Broadcast Hunt In CallManager Express and SRST
Anyone know if Broadcast Hunt is now supported in CallManager Express or SRST?
Chris is right on the fact that there is no true broadcast hunting in CME. You may achieve almost the same effect by doing what is said in this thread.
http://forum.cisco.com/eforum/servlet/NetProf?page=netprof&forum=IP%20Communications%20and%20Video&topic=IP%20Telephony&CommCmd=MB%3Fcmd%3Ddisplay_location%26location%3D.1ddb7f15
I m lazy to retype it all over again. Let me know if that helps, by rating the post!
Sankar.
Similar Messages
-
Management for Callmanager express and Unity express
I will have the first Callmanager express and Unity express in our company soon. I want to get a typical configuration for the router; especially SNMP traps and Loggin statements
ThanksFor more information on the topic kindly follow the url ,
http://www.cisco.com/en/US/products/sw/voicesw/ps556/products_implementation_design_guide_chapter09186a00806e8c5c.html -
VoIP Callmanager Express newbie whos struggling
Hi,
I have been dropped into the mire as I have a basic Cisco knowledge.
I am attempting to configure a CISCO2811-V3PN/K9 with 12.3 (8), the voice line is an ISDN30 (using 10 lines)via a VWIC-1MFT-E1 and I have verified through the service provider that there is connectivity to layer 2. I have then tried following the admin guide for the Callmanager Express and have got as far as the automated Callmanager Setup to configure Dn's extra, however post this I was expecting to see some life in the 7940 phone connected up to the built in NM-ESW-16 PoE switch. I have nothing, no lights, no sign of life! Could someone please help and advise whats wrong in the config below. PLEASE!!
!version 12.3
no service pad
service tcp-keepalives-in
service tcp-keepalives-out
service timestamps debug datetime msec localtime show-timezone
service timestamps log datetime msec localtime show-timezone
service password-encryption
service sequence-numbers
hostname brwprimary
boot-start-marker
boot-end-marker
security authentication failure rate 3 log
security passwords min-length 6
logging buffered 51200 debugging
logging console critical
enable secret xxxx
username ***** privilege 15 secret xxxx
memory-size iomem 10
clock timezone gmt 0
clock summer-time PCTime date Mar 30 2003 1:00 Oct 26 2003 2:00
network-clock-participate wic 0
no network-clock-participate aim 0
no network-clock-participate aim 1
no aaa new-model
ip subnet-zero
no ip source-route
ip tcp synwait-time 10
ip cef
ip dhcp pool ITS
network 192.168.69.0 255.255.255.0
option 150 ip 192.168.69.254
default-router 192.168.69.254
no ip bootp server
ip domain name ****
ip name-server 192.168.69.1
ip ssh time-out 60
ip ssh authentication-retries 2
ip ips po max-events 100
no ftp-server write-enable
isdn switch-type primary-net5
voice-card 0
no dspfarm
controller E1 0/0/0
pri-group timeslots 1-11,16
interface FastEthernet0/0
description $ETH-LAN$$ETH-SW-LAUNCH$$INTF-INFO-FE 0/0$
ip address 10.10.10.1 255.255.255.248
no ip redirects
no ip unreachables
no ip proxy-arp
ip route-cache flow
duplex auto
speed auto
no cdp enable
no mop enabled
interface FastEthernet0/1
no ip address
no ip redirects
no ip unreachables
no ip proxy-arp
ip route-cache flow
shutdown
duplex auto
speed auto
no cdp enable
no mop enabled
interface Serial0/0/0:15
no ip address
ip mroute-cache
no logging event link-status
isdn switch-type primary-net5
isdn overlap-receiving
isdn incoming-voice voice
no cdp enable
interface FastEthernet1/0
no ip address
no cdp enable
interface FastEthernet1/1
no ip address
no cdp enable
(Same for all 16 ports)
interface Vlan1
description $ES_LAN$$FW_INSIDE$
ip address 192.168.69.254 255.255.255.0
no ip redirects
no ip unreachables
no ip proxy-arp
ip route-cache flow
ip classless
ip http server
ip http authentication local
ip http secure-server
ip http timeout-policy idle 600 life 86400 requests 10000
logging trap debugging
no cdp run
tftp-server flash:P00303020214.bin
tftp-server flash:P00305000301.sbn
tftp-server flash:P00403020214.bin
control-plane
voice-port 0/0/0:15
cptone GB
telephony-service
load 7910 P00403020214
load 7960-7940 P00305000301
max-ephones 1
max-dn 1
ip source-address 192.168.69.254 port 2000
auto assign 1 to 1
network-locale GB
create cnf-files version-stamp 7960 Jul 19 2005 15:47:21
max-conferences 8
transfer-system full-consult
ephone-dn 1
number 1001
ephone 1
scheduler allocate 20000 1000
ntp masterHi, breakwaterit,
unfortunately i am behind you on the CME curve but i was hoping you could help me with a few quick start tips. i have a 2801 with 12.3(8r). i went through the admin guide (CME 3.3) my salesman sent me but i couldn't get any of the commands to work (dhcp, . i wonder if i really have the CME program on the router? i also can't figure out how to get the automated setup tool to work. i would think this would be easy but it isn't so far. maybe i don't have CME 3.3 and i have an older version. i hope i am just missing some file or the CME app isn't started on the router. if you want you can email me directly at [email protected]
thanks -
Problem with 7920 phone and callmanager express 4.1
Hello to all, I have callmanager express version 4,1, in I registered a telephone model 7920, this telephone it receives and it makes calls without no problem, but when it makes the forward by nonanswer or by occupied to the voice mail, after reading the voice mail leaves the line retained, is to say of the 2 ephone-dn that I form to him, 1 of them this retained by the forward to the voice mail and I cannot do called by that channel somebody it knows that I must do so that the telephones or the CUE releases the line and it does not leave it retained. Thanks
Which exact SW version do you have on all tghe device involved, ?
-
Airport Express and Range Extenders and Access points.
My setup is as follows
Main wireless router is a Dlink DIR-635, with SSID 'id1'
A Edimax range extender, with SSID 'id2'
A small network with a PC and a mediaplayer connected to a Jensen router acting as a switch. This network is connected to the wireless network with SSID 'id1'
through a TP-Link access point.
I want to stream music from my PCs and Ipad to the Express using Airplay.
The 'id2' network has the best signal in the room where I want the Express.
Connected the Express to this network, but it didn't show up as an available speaker neither on the Ipad nor on my PCs.
Connected the Express to the other network 'id1'. Now it shows up on my Ipad and a portabel PC. Both connected to network with SSID 'id2'.
But the PC connected to the wireless network through the TP-link, is still unable to find the Express.
Does this sound familiar to anyone?
What protocoll does Airplay use? Does the Express send any broadcast messages to inform other devices that is is in the network?
Seems to me that the Airplay protocoll is filtered by the extender and the access point.
Any hints will be appreciated.If you are asking about "extending" or "repeating" the wireless signal, you will need both an Apple main router and an Apple extending device.
The AirPort Express (and other Apple routers) can only "extend" a wireless signal from another Apple router. -
Introducing broadcast hunt-group service for CME
Hello,
Due to popular demand I wrote this script for the purpose of ringing simultaneously more than one ephone without using shared lines. Like the broadcast hunt-group available for SIP phones, or in CCM.
http://pbevila.fastmail.fm/public/bcast.tcl
I haven't tested it completely, currently it works only when all the destinations are SCCP phones, although the objective is to allow mix and match of SCCP phones, SIP phones, pots DPs, etc.
Please try it and send any feedback here.HI Paolo
I'm attempting to take advantage of your broadcast script you have produced. I'm having a few problems not getting the calls to broadcast. At the moment I'm just playing around with it on a standalone CME with 4 stand 7941 phones. I have used the following config and also shown the output:
application
service bcast flash:bcast.tcl
Jan 4 10:45:47.139: //-1//HIFS:/hifs_ifs_cb: hifs ifs file read succeeded. size=5571, url=flash:bcast.tcl
Jan 4 10:45:47.139: //-1//HIFS:/hifs_free_idata: hifs_free_idata: 0x457E9518
Jan 4 10:45:47.139: //-1//HIFS:/hifs_hold_idata: hifs_hold_idata: 0x457E9518
param destinations 201,202
Warning: parameter destinations has not been registered under bcast namespace
I have then used:
dial-peer voice 100 pots
description broadcast hunt-group
service bcast
incoming called-number 555
failing call flow:
7941(1) - > 555 -> CME-> Broadcast (phone2,Phone3)
When I try to dial 555 from one of the phones it just comes up with number unknown and fails to broadcast. I am also running with cme 3.3 but can upgrade if needed. Also I have no analogue lines just pure VOIP at the moment. I think its some thing to do with the dial-peer? -
Broadcast Hunt Groups on UC520
Hello All,
Are Broadcast hunt groups supported on the UC520 in the latest release? Thanks
JasonHello Jason,
In Cisco Unified CME 4.3 and later versions you can use SCCP phones with the voice-hunt group
You can configure those hunt groups like this:
voice hunt-group X parallel
pilot XXXX
list XXX, XXX,
final XXX
timeout X
This type of hunt group (parallel) should ring all the phones at the same time.
Gabriel. -
Today I upgraded from my several year old Airport Extreme (3rd gen) and 2nd gen Airport Express to a new (what you'd buy on the shelf today) Airport Extreme and Airport Express. All airports are updated with the latest firmware and I'm using windows 7 for configuration.
The intention is to use the Airport Extreme as the main router, also serving wifi. And extend the network using the express. As such, the following has been done:
The Airport Extreme is configured for automatic channel, and automatic radio mode. I tried to select 802.11n 5 ghz and 802.11 n 2.4 ghz only, but it won't take the changes. Additionally, it wont' accept me using only channel 6. Not sure why, but I digress. The airport extreme is not set to broadcast a separate name for the 5ghz network.
The Airport Express is configured to use bridge mode, use an existing wireless network and is connected to my network on it's WAN port (the circle icon on the back) with ethernet. The password and wireless name used in configuration is the same as created initially on the Airport Extreme.
Initially I did the configuration of both airports on my computer, connected by ethernet to ensure stable connectivity while I inputted settings. During this, they appeared to accept the changes fine. However, when I moved the airport express to it's destination (other side of my house), the entire network went crazy.
Internet became slow, and often wouldn't load pages. This was on wired and wireless connections. When I attempted to administer the Airport in the Utility, they would not load, an error would occur. Also, at one point the Airport Extreme had renamed it self with a (2) at the end. Which was super odd. So far, the only solution has been to unplug the Airport Express and attempt to devise a solution.
Anyone have any ideas? Of course, I will continue to tinker with this, but it seems realllly strange. The previous setup was also extended (granted, using wireless only, not ethernet > wireless) and worked fine, granted it was a smidge slow, but it worked.I wanted to add this.. I followed the guide here: http://support.apple.com/kb/HT4260 to extend using ethernet, and the above is the result.
I just tried re configuring in OS X Mavericks and got the same, odd, result. -
Callmanager Express with Cisco Unified CallManager
Dear people,
I'm new to the whole voice thing, and we have a new requirement at work.
We have a cluster implementation of Cisco Unified CallManager at the head office, 2 nodes, and recently we need to integrate a branch office that has Callmanager Express...
My question starts with... Where should we start, and what should be the possible scenario
RegardsHello Saladin211,
Besides Java's nice reference, here you have another valuable info that might help you:
http://www.cisco.com/en/US/docs/voice_ip_comm/cucme/srnd/design/guide/intcmecm.html
Hope it helps, if it does please rate.
Kind regards,
- Adrian -
Get MAC-address of IP Phone using CallManager Express
Good evening,
at the moment I am developing some XML-services for Cisco IP Phones. Now I want to personalize some pages and to make that reality I need the MAC-address of the IP Phone to verify the user.
After a lot of research I found out how to do it with CallManager (use #DEVICENAME# in the url), but I didn't found out how to do it with CallManager Express. I have tried the solution for CCM in CCME, but that didn't work out. So, my question is: How can I get the MAC-address of an IP Phone with CallManager Express?
Greetings.you only have to use #DEVICENAME# when you are using a CallManager IP phone service. Under CME, simply set your services URL and the phone will automatically append the ?name=SEPXXXXXXXXXXXX parameter for you. If you configure your services URL on CME as http://10.1.1.1/MyApp the request will be http://10.1.1.1/MyApp?name=SEPXXXXXXXXXXXX
(where SEPXXXXXXXXXXXX is the device name of the phone making the request)
C -
Airport Extreme + Airport Express and Max Speed. Does my solution work?
So, I am setting up a new network, with these parameters
1) Extreme - main station, broadcasting dualband 2.4Ghz 802.11b/g/n and 5 Ghz 802.11n
2) Express - to extend network
3) Max Speed!
So from what I've read, I could "simply" do this
On the Extreme set to broadcast SSID "XYZ" on both 2.4/5
On the Express set it to Extend "XYZ" on either 2.4 OR 5, not both.
And then presto, network. However, I'm thinking this is way to simple
So my question is
1) Does the Exteme only broadcasts one network on both bands? I have seen that some posters have suggested to broadcast "XYZ" on 2.4 and then call another "XYZ 5 Ghz". If I want to maximize throughput for all devices, what should I do? Range is not an issue, both signals are perfect.
CheersFirst, there is no assurance that 5 GHz will provide you with higher throughput if the signal has deteriorated due to distance or obstructions. It is not unusual to see the 2.4 GHz band providing better throughput if the signal must pass through a few walls to reach the Express.
The point is this....the Express will choose the best signal quality based a complex formula of speed and noise. If it "sees" a better signal at 2.4 GHz, that is where it will connect. If the 5 GHz signal is of high quality, the Express will connect at 5 GHz.
Your computer will do exactly the same thing. If you are in the same room as the main router, it will connect to 5 GHz. Walk the laptop down the hall past a few rooms and around the corner and it will most likely connect to 2.4 GHz.
If you have a Mac laptop handy, move it very close to the area where you plan to install the AirPort Express. Hold down the option key on the Mac while you click on the fan shaped AirPort icon at the top of the screen. Look at the Channel information to find out whether the laptop is connected at 2.4 GHz or 5 GHz.
That will be a good indication of the band that the Express will connect to. What are your results when you try this? -
Need help with Airport Express and so on.
Ok so my main problem before getting into what I need help with here is that our MacBooks and now my iPhone 6 plus isn't staying online. Keep getting booted off and then I either have to select the network again or it will eventually go back on. If anyone has a solution or so please feel free to answer that as well. I'm running on Roadrunner with a Netgear 600 wireless router and a motorola modem. Both of which I'll leave the link to below for a better look.
My Main Question: So I'm looking at a new wireless router mainly and possibly a new modem. I know Apple products are trustworthy but how good is the Airport Express and other Airport products. Also what is the Maximum speed and Maximum data speed for the cheapest express station and if anyone knows the speeds of the other devices it would be greatly appreciated.DSL Router to Netgear 5-port Switch and I used the switch to connect to Airport Extreme, TV, Blue-Ray DVD player and DirecTV Receiver.
The AirPort Extreme base station (AEBS) is a router so it will do what you need.
You need to reconfigure your setup. Connect the WAN port of the AEBS to the DSL router. Then connect the Netgear switch to one of the LAN ports on the AEBS. The AEBS will properly share the connection. -
I am traveling with my macbook pro and I forgot to install final cut express and quicktime pro before I left. How can I in a way download them for free on my laptop from where I am? I need them and don't want naturally to buy them again!!!
Thank youAssuming you purchased QT Pro, you can always download it again at no extra charge by logging in to your Apple account.
Regarding FCE, there is no way to download & install the product. You need an original FCE install disk and your FCE serial number.
Final Cut Pro X (aka FCPX) can be purchased & downloaded from the App Store. -
I am trying to connect Garritan Personal Symphony to Logic Express and Garageband. A dialog box pops up and asks for plugin Garritan-P. Where do I find it and what do I do with it. I can't locate this plugin doing searches on any of the porgrams.
I'm not sure which version of Garritan Personal Orchestra you have or when you are getting a window pop-up, but check this link for starters:
http://afjohnston.blogspot.com/2009/11/using-garritan-personal-orchestra-gpo.htm l -
I am trying to use macro express and adobe acrobat 9 profession keeps shutting down, why is this happening? I tried to run as administrator already as well on both Macro Express and in Adobe and it still keeps shutting down.
same problem, it's been happening to me for a week or two now i'm thinking about backing up my documents and just wiping it completely, see if that works. Has anyone else tried this? I'm loosing time and have already lost a good few hours of work as it just crashes randomly. need help!!!
- saving these threads on my favourites cause i'm about to crash . . .
Maybe you are looking for
-
Hi, We are trying tom Install SAP BW 3.5 on Sun Solaris. While installing Java component of BW i am getting the following error. Can anyone please help me out of this. Thanks in advance.... Error Message 06/01/28 15:26:41 - Start updating EAR file..
-
Desktop Manager fails to start
I just installed DM6, but it always fails to start. Everytime when I start DM6 it displays a dialog box saying "BlackBerry Desktop Software has encountered a problem and needs to close. We are sorry for the inconvenience." I am using Windos XP SP3. P
-
Dial Up between Oracle on HP-Unix and Oracle on Windows 95
Hello Everybody I have Oracle Enterprise edition 8.0.4 on HP-Unix and Personal Oracle 8.0.3 on Windows 95. I want to establish connection between these two databases through dial-up. I have already established connectivity through lease line. I can d
-
The Submitter form cannot be validated if I don't fill the fields for each member of team (3). is it means that a team less than 3 persons cannot participate ??
-
Errror while running Projects Integration Request
Dear All, We are in the process of primavrea and oracle EBS 11i integration.We did all the basic setups.we tried to run Projects Integration: Synchronize Planning Resources and Planning Rates, Request completed without error . But in the log file sho