C6180 Wireless Network Fax not Working

I have a Photosmart C6180 I can not send a fax from my notebook over the wireless network. I can print over the network. I can do a fax test over the network. I can send a fax manually. When I try to print to a fax I get a popup "Processinf fax request" but nothing ever happens.

Welcome to the Apple Forum.
Did you enaled the option that says "create a closed network"? Uncheck it if so.

Similar Messages

  • Wrt610n wireless network does not work after firmeware upgrade

    Hi
    I just updated my Wrt610n hardware version 1 to the newest firmware, it did finish with sucess, I did factory reset reboot and reconfig. But the wireless network does not work , cant connect computers to it. Did downgrade the firmware to the same it was and restore my settings but still wireless does not work. But router works fine with lan.  Any suggestions? maybe the firmware tosted the router?
    Regards
    Stefan

    Update -
    After last reset and reupgrade with the newest firmware for hardware version 1 I could config the router and connect 2 computers with wireless - but only for about 15 mín - then they lost connection and could not reconnect.
    I did then get the newest update for hardeware version 2 - just to try and upgraded with that and got success, and now I have reset the router again and config it and those 2 computers are connected and have been for 1 hour now. So seems to be working - is it okay to have the firmware for hardware version 2 on my version 1 router?
    Any thought what is going on - could it be that the other firmware had not loaded compleytle or?

  • Wireless network adaptor not working

    My wireless network stopped working, and the wireless network adaptor is not showing in the device manger.  The keyboard indicator indicated wifi disabled (f12).  Pushing then button does nothing. It was working fine earlier in the day.  The only change made was an adjustment to text size which required a restart to take affect.  The wireless adaptor did not work on the restart. Not sure what to try next to get it working again. Any advice would be appreciated. Thanks, 

    With two routers you'd have to put one of them into bridge mode. If the linksys is the second router then change its IP from 192.168.1.1 to 192.168.2.1
    You'll still have WPA issues with this configuration because the linksys really is not setup to handle bridge mode very well.

  • Wireless Networking does not work within Windows Vista

    I need to use Windows IE6 for work but when I open my Windows application, I cannot get my wireless networking to function. Diagnostics says I don't have a Network Adapter install. Back in the MAC O/S, the wireless networking functions fine.
    ???

    Resolved. Windows server 2008 r2 works cool secured. with Mavericks in MBP 2014. All are working well.
    Steps:
    Identify your mac book and related Boot camp version from Apple support and download.
    Integrate the drivers as mentioned in the below link.
    for install.wim follow the steps in the below link.
    for install.esd (this is the case with Windows server 2008 r2), convert install.esd to install.wim, integrate the drivers and convert back to install.esd and replace the original install.esd.
    Install Windows (7 or 8 or server 2008)
    After installation install additional drivers from Boot camp  - driver folder.
    For Windows, all should function (all are functioning for me).
    For server versions (all drivers are installed), you have to enable sound from device manager, enable wireless connection by adding additional features from Server manager, it works.
    For windows server 2012, integration is not required, it installs as is for MBP 2014, only wireless have to be enabled through server manager (remaining all worked fine)
    While installing the drivers, install Boot camp, to enhance additional features like track pad etc., (as in Mac OS)
    (Note:
    'install.wim' or 'install.esd' integration is needed to avoid hangout during installation - to enable track pad and keyboard
    intel folder) to $WinPEDriver$ folder to install chipset drivers, during OS installation. Chipset driver is not getting installed, when you install along with other drivers, gives out error.
    Enjoy Windows (any version) with Mac Book Pro.

  • [Solved] Wireless Networking Randomly Not Working

    Note: My network card is an Atheros AR9285 PCI-E Adapter. ath9k driver and wicd
    Apologies in advance, I'm relatively new to Linux as a whole. With the recent pacman 4 update, my entire system has been somewhat out of whack. I've been unable to figure out how to get it to properly sign keys and update packages, but that's another story entirely. At least my wireless connection still functioned when that was the problem.
    I booted my laptop up today and it was suddenly unable to connect to my wireless network. I checked the network to make sure that it was running properly (it is), so came back to the laptop. It said that it was unable to acquire an IP address.
    Various googling via my windows box led me to various suggested fixes including restarting wicd and wiping the .conf files, starting from scratch. All that accomplished was making the network hidden, and I'm afraid I've no idea as to how I probed it to show the SSID in the first place.
    Again, I'm very sorry, but this is extremely vexing for me, and I'm quite overcome by frustration at the moment. Everything was working fantastically until this pacman update, and now my laptop is good for very little.
    Last edited by Velshtein (2012-01-29 05:22:41)

    Thank you very much zero, I appreciate the help. Here's what I've got:
    For ip addr:
    1: lo: <LOOPBACK,UP,LOWER_UP> mtu 16436 qdisc noqueue state UNKNOWN
    link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
    inet 127.0.0.1/8 scope host lo
    inet6 ::1/128 scope host
    valid_lft forever preferred_lft forever
    2: eth0 <NO-CARRIER,BROADCAST,MULTICAST,UP> mtu 1500 qdisc pfifo_fast state DOWN qlen 1000
    link/ether f4:6d:04:a9:ec:d6 brd ff:ff:ff:ff:ff:ff
    3: wlan0: <NO-CARRIER,BROADCAST,MULTICAST,UP> mtu 1500 qdisc mq state DOWN qlen 1000
    link/ether 74:2f:68:1a:84:2e brd ff:ff:ff:ff:ff:ff
    Had to create a new wpa_supplicant to get your second set of directions to work, but work it eventually did. The output of dhcpcd looked a little something like this:
    dhcpcd[8282]: version 5.2.12 starting
    dhcpcd[8282]: wlan0: broadcasting for a lease
    dhcpcd[8282]: eth0: waiting for carrier
    dhcpcd[8282]: wlan0: offered 192.168.1.106 from 192.168.1.1
    dhcpcd[8282]: wlan0: acknowledged 192.168.1.106 from 192.168.1.1
    dhcpcd[8282]: wlan0: checking for 192.168.1.106
    dhcpcd[8282]: wlan0: hardware address 00:26:ab:00:9a:b1 claims 192.168.1.106
    (Lines 4-7 repeat twice more)
    dhcpcd[8282]: timed out
    dhcpcd[8282]: forked to background, child pid 8327
    ip route does nothing (visible anyway)
    Last edited by Velshtein (2012-01-27 03:21:39)

  • Upgraded to 10.4.10 and auto connect to last wireless network does not work

    Hi !
    just upgraded to 10.4.10 and now every time I boot I have to select my home wireless network to connect. This while I have the option automatic join selected, which worked until version 10.4.9.
    Anyone else experiencing this ?
    thanks for your time !

    Well, well,
    I downloaded the new Safari beta version and went (don't ask why, maybe insanity: doing the same thing over and over again, expecting a different result) to System Preferences->Network again. There I deleted my wireless network (as I did the last time), but now I got immediately a message about KeyChain (which I didn't got before, so I did get a different result !!). And guess what, now the auto connect does work again !
    So, the upgrade to 10.4.10 messed with something that the beta upgrade did correct.

  • IPhone 4S "could not scan for wireless networks" WIFI NOT WORKING?

    Ok, so I understand there is a million threads on this same issue... YOU'D think it would be fixed by now?
    What I don't understand is why the wifi isn't working?
    I just got the iPhone 4S yesterday, I already have an iPhone 4. The iPhone 4 is consistently using my home wifi while I am at home PERFECTLY. My iPhone 4 is updated to the latest software too iOS 5.1.
    My iPhone 4S will not connect to wifi. I am entering the right WPA user & pass. It is updated with iOS 5.1.
    My iPad, iMac, Macbookpro, & iPod ALL have NO TROUBLE connecting to my home wifi.
    I do not understand how this is a wireless router issue when it works with all of my other Apple devices BUT the iPhone4S?
    I have tried everything under the sun, restart reboot, turn off, turn on, switch network off, switch it on, reset this, reset that?
    PLEASE HELP ME! I have never been this disappointed in Apple (as you can tell I own everything by Apple, so I am quite the fan..)
    What the ****?

    Could this be the problem?
    iPhone 4 Modem Firmware : 3.0.04
    iPhone 4S Modem Firmware : 2.0.10
    Wifi is working on my iPhone 4, NOT on 4S -
    Why is my new 4S I got yesterday using a 2.0.10 firmware, isn't that old?! Isn't the newest 4.0+?
    I am so tired of trying to figure this out.
    The Wi-Fi addresses in the About settings are different on both phones too.

  • Windows wireless network would not work straight away upon encountering a new network.

    A Windows 8.1 network always works in a home environment.  When taken to a public library, the network itself works but wouldn't connect to the Internet.  After a lot of fiddling, changing user, restarting the computer and so on, all of a sudden
    it starts to work.  Windows diagnostic does not detect any problem.  When it comes back home, it works straight away without any drama.
    When the problem happens with a public network, the Windows diagnostic and ipconfig reports no ip address has been assigned to the computer.  So I think perhaps the network runs out of IP address to be assigned.  Then I use a mobile phone which
    connects to the library network and hence the Internet to set up tethering and portable hotspot and test the computer again.  Again the computer has no problem with the network but wouldn't connect to the Internet.
    I think to myself, if it is a hardware problem then it would not even work at home.  If it is an intermittent hardware problem, then such problem should be experienced at home as well.  But no, nothing happens at home so far.  Could anything
    peculiar to Windows 8 that causes such phenomenon?

    You can try the Orangeware driver, but according to this website it looks like it isn't going to work.
    You are going to need to sell/return the card and get a different one that works.
    iFelix

  • Wireless Network Does Not Work After Coming Out of Sleep

    I have a WEP connection that does not broadcast. My Airport connects to it fine. When the MacBook comes out of sleep mode, sometimes it cannot connect and does not show the network in the list of available networks (because it doesn't broadcast, but the network is setup so it should show). If I turn off Airport and then immediately turn it back on, it connects right away.
    Has anyone else had this problem? Does anyone know of a fix?

    Thanks for the reply. I don't think I need to delete and recreate the connection because just bouncing the Airport on the MacBook brings the connection back online... so I don't think there is anything wrong with the connection per se. It doesn't happen every time I come backup from sleep, just often enough that it's something I'd like to see them fix in an update if it's a problem that other people are having too.
    As for switching from WEP, I have a many wireless clients in my house including laptops, desktops, printers, console systems, and iPhones/Smart-Phones. They all support WEP, but they don't all support WPA. I'd rather try to keep from buying new network cards or new printers.

  • Photosmart C6180 on wireless network does not respond when attempting to print

    Photosmart C6180 successfully installed on wireless network does not respond when attempting to print.  All in one is successfully installed on wireless network and SW successfully installed on Windows XP computer yet printer does not print.  Get no error message other than document failed to print.  HELP!

    So gald I'm not the only one. I have been fighting this crappy HP printer for MONTHS also. Everything says a OK goody goody but printer fails to print every two to three weeks.

  • I have my HP OfficeJet Pro 8500 A connected to my Mac Book Pro on a Wireless network. It works and

    I have my Hp Officejet Pro 8500 A connected to my MAc Book Pro which is running Lion OS on a wireless network.  It works just fine and prints and everything.  The problem is a "HP Utility" window that pops up on my screen and says it is "connecting to device" and lists my printer.  It just runs and runs and the entire thing is gray - meaning I can't close it, cancel it, or anything. When you try to click on it, the arrow becomes the color wheel of death.   It is driving me crazy.  I have gone through settings, I have downloaded the latest drivers, I have looked in utilities, I have opened the printer folder and can't find where this thing is coming from or how to turn it off.  Please help.  And yes I have turned offf the computer and rebooted.  

    If you are using Snow Leopard or Lion and have HP software for pre-Snow Leopard (either from a CD not marked as compatible with 10.6 or you recently upgraded to Snow Leopard or Lion and had the HP software on your Mac before you upgraded - even if you did a standard uninstall of the old software or installed new software over the top of it) you must uninstall the software using the 'scrubber' option:
    Go to Applications/Hewlett Packard/ click on HP Uninstaller
    Click on Continue
    Highlight your device on the left pane
    Press and hold Control + Alt + Cmd keys on the keyboard simultaneously while you click on Uninstall <<<< This IS the Scrubber Option, there is no button labeled "Scrubber"
    There will be a pop up that asks if you are sure you want to uninstall ALL hp software. (At this point, if you continue, any HP printers you have installed will need to be reinstalled)
    Click Continue and let it finish
    Restart your Mac
    Download and install this: http://support.apple.com/kb/DL907
    Now reset the printing system:
    - Sys Prefs, Print & Fax
    - Right (control) click in the rectangle listing your printers and select Reset Printing System.
    WARNING - this will delete ALL of your printers!
    - Select the plus sign to re-add it. Look for the printer, select it and wait until the "Add" button becomes available. Click it.
    If you want more features, you can download and install the Full Featured software from the "Support & Drivers" button at the top of this page, otherwise, basic printing and scanning will work without it.
    Say thanks by clicking "Kudos" "thumbs up" in the post that helped you.
    I am employed by HP

  • I have a Linksys WRV200 wireless router and the wireless signal is not working properly so I cannot connect to the internet wirelessly. the wireless light has a fast green blinking light. how can I fix the router?

    I have a Linksys WRV200 wireless router and the wireless signal is not working properly so I am unable to connect to the internet wirelessly.  The wireless light is blinking green very quickly and I connect and disconnect from the network constantly.  How do I get the router to work properly

    Hello James,
    The flashing WLAN light means activity (data getting transferred). Try disconnecting all your devices and check whether the light is still flashing or disconnect the router from internet and do the check.
    Do you have your SSID as linksys or the default one? If your neighbor has the same SSID, then traffic could result from your neighbor's one. Try changing your SSID and password. Make your security WPA/WPA2.
    Hope this helps,
    Thanks
    Vijay

  • Laser Jet M1217nfwMF​P wireless and fax stopped working printer works with usb cord

    I have an HP computer 64 bit version.  The printer suddenly stopped working wireless, fax stopped working weeks ago.  Printer does work with a usb cord.  Turning it off (removing elec cord) on both computer and printer, didn't help.  Nothing changed that was different to cause either problem.

    Hi agueda
    I see that your Laserjet M1217 wireless and fax stopped working but the usb connection does work.
    I would restore the printers defaults to setup the wireless again.
    Touch the setup (wrench button) on the printer, select network config, select restore defaults.
    Then make sure the wireless radio is turned on.
    Touch the setup button (wrench), network configuration, wireless menu, wireless radio-on.
    Temporarily connect the usb cable from the printer to the computer and go to start, all programs, hp, laserjet m1217 and select wireless configuration and go through the wizard to reset up the wireless again.
    or if your router has a wps button on it then you touch the wps wireless button on the printer and immediately touch the wps button on the router.
    Printer should automatically connect to the wireless network.
    Run the add printer wizard.
    Go to control panel,(win7) devices and printers then click add a printer, next, select network
    highlight printer, next, message installing printer.
    Should be able to print over  wireless again.
    Check  fax connections.
    Then run a fax test.
    Touch the setup (wrench button) on the printer, service, run fax test.
    You should have 4 passes.
    Change these fax settings on the printer.
    private receive-wrench/fax setup menu/ok/fax receive setup/ok/private receive/ok/set it to off
    error correction-wrench/arrow to fax setup/ok/all faxes/error correction/ok/set it to off/ok
    speed-wrench/arrow to fax setup/ok/all faxes/ok/fax speed/ok//change speed to medium.
    clear saved faxes-wrench/fax functions menu/clear saved faxes/ok/ok to clear.
    Try sending and receiving a fax.
    If you have any further issues please let me know.
    Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
    Click the “Kudos Thumbs Up" on the right to say “Thanks” for helping!
    Gemini02
    I work on behalf of HP

  • So my airport extreme recently had some nat/dns issue and in the airport utility displayed a warning about it and to correct it. I wasn't sure what to do so i pressed the resolve icon and now my guest network is not working.

    So my airport extreme recently had some nat/dns issue and in the airport utility displayed a warning about it and to correct it. I wasn't sure what to do so i pressed the resolve icon and now my guest network is not working.

    Anytime you change networking hardware, it is always a good idea to perform a complete power recycle of your networking components.
    I would recommend that you do the following as a minimum:
    Power-down the modem, AirPort base station, and computer(s).
    Disconnect the AirPort base station from the Internet broadband modem.
    While all of the devices are powered-down, perform a "factory default" reset on the base station. This will get it back to its "out-of-the-box" configuration and make setting it up much easier, especially if you use the "Assist me" process within the AirPort Utility. (ref: Resetting an AirPort Base Station or Time Capsule)
    After the base station resets, go ahead and power it back down.
    Reconnect the AirPort base station to the Internet broadband modem. For the Extreme and Time Capsule, be sure to connect the cable to the base station's WAN (circle-of-dots) port.
    Power-up the modem; wait at least 10-15 minutes to allow it adequate time to initialize.
    Power-up the AirPort base station; wait at least 5-10 minutes. Note: The AirPort's status light may continue to flash amber after it has intialized. That is because, there may be some additional configuration items necessary, like setting up wireless security, before the overall setup is completed to get a green status.
    Power-up your computer(s).
    In this basic configuration, the AirPort base station will broadcast an unsecured wireless network with a Network Name (SSID) of Apple Network NNNNNN. Network clients, connected to the base station either by wire or wireless, should now be able to access the Internet through the ISP's modem. Once Internet connectivity has been verified, you can use the AirPort Utility to configure the base station for wireless security and any other desired options. Please post back your results.

  • Satellite A660 - Broadcom internal wireless adaptor is not working

    Hi all,
    My first post to this board - I have a new Toshiba Satellite A660 notebook - have only had it for about 4 weeks and it has turned out to be a disaster for me...
    FIRST - I spend weeks getting everything on and configured the way I want it - then the hard disk starts to die...
    I just got it back from the Toshiba service centre and NOW the wifi has stopped working...
    The internal broadcom wireless adaptor is not working - but according to windows and the built in diagnostics it IS working...
    HOWEVER - when I try to use wireless with the built in adaptor it can't detect any wireless networks...
    I then plug in my backup usb netgear wireless adaptor and I can pick up and connect to both of my home wireless networks...
    I am going overseas in a few weeks and need to know that my notebook is going to work/be reliable and not have any more problems - if anyone can help me with this it would be much appreciated.
    John.

    A further update for you all...
    Okay - went back to the Toshiba service centre - the first dead hard disk was replaced by them - but the REAL problem not spotted - it looks like my laptop came out of the Toshiba factory with a faulty motherboard - this in turn has now fried the second hard drive - and now - with a new motherboard and THIRD hard drive it looks like the hardware side of things MIGHT just be solved - but NOW I still have the problem that because the motherboard has been screwed since day one (I only bought this laptop in November 2010) it has basically stuffed/corrupted all of my backups - so now the service centre is charging me 60 dollars to get a set of disks so I can re-image the system myself when I have the chance - and then spend a month putting back all the applications and configuration and data the way I had it after the first few weeks of buying it (at that stage I thought I was good to go and had the perfect new laptop and setup for work...)
    So - I'm heading off overseas in a couple of weeks - my 3 year extended warranty from Australia will not be of any use to me where I am going - not covered - but am STILL hopeful that I'll get the rest of the problems sorted - still can't run the toshiba hdd protection software for more than a few days without it dying and having to be reinstalled and the toshiba pc health monitor does not work at all - when I go to install it it doesn't recognize the bios or whatever - and on top of that I'm using third party hard disk monitoring software (because the toshiba stuff doesn't work on this toshiba laptop - but the third party stuff does) - well, anyway - the third party software is telling me the hard disk has reallocated sectors count error - and there is a CAUTION showing all the time - which I guess indicates that there is now a hard drive problem with the third hard disk (?)
    Anyway - if ANYONE has had a similar run of bad luck to mine with the A660/O7U - I'd really like to know...
    John.

Maybe you are looking for