-salad surrounding the various interfaces, and what can work with what. I suggest this article, which may help make more sense of it:
    58692 -- Power Mac G4: Display Compatibility.
    The Blue & White G3 is like the G4 PCI graphics.

  • LCD display for graphic designer/photographer

    My Mac Pro two 2.26 GHz Quad Core should arrive in a couple of days. I'm now in the process of choosing a 22"-24" LCD display monitor. As I am not attracted to the Apple 24" display's glossy surface, I've narrowed display choices down to these:
    1) EIZO CG222W 22.2" Widescreen LCD
    2) NEC MultiSync 2490WUXi 24.1" Widescreen LCD
    Anyone using or know anything about either of these? I understand they are popular with graphic artists and photographers, but I am particularly interested in learning of any compatibility issues with the early 2009 Mac Pro/OS 10.5.6. NEC's support website notes possible compatibility issue between its 2490WUXi SpectraView II calibration software and OS 10.5.6.
    If I chose the NEC model, could I use another calibration software/colorimeter with it instead? If not, then I would just go with the EIZO.

    just got my two 26" NEC MultiSync LCD2690WUXi2 and hooked them up to a new nehalem mac pro with a radeon 4870. the monitors work perfectly. all i can say is wow. the color accuracy out of the box is great. the brightness uniformity is incredible. the blacks are really black and the whites are perfectly white. i've owned two 23" apple cinema displays and two 24" led cinema displays in the past, and these NECs look much better. very professional.
    i do have two gripes with the 26" NEC MultiSync LCD2690WUXi2. its cased in some sort of plastic. the base is made from the same material. i'd rather have an aluminum casing and base like apple provides. the other grip is that there is a lot of flex where the actual panel attaches to the base. its a bit wobbly. this i don't like at all. they could have done something better with this. otherwise no other problems to report.
    but all in all, the image on the screen is so good, that i won't complain anymore from this day forward. an absolutely stunning image on these screens. love em'!!

  • LCD display in reverse video, B&W, can't seem to reset

    The LCD display on our PowerBook G4 kicks into reverse video, black & white, after a normal boot where we see regular colors, including the desktop for a moment. We have walked through all the possible display settings and can't find anyplace where we could accidentally put our settings to reverse video.
    The fact that we can see normal colors until the end of the boot would indicate that nothing is physically wrong with our LCD panel.

    Hi, Gaydpdx. Press the following key combination: Command-Option-Control-8.
    Someone has inadvertently typed that key combination on your computer, invoking one of the display settings for visually-impaired users that are found in the Seeing tab of the Universal Access pane of System Preferences.

  • Blue & White G3 upgrade to G4?

    Hello - I have an old G3 Blue/white which I would like to use to run a slideshow in my gallery. How do I upgrade this machine to achieve this? I don't need to use the machine for anything beyond running a slideshow through an LCD projector. Thanks.

    What are the requirements of the slide show app? What are the specs on your G3 B&W?
    If your G3 is near stock, it's probably worth less than $50. So it's not cost effective to spend many $ on an upgrade.
     Cheers, Tom

  • MACBOOK DON'T CONNECT WITH LG FLATRON LCD DISPLAY

    Hi friends!
    I bought a LG FLATRON LCD DISPLAY Model M1994A.
    My Macbook 13" have a 10.5.6 Leopard.
    The fact is when connect de Macbook with LCD screen thru VGA cable and miniDVI adapter. Plug the miniDVI adapter, and the screen of Macbook blinking forever at the blue screen; the lcd has the message "NO SIGNAL"
    If I unplug the miniDVI adapter, everything gets back to normal on the macbook screen. I plug it again, I get the blinking blue screen.
    Tried rebooting, unplugging everything else from the external screen, no luck.
    If I boot the macbook with the external screen on and the macbook closed, then it is recognized a little bit: appears the apple boot screen then blinking, but when I want to use both screens, it will blink again.
    HELP ME PLEASE!!!
    Regards from Chile!

    May not be any help but, I have the LG W1952TQ and it works great with my MacBook. You may try going to system prefs, click on displays, then click on Detect Displays and see if that works, I had to play with the resolutions some and ended up selecting 1152 X 864 setting for mine.
    Hope this helps ya,
    Barry

  • Color management on LCD displays, need help

    Dear all,
    I know the same topic has been already raised so many times, but i just can't help to ask it again. I am sorry for that, I just realize I will at least get a concept of what to do next. Ppl here are helpful.
    I don't own any Apple monitor. I have a Macmini, connected to a new SONY LCD display, SDM-HS95P, by DVI connector.
    As everyone knows the situation of LCD monitors. They have higher contrast, brigther image that traditional CRT monitors. That's why photographers and graphic designers are blaming all the time.
    And now, I face the same as they do. My monitor is no more "WYSIWYG". The red i have here, may become another red on printing. The yellow I have here, may become orange on CRT.
    I calibrated with the Colorsync of OSX, I decreased the contrast and bright level of my monitor, but they dont help much.
    Someone suggested here to purchase color management hardwares. Of coz i know they are helpful. But the point is, how can a little student to afford a such expensive hardware for only doing color management?
    Apple displays are all in LCD these days, how does Apple help their users to overcome the mentioned situation?
    I know this maybe just a never-ending question, but i think ppl here may come up with some new ideas in resolving this.
    Please kindly help, much appreciate! Thanks!
    regards,
    KKCHUNG
    Macmini 1.25 GHZ/ 1GB ram   Mac OS X (10.4.3)  

    Hi.
    Apple cinema displays do not offer the user the ability to adjust the contrast. You need to be able to adjust contrast when calibrating the 2nd monitor to match the target white and black luminence values of the first monitor.
    Contrast is needed in order to adjust the white luminence value of the monitor you are calibrating. You need to be able to adjust the black and white luminence values of monitor 2 when using the white and black luminence target values from monitor 1 if you want both monitors to be calibrated so that they use the same (same but seperate) profiles.
    Colorvision (makers of spyder2 pro) has indicated that this is a huge issue with the ACD monitors and they are currently researching a workaround.
    If anyone knows how to fix this... please tell me (us)... thanks.

  • Photosmart c6380 lcd display not lighting up

    I have a C6380 all in one printer and the lcd display back light has been intermittently going off and on. The display still works and you can read everything on it, but it is just hard to read when the display is not being backlit. Sometimes when I tap on the screen or flip the display up and down the light will turn back on, but only for awhile. I have tried searching for other posts about this type of problem, all to no avail. I have even gone as far as trying to find a replacement part for it, nope. I just don't want to replace the printer because it is only about a year old and works great. Any help would be greatly appreciated.
    Thanks.

    If the printer is less then year old, then I suggest you call HP and get the printer replaced. If you exceed the 1 yr. warranty, then the printer replacement will not be free of charge.
    Make it easier for other people to find solutions, by marking my answer with \'Accept as Solution\' if it solves your problem.
    Click on the BLUE KUDOS button on the left to say "Thanks"
    I am an ex-HP Employee.

Maybe you are looking for