BT Hub 4 Ip address change

My home hub 4 is set to 192.168.1.254, this is on the same subnet as my office, I cannot connect to my office now. Have changed to the 172 address option but I am now unable to connect my computer to the hub why will the laptop now not connect.

Did you change the DHCP range on the hub?
If not it will be giving out DHCP addresses in the old range which are in the wrong subnet. You will either have to manually change your PC IP address so you can access the HUB again or reset the hub to factory settings and start again.

Similar Messages

DMVPN Hub IP address change

I have a 2-Hub DMVPN setup with 10 spokes. One hub in NJ and one in Australia. I am migrating to NJ office to a new ISP and will obviously have an IP address change. What is involved in changing the IP of the NJ router?

Hello
On configuration front, only the following to be done
NJ Router:
tunnel source to be changed to new IP address
IP address of the physical interface towards the IP & Routing
All Spoke Routers: in the tunnel
no Ip nhrp map multicast <old Physical IP at NJ>
no ip nhrp map <NJ tunnel IP> <old Physical IP at NJ>
Ip nhrp map multicast <New Physical IP at NJ>
ip nhrp map <NJ tunnel IP> <New Physical IP at NJ>
From the migration point of view, What I would suggest is start from one of the Spoke router and remove its configuration related to NJ and make sure that it works with Australia Hub, then you can do the migration of NJ router ( All other spokes should fall back to Australia) and Join the previous Spoke to test . If that is successful, you can plan for the migration of the all other spokes
Hope this helps
Harish.

IP address changing

I made the mistake of getting BT Infinity when it became available in my area on the 28th May this year.
After many dsconnections an openreach engineer came out in mid July and spent 4 hours checking everything before realising that the initial installation hadnt done correctly in theh cabinet and that they hadnt put the new master socket on.
After more disconnections, most of which are only brief and a few more longer ones I contacted BT again and a second engineer called on the 20th August saying I had complained about a lack of speed. I told him that the speed was fine when it was connected but it dropped the connection sometimes and the main problem was that the IP address frequently changed, even if I hadnt noticed the orange ligh being on the router or it had stoped me surfing the web.
As I wanted to set up a FTP server, as I had done with previous ISPs, for family and friends to share files, I needed a stable IP address and I knew I had a dynamic address but that should stay the same unless I switch off or reboot the router. He checed everythinghe could and eve chnaged the new B home Hub 5 in case that had a fault that wasnt showing and thought that it may be a problem between the BT servers and the exchange as it showed on the schematic that BTs own diagnostic test had identified on the track a fault page as the building housing the server were outlined in red.
Needless to say it is still dropping occassionally and the IP address is constantly changing. I think it did keep the same IP for 48 hours once but usually it will change at least 3 or 4 tmes per day. Between 00.34 and 22.40 yesterday, the 22nd September, it has changed 9 times and had the orange light on the Home Hub 5 at least twice for several minutes, when I could neither send and receive emails or surf the web.
I went to check what was happening on the track a fault page and saw that even though this was an ongoing fault from the initial installation, there were two closed faults even though I was still waiting for BT support to call me back as promised last Saturday afternoon, they did call but hung up on me as soon as I had said "Hello" so I was expectin them to call back or email me.
I then sent a message using the contact us form on the BT site.
I was called this afternoon and was on the phone for the best part of 4 hours either talking to many different people at BT, waiting for them to call back or on hold, explaining over and over again that my main problem apart from the line disconnecting was the frequent changes of the IP address and if they could not provide a stable one that only changed when I switched the router off then I wanted to cancel without any penalties for early termination as there was a fault that BT could not fix.
I was told by one "technical" support guy that the IP can change every 24 hours, which I agreed that if it was set for a 24 hour lease period and I switched the router off and the lease expired before I switched it back on that it would change but that if the router was left on then it should not change while I was using it. Bearing in mind I have had this discussion many times over many months with various BT support personnel I have given them long enough and asked to be trasnferred to someone who could tell me if I could terminate my contract as BT was in breach of their contract to supply me with a stable connection.
He said he was transferring me, after 30 minutes on hold I ended up in the sales department where a very nice chap told me that he would transfer me back to technical again as they needed to put a note on my file saying what they had told me about being unable to provide a stable iP address and to then transfer me to the correct department. On hold again then explain everything agan etc etc then transfer to customer options where I was told I could cancle if I paid over £300 in fees or I could take out a business package to get a static IP.
I was also told that it was in the T and Cs that they did not have to provide me with a stable IP address. I asked him to send me an email with the part that said that and he said he will do that tomorrow and will also call me back tomorrow afternoon.
I have had a look on the T and Cs from a link on this site and using the find next box in internet explorer, there is no mention of IP or address, so I do not know where he will find the part about not having to provide a stable IP address.
I have tried to keep this as short as possible but as I have summarised and condensed 3 months worth of discussions into these few paragrpahs, it does appea to ramble on a bit, sorry.
Can anyone tell me definitively if I am correct in expecting BT to provide me with a connection that doesnt drop more times in just over the 3 months that I have been with them than in the previous 12 years I have had an internet connection with varous ISPs and aslo are they correct in stating that they do no have to provide an IP address that doesnt change even if I do not switch off or reboot the router as I am on a residentia package with a dynamic IP.
Thanks for hopefully taking the time to read through this post and for any help you can give me

Its not essentail that I have a static IP as its for personal use only not for a business but as you have stated it can take a while for the updated IP address to propogate and even if it instantly updated the new IP address I dont think anything would propogate quickly enough to be of any use when the IP can change as often as 9 times in less than 24 hours, as it did yesterday.
All I am asking for is an IP addresss that doesnt change unless I switch the router off or have a power cut. Surley that should be a simple enough thing to arrange.
I can even put up with the temporary connection drops, as long as they only last for a few minutes a few times a week and not as regularly as they are doing at the moment.
Could a mod please merge this thread with the other one in the Infinity section and place them both in the Infinity section as I would like to know if other Infinity users are having frequent I address changes and there is more chance of them seeing this thread and replying to it if it is in that section.
Thank you.

Connected dynamic VPN wan address change

I have a hub and spoke VPN. The spoke is dynamic.
If once the tunnel is established the WAN address changes the router doesn't know to start a new session and the VPN TAKES ages to come up as it still thinks it has an active tunnel.
Any idea how I can reduce the time for the tunnel to re-establish?

Hello Martin,
You got to change the security-association lifetime:
set security-association lifetime #
Give it a try and let us know.
Regards,
Julio

Email address change not showing on ipad after sync

iTunes email address change not showing on ipad after sync

So change it.
Open iTunes, scroll to the bottom of the main page, tap your account name, log out then sign in with the correct name.

HP LaserJet Pro P1606dn ip address change automatic

i have a HP LaserJet Pro P1606dn, there is problem with IP Address, ip address change automatic in this reason i am not able to use the printer, pls solve my problem....

Hi @Naksain,
I see by your post that the printer's IP address changed automatically and you can't use the printer now. I can help you with this.
From the Configuration page, get the printer's IPV4 address, try and access the Embedded Web Server for the printer.
Type the IP address into your web browser's address bar. (Internet Explorer)
Printing a Configuration Page.
If you can still access the printer's Embedded Web Server, then create a new port with the new IPV4 address.
Go to start, devices and printers, right click the printer, go to printer properties, select the ports tab.
Click Add Port, select Standard TCP/IP Port, then select New Port and follow the wizard.
Type in the proper IP address for the printer.
Make sure the printer is online.
Test the printer.
Setup a Static IP address for the printer, this way the printer will keep the assigned port.
Printer Does Not Maintain Wireless Connection.
Disregard the title. Under Windows, go to Solution four: Assign your printer a static IP address.
Just use the IPV4 address already assigned to the printer.
If you need further assistance, just let me know.
Have a nice day!
Thank You.
Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
Click the “Kudos Thumbs Up" on the right to say “Thanks” for helping!
Gemini02
I work on behalf of HP

In Blackberry Z 10 "HUB MANAGEMENTS", automatically changes the items that are included in my main View of the Hub Managements.

In Blackberry Z 10 “HUB MANAGEMENTS”, automatically changes the items that are included in my main View of the Hub Managements.
I really don’t know how it happens, “Off or On” thing, without knowing me. When any Email hits to my device and not shows in my “HUB MANAGEMENTS”, at that point of time I come to know, it’s Off again.
Then whole process again, I go in “HUB MANAGEMENTS” and switch it on again and again.
I need Blackberry Z10 OS developers focus on this issue…

I can confirm this behaviour and it defeats the purpose of having a hub.
Could a BBTA confirm that this has been filed or even solved internally?
Olivier - interfaSys ltd
Developing for BlackBerry 10 devices using the Sencha Touch framework.

Not able to access object after server IP address changes

I have an Activatable object that gets registered with the RMIDs registry.
If my servers IP address changes, then when I look up the remote object, I can retrieve it from the registry, but as soon as I make a method call I get an access denied to xx.xx.xx.xx, where xx.xx.xx.xx is the old IP address - and not the new one.
I've tried rebinding the object to the registry after the IP address has changed but with no success.
I've also tried settings -Dnetworkaddress.cache.ttl=0. All my lookups are done by hostname.
Any ideas?
TIA
Ian

If the server changes its IP address all stubs which have already been exported become invalid and must be reacquired. For an Activatable this also means that you must re-register the object as an Activatable as well as rebinding it.

How to deal with dynamic IP address changes

I have installed Fodero C3 and Oracle 10g successfully. Oracle 10g use web OEM console to manage database. However, my internet provider only provided me a dynamic IP address. When I installed Fedora C3, Linux server automatically picked a Hostname like " ip12-345-678-90.dc.dc.cox.net". After I created database, all database files also used this hostname. Then Oracle web OEM console worked fine. Due to the dynamic IP address assigned by ISP, their DHCP server changed the first part of IP address(ip12-345-678-90)frequently to another one. After IP address changed, I couldn't start up web OEM console and listener because they couldn't find correct hostname (IP address). I have talked to my ISP. It seems that it can not be solved. Anyone knows how to deal with this problem through 10g and OEM console themseleves. I also think about to configure Linux server to solve the problem. I really need your help. Thanks in advance

Thank all of you so much to respond my questions. I think I have solved the problem. Since the key point was that Oracle 10g OEM console could not work with the frequent changes of IP address made by my ISP. I just bought a 54G wireless router. Then connecting router to cable modem. The cable modem still gets the dynamic IP from ISP, but the router automatically assigned a static IP address to my Linux system with the range from 192.168.0.0 - 192.168.255.255. This IP was control by my router. It is nothing to do with ISP. So I re-created Oracle database with this new static IP. Then OEM console and listener can startup and connect to database without problem. I do think other guru's methods also will work. I just have no time to try them one by one. Thanks again. Your inputs make me learn many things.

Ship-to address changes on customer master not updating orders

We have recently noticed that ship-to address changes on the customer master made with XD02 no longer show up on existing standard orders. Similar changes to the sold-to addresses do show up but no tthe ship-to addresses. Does anyone know how we can resolve this problem?

hi jeff,
the adresses of a partner is
- with reference to the master-data ( if unchanges in the Order )
- of copied in the order and then changed and saved onlyy for the order.
in the first case, a change of the main data will effect a change in the order.
in the second case, the change of the main data will not change the order, data - they are separate.
you can see this in se16 / table vbpa.
look at the adressnumber.
Adressnumbers of 9++++ are of the 2nd - manual type.
I guess, in the ship to partner, there is done a manual change in the order.
in solt to data normally you don't need such a change. therfor the sold-to partner will get the changes of masterdata -- the ship to partner has manual adress of the orden.
hans

Login to Java Desktop fails after IP address change

If the IP address (or networking type DHCP vs. static address) changes, users can no longer log in to their accounts and use the Java Desktop environment. I can get around this by using the Solaris Management Console from CDE to remove the user(s) without removing their respective home directories, then recreating the users with the respective home dirs. This, however, seems to be an extreme hack to me. Is there a better way? Thanks.

Hi Glenn,
The issue could be caused by unfinished AD replication. It may be intermittent and resolve itself automatically.
For more detailed information, please refer to the thread below:
File Replication and 2008 R2 standard
http://social.technet.microsoft.com/Forums/windowsserver/en-US/583182b6-49e8-4836-970b-a881c2d52773/file-replication-and-2008-r2-standard?forum=winserverfiles
Best Regards,
Mandy
We
are trying to better understand customer views on social support experience, so your participation in this
interview project would be greatly appreciated if you have time.
Thanks for helping make community forums a great place.

HT5622 My email address changed, my iCloud still has my old address. Do I just cancel the existing one and open a new one under the new address or what?

My email address changed, my iCloud still has my old address associated with it. Do I just cancel the old iCloud and start awe one or what?

Hello sheryfromzaf
Check out the articles below to go through the steps of changing your Apple ID and then what to do after you change your Apple ID. You will probably not have to change all the Apple ID for all services, just the ones that you use.
Apple ID: Changing your Apple ID
http://support.apple.com/kb/ht5621
Apple ID: What to do after you change your Apple ID
http://support.apple.com/kb/HT5796
Regards,
-Norm G.

Updating a vendor table when address changes in infotype 6

hello all,
when an employee changes his personal information in the PZ02 service, it updates the infotype 6, as soon as the update is done it has to update the LFA1 or LFB! vendor table.
is there a workaround for this
BR
venu

thanks for the reply.
whenever there is an address change in IT6 it should update the vendor table(for eg: if changes are done in PA30 and not from ess, so its kind of generic version that i have to create to update the vendor table either from ess or PA30).
i am already using the HR_ESS_ADDRESSDETAIL and HR_ESS_ADDRESSLIST for changing the fields on the iview.
(t77www_sc)and linking it to pz02.so what u mean is i can go ahead and write the code in the same module for updates.
is this is the only way to do it, or we can do it by BAPI_address_change.
I am trying to know all the different ways it can be done.
a)can i use a BAPI if so which one?
b) can i do it thru workflow.
c)or user exit.
Please help me out with details
thanks
venu

Restricting the partner address change in both VA01 & VA02

Hi All,
In Sales Order Creation / Change i need to make the partner address fields editable but want a restriction on save.
For that i am doing the following:
Change:
This is possible by restricting the update comparing YVBPA & XVBPA table using parameter UPDKZ.
Create:
In the create scenario YVBPA table remains empty.Are there any other tables I should look at to restrict this address data change?
However, there is a table XVBADR , changes to which do not influence the final display address.
Alternatively , do we have an alternative approach to restrict the partner address change in both VA01 & VA02?
Thanks in advance!!!
Regards,
AP

Resolved by using YVBPA & XVBPA tables.

ACS 4.2.0 AAA-server-IP-address changing to 169.254.x.x

Hello,
I have ACS 4.2.0.124.15 installed on a windows server 2008.
In the configuration menu : network config > AAA server , the AAA-server-IP-address change to 169.254.x.x each time I disconnect the ethernet interface of the server.
Allthough, the ip adresse in my network connection of the windows-Lan-connection is set to static.
Whe I reconnect the ethernet interface of the server, it stays in 169.154.x.x. And I need to reconfigure the real static adresse each time.
Do you knows this problem. Is it a way to avoid it ?
Michel Misonne

Hello,I have ACS 4.2.0.124.15 installed on a windows server 2008.In
the configuration menu : network config > AAA server , the
AAA-server-IP-address change to 169.254.x.x each time I disconnect the
ethernet interface of the server.Allthough, the ip adresse in my network connection of the windows-Lan-connection is set to static.Whe
I reconnect the ethernet interface of the server, it stays in
169.154.x.x. And I need to reconfigure the real static adresse each
time.Do you knows this problem. Is it a way to avoid it ?Michel Misonne
Hi Michel,
It was issue in ACS 1113 SE Appliance and clear solution for the above is mentioned in the below link
http://www.ciscosystems.com/en/US/products/sw/secursw/ps2086/products_tech_note09186a00808d9199.shtml#stat
HTH
Ganesh.H

Partner Function Address change at line item level - Item Partners checkbox

Hi guru, we have a requirement that we need to change the address for partner function at line item level without changing the partner number. Currently the ship-to partner function address is automatically coming from the header although the number is modifiable but not the address (when double click into the partner number, the pop-up is grayed out). It is probably because the Item partner check box for the shipto partner is not checked (field name: SD_PARTNER_POSFLAG). However that field is not modifiable in VA02 either.
If the shipto partner number is overwritten, then the item partner check-box is automatically checked and allows address chanage. Is there a way in the configuration that can default the 'item partners' checkbox for certain partner so the address can be changed without the need to overwrite the account?
Any advice is appreciated.
Thank you.

If the item level ship-to party is derived from header partner function, but you want to change the address at item screen rather than header level. On item screen, enter the same function, the same number again in a new line, "item partner SD_PARTNER_POSFLAG" is then ticked. Then proceed to the address change.
No need to do modification.

BT Hub 4 Ip address change

Similar Messages

Maybe you are looking for