Can MPLS aware Netflow ver. 9 be enabled on the catalyst switches 6500

HI, I'm working for KOREA TELECOM, and currently providing MPLS VPN.
We're planning to provide our customer with traffic report using NetFlow..
I read some documents which reads Netflow ver.9 can be enabled on Cisco GSR 12000 Series, but no mention about catalyst switches. So, I ' m curious about that Netflow ver 9 can be activated on catalyst 6500 series.. because the point where switch is located already have mpls encapsulated packet ( mpls vpn packet).
Thank you , in advance.

NetFlow is now integral to Cisco 6500. A configuration we recommend is as below:
mls netflow     // This enables NetFlow on the Supervisor.
mls nde sender version 7
mls aging long 64  // This breaks up long-lived flows into (roughly) one-minute segments.
mls aging normal 32  // This ensures that flows that have finished are exported in a timely manner.
mls flow ip interface-full
mls nde interface
The  next two commands will help to enable NetFlow data export for  bridged  traffic which is optional. You can specify the list of VLANs  here to  enable bridged traffic.
ip flow ingress layer2-switched vlan
ip flow export layer2-switched vlan
Apart from this, NetFlow has to be enabled on the MSFC using the below commands.
ip flow egress       // This command has to be executed on all the L3/VLAN interfaces.
ip flow-export destination {hostname|ip_address} 9996  // The hostname or IP address of the flow server
ip flow-export source {interface} // The interface through which NetFlow packets are exported. eg: Loopback0
ip flow-export version 9
ip flow-cache timeout active 1
snmp-server ifindex persist
The new Cisco Flexible NetFlow actually allows for export of MPLS specific information (I believe it is stack lables) in addition to information on IP Address, port, etc. But you will need a tool that can support these additional fields. Otherwise you can view IP, port, protocol, etc related information from MPLS links.
Regards,
Don Thomas Jacob
ManageEngine NetFlow Analyzer

Similar Messages

  • MPLS-Aware Netflow support on some GSR Eth linecards

    Does anyone know if the following linecards will support MPLS-aware Netflow?
    The platform is a GSR 12410 with PRP-1 running IOS 12.0(32)SY1 (this release do sopport MPLS-Aware Netflow)
    * 4GE-SFP-LC 4 Port ISE Gigabit Ethernet
    * SPA-2X1GE 2-port Gigabit Ethernet Shared Port Adapter (on SIP-401)
    * SPA-8XE1FE-TX-V2 8-port Fast Ethernet TX Shared Port Adapter (on SIP-401)
    Which of those is considered as "Modular GE"? ("Modular GE" interfaces have some limitations in the feature MPLS-aware Netflow)
    Thanks in advance
    Gustavo Paz
    Systems Engineer at Softnet Logicalis

    Both the SIP -401 will support MPLS aware net flow as they support V9 except for the Gig ISE which I believe doesnt.
    Also find a Netflow Solutions Guide for Reference:
    http://www.cisco.com/en/US/products/sw/netmgtsw/ps1964/products_implementation_design_guide09186a00800d6a11.html
    SIP 401 DataSheet
    http://www.cisco.com/en/US/products/hw/routers/ps167/products_data_sheet0900aecd80465682.html
    Gig ISE Data Sheet
    http://www.cisco.com/en/US/products/hw/routers/ps167/products_data_sheet0900aecd803f856f.html

  • Can I use InDesign Ver 3.0 and the PM plug in pack with Vista?

    I am a long time Pagemaker user and am still using PM6.5   I needed a new computer and of course, it is the Vista OS.  I have an original version of InDesign CS (Ver 3.0) with the Pagemaker plug in pack.  I never learned to use it cause I was so used to 6.5.  Anyway, I installed the InDesign on my new Vista computer but it won't install the PageMaker plug in pack.  Says that the OS doesn't support the installation.  Can anybody tell me if there is a fix for this or how I can get this to work.  InDesign seems to hard and I have thousands of old PM6.5 files I need to use.  Thanks!

    OK well im using vista 64 bit ...and everything the so called community experts  say  means i should not be able to install this  Adobe indesigne CS Page Maker edition....and its Page maker Plug-In pack
    But I did  with little complication.
    ..... installed the Adobe indesigne CS
    .....it says you must install the Page maker Plug-In pack
    .....so i started the  plugin cd said this  operating system is not supported
    "work around below"
    so i did explore cd and went into the Adobe Page maker Plug-In pack Directory on the CD
    and i right  Click Setup
    Select properties
    now select second tab at tob COMPATIBILITY
    check run this program in compatibility mode for:
    then make sure drop down says  Windows XP SP2
    then hit ok
    then and i right  Click Setup And select run as adminstrator
    hit allow if it prompts you and go thru the normal setup  like you would with XP  had no issues here works great........
    Hope this helps : )
    ps doing same for most xp programs  makes them run like they are in XP

  • How can i fix my side volume buttons including the silent switch?

    I just noticed all the buttons on the left side of my iphone 4 wont work at all how can i fix this?

    Take it to the Apple store and pay for an out of warranty replacement.    

  • HT5622 iPad 3 and my sound has stopped from speakers, but can get from headphones.  It's not the side switch and the volume is max in all areas.  Anyone got any ideas, what problem is and how to fix it thanks

    Hi,
    My iPad has just stopped working with sound from the speakers, it works fine with the headphones in.  The soft mute button is not made and the volume is at max.
    Any ideas what problem is and how to sort.  Thanks

    System sounds can be muted from the software switch in the task bar as well as from the side switch depending on how you have it set up. This my boilerplate resonse for sound issues.
    1. If you have no sound at all, even in the Music App, try rebooting the iPad.
    Reboot the iPad by holding down on the sleep and home buttons at the same time for about 10-15 seconds until the Apple Logo appears - ignore the red slider if it appears on the screen - let go of the buttons. Let the iPad start up.
    2. If you lost sounds for keyboard clicks, games or other apps, email notifications and other notifications, system sounds may have been muted.
    System sounds can be muted and controlled two different ways. The screen lock rotation can be controlled in the same manner as well.
    Settings>General>Use Side Switch to: Mute System sounds. If this option is selected, the switch on the side of the iPad above the volume rocker will mute system sounds.
    If you choose Lock Screen Rotation, then the switch locks the screen. If the screen is locked, you will see a lock icon in the upper right corner next to the battery indicator gauge.
    If you have the side switch set to lock screen rotation then the system sound control is in the task bar. Double tap the home button and in the task bar at the bottom, swipe all the way to the right. The speaker icon is all the way to the left. Tap on it and system sounds will return.
    If you have the side switch set to mute system sounds, then the screen lock rotation can be accessed via the task bar in the same manner as described above.
    This support article from Apple explains how the side switch works.
    http://support.apple.com/kb/HT4085
    3. If you still have no sound at all - except when using headphones ....try cleaning the dock connector opening of the iPad with a soft brush and just a little bit of rubbing alcohol.

  • Was in iphoto and computer froze with spinning wheel.  I have tried to force quit and it won't even do that.  I can not even turn it off by pressing the power switch.  what should I do - unplug it?

    I was in iphoto and tried to edit a photo and computer froze.  I then tried to do a force quit but it still didn't do anything.  I tried this a few times.  After 5 hours I tried to shut off computer and it didn't do anything.  Should I just unplug it?

    yes. the solution of last resort. now, as to why your computer froze when you were trying to edit a photo in iPhoto, I can't help you much. Maybe a lack of ram, maybe something else running in the background,  hogging system resources. try running disc utility and repairing preferences. Also check activity monitor while your machine is running so you can find out if there is a hog or not. if force quit doesn't work, there's not much else you can do. I'll leave it to someone else to suggest other possible solutions
    JB

  • Can I use DHCP snooping and IOS DHCP server on the same switch stack

    Hello,
    I am shortly going to be deploying a Cisco CallManager solution for a customer whose network comprises stacks of Catalyst 3850 switches.
    There is no separate core/server farm switch so the CallManager servers, voice gateways and IP phones will all plug into the same stack and be in the same VLAN (not my choice!).
    For security we want to enable DHCP snooping and were planning on using the IOS DHCP server on the Catalyst switch stack.
    Will this work? - when I enable DHCP snooping in networks with separate access layer switches I set the uplinks to the core as trusted links.
    I am not sure whether DHCP snooping will work in this case. Do I need to set the VLAN interface on the switch as trusted, is this even possible?
    Unfortunately I do not have access to a layer 3 switch to test this at the moment.
    Thanks

    Nope.  That's the issue.
    They'll sync on a third device acting as a hotspot, but the device sending a signal is not "on" the network it creates so the airport is all by itself on that network.  At least that is what it looks like to me.  Anyone have another take on it?  Seems pretty silly that an iPad can put out a wifi signal, an Airport Express can receive a wifi signal, and yet there is no simple way to get them to communicate under this particular condition.

  • How do I do this to use OVerdrive media on deviceThe Apple device must be formatted for use with Microsoft Windows.  The iTunes setting 'Manually manage music-' must be enabled for the device before you can complete the transfer.

    I cannot make these directions work
    I downloaded media on Overdrive MEdia on my PC
    I have the overdrive media ap on my I pod touch 4g
    this media is suppossed to be compatible w/I pd touch
    Notes on Transferring OverDrive MP3 Audiobooks…
    Most MP3 capable devices should play OverDrive MP3 Audiobooks.
    If you intend to transfer OverDrive MP3 Audiobooks to an Apple® device, note the following…
    iTunes® v9.0.2 (or newer) is required.
    The Apple device must be formatted for use with Microsoft® Windows®.
    The iTunes setting 'Manually manage music…' must be enabled for the device before you can complete the transfer. Adjust this setting in iTunes as follows…
    Connect the iPod® to your computer.
    If it does not launch automatically, open iTunes v9.0.2 (or newer).
    In iTunes, locate the device in the left vertical navigation panel (under heading 'DEVICES'), and click the device.
    The 'Summary' screen is displayed. 
    Place a checkmark next to 'Manually manage music…'.
    Click the 'Apply' button.
    The iTunes 'Summary' screen refreshes, and the changes are saved.
    If desired, close iTunes.
    Note that if an Apple device is connected to your computer, you can choose to simultaneously transfer a title to the iTunes Library and the Apple device. If you wish to only transfer a title to the iTunes Library, you must first disconnect the Apple device

    Recovering your iTunes library from your iPod or iOS device: Apple Support Communities
    Also you said " I want to add them to my iCloud, and also back to my computer.   " Note that unless  subscribe to iTunes match, only iTunes purchases are stored in iCloud.
    Also,
    You can redownload most iTunes purchases by:
      Downloading past purchases from the App Store, iBookstore, and iTunes Store

  • TS4020 I live in a house with multiple iCloud users.  When they try to turn on "Find my computer"  they get the message that they will have to disable my "find my computer" setting in order to enable theirs.  How can they all be enabled at the same time?

    I live in a house with multiple iCloud users.  When they try to turn on "Find my computer"  they get the message that they will have to disable my "find my computer" setting in order to enable theirs.  How can they all be enabled at the same time?

    Try this support document for information on how to contact Apple and account security. Apple ID: Contacting Apple for help with Apple ID account security

  • Siri can't find music unless I enable use cellular data for Music

    I have an iPhone 4S with the latest IOS.  I ask Siri to play music but "she" can't find it unless I "enable" Use Cellular Data for Music.
    As soon as I enabled this setting in the Settings -> Cellular section Siri could find and play the music.
    I certainly don't understand why this is happening.  Why isn't Siri able to just find what is local to my iPhone and play the music.
    Can someone enlighten me on why this would happen?

    Hi Chris,
    Songs are on the iPhone - there is no cloud symbol (I'm familiar with that as well). 
    I've updated my signature - I am running the latest OSX and IOS (thanks for reminding me).

  • How can I enable/disable the transmission of a can frame? (filter etc...)

    Hello,
    I use the CAN
    Transmit-periodic.vi in LV 8.5, I want to enable or disable the
    transmission of a frame without stop the loop of my VI, does it exist
    in the frame api a vi which could stop, or mask the transmission of a
    frame?
    It's important I don't want to stop my VI that
    send my frame just filter a frame that I don't want send on my CAN
    bus...(I would command it with a boolean for example).
    Thank you.
    Bye.

    Hi there
    I'm not familiar with NI-CAN, but take a look at
    \vi.lib\Nican\nican.llb\ncAction.vi
    Can be found in the CAN\Frame API\Advanced palette.
    Start Transitions the CAN object from stopped (idle) state to started (running) state. If the CAN object is already started, this operation has no effect.
    Stop Stops the CAN Object. For example, if the CAN Object is configured to transmit data frames periodically, this action stops the periodic transmissions. This action will also clear all entries from the read queue.
    Best regards
    chris
    CL(A)Dly bending G-Force with LabVIEW
    famous last words: "oh my god, it is full of stars!"

  • How can you enable back the Android native Menu button in AIR 2.7?

    I've noticed in AIR 2.7 for Android, that now the bottom icons in Android 3.0 Honeycomb are hidden (replaced by small dots) in AIR 2.7, whereas in AIR 2.6 they were always visible. That's cool. Since the bottom bar can never be hidden in Android 3, at least now those icons are less visible (unless you intentionally touch the bottom bar, then the icons show up for a few seconds).
    BUT I also noticed in AIR 2.7 compiled apps, the native "Menu" icon is not visible anymore, even after touching the bottom bar. In AIR 2.6 you could see and press that button (which can be captured from AIR so you can show a custom settings menu or whatever).
    So, quoting the subject --> How can you enable back the Android native Menu button in AIR 2.7?

    There is a work around and a reason for the menu issue.  Honeycomb doesn't natively support a menu softkey, it is only to support old apps comiled in phone API levels.  If you compile a Honeycomb app in 2.7 or 3.0, it is expected you manage the settings within the larger tablet UI framework.  See below link for more info and work around. 
    http://forums.adobe.com/message/3964792#3964792

  • I have ical on two computers. Can't get ical (vers. 4) with OS 10.6 to copy to older desk top with OS 10.4 with ical vers 2. Is there a way to do this?

    I have ical on two computers. Can't get ical (vers. 4) with OS 10.6 to copy to older desk top with OS 10.4 with ical vers 2. Is there a way to do this?

    No. iCal isn't just the program you open to see the calendars, there are other things going on beneath the surface, and it's hooked into the System. 10.4 doesn't have the facilities to run iCal intended for 10.6.

  • I have Reader ver 9.0. If I receive a file which is created in ver 8.00, how can I open it ver 9.0 ?

    I have Reader ver 9.0. If I receive a file which is created in ver 8.00, how can I open it ver 9.0 ?

    All Adobe Reader versions are backwards compatible, so you should be able to open Acrobat 8 and earlier documents with Reader 9.
    Do you have a specific problem with a document and Reader 9?  If so, please give more details.

  • Since updating to Firefox 3.6.15, I can no longer print coupons from SmartSource. The error message is that Java is not detected. The check box is longer showing in the Options/Content of this version of Firefox, so I can not enable it.

    # Question
    Since updating to Firefox 3.6.15, I can no longer print coupons from SmartSource. The error message is that Java is not detected. The check box is longer showing in the Options/Content of this version of Firefox, so I can not enable it.

    Same PC as I used to post the question. When I go to the "plug in check" page, it shows I am up to date and it is not disabled.
    Java(TM) Platform SE 6 U24
    Next Generation Java Plug-in 1.6.0_24 for Mozilla browsers 1.6.0.24

Maybe you are looking for