Call Blocking Based on ANI in a CUBE, Not Working.

Hello all,
So I have read the Docs I have found regarding blocking incoming numbers at the CUBE level. I have configured this and my calls are not getting blocked. I must be doing something wrong or maybe it is that I have more than one Translation rule on the dial peer. Here is the config, please let me know what you think.
voice translation-rule 1
rule 1 /^$..........$$/ /+1\1/
voice translation-rule 400
rule 1 reject /610XXXXXXX/
rule 2 reject /215XXXXXXX/
voice translation-profile BLOCK
translate calling 400
voice translation-profile PSTNin
translate calling 1
dial-peer voice 297 voip
description Incoming Telephone Numbers
translation-profile outgoing PSTNin
call-block translation-profile incoming BLOCK
call-block disconnect-cause incoming call-reject
preference 3
destination-pattern ^[2-9]..[2-9]......$
session protocol sipv2
session target ipv4:192.168.186.11
incoming called-number .
voice-class codec 1
dtmf-relay rtp-nte
no vad
dial-peer voice 298 voip
description Incoming Telephone Numbers
translation-profile outgoing PSTNin
call-block translation-profile incoming BLOCK
call-block disconnect-cause incoming call-reject
preference 2
destination-pattern ^[2-9]..[2-9]......$
session protocol sipv2
session target ipv4:192.168.186.12
incoming called-number .
voice-class codec 1
dtmf-relay rtp-nte
no vad
dial-peer voice 299 voip
description Incoming Telephone Numbers
translation-profile outgoing PSTNin
call-block translation-profile incoming BLOCK
call-block disconnect-cause incoming call-reject
preference 1
destination-pattern ^[2-9]..[2-9]......$
session protocol sipv2
session target ipv4:172.18.12.100
incoming called-number .
voice-class codec 1
dtmf-relay rtp-nte
no vad
I have verified I am hitting the correct peer on the inbound call but it looks like the translation rule 1 translation-profile outgoing PSTNin is adding the +1 which I believe is causing it to not match.
Any help would be great.

Kirill thanks for the response. I only used the X here to hide the numbers. They are not in the config. Additionally what you are saying about the +1 makes sense however the router will not take /+1610XXXXXXX/.
Is there a different method that would need to be used?

Similar Messages

After I've upgraded my iPhone iOS to 5.0.1, I got problems with connectivity. If my iPhone lose network, then it gets frozzen and I cannot make calls. After restart the telephone still does not work.

After I've upgraded my iPhone iOS to 5.0.1, I got problems with connectivity. If my iPhone lose network, then it gets frozzen and I cannot make calls. After restart the telephone still does not work.

1. Download the iOS 5.0.1: http://www.tobias-hartmann.net/2011/11/download-ios-5-0-1-veroffentlicht-direkte -downloadlinks/
2. open itunes,Click in iTunes while holding down the Shift key (on Windows) or Alt key (Mac) to restore and firmware

I have a 4s with ios 6 but when I place a call I can't hear the person I' m calling, the volume is high but it's not working. Please help.

I have a 4s with ios 6 but when I place a call I can't hear the person I' m calling, the volume is high but it's not working. Please help.

I have taken it back to the Apple store genius bar, but they say they don't see anything wrong. Well unless you use it all day and experience the problems when they happen, you wont see anything wrong. But there are lots wrong with it. But this would be the same store as I purchased the phone. And they backed up my old Iphone 4, but were not able to get anything to load back onto my new phone. So, I lost pretty much everything. But over time, some of my contacts have started showing up, although i am still missing over 800 of them.

Content Filter block attachment .scr/.cab etc... not working inside archive

Hi,
We have trouble that Content Filter for blocking attachments executable, scr, and cab is not working if .exe, .scr, or.cab are inside 7zip, zip or rar archive.
How deep inside attachment ESA goes, if any?
Antivirus config is set to 5 and some viruses passed like CryptoWall as .scr and .cab.
So, we are blocking that extension but this time they were inside archive.

Hello Juraj,
I apologise for the inconvenience.
Currently if there are viral definitions within the attachment, the AV engine would be the first line of defence, if you for some reason notice some viral attachments bypassing your ESA, please open a TAC case so we can escalate the sample to Sophos for you to capture.
As per content filtering.
The scan depth on how deep it will go into a system is defined in 'scanconfig' in the CLI.
This will show your current recursion depth.
As per .cab and .7z attachments not being properly captured if .scr or .exe are inside it
Currently there are some Enh request to allow the unpacking/decompression of these archive files to capture things inside it, at the moment the request is still undergoing review.
As a temporary measure you can proactively send .7z and .cab files to the quarantine for your administrative review --
The ESA will however be able to seek the executable should it be shrouded inside the .rar/.gzip and .zip archives however.
I hope this helps.
Regards,
Matthew

TS2799 call of duty world at war zombies does not work

I had purchased this game yesterday and it will not start

Note that the current version of Call of Duty World at War: Zombies does not work on the new iOS 4.2.1 - it crashes each time. This is due to the intro video. I have a support call logged with Activision on this but they don't seem to be to bothered hence why I will ask for a refund and not bother with their products going forward.

Using FORMAT_STRING from SSAS cube - not working consistently

Here's the deal.
I've got an SSAS cube and I am scoping the format of the measures based on dimension members.
Like this.
scope(( [Account].[Level 5].&[I000900000] ));
format_string(This) = "(#,0,);#,0,";
end scope;
I'm then calling this format in the SSRS report using typical SSRS trickery and hacks.
Well. When I run the report for one date (this is a GL financial cube), this works perfectly. When I run the report for a different date, it all of a sudden doesn't work. When I view the data in excel through a pivot table, everything is fine.
It's driving me crazy. Has anyone else experienced something like this.

Hi Baracus,
Thank you for your question.
I am trying to involve someone more familiar with this topic for a further look at this issue. Sometime delay might be expected from the job transferring. Your patience is greatly appreciated.
Thank you for your understanding and support.
Regards,
Charlie Liao
TechNet Community Support

Display has white and grey lines and blocks crisscrossing it and touch functions are not working properly on half the screen.

I dropped my iPhone 5S and it landed flat on it's face (it was in a protective case). Since then my touch screen display is not working properly. I have white and grey lines and/or blocks crisscrossing the screen both horizontally and vertically. Screen responds to touch in odd random ways, but rarely does what I am trying to do. Can't call or receive calls because can't dial or answer phone via swipe. Can't text or read incoming texts. All functions seem to be working except that I can't access them because the touch screen is acting up. If I move the phone around it randomly accesses different apps or functions, but I have no control over them once the appear on the screen. Touching screen just causes phone to randomly choose something else to open. What have I damaged?

Shanegang77 wrote:
What have I damaged?
We cannot possibly tell. Obviously some hardware inside. Take it in to an Apple Store. They will offer you the opportunity to swap the phone for $269 in the US. Prices vary by country.

When I cancel a call or don't answer the touch is not working

When I cancel a call or don't answer the touch is not working

To mute: Press vloume down button.
To disconnect: Press display off and on button on top.
Delete messages from Inbox: Click "Edit" button on top left and select the messages you want to delete.

Blocked Senders feature in Outlook 2010 does not work

I have a specific blocked sender
[email protected] listed in my Blocked Senders list, but emails from that email
address still go to my Inbox instead of the Junk E-mail folder.
We use Exchange for email, and Outlook 2010 as the client.
Note: this sender is blocked for a specific sender that he configured through Junk E-mail Options in Outlook 2010, and this sender is not blocked at the server level.
I only have one account set up in Outlook.
What do I need to do to get Blocked Senders / Junk E-mail working in Outlook?
Thanks,
Elizabeth

Hi,
From your description, I suggest you try to check the total size of blocked sender list. As total size of all lists combined cannot exceed 512K. Once the 512K limit
is reached, Outlook alerts you and additional addresses aren't saved until you remove some from the list.
If your issue is caused by the limited size, you can add a new registry key value to the following registry key:
HKEY_LOCAL_MACHINE\System\CurrentControlSet\Services\MSExchangeIS\ParametersSystem\
Add a new DWORD value of Type Max Extended Rule Size and edit the Value Data, entering the maximum size (in bytes) you want to allow.
If your issue is not related to limited size, try to keep your junk e-mail filter updated. Each version of Microsoft Outlook that contains a junk e-mail filter receives updates to the data
file (outlfltr.dat) as part of the Microsoft-wide monthly update released on the second Tuesday of each month. The updated outlfltr.dat is the result of the evaluation of hundreds of thousands of spam messages and constantly increases the filter “catch”
rate for incoming junk email.
The recommended way to obtain updates to the Outlook Junk E-mail filter is by turning on the Automatic Updates option in the Windows Security Center.
If you have done all above but it still not work, try to create a new outlook profile to test this issue.
Go to Start > Control Panel, click Mail. The title bar of the Mail Setup dialog box contains the name of the current profile. To select a different
existing profile, click Show Profiles, select the profile name, and then click Properties.
Click Show Profiles. Choose Prompt for a profile to be used.
Click Add.
Type a name for the profile, and then click OK.
Start Outlook, and choose this new profile.
Sincerely,
Harry

Populating called block based on criteria from previous block

i have a form where the query is based on the zipcode provided. I have a button within block a that calls another block b to display all records with that particular zipcode. I want the display on block b to show only the records for the specified zipcode. Please help and tell me how do I make this happen?

- In the WHERE-Clause-property of block b enter :
:BLOCK_A.ZIP_CODE
- Put a button next to Zip-Code of Block a
in the WHEN-BUTTON-PRESSED trigger enter :
GO_BLOCK('BLOCK B');
EXECUTE_QUERY;
Another option would be to use a relation between both blocks ...

Call blocking based on called number

Hi all experts.
In CUCM 8 or CME 4.x/7.x, is it possible to block calls coming from (PSTN) with the following prefix
+92 21 0345xxxxxxx
Let me explain the scenario which is very simple.
1) ITSP will be providing us sip trunk (30 channels)
2) SIP trunk will be terminated on 3845 router (running cme 7.1)
3) This router will be connected to CUCM 8.0 over SIP trunk (pls let me know if choosing h323 here makes any difference)
So now all the calls coming from ITSP shall be forwarded to CUCM. Is there anyway i can block the above prefix, so that any call coming from
+92-21-0345xxxxxxx is blocked and is not able to reach any extension in our organization.
I wanted to know if we can block this prefix on CME or CUCM or both ?
If its possible, pls explain it to me a bit and also refer me any cisco doc for further reference.
Thanks alot in advance

Hi,
You can do that with voice translation rules.
Here is a good example on how doing that: http://www.blindhog.net/using-voice-translation-rules-to-block-numbers/
Information about voice translation rules: http://www.cisco.com/en/US/tech/tk652/tk90/technologies_configuration_example09186a00803f818a.shtml
Gabriel

Maintain Cube Not Working

Brijesh,
I built my dimensions, levels and heirarchies successfully and also created cube. Now that I've built my measures and run the maintainance, I'm not seeing any values in them even though I know I should.
Based on my mapping, the keys from the fact are going to the right dimensions (and I even made a simplier, just one dimension --> measure cube as well), but no success. There are cases where I know I shouldn't get any data (based on selected values), but when I make valid selection I see only 0.00 being displayed.
Can you tell where I may have gone wrong here? Are the values made available for selection (the attributes) ONLY supposed to be the same one-to-one values available in the fact table?
**I'm using the simple SUM aggregate function for my measures, and pretty much all the default configurations given.
Brijesh Gaur
Posts: 416
Registered: 04/03/08
Re: where are dimension attributes in AWM - cube viewer?
Posted: Nov 10, 2009 3:21 AM in response to: mikeyp Reply
Attribute is something related to dimension. They are purely the property of the dimension and not the fact. Now you said the data is not visible in the cube and you are getting 0.00 even with a simplier case(one dimensional cube). There are many causes of the value not shown in the cube and some are mentioned below
1. All records are rejcted in the cube maintaince process. For this you can check olapsys.xml_log_log table and see if you can find any rejected records.
2. There is some breakage in the hierarchy of the dimension. It also prevents data from summing up.
Did you tried with the global sample available on OTN? That should be good starting point for you.
You can check the cube as below to find out it is loaded or not. Consider your one dimensional cube. Find out a member which is existing in the dimension and also has some fact value associated with it.
1. Now limit your dimension to that value like this
lmt <dim name> to '<value>'
For compressed composite cube
2. Now check data in the cube like this
rpr cubename_prt_topvar
for uncompressed cube you should do
rpr cubename_stored
#2 should show the same value which is available in the fact.
Thanks,
Brijesh
mikeyp
Posts: 14
Registered: 09/22/09
Re: where are dimension attributes in AWM - cube viewer?
Posted: Nov 13, 2009 1:24 PM in response to: Brijesh Gaur Edit Reply
Brijesh,
Thanks for your suggestions, and here are my results based on that.
1. No records rejected after running cube maintenance
2. I didn't limit my dimension to specific value as you recommended, but made my member the same as my Long and Short description attributes using AWM. (Its a flat dimension i.e. no level or hierarchy since the dimension only has one value/meaningful field.
Based on those steps, I still didn't get the results I was looking for. The fact table has five values for that one dimension and I'm seeing 0.00 for 4 of them, and an inaccurate value for the last one. (this after doing comparison with simple aggregate query against fact)
Do you have any other possible reasons/solutions?
**Loading the Global Schema into our dev environment is out of my hands unfortunately, so that's the reason for the prolonged learning curve.

Brijesh,
Here's the results of what you suggested:
1. Creating test dim and fact table with simple case you provided was successful, and AWM was able to map the same values to cube which was created on top of that model.
2. I took it a step further and changed dim values to be same like existing dim table
2.b. Also replaced test fact table values to mimic existing values as well so it would match what's available in dim table, and here's where the fun / mystery begins
Scenario 1:
I created fact like this...........select dim value, sum(msr) from <existing fact table>
As you can easily tell, my values were already aggregated in the table, and they also match perfectly in cube created by AWM - no issue.
Scenario 2:
Created fact like this............select dim value, msr from <existing fact table>
Quite clear is that my values are no longer aggregated, and broken down across multiple occurences of dim values; did this so that I can verify that the "sum" will actually work when used in AWM.
The results from scenario 2 lead me back to same issue being faced before - i.e. the values weren't being rolled up when the cube was created. No records were rejected, and there was only ONE measure value showing up (and it was still incorrect), and everything else was 0.00
I retrieved this error from the command program that runs in the background. This was generated right after running the maintain cube:
<the system time> TRACE: In oracle.dss.metadataManager.............MDMMetadataProviderImpl92::..........MetadataProvider is created
<the system time> PROBLEM: In oracle.dss.metadataManager.........MDMMetadataProviderImpl92::fillOlapObjectModel: Unable to retrieve AW metadata. Reason ORA-942
BI Beans Graph version [3.2.3.0.28]
<the system time> PROBLEM: In oracle.dss.graph.GraphControllerAdapter::public void perspectiveEvent( TDGEvent event ): inappropriate data: partial data is null
<the system time> PROBLEM: In oracle.dss.graph.BILableLayout::logTruncatedError: legend text truncated
Please tell me this helps shed some light on the main reason for no values coming back; we really need to move forward with using Oracle cubes where we are.
Thanks
Mike

Continuity Bluetooth Calling & SMS on Macbook Pro (via iPhone 5) Not Working

Devices:
Macbook Pro Mid-2010 running OSX 10.10.2
Iphone 5 running iOS 8.1.3
*NOTE: I understand that due to the version of the Bluetooth protocol in my machine, not all continuity features are available (Handoff, Air Drop, MBP Instant Hotspot)
However SMS to IMessage and the ability to make and receive calls from my Mac should be OK according to Apple's system requirements one-sheeter:
System requirements for Continuity on iPhone, iPad, iPod touch, and Mac - Apple Support
================================================================================ =====================
Here's my problem.
I finally took the plunge last night and updated my iPhone 5 from 7.1 to 8.1.3 to access the iCloud Drive and additional continuity features integrated into Yosemite.
When I tried to pair my iPhone 5 with my MBP over Bluetooth, all seemed to go well for the first 5 seconds.
- Both devices were in discovery mode.
- Mac saw the phone and displayed a security code
- iPhone displayed the same security code and asked if I would like to pair with MBP
- Pairing took place. Each devices Bluetooth profile / device showed up in my MBP Bluetooth's Preferences and in my iPhone's Bluetooth.
- 5 seconds later, there's no connection between devices.
My iPhone displays:
"Connection Unsuccessful: Make sure [Macbook Pro] is turned on and in range." (The phone is 5 inches away)
Then sometimes I get this message:
"Connection Unsuccessful: [Macbook Pro] is not supported.
No rhyme or reason between the two either.
Here's the baffling part: When I activate my Phone's HotSpot function, the Bluetooth works and connects with my MBP allowing it to use my cell phone network's data for internet connectivity.
I don't understand what is going on or how to correct this? Can anyone succinctly explain how to correct this problems in layman terms?
If the devices can communicate long enough to exchange security codes and verify their identities, then use Hotspot, there is clearly a data exchange happening. Where is the break down taking place when it comes time to stay connected to so I can continue to use the limited continuity features.
I've seen this question posted before by people having problems with different model years of MBP including the most recents models, so I know it's not mutually exclusive to my model year, but cannot seem to find clarity on an answer.

Handoff Continuity Troubleshooting
iPhone, iPad, iPod touch, and Mac using Continuity - Connect

Delete overlapping requests from cube not working in processchain.

In a process chain, 'deletion of overlapping requests from the cube ' step is used.
Before this step a DTP step runs with a full update to load the cube. This process chain is scheduled every day.
Issue is, the process chain failed at the DTP step and after correcting and repeating, the step got executed.
However, the next step after the DTP,'delete overlapping requests from the cube'
gets executed but without deleting the previous day's request.
In the step details a message that 'No request for deletion were found' can be seen.
Then next day when the DTPstep is executed without any problem the 'delete overlapping requests from cube' step is successful
and the previous requests from cube are deleted.
the deletion selections in the step ' delete overlapping request from infocube' is
Delete existing requests
Conditions:
only delete requests from same DTP
Selections
Same or more comprehensive
Because of this issue on a particular day because of the presence of 2 days requests the data is getting aggregated and shown as double in the reports.
Please help.

Hi Archana,
When you delete the bad request from target and before repeating your DTP in PC, make sure the bad request deleted from table RSBKREQUEST also.
If you find the same request in table, first delete the request from table and repeat the DTP in PC.
Now Delete overlapping step should work.
As this is not the permanent solution, please raise an OSS for SAP
Regards,
Venkatesh

Blocking Ad servers via etc/host file not working

In Snow Leopard I add a list of ad servers and direct them to 127.0.0.1 via the /ect/host file.
I've configured the host file on my mac mini server and it doesn't work.
i just want to block ads when using browsers ON the Mini.
How can I achieve this?

Yeah; that's an old-time Windows and Unix hack.
There are ad-blocking extensions for all major web browsers, and those are easier to manage and maintain.
Off the top, I'd have to check the search order to see if I was getting a response from remote DNS or from /etc/hosts here.
If you're running a Mac OS X Server box, you're hopefully also running DNS services, and if you're running DNS services, then that's going to be where this hackery gets implemented. Add bogus zones. And if DNS gets an answer from its cache, I wouldn't tend to expect it to go read /etc/hosts (for performance reasons), for that matter.
There may well be an ad-blocking DNS server around you can forward queries to, too; I haven't looked for that.
If you make changes to your local /etc/hosts setup, try issuing the following to clear the cache:
dnscacheutil -flushcache
I'd recommend installing an ad-blocker. /etc/hosts is an old-school approach and can end up causing weirdnesses on errors, particularly if your box is (also) a DNS server for your LAN. (Also realize that Apple isn't documenting the /etc/hosts file in the Mac OS X Server 10.6 networking manual.)

Call Blocking Based on ANI in a CUBE, Not Working.

Similar Messages

Maybe you are looking for