Can't connect to a customer when I'm connected to my ASA5510 VPN.
Hi.
I need to connect to a remote customer from home via the office's vpn.
When I am physically at the office, I can connect no problem to my customer's securised gateway using my Internet Explorer browser (https://...).
(NB - when I go to the site speedtest.net, it indicated that my source IP address is our office's Internet Supplier - Bell.ca 67.70.xxx.x - which is correct).
When I am home, I connect VPN (with Cisco VPN Client) to my offices' cisco asa5510 . I then open my Internet Explorer browser and enter my customer's https:// address, unfortunately I get the error message saying I am not authorised to connet to the site.
I go to the site speedtest.net, and my source IP address is my home's Internet supplier (Videotron.ca 24.200.162.27).
My customer will only allow me in if the source ip is from Bell.ca 67.70.xxx.x (office) not Videotron.ca 24.200.162.27 (home).
How can I resolve my problem? Created a seperate group policy, tried different Split Tunnel Policy, actually tried all I can think of !!
I was certain it had to do with the Split Tunnel Policy in the Group Policy but not sure anymore .
Any suggestions?
Thanks
Your VPN would have to DISALLOW split tunnel, making all your Internet traffic come from the office network when you are VPN-connected.
Similar Messages
-
Can't connect to work through VPN.
I have the following: Router: Linksys WRT54GS v.4 + latest firmware VPN Software: Cisco VPN Client 4.8.02.0010 Cable Internet provider: Comcast The VPN client works fine if I connect using a Sprint air card, so that part is working. I just can't connect through my home router. Any advice? I'm stumped. Thanks in advance, John Duke
access the router using http://192.168.1.1 . the default password is admin .. go to the "applications and gaming" tab and click on "port trigerring" subtab ... enter ports 1723,50,500,443-447,43-47,10000-10001 .
if this does not make any difference...try upgrading / reflashing the router's firmware and check whether it makes any difference .. -
Environment:
2 x ASA 5540s (at two different data centers) configured as a VPN Load Balancing Cluster
Both ASAs are at version 8.4(5)6
IPSec VPN Client version: 5.0.07.440 (64-bit)
Jabber for Windows v9.7.0 build 18474
Issue:
If I am an IPSec VPN user…
I can use Jabber to another IPSec VPN user that is connected to the same ASA appliance.
I can’t use Jabber to another IPSec VPN user that is connected to the different ASA appliance that I am connected to.
In the hub-and-spoke design, where the VPN ASA is a hub, and the VPN client is a spoke; if you have two hubs clustered together, how does one spoke communicate with another spoke on the other hub in the cluster? (How to allow hairpinning to the other ASA)Portu,
Thanks for your quick reply.
Unfortunately, I do not have access to the ASA logs nor would I be permitted to turn on the debug settings asked for above. I might be able to get the logs but it will take awhile and I suspect they wouldn't be helpful as this ASA supports thousands of clients, therefore, separating out my connection attempts from other clients would be difficult.
I can, though, do whatever you want on the Linux router. Looking over the firewall logs at the time of this problem, I don't see anything that looks suspicious such as dropped packets destined for the Windows client.
As I said in my original post, I'm not a networking expert - by any means - but I am willing to try anything to resolve this. (But I might need a bit of handholding if I need to set up a wireshark andor tcpdump.)
Thanks again. -
Can't Connect to Pix 501 VPN on Network
Hi All,
I have a software VPN client that connects just fine to the PIX 501 VPN, but I cannot ping or telnet to any services on the LAN. Below is my config and results of show cry ipsec sa. I would appreciate any suggestions to fix this.
It's been a while since I have done this. When I check the DHCP address received from the VPN, the default gateway is missing. IIRC, that is normal. What is strange is that when I ping, Windows does not show any sent packets.
Thanks,
--Drichards38
PIX Version 6.3(3)
interface ethernet0 auto
interface ethernet1 100full
nameif ethernet0 outside security0
nameif ethernet1 inside security100
enable password bgVy005CZTsaMOwR encrypted
passwd bgVy005CZTsaMOwR encrypted
hostname cisco
domain-name xxxxxx.biz
fixup protocol dns maximum-length 512
fixup protocol ftp 21
fixup protocol ftp 1024-2048
fixup protocol ftp 49152-65534
fixup protocol h323 h225 1720
fixup protocol h323 ras 1718-1719
fixup protocol http 80
fixup protocol rsh 514
fixup protocol rtsp 554
fixup protocol sip 5060
fixup protocol sip udp 5060
fixup protocol skinny 2000
fixup protocol smtp 25
fixup protocol sqlnet 1521
fixup protocol tftp 69
names
access-list acl-out permit tcp any interface outside eq www
access-list acl_out permit tcp any host aa.bb.cc.dd eq telnet
access-list acl_out permit tcp any host aa.bb.cc.dd eq 3389
access-list acl_out permit tcp any host aa.bb.cc.dd eq 60990
access-list acl_out permit tcp any host aa.bb.cc.dd eq www
access-list acl_out permit tcp any host aa.bb.cc.dd eq www
access-list acl_out permit tcp any host aa.bb.cc.dd eq echo
access-list acl_out permit tcp any host aa.bb.cc.dd eq ftp
access-list acl_out permit tcp any host aa.bb.cc.dd eq https
access-list acl_out permit tcp any interface inside eq www
access-list acl_out permit tcp any interface inside eq ftp
access-list acl_out permit tcp any interface inside eq 3389
access-list acl_out permit tcp any interface inside eq https
access-list acl_out permit tcp any host aa.bb.cc.dd eq www
access-list acl_out permit tcp any host aa.bb.cc.dd eq www
access-list acl_out permit tcp any host aa.bb.cc.dd eq https
access-list acl_out permit tcp any host aa.bb.cc.dd eq https
access-list acl_out permit tcp any host aa.bb.cc.dd eq 3389
access-list acl_out permit tcp any host aa.bb.cc.dd eq 3389
access-list acl_out permit tcp any host aa.bb.cc.dd eq www
access-list acl_out permit tcp any host aa.bb.cc.dd eq https
access-list acl_out permit tcp any host aa.bb.cc.dd eq 3389
access-list acl_out permit tcp any host aa.bb.cc.dd eq ftp
access-list acl_out permit tcp any host aa.bb.cc.dd eq www
access-list acl_out permit tcp any host aa.bb.cc.dd eq https
access-list acl_out permit tcp any host aa.bb.cc.dd eq 3389
access-list acl_out permit tcp any host aa.bb.cc.dd eq 902
access-list acl_out permit tcp any host aa.bb.cc.dd eq ftp
access-list acl_out permit tcp any host aa.bb.cc.dd eq www
access-list acl_out permit tcp any host aa.bb.cc.dd eq ftp
access-list acl_out permit tcp any host aa.bb.cc.dd eq https
access-list acl_out permit tcp any host aa.bb.cc.dd eq 3389
access-list acl_out permit tcp any host aa.bb.cc.dd eq www
access-list acl_out permit tcp any host aa.bb.cc.dd eq ftp
access-list acl_out permit tcp any host aa.bb.cc.dd eq https
access-list acl_out permit tcp any host aa.bb.cc.dd eq 3389
access-list acl_out permit tcp any host aa.bb.cc.dd eq www
access-list acl_out permit tcp any host aa.bb.cc.dd eq https
access-list acl_out permit tcp any host aa.bb.cc.dd eq ftp
access-list acl_out permit tcp any host aa.bb.cc.dd eq 3389
access-list outside_cryptomap_dyn_20 permit ip any 10.0.0.0 255.0.0.0
access-list split_tunnel_acl permit ip 10.0.0.0 255.0.0.0 any
pager lines 24
mtu outside 1500
mtu inside 1500
ip address outside aa.bb.cc.dd 255.255.255.240
ip address inside 192.168.93.1 255.255.255.0
ip audit info action alarm
ip audit attack action alarm
ip local pool low_vpn_pool 10.0.1.205-10.0.1.210
pdm location 172.16.0.0 255.255.0.0 inside
pdm logging informational 100
pdm history enable
arp timeout 14400
global (outside) 1 interface
nat (inside) 1 192.168.93.0 255.255.255.0 0 0
nat (inside) 1 0.0.0.0 0.0.0.0 0 0
static (inside,outside) aa.bb.cc.dd 192.168.93.67 netmask 255.255.255.255 0 0
static (inside,outside) aa.bb.cc.dd 192.168.93.68 netmask 255.255.255.255 0 0
static (inside,outside) aa.bb.cc.dd 192.168.93.69 netmask 255.255.255.255 0 0
static (inside,outside) aa.bb.cc.dd 192.168.93.70 netmask 255.255.255.255 0 0
static (inside,outside) aa.bb.cc.dd 192.168.93.71 netmask 255.255.255.255 0 0
static (inside,outside) aa.bb.cc.dd 192.168.93.72 netmask 255.255.255.255 0 0
static (inside,outside) aa.bb.cc.dd 192.168.93.73 netmask 255.255.255.255 0 0
static (inside,outside) aa.bb.cc.dd 192.168.93.74 netmask 255.255.255.255 0 0
static (inside,outside) aa.bb.cc.dd 192.168.93.75 netmask 255.255.255.255 0 0
static (inside,outside) aa.bb.cc.dd 192.168.93.76 netmask 255.255.255.255 0 0
static (inside,outside) aa.bb.cc.dd 192.168.93.77 netmask 255.255.255.255 0 0
static (inside,outside) aa.bb.cc.dd 192.168.93.78 netmask 255.255.255.255 0 0
access-group acl_out in interface outside
rip inside default version 1
route outside 0.0.0.0 0.0.0.0 aa.bb.cc.dd 1
timeout xlate 0:05:00
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 rpc 0:10:00 h225 1:00:00
timeout h323 0:05:00 mgcp 0:05:00 sip 0:30:00 sip_media 0:02:00
timeout uauth 0:05:00 absolute
aaa-server TACACS+ protocol tacacs+
aaa-server RADIUS protocol radius
aaa-server LOCAL protocol local
aaa authorization command LOCAL
http server enable
no snmp-server location
no snmp-server contact
snmp-server community public
no snmp-server enable traps
floodguard enable
sysopt connection permit-ipsec
crypto ipsec transform-set ESP-3DES-SHA esp-3des esp-sha-hmac
crypto ipsec transform-set ESP-3DES-MD5 esp-3des esp-md5-hmac
crypto dynamic-map outside_dyn_map 20 match address outside_cryptomap_dyn_20
crypto dynamic-map outside_dyn_map 20 set transform-set ESP-3DES-MD5
crypto map outside_map 65535 ipsec-isakmp dynamic outside_dyn_map
crypto map outside_map client authentication LOCAL
crypto map outside_map interface outside
isakmp enable outside
isakmp nat-traversal 20
isakmp policy 20 authentication pre-share
isakmp policy 20 encryption 3des
isakmp policy 20 hash md5
isakmp policy 20 group 2
isakmp policy 20 lifetime 86400
vpngroup MY_VPN address-pool low_vpn_pool
vpngroup MY_VPN dns-server 4.2.2.1
vpngroup MY_VPN default-domain xxxxx.biz
vpngroup MY_VPN split-tunnel split_tunnel_acl
vpngroup MY_VPN idle-time 1800
vpngroup MY_VPN password ********
telnet 0.0.0.0 255.255.255.255 outside
telnet 192.168.93.0 255.255.255.0 inside
telnet timeout 5
ssh 0.0.0.0 0.0.0.0 outside
ssh timeout 60
console timeout 0
dhcpd address 192.168.93.230-192.168.93.240 inside
dhcpd dns ff.gg.hh.ii ff.gg.hh.ii
dhcpd lease 65536
dhcpd ping_timeout 750
dhcpd domain xxxxxx.biz
dhcpd auto_config outside
dhcpd enable inside
username xxxx password xxxxxxx encrypted privilege 15
cisco(config)# show cry ipsec sa
interface: outside
Crypto map tag: outside_map, local addr. aa.bb.cc.dd
local ident (addr/mask/prot/port): (0.0.0.0/0.0.0.0/0/0)
remote ident (addr/mask/prot/port): (10.0.1.205/255.255.255.255/0/0)
current_peer: jj.kk.ll.mm:1265
dynamic allocated peer ip: 10.0.1.205
PERMIT, flags={transport_parent,}
#pkts encaps: 0, #pkts encrypt: 0, #pkts digest 0
#pkts decaps: 38, #pkts decrypt: 38, #pkts verify 38
#pkts compressed: 0, #pkts decompressed: 0
#pkts not compressed: 0, #pkts compr. failed: 0, #pkts decompress failed: 0
#send errors 0, #recv errors 0
local crypto endpt.: aa.bb.cc.dd, remote crypto endpt.: 97.93.95.133
path mtu 1500, ipsec overhead 64, media mtu 1500
current outbound spi: 3a898e67
inbound esp sas:
spi: 0xeeb64931(4004923697)
transform: esp-3des esp-md5-hmac ,
in use settings ={Tunnel UDP-Encaps, }
slot: 0, conn id: 1, crypto map: outside_map
sa timing: remaining key lifetime (k/sec): (4607993/28610)
IV size: 8 bytes
replay detection support: Y
inbound ah sas:
inbound pcp sas:
outbound esp sas:
spi: 0x3a898e67(982093415)
transform: esp-3des esp-md5-hmac ,
in use settings ={Tunnel UDP-Encaps, }
slot: 0, conn id: 2, crypto map: outside_map
sa timing: remaining key lifetime (k/sec): (4608000/28574)
IV size: 8 bytes
replay detection support: Y
outbound ah sas:
outbound pcp sas:I just set the logging to high on all areas of the Cisco VPN client. Below is the resulting log. Everything looks ok from here:
Cisco Systems VPN Client Version 5.0.03.0530
Copyright (C) 1998-2007 Cisco Systems, Inc. All Rights Reserved.
Client Type(s): Windows, WinNT
Running on: 5.1.2600 Service Pack 3
29 09:57:02.887 09/03/12 Sev=Info/4 CM/0x63100002
Begin connection process
30 09:57:02.897 09/03/12 Sev=Info/4 CM/0x63100004
Establish secure connection
31 09:57:02.897 09/03/12 Sev=Info/4 CM/0x63100024
Attempt connection with server "a.b.c.d"
32 09:57:02.907 09/03/12 Sev=Info/6 IKE/0x6300003B
Attempting to establish a connection with a.b.c.d.
33 09:57:02.917 09/03/12 Sev=Info/4 IKE/0x63000013
SENDING >>> ISAKMP OAK AG (SA, KE, NON, ID, VID(Xauth), VID(dpd), VID(Frag), VID(Nat-T), VID(Unity)) to a.b.c.d
34 09:57:03.228 09/03/12 Sev=Info/4 IPSEC/0x63700008
IPSec driver successfully started
35 09:57:03.228 09/03/12 Sev=Info/4 IPSEC/0x63700014
Deleted all keys
36 09:57:03.228 09/03/12 Sev=Info/6 IPSEC/0x6370002C
Sent 47 packets, 0 were fragmented.
37 09:57:03.979 09/03/12 Sev=Info/5 IKE/0x6300002F
Received ISAKMP packet: peer = a.b.c.d
38 09:57:03.979 09/03/12 Sev=Info/4 IKE/0x63000014
RECEIVING <<< ISAKMP OAK AG (SA, VID(Xauth), VID(dpd), VID(Unity), VID(?), KE, ID, NON, VID(?), VID(Nat-T), NAT-D, NAT-D, HASH) from a.b.c.d
39 09:57:04.039 09/03/12 Sev=Info/6 GUI/0x63B00012
Authentication request attributes is 6h.
40 09:57:03.979 09/03/12 Sev=Info/5 IKE/0x63000001
Peer supports XAUTH
41 09:57:03.979 09/03/12 Sev=Info/5 IKE/0x63000001
Peer supports DPD
42 09:57:03.979 09/03/12 Sev=Info/5 IKE/0x63000001
Peer is a Cisco-Unity compliant peer
43 09:57:03.979 09/03/12 Sev=Info/5 IKE/0x63000082
Received IOS Vendor ID with unknown capabilities flag 0x000000A5
44 09:57:03.979 09/03/12 Sev=Info/5 IKE/0x63000001
Peer supports NAT-T
45 09:57:03.999 09/03/12 Sev=Info/6 IKE/0x63000001
IOS Vendor ID Contruction successful
46 09:57:03.999 09/03/12 Sev=Info/4 IKE/0x63000013
SENDING >>> ISAKMP OAK AG *(HASH, NOTIFY:STATUS_INITIAL_CONTACT, NAT-D, NAT-D, VID(?), VID(Unity)) to a.b.c.d
47 09:57:03.999 09/03/12 Sev=Info/6 IKE/0x63000055
Sent a keepalive on the IPSec SA
48 09:57:03.999 09/03/12 Sev=Info/4 IKE/0x63000083
IKE Port in use - Local Port = 0x0421, Remote Port = 0x1194
49 09:57:03.999 09/03/12 Sev=Info/5 IKE/0x63000072
Automatic NAT Detection Status:
Remote end is NOT behind a NAT device
This end IS behind a NAT device
50 09:57:03.999 09/03/12 Sev=Info/4 CM/0x6310000E
Established Phase 1 SA. 1 Crypto Active IKE SA, 0 User Authenticated IKE SA in the system
51 09:57:04.029 09/03/12 Sev=Info/5 IKE/0x6300002F
Received ISAKMP packet: peer = a.b.c.d
52 09:57:04.029 09/03/12 Sev=Info/4 IKE/0x63000014
RECEIVING <<< ISAKMP OAK INFO *(HASH, NOTIFY:STATUS_INITIAL_CONTACT) from a.b.c.d
53 09:57:04.029 09/03/12 Sev=Warning/2 IKE/0xA3000067
Received Unexpected InitialContact Notify (PLMgrNotify:886)
54 09:57:04.039 09/03/12 Sev=Info/5 IKE/0x6300002F
Received ISAKMP packet: peer = a.b.c.d
55 09:57:04.039 09/03/12 Sev=Info/4 IKE/0x63000014
RECEIVING <<< ISAKMP OAK INFO *(HASH, NOTIFY:STATUS_RESP_LIFETIME) from a.b.c.d
56 09:57:04.039 09/03/12 Sev=Info/5 IKE/0x63000045
RESPONDER-LIFETIME notify has value of 86400 seconds
57 09:57:04.039 09/03/12 Sev=Info/5 IKE/0x63000047
This SA has already been alive for 2 seconds, setting expiry to 86398 seconds from now
58 09:57:04.039 09/03/12 Sev=Info/5 IKE/0x6300002F
Received ISAKMP packet: peer = a.b.c.d
59 09:57:04.039 09/03/12 Sev=Info/4 IKE/0x63000014
RECEIVING <<< ISAKMP OAK TRANS *(HASH, ATTR) from a.b.c.d
60 09:57:04.039 09/03/12 Sev=Info/4 CM/0x63100015
Launch xAuth application
61 09:57:09.327 09/03/12 Sev=Info/4 CM/0x63100017
xAuth application returned
62 09:57:09.327 09/03/12 Sev=Info/4 IKE/0x63000013
SENDING >>> ISAKMP OAK TRANS *(HASH, ATTR) to a.b.c.d
63 09:57:09.367 09/03/12 Sev=Info/5 IKE/0x6300002F
Received ISAKMP packet: peer = a.b.c.d
64 09:57:09.367 09/03/12 Sev=Info/4 IKE/0x63000014
RECEIVING <<< ISAKMP OAK TRANS *(HASH, ATTR) from a.b.c.d
65 09:57:09.367 09/03/12 Sev=Info/4 IKE/0x63000013
SENDING >>> ISAKMP OAK TRANS *(HASH, ATTR) to a.b.c.d
66 09:57:09.367 09/03/12 Sev=Info/4 CM/0x6310000E
Established Phase 1 SA. 1 Crypto Active IKE SA, 1 User Authenticated IKE SA in the system
67 09:57:09.387 09/03/12 Sev=Info/5 IKE/0x6300005E
Client sending a firewall request to concentrator
68 09:57:09.387 09/03/12 Sev=Info/5 IKE/0x6300005D
Firewall Policy: Product=Cisco Systems Integrated Client Firewall, Capability= (Centralized Protection Policy).
69 09:57:09.387 09/03/12 Sev=Info/4 IKE/0x63000013
SENDING >>> ISAKMP OAK TRANS *(HASH, ATTR) to a.b.c.d
70 09:57:09.427 09/03/12 Sev=Info/5 IKE/0x6300002F
Received ISAKMP packet: peer = a.b.c.d
71 09:57:09.427 09/03/12 Sev=Info/4 IKE/0x63000014
RECEIVING <<< ISAKMP OAK TRANS *(HASH, ATTR) from a.b.c.d
72 09:57:09.427 09/03/12 Sev=Info/5 IKE/0x63000010
MODE_CFG_REPLY: Attribute = INTERNAL_IPV4_ADDRESS: , value = 10.0.1.205
73 09:57:09.427 09/03/12 Sev=Info/5 IKE/0x63000010
MODE_CFG_REPLY: Attribute = INTERNAL_IPV4_DNS(1): , value = 4.2.2.1
74 09:57:09.427 09/03/12 Sev=Info/5 IKE/0x6300000E
MODE_CFG_REPLY: Attribute = MODECFG_UNITY_DEFDOMAIN: , value = xxxx.biz
75 09:57:09.427 09/03/12 Sev=Info/5 IKE/0x6300000D
MODE_CFG_REPLY: Attribute = MODECFG_UNITY_SPLIT_INCLUDE (# of split_nets), value = 0x00000001
76 09:57:09.427 09/03/12 Sev=Info/5 IKE/0x6300000F
SPLIT_NET #1
subnet = 10.0.0.0
mask = 255.0.0.0
protocol = 0
src port = 0
dest port=0
77 09:57:09.427 09/03/12 Sev=Info/5 IKE/0x6300000D
MODE_CFG_REPLY: Attribute = MODECFG_UNITY_PFS: , value = 0x00000000
78 09:57:09.427 09/03/12 Sev=Info/5 IKE/0x6300000D
MODE_CFG_REPLY: Attribute = Received and using NAT-T port number , value = 0x00001194
79 09:57:09.427 09/03/12 Sev=Info/4 CM/0x63100019
Mode Config data received
80 09:57:09.427 09/03/12 Sev=Info/4 IKE/0x63000056
Received a key request from Driver: Local IP = 10.0.1.205, GW IP = a.b.c.d, Remote IP = 0.0.0.0
81 09:57:09.437 09/03/12 Sev=Info/4 IKE/0x63000013
SENDING >>> ISAKMP OAK QM *(HASH, SA, NON, ID, ID) to a.b.c.d
82 09:57:09.477 09/03/12 Sev=Info/5 IKE/0x6300002F
Received ISAKMP packet: peer = a.b.c.d
83 09:57:09.477 09/03/12 Sev=Info/4 IKE/0x63000014
RECEIVING <<< ISAKMP OAK QM *(HASH, SA, NON, ID, ID, NOTIFY:STATUS_RESP_LIFETIME) from a.b.c.d
84 09:57:09.477 09/03/12 Sev=Info/5 IKE/0x63000045
RESPONDER-LIFETIME notify has value of 28800 seconds
85 09:57:09.477 09/03/12 Sev=Info/5 IKE/0x63000046
RESPONDER-LIFETIME notify has value of 4608000 kb
86 09:57:09.477 09/03/12 Sev=Info/4 IKE/0x63000013
SENDING >>> ISAKMP OAK QM *(HASH) to a.b.c.d
87 09:57:09.477 09/03/12 Sev=Info/5 IKE/0x63000059
Loading IPsec SA (MsgID=D70550E6 OUTBOUND SPI = 0xB335C6DA INBOUND SPI = 0xE99E1A59)
88 09:57:09.477 09/03/12 Sev=Info/5 IKE/0x63000025
Loaded OUTBOUND ESP SPI: 0xB335C6DA
89 09:57:09.477 09/03/12 Sev=Info/5 IKE/0x63000026
Loaded INBOUND ESP SPI: 0xE99E1A59
90 09:57:09.527 09/03/12 Sev=Info/5 CVPND/0x63400013
Destination Netmask Gateway Interface Metric
0.0.0.0 0.0.0.0 172.16.0.1 172.16.0.11 25
127.0.0.0 255.0.0.0 127.0.0.1 127.0.0.1 1
172.16.0.0 255.255.0.0 172.16.0.11 172.16.0.11 25
172.16.0.11 255.255.255.255 127.0.0.1 127.0.0.1 25
172.16.255.255 255.255.255.255 172.16.0.11 172.16.0.11 25
224.0.0.0 240.0.0.0 172.16.0.11 172.16.0.11 25
255.255.255.255 255.255.255.255 172.16.0.11 0.0.0.0 1
255.255.255.255 255.255.255.255 172.16.0.11 172.16.0.11 1
91 09:57:10.448 09/03/12 Sev=Info/4 CM/0x63100034
The Virtual Adapter was enabled:
IP=10.0.1.205/255.0.0.0
DNS=4.2.2.1,0.0.0.0
WINS=0.0.0.0,0.0.0.0
Domain=xxxx.biz
Split DNS Names=
92 09:57:10.458 09/03/12 Sev=Info/5 CVPND/0x63400013
Destination Netmask Gateway Interface Metric
0.0.0.0 0.0.0.0 172.16.0.1 172.16.0.11 25
10.0.0.0 255.0.0.0 10.0.1.205 10.0.1.205 25
10.0.1.205 255.255.255.255 127.0.0.1 127.0.0.1 25
10.255.255.255 255.255.255.255 10.0.1.205 10.0.1.205 25
127.0.0.0 255.0.0.0 127.0.0.1 127.0.0.1 1
172.16.0.0 255.255.0.0 172.16.0.11 172.16.0.11 25
172.16.0.11 255.255.255.255 127.0.0.1 127.0.0.1 25
172.16.255.255 255.255.255.255 172.16.0.11 172.16.0.11 25
224.0.0.0 240.0.0.0 10.0.1.205 10.0.1.205 25
224.0.0.0 240.0.0.0 172.16.0.11 172.16.0.11 25
255.255.255.255 255.255.255.255 10.0.1.205 0.0.0.0 1
255.255.255.255 255.255.255.255 10.0.1.205 10.0.1.205 1
255.255.255.255 255.255.255.255 172.16.0.11 172.16.0.11 1
93 09:57:10.458 09/03/12 Sev=Info/4 CM/0x63100038
Successfully saved route changes to file.
94 09:57:10.458 09/03/12 Sev=Info/5 CVPND/0x63400013
Destination Netmask Gateway Interface Metric
0.0.0.0 0.0.0.0 172.16.0.1 172.16.0.11 25
10.0.0.0 255.0.0.0 10.0.1.205 10.0.1.205 1
10.0.1.205 255.255.255.255 127.0.0.1 127.0.0.1 25
10.255.255.255 255.255.255.255 10.0.1.205 10.0.1.205 25
a.b.c.d 255.255.255.255 172.16.0.1 172.16.0.11 1
127.0.0.0 255.0.0.0 127.0.0.1 127.0.0.1 1
172.16.0.0 255.255.0.0 172.16.0.11 172.16.0.11 25
172.16.0.1 255.255.255.255 172.16.0.11 172.16.0.11 1
172.16.0.11 255.255.255.255 127.0.0.1 127.0.0.1 25
172.16.255.255 255.255.255.255 172.16.0.11 172.16.0.11 25
224.0.0.0 240.0.0.0 10.0.1.205 10.0.1.205 25
224.0.0.0 240.0.0.0 172.16.0.11 172.16.0.11 25
255.255.255.255 255.255.255.255 10.0.1.205 0.0.0.0 1
255.255.255.255 255.255.255.255 10.0.1.205 10.0.1.205 1
255.255.255.255 255.255.255.255 172.16.0.11 172.16.0.11 1
95 09:57:10.458 09/03/12 Sev=Info/6 CM/0x63100036
The routing table was updated for the Virtual Adapter
96 09:57:10.508 09/03/12 Sev=Info/4 CM/0x6310001A
One secure connection established
97 09:57:10.618 09/03/12 Sev=Info/4 CM/0x6310003B
Address watch added for 172.16.0.11. Current hostname: toughone, Current address(es): 10.0.1.205, 172.16.0.11.
98 09:57:10.638 09/03/12 Sev=Info/4 CM/0x6310003B
Address watch added for 10.0.1.205. Current hostname: toughone, Current address(es): 10.0.1.205, 172.16.0.11.
99 09:57:10.638 09/03/12 Sev=Info/4 IPSEC/0x63700014
Deleted all keys
100 09:57:10.638 09/03/12 Sev=Info/4 IPSEC/0x63700010
Created a new key structure
101 09:57:10.638 09/03/12 Sev=Info/4 IPSEC/0x6370000F
Added key with SPI=0xdac635b3 into key list
102 09:57:10.638 09/03/12 Sev=Info/4 IPSEC/0x63700010
Created a new key structure
103 09:57:10.638 09/03/12 Sev=Info/4 IPSEC/0x6370000F
Added key with SPI=0x591a9ee9 into key list
104 09:57:10.638 09/03/12 Sev=Info/4 IPSEC/0x6370002F
Assigned VA private interface addr 10.0.1.205
105 09:57:10.638 09/03/12 Sev=Info/4 IPSEC/0x63700037
Configure public interface: 172.16.0.11. SG: a.b.c.d
106 09:57:10.638 09/03/12 Sev=Info/6 CM/0x63100046
Set tunnel established flag in registry to 1.
107 09:57:19.741 09/03/12 Sev=Info/4 IKE/0x63000013
SENDING >>> ISAKMP OAK INFO *(HASH, NOTIFY:DPD_REQUEST) to a.b.c.d
108 09:57:19.741 09/03/12 Sev=Info/6 IKE/0x6300003D
Sending DPD request to a.b.c.d, our seq# = 3951445672
109 09:57:19.772 09/03/12 Sev=Info/5 IKE/0x6300002F
Received ISAKMP packet: peer = a.b.c.d
110 09:57:19.772 09/03/12 Sev=Info/4 IKE/0x63000014
RECEIVING <<< ISAKMP OAK INFO *(HASH, NOTIFY:DPD_ACK) from a.b.c.d
111 09:57:19.772 09/03/12 Sev=Info/5 IKE/0x63000040
Received DPD ACK from a.b.c.d, seq# received = 3951445672, seq# expected = 3951445672
112 09:57:30.257 09/03/12 Sev=Info/4 IKE/0x63000013
SENDING >>> ISAKMP OAK INFO *(HASH, NOTIFY:DPD_REQUEST) to a.b.c.d
113 09:57:30.257 09/03/12 Sev=Info/6 IKE/0x6300003D
Sending DPD request to a.b.c.d, our seq# = 3951445673
114 09:57:30.297 09/03/12 Sev=Info/5 IKE/0x6300002F
Received ISAKMP packet: peer = a.b.c.d
115 09:57:30.297 09/03/12 Sev=Info/4 IKE/0x63000014
RECEIVING <<< ISAKMP OAK INFO *(HASH, NOTIFY:DPD_ACK) from a.b.c.d
116 09:57:30.297 09/03/12 Sev=Info/5 IKE/0x63000040
Received DPD ACK from a.b.c.d, seq# received = 3951445673, seq# expected = 3951445673
117 09:57:40.772 09/03/12 Sev=Info/4 IKE/0x63000013
SENDING >>> ISAKMP OAK INFO *(HASH, NOTIFY:DPD_REQUEST) to a.b.c.d
118 09:57:40.772 09/03/12 Sev=Info/6 IKE/0x6300003D
Sending DPD request to a.b.c.d, our seq# = 3951445674
119 09:57:40.802 09/03/12 Sev=Info/5 IKE/0x6300002F
Received ISAKMP packet: peer = a.b.c.d
120 09:57:40.802 09/03/12 Sev=Info/4 IKE/0x63000014
RECEIVING <<< ISAKMP OAK INFO *(HASH, NOTIFY:DPD_ACK) from a.b.c.d
121 09:57:40.802 09/03/12 Sev=Info/5 IKE/0x63000040
Received DPD ACK from a.b.c.d, seq# received = 3951445674, seq# expected = 3951445674
122 09:57:54.291 09/03/12 Sev=Info/6 IKE/0x63000055
Sent a keepalive on the IPSec SA
123 09:58:04.306 09/03/12 Sev=Info/6 IKE/0x63000055
Sent a keepalive on the IPSec SA
124 09:58:14.320 09/03/12 Sev=Info/6 IKE/0x63000055
Sent a keepalive on the IPSec SA
125 09:58:24.334 09/03/12 Sev=Info/6 IKE/0x63000055
Sent a keepalive on the IPSec SA
126 09:58:34.349 09/03/12 Sev=Info/6 IKE/0x63000055
Sent a keepalive on the IPSec SA
127 09:58:41.359 09/03/12 Sev=Info/4 IKE/0x63000013
SENDING >>> ISAKMP OAK INFO *(HASH, NOTIFY:DPD_REQUEST) to a.b.c.d
128 09:58:41.359 09/03/12 Sev=Info/6 IKE/0x6300003D
Sending DPD request to a.b.c.d, our seq# = 3951445675
129 09:58:41.389 09/03/12 Sev=Info/5 IKE/0x6300002F
Received ISAKMP packet: peer = a.b.c.d
130 09:58:41.389 09/03/12 Sev=Info/4 IKE/0x63000014
RECEIVING <<< ISAKMP OAK INFO *(HASH, NOTIFY:DPD_ACK) from a.b.c.d
131 09:58:41.389 09/03/12 Sev=Info/5 IKE/0x63000040
Received DPD ACK from a.b.c.d, seq# received = 3951445675, seq# expected = 3951445675
132 09:58:54.378 09/03/12 Sev=Info/6 IKE/0x63000055
Sent a keepalive on the IPSec SA
133 09:59:04.392 09/03/12 Sev=Info/6 IKE/0x63000055
Sent a keepalive on the IPSec SA
134 09:59:14.406 09/03/12 Sev=Info/6 IKE/0x63000055
Sent a keepalive on the IPSec SA
135 09:59:24.421 09/03/12 Sev=Info/6 IKE/0x63000055
Sent a keepalive on the IPSec SA
136 09:59:34.435 09/03/12 Sev=Info/6 IKE/0x63000055
Sent a keepalive on the IPSec SA
137 09:59:41.946 09/03/12 Sev=Info/4 IKE/0x63000013
SENDING >>> ISAKMP OAK INFO *(HASH, NOTIFY:DPD_REQUEST) to a.b.c.d
138 09:59:41.946 09/03/12 Sev=Info/6 IKE/0x6300003D
Sending DPD request to a.b.c.d, our seq# = 3951445676
139 09:59:41.976 09/03/12 Sev=Info/5 IKE/0x6300002F
Received ISAKMP packet: peer = a.b.c.d
140 09:59:41.976 09/03/12 Sev=Info/4 IKE/0x63000014
RECEIVING <<< ISAKMP OAK INFO *(HASH, NOTIFY:DPD_ACK) from a.b.c.d
141 09:59:41.976 09/03/12 Sev=Info/5 IKE/0x63000040
Received DPD ACK from a.b.c.d, seq# received = 3951445676, seq# expected = 3951445676
142 09:59:54.464 09/03/12 Sev=Info/6 IKE/0x63000055
Sent a keepalive on the IPSec SA -
Whenever I buy something in game, it says that " can not connect to itunes store". Why???? I fill all my payment information in app Store, bt I couldnt buy any thing. Why???
Additonally, at this point I really want to talk to someone who cares about how a customer like I might feel in such a situation and when I call corporate would like to talk to someone who is interested in hearing my input as it really sucks to think I really don't feel like going to the store anymore and would rather just buy stuff on amazon or newegg these days instead;/ When I know how much i used to enjoy going into the store and getting friendly with kind staff who worked with me to get the best deal on the items I got--perhaps this was because it was at a more desperate time when Best Buys fate as a company was more precarious prior to price matching taking origin. Also, on an aside, would like to add that obviously there is always the one or two people who go out of their way to make sure you have an excellent expeirenece so I am not trying to make any sweeping generalizations here. In fact, I find the forum contributors to be among the most kind and helpful, but that might be because they don't have to deal with the now seemingly dreaded "pricematch" epidemic;D
-
Since software update, can't see contents of iPod when connected to iTunes
About 2 days ago, when I connected my iPod to my pc (iTunes), it said there were some software updates for my iPod so I downloaded them and the iPod rebooted itself. Once it came back up, my iPod showed up in iTunes under "devices" on the left hand sidebar. I got the registration page - I usually click register later, but nothing happened this time. It didn't bring me into my iPod. So I tried to Register. I could get so far, then it asked if I wanted some free movie or something, I said NO THANKS, CONTINUE, but nothing happened. I wasn't registered AND I couldn't access my iPod. I can see my iPod under My Computer. I can see "sandra's iPod" uder devices in iTunes. BUT, I can't get to the content when connected to iTunes. All of my stuff is there on the iPod. I can play my iPod when it's not connected to iTunes - but I can't see the content, manipulate playlists, delete songs, etc. when connected to iTunes. I am almost positive this is a result of the latest software updates to the iPod. I have not updated iTunes - I didn't want to and compound the problem. I'm not a techy person - so please be gentle! Thank you. Sandra
Resolved at home.
-
when bluetooth headset is connected to iphone,I can't hear iphone ringing aloud when I have a call or a text. Do i really have to wear the bluetooth headset all the time in my ear to know when I have a call or a message? Why it doesnt ring through iphone but it rings through the bluetooth headsets?
In other phones, you can hear the phone ringing and if it was connected to bluetooth, you could pick up the call from the bluetooth headset.
Here with iphone, if its connected to bluetooth headset, it only rings through the headset, which means that if you dont have the headset in the ear all the time, you cannot know that you have an incoming call or message.
Any ideas - solutions - comments please?I'm having the same problem. I had a plantronics 975 (which I lost, sadly). When connected, the ringer would always be routed through the bluetooth and the iPhone's external speaker. When in silent mode, the iPhone would only vibrate, but I could still hear the ringer in the bluetooth.
I just bought a new Plantronics Voyager+. Now when it's connected, all sounds are routed to the earpiece - including the taps, etc. The iPhone's speaker doesn't ring at all, unless the bluetooth is disconnected or powered off. I'd really like to be able to hear both, like I was before. This is an iPhone 3G running iOS 4 (latest version, not sure what it is exactly). Haven't updated software/firmware in between bluetooths, just changed the earpiece. -
I want to use an old 3 GS iPhone that is no longer in service as a phone now as just an iPod to play music. When I connect the phone to the computer with iTunes running, iTunes says it can't connect to the device because it didn't get a valid response from the device. How can I get the system to recognize the phone, and let me rename it as my iPod, instead of my phone?
As an aside, the current installed operating system on this old iPhone is 4.2.1, but that wasn't one of the selectable options in the operating system list dropdown below. Don't know if that makes any difference.Hi maddogdne,
Welcome to the Support Communities!
The article below may be able to help you with this.
Click on the link to see more details and screenshots.
Using an iPhone without a wireless service plan
http://support.apple.com/kb/ht3406
Cheers,
- Judy -
So when I try to plug in My iPhone 4 to any plug it won't turn on or charge unless if I use an iPad charger. When I do get to turn it on. My Phone will Standby for a few seconds( While I'm Typing my 4-Digit Code) then it'll unlock and go to the home screen. Once I'm on the home Screen I can't Call, Text or Email anyone because my iPhone Can't detect any Wifi Hotspots and it also can't connect to my Service Provider, It'll just Say "Searching...". The non-internet apps work perfectly fine. So since I was able to use Just an iPad Charger to turn on my iPhone 4, I tried a Regular iPhone charger that were plugged into a wall or my computer. When its Plugged in, my iPhone will turn on ( Showing the Apple Logo) then turn back off. It'll constanly do this only when it's plugged into a Regular iPhone Charger, Either plugged into a Wall Socket or my Computer. So I Tried to Restore the Phone by using some of the Methods, given by other iPhone 4 Users, non of them worked. My iPhone won't Restart, Restore, Turn on without a Charger, Be Detected on my Computer and Detect my Service Provider. I really need help to fix my iPhone 4. I'm really not sure if it's a Malfunction with the Software on the iPhone, if my Sim Card is Broken. if the System is Corrupted but it only happens Rarely.
Thank you. If you're Reading this. Please Respond.
I need useful information.
If you'd like to Contact me, and give some useful information or ask me any Questions.
Contact me Through my EMAIL : [email protected]Not sure if this Term is Relevant towards an iPhone but, my iPhone won't Post unless if it's plugged into a Charger.
-
I've seen all the posts for fixing the wifi on the 4s, none of them work! So, who can tell me why my iPhone 4S cannot find any wifi when it used to find wifi, and when it does find a wifi network it can never connect? You think apple would have a clue how to fix it! Because turning the wifi on and off doesn't work, resorting network settings doesn't work, even restoring phone to factory default doesn't work...
Did not work. I've selected iMessage to ON and left it. After a few hours I recieved a message "activation unsuccessful. Turn on iMessage to try again". This has been going on for the past 3 days.
-
I upgraded my Iphone to IOS6, but now I can't connect it to itunes (10.6.3) because it is not upgraded. However, when I want to upgraded, it says that my computer (imac Mac OS 10.5.8) needs to be upgraded to another version. I can't find anything to help me out.
You need iTunes 10.7 or later.
To get this, you need Mac OS 10.6.8 or later.
You can get 10.6 Snow Leopard here -> http://store.apple.com/us/product/MC573/mac-os-x-106-snow-leopard -
I have a new ipad and everything works but can't connect to the app store. Itunes works and the wifi seems to be working but i get a blank white screen when i open the appstore. Nothing will load unter the features or charts tab so i cant download any apps. Purchased and updates tab loads fine. Any suggestions?
You would get better response from the iTunes community forum.
Have a nice day! -
I have had to restore my Ipod Touch and now I can't connect to anything on it. When it asks for my Apple ID it comes up with an error message and says that it can't connect to the server. I have checked my WiFi connection and its connected.
Hi there,
I would recommend taking a look at the troubleshooting steps found in the article below.
Can't connect to the iTunes Store
http://support.apple.com/kb/ts1368
-Griff W. -
I have the new IPad and can't connect via bluetooth to any of my apple devices (IPhone 4s and appleTV) neither from my new IPhone 4s. When I turn the Bluetooth on, both devices keep in searching mode... I don't know what to do now... Please help... I can't pair any device because they can't find whitin themselves.
Wmorlac wrote:
I have the new IPad and can't connect via bluetooth to any of my apple devices...
Correct... See Supported Bluetooth Profiles Here...
http://support.apple.com/kb/HT3647
Suggest you check the User Guides of your Devices to find the Method of what you are trying to do -
i downloaded the GV app to my iphone but i'm trying to set up the app and it says it can't connect to google when i try to sign in to my google account.... any ideas what's wrong? i can access my gmail account just fine with my gmail app on the same phone
What's a GV app?
Maybe you are looking for
-
How to print a bullet in smartforms?
Hi All, How to print a bullet in smartforms? I need it urgently. Any help would be appeciated. Regards, Mahesh.
-
Acrobat 7.0 Professional
Acrobat 7.0 is installed in this Imac running 10.6.8 but it will not load as I get a message "You can't open the application Adobe Acrobat 7.0 because it may be damaged or incomplete." What do I have to do,please? Because of the age of some of my pro
-
@ALIAS in FIX Statement
Hi, Can I use @ALIAS function in FIX statement? When i try to do it it says "Error: 1200315 Error parsing formula for [FIX STATEMENT] (line 1): invalid object type". If not is there any work around for it? Thanks.
-
Why wont my phone wont turn on
i was using my phone this morning, texting and calling people with no issue. my battery was at 30% so i didnt think battery power was an issue but after i put my phone down for a few minutes it stopped working. it wont charge, it wont turn on, it doe
-
SQLdeveloper can't connect to 10g Dbase
Hi, Everyone. I have been trying to make a connection to 10g database using oracle sqldeveloper (versions 1.2 , 1.5.0, 1.5.3, 1.5.4 and 1.5.5) for the past two weeks but to no avail. I always get the following error when using any of the abovenamed v