CALL DOES NOT ROUTE OUT THE LOCAL GATEWAY

Local calls will not route out the local Gateway of branch1 to the PSTN or from the PSTN back to branch1, however they will route out either CorpHQ or branch2 backup gateways. When I go into the route group configuration for branch1, and remove the backup gateways, I get a fast busy tone when I dial the local number. I know the MGCP Gateway at branch1 is functioning because when I dial 911 and run debug ISDN Q931, the call routes properly through branch1, so I have a call routing problem. I ran DNA and it came back as ROUTE THIS PATTERN and all of the number translations looked accurate, so I didn't have to check for any block patterns. I'm not getting any errors on the calling party phone display. When I deleted the route pattern for the branch1 site and forced it to use the global route pattern, I received a debug output on branch1. I do not know a debug command (such as debug voip dial-peer or debug ccsip messages) to use for an MGCP Gateway to see if the call is actually reaching the Gateway.
I have checked the following:
the route pattern configuration
the translation pattern configuration
the called party transformation pattern configuration
the route list configuration to make sure the correct route group for branch1 was selected
the route group configuration to make sure that the branch1 Gateway was first in the order of selected devices
the route pattern configuration to make sure the correct route list for branch1 ist selected
the Gateway configuration to make sure it's using the device pool for branch1 and to make sure the called party transformation CSS for the branch1 Gateway is applied
the device pool configuration to make sure it's using the route group branch1
Any assistance would be greatly appreciated
Regards,
Ron

Hi Nishant:
Please see the attachments for the Gateway pages
The significant digits for inbound calls for all 3 gateways is '4'
Please see the running-configs of the 3 gateways and the PSTN
Please see the debugs for the INBOUND calls
Many Thanks,
Ron
The following INBOUND call from the PSTN to 2065011001 is now working, however it is supposed to be routing through CorpHQ and is instead routing through Branch1. Please see 'DEBUG VOIP CCAPI INOUT' & 'DEBUG ISDN Q931'
Branch1#
ISDN Se0/0/0:23 Q931: RX <- DISCONNECT pd = 8 callref = 0x0096
        Cause i = 0x8290 - Normal call clearing
//22/xxxxxxxxxxxx/CCAPI/ccCallReportDigits:
   (callID=0x16, digit_event=0x0, enable=FALSE, consume=FALSE)
//22/5A001212800B/CCAPI/ccCallReportDigits:
   Enabled=TRUE, Call Id=22
//22/xxxxxxxxxxxx/CCAPI/cc_api_call_report_digits_done:
   (vdbPtr=0x49E07FD4, callID=0x16, disp=0, digit_event=0x0, enable=FALSE, consume=FALSE)
//22/5A001212800B/CCAPI/cc_api_call_report_digits_done:
   Enabled=TRUE, Disposition=0x0, Interface=0x49E07FD4, Call Id=22
//22/5A001212800B/CCAPI/cc_api_call_report_digits_done:
   Call Entry(Initial Digit Timeout=4000(ms), Inter Digit Timeout=4000(ms))
//22/5A001212800B/CCAPI/ccGenerateToneInfo:
   Stop Tone On Digit=FALSE, Tone=Null,
   Tone Direction=Network, Params=0x0, Call Id=22
//23/5A001212800B/CCAPI/ccGetCallStatistics:
   Call Stats=0x4A5346FC, Call Id=23
//22/5A001212800B/CCAPI/ccConferenceDestroy:
   Conference Id=0xC, Tag=0x0
//22/xxxxxxxxxxxx/CCAPI/cc_api_bridge_drop_done:
   Conference Id=0xC, Source Interface=0x49E07FD4, Source Call Id=22,
   Destination Call Id=23, Disposition=0x0, Tag=0x0
//23/xxxxxxxxxxxx/CCAPI/cc_api_bridge_drop_done:
   Conference Id=0xC, Source Interface=0x495BABA4, Source Call Id=23,
   Destination Call Id=22, Disposition=0x0, Tag=0x0
//22/5A001212800B/CCAPI/cc_generic_bridge_done:
   Conference Id=0xC, Source Interface=0x495BABA4, Source Call Id=23,
   Destination Call Id=22, Disposition=0x0, Tag=0x0
//22/5A001212800B/CCAPI/ccCallDisconnect:
   Cause Value=16, Tag=0x0, Call Entry(Previous Disconnect Cause=0, Disconnect Cause=0)
//22/5A001212800B/CCAPI/ccCallDisconnect:
   Cause Value=16, Call Entry(Responsed=TRUE, Cause Value=16)
//22/5A001212800B/CCAPI/cc_api_get_transfer_info:
   Transfer Number Is Null
//23/5A001212800B/CCAPI/ccCallDisconnect:
   Cause Value=16, Tag=0x0, Call Entry(Previous Disconnect Cause=0, Disconnect Cause=0)
//23/5A001212800B/CCAPI/ccCallDisconnect:
   Cause Value=16, Call Entry(Responsed=TRUE, Cause Value=16)
//23/5A001212800B/CCAPI/cc_api_call_disconnect_done:
   Disposition=0, Interface=0x495BABA4, Tag=0x0, Call Id=23,
   Call Entry(Disconnect Cause=16, Voice Class Cause Code=0, Retry Count=0)
//23/5A001212800B/CCAPI/cc_api_call_disconnect_done:
   Call Disconnect Event Sent
//-1/xxxxxxxxxxxx/CCAPI/cc_free_feature_vsa:
:cc_free_feature_vsa freeing 4821DDE8
//-1/xxxxxxxxxxxx/CCAPI/cc_free_feature_vsa:
vsacount in free is 1
//22/5A001212800B/CCAPI/cc_api_call_disconnect_done:
   Disposition=0, Interface=0x49E07FD4, Tag=0x0, Call Id=22,
   Call Entry(Disconnect Cause=16, Voice Class Cause Code=0, Retry Count=0)
//22/5A001212800B/CCAPI/cc_api_call_disconnect_done:
   Call Disconnect Event Sent
//-1/xxxxxxxxxxxx/CCAPI/cc_free_feature_vsa:
:cc_free_feature_vsa freeing 4821DEC8
//-1/xxxxxxxxxxxx/CCAPI/cc_free_feature_vsa:
vsacount in free is 0
ISDN Se0/0/0:23 Q931: TX -> RELEASE pd = 8 callref = 0x8096
ISDN Se0/0/0:23 Q931: RX <- RELEASE_COMP pd = 8 callref = 0x0096
ISDN Se0/0/0:23 Q931: RX <- SETUP pd = 8 callref = 0x0097
        Bearer Capability i = 0x8090A2
                Standard = CCITT
                Transfer Capability = Speech
                Transfer Mode = Circuit
                Transfer Rate = 64 kbit/s
        Channel ID i = 0xA18381
                Preferred, Channel 1
        Progress Ind i = 0x8183 - Origination address is non-ISDN
        Display i = 'Seattle US Phone'
        Calling Party Number i = 0x4180, '2065015111'
                Plan:ISDN, Type:Subscriber(local)
        Called Party Number i = 0xC1, '2065011001'
                Plan:ISDN, Type:Subscriber(local)
//-1/xxxxxxxxxxxx/CCAPI/ccIFCallSetupRequestPrivate:
   Interface=0x49E07FD4, Interface Type=6, Destination=, Mode=0x9,
   Call Params(Calling Number=,(Calling Name=)(TON=Unknown, NPI=Unknown, Screening=Not Screened, Presentation=Allowed),
   Called Number=(TON=Unknown, NPI=Unknown), Calling Translated=FALSE,
   Subscriber Type Str=, FinalDestinationFlag=FALSE, Outgoing Dial-peer=0, Call Count On=FALSE,
   Source Trkgrp Route Label=, Target Trkgrp Route Label=, tg_label_flag=0, Application Call Id=D000000002f5368f000000F580000097)
//-1/xxxxxxxxxxxx/CCAPI/cc_get_feature_vsa:
:cc_get_feature_vsa malloc success
//-1/xxxxxxxxxxxx/CCAPI/cc_get_feature_vsa:
cc_get_feature_vsa count is 1
//-1/xxxxxxxxxxxx/CCAPI/cc_get_feature_vsa:
:FEATURE_VSA attributes are: feature_name:0,feature_time:1210179280,feature_id:24
//24/74820328800C/CCAPI/ccIFCallSetupRequestPrivate:
   SPI Call Setup Request Is Success; Interface Type=6, FlowMode=1
//24/74820328800C/CCAPI/ccCallSetContext:
   Context=0x4A524790
//-1/xxxxxxxxxxxx/CCAPI/ccIFCallSetupRequestPrivate:
   Interface=0x495BABA4, Interface Type=9, Destination=0.0.0.0, Mode=0x9,
   Call Params(Calling Number=,(Calling Name=)(TON=Unknown, NPI=Unknown, Screening=Not Screened, Presentation=Allowed),
   Called Number=(TON=Unknown, NPI=Unknown), Calling Translated=FALSE,
   Subscriber Type Str=, FinalDestinationFlag=FALSE, Outgoing Dial-peer=0, Call Count On=TRUE,
   Source Trkgrp Route Label=, Target Trkgrp Route Label=, tg_label_flag=0, Application Call Id=D000000002f5368f000000F580000097)
//-1/xxxxxxxxxxxx/CCAPI/cc_get_feature_vsa:
:cc_get_feature_vsa malloc success
//-1/xxxxxxxxxxxx/CCAPI/cc_get_feature_vsa:
cc_get_feature_vsa count is 2
//-1/xxxxxxxxxxxx/CCAPI/cc_get_feature_vsa:
:FEATURE_VSA attributes are: feature_name:0,feature_time:1210179056,feature_id:25
//25/74820328800C/CCAPI/ccIFCallSetupRequestPrivate:
   SPI Call Setup Request Is Success; Interface Type=9, FlowMode=1
//25/74820328800C/CCAPI/ccCallSetContext:
   Context=0x4A524580
//25/74820328800C/CCAPI/cc_api_call_connected:
   Interface=0x495BABA4, Data Bitmask=0x0, Progress Indication=NULL(0),
   Connection Handle=0
//25/74820328800C/CCAPI/cc_api_call_connected:
   Call Entry(Connected=TRUE, Responsed=TRUE, Retry Count=0)
//24/74820328800C/CCAPI/cc_api_call_proceeding:
   Interface=0x49E07FD4, Progress Indication=NULL(0)
//24/74820328800C/CCAPI/cc_api_call_connected:
   Interface=0x49E07FD4, Data Bitmask=0x1, Progress Indication=DESTINATION IS NON ISDN(2),
   Connection Handle=0
//24/74820328800C/CCAPI/cc_api_call_connected:
   Call Entry(Connected=TRUE, Responsed=TRUE, Retry Count=0)
//24/74820328800C/CCAPI/ccCallModify:
   Nominator=0x1000, Params=0x4A2E7368, Call Id=24
//24/xxxxxxxxxxxx/CCAPI/ccCallReportDigits:
   (callID=0x18, digit_event=0x1, enable=TRUE, consume=FALSE)
//24/74820328800C/CCAPI/ccCallReportDigits:
   Enabled=TRUE, Call Id=24
//24/xxxxxxxxxxxx/CCAPI/cc_api_call_report_digits_done:
   (vdbPtr=0x49E07FD4, callID=0x18, disp=0, digit_event=0x1, enable=TRUE, consume=FALSE)
//24/74820328800C/CCAPI/cc_api_call_report_digits_done:
   Enabled=TRUE, Disposition=0x0, Interface=0x49E07FD4, Call Id=24
//24/74820328800C/CCAPI/cc_api_call_report_digits_done:
   Call Entry(Initial Digit Timeout=15000(ms), Inter Digit Timeout=10000(ms))
//24/xxxxxxxxxxxx/CCAPI/ccConferenceCreate:
   (confID=0x4A2E757C, callID1=0x18, callID2=0x19, tag=0x0)
//24/xxxxxxxxxxxx/CCAPI/ccConferenceCreate:
   (confID=0x4A2E757C, callID1=0x18, gcid=0-0-0-0, tag=0x0)
//25/xxxxxxxxxxxx/CCAPI/ccConferenceCreate:
   (confID=0x4A2E757C, callID2=0x19, gcid=0-0-0-0, tag=0x0)
//24/74820328800C/CCAPI/ccConferenceCreate:
   Conference Id=0x4A2E757C, Call Id1=24, Call Id2=25, Tag=0x0
//24/xxxxxxxxxxxx/CCAPI/cc_api_bridge_done:
   Conference Id=0xD, Source Interface=0x49E07FD4, Source Call Id=24,
   Destination Call Id=25, Disposition=0x0, Tag=0xFFFFFFFF
//25/xxxxxxxxxxxx/CCAPI/cc_api_bridge_done:
   Conference Id=0xD, Source Interface=0x495BABA4, Source Call Id=25,
   Destination Call Id=24, Disposition=0x0, Tag=0x0
//24/74820328800C/CCAPI/cc_generic_bridge_done:
   Conference Id=0xD, Source Interface=0x495BABA4, Source Call Id=25,
   Destination Call Id=24, Disposition=0x0, Tag=0x0
//24/74820328800C/CCAPI/ccConferenceCreate:
   Call Entry(Conference Id=0xD, Destination Call Id=25)
//25/74820328800C/CCAPI/ccConferenceCreate:
   Call Entry(Conference Id=0xD, Destination Call Id=24)
//24/74820328800C/CCAPI/cc_api_caps_ind:
   Destination Interface=0x495BABA4, Destination Call Id=25, Source Call Id=24,
   Caps(Codec=0x1, Fax Rate=0x1, Vad=0x1,
   Modem=0x2, Codec Bytes=20, Signal Type=3)
//24/74820328800C/CCAPI/cc_api_caps_ind:
   Caps(Playout Mode=1, Playout Initial=60(ms), Playout Min=40(ms),
   Playout Max=1000(ms), Fax Nom=300(ms))
//25/74820328800C/CCAPI/cc_api_caps_ind:
   Destination Interface=0x49E07FD4, Destination Call Id=24, Source Call Id=25,
   Caps(Codec=0x4, Fax Rate=0x2, Vad=0x1,
   Modem=0x0, Codec Bytes=20, Signal Type=2)
//25/74820328800C/CCAPI/cc_api_caps_ind:
   Caps(Playout Mode=1, Playout Initial=60(ms), Playout Min=40(ms),
   Playout Max=1000(ms), Fax Nom=300(ms))
//25/74820328800C/CCAPI/cc_api_caps_ack:
   Destination Interface=0x49E07FD4, Destination Call Id=24, Source Call Id=25,
   Caps(Codec=g729r8(0x4), Fax Rate=FAX_RATE_VOICE(0x2), Vad=OFF(0x1),
   Modem=OFF(0x0), Codec Bytes=20, Signal Type=2, Seq Num Start=9314)
//24/74820328800C/CCAPI/cc_api_caps_ack:
   Destination Interface=0x495BABA4, Destination Call Id=25, Source Call Id=24,
   Caps(Codec=g729r8(0x4), Fax Rate=FAX_RATE_VOICE(0x2), Vad=OFF(0x1),
   Modem=OFF(0x0), Codec Bytes=20, Signal Type=2, Seq Num Start=9314)
//24/74820328800C/CCAPI/cc_api_call_modify_done:
   Result=0, Interface=0x49E07FD4, Call Id=24
//24/74820328800C/CCAPI/cc_api_voice_mode_event:
   Call Id=24
//24/74820328800C/CCAPI/cc_api_voice_mode_event:
   Call Entry(Context=0x4A524790)
//24/74820328800C/CCAPI/cc_process_notify_bridge_done:
   Conference Id=0xD, Call Id1=24, Call Id2=25
//24/74820328800C/CCAPI/ccSetDigitTimeouts:
   Initial Digit Timeout=4000(ms), Inter Digit Timeout=4000(ms)
//24/74820328800C/CCAPI/ccSetDigitTimeouts:
   Call Entry(Inter Digit Timeout=4000(ms), Initial Digit Timeout=4000(ms))
//24/74820328800C/CCAPI/ccRestartDigitTimeoutMsec:
   Digit Timeout=0, Call Id=24
//24/xxxxxxxxxxxx/CCAPI/ccCallReportDigits:
   (callID=0x18, digit_event=0x1, enable=TRUE, consume=FALSE)
//24/74820328800C/CCAPI/ccCallReportDigits:
   Enabled=TRUE, Call Id=24
//24/xxxxxxxxxxxx/CCAPI/cc_api_call_report_digits_done:
   (vdbPtr=0x49E07FD4, callID=0x18, disp=0, digit_event=0x1, enable=TRUE, consume=FALSE)
//24/74820328800C/CCAPI/cc_api_call_report_digits_done:
   Enabled=TRUE, Disposition=0x0, Interface=0x49E07FD4, Call Id=24
//24/74820328800C/CCAPI/cc_api_call_report_digits_done:
   Call Entry(Initial Digit Timeout=4000(ms), Inter Digit Timeout=4000(ms))
ISDN Se0/0/0:23 Q931: TX -> CALL_PROC pd = 8 callref = 0x8097
        Channel ID i = 0xA98381
                Exclusive, Channel 1
//24/74820328800C/CCAPI/ccCallModify:
   Nominator=0x1000, Params=0x4A2E6E68, Call Id=24
//24/74820328800C/CCAPI/cc_api_call_modify_done:
   Result=0, Interface=0x49E07FD4, Call Id=24
ISDN Se0/0/0:23 Q931: TX -> ALERTING pd = 8 callref = 0x8097
        Progress Ind i = 0x8088 - In-band info or appropriate now available
//24/74820328800C/CCAPI/ccGenerateToneInfo:
   Stop Tone On Digit=FALSE, Tone=Ring Back,
   Tone Direction=Network, Params=0x0, Call Id=24
//24/74820328800C/CCAPI/cc_handle_inter_digit_timer:
   Generate inter-digit timeout CC_EV_CALL_DIGIT_END event
The following INBOUND call from the PSTN to 5126022001 fails and is supposed to be routing through Branch1 and is instead routing through CorpHQ. Please see 'DEBUG VOIP CCAPI INOUT'
CorpHQ#
//-1/A31ADF52800B/CCAPI/cc_api_display_ie_subfields:
   cc_api_call_setup_ind_common:
   cisco-username=
   ----- ccCallInfo IE subfields -----
   cisco-ani=5126026222
   cisco-anitype=4
   cisco-aniplan=1
   cisco-anipi=0
   cisco-anisi=0
   dest=5126022001
   cisco-desttype=4
   cisco-destplan=1
   cisco-rdie=FFFFFFFF
   cisco-rdn=
   cisco-lastrdn=
   cisco-rdntype=-1
   cisco-rdnplan=-1
   cisco-rdnpi=-1
   cisco-rdnsi=-1
   cisco-redirectreason=-1   fwd_final_type =0
   final_redirectNumber =
   hunt_group_timeout =0
//-1/A31ADF52800B/CCAPI/cc_api_call_setup_ind_common:
   Interface=0x49F42894, Call Info(
   Calling Number=5126026222,(Calling Name=)(TON=Subscriber, NPI=ISDN, Screening=Not Screened, Presentation=Allowed),
   Called Number=5126022001(TON=Subscriber, NPI=ISDN),
   Calling Translated=FALSE, Subscriber Type Str=RegularLine, FinalDestinationFlag=TRUE,
   Incoming Dial-peer=1, Progress Indication=ORIGINATING SIDE IS NON ISDN(3), Calling IE Present=TRUE,
   Source Trkgrp Route Label=, Target Trkgrp Route Label=, CLID Transparent=FALSE), Call Id=-1
//-1/A31ADF52800B/CCAPI/ccCheckClipClir:
   In: Calling Number=5126026222(TON=Subscriber, NPI=ISDN, Screening=Not Screened, Presentation=Allowed)
//-1/A31ADF52800B/CCAPI/ccCheckClipClir:
   Out: Calling Number=5126026222(TON=Subscriber, NPI=ISDN, Screening=Not Screened, Presentation=Allowed)
//-1/xxxxxxxxxxxx/CCAPI/cc_get_feature_vsa:
:cc_get_feature_vsa malloc success
//-1/xxxxxxxxxxxx/CCAPI/cc_get_feature_vsa:
cc_get_feature_vsa count is 1
//-1/xxxxxxxxxxxx/CCAPI/cc_get_feature_vsa:
:FEATURE_VSA attributes are: feature_name:0,feature_time:1241383960,feature_id:13
//13/A31ADF52800B/CCAPI/cc_api_call_setup_ind_common:
   Set Up Event Sent;
   Call Info(Calling Number=5126026222(TON=Subscriber, NPI=ISDN, Screening=Not Screened, Presentation=Allowed),
   Called Number=5126022001(TON=Subscriber, NPI=ISDN))
//13/A31ADF52800B/CCAPI/cc_process_call_setup_ind:
   Event=0x497D0010
//-1/xxxxxxxxxxxx/CCAPI/cc_setupind_match_search:
   Try with the demoted called number 5126022001
//13/A31ADF52800B/CCAPI/ccCallSetContext:
   Context=0x4A131A54
//13/A31ADF52800B/CCAPI/cc_process_call_setup_ind:
   >>>>CCAPI handed cid 13 with tag 1 to app "_ManagedAppProcess_Default"
//13/A31ADF52800B/CCAPI/ccCallProceeding:
   Progress Indication=NULL(0)
//13/A31ADF52800B/CCAPI/ccCallDisconnect:
   Cause Value=1, Tag=0x0, Call Entry(Previous Disconnect Cause=0, Disconnect Cause=0)
//13/A31ADF52800B/CCAPI/ccCallDisconnect:
   Cause Value=1, Call Entry(Responsed=TRUE, Cause Value=1)
//13/A31ADF52800B/CCAPI/cc_api_get_transfer_info:
   Transfer Number Is Null
//13/A31ADF52800B/CCAPI/cc_api_call_disconnect_done:
   Disposition=0, Interface=0x49F42894, Tag=0x0, Call Id=13,
   Call Entry(Disconnect Cause=1, Voice Class Cause Code=0, Retry Count=0)
//13/A31ADF52800B/CCAPI/cc_api_call_disconnect_done:
   Call Disconnect Event Sent
//-1/xxxxxxxxxxxx/CCAPI/cc_free_feature_vsa:
:cc_free_feature_vsa freeing 49FE0410
//-1/xxxxxxxxxxxx/CCAPI/cc_free_feature_vsa:
vsacount in free is 0
PSTN#sh run
Building configuration...
Current configuration : 13975 bytes
! No configuration change since last restart
version 12.4
no service pad
no service timestamps debug uptime
no service timestamps log uptime
no service password-encryption
hostname PSTN
boot-start-marker
boot-end-marker
card type e1 0 0
card type t1 0 1
logging message-counter syslog
no aaa new-model
clock timezone EST -5
clock summer-time EST recurring
network-clock-participate wic 0
network-clock-participate wic 1
no network-clock-participate aim 0
dot11 syslog
ip source-route
ip cef
no ip domain lookup
ip domain name att.com
ip name-server 177.1.100.110
ip multicast-routing
no ipv6 cef
multilink bundle-name authenticated
isdn switch-type primary-ni
voice service voip
allow-connections h323 to h323
allow-connections h323 to sip
allow-connections sip to h323
allow-connections sip to sip
redirect ip2ip
fax protocol cisco
sip
bind control source-interface Loopback10
bind media source-interface Loopback10
header-passing
voice translation-rule 101
rule 1 /^\+.*/ //
rule 2 /^501.*/ //
rule 3 /^1206.*/ //
rule 4 /^00.*/ //
rule 5 /^0011.*/ //
rule 6 /^206/ /1206/
rule 7 /^1512.*/ /\0/
rule 8 /^011$.*$/ /\1/
voice translation-rule 102
rule 1 /^1$2065015111$$/ /\1/ type any subscriber plan any isdn
rule 2 /^1$2065015555$$/ /\1/ type any subscriber plan any isdn
rule 3 /^1$2065015151$$/ /\1/ type any subscriber plan any isdn
rule 4 /^1$5126026222$$/ /\1/ type any national plan any isdn
rule 5 /^31670357575$/ /&/ type any international plan any isdn
rule 6 /^31207037333$/ /&/ type any international plan any isdn
rule 7 /^31107047444$/ /&/ type any international plan any isdn
rule 8 /^911$/ /&/ type any unknown plan any unknown
rule 9 /^15126022.../ /&/ type any unknown plan any unknown
rule 10 /^31207033.../ /&/ type any unknown plan any unknown
rule 11 /^....$/ /&/ type any unknown plan any unknown
voice translation-rule 103
rule 1 /^206.*/ /&/ type any subscriber plan any isdn
rule 2 /^1/ // type any national plan any isdn
rule 3 /^00/ // type any international plan any isdn
voice translation-rule 201
rule 1 /^\+.*/ //
rule 2 /^602.*/ //
rule 3 /^1512.*/ //
rule 4 /^00.*/ //
rule 5 /^0011.*/ //
rule 6 /^512/ /1&/
rule 7 /^1206.*/ /&/
rule 8 /^011$31.*$/ /\1/
voice translation-rule 202
rule 1 /^1$5126026222$$/ /\1/ type any subscriber plan any isdn
rule 2 /^1$2065015555$$/ /\1/ type any national plan any isdn
rule 3 /^1$2065015151$$/ /\1/ type any national plan any isdn
rule 4 /^1$2065015111$$/ /\1/ type any national plan any isdn
rule 5 /^31670357575$/ /&/ type any international plan any isdn
rule 6 /^31207037333$/ /&/ type any international plan any isdn
rule 7 /^31107047444$/ /&/ type any international plan any isdn
rule 8 /^911$/ /&/ type any unknown plan any unknown
rule 9 /^12065011.../ /&/ type any unknown plan any unknown
rule 10 /^31207033.../ /&/ type any unknown plan any unknown
rule 11 /^....$/ /&/ type any unknown plan any unknown
voice translation-rule 203
rule 1 /^512.*/ /&/ type any subscriber plan any isdn
rule 2 /^1/ // type any national plan any isdn
rule 3 /^00/ // type any international plan any isdn
voice translation-rule 301
rule 1 /^\+.*/ //
rule 2 /^20.*/ //
rule 3 /^0$[1-8].*$/ /31\1/
rule 4 /^011/ //
rule 5 /^0031/ //
rule 6 /^703..../ /3120&/
rule 7 /^00$1.*$/ /\1/
voice translation-rule 302
rule 1 /^31207037333$/ /7037333/ type any subscriber plan any isdn
rule 2 /^7033$...$$/ /0207033\1/
rule 3 /^911$/ /112/ type any unknown plan any unknown
rule 4 /^31$670357575$$/ /0\1/ type any national plan any isdn
rule 5 /^31$107047444$$/ /0\1/ type any national plan any isdn
rule 6 /^12065015555$/ /&/ type any international plan any isdn
rule 7 /^12065015151$/ /&/ type any international plan any isdn
rule 8 /^12065015111$/ /&/ type any international plan any isdn
rule 9 /^15126026222$/ /&/ type any international plan any isdn
rule 10 /^12065011...$/ /&/ type any unknown plan any unknown
rule 11 /^15126022...$/ /&/ type any unknown plan any unknown
rule 12 /^....$/ /&/ type any unknown plan any unknown
voice translation-rule 303
rule 1 /^703.*/ /&/ type any subscriber plan any isdn
rule 2 /^010/ // type any national plan any isdn
rule 3 /^1/ // type any international plan any isdn
voice translation-rule 1000
rule 1 /.*$1...$$/ /206501\1/
rule 2 /.*$2...$$/ /512602\1/
rule 3 /.*$45..$$/ /020757\1/
voice translation-rule 1001
rule 1 /^1206...5...$/ /+&/
rule 2 /^1512...6...$/ /+&/
rule 3 /^31.0...7...$/ /+&/
voice translation-profile 1-HQ-Change_DNIS-Check_ANI
translate called 101
voice translation-profile 1-HQ-Proper_Types
translate calling 102
translate called 103
voice translation-profile 2-BR1-Change_DNIS-Check_ANI
translate called 201
voice translation-profile 2-BR1-Proper_Types
translate calling 202
translate called 203
voice translation-profile 3-BR2-Change_DNIS-Check_ANI
translate called 301
voice translation-profile 3-BR2-Proper_Types
translate calling 302
translate called 303
voice translation-profile SIP-NORMALIZE-DNIS-ANI
translate calling 1001
translate called 1000
voice-card 0
dspfarm
archive
log config
hidekeys
controller E1 0/0/0
clock source internal
pri-group timeslots 1-3,16
description == Voice Circuit to Branch2
controller T1 0/1/0
clock source internal
cablelength long 0db
pri-group timeslots 1-3,24
description == Voice Circuit to CorpHQ
controller T1 0/1/1
clock source internal
cablelength long 0db
pri-group timeslots 1-3,24
description == Voice Circuit to Branch1
interface Loopback0
ip address 177.1.254.254 255.255.255.255
interface Loopback10
ip address 177.1.254.250 255.255.255.255
interface Loopback11
ip address 177.1.254.251 255.255.255.255
interface FastEthernet0/0
description ==TO INTERNET==
ip address 192.168.1.150 255.255.255.0
duplex auto
speed auto
interface FastEthernet0/1
description === To HQ
ip address 177.1.19.1 255.255.255.0
duplex auto
speed auto
interface Serial0/0/0:15
description == PRI Circuit to R3-BR2
no ip address
encapsulation hdlc
isdn switch-type primary-net5
isdn protocol-emulate network
isdn incoming-voice voice
isdn negotiate-bchan resend-setup
no isdn outgoing ie network-facility
isdn outgoing display-ie
no cdp enable
interface Serial0/1/0:23
description == PRI Circuit to R1-HQ
no ip address
encapsulation hdlc
isdn switch-type primary-5ess
isdn protocol-emulate network
isdn incoming-voice voice
isdn negotiate-bchan
isdn outgoing display-ie
no cdp enable
interface Serial0/1/1:23
description == PRI Circuit to R2-BR1
no ip address
encapsulation hdlc
isdn switch-type primary-ni
isdn protocol-emulate network
isdn incoming-voice voice
isdn supp-service name calling
isdn negotiate-bchan resend-setup
isdn outgoing ie network-facility
no cdp enable
router ospf 1
log-adjacency-changes
network 0.0.0.0 255.255.255.255 area 0
ip forward-protocol nd
ip route 0.0.0.0 0.0.0.0 192.168.1.1
ip http server
ip http authentication local
no ip http secure-server
ip http path flash:
control-plane
voice-port 0/0/0:15
translation-profile incoming 3-BR2-Change_DNIS-Check_ANI
description == Voice PRI to Branch2
voice-port 0/1/0:23
translation-profile incoming 1-HQ-Change_DNIS-Check_ANI
description == Voice PRI to CorpHQ
voice-port 0/1/1:23
translation-profile incoming 2-BR1-Change_DNIS-Check_ANI
description == Voice PRI to Branch1
dial-peer voice 1 pots
description == All inbound calls from HQ BR1 BR2 into PSTN
incoming called-number .
direct-inward-dial
dial-peer voice 101 pots
description == Subscriber Calls from PSTN into CorpHQ
translation-profile outgoing 1-HQ-Proper_Types
preference 1
destination-pattern ^2065011...$
direct-inward-dial
port 0/1/0:23
forward-digits 10
dial-peer voice 102 pots
description == National Calls from PSTN into CorpHQ
translation-profile outgoing 1-HQ-Proper_Types
preference 1
destination-pattern ^12065011...$
direct-inward-dial
port 0/1/0:23
forward-digits 10
dial-peer voice 103 pots
description == International Calls into CorpHQ from PSTN Coming from NL Ph
translation-profile outgoing 1-HQ-Proper_Types
preference 1
destination-pattern ^0012065011...$
direct-inward-dial
port 0/1/0:23
forward-digits 10
dial-peer voice 104 pots
description == + Calls into CorpHQ from PSTN Coming from Mobiles
translation-profile outgoing 1-HQ-Proper_Types
preference 1
destination-pattern +12065011...$
direct-inward-dial
port 0/1/0:23
forward-digits 10
dial-peer voice 201 pots
description == Subscriber Calls from PSTN into Branch1
translation-profile outgoing 2-BR1-Proper_Types
preference 1
destination-pattern ^5126022...$
direct-inward-dial
port 0/1/1:23
forward-digits 10
dial-peer voice 202 pots
description == National Calls from PSTN into Branch1
translation-profile outgoing 2-BR1-Proper_Types
preference 1
destination-pattern ^15126022...$
direct-inward-dial
port 0/1/1:23
forward-digits 10
dial-peer voice 203 pots
description == International Calls into Branch1 from PSTN Coming from NL Ph
translation-profile outgoing 2-BR1-Proper_Types
preference 1
destination-pattern ^0015126022...$
direct-inward-dial
port 0/1/1:23
forward-digits 10
dial-peer voice 204 pots
description == + Calls into Branch1 from PSTN Coming from Mobiles
translation-profile outgoing 2-BR1-Proper_Types
preference 1
destination-pattern +15126022...$
direct-inward-dial
port 0/1/1:23
forward-digits 10
dial-peer voice 301 pots
description == Subscriber Calls from PSTN into Branch2
translation-profile outgoing 3-BR2-Proper_Types
destination-pattern ^7033...$
direct-inward-dial
port 0/0/0:15
forward-digits 7
dial-peer voice 302 pots
description == National Calls from PSTN into Branch2
translation-profile outgoing 3-BR2-Proper_Types
destination-pattern ^0207033...$
direct-inward-dial
port 0/0/0:15
forward-digits 10
dial-peer voice 303 pots
description == International Calls into Branch2 from PSTN Coming from US Ph
translation-profile outgoing 3-BR2-Proper_Types
destination-pattern ^01131207033...$
direct-inward-dial
port 0/0/0:15
forward-digits 9
prefix 0
dial-peer voice 304 pots
description == International Calls into Branch2 from PSTN Coming from US Ph
translation-profile outgoing 3-BR2-Proper_Types
destination-pattern ^31207033...$
direct-inward-dial
port 0/0/0:15
forward-digits 9
prefix 0
dial-peer voice 305 pots
description == + Calls into Branch2 from PSTN Coming from Mobiles
translation-profile outgoing 3-BR2-Proper_Types
destination-pattern +31207033...$
direct-inward-dial
port 0/0/0:15
forward-digits 9
prefix 0
dial-peer voice 1000 voip
description == Calls into AT&T SIP ITSP for VC Week1 Lab1
rtp payload-type nse 99
rtp payload-type nte 100
voice-class sip localhost dns:sip1.att.com
session protocol sipv2
incoming called-number .
dtmf-relay rtp-nte
codec g711ulaw
dial-peer voice 5000 voip
service aa
destination-pattern A5000
session target ipv4:177.1.254.254
incoming called-number A5000
dtmf-relay h245-alphanumeric
codec g711ulaw
no vad
num-exp 1888....... 911
num-exp 1900....... 911
num-exp 1976....... 911
num-exp 1777....... 911
num-exp 1444....... 911
num-exp 0800....... 911
num-exp 0900....... 911
sip-ua
telephony-service
no auto-reg-ephone
max-ephones 1
max-dn 10
ip source-address 177.1.254.254 port 2000
caller-id block code *67
system message You WILL PASS this Exam!
voicemail A5000
max-conferences 8 gain -6
call-forward pattern .T
dn-webedit
transfer-system full-consult
transfer-pattern .T
create cnf-files version-stamp 7960 Sep 01 2012 15:29:37
ephone-dn 1 dual-line
number 12065015111 secondary +12065015111
label Seattle, US +1 206 501 5111
description INE PSTN Phone
name Seattle US Phone
ephone-dn 2 dual-line
number 15126026222 secondary +15126026222
label Austin, US +1 512 602 6222
name Austin TX Phone
ephone-dn 3 dual-line
number 31207037333 secondary +31207037333
label Amsterdam, NL +31 20 703 73 33
name Amsterdam NL Phone
ephone-dn 4 dual-line
number 12065015555 secondary +12065015555
label Hurley Mobile +1 206 501 5555
name Hurley's Mobile
call-forward busy A5000
call-forward noan A5000 timeout 16
ephone-dn 5 dual-line
number 12065015151 secondary +12065015151
label Hurley's Home +1 206 501 5151
name Hurley's Home
call-forward busy A5000
call-forward noan A5000 timeout 12
ephone-dn 6 dual-line
number 31670357575 secondary +31670357575
label Sawyer's Mobile +31 6 70357575
name Sawyer's Mobile
call-forward busy A5000
call-forward noan A5000 timeout 16
ephone-dn 7 dual-line
number 911 secondary 112
label US/EU Emer/FreePhone/Prem
name Emergency Services
ephone-dn 8 dual-line
number 15126026262 secondary +15126026262
label BLinus Mobile +1 512 602 6262
name Benjamin Linus Mobile
call-forward busy A5000
call-forward noan A5000 timeout 16
ephone-dn 9 dual-line
number 31207037373 secondary +31207037373
label DHume Home +31 20 703 73 73
name Desmond Hume Home
call-forward busy A5000
call-forward noan A5000 timeout 16
ephone-dn 10 dual-line
number 31107047444 secondary +31107047444
label Rotterdam, NL +31 10 704 74 44
name Rotterdam NL Phone
ephone 1
device-security-mode none
mac-address A456.3040.0DAA
type 7975
button 1:1 2:2 3:3 4:10
button 5:6 6o7,8,5,4
line con 0
exec-timeout 0 0
privilege level 15
logging synchronous level 0 limit 20
line aux 0
line vty 0 4
exec-timeout 0 0
privilege level 15
logging synchronous
no login
line vty 5 15
exec-timeout 0 0
privilege level 15
logging synchronous
no login
scheduler allocate 20000 1000
ntp source Loopback0
ntp master 10
ntp server 64.90.182.55
end
CorpHQ#sh run
Building configuration...
Current configuration : 6353 bytes
! No configuration change since last restart
version 12.4
no service pad
no service timestamps debug uptime
no service timestamps log uptime
no service password-encryption
hostname CorpHQ
boot-start-marker
boot-end-marker
logging message-counter syslog
no aaa new-model
clock timezone PST -8
clock summer-time PDT recurring
network-clock-participate wic 0
network-clock-select 1 T1 0/0/0
dot11 syslog
ip source-route
ip cef
ip dhcp excluded-address 177.1.11.1 177.1.11.14
ip dhcp excluded-address 177.1.11.21 177.1.11.254
ip dhcp excluded-address 177.2.11.1 177.2.11.14
ip dhcp excluded-address 177.2.11.21 177.2.11.254
ip dhcp pool CorpHQ-Phones
   network 177.1.11.0 255.255.255.0
   option 150 ip 177.1.10.10 177.1.10.20
   default-router 177.1.11.1
   dns-server 177.1.100.110
ip dhcp pool Branch1-Phones
   network 177.2.11.0 255.255.255.0
   option 150 ip 177.1.10.10 177.1.10.20
   default-router 177.2.11.1
   dns-server 177.1.100.110
no ip domain lookup
ip multicast-routing
no ipv6 cef
multilink bundle-name authenticated
isdn switch-type primary-ni
voice service voip
allow-connections h323 to h323
fax protocol cisco
sip
bind control source-interface Loopback0
bind media source-interface Loopback0
no update-callerid
voice class codec 1
codec preference 1 g711ulaw
codec preference 2 g711alaw
codec preference 3 g729r8
voice translation-rule 1
rule 1 // // type any subscriber plan any isdn
voice translation-rule 2
rule 1 // // type any national plan any isdn
voice translation-rule 3
rule 1 // // type any international plan any isdn
voice translation-rule 10
rule 1 /^[2-9].........$/ /9&/
rule 2 /^1[2-9].........$/ /9&/
rule 3 /^011/ /9&/
voice translation-profile MakeInternational
translate called 3
voice translation-profile MakeNational
translate called 2
voice translation-profile MakeSubscriber
translate called 1
voice translation-profile Prefix9_InFrom_CUCM
translate called 10
voice-card 0
dsp services dspfarm
archive
log config
hidekeys
controller T1 0/0/0
pri-group timeslots 1-3,24
description == Voice Circuit to PSTN
interface Loopback0
ip address 177.1.254.1 255.255.255.255
ip pim dense-mode
interface FastEthernet0/0
description == To CorpHQ-Switch
no ip address
duplex auto
speed auto
interface FastEthernet0/0.10
description == Server VLAN
encapsulation dot1Q 10
ip address 177.1.10.1 255.255.255.0
ip pim dense-mode
interface FastEthernet0/0.11
description == Voice VLAN
encapsulation dot1Q 11
ip address 177.1.11.1 255.255.255.0
ip helper-address 177.1.10.10
ip nbar protocol-discovery
ip pim dense-mode
interface FastEthernet0/0.12
description == Data VLAN
encapsulation dot1Q 12
ip address 177.1.12.1 255.255.255.0
interface FastEthernet0/0.13
description == PSTN PHONE VLAN
encapsulation dot1Q 13
ip address 177.1.13.1 255.255.255.0
interface FastEthernet0/1
description === To PSTN
ip address 177.1.19.254 255.255.255.0
duplex auto
speed auto
interface Serial0/0/0:23
no ip address
encapsulation hdlc
isdn switch-type primary-ni
isdn incoming-voice voice
no cdp enable
interface Serial0/1/0
description == Frame-Relay Circuit to WAN
no ip address
encapsulation frame-relay
fair-queue 64 256 36
cdp enable
frame-relay lmi-type ansi
ip rsvp bandwidth
interface Serial0/1/0.1 point-to-point
description == FR To BR1
bandwidth 384
ip address 177.0.101.1 255.255.255.0
ip pim dense-mode
snmp trap link-status
frame-relay interface-dlci 101
ip rsvp bandwidth 136
interface Serial0/1/0.2 point-to-point
description == FR To BR2
ip address 177.0.201.1 255.255.255.0
snmp trap link-status
frame-relay interface-dlci 102
ip rsvp bandwidth 136
router ospf 1
log-adjacency-changes
network 0.0.0.0 255.255.255.255 area 0
ip forward-protocol nd
ip route 0.0.0.0 0.0.0.0 177.1.19.1
ip route 0.0.0.0 0.0.0.0 FastEthernet0/0.10
no ip http server
no ip http secure-server
control-plane
voice-port 0/0/0:23
voice-port 0/3/0
voice-port 0/3/1
ccm-manager music-on-hold
sccp local Loopback0
sccp ccm 177.1.10.10 identifier 1 priority 1 version 5.0.1
sccp ccm 177.1.10.20 identifier 2 priority 2 version 5.0.1
sccp ccm 177.1.254.3 identifier 3 priority 3 version 5.0.1
sccp
sccp ccm group 1
bind interface Loopback0
associate ccm 2 priority 1
associate ccm 1 priority 2
associate ccm 3 priority 3
associate profile 1 register CorpHQ-729-MTP
associate profile 2 register CorpHQ-711-MTP
associate profile 3 register CorpHQ-HW-Xcode
dspfarm profile 3 transcode
codec g711ulaw
codec g711alaw
codec g729ar8
codec g729abr8
codec g729r8
codec g729br8
codec ilbc
maximum sessions 2
associate application SCCP
dspfarm profile 1 mtp
codec g729ar8
codec g729r8
rsvp
maximum sessions software 10
associate application SCCP
dspfarm profile 2 mtp
codec g711ulaw
rsvp
maximum sessions software 10
associate application SCCP
dial-peer voice 1 pots
incoming called-number .
direct-inward-dial
dial-peer voice 10 pots
translation-profile outgoing MakeSubscriber
destination-pattern 911
no digit-strip
port 0/0/0:23
dial-peer voice 11 pots
translation-profile outgoing MakeSubscriber
destination-pattern 9[2-9]..[2-9]......$
port 0/0/0:23
dial-peer voice 12 pots
translation-profile outgoing MakeNational
destination-pattern 91[2-9]..[2-9]......$
port 0/0/0:23
forward-digits 11
dial-peer voice 13 pots
translation-profile outgoing MakeInternational
destination-pattern 9011T
port 0/0/0:23
prefix 011
dial-peer voice 100 voip
description == Inbound/Outbound SIP PSTN GW From/To CUCM Pub
translation-profile incoming Prefix9_InFrom_CUCM
destination-pattern ^2065011...$
voice-class codec 1
session protocol sipv2
session target ipv4:177.1.10.10
incoming called-number .
ip qos dscp cs3 signaling
dial-peer hunt 1
sip-ua
line con 0
exec-timeout 0 0
privilege level 15
logging synchronous level 0 limit 20
line aux 0
line vty 0 4
exec-timeout 0 0
privilege level 15
logging synchronous
no login
line vty 5 15
exec-timeout 0 0
privilege level 15
logging synchronous
no login
scheduler allocate 20000 1000
ntp source Loopback0
ntp master 2
ntp server 177.1.254.254
end
Branch1#sh run
Building configuration...
Current configuration : 3838 bytes
! Last configuration change at 01:19:02 CDT Thu Oct 10 2013
version 12.4
no service pad
no service timestamps debug uptime
no service timestamps log uptime
no service password-encryption
hostname Branch1
boot-start-marker
boot-end-marker
logging message-counter syslog
no aaa new-model
clock timezone CST -6
clock summer-time CDT recurring
network-clock-participate wic 0
network-clock-select 1 T1 0/0/0
dot11 syslog
ip source-route
ip cef
ip multicast-routing
no ipv6 cef
ntp update-calendar
ntp server 177.1.254.1
multilink bundle-name authenticated
isdn switch-type primary-ni
voice-card 0
dsp services dspfarm
archive
log config
hidekeys
controller T1 0/0/0
pri-group timeslots 1-3,24 service mgcp
interface Loopback0
ip address 177.1.254.2 255.255.255.255
interface FastEthernet0/0
no ip address
duplex auto
speed auto
interface FastEthernet0/0.11
description == Voice VLAN
encapsulation dot1Q 11
ip address 177.2.11.1 255.255.255.0
ip helper-address 177.1.254.1
ip pim dense-mode
interface FastEthernet0/0.12
description == Data VLAN
encapsulation dot1Q 12
ip address 177.2.12.1 255.255.255.0
interface FastEthernet0/1
no ip address
shutdown
duplex auto
speed auto
interface Serial0/0/0:23
no ip address
encapsulation hdlc
isdn switch-type primary-ni
isdn incoming-voice voice
isdn supp-service name calling
isdn bind-l3 ccm-manager
isdn outgoing ie facility
isdn outgoing display-ie
isdn outgoing ie redirecting-number
no cdp enable
interface Serial0/1/0
description == Frame-Relay Circuit to WAN
no ip address
encapsulation frame-relay
fair-queue 64 256 37
cdp enable
no frame-relay inverse-arp
frame-relay lmi-type ansi
ip rsvp bandwidth
interface Serial0/1/0.1 point-to-point
description == FR To HQ
ip address 177.0.101.2 255.255.255.0
ip pim dense-mode
snmp trap link-status
frame-relay interface-dlci 101
ip rsvp bandwidth 136
interface Serial0/1/1
no ip address
shutdown
clock rate 2000000
router ospf 1
log-adjacency-changes
network 0.0.0.0 255.255.255.255 area 0
ip forward-protocol nd
no ip http server
no ip http secure-server
control-plane
voice-port 0/0/0:23
ccm-manager fallback-mgcp
ccm-manager redundant-host 177.1.10.10
ccm-manager mgcp
no ccm-manager fax protocol cisco
ccm-manager music-on-hold
mgcp
mgcp call-agent 177.1.10.20 service-type mgcp version 0.1
mgcp dtmf-relay voip codec all mode out-of-band
mgcp fax t38 ecm
mgcp bind control source-interface Loopback0
mgcp bind media source-interface Loopback0
mgcp profile default
sccp local Loopback0
sccp ccm 177.1.254.3 identifier 3 priority 3 version 5.0.1
sccp ccm 177.1.10.10 identifier 1 priority 1 version 5.0.1
sccp ccm 177.1.10.20 identifier 2 priority 2 version 5.0.1
sccp
sccp ccm group 1
bind interface Loopback0
associate ccm 2 priority 1
associate ccm 1 priority 2
associate ccm 3 priority 3
associate profile 3 register Br1-HW-Xcode
associate profile 1 register Br1-729-MTP
associate profile 2 register Br1-711-MTP
dspfarm profile 3 transcode
codec g711ulaw
codec g711alaw
codec g729ar8
codec g729abr8
codec g729r8
codec g729br8
maximum sessions 2
associate application SCCP
dspfarm profile 1 mtp
codec g729ar8
codec g729r8
rsvp
maximum sessions software 10
associate application SCCP
dspfarm profile 2 mtp
codec g711ulaw
rsvp
maximum sessions software 10
associate application SCCP
line con 0
exec-timeout 0 0
privilege level 15
logging synchronous level 0 limit 20
line aux 0
line vty 0 4
exec-timeout 0 0
privilege level 15
logging synchronous
no login
line vty 5 15
exec-timeout 0 0
privilege level 15
logging synchronous
no login
scheduler allocate 20000 1000
end
Branch2#sh run
Building configuration...
Current configuration : 5789 bytes
! No configuration change since last restart
version 12.4
no service pad
no service timestamps debug uptime
no service timestamps log uptime
no service password-encryption
hostname Branch2
boot-start-marker
boot system flash:c2800nm-advipservicesk9-mz.124-24.T7.bin
boot system flash:
boot-end-marker
card type e1 0 0
logging message-counter syslog
no aaa new-model
clock timezone CEST 1
clock summer-time CEDT recurring
network-clock-participate wic 0
no network-clock-participate aim 0
dot11 syslog
ip source-route
ip cef
no ip domain lookup
no ipv6 cef
multilink bundle-name authenticated
isdn switch-type primary-net5
voice service voip
no supplementary-service h225-notify cid-update
fax protocol cisco
voice class codec 1
codec preference 1 g711ulaw
codec preference 2 g711alaw
codec preference 3 g729r8
voice class custom-cptone JOIN-TONE
dualtone conference
frequency 300 3600
cadence 150 100 500
voice class custom-cptone LEAVE-TONE
dualtone conference
frequency 300 3600
cadence 500 100 150
voice translation-rule 1
rule 1 /^7033...$/ /020&/
voice translation-rule 10
rule 1 /^0/ /0&/
voice translation-rule 200
rule 1 /^206501...$/ /1&/
voice translation-profile 7DigitDNIS-to-10Digit
translate called 1
voice translation-profile Prefix0_InFrom_CUCM
translate called 10
voice translation-profile Prefix1-toCorpHQ-ANI
translate calling 200
voice-card 0
dsp services dspfarm
archive
log config
hidekeys
controller E1 0/0/0
pri-group timeslots 1-3,16
description == Voice Circuit to PSTN
controller E1 0/0/1
interface Loopback0
ip address 177.1.254.3 255.255.255.255
h323-gateway voip bind srcaddr 177.1.254.3
interface FastEthernet0/0
no ip address
duplex auto
speed auto
interface FastEthernet0/0.11
encapsulation dot1Q 11
ip address 177.3.11.1 255.255.255.0
ip helper-address 177.1.10.10
interface FastEthernet0/0.12
encapsulation dot1Q 12
ip address 177.3.12.1 255.255.255.0
interface FastEthernet0/1
no ip address
shutdown
duplex auto
speed auto
interface Serial0/0/0:15
no ip address
encapsulation hdlc
isdn switch-type primary-net5
isdn incoming-voice voice
isdn bchan-number-order ascending
no cdp enable
interface Serial0/1/0
description == Frame-Relay Circuit to WAN
no ip address
encapsulation frame-relay
fair-queue 64 256 37
cdp enable
no frame-relay inverse-arp
frame-relay lmi-type ansi
ip rsvp bandwidth
interface Serial0/1/0.1 point-to-point
description == FR To HQ
ip address 177.0.201.2 255.255.255.0
snmp trap link-status
frame-relay interface-dlci 102
ip rsvp bandwidth 136
interface Serial0/1/1
no ip address
shutdown
clock rate 2000000
interface Service-Engine1/0
no ip address
shutdown
router ospf 1
log-adjacency-changes
network 0.0.0.0 255.255.255.255 area 0
ip forward-protocol nd
ip http server
ip http authentication local
no ip http secure-server
ip http path flash:
control-plane
voice-port 0/0/0:15
translation-profile incoming 7DigitDNIS-to-10Digit
ccm-manager music-on-hold
sccp local Loopback0
sccp ccm 177.1.10.20 identifier 2 priority 2 version 5.0.1
sccp ccm 177.1.10.10 identifier 1 priority 1 version 5.0.1
sccp ccm 177.1.254.3 identifier 3 priority 3 version 5.0.1
sccp
sccp ccm group 1
bind interface Loopback0
associate ccm 2 priority 1
associate ccm 1 priority 2
associate ccm 3 priority 3
associate profile 4 register Br2-HW-Conf
associate profile 3 register Br2-HW-Xcode
associate profile 2 register Br2-711-MTP
associate profile 1 register Br2-729-MTP
dspfarm profile 3 transcode
codec g711ulaw
codec g711alaw
codec g729ar8
codec g729abr8
codec g729r8
codec g729br8
maximum sessions 2
associate application SCCP
dspfarm profile 4 conference
codec g711ulaw
codec g711alaw
codec g729ar8
codec g729abr8
codec g729r8
codec g729br8
maximum sessions 1
conference-join custom-cptone JOIN-TONE
conference-leave custom-cptone LEAVE-TONE
associate application SCCP
dspfarm profile 1 mtp
codec g729ar8
codec g729r8
rsvp
maximum sessions software 10
associate application SCCP
dspfarm profile 2 mtp
codec g711ulaw
rsvp
maximum sessions software 10
associate application SCCP
dial-peer voice 1 pots
incoming called-number .
direct-inward-dial
dial-peer voice 10 pots
destination-pattern 112
no digit-strip
port 0/0/0:15
dial-peer voice 11 pots
destination-pattern 00[1-9]T
port 0/0/0:15
prefix 0
dial-peer voice 12 pots
translation-profile outgoing Prefix1-toCorpHQ-ANI
destination-pattern 000T
port 0/0/0:15
prefix 00
dial-peer voice 100 voip
description == Inbound/Outbound H323 PSTN GW From/To GK and CUCM Pub
translation-profile incoming Prefix0_InFrom_CUCM
destination-pattern 0207033...$
voice-class codec 1
session target ipv4:177.1.10.10
incoming called-number .
ip qos dscp cs3 signaling
dial-peer voice 101 voip
description == Outbound H323 PSTN GW To CUCM Sub
destination-pattern 0207033...$
voice-class codec 1
session target ipv4:177.1.10.20
ip qos dscp cs3 signaling
dial-peer hunt 1
telephony-service
max-ephones 1
max-dn 1
ip source-address 177.1.254.3 port 2000
max-conferences 8 gain -6
moh test.au
multicast moh 239.2.1.1 port 16384 route 177.1.254.3 177.3.11.1
transfer-system full-consult
create cnf-files version-stamp 7960 Sep 13 2013 18:55:27
line con 0
exec-timeout 0 0
line aux 0
line 66
no activation-character
no exec
transport preferred none
transport input all
transport output pad telnet rlogin lapb-ta mop udptn v120 ssh
line vty 0 4
login
scheduler allocate 20000 1000
ntp source Loopback0
ntp update-calendar
ntp server 177.1.254.1
end

Similar Messages

SCCM issue - "LANG_LIST has some locales which does not match with the locale of serial number"

I have a problem with the error "LANG_LIST has some locales which does not match with the locale of serial number" recurring.
I am trying to install Acrobat XI Std silently by SCCM.
I've used the Adobe Customisation Wizard to create a mst which include the volume serial number we have with our licence purchases. Note that I am in Australia. I use the command line in SCCM for the install as "msiexec /i "AcroStan.msi" TRANSFORMS="D&B_AcroStd.mst" /qn" which fails silently. If I install on a local machine using an admin command prompt and changing to /qb at the end, I get the aforementioned error.
I have a few things to try and resolve, having searched the adobe forums and other forums for the solution. The mst is only trying to install US English & I have even gone so far as to use the direct editor in the customisation wizard and change some values in the property table to resolve this. In the property table I can confirm that LANG_SEL_DEFAULT = ENU, REGIONAL_LIST = ENU, LANG_LIST = en_US, ProductLanguage = 1033
Is there a way to check the language specified for ym serial number?
Bryndon

Update on a couple of details:
@Sabian,
Thanks for the location, I've downloaded and then when I tried an install of the newly extracted msi (admittedly on the same computer) I got exactly the same issue. Of note though is that running /qf automatically brought up the same serial number and the same incorrectly spelled company name. Installing on another computer (freshly imaged) doesn't have those inputs already present under /qf. Next when I try using the transfrom (a new one) with /qr it gives an error of the serial number, displaying the entire serial.
@Sebastian
I've had a look through yours and it seems our issues could have the same origin. Looks like I may have to call customer support regarding the serial number as Sabian suggested in your thread.
The bit that gets me is when the same serial number is used in a manual install (or /qf) then it installs ok without any errors.

Setup.exe gives a "LANG_LIST has some locales which does not match with the locale of serial number"

I ran the Adobe Customization Wizard XI to create a transform file and now when run setup.exe it always come with the error "LANG_LIST has some locales which does not match with the locale of serial number".
It does the same thing when using msi with the command : msiexec /i AcroPro.msi TRANSFORMS=AcroPro.mst /qb!
Here is my setup.ini file
[Startup]
RequireOS=Windows XP
RequireMSI=3.1
RequireIE=7.0.0000.0
Require64BitVC10RT=1
CmdLine=/spb /rs /sl"1036"
[Product]
msi=AcroPro.msi
vcrtMsi=vc_red.msi
vcrtDir=VC10RT_x64
Languages=1033;1036
2052=Chinese Simplified
1028=Chinese Traditional
1029=Czech
1030=Danish
1043=Dutch (Netherlands)
1033=English (United States)
1035=Finnish
1036=French (France)
1031=German (Germany)
1038=Hungarian
1040=Italian (Italy)
1041=Japanese
1042=Korean
1044=Norwegian (Bokmal)
1045=Polish
1046=Portuguese (Brazil)
1049=Russian
1051=Slovak
1060=Slovenian
1034=Spanish (Traditional Sort)
1053=Swedish
1055=Turkish
1058=Ukrainian
1025=English with Arabic support
1037=English with Hebrew support
6156=French (Morocco)
CmdLine=TRANSFORMS="AcroPro.mst"
[Windows XP]
PlatformID=2
MajorVersion=5
MinorVersion=1
ServicePackMajor=3
[MSI Updater]
Path=WindowsInstaller-KB893803-v2-x86.exe
I don't know what goes wrong as took my serial number on my profile from the adobe web site, same thing for the download of the software.
Does it means that the serial number provided was invalid for deploying ?
NB.: My goal is to deploy our Acrobat XI through SCCM in silent mode and I don't know if there is extra consideration for that. For now it's only not working at the command line.
Another important point is that the install works great without customization ! If I just run the setup.exe from freshly extracted files and I use my serial number, everything is working fine.
So what goes wrong ?

Thanks for the reply brogers_1 and Vinod Dbhal, you gave good hint.
I retried installing the initial package in French on a Windows 7 English and the software installed properly in French.
As I used to work with virtuals for those tests, I rolled back my virtual and redo my test installation with chosing to install it in English on my Windows 7 English and again the installation finished properly but I was surprised when I realized that even if I chose English as language, the software was running in French !
Of course I can change the language settings (in the edit-preferences-language) to follow the operating system witch is nice.
That gave me the cue I needed to know. I started from scratch my customization with choosing only the French language in the "Application Languages" and I left the MUI Languages blank and saved the .mst
I ran again the same command : msiexec /i AcroPro.msi TRANSFORMS=AcroPro.mst /qb!
And everything works fine.
NB.: As I used the .msi directly, of course I had to install the prerequirement Visual C++ 2010 first. Otherwise the installation failed without any error message.
Thanks again to you for your good hint,
Bob

I am having trouble printing I have a connection to my printer wirelessly but does not print out the correct page I want.When I do print I get a bunch of pages more than is needed and also get a code and symbols please help I am jammed at work

I am having trouble printing I have a connection to my printer wirelessly but does not print out the correct page I want.When I do print I get a bunch of pages more than is needed and also get a code and symbols please help I am jammed at work

This can be the result of selecting the wrong driver. An older, unsupported laser printer will sometimes work with the generic Postscript driver.

HT4976 I have followed instructions to include a second keyboard for emoticons while texting on my Ipad. It does not bring out the second keyboard nor the "globe" to be typed????

Caan someon help me find the way to be able to see the second keyboard on my texting while using Ipad?
I have followed instructions and so I have open a second keyboard for emoticons but the "globe" would not show and therefore the emoticons would not appear.

i didn't read a lot of your 2nd paragraph, but it seems like the password is the issue, right?
do a true clean install
reboot your machine and hold down command+option+r, you should see a spinning globe - if you don't see the globe or anything that reads internet recovery, shut down and try again
at menu, chose disk utility and once there, find your HD on the left side, select the physical name and erase it as mac journaled
exit disk utlity
at menu, choose install OSX
this time, when it asks for a password just hit continue, it will let you complete without a password
you should be able to get into your laptop, now figure out what password you'll be able to use with your kb issue

BADI ME_PROCESS_PO_CUST - DOES NOT CLEAR OUT ERROR

In ME21N I want to validate the field Commodity Code - STAWN. I have used the BADI ME_PROCESS_PO_CUST*
. Have used get_foreign_trade() in the PROCESS_ITEM method . I am able to throw an error . It is doing it but*
after throwing error then when we give a valid Commoditycode too it is still showing the error and not clearing the error .*
As suggested by Dean Q I used INCLUDE mm_messages_mac,
tried im_item->set_foreign_trade( ls_mepo_eipo) still when a valid Commodity code is entered after an invalid one it does not clear out the error. In fact on checking using break-point I found that the second time it does not enter into the method PROCESS_ITEM. Any help is welcome
Nivedita

Hi,
In SE18 give ME_PROCESS_PO_CUST as the enhancement spot and display. At the left side of the screen you can see the badi definition ME_PROCESS_PO_CUST. Expand the tree and double click on implementations. You can see the enhance implementations created. Double click on the enhancement implementation and in that screen there is a check box 'Implementation is active' and field 'Effect in current client'.
If you know the enhancement implementation name(not the badi implementation name), you can check it directly from se19.
Regards,
Poornima

System.out.println does not print out anything

I'm wonder why the dos mode does not print out the System.out.println.
My code has:
import java.io.*;
import javax.servlet.*;
import javax.servlet.http.*;
public class test extends HttpServlet {
   public void doGet(HttpServletRequest request,
   HttpServletResponse response) throws IOException,
   ServletException {
      System.out.println("Hello");
The compilation is ok... but it does not display anything... how come?

"System.out.print()" prints to the log file of the tomcat server. in order to print on the screen use JspWriter.
import java.io.*;
import javax.servlet.*;
import javax.servlet.http.*;
public class test extends HttpServlet {
public void doGet(HttpServletRequest request,
HttpServletResponse response) throws IOException,
ServletException {
response.setContentType("text/html");
PrintWriter out = response.getWriter();
out.println("Hello");
//System.out.println("Hello");
Hope this helps!

Any ideas why the second HOST call does not work???

Hi Folks.
I have written the following code which works fine in all but one respect.
The code creates a zip file on a server (Accessed over a network) hence the full windows network path name.
The call to host on the server works in terms of running the zipinvoices.bat file and the zip file is generated on the server in the correct location.
The prigram unit also generates the correctly formatted mailinvoices.bat file. However, the second call to HOST does not run/execute the mailinvoices.bat file. If I go to the server and run the mailinvoices.bat file directly, it runs perfectly and emails the file to me, no problemo.
Why does the second call to HOST from the client machine not run?
Any clues anyone???
Cheers
Simon Gadd
PROCEDURE send_email_invoices_pu_p (p_organisation IN VARCHAR2) IS
v_processing_cycle          CHAR(4);
     v_alert_but                              NUMBER;
     v_error_num                              NUMBER;
     v_sent_status                     NUMBER(1);
v_stage                                        NUMBER(1);
v_year                                        VARCHAR2(4);
v_month                                        VARCHAR2(9);
v_folder_name                         VARCHAR2(25); -- Name of the file which holds the 'Printed' invoices in the receivables folder. v_organisation                    VARCHAR2(50);
v_password                              VARCHAR2(25);
v_organisation                    VARCHAR2(25);
     v_host_command                    VARCHAR2(100);
v_from_name                              VARCHAR2(100);
v_to_name                                   VARCHAR2(100);
v_subject                                   VARCHAR2(100);
v_error_txt                              VARCHAR2(200);
v_file                                        VARCHAR2(200);
v_message                                   VARCHAR2(500);
     v_line_buffer                         VARCHAR2(5000);
v_working                                   BOOLEAN := TRUE;
v_zipinvoices_bat               TEXT_IO.FILE_TYPE;
     v_mailinvoices_bat          TEXT_IO.FILE_TYPE;
     CURSOR c_sent_status IS
          SELECT sent
          FROM INVOICE_EMAIL
          WHERE UPPER(ORGANISATION) = UPPER(v_organisation);
     CURSOR c_select_folder IS
          SELECT folder
          FROM INVOICE_EMAIL
          WHERE UPPER(ORGANISATION) = UPPER(v_organisation);
CURSOR c_select_email_elements IS
SELECT      send_to,
                    send_from
FROM INVOICE_EMAIL
          WHERE UPPER(ORGANISATION) = UPPER(v_organisation);
BEGIN
v_organisation := p_organisation;
-- Check to see if the invoices have already been e-mailed for this Procssing Cycle. If they have,
-- then warn the user of this and get them to confirm that they wish to proceed and e-mail them again.
-- The batch e-mail process will re-zip the invoices (ignoring a pre existing .zip file) and overwrite
-- the existing zip file if it exists or generate it if it does not exist.
     OPEN c_sent_status;
          FETCH c_sent_status INTO v_sent_status;
     CLOSE c_sent_status;
     IF v_sent_status = 1 THEN
          v_alert_but := SHOW_ALERT('SEND_AGAIN_ALRT');
               IF v_alert_but = ALERT_BUTTON2 THEN RAISE FORM_TRIGGER_FAILURE;
                    ELSE NULL;
               END IF;
     END IF;
:CONTROL.WORKING := 'Started Zipping invoices for '||INITCAP(v_organisation)||'.'||CHR(10)||'Please wait..';
SYNCHRONIZE;
-- The following code opens the zipinvoices.bat file which resides in the root folder \\Ebony\c$\FCSS\DB_SCRIPTS\ and modifies it ready to
-- zip up the invoices in the relevant organisation's invoice folder for the current processing cycle.
v_processing_cycle := GET_CURRENT_TRAFFIC_PERIOD;
v_month := RTRIM(INITCAP(TO_CHAR(TO_DATE(v_processing_cycle, 'MMYY'), 'MONTH')));
v_year := (TO_CHAR(TO_DATE(v_processing_cycle, 'MMYY'), 'YYYY'));
     OPEN c_select_folder;
     FETCH c_select_folder INTO v_folder_name;
     CLOSE c_select_folder;
KILL_OLD_ZIP_PU_P('del \\Ebony\c$\FCSS\CYCLE_DATA\'||v_processing_cycle||'\receivables\'||v_folder_name||'\invoices.zip');
SELECT zip_password
INTO v_password
FROM INVOICE_EMAIL
WHERE UPPER(ORGANISATION) = UPPER(v_organisation);
v_zipinvoices_bat := TEXT_IO.FOPEN('\\Ebony\c$\FCSS\DB_SCRIPTS\zipinvoices.bat', 'w');
v_line_buffer := 'cd..';
TEXT_IO.PUT_LINE (v_zipinvoices_bat, v_line_buffer);
v_line_buffer := 'cd..';
TEXT_IO.PUT_LINE (v_zipinvoices_bat, v_line_buffer);
v_line_buffer := 'wzzip -s'||v_password||' -x*.zip -ybc \\Ebony\c$\FCSS\CYCLE_DATA\'||v_processing_cycle||'\receivables\'||v_folder_name||'\invoices \\Ebony\c$\FCSS\CYCLE_DATA\'||v_processing_cycle||'\receivables\'||v_folder_name||'\*.*';
TEXT_IO.PUT_LINE (v_zipinvoices_bat, v_line_buffer);
v_line_buffer := 'exit';
TEXT_IO.PUT_LINE (v_zipinvoices_bat, v_line_buffer);
TEXT_IO.FCLOSE (v_zipinvoices_bat);
-- The following code executes the freshly edited \\Ebony\c$\FCSS\DB_SCRIPTS\zipinvoices.bat file to produce the zipped invoices file
-- ready to be e-mailed out to the address specified in the INVOICE_EMAIL table for the relevant organisation.
v_host_command := '\\Ebony\c$\FCSS\DB_SCRIPTS\zipinvoices.bat';
v_stage := 1;
HOST (v_host_command, NO_SCREEN);
IF NOT Form_Success THEN
     IF v_stage = 1 THEN
     :CONTROL.WORKING := 'Error -- The .zip file for '||INITCAP(v_organisation)||' was not produced.';
          SYNCHRONIZE;
     ELSIF v_STAGE = 2 THEN
     :CONTROL.WORKING := 'Error -- The zipped invoices file for '||INITCAP(v_organisation)||' was not emailed.';
          SYNCHRONIZE;
          END IF;
ELSE NULL;
END IF;
:CONTROL.WORKING := 'All invoices for '||INITCAP(v_organisation)||' successfully zipped.'||CHR(10)||'Attempting to send via e-mail.'||CHR(10)||'Please wait..';
SYNCHRONIZE;
-- The following code e-mails the freshly created .zip file for the relevant organisation and e-mails it to the
-- recipient specified in the relevant row in the INVOICE_EMAIL programme along with from address, subject and
-- message if specified.
OPEN c_select_email_elements;
FETCH c_select_email_elements INTO
v_to_name,
v_from_name;
CLOSE c_select_email_elements;
v_stage := 2;
v_mailinvoices_bat := TEXT_IO.FOPEN('\\Ebony\c$\FCSS\DB_SCRIPTS\mailinvoices.bat', 'w');
v_line_buffer := 'cd..';
TEXT_IO.PUT_LINE (v_mailinvoices_bat, v_line_buffer);
v_line_buffer := 'cd..';
TEXT_IO.PUT_LINE (v_mailinvoices_bat, v_line_buffer);
v_line_buffer := 'clemail -quiet -smtpserver mailhost.0800dial.com -smtpport 25 -to '||v_to_name||' -from '||v_from_name||' -subject "'||v_month||' '||v_year||' Roaming Traffic Invoices from United Clearing Ltd" -bodyfile \\Ebony\c$\FCSS\DB_SCRIPTS\invoice_body.txt -attach \\Ebony\c$\FCSS\CYCLE_DATA\'||v_processing_cycle||'\receivables\'||v_folder_name||'\invoices.zip';
TEXT_IO.PUT_LINE (v_mailinvoices_bat, v_line_buffer);
v_line_buffer := 'exit';
TEXT_IO.PUT_LINE (v_mailinvoices_bat, v_line_buffer);
TEXT_IO.FCLOSE (v_mailinvoices_bat);
v_host_command := '\\Ebony\c$\FCSS\DB_SCRIPTS\mailinvoices.bat';
HOST (v_host_command, NO_SCREEN);
IF NOT Form_Success THEN
     IF v_stage = 1 THEN
     :CONTROL.WORKING := 'Error -- The .zip file for '||INITCAP(v_organisation)||' was not produced.';
          SYNCHRONIZE;
     ELSIF v_STAGE = 2 THEN
     :CONTROL.WORKING := 'Error -- The zipped invoices file for '||INITCAP(v_organisation)||' was not emailed.';
          SYNCHRONIZE;
          END IF;
ELSE NULL;
END IF;
UPDATE INVOICE_EMAIL
     SET sent = 1
          WHERE UPPER(ORGANISATION) = UPPER(v_organisation);
COMMIT;
GO_BLOCK ('INVOICE_EMAIL');
EXECUTE_QUERY;
:CONTROL.WORKING := 'Please press a button on the left to e-mail invoices to the organisations listed.';
SYNCHRONIZE;
EXCEPTION
     WHEN OTHERS THEN
          v_error_num := SQLCODE;
          v_error_txt := SUBSTR(SQLERRM, 1, 200);
          MESSAGE('The error was: '||v_error_txt||' and the code was: '||v_error_num);
          RAISE FORM_TRIGGER_FAILURE;
END;

As a suggestion I'd put the Text_io segments into their own begin - exception - end sub-blocks within the main code. This way if Text_io does raise an exception you can catch it earlier as it may be able to recover - That is if it is a text_io exception.
Other than that you;ll have to step through in Debug.

My iphone 6 connects to the car via bluetooth, the music works good, but the phone calles does not work. It looks like it is working but doesn't. I have tried in my Hyundai and a Dodge rent car and get the same results. I updated the last 8.0.2.

My iphone 6 connects to the car via bluetooth, the music works good, but the phone calls does not work. It looks like it is working but doesn't. I have tried in my Hyundai Sonata and a Dodge Dart rent car and get the same results. I updated the last 8.0.2. It worked the first day i had the phone, and then i updated to Ios 8.0.2 and it quit working.
Now when i get in the car, it acts like it is connected and makes the same call it was on after syncing to bluetooth, but it really isn't on a call. This is happening on both cars.
Does anyone know if this is the phone and i need to take it to Apple or if there is an issue that Apple is working on getting a fix for?
My son in law has the exact same phone as me, we both got the on 10/6, he had a Dodge Dart and his is working via bluetooth.
Someone HELP please, as i consider this a safety issue by not having my calls go to bluetooth.

We had the same problem, but figure out the solution.
You MUST have at least 1 song added to your ITUNE! After you add a free song, then everything else should work as normal!
Hope this helps!

My iphone 4 does not register calls made to it. if i make a call from another phone, i can hear it ringing, but it does not register on the iphone. also, i do not get any messages when this happens. then after a day or two it decides to start working.

My iphone 4 does not register calls made to it. if i make a call from another phone, i can hear it ringing, but it does not register on the iphone. also, i do not get any messages when this happens. then after a day or two it decides to start working.

Clean iPhone charging port with clean dry toothbrush. See if better. If still problem clean charging port again with toothbrush and small amount of Isopropyl Alcohol.

I've found two bugs in iOS 7. 1) declined calls does not appear as missed calls on the lock screen/notification centre. 2) when bluetooth is enabled from control center, it does not connect to an already paired bluetooth device

I've found two bugs in iOS 7:
1) declined calls does not appear as missed calls on the lock screen/notification centre - iOS 7.0.2.
2) when bluetooth is enabled from control center, it does not connect to an already paired bluetooth device automatically - iOS 7.0.

We are all users here, just like you, but you can tell Apple about it by using this link:
Apple - iPhone - Feedback

How do I remove my caller id from my samsung convoy phone so that the person I call does not see my name?

How do I remove my caller id from my samsung convoy phone so that the person I call does not see my name?

MojaveMoon's solution will work if there is only one person you want to block your ID from; if you want to block your caller ID from everyone, you can go to your account online, go to Change Features, and scroll down till you see Caller ID block. Instructions say that once this is activated, you can dial *82 before any # you WANT to display your number to, but all others will be blocked.
If you are on a Family share plan, the account owner needs to log in and choose your line to activate this feature.

I need to reset my security questions, I don't have a rescue email and I live in Lebanon (Does not appear in the list of countries for apple calls)

Hi,
I forgot my security questions and I don't have a rescue email setup.
I serached the internet and the only solution I found for that is to call apple. The proble is there is no phone to call, they have to call you and there is a list of countries.
I live in Lebanon and it does not appear in the list of countries listed for apple customer support call.
How can I reset the security questions.
thank you

The Three Best Alternatives for Security Questions and Rescue Mail
    1. Use Apple's Express Lane.
          Go to https://expresslane.apple.com ; click 'See all products and services' at the
          bottom of the page. In the next page click 'More Products and Services, then
          'Apple ID'. In the next page select 'Other Apple ID Topics' then 'Forgotten Apple
          ID security questions' and click 'Continue'.
     2. Call Apple Support in your country: Customer Service: Contact Apple support.
     3. Rescue email address and how to reset Apple ID security questions.
A substitute for using the security questions is to use 2-step verification:
Two-step verification FAQ Get answers to frequently asked questions about two-step verification for Apple ID.

Does anyone know how well the Intel Iris Pro installed on new 15" MacBook Pros performs using Photoshop and Lightroom. I have seen some differing opinions out there, and I would rather not shell out the extra cash for the Nvidia if I don't have to. I most

Does anyone know how well the Intel Iris Pro installed on new 15" MacBook Pros performs using Photoshop and Lightroom? I have seen some differing opinions out there, and I would rather not shell out the extra cash for the Nvidia if I don't have to. I mostly do photo editing for business and personal use. I have not used the 3D function in Photoshop, but I would like to know that I could.

You could download a trial and see how well it works before committing to a subscription. You get 30 days to decide.
Photo editor | Download free Adobe Photoshop CC trial
Photo editor app | Download free Adobe Photoshop Lightroom 5 trial
Gene

Having a MBPr late 2013 and having a sound problem the sound does not come tom the headphones even its all the way up and when i remove the headphones it docent come out the internal speaker either ? any idea how i fix this?

the sound do not come out the headphones sometimes altho its all the way up in the setting and when i remove the headphones the sound doesnt come from the internal speaker either and only a reboot fixes the problem and thats annoying! any idea how tto fix this?

Hello. I've been able to play sound without problems through headphones or external speakers to date - the output always switched to these automatically until today. Now, sound output continues through internal speakers even if I plug in headphones or external speakers.
- I tested the headphones and speakers on other devices: they work fine.
- When I plug in headphones or speakers into the audio output port (I have verified that I'm not using the input jack) the devices are not detected and are not listed under the output tab in system preferences-sound.
I concluded from this that I probably had a problem with the audio port, so to test that I tried the following. I plugged a powered multi-USB device with ports for microphone line-in and headphone line-out into the USB port and switched it on. I verified that it was working by plugging a USB stick into the multi-USB device - this was recognised successfully, so the device was clearly working. I then plugged in headphones and speakers into the audio line-out on the multi USB device - but still no sound came through them (and tey were not listed among output devices) and the Mac continued using internal speakers.
What should I do? Does the latter test suggest that the problem does not lie with the audio port, or is my test not conclusive? What would you advise?
Many thanks indeed!
NG

CALL DOES NOT ROUTE OUT THE LOCAL GATEWAY

Similar Messages

Maybe you are looking for