Browser response time slow but Analyzer fast with same query

Hi all,
We have a very complex query (structures and cell formulas).  When I drill and filter on a specific characteristic the action takes anything between 7 and 15 minutes when using the browser. The same query in Analyzer performing the same drilling action takes less than 35 seconds.
Our architecture is as follows:
- Relevant cubes are indexed on BWA
- WebDynPro for Java
We can see that the BWA is hit for a short time then the CPU utilization is back to 0%.  When doing '&profiling=x' on the browser I can see that the most of the time is spent on 'Get result set' / 'Get provider result set' for the Java events and on the OLAP side most time is spent on the 'Get result set' event.
Interestingly enough - when disabling myself as a user for BIA use (NO_BIA_USE) in my user profile I get the same response time on the browser.
So, does anyone have an idea of what may be the cause of the slow response time when using the browser?
Thanks
Edited by: Cobus van Rooyen on May 10, 2010 8:49 PM

Hi,
The reason is most likely because of the event ID 3200 where data transfer takes place from OLAP to frontend browser.
Record a RSTT trace for this and if you are able to see frequent calls to "Apply State XML" and "Get Result Set" then apply the SAP Note 1428850. Otherwise see which function module is causing an error.
If trace runtime is less but in browser still it takes long time then this might be because of the compression of HTPP responses, which can be confirmed by observing the sent and received data volumns from the HTTP server requests/responses. For more information refer SAP Note 746666.
Imran...

Similar Messages

  • I am a new Apple user and had a visitor, with an iPad, at my house.  I noticed the response time slowed greatly.  I have a Linksys N router and wondered is I need an Apple router to allow the speed to be consistent.

    I am a new Apple user and had a visitor, with an iPad, at my house.  I noticed the response time slowed greatly.  I have a Linksys N router and wondered if I need an Apple router to allow the speed to be consistent.

    I am a new Apple user and had a visitor, with an iPad, at my house.  I noticed the response time slowed greatly.  I have a Linksys N router and wondered if I need an Apple router to allow the speed to be consistent.

  • WebDynpro SSR / Browser Response Time

    Good morning,
    When we are visualizing a WebDynpro view we take an unacceptable response time (of almost 1 minute) and the CPU of the computer client rises almost until the 100%.
    The View is composed by a menu to the left (which is a embedded view )and a main view, which is formed by a group that contains a Table within a ScrollContainer. So, the view is not much complex.
    The table is mapped to a simple structure whose attributes are simple objects (string) and the maximum table record size is 100.
    Additionally whenever any event takes place, either or in the menu of the left or the own table, the response time remains in 1 minute although business logic is not executed.
    We have proven to delete the ScrollContainer and show the table but the performance doesn’t improve. We have also tested that communication network problems doesn’t exist.
    The performance of the client browser has been verified including the SSR parameter (“sap.session.ssr.showInfo=true”). A document with an
    image is attached, it is possible to see that the browser response time is 45 seconds to display a content of 1 MB (isn´t it too much?? Why WD generates too much HTML??).
    SAP WAS 6.40 y SP15
    Browser:Internet Explorer 6.0.2800.1106 SP1
    Thanks in advance,
    Eloy

    Hi Eloy,
    We also faced a similar problem in our project. When the page size reaches 0.5MB+ the reposonse becomes too slow.
    This is becuase WebDynpro gets marshalled data from backend and unmarshlles it based on your screen design. So in your case if you have 100 rows * 50 columns it will unmarshall all these records at front-end i.e, the client. Hence you see the response time of your CPU reaching 100 %
    You have very few options
    1) Decrease the no of visible rows on the screen at a time. Say max 10. If you have 40-50 columns explore using Tab Strips with 12-15 columns in each tab.
    2) Increase the RAM and Processing capabilities of your Client PC's. We were kind of lucky that our customer agreed to this and got P4 1GB machines.
    Lets hope the performance is improved in the future releases.
    Regards,
    Shubham

  • Safari browser seems to slow down when working with my wifi ASUS AC 68U router

    safari browser seems to slow down when working with my wifi ASUS AC 68U router - any ideas on why?

    Is your problem with Safari on the iPad, or some MacBook Air?
    Are you sure that the ASUS firmware is tested with the device having trouble and its operating system?
    Note: MacBook Airs do not run iOS.  They run Mac OS X, Windows or Linux.

  • I have downloaded several times now,but i get the same error message 'corrupt file ' how do i fix this?

    i have downloaded and uninstalled firefox several times now,but i get the same error message 'corrupt file' How do i fix this and i also go to the home page to download as well as others,i have also tried downloading to my laptop the same amount of times and i get the same error message :( very unhappy

    Set Windows Defender off and try download again from here:
    http://www.mozilla.org/en-US/firefox/all.html
    If this does not help see here:
    [https://support.mozilla.com/en-US/kb/Unable%20to%20download%20or%20save%20files Unable to download or save files]
    thank you
    Please mark "Solved" the answer that really solve the problem, to help others with a similar problem.

  • Can not connect with itunes with iphone but can connect with same password with my computer

    I can not connect with Apple ID by IPhone but I can with same ID on my computer.

    Read the article from which the thread was started.

  • HT4623 Hi everyone, I updated my iphone 3gs to ios6. But, when it come to the activation screen, It showed up could not activate iphone because the activation server is temporarily unavailable. I tried to restore many times already but it still the same.

    Hi everyone, I updated my iphone 3gs to ios6. But, when it come to the activation screen, It showed up could not activate iphone because the activation server is temporarily unavailable. I tried to restore many times already but it still the same. Help me please! T-T

    Please see the  More Like This  section on the right.

  • Webi Vs Bex Analyzer for the same query

    Hi Experts ,
    I face an issue in Webi Vs Bex Analyzer for the same query :
    Output of Bex query:
    Transport System     Location ID     Quantity
    PIPEC1-Z4          LOCCP1-Z4     1,000.000 BBL
                              LOCCP2-Z4     400 TO
                              LOCGAL-Z4     *
                              LOCRAS-Z4     200 TO
                              Result     *
    Here as the Unit of measure is different, the RESULT displays a *
    Only in cases where the unit of measure is the same, the result
    is displayed correctly.
    However in webi, the sum function blindly adds up without any possibility
    to check whether the uom is the same.
    How can I check to add only when the units are the same ?
    Regards, Jerin.

    Hi Jerin,
    Each Key Figure used in a BW query can have up to three different sets of information:
    Numeric value of the Key Figure corresponding to the Key Figure without the unit.
    Unit or Currency information, A Dimension object with character format that contains the unit or currency. For example, 'USD', 'u20AC', 'km'
    Formatted value, representing the user-specific formatting. A Dimension object with character format that contains the Key Figure and the unit (formatted value) based on user preferences configured on the SAP server. For example, '200 USD', '345 u20AC', '25 km'
    Each Key Figure is represented with a Measure object in a Class u201CKey Figures.u201D In the case where the Key Figure is configured in BW with a unit, an additional Dimension object will be added representing the unit information. The u201CFormattedu201D value represents the numeric value Formatted as a string value, following the user-specific formatting settings.
    Or if doesn't appear the Unit, for some CKF or RKF it happens, you can add to your BEx query and then to the universe the unit or currency and create a separate dimension with that information.
    I hope this help you.
    Best regards,
      Fede

  • Internet 2 times slower, but transfer speed ok

    Hi!
    Have a time capsule 1st gen connected to wimax modem via ethernet, bridge mode.
    When connecting to modem i have a 8 mbps speed, to time capsule - just about 4.
    The weirdness is that the transfer rate between pc and capsule is about 130 mbps, so the signal is ok.
    Assuming that there is no problem on the modem side (direct connection works well), what can be wrong? I tried to play with the settings on TС and sometimes it gave me about 0,5 mbps when the inner network speed was ok.
    Where to look? What do i have to change?

    Don't know what's causing it, but a few things to check are:
    -- Do you have to run the TC in Bridge mode for your setup?
    -- Make sure you're using WPA2 Personal password protection/encryption.
    -- What mode network is the TC set up for, and what modes are your PC capable of receiving. Generally, you will choose between 802.11 a, b, g, or n, or some combination of those. For most modern stuff you're going to want to use n.
    -- Newer base stations support 2.4 Gz and 5 GHz bands. 5 GHz is faster, but has more limited range (meaning, it could actually be slower if it's far away) and less ability to penetrate obstacles such as walls. This is something you need to experiment with. Not sure if your Gen 1 supports 5 GHz.
    -- You might be getting interference. Microwave ovens are notorious for this, but it can come from other sources, including cordless phones, wireless speakers, Bluetooth, DSS satellite receiver dishes, baby monitors, and other Wifi networks in the area. Try setting your TC to a specific channel instead of Automatic, and try a few different channels. There also used to be a checkbox called something like "Use interface robustness"...I think they might have changed the wording and offhand I can't remember what they call it now, but basically it can try using a few tricks to get around external interference (as I recall it uses smaller data packet sizes). Note that if you're not having problems, you want this OFF, as it will reduce speeds. But, if you are experiencing interference, it can help a lot.
    -- Make sure your TC is set to transmit a full power signal (it can be reduced, normally you don't want to).
    Just a few things to take a look at.

  • Why has my MacBook response time slowed to, at best, a crawl?

    Long ago I added available RAM, I continually delete unused apps, trash and other files. Ran virus protection software. No error messages. When I have the OS and any browser open, trying to open almost anything results only in the spinning colored disc response. Even to stop that and continue now take tens of mins or even closing down computer. What should I look for to deal with this situation?

      Woe is me.  Took it into Apple Store and Genius had to erase the hard drive and restore what was available from the Apple sites.  I do have a backup of some of my data on Carbonite, but that too is problematic since I cannot get on my account due to changing my login informatiion in a way that seems to have left my account lost to me. Guess some of my photos and videos are lost for good since I do not think I specified that they should be backed up. I am wondering why, of all things, the user has to specify backing up of photos and videos since those are often the most important and irreplacable files on the computer.  Fortunately, the best, older ones should be on DVD backups.

  • Macbook Pro Boot time and general response time slow.

    I'm running 10.9 Mavericks.
    Yesterday as I was doing my every day activites I realized randomly my macbook pro began preforming extremely poorly.
    My problems:
    Boot time now takes 2-3 minutes.
    Applications take 2-3 minutes to open.
    Applications will say they're open sometimes but will not display.
    Applications will take several tries to quit.
    Applications, especially Safari, will randomly crash.
    Everything is slower and takes a while to do, even opening a simple folder will take a minute.
    The things I have tried:
    I ran a Hardware test and the results showed it is not a hardware problem.
    I have reset the SMC and PRAM and the problems still occur.
    I have Verified and repaired the Disk/Permissions, however it seems to stop mid-way through (after about an hour).
    I can't seem to figure out what's wrong with it. I can re-install the OS but with my internet it is estimated to take 8 hours.
    Any suggestions?

    Your disk may be failing.  Do not attempt to resintall the OS until your disk is healthy.
    Backup your data immediately:
    Before proceeding you should make sure you have a current backup.  If it has been getting slower over time your disk could be a failing slowly.  SATA drives have two retry modes: short and long.  They can continue operating as read errors are increasing.  The long retry cycle is very long and can cause significant performance degradation.  If it has started long retries then it is likely to get worse and eventually fail.  SSDs also have a failure mode where the fail slowly.
    Time Machine Basics: http://support.apple.com/kb/ht1427
    Most commonly used backup methods: 
    https://discussions.apple.com/docs/DOC-3045
    Methodology to protect your data.  Backups vs. Archives.  Long-term data protection:
    https://discussions.apple.com/docs/DOC-6031
    Make a Genius Bar reservation http://www.apple.com/retail/geniusbar/ .
    or find an Apple Authorized Service Provider https://locate.apple.com/country
    If it is a failing disk, consider an upgrade to a 1 TB, 7200 RPM disk. Check out a one terabyte HGST 7K1000 7200 rpm, SATA III drive from OWC or consider an SSD.

  • AirPort Express SLOW Wifi speed-Fast with Ethernet?

    I am having troubles getting the speeds I’m paying for through Comcast. I am paying to get 105Mbps, but only receiving 61Mbps on average. I don’t expect to get 105, but 90 would make me feel better about what I am paying for.
    Here’s my problem:
    I attached my Ethernet cord and receive downloads of 125Mbps. Off the charts! Though, when I disconnect it and use Wifi it drops to 61Mbps. The highest I have receive was 71Mbps.
    I pulled up my Wireless Diagnostics and found my rate (of transfer?) is 300 Mbps. On occasion, it does drop to about 220Mbps., but usually sits at 300. My dBm (signal-to-noise ratio) is between 35-40 average. Interference is not the issue as I have moved the computer within 1 foot of the Airport Express and received these stats.
    I feel the answer lies within the AirPort Express settings. I feel as if the AirPort Express is limiting the transfer rate somehow. I do know If anyone has any ideas or needs more info to solve this crime, please respond. Thanks for the help ahead of time!
    Adam S.
    iMac (27-inch, Late 2012) running Yosemite 10.10.3
    AirPort Express 802.11n (2nd generation) Model No. A1392
    Motorola SURFboard®/ARRIS DOCSIS 3.0 SB6121 Channel bonding of up to four downstream 
channels and four upstream channels increasing data rates to well over 100 Mbps in each direction 

    Supports IPv4 and IPv6 to expand 
network addressing capabilities 

    Four times the current maximum user data throughput approximating 172 Mbps.

    I don’t expect to get 105, but 90 would make me feel better about what I am paying for.
    90 would be miraculous for an Internet connection through the WAN port on the Express for a wireless broadcast, even if the wireless device was close to the Express. Take a look at recents tests of the Express:
    http://www.smallnetbuilder.com/tools/charts/router/bar/113-5-ghz-dn-c
    40 Mbps was top speed for 2.4 GHz
    42 Mbps was top speed for 5 GHz
    If you are getting 60, you are doing very well indeed.....quite a bit above average for an Express
    I checked my 2nd Gen Express again and on a 100 Mbps Internet connection, I got 44 Mbps at 2.4 GHz and 45 Mbps at 5 GHz with the laptop located a few feet from the AirPort Express.
    If you are doing better than that, I would call it a day.

  • Why is ethernet slow but wifi fast in Safari on iMac

    Suddenly Safari is very slow at rendering pages. When I disconnected ny ethernet cable and relied on wifi it is now very fast. What is causing this?

    This is what I get Barney -
    Last login: Sat Sep 21 10:05:35 on console
    Denis-Scotts-IMac-2:~ denisscott$ ifconfig
    lo0: flags=8049<UP,LOOPBACK,RUNNING,MULTICAST> mtu 16384
              options=3<RXCSUM,TXCSUM>
              inet6 fe80::1%lo0 prefixlen 64 scopeid 0x1
              inet 127.0.0.1 netmask 0xff000000
              inet6 ::1 prefixlen 128
    gif0: flags=8010<POINTOPOINT,MULTICAST> mtu 1280
    stf0: flags=0<> mtu 1280
    en0: flags=8863<UP,BROADCAST,SMART,RUNNING,SIMPLEX,MULTICAST> mtu 1500
              options=2b<RXCSUM,TXCSUM,VLAN_HWTAGGING,TSO4>
              ether 10:9a:dd:4a:e8:d8
              media: autoselect (none)
              status: inactive
    en1: flags=8863<UP,BROADCAST,SMART,RUNNING,SIMPLEX,MULTICAST> mtu 1500
              ether c8:bc:c8:c4:08:23
              inet6 fe80::cabc:c8ff:fec4:823%en1 prefixlen 64 scopeid 0x5
              inet 192.168.178.35 netmask 0xffffff00 broadcast 192.168.178.255
              media: autoselect
              status: active
    p2p0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> mtu 2304
              ether 0a:bc:c8:c4:08:23
              media: autoselect
              status: active
    fw0: flags=8863<UP,BROADCAST,SMART,RUNNING,SIMPLEX,MULTICAST> mtu 4078
              lladdr dc:2b:61:ff:fe:e1:03:80
              media: autoselect <full-duplex>
              status: inactive
    utun0: flags=8051<UP,POINTOPOINT,RUNNING,MULTICAST> mtu 1380
              inet6 fe80::783d:25ba:eb99:b39c%utun0 prefixlen 64 scopeid 0x8
              inet6 fdd6:3e99:8980:4856:783d:25ba:eb99:b39c prefixlen 64
    vnic0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> mtu 1500
              options=3<RXCSUM,TXCSUM>
              ether 00:1c:42:00:00:08
              inet 10.211.55.2 netmask 0xffffff00 broadcast 10.211.55.255
              media: autoselect
              status: active
    vnic1: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> mtu 1500
              options=3<RXCSUM,TXCSUM>
              ether 00:1c:42:00:00:09
              inet 10.37.129.2 netmask 0xffffff00 broadcast 10.37.129.255
              media: autoselect
              status: active
    Denis-Scotts-IMac-2:~ denisscott$ defaults write com.apple.mail DisableInlineAttachmentViewing -bool yes
    By the way, at the moment I do not have my ethernet cable plugged in.

  • I use Firefox. My MacBook Pro is pretty low on space. I've been told that Chrome is a "lighter" browser, therefore my Mac might run faster with Chrome true?

    I am trying to unload applications I do not need and moving video/pix files to other storage locations

    hello hlascarro, i don't think that the sentiment that chrome would be "lighter" than firefox can be considered valid - i'm on windows, so i cannot say if it's the same for mac too, but the chrome install-folder here takes nearly triple the amount of disk space than firefox (138MB vs. 50MB) and in numerous browser comparisons firefox was generally also using less RAM resources...
    <br>http://www.tomshardware.com/reviews/chrome-27-firefox-21-opera-next,3534-9.html
    <br>http://lifehacker.com/5976082/browser-speed-tests-chrome-24-firefox-18-internet-explorer-10-and-opera-1212

  • Aplle computers locating Time Capsule; but, no luck with PC

    My PC cannot identify my Time Capsule router? Anyone experiencing the same problem? Any suggestions? No problems with connecting to my Mac computers.
    Thanks,
    Jay

    I had the same problem,
    1- install the new airport software from the apple web site, under downloads on the mac
    2-in the airport utility under manual setup / go to disk / check enable file sharing / under workgroup type in MSHOME
    3-update
    4- on the pc in control panel / performance and maintenance / system / computer name / change workgroup to MSHOME
    5- remove existing windows airport software
    6- pc go to step 1 / apple web site download airport software for windows / install / password access should be same as the airport disk utility
    the apple web site downloads are an updated version, this was what I did with a little help from everyone here on this discussion. My Daughter uses the pc for college and the backup with norton 360 works great.
    Let me know how it works out
    Thanks Mike

Maybe you are looking for