Branch Office DC Demand Dial VPN connection keeps failing

here is me issue
Our Branch Office DC is connected to Main Office DC with a Demand Dial Connection in RRAS Everything is connected fine for a little bit then its like the connection just gives out, it stays connected but i cannot ping the branch office DC with the local
IP from the Main Office or access any network shares on it. When this happens i have to disconnect the server at the remote office and wait for it to reconnect im currently baffled as there are no Error LOGS to help me along and there doesnt seem to be anything
that would be causing the issue for now until i get some answers as to what is going on i opened a command prompt on the DC here at the main office and i typed "ping 10.141.70.25 -t100" to monitor the connection more or less and when i see it timeout
i reconnect it, i also have the networking tab open in task manager to monitor the LAN and RAS (Dial-In) Interface the LAN doesnt seem too active but the RAS Interface does its got a constant network utilization of 0.28% and the Demand Dial interface
on the remote office DC has a Utilization of 0.38% (Server Just disconnected as i was typing this and the utilization on the VPN connections on both servers went through the roof) heres the troubleshooting i have tried so far
1. Rebooted both office DC`s at the same time
2. Rebooted the branch office DC alone (this helped a little because the connection is staying active longer without fail)
3. looked through all RRAS configuration on both servers to see if theres any mistakes by any other administrators (None Were Found)
4. Used wireshark to see if there was anything interfering or that would cause this to happen (Nothing found)
5. manually connected to the server in multiple ways like accessing network shares and remote management via MMC and manually making the servers replicate to see if any of that was causing issues and it wasnt
My thoughts: im starting to think it may be a switch or something causing the connection issue at the branch office because the main office has all new routers and switches and just recently got a 100.00MBPS connection but nothing was affected for a good
month so im not thinking it is the new connection or anything at the main office if theres something im overlooking here please let me know if some ipconfig /all results are needed i can provide them
Viper Technologies Computer Repair Putting The Venomus Bite Back In Your Computer We Are Located In Antigonish ,NS Canada Check Us Out HTTP://WWW.VIPERTECHNOLOGIES.TK

Hi,
Are there any error messages on the event log ?
Meanwhile, it is more network issue, i think you may ask in network forums:
http://social.technet.microsoft.com/Forums/en-US/home?forum=winserverNIS
Regards.
Vivian Wang

Similar Messages

Hp office jet 6700 (Mac)-wireless connection keeps failing...

Hi-I am hoping that someone has a solution for this. We have an HP Officejet 6700 that has worked flawlessly till last week. The wireless signal keeps dropping. I think that is the issue because if I go into Setup on the printer itself and go to Network and start all over with finding my router, it works fine. For one print job. Then if I have something something else to print I have to go through that whole setup routine again.
If I just go to Print it says locating printer and then it says that the printer is not connected. What is going on?? Very frustrated. I tried uninstalling and reinstalling the driver (I downloaded the driver from the HP website). That didn't fix it. I saw that there was a firmware update but couldn't install it even though I plugged my laptop into the printer with a USB cord.
Something is going on that I don't have a clue in how to fix it. I really appreciate any help. Thank you, Judy

Hi mrstucci,
I would to help you establish a more consistent connection between your Officejet 6700 printer and your Mac. Please use the following document to troubleshoot the issue; Printer Does Not Maintain Wireless Connection.
If the issue persists, please also take a look at this helpful document; 'Printer is offline' Message Displays on the Computer and the Printer Does Not Print: Mac OS X.
Please let me know if this resolves the issue of if you require further assistance. Thanks.
Please click the Thumbs up icon below to thank me for responding.
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Please click “Accept as Solution” if you feel my post solved your issue, it will help others find the solution.
Sunshyn2005 - I work on behalf of HP

My wireless connection keeps failing.

My wireless connection keeps failing. I turn off the wireless and it resets and works however it is temporary. Any suggestions. I bought my Airport Extreme 11/2012

Hey there Chrismcknz,
It sounds like your Wi-Fi connection from your Airport is dropping and when power cycled works for a very short period of time before stopping again. I would next try a hard reset, and test the issue. Then if needed reset it to factory default and test again. The following article explains what the resets do, and how to do them:
Resetting an AirPort base station FAQ
http://support.apple.com/kb/ht3728
Hard reset: Resets the base station back to an unconfigured state, but retains the last saved configuration and any profiles so you can restore your base station from previous settings.
Factory default reset: The same as a hard reset but also removes any saved configurations or profiles.
Thank you for using Apple Support Communities.
Regards,
Sterling

My VPN connection keeps disconnecting

I live out side the uk so use a VPN connection to watch British tv but my VPN connection regularly disconnects mid way through program's, how can I stop this

I have been having same issue , it disconnects during a download and have to keep restarting the connection. I am using PurVPN.

BROADBAND CONNECTION KEEPS FAILING ! Over Six mont...

Hi all
I have broadband option 1, I never exceed my download limit. Sometimes it works fine with connection speeds between 4 and 8mb/s and I am happy with that. I use Hub 3 now on a wired ethernet connection with Wireless disabled most of the time unless I am on the laptop.
However about once every 2-3 weeks, and then every day for 7-10 days my connection goes down completely - I lose broadband altogether for between 1 and 4 hours a day. It sort of sporadically comes back up during that time but its at dial up speeds and I cant even load a full page of Google, so basically I am without a connection. Its usually in the afternoon, starting about 3-4pm or in the evening staring about 8-9pm. It has never once happened in the morning ! Ever !!!
I have tried emailing and ringing BT help desk well over 50 times in the last 6 months. I have been fobbed off with every nonsense excuse under the sun from "you are working offline" to "sometimes web pages are too busy to be loaded". I have changed my hardware to the latest Hub 3, changed all my microfilters & hub wiring. I have uninstalled my Antivirus & Firewall, Reinstalled it (Norton 2011), run full virus scans daily, done Windows updates, even tried THREE completely different PCS.
The problem persists with the same symptoms on each PC.
I think its safe to say that this isnt a problem at my end. Its sporadic. Sometimes my PC is on when it happens and I just lose the connection. Sometimes its off and when I turn it on the connections not there.
Obviously I have tried rebooting, resetting the modem, going through the whole BT online Help process but none of this brings the connection back, basically I just have to wait.
One thing I have noticed is that when this is happening my connection speed changes (initially 4-5 then 5-6 etc and currently 8-9). I have put this forward to BT as an issue - IE that they are changing my line speed and thats why my connection becomes unstable but their senior engineers deny this completely (I have the email).
So I am stuck guys.
The helpdesk is manned by very polite individuals who are friendly and try to be helpful but sadly all they do is read from Crib Sheets and really cant help at all.
On Friday they ran a line test while my broadband was down and found a fault, I was supposed to get a call back on Saturday but of course being BT that never happened so I am still waiting.
Any thoughts - I am pretty shocked BT have allowed this problem to persist for 6 months - I expected better !

Hi thanks for that. I am connected to the master socket as far as I know its a plain socket with no lines across and the plug is dead center. There is a second socket in the kitchen with a phone there is simply no way I can connect a PC to that socket and leave it there for several days to try it.
I cannot run the Speed Test - it just times out although I have run it in the past. When my connection is failing I cannot even OPEN the speedtest page let alone run it. Given that this is an intermittent fault isnt it just pointless running these things when its all working ?
When I run the quiet line test on the phone I hear a constant faint Hiss, its a corded phone so I should hear nothing - so that might be a problem
My router stats are below. ADSL Line Status
Connection Information
Line state:
Connected
Connection time:
0 days, 06:53:15
Downstream:
11.93 Mbps
Upstream:
1.067 Mbps
ADSL Settings
VPI/VCI:
0/38
Type:
PPPoA
Modulation:
G.992.5 Annex A
Latency type:
Interleaved
Noise margin (Down/Up):
6.4 dB / 6.1 dB
Line attenuation (Down/Up):
25.2 dB / 13.8 dB
Output power (Down/Up):
20.5 dBm / 12.4 dBm
FEC Events (Down/Up):
543941 / 657
CRC Events (Down/Up):
340 / 40
Loss of Framing (Local/Remote):
0 / 0
Loss of Signal (Local/Remote):
0 / 0
Loss of Power (Local/Remote):
0 / 0
HEC Events (Down/Up):
9590 / 13
Error Seconds (Local/Remote):
198 / 5
Why the heck did I have to come to the forums to find this out - why couldnt the help desk have asked me for these things ??????
Angry - yeah I'm angry !

My dial up connection keeps disconnecting!!!

hi... my dial up spends a while to even connect!!! most of the time it will just say that it does not detect a dial tone... but ive checked with other computers on the same line and its no problem... i even checked with the internet provider... please help!!!

Hi,
This may require a bit of hunting on your part, as you are on OS 10.2 and I am on 10.4. What you want to do is find the System Preference Pane that has the Modem info. On mine, it is: Network > Internal Modem > PPP > PPP Options. Here I find 'Session Options'with a check box to "Disconnect if idle for XX minutes". Un-check it. If you can find a setting like this, this may be your answer. I know it caught me in the first day or so. Failing that, SCOUR this Discussion Board, as I know I have seen other solutions -- it's just I can't remember where. Good luck.

Mouse connection keeps failing

My wireless mouse has developed the lovely problem of just losing it's connection. After a minute or two it comes back. There has been no battery warning so i don't see that as the problem.

I couldn't get into the link to check the wordage (Apple are repairing the system) but if it is not mentioned, do check out the BRAND of the batteries. Where did you buy them, were they discounted, are they a brand name like Duracell, Energiser or Apple's own.
Many batteries supplied on the cheap are not exactly the same size and that can cause a loss of connection. Is the green light steady, or if you shake the mouse does it flicker or even rattle?
All things to look carefully for.

Why does my wireless connection keep failing?

Each time I boot up my MBP, the wireless connection does not work. I have to go through the self diagnostics after bootup and then it works fine. Anyone know why this is happening?

figured it out...no issue after all

Connection keeps failing

I am trying to connect to my SAP system using Crystal reports but I get this error below each time. I am using the application server listed on my logon pad and the user name and pwd I normally log in with. Do I need to change some settings in ECC in order to allow for the connection. Thanks for any help/suggestion
Error Group
RFC_ERROR_COMMUNICATION
Message
SAP_CMINIT3 : rc=20 > Connect to SAP gateway failed
Connect_PM GWHOST=192.168.28.236, GWSERV=sapgw00, SYSNR=00
LOCATION    CPIC (TCP/IP) on local host
ERROR       partner '192.168.28.236:3300' not reached
TIME        Thu Oct 27 10:43:17 2011
RELEASE     710
COMPONENT   NI (network interface)
VERSION     39
RC          -10
MODULE      nixxi.cpp
LINE        3139
DETAIL      NiPConnect2: 192.168.28.236:3300
SYSTEM CALL connect
ERRNO       10061
ERRNO TEXT WSAECONNREFUSED: Connection refused
COUNTER     7

Moved to SAP Integration Kit forum.
Need to know what version of Crystal Reports you are using?
If it's CR 2011 install the Transport on the SAP Server which is located in this folder:
...\win32_x86\release\packages\CrystalReports\Collaterals\Add-Ons\SAP\Transports
Older versions of CR you need to download the SAP Integration Kit.
Try searching this forum for more info also.
Don

Windows 8.1 laptop not connecting to domain in branch office

We have a problem with a laptop.
It is installed in our Head office (The Netherlands), just like all other laptops by using an image.
Tested and working on the domain.
The user had to go to one of our branch offices (China) and when he connected there, the laptop just won't connect to the domain.
When he plugged in the laptop, it keeps trying to connect it's directaccess.
Other laptops (same image) immediately recognize the domain network, but this laptop just won't.
I am able to ping everything on the local network (MPLS connection), from HQ to all Branch offices but not access them.
I've tried changing the DNS settings, but without any result.
Any suggestions?

Hi,
According to this tool's description, I think it should be helpful to check system current enviroment, such as network, certificates, etc. problem. Actually according to your description, I doubt it probably network enviroment of ISP problem, but we should
find a way to verify our suspect. Then this tool would be convenient, it also would generate a trace log and it would be helpful with troubleshooting.
The DirectAccess Client Troubleshooting Tool is a graphical application, based on the .NET Framework, which checks the health of a DirectAccess client by running various tests. Built-in health tests: The following tests are currently implemented:
Network interfaces Network location (NLS and NRPT DNS) IP connectivity (6to4, Teredo, IPHTTPS, entry point in a multisite setup, DNS) Windows Firewall (applied profile, Firewall outbound rules) Certificates (EKU Client Authentication, trust chain for AIA and
CRL) IPsec infrastructure tunnel (Domain SysVol share) IPsec intranet tunnel (PING and HTTP probes) Additional features Run post-check script (PowerShell, VBScript, BAT or CMD file)
Roger Lu
TechNet Community Support

Cisco UC560 Not Clearing Static Routes When VPN Connections Drop

We have a Cisco UC560 (UC560-FXO-K9) running "Cisco IOS Software, UC500 Software (UC500-ADVIPSERVICESK9-M),
Version 15.1(2)T2, RELEASE SOFTWARE (fc1)" The issue is when we have end users connecting with the Cisco VPN Client to this device sometimes we are unable to connect to any devices on our LAN or sometimes we can't connect to the LAN on the other end of our site-to-site VPN. The one symptom I've observed when this happens is that old VPN sessions that have disconnected appear to leave static routes from the user's outside IP at their home to an IP on our LAN to a Virtual-Access interface. When this starts to happen, I restart the firewall to clear out the stale static routes and the problem is fixed, for a while at least. Below is the current state where we have the site-to-site VPN connected to our branch office and 2 user's connected with Cisco VPN clients. Below that is the static route table which has 5 total Virtual-Access interface routes (one is an extra route for a user currently connected so that their outside IP is in the static route table with 2 inside IP's associated.) Is there a way to fix the cleanup of VPN connections when they terminate?
#sh crypto isakmp peers
Peer: <branch office outside IP> Port: 500 Local: <firewall's outside IP>
Phase1 id: <branch office outside IP>
Peer: <users's outside IP #1> Port: 50420 Local: <firewall's outside IP>
Phase1 id: EZVPN_GRP_437
Peer: <user's outside IP #2> Port: 49345 Local: <firewall's outside IP>
Phase1 id: EZVPN_GRP_437
Bugsy#sh ip ro st
Codes: L - local, C - connected, S - static, R - RIP, M - mobile, B - BGP
       D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area
       N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2
       E1 - OSPF external type 1, E2 - OSPF external type 2
       i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2
       ia - IS-IS inter area, * - candidate default, U - per-user static route
       o - ODR, P - periodic downloaded static route, H - NHRP, l - LISP
       + - replicated route, % - next hop override
Gateway of last resort is <next hop of ISP for firewall> to network 0.0.0.0
S*    0.0.0.0/0 [1/0] via <next hop of ISP for firewall>
      10.0.0.0/8 is variably subnetted, 12 subnets, 3 masks
S        10.0.0.153/32 [1/0] via <non-connected IP of VPN user>, Virtual-Access2
S        10.0.0.155/32 [1/0] via <non-connected IP of VPN user>, Virtual-Access2
S        10.0.0.156/32 [1/0] via <user's outside IP #2>, Virtual-Access3
S        10.0.0.158/32 [1/0] via <user's outside IP #1>, Virtual-Access3
S        10.0.0.159/32 [1/0] via <user's outside IP #2 again>, Virtual-Access2
S        10.1.10.1/32 is directly connected, Vlan90

Hi Brian,
This sounds like you are running into the following known issue:
CSCtl03682 - EzVPN client: Several RRI routes pointing to same virtual interface
which is Dup'd to:
CSCtf39056 - RRI routes not deleted
This is fixed since 15.1(2)T4, so I would recommend upgrading to SWP 8.2 or higher. The only other way to clean up the stuck routes is to reload the router.
Thanks,
Brandon

Cannot logon via VPN connection using an ICS server

At home I have a small network set up, using a central PC A on which Internet Connection Sharing (ICS) is enabled (IP address 192.168.0.1 is allocated to this PC). PC B, having VPN client V4.0.x loaded, is connected to PC A. ICS dynamically attributes an IP address 192.168.0.n to PC B. Although a VPN connection (via IP address 194.79.185.227) can be created with a server at the office over the internet, it is impossible to perform a Windows logon and map for example a drive. When using a direct internet link via a telephone modem, it is possible to logon on the office server via the VPN connection.
I have the impression the Cisco firewall inhibits the logon, because of a IP address conflict. When looking into the "Status/Statistics/Route details" window of the VPN client, I notice the secured route 173.19.31.0 is available during the VPN connection. Using the direct telephone line it is possible to ping this address. On the same PC this is impossible, when the ICS server (PC A) is used for the internet communication. The server I am trying to reach at the office has IP address 173.19.31.1.
On the Cisco web site, I found out, that such a configuration should work. Which settings are important with this respect?

I have never found a version of ICS that works with VPN.

Since installing mavericks my imac keeps failing to connect to the internet

what is wrong with my mac i have just installed mavericks and my internet connection keeps failing any ideas

Please answer as many of the following questions as you can. You may already have answered some of them; in that case, there's no need to repeat the answers.
Restart your router and your broadband device, if they're separate. Any change?
If possible, connect to your router with an Ethernet cable and turn off Wi-Fi. Any difference?
Are any other devices on the network, and if so, are they the same?
If you can connect to more than one network, are they all the same?
Are all network applications affected, or only some? If only some, which ones?
Is networking always the same, or is the problem intermittent?
Disconnect all other devices from the network. Any change?
Start up in safe mode and test. Any difference?
Start up in Recovery mode. From the OS X Utilities screen, select Get Help Online. A clean copy of Safari will launch. No plugins, such as Flash, will be available. Any difference?
If possible, turn off Bluetooth and disconnect any USB 3 devices. Any difference?

VPN users can't connect to a Site-To-Site branch office

I have an asa 5510 that allows people to VPN into it. they get a private IP address of 10.1.4.x when they connect.
All of my sites (subnets) that are on my MPLS network were always accessible from a vpn connection.
these include the subnets
192.168.0.x (NY)
192.168.2.x (Main Office)
192.168.3.x (Main Office)
192.168.10.x (IN)
192.168.20.x (GA)
etc..
recently we converted our NY office from MPLS to a Cable Connection and added a ASA5505 for a site to site tunnel.
all of the networks in every site are able to connect to the new NY Configuration without issue.
the only issue I have is when someone VPN's into our network from home, they can no longer access the NY site.
if I try to ping anything in the NY office from a VPN connection I get this:
5
Mar 08 2013
16:22:49
192.168.0.4
Asymmetric NAT rules matched for forward and reverse flows; Connection for icmp src fiber:10.1.4.32(LOCAL\user) dst fiber:192.168.0.4 (type 8, code 0) denied due to NAT reverse path failure
I'm not sure what I need to do to get this working, so any help would be appreciated.
Thanks,
Lee

Hello Lee,
make sure you add a line in the crypto ACL of the 2 ASAs of the L2L tunnel to allow traffic between the VPN pool and the NY subnet.
make sure you add the NY subnet in the split tunnel ACL if you are using split tunneling for the VPN clients.
and make sure you have the correct NAT rules to allow communication between the 2 subnets.
also, make sure that you have the same-security-traffic command as Jay advised.
Regards,
Othman

VPN CLient TO access HO through BRanch office

We have a branch office using cisco 1841 , which makes vpn to HO (ASA 5505)
, both (1841 and asa )have VPN CLient Configured .we need Branch office VPN software client users to Connect to HO netword.i have tried but iam missimg out some where. I've attached some configs of both devices.can any one help ASAP.

Here is the URL for the Configuring and Managing Connection Entries for the VPN follow the steps for configuration which will help you :
http://www.cisco.com/en/US/products/sw/secursw/ps2308/products_user_guide_chapter09186a008015e271.html

Branch Office DC Demand Dial VPN connection keeps failing

Similar Messages

Maybe you are looking for