BO4 - moving servers behind scenes and any impact on cms metadata
Hi,
We have a couple of environments
One has physical server and cms metadata reflects name of this server.
The hardware team want to create a virtual server of same name and move the content from this physical server to the new virtual server.
Providing the new virtual server has the same name as the physical server, will this be ok?
Also another environment with exsiting virtal server - they plan to move thsi to another virtual serevr again of the same name.
Will this be O.K.
Understand would be problems if the server names were going to be different as the server names hled in the cms metadata but given that will be same names anyone see any potentail problems with this approach.
Thanks
Hi Philip,
Recently one of test Physical server has moved to Virtual Server. Didnt face any major issue.
Make sure that you have connectivity with the Reports DB sources,Win AD/Ldap Ports are opened for all the required services.
Note: we have maintained the same host name and same IP. CMS DB and Audit are in the same Server.
Similar Messages
-
Is there a limit on number of object links to DIR, and any impacts of this
Hello All,
Can you please let us know if there is any limit on the No of Object links to be maintained in the Object Link tab of DIR,
Our major Concern comes as there is One DIR logo / symbol, which is maintained in most of the Material Master around 1000s
and also the same DIR is used in all the Service and maintenance Notification as an Attachment, so the list of Object link in DIR Object link tab is going beyond control above 10000s,
i wanted to know if there is any limit on no of Object links to be maintained in DIR object links, and is there any impact on DMS functionality if the list is ever increasing,
( also can i know if there is any workaround that the DIR is only displayed going in to Material master or Notifications but the same is not listed in the DIR object links tab as here it is going on increasing,)
Thanks and kind regards
Kumar SHello Christoph and Every one,
Thanks for the responses given, and providing a hint not to have many Object links, as it could be an performance issue going to the DMS DIR Object link TAB,
But in this particular case we are not assigning the Objectlinks going by the DMS Object links TAB, but it is done in other way round, going by the Equipment or Notification Screens,
There are few Health and safety document ( Which is created as a DIR in DMS) which needs to be assigned in Most of the Equipment and the new notifications created, and this document DIR is assigned from the Equipment and notification Screen,
And we may not be interested to go to the DIR to browse and Assign the Object Links, so as we do not frequently go and check the DIR or Use DIR Object link TAB for Object Link assignment will it in any ways cause performance Issue here??
And also as asked earlier can we have a one way attachment like the DIR is Visible in the Equipment or Notification Screen, but the DIR is not adding up the Equipment or Notification details in its Object links TAB, (by development or it is totally illogical to ask for)
Thanks and Kind regards
S Kumar -
PAT with a single public IP and several servers behind firewall
Hi,
New to the ASA 5505 8.4 software version, but here is what I'm trying to do:
Single static public IP: 16.2.3.4
Need to PAT several ports to three separate servers behind firewall
One server houses email, pptp server, ftp server and web services: 10.1.20.91
One server houses drac management (port 445): 10.1.20.92
One server is the IP phone server using a range of ports: 10.1.20.156
Basically, need to PAT the ports associated with each server to the respective servers behind the ASA 5505.
Here is what I have. Is anything missing from this config? Do I need to include a global policy for PPTP and SMTP?
ASA Version 8.4(4)1
hostname kaa-pix
names
interface Ethernet0/0
switchport access vlan 2
interface Ethernet0/1
interface Ethernet0/2
interface Ethernet0/3
interface Ethernet0/4
interface Ethernet0/5
interface Ethernet0/6
interface Ethernet0/7
interface Vlan1
nameif inside
security-level 100
ip address 10.1.20.1 255.255.255.0
interface Vlan2
nameif outside
security-level 0
ip address 16.2.3.4 255.255.255.0
ftp mode passive
object network obj_any
subnet 0.0.0.0 0.0.0.0
object network server_smtp
host 10.1.20.91
object service Port_25
service tcp source eq smtp
object service Port_3389
service tcp source eq 3389
object service Port_1723
service tcp source eq pptp
object service Port_21
service tcp source eq ftp
object service Port_443
service tcp source eq https
object service Port_444
service tcp source eq 444
object network drac
host 10.1.20.92
object service Port_445
service tcp source eq 445
access-list acl-out extended permit icmp any any echo-reply
access-list acl-out extended permit icmp any any
access-list acl-out extended permit tcp any interface outside eq pptp
access-list acl-out extended permit tcp any object server_smtp eq smtp
access-list acl-out extended permit tcp any object server_smtp eq pptp
access-list acl-out extended permit tcp any object server_smtp eq 3389
access-list acl-out extended permit tcp any object server_smtp eq ftp
access-list acl-out extended permit tcp any object server_smtp eq https
access-list acl-out extended permit tcp any object server_smtp eq 444
access-list acl-out extended permit tcp any object drac eq 445
pager lines 24
logging asdm informational
mtu inside 1500
mtu outside 1500
icmp unreachable rate-limit 1 burst-size 1
no asdm history enable
arp timeout 14400
nat (inside,outside) source static server_smtp interface service Port_25 Port_25
nat (inside,outside) source static server_smtp interface service Port_3389 Port_
3389
nat (inside,outside) source static server_smtp interface service Port_1723 Port_
1723
nat (inside,outside) source static server_smtp interface service Port_21 Port_21
nat (inside,outside) source static server_smtp interface service Port_443 Port_4
43
nat (inside,outside) source static server_smtp interface service Port_444 Port_4
44
nat (inside,outside) source static drac interface service Port_445 Port_445
object network obj_any
nat (inside,outside) dynamic interface
route outside 0.0.0.0 0.0.0.0 16.2.3.1 1
timeout xlate 3:00:00
timeout pat-xlate 0:00:30
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
timeout floating-conn 0:00:00
dynamic-access-policy-record DfltAccessPolicy
user-identity default-domain LOCAL
no snmp-server location
no snmp-server contact
snmp-server enable traps snmp authentication linkup linkdown coldstart warmstart
telnet timeout 5
ssh timeout 5
ssh key-exchange group dh-group1-sha1
console timeout 0
threat-detection basic-threat
threat-detection statistics access-list
no threat-detection statistics tcp-intercept
prompt hostname context
no call-home reporting anonymousThanks Lcambron...I got PPTP to work. Everything else works fine. I can access email, access my web server, FTP server, and PPTP server. However, from the above configuration, I cannot access my DRAC over the internet..The DRAC runs on a different internal server, and over port 445. So I have th following lines:
object network drac
host 10.1.20.92
object service Port_445
service tcp source eq 445
access-list acl-out extended permit tcp any object drac eq 445
nat (inside,outside) source static drac interface service Port_445 Port_445
Am I missing something here? Internally, i can telnet to port 445 on 10.1.20.92, so I know it is listening. However, externally, i cannot telnet to my external ip address of the ASA through port 445.
Thanks -
Is there any impact that apply Oracle CPU on standby and primary DB
We plan to apply Oracle April CPU on standby DB at this weekend. Then apply the same patch on primary DB next weekend. If I apply the patch on standby, then enable redo apply between primary and standby, is there any impact on primary DB. Theoretically, I don't think so. However, both DBs are production. I want to make sure there is no any impact by applying CPU in different time. Otherwise, I have to apply both DBs at the same time. Please advise. Thanks in advance.
853153 wrote:
I hope you read other people's post carefully. Don't pretend yourself is expert so that you can say whatever you want to say. This is the tech forum for Oracle technical people to ask question, seek help and so on. How do you know I didn't review document 278641.1 before I asked my question. Document 278641.1 only provide info on how to apply patch on primary and standby. Didn't say anything about applying the same patch on both DBs with data Guard at the different time. I just want to make sure If I apply patch on both DBs with one week difference, will this affect my primary database? Is there anything wrong here. If you paly in this forum as expert, please help people, not just look down people.
I suggest you review [url http://www.catb.org/~esr/faqs/smart-questions.html]How To Ask Questions The Smart Way.
When you ask for help, state the platform, operating system, Oracle version and patch level, no matter whether it seems important to the question or not. It most often is important. You may not know the difference between Itanium and PA-RISC, but that is important for Oracle and important for someone doing administrative work on an Oracle database to know. You should also learn to search the internet for answers to common questions. Everyone here wants to help, but few want to spoon-feed.
When you have any kind of standby, that constrains what you can do to a primary, if you want the standby to work properly. You need to understand how things get from one to the other, and how to decide when to simply rebuild the standby from scratch - and that decision is based on your configuration and requirements. You don't want to be in some undefined configuration for any period of time. -
I'm thinking of using Final Cut Pro to straighten slightly crooked footage and then re-import back to iMovie to complete the video. Does this have any impact on image quality?
As your rotate the image, you will begin to see black edges. So, as Tom implies, the image must be scaled up to hide those voids. If you shot 4k ad are editing in a HD timeline, no problem, lots of room to spare. If you shot 1080 and are editing in a 1080 timeline, you will run into issues at a certain point. However, if your 1080 project is going to be transcoded to 720 or ye olde DVD you won't notice any deterioration at all.
-
My 10 yr. old went behind me and downloaded some music which used all my money on my account. Is it any way that I can delete it and get my money back on my account.
You can try contacting iTunes support via this page and see if they will refund or credit you : http://www.apple.com/support/itunes/contact/ - click on Contact iTunes Store Support on the right-hand side of the page, then Purchases, Billing & Redemption
-
NAT and Servers behind CSS 11501
All,
Please forgive my asking this question again. I was injured shortly after asking the last time and out of work for a long period of time.
My problem stems from needing to allow my web servers to initiate traffic to the outside world from behind our CSS boxes.
The web servers sit behind a pair of CSS 11501 content switches in Active-Passive ASR with fate sharing. We are only interested at this time with load balancing HTTP and HTTPS.
Everything works inbound no problem.
What I need to do is setup some type of NAT for my 3 web servers to initiate HTTP/HTTPS for patches, send SMTP from the web apps, and initiate HTTPS for credit card validation.
I have setup NAT on PIX units and routers no problem, but I seem to be unable to do it on these boxes. :(
In reality something as simple as a PAT translation on the outside of the CSS boxes should be sufficient.
Is this possible with our setup? Does anyone have some code examples?
Thanks in advance.
Addresses changed to protect the innocent:
Load Balancer 1:
!*************************** GLOBAL ***************************
bridge spanning-tree disabled
sntp server 1.1.1.41 version 1
snmp community noway read-only
snmp community noway read-write
app session 1.1.1.252
app
logging subsystem netman level info-6
dns primary 2.2.2.41
dns secondary 2.2.2.42
ip route 0.0.0.0 0.0.0.0 1.1.1.1 1
!************************* INTERFACE *************************
interface e1
phy 100Mbits-FD
description "Connect to Primary DMZ 1 3550 Switch"
interface e2
bridge vlan 2
phy 100Mbits-FD
description "Connected to Primary LB Server Switch"
interface e8
description "Inter Switch Communication (ISC) Port"
isc-port-one
!************************** CIRCUIT **************************
circuit VLAN1
description "DMZ 1 Subnet (1.1.1.x/24)"
ip address 1.1.1.251 255.255.255.0
ip virtual-router 1 priority 254 preempt
ip redundant-interface 1 1.1.1.250
ip redundant-vip 1 1.1.1.161
ip redundant-vip 1 1.1.1.162
ip redundant-vip 1 1.1.1.70
ip redundant-vip 1 1.1.1.71
ip redundant-vip 1 1.1.1.72
ip critical-service 1 upstream_downstream
circuit VLAN2
description "Load Balanced Servers Subnet"
ip address 2.2.2.2 255.255.255.0
ip virtual-router 2 priority 254 preempt
ip redundant-interface 2 2.2.2.1
ip critical-service 2 upstream_downstream
Various Services, Owners and Content
Load Balancer 2:
!*************************** GLOBAL ***************************
bridge spanning-tree disabled
sntp server 1.1.1.41 version 1
snmp community noway read-only
snmp community noway read-write
app session 1.1.1.251
app
logging subsystem netman level info-6
dns primary 2.2.2.41
dns secondary 2.2.2.42
ip route 0.0.0.0 0.0.0.0 1.1.1.1 1
!************************* INTERFACE *************************
interface e1
phy 100Mbits-FD
description "Connect to Secondary DMZ 1 3550 Switch"
interface e2
bridge vlan 2
phy 100Mbits-FD
description "Connected to Secondary LB Server Switch"
interface e8
description "Inter Switch Communication (ISC) Port"
isc-port-one
!************************** CIRCUIT **************************
circuit VLAN1
description "DMZ 1 Subnet (1.1.1.x/24)"
ip address 1.1.1.252 255.255.255.0
ip virtual-router 1
ip redundant-interface 1 1.1.1.250
ip redundant-vip 1 1.1.1.161
ip redundant-vip 1 1.1.1.162
ip redundant-vip 1 1.1.1.70
ip redundant-vip 1 1.1.1.71
ip redundant-vip 1 1.1.1.72
ip critical-service 1 upstream_downstream
circuit VLAN2
description "Load Balanced Servers Subnet"
ip address 2.2.2.3 255.255.255.0
ip virtual-router 2
ip redundant-interface 2 2.2.2.1
ip critical-service 2 upstream_downstream
Various Services, Owners and Content.Gilles,
I added the following commands, and things seem to be working.
To circuit VLAN1
ip redundant-vip 1 1.1.1.80
!*************************** GROUP ***************************
group natout
vip address 1.1.1.80
add service nat_web_servers
active
service nat_web_servers
ip address 192.168.1.10 range 3
active
I do have a question about the above service commands.
I have 3 servers behind the CSS. Let's call them 192.168.1.10, 192.168.1.11 and 192.168.1.12. Am I correct in my thinking that adding range 3 then allows a match on all 3 of those servers and the CSS will then PAT these servers from the VIP address assigned to the group?
Otherwise, I think you have resolved this problem for us. Thank you. -
I am encountering crashes with Photoshop Elements 12. If I uninstall and then reinstall the software, will I jeopardize the 100s of photo images I have already moved into the Organizer? Any cautions for me?
If the app is designed correctly, the no, you won't. However, you'd have to ask the people who wrote the software, Adobe.
-
When I using the mouse to select portion of the diagram or the panel, or when I moving objects- I found that in all the vi's that I compiled from former versions of labview- there is a delay of close to a second to the actual selection or movement of the item. This happens in 2 machines out of 5 that I tested it, and it happened both in windows 2000 and in windows 98. any suggestions?
Sometimes a video driver issue. Update your video driver.
Or turn down the video driver hardware acceleration. Right-click an
empty area of the desktop, choose the Settings tab, choose the Advanced
button.
The location of this differs in different versions of Windows.
Win2000: go to Troubleshooting, and turn down the slider for hardware
acceleration.
Win98: I think it's on another tab.
Mark
ilan wrote:
>
> Delayed response of when moving objects in diagram and panel, happend
> in LV 6, only for vi's compiled from previous versions. any
> suggestions?
>
> When I using the mouse to select portion of the diagram or the panel,
> or when I moving objects- I found that in all the vi's that I compiled
> from former versions of labview- there is a delay
of close to a second
> to the actual selection or movement of the item. This happens in 2
> machines out of 5 that I tested it, and it happened both in windows
> 2000 and in windows 98. any suggestions? -
I moved all my photos and videos from iPhoto to external hard drive, then totaly formated my macbook and now trying to play videos of external hard drive, but they wont play and they in "quicktime containers" and really small in size (50 - 150 Kb). Please Help!!! My misuse will kill me if find out that we have no more videos from our honeymoon...
I moved all my photos and videos from iPhoto to external hard drive, then totaly formated my macbook and now trying to play videos of external hard drive, but they wont play and they in "quicktime containers" and really small in size (50 - 150 Kb). Please Help!!! My misuse will kill me if find out that we have no more videos from our honeymoon...
You may need to prepare yourself for a "World of Hurt" from your wife...
Since the average 0.9 megapixel JPEG photo file of normal graphic complexity stored at a high quality compression setting is 125-135 KBs in size, I would have to assume any QT video files you created of more than a fraction of a second in duration were most likely saved as "reference" files to only be 50-150 KBs. Basically, a reference file is q QT (MOV) file that tells a video player how to play data that is still stored in its original source file container(s). For instance, you could trim and merge a number of files together and save the result as a "reference" file that takes up very little room on your hard drive. Or, you could post fles to a server and create a "reference" file that is small enough to be sent as an email attachment that plays the uploaded data on someone else's computer as long as they are connected to the Internet. Unfortunately, for these reference files to work, all of the resources referenced within the file must continue to exist in their proper locations in order to be found and played by the reference. Since you did not indicate what "but they won't play" really means here or how you actually "moved" your iPhoto library files to the external drive, I can only make some "educated guesses" at this point. (BTW: for future reference, iPhoto has a built-in function that allows you to copy your library to one or more back-up locations and then connect to them by default when iPhoto opens or switch source libraries at will within the opened application.)
If you created reference files and saved them to an external drive, you should be getting an error message telling you the app needs to know where the source files are located so the reference file can re-connect to the resource data. If the original files were also saved, then simple navigate to the source files in oder to tell the app where they are now located. If the source files were deleted as part of the reformatting process, then you are up the proverbial creek whithout a paddle with little or no hope of doing anything about this issue. (I.e., reformatting and then re-installing a system drive usually means you would have little hope of recovering the specific "lost" data you want as there is always a good chance that some of the data segments were overwritten during the process.) -
I am upgrading my iPad to iOS 7 but the progress bar is at 1/4 position for two hours and not moving forward. Is there any problem with it? What should I do? Thanks.
This is a concern amoung many corporate users. It's going to take somekind of policy change with apple.
Enterprise support:
Call enterprise support (866) 752-7753 to create a case ID number -
Is there any impact on database if we change the time of server?
Hi,
Our DB server time is 45 minutes ahead of our application server. We have planned to reset the time of database server. Is there any impact on database if we change the timing of the server?
Platform: Solaris
DB version: 10.2.0.2.0
$ bash
bash-3.00$ date
Thu Apr 23 20:26:19 IST 2009
bash-3.00$ sqlplus /nolog
SQL*Plus: Release 10.2.0.2.0 - Production on Thu Apr 23 20:27:15 2009
Copyright (c) 1982, 2005, Oracle. All Rights Reserved.
SQL> conn /as sysdba
Connected.
SQL> select sysdate from dual;
SYSDATE
23-APR-09
SQL> select systimestamp from dual;
SYSTIMESTAMP
23-APR-09 08.27.53.250947 PM +05:30That's an application question, not an Oracle question.
Oracle doesn't care what time it is or when the time changes. Your application(s), however, may care. If you use SYSDATE to populate a row and rely on the date later to be unique or to indicate the actual order rows were inserted, changing the date on the server, particular moving it backwards, might cause problems for your application. Does your application have problems running during daylight savings time changes?
Justin -
Best practice for web servers behind a router (NAT, ACL, policy-map, VLAN)
Hi,
I'm a new Network admin, and I have some configuration questions about my installation (see attachment).
I have 3 web servers behind a router.
Public interface: 3 public ip adresses
Private interface: router on a stick config ( 3 sub-interfaces, 3 different networks, 3 VLAN)
I would to know the best way to redirect http traffic to the right server.
My idea is to map a public address to a private address, via NAT, but I'm not sure for the configuration. I could also redirect via Policy-map and filter by url content.
So if you have some advise for this case, it would be really appreciated.
Thank you.
Chris.Hello Christophe,
As I understand you want 1st that ;
if somebody go to A.local.com from internet then he will redirect to 192.168.1.10 in your internal network.
That means, you need static mapping between your public @ip address and your local ip address.
for this example, your local interface is Fa0/0.1 and I dont your public interface because it is not mention in your diagram. I will suppose S0/0 for public interface.
that is the config for the Web Server1. You can do the same with the remaining servers:
interface fa0/0.1
ip nat inside
interface serial0/0
ip nat outside
ip nat inside source static 192.168.1.10 172.1.2.3
static mapping from local to public.
I suppose you have done the dns mapping in your network and the ISP have done the same in his network.
ip route 171.1.2.3 interface serial0/0
or
ip route 0.0.0.0 0.0.0.0 interface serial0/0.
After these step for each web server, you will get the mapping.
Now you can restrict access to this ip only to http or https protocol on your isp and after on your local network
like
ip access-list extended ACL_WebServer1
permit ip any 192.168.1.10 eq www
deny ip any 192.168.1.10
exit
interface fa0/0.1
ip acess-group ACL_WebServer1 in
no shut
exit
That is the first step.
Second step : you want to filter traffic by url, that means layer 5 to 7 filtering.
I am not sure that it is possible using cisco router with (ZBF + Regex).
Check the first step and let us know !
Please rate and mark as correct if it is the case.
Regards, -
Does Change to DESADV (ZXTRKTOP,ZXTRKU0) userexit has any impact on SHPCON
Hi All,
I need your help on clearing my doubt.
I recently create a new extended DELVRY03 idoc (ZDELVRY03) with message type DESADV and added new segment under E1EDL24 with contains prodcution date field. Def. logice in user eixt EXIT_SAPLV56K_002 includes ZXTRKTOP& ZXTRKU0.
Does changes to this idoc with message type DESADV has any impact on SHPCON message type with idoc DELVRY03(basic idoc)?
Since after i moved to devp. to QAS SHPCON is haning with status 64 and is never getting process.
When i force it thru BD87 it gives this short dump message
Runtime errors DBIF_RSQL_INVALIDD_RSQL
EXCEPTN CX_SY_OPEN_SQL_DB
and it is pointing to the user exit EXIT_SAPLV55K_005. But i have not made any change to this user exit.
Can someone tell me if DESADV changes might has to be anything with SHPCON status 64?
IS there any way to resolve this.
Appreciate your help in advance.
Thank you.
Mamathahi mamata
can u please post the answer -
Installation of Microsoft Visual C++ 2005 C Runtime and its impact
Dear All,
I am working with a client, and as a prerequisite, Microsoft Visual C++ 2005 C Runtime has to be installed on the client's servers in order for one of our products to work.
Since at the moment the client do not have this installed on their servers, and the fact that their servers have not been rebooted in a long time, they feel that there is a risk in installing Microsoft Visual C++ 2005 C Runtime if rebooting the server
is required.
Could anyone provide me with some insight into the following:
1. If there is any impact on the OS (Windows 2003 R2) or the IIS (version 6.0) or any other MS products or applications by installing Microsoft Visual C++ 2005 C Runtime
2. If any common library will be written into during the installation and what is the impact
3. If the server has to be rebooted after the installation
4. What is an appropriate procedure for rollback (is it simply uninstalling “Microsoft Visual C++ 2005 C Runtime” and would a reboot of the server be required after the uninstall, etc.)
Would anyone be able to provide any insight on the above?
Many thanks in advance.1. Use reliable backup and preserve return path.
2. Do pilot test on computer that is not part of your enterprise.
3. Consider applications that may have different versions of MSC libraries. Here I can se the possible problem.
Regards
Milos
Maybe you are looking for
-
HOT HOT HOT HOT!!! Mac Book Pro Retina, Mid 2012 with 2 external Displays HOT HOT HOT HOT!!!
Hi, i think i have a serious heat problem and i am a bit afraid of melting the mac book (It happend before with an older mac book pro, graphic card melted...yes, it did...) i own a Retina, Mid 2012 Processor 2.6 GHz Intel Core i7 Memory 16 GB 1600
-
MCEKPO-MENGE issue through 2LIS_02_ITM for Statistical Purchase Order Items
Hello Everyone, I have come across this strange scenario where a given Purchase Order Item in the Source system - SAP R/3 has been changed in the following sequence, 1. First the PO Item was marked as a Deleted PO - LOEKZ = L which set the STAPO = X
-
How to identify different connections/clients from RMIServer???
Anyone knows how one can do to identify different connections or clients from the implementation/server-object in RMI?? Do I have to send a hostname from the client via method parameter?? If so, any recommendations on which unique name to use?? Would
-
I`m from Costa Rica and want to buy an iPad mini and Air, when I try to buy it online I have to choose Verizon, Mobile, etc. to add it to my cart, is this normal buying on line so I can use it unlocked in my country.
-
What is my iPads phone number?
How can I find out the phone number connected with my iPad?