Can I use third party Windows CE based touch panel to control my system?

I want to use a WindowsCE based touch panel to control my system by connecting a CompactDAQ to it through USB and installing the.exe file built from LabVIEW and installing the CompactDAQ drivers.
It sounds doable, but I don't know if WindowsCE does support those .exe files or the hardware drivers or if there is something I can do to make it support them. I hope anyone has an idea about this and can help me.
Thank you
Solved!
Go to Solution.

I found the following statement at :
LabVIEW Touch Panel Module Getting Started Guide
http://zone.ni.com/devzone/cda/tut/p/id/5868
"The deployment procedures discussed previously for NI touch panels are not guaranteed to work for third party touch panels. If the use of a third-party touch panel is desired it must met certain requirements in order for the LabVIEW touch panel module to properly work with it.
The LabVIEW Touch Panel module only officially supports the two operating systems and two processors that the NI touch panel devices are based on. The operating systems supported are Windows CE 4.2/5.0 and Windows XP Embedded, while the supported processors include the StrongARM, XScale, and x86.
Another consideration when using a third-party touch panel is that a LabVIEW Touch Panel Deployment License must be purchased for each deployment of an application developed with the LabVIEW Touch Panel module.
In addition, specific Microsoft tools must be installed on the touch panel target in order for the LabVIEW Touch Panel application to function as expected. The following Microsoft eMbedded Visual Tools need to be installed:
Microsoft eMbedded Visual C++ 4.0
Microsoft eMbedded Visual C++ SP 4 or later
SDK for Windows Mobile 2003-based Pocket PCs
Reference the Where Can I Find the Microsoft Tools I Need for the LabVIEW Touch Panel Module? knowledge base article to find links to the current Microsoft download sites."
Kareem W.
National Instruments
Web Product Manager

Similar Messages

Error installing NI TPC Service on a 3rd party windows XPe Based Touch Panel

Hi,
First of all sorry for my English.
I'm having trouble when i try to install NI TPC SERVICE on a 3rd party Touch Panel that runs Windows XPe (Embedded).
I have tried lot of time. I'm installing the msi application for XPe from the folder "NI_TP_Service" of the Installation Path for LabVIEW 8.6 Touch Panel Module.
The installer file hungs after installing the service and just when it tries to initialize it and I get a Error Windows that says "Error 1920. Service 'NI TPC Service' (NITPCService) falied to start. Verify that you have sufficient privileges to start system services."
I'm logged as Administrator, and I don't know what to do.
If anyone know what can i do I'll be pleased in hearing the answer.
Regards

Hi AlexDarsigny,
You will need either the Touch Panel Module or the Datalogging and Supervisory Control Module (DSC). Either of these modules will allow you to deploy and install NI software to your touch panel. They also include many other features for developing those applications. You will also need a deployment license for any non-NI touch panel that you plan on deploying the applications to. The other software needed on the touch panel itself will include the LabVIEW Run-Time Engine and the NI TPC Service. The following link has some information on this:
http://zone.ni.com/reference/en-XX/help/371618H-01/lvxpe/tpc_install_tpc_srvc/
Once deployed, the program will run as a stand-alone application that can be started from the HMI itself. Of course this depends on the functionality you create within the application, just like you would for any standard LabVIEW application.
David C

Can we Monitor third party Windows servers through Cisco Prime

Hi Team,
We are using Cisco Prime assurance and are currently monitoring Cisco UCCE Components through it.
Meanwhile we have few third party windows servers , which we would like to monitor it through Cisco Prime , just to maintain a single monitoring tool.
If yes, please share the steps or link.Also highlight the limitations in that.
Regards,
krishna

Seems Cisco Prime Assurance Manager is now obsolete and end of life already.
It is replaced by Cisco Prime Infrastructure. CPI supports third party/vendor devices to some minimum extent with limited management details collected via SNMP Templates.
-Thanks
Vinod
**Encourage Contributors. RATE Them.**

Can I use third party DAQ boards with Labview real time?

I have an Adlink DAQ 2010 card that I curently use with labview. Will this card also work with Labview real time? What requironments are there for 3rd party cards to work with Labview real time?
Thanks!

Hello George,
Here is a great link for you to take a look at: Can I Use a Third-Party Device with LabVIEW RT?
Have a great day,
NathanT

Can't use third-party earphones

Does anyone have problems using a third-party earphone? I tried using my Bose earphones and Sony earphones which are supposed to work with the I-Phone, but no luck. The earphones that came with the I-Phone works.

you most likely need the adapter.
here is a link: http://store.apple.com/1-800-MY-APPLE/WebObjects/AppleStore.woa/wa/RSLID?mco=3DB 4EB78&fnode=home/shopiphone/iphone_accessories/cablesdocks&nplm=TN546LL/A
there is apples to but there's is $20: http://store.apple.com/1-800-MY-APPLE/WebObjects/AppleStore.woa/wa/RSLID?mco=B19 14140&fnode=home/shopiphone/iphone_accessories/cablesdocks&nplm=MA854LL/A
Message was edited by: edden amber

Can I use third party web services that communicate via http-post with webui builder?

Hi,
I have 5 computers (services) that are controlled via http-post. 3 of these services are implemented as labview webservices, 1 is labview socket (with python http-wrapper) and the last one is implemented with c# (lighttpd + cgi).
Can I use webui builder to controll all of them? Or, what is the simplest change so I can use webui builder?
What I would like to do, is to change the current javascript-UI to labview-webui. For the interfaces implemented with labview webservices, this is not a problem. For non-labview services, I don't know if it is even possible.
br,
Juha

To add to Mike's answer, the only caveat is that the server needs an appropriate clientaccesspolicy.xml file at the root level (http://yourserver/clientaccesspolicy.xml), or a completely open crossdomain.xml file, for the editor and built apps to be able to communicate with it. There's a help topic which explains this in the context of LV web services, but it's true for Web UI Builder to be able to communicate with arbitrary web servers also.
Since it sounds like you control all the web servers in question, it shouldn't be too difficult to get this file in place, though.

How can i telnet or get access to other LAN members in LAN without using third party software?

I have admin access to the main router in our LAN, so how can i telnet or get access to other LAN members in LAN without using third party software?
its linksys3500 router and i login as admin using the gateway address in address bar..
i want to access the c drive of my colleague in same subnet in same office and i know his ip address.but he not configured telnet accept request.so without it how can i open his telnet port and access him

I think you are using the wrong terminology. You can browse the hidden share of any pc if you know the ip and have a valid user account on the pc by typing in the following \\computername\c$ or \\ipaddress\c$ . It should prompt you for a user account. You may have to allow this through the windows firewall (or disable it completely).

I have admin access to the main router in our LAN, so how can i telnet or get access to other LAN members in LAN without using third party software?

I have admin access to the main router in our LAN, so how can i telnet or get access to other LAN members in LAN without using third party software?
its linksys3500 router and i login as admin using the gateway address in address bar..
i want to access the c drive of my colleague in same subnet in same office and i know his ip address.but he not configured telnet accept request.so without it how can i open his telnet port and access him

Duplicate post.

Support for Shared Variables in Third Party XP embedded based TPC's?

I have deployed an application in an XP embedded based Touch Panel (Third party). The application is working fine, but the shared variables hosted on an RT (sbRIO Board) are not getting updated in the application on TPC
1. The TPC is part of the project as Windows XP Embedded Touch Panel
2. NI TPC Service has been installed on the TPC and the application can be deployed remotely from the development PC through ethernet. (Hence network connections and communications are OK)
3. By using Distributed Systems Manager in the development computer, I can see that the shared variables are getting updated on the network
I believe that the problem can be solved if the following programs are installed on the TPC
A. Support for shared variables for XPembedded
B. Shared Variable engine
I have tried installing support for shared variables from Program Files > National Instruments > Labview 8.6 > PDA > Utilities > Variables > x86 - but am getting an installation error "Unable to find application manager for Pocket PC applications".
Shared variable engine has been installed from ve220 folder. The program is getting installed. But the Variable Engine is not started Control Panel > Administrative tools > Services in Xpe, the service is stopped and cannot be started. When I try to start the service, I am getting the following error on TPC
"Could not start the National Instruments Variable Engine Service on the local computer.
Error 1053. The service did not respond to the start or control request in a timely fashion."
Please suggest solutions for the above or alternate locations for the following:
1. Support for shared variables for XP embedded TPC's
2. Shared Variable engine installer program.
Thanks
Krish
Solved!
Go to Solution.

Problem solved!
Update for interested folks working on XP Embedded TPC's
Just to make sure that Shared Variables were indeed accessible to the TPC, I wanted to install Distributed Systems Manager 8.6 on the TPC. However since the TPC was having only 1 GB of DOM (Disk on Memory) and with all the software I had tried, there were only a few Megabytes left on the system. I had to add another DOM of 2 GB.
All the products of the Installation went fine, with the exception of NI Logos (Version 5.0). NI Logos installation failed repeatedly. I tried installing NI Logos separately, with the same results. Then I had this gut feeling that NI Logos had something to do with the issue.
I then downloaded the new version of NI DSM 2009 SP1. Although this was supposed to get installed on any fresh system without Labview, the installation would not proceed beyond the setup stage. I tried installing NI Logos from the products folder on the new download separately and it worked like magic!
Once the new Logos (Ver 5.5) got installed, the Shared Variable Engine started automatically and the Shared Variables were finally unleashed - free to rise and shine! Thank God Almighty!!
On the lighter side, come to think of it - for running an application of around 400KB, we need XP embedded, NI Run Time, Logos, DSM .......... (all around 900MB). Can we make it any simpler?!! Inviting your comments .......
Thanks
Krish

FCE Support of Third-Party Plug-ins based on FxPlug - iSight

I wish apple would make FCE Support of Third-Party Plug-ins based on FxPlug.
I would love to be able to record to FCE with the iSight plug-in from Noise Industries....
Is there an other way to do this??? Record audio and video to a quicktime movie from my iMac???
thanks for your reply...
G5 Mac OS X (10.4.9)

You can capture using the QuickTime player.

Extending wireless LAN using third-party devices?

I know that with multiple Airport Extreme base stations, it’s a simple matter to extend the range of an 802.11n network by using the “Extend a wireless network” or “Participate in a WDS network” wireless modes. It seems like of the two, “Extend a wireless network” might be the easier of the two to configure. Does anyone have recommendations / preferences between the two modes?
Separately, although I can afford Airport Extreme stations personally, I have friends with the same desire to extend their existing wireless network but who can’t afford Airport Extreme stations. Is there a lower-cost way to do this with Netgear, D-Link, or other third-party devices? Does this mean all of the devices must support WDS to work, or are there other solutions? Do you have recommendations for specific models that work well for extending networks (preferrably also models that support WPA/WPA2, and not just WEP).
Any help would be appreciated. I won’t go into the details of the distances involved or intervening walls. Let’s just say a hop or two should stretch the distance.

Bob Timmons wrote:
"Extend a wireless network runs at "n" wireless speeds with minimal bandwidth loss on the network
WDS runs at "g" wireless speeds, even if you are using newer "n" devices. The bandwidth on the entire wireless network is cut in half for each "remote" added to the network. So, with one "remote" in a WDS, you have a "g" wireless network running at 1/2 speed. If you have two "remotes" in a WDS, you have a "g" wireless network running at 1/4 speed.
Bob — thank you so much for the help.
Years ago in the days when Airport Extreme base stations supported 802.11b/g only, I remember setting up a WDS network between three Airport Extreme base stations. I seem to remember that the one in the middle was set up in a “relay” mode to bridge between the two remote base stations. In theory, using multiple relays, you could extend a network arbitrarily far as long as you could get power to all the devices and didn’t care about all sorts of bandwidth, latency, and signal strength hits.
Is it the case that with the 802.11n in current Airport Extreme stations you can't set up relays in a similar fashion using the "Extend a Network" wireless mode? I was looking at Apple’s “Designing Airport Networks Using Airport Utility” document, which doesn’t explicitly say, but seems to suggest that the central base station (operating in “Create a Wireless Network” mode) can be extended if the “allow this network to be extended” button is set, and then on a second base station you can use the “Extend a Wireless Network” mode to extend it. However, there’s nothing to suggest that you could extend off the second base station. Does anyone know if that’s possible?
I was looking at Netgear-brand wireless extenders this morning (http://www.netgear.com/home/products/wireless-range-extenders/wireless-range-ext enders/default.aspx) which sell for around $75 to $80 each online. They can extend any 802.11b/g/n network if the remote device supports the WPS (Wireless Protected System) standard, as most Netgear products appear to do (I believe Airport Extreme base stations don’t support WPS). They make it quite easy to connect Netgear wireless devices using “Push ’N’ Connect” buttons on the devices.
However, Netgear pre-sales specialist pointed out that the Netgear wireless extenders (the WN2000RPT is the current model) can similarly only extend out by one hop from the “center” and cannot operate as relay to get out further, as would be the case for WDS-based relays.
Is it the case that you need to find devices that support WDS (Wireless Distributed System) to allow for multiple relays to cover longer distances? I know that Airport Extreme base stations, both current models and the older b/g models, support WDS. Can anyone recommend third-party WDS-capable wireless modems or access points?
Any help would be appreciated.

How to use third party library (like .dll and .lib files) in flascc?

I have a number of .dll and .lib files of the third party library, which are generated from C++ code.
I read about flascc on other web site says:
"If you want to use third party library in your Flascc project,you must have either the source code or the linkable file which is compiled of the third party library "
Dose the linkable file mean .dll file or .lib file?
AND
How can I use the fuctions in them in my flascc project.?

Native code is not interchangeable between platform.
It means that you can't use library that wasn't build specifically for flascc.
And when they say linkable files they mean libraries compiled for flascc, not any libraries.
So if your libs are for windows, no luck, you have to recompile everything

How to do XMLDSig using third-party JCA providers?

Hi all,
Can anyone please let me know how to do XMLDSig using third-party JCA providers? The Sun XMLDsig documentation says that "A JSR 105 implementation SHOULD use underlying JCA engine classes, such as java.security.Signature and java.security.MessageDigest to perform cryptographic operations", but it doesn't say how to define the JCA provider programmatically. I don't want to change the Providers order in the security.properties file.
Do we need to make any changes in the JCA provider classes to work with XMLDSig and XML encrypt?
I'd appreciate your help.
Joe

How to identify whether the third party app has registered URL scheme or not. I also send a request mail to the third party app developers regarding URL scheme, but there is no reply from them.

Convert word document in PDF,e pub,by using third party dll in Sharepoint designer workflow 2013?

Hi,
I want to convert word document to PDF, EPub, by using third party (.dll).
In SharePoint designer workflow in 2013.
So that I have question, Can we Install third party (.dll) in SharePoint workflow Designer for conversion?
Means I have created one simple application conversion of word to e Pub, PDF, Image by using (Spire.doc dll) in Visual Studio.
So this same conversion I want to work in SharePoint designer workflows?
So anybody has any solution then please provide me.
Thanks,
Samadhan

it might be worth looking at these CodePlex steps, that plug directly into the Word Automation Services.
http://sp2010wordautomation.codeplex.com/
It'll provide you with a configurable step like the below that should help you achieve your aims
Steven Andrews
SharePoint Business Analyst: LiveNation Entertainment
Blog: baron72.wordpress.com
Twitter: Follow @backpackerd00d
My Wiki Articles:
CodePlex Corner Series
Please remember to mark your question as "answered" if this solves (or helps) your problem.

Security settings change when rendered from third party Windows 2008 R2 server

We created a fillable PDF form in Adobe Acrobat and made it Reader extended. Opening the form on a local hard drive the security settings show that Signing: is Allowed. We can sign documents in the form with a signature pad.
After we upload it to a third party Windows server 2008 R2, and we later go to access the form, the server renders it back to us in Adobe Reader. We are unable to digitally sign documents in the form with a Topaz signature pad. We notice that although the form was originally created with the form being Reader extended the security settings change to Signing: Not Allowed.
How can we get the server to render the document back to us where we can digitally sign documents in the form?

The second file still shows the extended rights header is present (it's warning you about restrictions at the top of the dialog while also reporting the method is "no security") but the digital signature which grants those extended rights will be invalidated if *anything* in the file structure is changed. I suspect in this case that the server software is doing something to your file; it may be trivial such as adding an XMP tag, but it's enough to break the hash check.

Can I use third party Windows CE based touch panel to control my system?

Similar Messages

Maybe you are looking for