By passing Kona for direct firewire capture/control

Greetings
First let me qualify this by saying that it's quite possible I'm missing something very basic in FCP and MAC config and use. I'm not immune to overlooking the obvious or stupid mistakes. So having said that...
I'm running a FCP 5 on a MacPro with a Kona AJA card.
In the course of trying to capture HD video from a Sony HVR-M25U deck I've had problems matching capture res/format and deck control. Tried every possible combo of capture and control preset available.
To make a very long story short, the best I could do was capture 1080i via the "capture now". (Obviously I don't get TC from the tape which will cause problems in future edit sessions.)
In the course of many discussions a possible problem might be that the KONA card is some how preventing direct Firewire capture and control.
So my question is, is there an easy way during boot up to disable the KONA? If there is a way it would (probably) allow a standard firewire ingest.
I hope this makes sense.
I guess what I'm asking for is a way to fool my Mac into thinking there is no KONA without having to physically remove it from the slot.

You don't have to disable the Kona to capture firewire, just select an appropriate easy setup (non Kona)
so you have a Kona LE?
What we usually do with HDV that needs to be repeatable or be used in other systems is bump to HDCam with new code (to avoid TC breaks) then capture the result of that.
If it doesn't need to be repeatable we come in pro res or DVCProHD so editing/ finishing is a frame based codec.
If you have hdmi on the deck and or camera you might want to look at
http://www.convergent-design.com/CDProductsHDConnectMI.htm
or via firewire
http://www.convergent-design.com/CDProductsHDConnectSI.htm
check them out at creative cow read, research, verify

Similar Messages

Passing parameters for a query throught XML and capturing response in the same

Hi All,
I have defined a RequestParameters object and i am passing paramerts for a query through XML and trying to capture the result in the same and send back to the source. In this case i am send XML from excel.
Below is my XML format.
<?xml version="1.0" encoding="utf-8"?>
<s:Envelope xmlns:s="http://schemas.xmlsoap.org/soap/envelope/">
<s:Body xmlns:xsi="http://www.w3.org/2001/XMLSchema-instance" xmlns:xsd="http://www.w3.org/2001/XMLSchema">
<Insert xmlns="http://tempuri.org/">
<dataContractValue>
<dsRequest>
<dsRequest>
<SOURCE></SOURCE>
<ACTION>Insert</ACTION>
<RequestParams>
<RequestParams>
<ACC_NO>52451</ACC_NO>
<EMP_CITY>HYD</EMP_CITY>
<EMP_NAME>RAKESH</EMP_NAME>
<EMP_CONTACT>99664</EMP_CONTACT>
<EMP_JOM>NOV</EMP_JOM>
<EMP_SALARY>12345</EMP_SALARY>
</RequestParams>
<RequestParams>
<ACC_NO>52452</ACC_NO>
<EMP_CITY>HYD</EMP_CITY>
<EMP_NAME>RAKESH</EMP_NAME>
<EMP_CONTACT>99664</EMP_CONTACT>
<EMP_JOM>NOV</EMP_JOM>
<EMP_SALARY>12345</EMP_SALARY>
</RequestParams>
</RequestParams>
</dsRequest>
<dsRequest>
<SOURCE></SOURCE>
<ACTION>Update</ACTION>
<RequestParams>
<RequestParams>
<ACC_NO>52449</ACC_NO>
<EMP_CITY>HYD1</EMP_CITY>
<EMP_NAME>RAKESH1</EMP_NAME>
<EMP_SALARY>1345</EMP_SALARY>
</RequestParams>
<RequestParams>
<ACC_NO>52450</ACC_NO>
<EMP_CITY>HYDer</EMP_CITY>
<EMP_NAME>RAKEH</EMP_NAME>
<EMP_SALARY>1235</EMP_SALARY>
</RequestParams>
</RequestParams>
</dsRequest>
</dsRequest>
</dataContractValue>
</Insert>
</s:Body>
</s:Envelope>
Where i have a List of dsRequest and RequestParams, where i can send any number of requests for Insert,Update. I have two a XML element defined in RequestParams "RowsEffected","error" where the result will be caputred and is updated
to the response XML.
I have 6 defined in RequestParams
EMP_SALARY(int),ACC_NO(int),EMP_CITY(string),EMP_NAME(string),EMP_CONTACT(string),EMP_JOM(string)
My Question is:
When i am trying to build response XML with the following code, the parameters which are not given in the Request XML are also appearing in the Response.
                ResponseParams.Add(
newdsResponse()
                    ACTION = OriginalParams[a].ACTION,
                    SOURCE = OriginalParams[a].SOURCE,
                    Manager = OriginalParams[a].Manager,
                    RequestParams = OriginalParams[a].RequestParams
Where the OriginalParams is dsRequest
Ex: In my update query i will only send three parameters, but in my response building with ablove code, i am getting all the variables defined as INT in the RequestParameters.
Is there any way i can avoid this and build response with only the parameters given in the Request ??
Appreciate ur help..Thanks
Cronsey.

Hi Kristin,
My project is, User will be giving the parameters in the excel, and using VBA, the values are captured and an XML is created in the above mentioned format and is send to web service for the Insert/Update.
I created a webservice which reads the values from <datacontract> and it consist of list of <dsRequests> where any number of Insert/Upate commands can be executed, with in which it contains a list of <RequestParams> for multiple insertion/Updation.
//function call
OriginalParams = generator.Function(query, OriginalParams);
where OriginalParams is List<dsRequest>
//inside function
command.Parameters.Add()// parameters adding
int
val = command.ExecuteNonQuery();
after the execution,an XML element is added for the response part.and it is looped for all the RequestParams.
OriginalParams[i].Result.Add(
newResult()
{ ERROR = "No Error",
ROWS_EFFECTEFD = 1 });
//once all the execution is done the response building part
for(inta
= 0; a < OriginalParams.Count; a++)
                ResponseParams.Add(
newdsResponse()
                  Result = OriginalParams[a].Result
QUEST: When i am trying to build response XML with the following code, the parameters which are not given in the Request XML are also appearing in the Response.
Ex: In my update query i will only send three parameters, but in my response building with ablove code, i am getting all the variables defined as INT in the RequestParameters.
Is there any way i can avoid this and build response with only the parameters given in the Request ??
Appreciate ur help..Thanks
Cronsey.

KONA LSe PCIe SD capture card.

Hello there...
Just wanted to pick your brains... I've just finished a long run of work and the boss wants to sort out the edit suite and see if we can improve overall performance etc...
One of the things that was recommended to him by another editor was to invest in a KONA LSe PCIe SD capture card... which sounds all very good but we only shoot on DVcam...
However, even though we won't capture any 10/8 bit uncompressed, am i right in thinking the card would be useful in handling effects etc, therefore reducing the strain/workload on the processors?
In a nutshell... is there any advantage to installing this card, even though we NEVER capture uncompressed media?
Thanks for your opinions.
J,

Increased performance? Render handling? RT effects? Not if you capture DV via firewire. You might get slight performance improvements with footage you captured with the card, but it will not enhance anything, really. Definately not firewire captures. The HD cards do some load bearing processing for HDV and DVCPRO HD, but nothing considerable.
If you capture, edit, and output DV, there is no reason to get this card.
Shane

Is firewire capture broadcast quality?

I know the data rate from firewire is only 3.6MB per sec. i have only a sony DSR11 dv deck which has only firewire, i figured out that if i want uncompressed 8.5mb per sec i need component out, video capture card and a bigger deck. right now, my clients are happy with the output,and the tv stations are accepting the outputs i am giving but i wonder if it is really broadcast quality . thanks
yours
sameer

Hi Sameer
What do you understand to mean by broadcast quality?
Generally, a broadcaster will provide a set of strict guidelines, on the technical side mainly related to legal chroma and luma limits, limitations on flashing imagery etc, and on the artistic side sometimes relating to the quality of image. Broadcasters differ and so do their levels of tolerance relating to these guidelines.
By firewire capture I think you mean DV quality footage. You can capture uncompressed footage over firewire too.
As Denis said, converting DV footage to uncompressed won't improve the quality of your footage - it is still originating from a compressed source - however it might allow you to perform more exacting grading on the images and bring it within legal broadcast limits.
Most of the broadcasters I have worked with have required footage to be provided on Digibeta masters but that doesn't mean you couldn't take a Mini DV tape to a facilities house and have them convert it over before you submit for broadcast.
At the end of the day, if the broadcaster accepts your footage, it is broadcast quality in their eyes and you have no problems. For your own peace of mind, though, do make a legalisation pass to make sure your footage will conform when seen on other televisions.

Certification- Passing requirements for SAP?

Does any one know what is the % for passing for Sap MM. How many questions need to be correctly answered for getting through this.
Regards
AH

Hi
For SAP MM certification exam you will get 80 questions in different areas like Purchasing,Inventory,LIV etc.,. you have to score minimum 70% to clear the certification.
Pls see the below details for your reference.
Certification Test
SAP Consultant Certification Solution Consultant SCM - Procurement with mySAP ERP 2005
Booking Code
C_TSCM52_05
This certification path proves your fundamental understanding of the procurement functionality available with SAP Supply Chain Management (SAP SCM) coupled with SAP ERP 6.0, enabling your client or company to get parts and products at the right time and meet your deadlines. With this certification, youll be able to apply this knowledge as a solution consultant in a team setting.
Software
Software components: SAP Enterprise Central Component (ECC) 6.0
Number of Questions
80
Duration
180 minutes
Notes
Please note that you are not allowed to use any reference materials during the certification test (no access to online documentation or to any SAP system).
The certification test Solution Consultant SCM - Procurement with mySAP ERP 2005 verifies the knowledge in the area of the Procurement] for the consultant profile. This certificate proves that the candidate has a basic understanding within this consultant profile, and can implement this knowledge practically in projects.
Competency Areas
The following list helps you to identify the competency areas covered in this test. The percentage indicates the portion of the test dedicated to a particular competency area.
Way(s) to attain
Competency Importance Topic Primary Alternative Other
SAP u2013 Overview
< 10% SAP navigation SAP125, ERP001, SAP210 SAP01
Management Empowered by SAP ERP ERP001
Procure-to-pay SAP210 SCM500
Procurement Process
11-20% Purchase requisitions TSCM50, SAP210 SCM500
Purchase orders TSCM50, SAP210 SCM500
Requests for quotations TSCM50, SAP210 SCM500
Procurement for stock TSCM50, SAP210 SCM500
Procurement for direct consumption TSCM50, SAP210 SCM500
Subcontracting TSCM50, SAP210 SCM520
External services TSCM50, SAP210 SCM500
Reporting TSCM50, SAP210 SCM500
Master Data
< 10% Material master TSCM50, TSCM52, SAP210 SCM520
Vendor master TSCM50, TSCM52, SAP210 SCM520
Purchasing info records TSCM50, TSCM52, SAP210 SCM520
Source list TSCM50, TSCM52, SAP210 SCM520
Quota arrangement TSCM50, TSCM52, SAP210 SCM520
Messages TSCM50, TSCM52, SAP210 SCM520
Purchasing Optimization
11-20% Contracts TSCM50, TSCM52, SAP210 SCM520
Scheduling agreements TSCM50, TSCM52, SAP210 SCM520
Invoicing plans TSCM50, TSCM52, SAP210 SCM520
Document release procedure TSCM50, TSCM52, SAP210 SCM520
Purchasing document configuration TSCM50, TSCM52, SAP210 SCM520
Inventory Management
> 20% Goods receipts TSCM50, TSCM52, SAP210 SCM510
Goods issues TSCM50, TSCM52, SAP210 SCM510
Stock transfers TSCM50, TSCM52, SAP210 SCM510
Reservations TSCM50, TSCM52, SAP210 SCM510
Consignments TSCM50, TSCM52, SAP210 SCM510
Physical inventory TSCM50, TSCM52, SAP210 SCM510
Availability check TSCM50, TSCM52, SAP210 SCM510
Transaction types TSCM50, TSCM52, SAP210 SCM510
Messages TSCM50, TSCM52, SAP210 SCM510
Valuation and Account Determination
< 10% Material valuation TSCM50, TSCM52, SAP210 SCM550
Price control TSCM50, TSCM52, SAP210 SCM550
Account determination TSCM50, TSCM52, SAP210 SCM550
Material Requirements Planning
< 10% Reorder point planning TSCM50, TSCM52, SAP210 SCM525
Lot-size calculation TSCM50, TSCM52, SAP210 SCM525
Planning run TSCM50, TSCM52, SAP210 SCM525
Planning result TSCM50, TSCM52, SAP210 SCM525
Logistics Invoice Verification
11-20% Invoices TSCM50, TSCM52, SAP210 SCM515
Credit memos TSCM50, TSCM52, SM001 SCM515
Automatic settlement TSCM50, TSCM52, SAP210 SCM515
Invoice verification in the background TSCM50, TSCM52, SAP210 SCM515
Adjustments TSCM50, TSCM52, SAP210 SCM515
Freight invoices TSCM50, TSCM52, SAP210 SCM515
Blocked invoices TSCM50, TSCM52, SAP210 SCM515
GR/IR clearing account maintenance TSCM50, TSCM52, SAP210 SCM515
Configuration of the Enterprise Structure and the Material Master
< 10% MM organizational levels TSCM50, TSCM52, SAP210 SCM550
Material type TSCM50, TSCM52, SAP210 SCM550
Field selection TSCM50, TSCM52, SAP210 SCM550
Solution Manager
< 10% Overview of the Solution Manager SM001
Experience from Implementation (Case Study or Project)
< 10% Integration and dependencies TSCM50, TSCM52, SM001 TSCM54
Design of enterprise structures TSCM50, TSCM52, SM001
Hope it will help you.
Thanks/Karthik

Trying Sony DCR-TRV16E as pass-through for VHS to iMovieHD5

Hello,
I've used the Sony DCR-TRV16E as pass-through for VHS to Nero 6 on a PC before without any problems, and Skype on the iBook running OSX 10.4.11 is happy with the camcorder showing the VHS tapes, but iMovie just tells me "Camera No Tape". I've tried to re-insert the FW cable several times and even played a few notes in GarageBand.
Was very happy when I managed to get the format DV-PAL instead of DV-NTSC, but since then I haven't progressed.
The setup is OK for the iBook and Skype, so what is the final magical touch that will enable iMovieHD5 with the iBook in my setup?
Thanks for your help.

Hello Matti,
For the first time in years, I tried to import analog using pass-through in my Panasonic NV-DS 38. iMovie 5 and 6 just says "no tape in camera" (in Swedish) and refuse tom import. iMovie 4 works just fine. The problem is that iMovie 4 runs in Rosetta on an Intel Mac. It seems as BTV/BTV Pro also runs in Rosetta (as the version is created way before any Intel Mac was available).
Do you know if there are any native Intel apps that captures DV?
(By the way, the tape mechanism in the Panasonic is broken, so I can't use the "playback tape" trick, where I suddenly stop the miniDV tape.)

Sequence settings for digibeta anamorphic capture?

I will be capturing from digibeta where the image is 16x9 anamorphic, using an AJA Kona card. What capture settings and sequence settings must I use to properly deal with the anamorphic image? I am renting the editing suite so I do not have access to it now. I need to prepare still images and titles using the same sequence settings that I will be using to capture. Does the Kona card come with sequence presets that I would not have in final cut pro 5.1, and if so can I edit my sequence settings to match?
Thanks,
Mike

The templates can be found in the new image settings, under "film and video" from memory.
But you could save yourself some trouble, and possibly aspect issues with an older version of Photoshop, by just making a new image in Photoshop that is 1024 x 480 (NTSC land).
Paste your images into that as your template.
Technically the images size IS 720x480 in your project, and then stretched out, but giving it 1024 x 480 starts you at a higher resolution, and avoids any graphics changing shape.
Though FCP handles larger images, and you would be fine to just have all stills under 2000 pixels, and resize in FCP.
Sure it needs to render, but then again you can do non-loss moves into stills.
Oh, and as for presets;
I prefer to use good old ProRes(HQ) rather then card specific codecs.
This way you can archive the project to a harddrive and later edit or change in a suite with a blackmagic card, or even a cardless machine(as in capture card!).
I believe there is an anamorphic Prores(HQ) anamorphic SD option,
or at the very least you can duplicate a Prores setting and tick the anamorphic option!
If you had the harddrive bandwidth and space you could choose to go uncompressed?
Digital beta is about 2:1 10bit, so close to ProRes(HQ).
Uncompressed is best though, but takes space and speed!
FC

Rounding value for direct procurement

Hi,
I an sourcing the same material from another plant within the same client. The materiale is some times purchased as a standard material using rounding value and going to stock. But, in some cases the material is procured as direct procurement. When purchasing for direct procurement will it then be possible not to use the rounding value but just order the exact quantity?
thanks,
Anders

Hi Andres,
I think, you do not need to take any action on this requirement. SAP works the way you wanted, by standard. For example, you have a setup with a vendor (may be via info record or material master itself may have rounding qty etc)...not a problem. The parameters you use in material master will control for procurement process either triggered from planning (or production ) or manual purchases. When you create a SO# and if it triggers a purchase requisition, it sends exact quantity required only, into the preqs. By standard SAP config, the message about rounding rules is just warning. I don't think you will be stuck with this message when you try to convert the 3rd party Preq to PO. Even if there is a message, it must just warning.
Let me know with these inputs, if you test both types of PO#s, how it goes.
Regards

PeopleSoft 8.52 Plug-in Implementation Guide for use with Grid Control

Per the Readme accompanying the download of PeopleSoft 8.52 Plug-in for use with Grid Control (11.1.0.1)-- "For the implementation reference guide, refer to "PeopleSoft Enterprise Environment Management Plug-in 8.52 for Oracle Enterprise Manager Implementation Guide" which you can download from Oracle Technology Network."
I don't seem able to find it.
Can anyone point me in the right direction?
TIA
Jeri

Duh, I was looking on the wrong site.

For direct activation of hierarchy, Aggregates have to be deactivated

Hi,
There are 2 monthly master data hierarchies loaded.
We face some problem while loading the hierarchies.
Now the 2 hierarchies are seen as Modified version.
When I try to activate the hierarchies manually I receive the below message
"For direct activation of hierarchy, 0042 Aggregates have to be deactivated"
with 2 options as:
1 Prebook activation
2 Activate directly
What are these options?
Will affect on aggregates?

hi,
Activate directly wlll directly activate the hierarchy....
Prebook for activation will capture it and it will be activated later at the time of the chnage run.
Always prefer Prebook for activation...
hope this helps.
regards,
Mahesh
Edited by: Mony Maheshsingh on Jun 24, 2010 4:22 PM

Use context to pass value between JPF and Java Control

hi,
Can we use context to pass value between JPF and Java Control? It works if i m using InitialContext in the same machine but i dun think it will works if i put Web server and application server in different machine. Anyone have an idea how to do it?
I also want to get the method name in the onAcquire callback method. Anyone knows how to do this?
thks
?:|

Hi.
Yoy can the next options for make this:
1. Pass your values in http request.
example: http://localhost/index.jsp?var1=value1&var2=value2&var3....
2. You can use a no visible frame (of height or width 0) and keep your variables and values there using Javascript, but of this form, single you will be able to check the values in the part client, not in the server. Of this form, the values of vars are not visible from the user in the navigation bar.
Greeting.

How can I asociate a DataSource to a Port for my Video Capture Card???

Hi!
First of all, I sorry for my bad english.
I'm trying to manage ports of my Video Capture Card.It's 4 ports. I believe I can manage it cause running this code I found in a web, I can see a panel called Video Source that contain all my capture devices (the capturer card too) and the four ports. Ports have been asociate like SVIDEO, TVTUNNER, COMPOSITE, COMPOSITE2. I'm trying use PortControl, but I don't ontain nothing. I'm learning java for around only three weeks, I don't know very much.
My question: How can I asociate a DataSource to a Port for my Video Capture Card and so manage 4 streamings data . Should I work Port Control over a medialocator, a datastream, a player...?
I'm looking forward your answers. I'm very sad cause this problem.
Thanx for advance!

xinixmayur, please don't post in threads that are long dead. When you have a question, start your own topic. Feel free to provide a link to an old post that may be relevant to your problem.
I'm locking this thread now.
db

Best Configuration for Multiple Video Captures

Hello,
What would be faster and the most efficient for multiple video captures:
- 9 video feeds written to 3 separate internal hard drives (3 feeds per hard drive)
- 9 video feeds written to 3 internal hard drives in a combined RAID configuration
- 9 video feeds written to 9 separate external hard drives via eSATA
I have a Mac Pro 3.06GHz 12-core Intel Xeon machine that will be dedicated to a security camera application (SecuritySpy). The Mac OS and SecuritySpy will be on one hard drive and send the captured video from nine network HD cameras to the other hard drives. The computer, eSATA card, and all the hard drives are 6Gb/s capable. I also have access to SoftRAID for the RAID configuration, as well as an 8-bay eSATA hard drive enclosure if I choose. There are pros and cons for each of the configurations, but I am looking for the most reliable setup in terms of efficiency and longevity.
“Technological change is like an axe in the hands of a pathological criminal.” (Albert Einstein, 1941),
Dr. Z.

Just wanted to post the details of my final set up, maybe this will be useful to others looking to do a similar setup:
1. Connected and set up the external hard drive (I bought a Western Digital My Book Pro Edition II 1TB) via Firewire 800 on iMac #1.
2. Set up iMac #1 to backup via Time Machine. Even though the other computers will see the drive, apparently they will not recognize it in Time Machine unless you set it up on the computer the drive is connected to first (I tried).
3. On iMac #2, connect to iMac #1 via file sharing, this is even easier now that you can access any computer on your network under "SHARED" in the sidebar of any finder window.
4. Double-click the external drive. If you don't see the drive, click "Connect as" in the top right of the window and login. It's not necessary to do this, but if you want to confirm you've connected to the network drive, you can go to Finder -> Preferences -> General and under "Show these items on the Desktop" check the box next to "Connected Servers". This will make an icon for the external drive appear on your desktop.
5. Turn on Time Machine on iMac #2. Repeat for any other computers you want to back up.
That's it. So far this has worked great for me. Obviously the backups run a little slower on the computers running through file share, but its a small trade-off compared to either manually moving the drive around or getting three separate drives.

UCCX Finesse silent monitoring for direct dial calls

I completely understand that Finesse is geared towards the inbound contact center, at least for right now. Although I can't say the marketing materials really stress that. But I cannot understand the lack of silent monitoring for all call types. Currently silent monitoring only works for inbound calls from UCCX, and does not function for direct inbound calls, or direct dialed outbound calls.
From a system view, Finesse is using UCM's built in silent monitoring, via a very basic JTAPI command. There is very little engineering required to enable this functionality, and I truly thing is is a major limiting issue. Many customers in fact only want the ability to do silent monitoring and basic reporting, and Finesse would be a perfect product for this.
I am considering looking at putting together some custom scripts/web apps to engage the required JTAPI in CUCM via a Finesse Gadget, to replace the built in Finesse silent monitoring function. I'm curious if anyone has some input on how involved that might be, seems like I just really need to pass the monitoring DN and monitored DN through a JTAPI command.
More importantly, is there any hope for Finesse to support this natively? Or other outbound features? If it's a feature "in the works" we have a customer who might be able to "get by" using the Cisco Agent Desktop silent monitoring, but only if that is the case.
Good link on silent monitoring capability in Cisco Finesse: http://www.cisco.com/c/en/us/products/collateral/customer-collaboration/unified-contact-center-express/white-paper-c11-730883.html

We've got to delimit the problem.
When we use 3rd party recording solution there are 4 RTP flows: 1 incoming to monitored/recorded phone and 3 flows outgoing.
1 incoming RTP flows
- voice of remote phone
3 outgoing RTP flows
- voice of monitored/recorded phone
- voice of monitored/recorded phone sent to 3d party recording server
- voice of remote phone sent to 3rd party recording server
When we use a network analyzer we see that the agent running in the PC (UCCX 5.0) establishes two RTP flows for the monitoring session. But we can see that one of these flows sends 3 packet RTP per 1 packet RTP sent in the other RTP flow (in the same time).
We think agent sends to monitoring device all the outoing RTP packets of the phone (that belong to three different RTP flows), instead of sending only the RTP packets belonging to voice of monitored/recorded phone.
The other flow, voice of remote phone, sounds fine.
Is there a solution to avoid this problem when we monitor with UCCX 5.0 and record with a 3rd party software at the same time?
Thanks,
Christian

Passing values for chekbox

Hi experts,
I have have hot spot for one field in o/p.
when i click that it leads to transaction fd32
in fd32 first screen contains credit control area,credit account and check boxes i had passed parameters for credit control area and credit accout reg checkboxes ihave to enable all the cheboxes and skip to second screen by default hw to enabele all the check boxes
when i keep fd32 in rec i am not getting second screen
to use bdc.
How can i eable all the check boxes?
Thanks,
shankar.

Hello Shankar,
I think for this requiremnt u have to go for BDC recording and call the Call the Transaction.
If useful reward.
Vasanth

By passing Kona for direct firewire capture/control

Similar Messages

Maybe you are looking for