Can't ping wireless controller after firmware update to 7.0.240

I can figure out why I cant ping controller 10.1.99.100. Here is my controller config. It is connect to H3C 5800 switch. I have the switch config below as well. The port on the switch is on Native Vlan 1 untagged. Any help would be appreciated.
(Cisco Controller) show>interface summary
Interface Name                   Port Vlan Id  IP Address      Type    Ap Mgr Guest
ap-manager                       1    untagged  10.1.99.101     Static  Yes    No
external                             1    8             10.0.1.250       Dynamic No     No
internal                              1    93            10.42.156.66   Dynamic No     No
management                      1    untagged  10.1.99.100    Static  No     No
virtual                                   N/A  N/A      1.1.1.1           Static  No     No
H3C port configuration
Interface GigabitEthernet1/0/16
port link-mode bridge
port link-type hybrid
port hybrid vlan 2 8 92 to 93 tagged
port hybrid vlan 1 3 199 untagged
speed 100
duplex full

Cisco Controller) >show port summary
           STP   Admin   Physical   Physical   Link   Link
Pr  Type   Stat   Mode     Mode      Status   Status  Trap     POE   
1  Normal  Forw Enable  100 Full   100 Full   Up     Enable  N/A    
2  Normal  Disa Enable  Auto       Auto       Down   Enable  N/A    
3  Normal  Disa Enable  Auto       Auto       Down   Enable  N/A    
4  Normal  Forw Enable  Auto       100 Full   Up     Enable  N/A    
5  Normal  Disa Enable  Auto       Auto       Down   Enable  N/A    
6  Normal  Disa Enable  Auto       Auto       Down   Enable  N/A    
7  Normal  Forw Enable  Auto       100 Full   Up     Enable  Enable  (Power On )
8  Normal  Forw Enable  Auto       100 Full   Up     Enable  Enable  (Power On )
(Cisco Controller) >show interface man         detailed management
Interface Name................................... management
MAC Address...................................... 00:21:55:9a:4c:20
IP Address....................................... 10.1.99.100
IP Netmask....................................... 255.255.255.0
IP Gateway....................................... 10.1.99.254
External NAT IP State............................ Disabled
External NAT IP Address.......................... 0.0.0.0
VLAN............................................. 1        
Quarantine-vlan.................................. 0
Physical Port.................................... 1        
Primary DHCP Server.............................. Unconfigured
Secondary DHCP Server............................ Unconfigured
DHCP Option 82................................... Disabled
ACL.............................................. Unconfigured
AP Manager....................................... No
Guest Interface.................................. No
L2 Multicast..................................... Enabled

Similar Messages

  • Can't connect to Airport after firmware update

    Ever since I updated the firmware on my Airport I can't connect to it any more. I'm pretty sure I installed everything properly and reset the Airport several times but still no luck in connecting to it. Any suggestions?

    DomPoggi wrote:The Airport Utility said firmware on each Airport Express needs to be updated, so I did it. 
    Dom
    Firmware updates on the Express sometimes results in scrumbled settings.
    Check that WiFi is disabled on your MacBook.
    Then connect (preferabely with a LAN-Cable) the MacBook to the Express.
    Open Airport Utility on the Mac and switch to the Express.
    Use the wizzard to set up the Express from scratch or use manual setting zu check the settings.
    Lupunus

  • Can't connect to internet after firmware update?

    well last night i did a firmware update and now i can't connect to my network at home. i have a server running dhcp. so i gave the extreme a static ip in the range. dns and router ip are set to the servers ip. this all was working fine till last night. what am i doing wrong? i can't even log onto the server from my MBP. the APE is connected directly by ethernet to the server.
    thanks

    HI and welcome......
    On your iPad...
    Tap Settings / General / Reset / Reset Network Settings.
    That resets to factory default. You may be prompted for your network password.
    Hope that helps...
    Carolyn

  • Can't connect to WRT54G after firmware update

    I just tried to update the firmware on my WRT54G (version 8.0) and have not been able to connect to the router since then. The firmware said that it had been updated successfully, however I have been unable to connect since it reset itself, and the Ethernet and Internet LEDs are all constantly on even though nothing is connected (the power light on the other hand is behaving normally, not blinking or anything). I have tried resetting the router by holding down the reset button for 30 seconds, but this does not change anything, the router still cannot even be pinged. If anyone can give me any help at all with this, it will be very much appriciated. Thanks.

    It sounds like the router might already be dead.  But there is always hope that you might be able to revive it.
    You need to try again to reset the router to factory defaults.
    To reset your router to factory defaults, use the following procedure:
    1) Power down all computers, the router, and the modem, and unplug them from the wall.
    2) Disconnect all wires from the router.
    3) Power up the router and allow it to fully boot (1-2 minutes).
    4) Press and hold the reset button for 30 seconds, then release it, then let the router reset and reboot (2-3 minutes).
    5) Power down the router.
    6) Connect one computer by wire to port 1 on the router (NOT to the internet port).
    7) Power up the router and allow it to fully boot (1-2 minutes).
    8) Power up the computer (if the computer has a wireless card, make sure it is off).
    9) Try to ping the router. To do this, click the "Start" button > All Programs > Accessories > Command Prompt. A black DOS box will appear. Enter the following: "ping 192.168.1.1" (no quotes), and hit the Enter key. You will see 3 or 4 lines that start either with "Reply from ... " or "Request timed out." If you see "Reply from ...", your computer has found your router.
    10) Open your browser and point it to 192.168.1.1. This will take you to your router's login page. Leave the user name blank, and in the password field, enter "admin" (with no quotes). This will take you to your router setup page. Note the version number of your firmware (usually listed near upper right corner of screen). Exit your browser.
    If you get this far without problems, try the setup disk (or setup the router manually, if you prefer), and see if you can get your router setup and working.
    If you cannot get "Reply from ..." in step 9 above, your router is dead.
    If you get a reply in step 9, but cannot complete step 10, then either your router is dead or the firmware is corrupt. In this case, use the Linksys tftp.exe program to try to reload your router with the latest firmware. After reloading the firmware, repeat the above procedure starting with step 1.
    If you need additional help, please state your ISP, the make and model of your modem, your router's firmware version, and the results of steps 9 and 10. Also, if you get any error messages, copy them exactly and report back.
    Please let me know how things turn out for you.

  • Can't open Email Settings after firmware updated a...

    Hi,
    I've upgrated my E71 with new 3.00 firmware yesterday and then restored phone memory from saved backup (yes, restoring is still a great pain for Nokia phones owners - you know, not all the software installed restores and so on, but that's another question).
    Before this upgrade I had MfE and Nokia Email installed and one IMAP mailbox was set up in standard Messaging application. After restoring from backup Nokia Email was missing (backup problems I mentioned above) but I've reinstalled it successfully. MfE and Messaging mailbox also worked okay.
    But today suddenly I discovered that when I try to open Settings / Email menu item at Messaging app, this app crashes silently. Strange, but when I'm accessing Email Settings menu item being at mailbox tab, I can see this mailbox settings. but when I try to enter global email settings for all mailboxes from the app main menu, application crashes.
    I tried to add another mailbox using Settings Wizard - and it worked, additional mailbox appeared in Messaging app. But all the same with it - no access to global Settings / Email menu but  works okay when I open Email Settings directly from mailbox tab.
    The thing is that I need to remove mailboxes from Messaging App and it can be done through this unreachable global Settings / Email menu only.
    Another detail - when I change storage from phone memory to memory card in Settings / Other menu, my mailboxes disappear and the Settings / Email menu becomes accessible. And when I change storage back to phone memory, my two mailboxes are back again (and functional, as before), but when I try to open Settings / Email menu app crashes.
    Please advise, because I really have no idea what to do. I assume that there must be a way to remove mailboxes manually, but what is it?
    Regards, Yuriy.

    Well, the problem gone after I deleted MfE profile (I don't need it right now). This Settings menu is accessible again. Anyway, it was very strange and I can't predict if I will face it again after I add another MfE profile.

  • Airport Express doesn't connect to wireless network after firmware update

    Hi,
    I just updated the firmware on my Airport Express to 6.3 and now it will no longer join the network. I have tried reseting to the factory defaults and Airport Utility accepts all the information and shows the unit with a green dot next too it. However, the unit is still flashing amber and in the final step where the Utility tries to save the configuration the update fails and I get the following error message:
    An error occurred while reading the configuration.
    Please make sure your AirPort base station is plugged in and in range of your computer or connected via Ethernet and try again. (-6753).
    I am using an old style AirPort Extreme as a base station.
    Can anyone help?

    Wow, really no suggestions yet? This is a first for me, on the Apple Discussion boards!
    Can anyone help?

  • Can't ping wireless controller

    I can figure out why I cant ping controller management interface 10.1.99.100 even from Native Vlan. Here is my controller config. It is connect to H3C 5800 switch. I have the switch config below as well. The port on the switch is on Native Vlan 1 untagged. Any help would be appreciated.
    (Cisco Controller) show>interface summary
    Interface Name                   Port Vlan Id          IP Address      Type    Ap Mgr Guest
    ap-manager                         1    untagged        10.1.99.101     Static  Yes    No
    external                               1    8                   10.0.1.250      Dynamic No     No
    internal                                1    93                 10.42.156.66    Dynamic No     No
    management                        1    untagged       10.1.99.100     Static  No     No
    virtual 
    H3C port configuration
    Interface GigabitEthernet1/0/16
    port link-mode bridge
    port link-type hybrid
    port hybrid vlan 2 8 92 to 93 tagged
    port hybrid vlan 1 3 199 untagged
    speed 100
    duplex full

    Change the WLC vlan id to 0. Zero is untagged.
    Sent from Cisco Technical Support iPhone App

  • Problems after wireless router (WRT310n) firmware update.

    I updated the firmware on my wireless router (wrt310n) yesterday and now I am having major issues connecting my laptop to it via wireless.  After the update, I reset the router as well as unplugged the power source.  Once the update and everything was reset, I re-entered all my settings and set the computers back up using the LELA.  I go to change the laptop to wireless and it says it can't connect to it.  I did the LELA update on the laptop thinking that would fix it, but it didn't help.  However, the whole time I am able to connect to the router using a ethernet cable.  I turned off all of the encryption settings, firewalls, and broadcasted my SSID.  I searched this forum for some help and one topic suggested somethings, which I did, and I was able to connect wirelessly with the encryption.  I thought I was done and set-up, until later that evening.  I turned the computer back on only to see the same problem again.  I decided to deal with it the next day (today) by uninstalling LELA and just using Windows to configure my wireless settings.  As soon as I uninstalled LELA, entered the key into the Windows program, it worked like a charm.  Until tonight, when I turned on the computer.  Now I'm connecting to the network wirelessly, but it says "Limited or no connectivity."  Acting like there is no encryption key entered.  I go to "View Wireless Networks" and it says "WIndows cannot configure connection.  If you have another program to manage this wireless connection, use that software."  The thing is, I don't have another program on here to manage a wireless connection.  Sorry for the long post.  I figured if I didn't type everything out, people would have just asked me questions.  I had no problems with this router until I did the update yesterday.  If it can't be fixed, is there a way to revert back to the old firmware?  Thanks in advance.

    Well you should adjust the Wireless Settings on your router...
    Open an Internet Explorer browser page on your wired computer(desktop).In the address bar type - 192.168.1.1 and press Enter...Leave username blank & in password use admin in lower case...
    For Wireless Settings, please do the following : -
    Click on the Wireless tab
    - Here select manual configuration...Wireless Network mode should be mixed...
    - Provide a unique name in the Wireless Network Name (SSID) box in order to differentiate your network from your neighbours network...
    - Set the Radio Band to Standard-20MHz and change the Standard channel to 11-2.462GHz...Wireless SSID broadcast should be Enabled and then click on Save Settings...
    Please make a note of Wireless Network Name (SSID) as this is the Network Identifier...
    For Wireless Security : -
    Click on the Sub tab under Wireless > Wireless Security...
    Change the Wireless security mode to WEP, Encryption should be 64 bit.Leave the passphrase blank, don't type in anything...
    Under WEP Key 1 type in any 10 numbers please(numbers only and no letters eg: your 10 digit phone number) and click on save settings...
    Please make a note of WEP Key 1 as this is the Security Key for the Wireless Network...
    Click on Advanced Wireless Settings
    Change the Beacon Interval to 75 >>Change the Fragmentation Threshold to 2304, Change the RTS Threshold to 2304 >>Click on "Save Settings"...
    Before you attempt to connect to your wireless network you should first check your Programs menu if there is any Wireless Program(like 'Intel Proset' , 'Dell Wireless WLAN' , or anything that gives you a clue of a Wireless Program/Utility/Software)...You should use the Wireless Utility/Software(if any) to connect to your wireless network and not the Windows default Wireless Program to avoid any conflicts...

  • 3014 error i can't restore ipad after firmware update attempt

    3014 error i can't restore ipad after firmware update attempt

    See this thread with the same question.
    https://discussions.apple.com/thread/5045573?tstart=0

  • After firmware update to V2.0.03, the web UI dos not look right. (WRT160 V2)

    Hi
    After firmware update from V2.0.01 to V2.0.03, the web UI dos not look right. 
    I can't see menus, just version number and the basic setup page.
    Router Linksys WRT160 v2.
    Allan

    Hi
    Thanks for the reply.  
    I't works ok now.  
    Thanks again.
    Allan

  • Restoring after firmware update - Ways :)

    Hi All,
    Nowadays we are receiving quite a few complaints that customers are unable to restore the application after updating their firmware.  I would like all to discuss to come up with some ways to restore their applications after firmware update.
    Before updating firmware
    Customer can backup his phone using Nokia PC Suite's Content Copier application.
    He can store his Contacts and Messages using Nokia Communication Centre as .csv file or .txt file.
    For his Contacts he can sync with pc suite supported sync applications.
    Messages he can store in Memory card and he can make a backup of memory card in PC.
    If he is using Nokia PC Suite for his Multimedia items he can use Image Store if he is using Nokia PC Suite or Nokia Photos if he is using Nokia OVI Suite.
    For Music he can use Nokia Music Manager or Nokia Music.
    Once after updating his firmware, if he is unable to restore he can get those from above said applications.
    If his calendar entries are not restored(as in case of some of Nokia e 71s and Nokia N 95/95 8 GBs), for God's sake if he has got one more similar device(or device having switch application on phone), he can restore the backup file to another phone having switch application, then he can transfer his data (Contacts, Calenders etc ) to his original phone
    Dear Forum members, if you have got any other work around please let me know regarding the same, which will help our customers

    Hi,
    If you have issue in Nokia PC Suites, [subject to your phone's compatibility with Nokia OVI Suite 2.0.0.10 ],
    you can install Nokia OVI Suite 2.0.0.10 and check if you can take backup and restore it later.
    Also i would suggest to use USB for taking backup, since it will be faster than Bluetooth.  Also you can select one category at one time(say backup contacts alone, then Calendar, then messages etc and so on ....)
    Its better to skip memory card backup while backup-ing other Phone data for faster backup.  Memory card backup can be done separtely(since it wont be affetcted while updating firmware, users can safely remove memory card while updating firmware)
    Nowadays though recent phones has got UDP(User Data Prevention i.e., even if you update your phone's firmware, your data wont get erased ), still it is recommended to backup your phone data.
    Hope this could help
    I welcome our experts to add more details related to this topic.

  • Problems after firmware update 52.0.007

    Hi,
    I got my phone back after the shop fixed a problem and updated the firmware to the latest version 52.0.007.
    But now I have following problems:
    I can't get the calendar anymore to show up on the homescreen, even after checking the checkbox to do so
    The Radio app. is gone
    Does anyone has a solution for this?
    Iwan

    It may sound crazy but sometimes you need to "hard reset" device after firmware update (beware all data erased) by keying in *#7370# followed by 12345 (default Nokia lock code unless altered by yourself). Sometimes UDP = User Data Prersevation feature of 5800XM can carry over corrupt entries when updating.
    Happy to have helped forum with a Support Ratio = 42.5

  • Ovi Maps 3 don´t start after firmware update (6220...

    Hello!
    a few days ago I installed ovi maps 3 on my nokia 6220c and it works well. Later I updated the firmware from version 03.06 to 05.15.
    After firmware update ovi maps don´t start-> "Cannot open application. Install latest version from nokia.com/maps."
    But Nokia Map Updater says, there are no updates for my maps.
    What´s wrong?
    Can I reinstall Ovi Maps 3? Or is it possible to install Ovi Maps 3 new?
    thanks

    Hello!
    The Map Updater said: "there is no update for your phone" ...because maps 3 is already installed.
    But in the meantime I have found a solution!!
    I downloaded maps 2.0 from the German nokia page and installed it. Later I started Map Updater and could update to Maps 3 and now it works!!!
    I think the problem was: I first updated to Maps 3 and later updated the firmware. There was any older version of fixes included in the firmware update, so Maps 3 was damaged...
     thanks
    sorry for my bad English

  • Data recovery after firmware update

    Hi guys,
    does anyone know it it is possible to recover data after firmware update in N8? some data are preserved (videos) and some are lost (photos).
    thx.

    if you didn't backup them, there is no way to recover them
    Greece Nokia X6 RM-559 v40.0.002

  • TS3824 How can we install the iMac Graphics Firmware Update if the screen is white and I can't get to the Apple menu?

    How can I install the iMac Graphics Firmware Update 2.0, if the screen is white and I can't get to the Apple menu?  My computer has 5 vertical purple lines against white screen at startup before the Apple logo appears and the spinning gear...then everything disappears and the screen hangs on the white screen.  I have tried unplugging and removing all my peripherals and the COMMAND, OPTION, P & R set of keys and still nothing.  I have tried COMMAND C to start up from cd and it only tells me to turn off the computer and turn it back on.  I found information on Apple's Support pages regarding the iMac Graphics Firmware Update but I am unable to download and install if I can't get to the Apple menu.  Can anyone help?

    You may have hardware problem, I think a visit to your local Apple Store or AASP is in order.

Maybe you are looking for