Catalyst 5505 With Catalyst 2948G

I have connected C5505 (core switch) to C2948G (edge switch).The problem i am facing is the vtp Server(C5505) would not update the client(C2948G).May I know what is the possibility?
Thanks
Best Regards,
Steven Hoo

The main reasons I can think of are:
- no trunk between the switches
- different VTP domain configured
- different VTP password
- different VTP version
- client already has higher config revision number
Before you connect it, make sure the config revision number on the new switch is less than that of the server, and that the new switch is not a server, otherwise you are in for a nasty surprise. For good measure, take the new switch out of the domain and in again - this should set its revision down to zero.
Kevin Dorrell
Luxembourg

Similar Messages

ASA 5505 with Backup ISP

I am working with a client that currently has an ASA 5505 with two ISPs for failover using a tracked interface. I would like to configure logging so that the ASA will email us when the Primary ISP goes down and fails over to the backup. Here is what I have so far...
interface Ethernet0/0
switchport access vlan 2
interface Ethernet0/1
switchport access vlan 12
interface Ethernet0/2
speed 100
duplex full
interface Ethernet0/3
switchport access vlan 22
speed 100
duplex full
interface Ethernet0/4
switchport access vlan 22
interface Ethernet0/5
switchport access vlan 22
interface Ethernet0/6
interface Ethernet0/7
interface Vlan1
nameif inside
security-level 100
ip address 192.168.0.1 255.255.255.0
interface Vlan2
nameif outside
security-level 0
ip address 50.76.252.33 255.255.255.248
interface Vlan12
nameif backup
security-level 0
ip address 168.93.174.130 255.255.255.248
interface Vlan22
nameif Phones
security-level 100
ip address 192.168.3.1 255.255.255.0
logging enable
logging buffered warnings
logging asdm warnings
logging from-address [email protected]
logging recipient-address [email protected] level errors
route outside 0.0.0.0 0.0.0.0 DG-Commcast 128 track 1
route backup 0.0.0.0 0.0.0.0 DG-FirstCom 255
sla monitor 123
type echo protocol ipIcmpEcho 73.120.130.1 interface outside
frequency 10
sla monitor schedule 123 life forever start-time now
track 1 rtr 123 reachability
Let me know if you need any more info from the config; it's quite long and not sure what all is needed...
The primary interface is Outside and the backup is obviously Backup
Thanks!
Tony

Hi Tony,
As long as the event covered under 'errors' list - inaddition to the above config, you need to add..
loging mail errors
smtp-server
Check the below link for more information on ASA message logging..
http://www.cisco.com/en/US/products/hw/vpndevc/ps2030/products_configuration_example09186a00805a2e04.shtml
hth
MS

Catalyst 2948G: boot error

Does the following indicate a hardware problem? Can it be fixed? Please advise. Thanks.
This is the output when the switch is powered on and enters the "loading diagnostics" phase.
Loading diagnostics...
Power-on-self-test for Module 1: WS-X2948
Status: (. = Pass, F = Fail)
processor: . cpu sdram: . temperature sensor: .
enet console port: . nvram: . *** ERROR *** ttl=1 addr=70001210
expected=0000000000000242 actual=0000000400000242
*** ERROR *** ttl=2 addr=70001230 expected=0000000000000246 actual=0000000400000
246
*** ERROR *** ttl=3 addr=70001250 expected=000000000000024a actual=0000000400000
24a
*** ERROR *** ttl=4 addr=70001270 expected=000000000000024e actual=0000000400000
24e
*** ERROR *** ttl=5 addr=70001290 expected=0000000000000252 actual=0000000400000
252
*** ERROR *** ttl=6 addr=700012b0 expected=0000000000000256 actual=0000000400000
256
switch sram: F
switch registers: . switch port 6: F switch port 7: F
switch bandwidth: .
Module 1 Failed
After the switch boots, I get the message to: Use 'show test 1' to see results of tests.
Console> (enable) show test 1
Module 1 : 0-port Switching Supervisor
Network Management Processor (NMP) Status: (. = Pass, F = Fail, U = Unknown)
Control Processor Status:
DRAM : . EEPROM : . FLASH : . NVRAM : .
SX1000:
Register : . Network Memory : F
Mgmt Port Loopback Status: .

This is definitely a hardware problem. Appearently, your only hope is that it's a temperature related problem.
Therefore you could try to take the module out and remove the dirt from the last years. It might give your switch some more air and reseating the connectors isn't that bad either. If it doesn't help, please keep in mind that eventually we all pass away! ;-)
Regards,
Leo

Cisco asa 5505 with Router 881w Configuration Help

Hello all,
I'm having trouble setting up a second vlan to route to the internet. I have a Cisco ASA 5505 connected to my ISP(OUTSIDE) and a Cisco 881w (INSIDE) router in the back of my firewall. My vlan 10 with the network 192.168.5.1 255.255.255.0 works with pat, however vlan 15 that is on my 881w router does not route to the internet at all. I can only ping from 192.168.15.15 network to 192.168.5.1 I would like some advice on how can I make this set up work. Attached with this discussion is a picture of my topology.
Thanks in advance.
here are the show runs:
Cisco ASA 5505 show run:
ASA Version 8.3(1)
names
interface Vlan1
no nameif
no security-level
no ip address
interface Vlan5
mac-address xxxx.xxxx.xxxx
nameif OUTSIDE
security-level 0
ip address dhcp setroute
interface Vlan10
nameif INSIDE
security-level 100
ip address 192.168.5.1 255.255.255.0
interface Ethernet0/0
switchport access vlan 5
interface Ethernet0/1
switchport access vlan 10
interface Ethernet0/2
interface Ethernet0/3
shutdown
interface Ethernet0/4
shutdown
interface Ethernet0/5
shutdown
interface Ethernet0/6
shutdown
interface Ethernet0/7
shutdown
ftp mode passive
clock timezone CST -6
clock summer-time CDT recurring
object network INTERNAL_LAN
subnet 192.168.5.0 255.255.255.0
object network PRIVATE_LAN_192
subnet 192.168.15.0 255.255.255.224
description PRIVATE_LAN_192
access-list INSIDE_access_in extended permit ip any any
access-list INSIDE_access_in extended deny ip any any
access-list OUTSIDE_access_in extended permit ip any any
access-list OUTSIDE_access_in extended deny ip any any
pager lines 24
logging enable
mtu OUTSIDE 1500
mtu INSIDE 1500
ip verify reverse-path interface OUTSIDE
ip verify reverse-path interface INSIDE
no failover
icmp unreachable rate-limit 1 burst-size 1
no asdm history enable
arp timeout 14400
object network INTERNAL_LAN
nat (INSIDE,OUTSIDE) dynamic interface
object network PRIVATE_LAN_192
nat (INSIDE,OUTSIDE) dynamic interface
access-group OUTSIDE_access_in in interface OUTSIDE
access-group INSIDE_access_in in interface INSIDE
route INSIDE 192.168.15.0 255.255.255.224 192.168.5.2 1
dynamic-access-policy-record DfltAccessPolicy
http server enable
dhcpd dns 8.8.8.8 75.75.76.76
dhcpd address 192.168.5.10-192.168.5.100 INSIDE
dhcpd enable INSIDE
Router 881w show run:
Current configuration : 4912 bytes
version 12.4
no ip source-route
ip dhcp excluded-address 192.168.15.1 192.168.15.10
ip dhcp pool PRIVATE_LAN
network 192.168.15.0 255.255.255.224
interface FastEthernet0
switchport trunk allowed vlan 1,15,1002-1005
switchport mode trunk
interface FastEthernet1
interface FastEthernet2
interface FastEthernet3
interface FastEthernet4
ip address 192.168.5.2 255.255.255.0
duplex auto
speed auto
interface wlan-ap0
description Service module interface to manage the embedded AP
no ip address
arp timeout 0
interface Wlan-GigabitEthernet0
description Internal switch interface connecting to the embedded AP
interface Vlan1
no ip address
interface Vlan15
ip address 192.168.15.1 255.255.255.224
no ip forward-protocol nd
ip route 0.0.0.0 0.0.0.0 FastEthernet4
no ip http server
ip http authentication local
ip http secure-server

The cable modem does not have any configuration. I cant add any to it. Its a cisco dpc3008. From vlan 10 i have no problem to get to the internet with the above configuration. My problem is just vlan 15.

Catalyst login issue

I have a strange problem with all catalysts (2948g's, 5500's) on our network. We just moved to an ACS for RADIUS authentication to these switches so I used Ciscoworks to push out the config changes to the switches (all it did was to change the IP address of the RADIUS server on the configs).
Ever since, when I log into one of the switches I'm placed directly into enable mode even though the switches are configured to ask for the local password first.
Here's the output for a show authentication:
Login Authentication: Console Session Telnet Session Http Session
tacacs disabled disabled disabled
radius enabled(primary) enabled(primary) disabled
kerberos disabled disabled disabled
local enabled enabled enabled(primary)
attempt limit 3 3 -
lockout timeout (sec) disabled disabled -
Enable Authentication: Console Session Telnet Session Http Session
tacacs disabled disabled disabled
radius disabled disabled disabled
kerberos disabled disabled disabled
local enabled(primary) enabled(primary) enabled(primary)
attempt limit 3 3 -
lockout timeout (sec) disabled disabled -
Any ideas? I have the enablepass configured....

Does it have the same behavior when different IDs are used to login or is it just happening with your ID?
You might want to check how the IDs are defined in radius and what privilege level is associated with them.
It might also help if you could post the aaa and radius parts of your config.
HTH
Rick

Problem with ASA 5505

Good morning,
I'm having the following problem. I configured a ASA 5505 with VPN and a VPN Remote Access Site-to-site. Everything is working, but when I reload the ASA does not work anymore VPNs, Remote Access error 412 and the Site-to-site does not connect more to solve, I have to reset and reconfigure the ASA. This is happening dopo updating the ASA, I have version 842-k8 and asdm645-106.
Does anyone have any idea what can be?
Thank you.
Running-config:
: Saved
: Written by master at 10:34:14.839 BRDT Mon Oct 10 2011
ASA Version 8.4(2)
hostname ciscoasa
domain-name default.domain.invalid
enable password 2KFQnbNIdI.2KYOU encrypted
passwd 2KFQnbNIdI.2KYOU encrypted
names
interface Ethernet0/0
switchport access vlan 2
interface Ethernet0/1
interface Ethernet0/2
interface Ethernet0/3
interface Ethernet0/4
interface Ethernet0/5
interface Ethernet0/6
interface Ethernet0/7
interface Vlan1
nameif inside
security-level 0
ip address 172.16.0.140 255.255.252.0
interface Vlan2
nameif outside
security-level 0
pppoe client vpdn group gvt
ip address pppoe setroute
boot system disk0:/asa842-k8.bin
ftp mode passive
clock timezone BRST -3
clock summer-time BRDT recurring 2 Sun Oct 0:00 3 Sun Feb 0:00
dns server-group DefaultDNS
domain-name default.domain.invalid
same-security-traffic permit inter-interface
same-security-traffic permit intra-interface
object network NETWORK_OBJ_172.16.0.0_22
subnet 172.16.0.0 255.255.252.0
object network NETWORK_OBJ_172.16.0.128_26
subnet 172.16.0.128 255.255.255.192
object network NETWORK_OBJ_20.0.0.0_24
subnet 20.0.0.0 255.255.255.0
object network NETWORK_OBJ_172.16.11.0_24
subnet 172.16.11.0 255.255.255.0
object-group network obj_any
access-list 1 standard permit 172.16.0.0 255.255.252.0
access-list 1 standard permit 20.0.0.0 255.255.255.0
access-list outside_cryptomap extended permit ip 172.16.0.0 255.255.252.0 20.0.0.0 255.255.255.0
access-list outside_cryptomap_1 extended permit ip 172.16.0.0 255.255.252.0 172.16.11.0 255.255.255.0
pager lines 24
logging asdm informational
mtu inside 1500
mtu outside 1500
ip local pool pool 172.16.0.150-172.16.0.160 mask 255.255.252.0
no failover
icmp unreachable rate-limit 1 burst-size 1
asdm image disk0:/asdm-645-106.bin
no asdm history enable
arp timeout 14400
nat (inside,outside) source static NETWORK_OBJ_172.16.0.0_22 NETWORK_OBJ_172.16.0.0_22 destination static NETWORK_OBJ_172.16.0.128_26 NETWORK_OBJ_172.16.0.128_26 no-proxy-arp route-lookup
nat (inside,outside) source static NETWORK_OBJ_172.16.0.0_22 NETWORK_OBJ_172.16.0.0_22 destination static NETWORK_OBJ_20.0.0.0_24 NETWORK_OBJ_20.0.0.0_24 no-proxy-arp route-lookup
nat (inside,outside) source static NETWORK_OBJ_172.16.0.0_22 NETWORK_OBJ_172.16.0.0_22 destination static NETWORK_OBJ_172.16.11.0_24 NETWORK_OBJ_172.16.11.0_24 no-proxy-arp route-lookup
nat (inside,outside) after-auto source dynamic any interface
route outside 172.16.11.0 255.255.255.0 187.16.33.131 10
timeout xlate 3:00:00
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
timeout floating-conn 0:00:00
dynamic-access-policy-record DfltAccessPolicy
user-identity default-domain LOCAL
http server enable
http 172.16.0.0 255.255.252.0 inside
no snmp-server location
no snmp-server contact
crypto ipsec ikev1 transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-DES-SHA esp-des esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-3DES-SHA esp-3des esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-DES-MD5 esp-des esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-3DES-MD5 esp-3des esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-AES-256-SHA esp-aes-256 esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-AES-128-SHA esp-aes esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-AES-128-MD5 esp-aes esp-md5-hmac
crypto ipsec ikev2 ipsec-proposal DES
protocol esp encryption des
protocol esp integrity sha-1 md5
crypto ipsec ikev2 ipsec-proposal 3DES
protocol esp encryption 3des
protocol esp integrity sha-1 md5
crypto ipsec ikev2 ipsec-proposal AES
protocol esp encryption aes
protocol esp integrity sha-1 md5
crypto ipsec ikev2 ipsec-proposal AES192
protocol esp encryption aes-192
protocol esp integrity sha-1 md5
crypto ipsec ikev2 ipsec-proposal AES256
protocol esp encryption aes-256
protocol esp integrity sha-1 md5
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set ikev1 transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA ESP-3DES-MD5 ESP-DES-SHA ESP-DES-MD5
crypto map outside_map 1 match address outside_cryptomap
crypto map outside_map 1 set peer 189.11.56.237
crypto map outside_map 1 set ikev1 transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA ESP-3DES-MD5 ESP-DES-SHA ESP-DES-MD5
crypto map outside_map 1 set ikev2 ipsec-proposal AES256 AES192 AES 3DES DES
crypto map outside_map 2 match address outside_cryptomap_1
crypto map outside_map 2 set peer 187.16.33.131
crypto map outside_map 2 set ikev1 transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA ESP-3DES-MD5 ESP-DES-SHA ESP-DES-MD5
crypto map outside_map 2 set ikev2 ipsec-proposal DES 3DES AES AES192 AES256
crypto map outside_map 65535 ipsec-isakmp dynamic SYSTEM_DEFAULT_CRYPTO_MAP
crypto map outside_map interface outside
crypto ikev2 policy 1
encryption aes-256
integrity sha
group 5 2
prf sha
lifetime seconds 86400
crypto ikev2 policy 10
encryption aes-192
integrity sha
group 5 2
prf sha
lifetime seconds 86400
crypto ikev2 policy 20
encryption aes
integrity sha
group 5 2
prf sha
lifetime seconds 86400
crypto ikev2 policy 30
encryption 3des
integrity sha
group 5 2
prf sha
lifetime seconds 86400
crypto ikev2 policy 40
encryption des
integrity sha
group 5 2
prf sha
lifetime seconds 86400
crypto ikev2 enable outside
crypto ikev1 enable outside
crypto ikev1 ipsec-over-tcp port 10000
crypto ikev1 policy 10
authentication crack
encryption aes-256
hash sha
group 2
lifetime 86400
crypto ikev1 policy 20
authentication rsa-sig
encryption aes-256
hash sha
group 2
lifetime 86400
crypto ikev1 policy 30
authentication pre-share
encryption aes-256
hash sha
group 2
lifetime 86400
crypto ikev1 policy 40
authentication crack
encryption aes-192
hash sha
group 2
lifetime 86400
crypto ikev1 policy 50
authentication rsa-sig
encryption aes-192
hash sha
group 2
lifetime 86400
crypto ikev1 policy 60
authentication pre-share
encryption aes-192
hash sha
group 2
lifetime 86400
crypto ikev1 policy 70
authentication crack
encryption aes
hash sha
group 2
lifetime 86400
crypto ikev1 policy 80
authentication rsa-sig
encryption aes
hash sha
group 2
lifetime 86400
crypto ikev1 policy 90
authentication pre-share
encryption aes
hash sha
group 2
lifetime 86400
crypto ikev1 policy 100
authentication crack
encryption 3des
hash sha
group 2
lifetime 86400
crypto ikev1 policy 110
authentication rsa-sig
encryption 3des
hash sha
group 2
lifetime 86400
crypto ikev1 policy 120
authentication pre-share
encryption 3des
hash sha
group 2
lifetime 86400
crypto ikev1 policy 130
authentication crack
encryption des
hash sha
group 2
lifetime 86400
crypto ikev1 policy 140
authentication rsa-sig
encryption des
hash sha
group 2
lifetime 86400
crypto ikev1 policy 150
authentication pre-share
encryption des
hash sha
group 2
lifetime 86400
telnet timeout 5
ssh timeout 5
console timeout 0
vpdn group gvt request dialout pppoe
vpdn group gvt localname *******@turbonetpro
vpdn group gvt ppp authentication pap
vpdn username *******@turbonetpro password *****
dhcpd auto_config outside
dhcpd address 172.16.0.144-172.16.1.143 inside
threat-detection basic-threat
threat-detection statistics access-list
no threat-detection statistics tcp-intercept
webvpn
group-policy crv internal
group-policy crv attributes
dns-server value 172.16.0.253 8.8.8.8
vpn-tunnel-protocol ikev1
split-tunnel-policy tunnelspecified
split-tunnel-network-list value 1
default-domain value crvnatural.com.br
group-policy GroupPolicy_189.11.56.237 internal
group-policy GroupPolicy_189.11.56.237 attributes
vpn-filter value 1
vpn-tunnel-protocol ikev1 ikev2
group-policy GroupPolicy_187.16.33.131 internal
group-policy GroupPolicy_187.16.33.131 attributes
vpn-filter value 1
vpn-tunnel-protocol ikev1 ikev2
username master password kWH7f2vqtjMEg2Yp encrypted
tunnel-group crv type remote-access
tunnel-group crv general-attributes
default-group-policy crv
dhcp-server 172.16.0.253
tunnel-group crv ipsec-attributes
ikev1 pre-shared-key *****
tunnel-group 189.11.**.*** type ipsec-l2l
tunnel-group 189.11.**.*** general-attributes
default-group-policy GroupPolicy_189.11.**.***
tunnel-group 189.11.**.*** ipsec-attributes
ikev1 pre-shared-key *****
ikev2 remote-authentication pre-shared-key ****
ikev2 local-authentication pre-shared-key *****
tunnel-group 187.16.33.*** type ipsec-l2l
tunnel-group 187.16.33.*** general-attributes
default-group-policy GroupPolicy_187.16.33.***
tunnel-group 187.16.33.*** ipsec-attributes
ikev1 pre-shared-key ******
ikev2 remote-authentication pre-shared-key *****
ikev2 local-authentication pre-shared-key *****
class-map inspection_default
match default-inspection-traffic
policy-map type inspect dns preset_dns_map
parameters
message-length maximum client auto
message-length maximum 512
policy-map global_policy
class inspection_default
inspect dns preset_dns_map
inspect ftp
inspect h323 h225
inspect h323 ras
inspect rsh
inspect rtsp
inspect esmtp
inspect sqlnet
inspect skinny
inspect sunrpc
inspect xdmcp
inspect sip
inspect netbios
inspect tftp
inspect ip-options
service-policy global_policy global
prompt hostname context
call-home
profile CiscoTAC-1
no active
destination address http https://tools.cisco.com/its/service/oddce/services/DDCEService
destination address email [email protected]
destination transport-method http
subscribe-to-alert-group diagnostic
subscribe-to-alert-group environment
subscribe-to-alert-group inventory periodic monthly
subscribe-to-alert-group configuration periodic monthly
subscribe-to-alert-group telemetry periodic daily
Cryptochecksum:50ed6f55182534a2429d065a26e9b45c
: end

David,
In order to understand why LDAP is not working run a "debug ldap 255" and then try to login or run a AAA test.
Attach the output to find out the issue.
Please check this out as well, to make sure that you have the correct settings:
ASA 8.0: Configure LDAP Authentication for WebVPN Users
HTH.
Portu.

ASA 5505 - 2 Internet Connections, Problems with the Default Route

Hey there,
i have a Problem at a Customer Site at the moment. The customer uses an ASA 5505 with two internet connections attached to it. On the first connection (which is the only one in use at the moment) he has some Static-PAT's from Outside to Inside where he translates different services to the internal servers. He also has a site-2-site VPN terminating there and AnyConnect.
He now wants to switch the Internet Traffic from Inside to the new Internet Connection. Therefore changing the default route to that new ISPs Gateway. The problem now is, that no traffic recieved on the old "outside" Interface is transmitted back out of that old "outside" Interface. And this happens although the "same-security permit intra-interface" command is set.
Can you tell me what's wrong here? For every Static-PAT from outside to inside there is also a dynamic PAT from inside to outside. But the ASA seems to ignore this. I have not looked into the Logs yet, was too busy finding the problem because i had no real time window to test on the productive ASA.
Can it be achieved in any way? Having a default route on the ASA which leads any traffic to the second internet connection while still having connections on the first internet connection where no explicit route can be set? Because connections arrive from random IPs?
Many thanks for your help in advance!
Steffen

Phillip, indeed , I have as well read may comments,it all depends on your environment as they all differ from one another, you best bet is to have a good solid plan for upgrade and fall back. You do have a justification to upgrade for features needed, so I would suggest the following:
1- Do a search again in forum for ASA code upgrades and look at comments from users that have gone through this process and note their impact in fuctionality if any. I believe this is good resource to collect information .
2- Very important , look into release notes for a particular version. For example version 8.0, look into open CAVEATS usually at the end of the link page, reading the open bugs gives you clues what has not yet been resolved for that particular code and if in fact could impact you in your environment, it is possible that a particular bug does not realy apply to your environment becuase you have yet not implemented that particualr configuration. Usually we all try to aim towards a GD (General Deployment) code which is what we all understand is most stable but not necesarily means you have to be stack in that code waiting for another GD release, in my personal experience I have upgraded our firewall from 7.2 to 8.0(3) long ago and had no issues, and recently upgraded to 8.0(4)when it was first release in August this year.
Release notes
http://www.cisco.com/en/US/products/ps6120/prod_release_notes_list.html
3- AS a good practice precaution -
a-Backup firewall configs in clear text as well as via tftp code.
b-Backup running code and ASDM version code currently running in firewall.
c- Save the output of " show version " to have as reference for all the feature licenses you currently have running as asll as activation keys - good info to have to compare with after upgrade.
d- Ensure that the code you will be using to upgrade also uses correct ASDM version code.
I think with thorough assesment and preparation you can indeed minimize impact.
Rgds
Jorge

Cisco ASA 5505 - problem with negotiating IP address from PPPoE

Hi all,
I have problem with negotiating IP address from PPPoE. There is following design: ISP providing vDSL ending on VDSL modem in bridge mode. Behind brigde modem is ASA 5505 terminting PPPoE on OUTSIDE. Everything works fine except negotiating IP address from PPPoE server.
I have configured ASA 5505 with (ASA Version 9.2(2)4) for PPPoE like this [1.]. But If i try to "show" IP address on OUTSIDE interface a get this [2.], ok strange but let's continue. If list "show vpdn pppinterface id 1" i get this [3.]. Seems that I got public IP addres what was right, but this IP address was not associated with interface OUTSIDE?
Well, if I set IP address manually like this [4.] and also set a default route everything works fine but what will happen when ISP change reservation for my IP address or default gateway.
I have tried different version of ASA OS like 8.4, 9.1 but without luck.
Can anybody help me. Thanks a lot.
Regards
Karel
[1.]
interface Vlan100
description >>VLAN pro pripojeni do internetu<<
nameif OUTSIDE
security-level 0
pppoe client vpdn group O2
ip address pppoe setroute
vpdn group O2 request dialout pppoe
vpdn group O2 localname O2
vpdn group O2 ppp authentication chap
vpdn username O2 password *****
interface Ethernet0/0
description >>uplink O2 vDSL<<
switchport access vlan 100
[2.]
ciscoasa(config-if)# show ip address vlan 100 pppoe
ciscoasa(config-if)# 0.0.0.0 255.255.255.255 on Interface: OUTSIDE
ciscoasa(config-if)# show interface vlan 100 detail
Interface Vlan2 "OUTSIDE", is up, line protocol is up
Hardware is EtherSVI, BW 100 Mbps, DLY 100 usec
        Description: >>VLAN pro pripojeni do internetu<<
        MAC address f44e.05d0.6c17, MTU 1492
        IP address unassigned
Traffic Statistics for "OUTSIDE":
        28 packets input, 1307 bytes
        31 packets output, 721 bytes
        0 packets dropped
      1 minute input rate 0 pkts/sec, 3 bytes/sec
      1 minute output rate 0 pkts/sec, 1 bytes/sec
      1 minute drop rate, 0 pkts/sec
      5 minute input rate 0 pkts/sec, 0 bytes/sec
      5 minute output rate 0 pkts/sec, 0 bytes/sec
      5 minute drop rate, 0 pkts/sec
Control Point Interface States:
        Interface number is 15
        Interface config status is active
        Interface state is active
[3.]
ciscoasa(config-if)# show vpdn pppinterface id 1
PPP virtual interface id = 1
PPP authentication protocol is CHAP
Server ip address is 88.103.200.41
Our ip address is 85.71.188.158
Transmitted Pkts: 20, Received Pkts: 16, Error Pkts: 0
MPPE key strength is None
MPPE_Encrypt_Pkts: 0, MPPE_Encrypt_Bytes: 0
MPPE_Decrypt_Pkts: 0, MPPE_Decrypt_Bytes: 0
Rcvd_Out_Of_Seq_MPPE_Pkts: 0
ciscoasa(config-if)# show vpdn session state
%No active L2TP tunnels
%No active PPTP tunnels
PPPoE Session Information (Total tunnels=1 sessions=1)
SessID TunID Intf     State       Last Chg
22298      2 OUTSIDE SESSION_UP 561 secs
[4.]
interface Vlan100
description >>VLAN pro pripojeni do internetu<<
nameif OUTSIDE
security-level 0
pppoe client vpdn group O2
ip address 85.71.188.158 255.255.255.255 pppoe setroute
route OUTSIDE 0.0.0.0 0.0.0.0 88.103.200.41 1

You're right that the ACL should not affect otherwise allowed communications to the interface address.
Try disabling the ip audit feature on your outside interface.
no ip audit interface OUTSIDE AP_OUTSIDE_INFO
no ip audit interface OUTSIDE AP_OUTSIDE_ATTACK

Problem with saving config on asa 5505

I have asa 5505 with 512mb , i am trying to save ios on it but i failed many times , I have sandisk 2GB and i formatted with windows on fat but every time i see disk0 failed , any ideas what is the problem ?
Thanks

I have asa 5505 with 512mb , i am trying to save ios on it but i failed many times , I have sandisk 2GB and i formatted with windows on fat but every time i see disk0 failed , any ideas what is the problem ?
Thanks

ASA 5505 Problem with outbound PPTP-connection on non-native vlan

Hi, why am I not being able to make a PPTP connection on vlan80 (trunked to AP Cisco 1142N) compared to vlan10? And yes, I've configured the "
inspect pptp"
ASA 5505 with sec plus license

Hi mate,
I don't know how to solve your problem but I strongly reccommend you to remove your password from the first post and to update it on your ASA device

Problem with asa 5505 routing,nating

i have the asa 5505 with asdm 6.4(5). my inside lan is 192.168.0.0/24. the outside of asa is connected on lan 10.13.74.0/24 and i need over lan 10.13.74.0/24 connect on lan 10.15.100.0/24. i puted nat rule on asa 5505 and acl rule and users from lan 10.15.100.0/24 can connect on my server, but i can't connect on from inside of asa connecet on lan 10.15.100.0/24 and 10.13.74.0/24. my configuration asa is
Result of the command: "show running-config": Saved:ASA Version 8.4(2) !hostname ciscoasaenable password 8Ry2YjIyt7RRXU24 encryptedpasswd 2KFQnbNIdI.2KYOU encryptednames!interface Ethernet0/0 switchport access vlan 2!interface Ethernet0/1 switchport access vlan 3!interface Ethernet0/2!interface Ethernet0/3!interface Ethernet0/4!interface Ethernet0/5!interface Ethernet0/6!interface Ethernet0/7!interface Vlan1 nameif inside security-level 100 ip address 192.168.0.17 255.255.255.0 !interface Vlan2 nameif outside security-level 0 ip address 10.13.74.33 255.255.255.0 !ftp mode passiveobject network obj_any subnet 0.0.0.0 0.0.0.0object network server host 192.168.0.20object service ParagrafLex service tcp source eq 6190 destination eq 6190 object network sharepoint host 192.168.0.22access-list outside_access_in extended permit ip host 10.13.74.35 any access-list outside_access_in_1 extended permit ip any object server access-list outside_access_in_1 extended permit object ParagrafLex 10.15.100.0 255.255.255.0 object server access-list outside_access_in_1 extended permit object ParagrafLex any object server pager lines 24logging asdm informationalmtu inside 1500mtu outside 1500icmp unreachable rate-limit 1 burst-size 1no asdm history enablearp timeout 14400!object network obj_any nat (inside,outside) dynamic interfaceobject network server nat (any,any) static 10.13.74.34access-group outside_access_in in interface outside control-planeaccess-group outside_access_in_1 in interface outsideroute inside 0.0.0.0 0.0.0.0 10.13.74.1 1timeout xlate 3:00:00timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolutetimeout tcp-proxy-reassembly 0:01:00timeout floating-conn 0:00:00dynamic-access-policy-record DfltAccessPolicyuser-identity default-domain LOCALhttp server enablehttp 192.168.1.0 255.255.255.0 insidehttp 10.13.74.0 255.255.255.0 outsideno snmp-server locationno snmp-server contactsnmp-server enable traps snmp authentication linkup linkdown coldstart warmstarttelnet timeout 5ssh timeout 5console timeout 0dhcpd auto_config outside!threat-detection basic-threatthreat-detection statistics access-listno threat-detection statistics tcp-interceptwebvpn!class-map inspection_default match default-inspection-traffic!!policy-map type inspect dns preset_dns_map parameters message-length maximum client auto message-length maximum 512policy-map global_policy class inspection_default inspect dns preset_dns_map inspect ftp inspect h323 h225 inspect h323 ras inspect rsh inspect rtsp inspect esmtp inspect sqlnet inspect skinny inspect sunrpc inspect xdmcp inspect sip inspect netbios inspect tftp inspect ip-options !service-policy global_policy globalprompt hostname context no call-home reporting anonymousCryptochecksum:791a1fa6b6fcccaa3177fed821d1f392: end
what i do that connect on lan 10.15.100.0/24. i cant ping my outside interface, puted rules on acl, i enabled sevice policy rule for icmp ,but nothing. pleas help me
thanks

my configuration asa 5505 is now
Result of the command: "show running-config"
: Saved
ASA Version 8.4(2)
hostname ciscoasa
enable password 8Ry2YjIyt7RRXU24 encrypted
passwd 2KFQnbNIdI.2KYOU encrypted
names
interface Ethernet0/0
switchport access vlan 2
interface Ethernet0/1
interface Ethernet0/2
interface Ethernet0/3
interface Ethernet0/4
interface Ethernet0/5
interface Ethernet0/6
interface Ethernet0/7
interface Vlan1
nameif inside
security-level 100
ip address 192.168.0.17 255.255.255.0
interface Vlan2
nameif outside
security-level 0
ip address 10.13.74.33 255.255.255.0
ftp mode passive
object network obj_any
subnet 0.0.0.0 0.0.0.0
object network server
host 192.168.0.20
object service ParagrafLex
service tcp source eq 6190 destination eq 6190
object network sharepoint
host 192.168.0.22
object network uzzpro
range 10.13.74.40 10.13.74.45
object network share
host 192.168.0.22
object-group network internalnetwork
network-object 192.168.0.0 255.255.255.0
object-group network uzzpro-1
network-object object uzzpro
access-list outside_access_in extended permit ip host 10.13.74.35 any
access-list outside_access_in_1 extended permit ip any object server
access-list outside_access_in_1 extended permit object ParagrafLex 10.15.100.0 255.255.255.0 object server
access-list outside_access_in_1 extended permit object ParagrafLex any object server
access-list outside_access_in_1 extended permit ip any object share
access-list outside_access_in_1 extended permit icmp any object sharepoint echo-reply
access-list inside_access_out extended permit ip any any
pager lines 24
logging asdm informational
mtu inside 1500
mtu outside 1500
icmp unreachable rate-limit 1 burst-size 1
no asdm history enable
arp timeout 14400
object network obj_any
nat (inside,outside) dynamic interface
object network server
nat (inside,outside) static 10.13.74.34
object network share
nat (any,any) static 10.13.74.39
access-group inside_access_out out interface inside
access-group outside_access_in in interface outside control-plane
access-group outside_access_in_1 in interface outside
route inside 0.0.0.0 0.0.0.0 10.13.74.1 1
timeout xlate 3:00:00
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
timeout floating-conn 0:00:00
dynamic-access-policy-record DfltAccessPolicy
user-identity default-domain LOCAL
http server enable
http 192.168.1.0 255.255.255.0 inside
http 10.13.74.0 255.255.255.0 outside
no snmp-server location
no snmp-server contact
snmp-server enable traps snmp authentication linkup linkdown coldstart warmstart
telnet timeout 5
ssh timeout 5
console timeout 0
dhcpd auto_config outside
threat-detection basic-threat
threat-detection statistics access-list
no threat-detection statistics tcp-intercept
webvpn
class-map inspection_default
match default-inspection-traffic
policy-map type inspect dns preset_dns_map
parameters
message-length maximum client auto
message-length maximum 512
policy-map global_policy
class inspection_default
inspect dns preset_dns_map
inspect ftp
inspect h323 h225
inspect h323 ras
inspect rsh
inspect rtsp
inspect esmtp
inspect sqlnet
inspect skinny
inspect sunrpc
inspect xdmcp
inspect sip
inspect netbios
inspect tftp
inspect ip-options
inspect icmp
service-policy global_policy global
prompt hostname context
no call-home reporting anonymous
Cryptochecksum:cde649be1382dd8249eca185657d9de7
: end

ASA 5505 backup interface

Hello,
I have setup ASA 5505 with 2 ISP, named outside (primary) and backup, the scenario is if outside down, then backup will take over, it works now.
But it is not working when the primary connection cannot reach the gateway with the interface still up.
Is it possible when the primary connection cannot reach the gateway then backup automatically take over?
Thanks before..
My configuration is:
ASA Version 8.2(1)
hostname cisco
domain-name default_domain
enable password ********* encrypted
passwd ********* encrypted
names
interface Vlan1
nameif inside
security-level 100
ip address 192.168.1.254 255.255.255.0
interface Vlan2
nameif outside
security-level 0
ip address 172.10.10.10 255.255.255.0
interface Vlan3
no forward interface Vlan2
nameif backup
security-level 0
ip address 172.20.10.10 255.255.255.0
interface Ethernet0/0
switchport access vlan 1
interface Ethernet0/1
switchport access vlan 2
interface Ethernet0/2
switchport access vlan 3
interface Ethernet0/3
interface Ethernet0/4
interface Ethernet0/5
interface Ethernet0/6
interface Ethernet0/7
ftp mode passive
dns server-group DefaultDNS
domain-name default domain
same-security-traffic permit intra-interface
pager lines 24
logging asdm informational
mtu inside 1500
mtu outside 1500
mtu backup 1500
icmp unreachable rate-limit 1 burst-size 1
no asdm history enable
arp timeout 14400
global (inside) 1 interface
global (outside) 1 interface
global (backup) 1 interface
nat (inside) 1 192.168.1.0 255.255.255.0
access-group inside_out in interface inside
access-group outside_in in interface outside
access-group backup_in in interface backup
route outside 0.0.0.0 0.0.0.0 172.10.10.1 1
route backup 0.0.0.0 0.0.0.0 172.20.10.1 254
timeout xlate 3:00:00
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
dynamic-access-policy-record DfltAccessPolicy
http server enable
http 192.168.1.0 255.255.255.0 inside
no snmp-server location
no snmp-server contact
snmp-server enable traps snmp authentication linkup linkdown coldstart
crypto ipsec security-association lifetime seconds 28800
crypto ipsec security-association lifetime kilobytes 4608000
telnet 192.168.1.0 255.255.255.0 inside
telnet timeout 5
ssh timeout 5
console timeout 0
dhcpd lease 1048575
dhcpd auto_config outside
dhcpd address 192.168.1.100-192.168.1.200 inside
dhcpd dns 8.8.8.8 8.8.4.4 interface inside
dhcpd enable inside
threat-detection basic-threat
threat-detection statistics access-list
no threat-detection statistics tcp-intercept
webvpn
class-map inspection_default
match default-inspection-traffic
policy-map global_policy
class inspection_default
inspect icmp
service-policy global_policy global
prompt hostname context
Cryptochecksum:24af050f332deab3e38eb578f8081d05
: end

Hi Amrin,
you can configure SLA monitoring on ASA and that woudl work fine for you:
http://www.cisco.com/en/US/products/hw/vpndevc/ps2030/products_configuration_example09186a00806e880b.shtml
Hope that helps.
Thanks,
Varun

Connect Inside to Outside in ASA 5505

Hi there,
I have a test ASA 5505 with the setting below:
How can I connect to the internet (Vlan 1 to VLan 11)
TestASA5505# show run
: Saved
ASA Version 8.2(4)
hostname TestASA5505
domain-name default.domain.invalid
enable password 8Ry2YjIyt7RRXU24 encrypted
passwd 2KFQnbNIdI.2KYOU encrypted
names
interface Ethernet0/0
switchport access vlan 11
interface Ethernet0/1
switchport access vlan 3
interface Ethernet0/2
interface Ethernet0/3
interface Ethernet0/4
interface Ethernet0/5
interface Ethernet0/6
interface Ethernet0/7
interface Vlan1
nameif inside
security-level 100
ip address 192.168.99.1 255.255.255.0
interface Vlan11
nameif outside
security-level 0
ip address 192.168.1.4 255.255.255.0
boot system disk0:/asa824-k8.bin
ftp mode passive
dns server-group DefaultDNS
domain-name default.domain.invalid
pager lines 24
logging enable
logging asdm informational
mtu inside 1500
mtu outside 1500
icmp unreachable rate-limit 1 burst-size 1
asdm image disk0:/asdm-647.bin
no asdm history enable
arp timeout 14400
route outside 0.0.0.0 255.255.255.255 192.168.1.4 1
timeout xlate 3:00:00
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
dynamic-access-policy-record DfltAccessPolicy
http server enable
http 192.168.99.0 255.255.255.0 inside
no snmp-server location
no snmp-server contact
snmp-server enable traps snmp authentication linkup linkdown coldstart
crypto ipsec security-association lifetime seconds 28800
crypto ipsec security-association lifetime kilobytes 4608000
telnet timeout 5
ssh timeout 5
console timeout 0
management-access inside
dhcpd address 192.168.99.3-192.168.99.30 inside
dhcpd enable inside
threat-detection basic-threat
threat-detection statistics access-list
no threat-detection statistics tcp-intercept
ssl encryption 3des-sha1 aes128-sha1 aes256-sha1 rc4-md5
webvpn
username admin password S1xyD1w.ZbjUT1yX encrypted privilege 15
policy-map type inspect dns preset_dns_map
parameters
message-length maximum 512
prompt hostname context
call-home
profile CiscoTAC-1
no active
destination address http https://tools.cisco.com/its/service/oddce/services/DDCEService
destination address email [email protected]
destination transport-method http
subscribe-to-alert-group diagnostic
subscribe-to-alert-group environment
subscribe-to-alert-group inventory periodic monthly
subscribe-to-alert-group configuration periodic monthly
subscribe-to-alert-group telemetry periodic daily
Cryptochecksum:096682b0996d6a1cad76597c01ffe5e2
: end
TestASA5505#
Thank you in Advance for your time

Hi,
What device is in front of the ASA?
Is there some ADSL modem doing NAT and providing Internet connection or something?
One obvious problem in the above configuration is the route
route outside 0.0.0.0 255.255.255.255 192.168.1.4 1
Its not actually even a default route and furthermore its pointing to the ASA itself
It should be something like this
route outside 0.0.0.0 0.0.0.0 192.168.1.x
Where the 192.168.1.x is the IP of the device providing the Internet connectivity to the ASA (Since ASA "outside" interface is using private IP address range)
If there ASA doesnt need to do any NAT then you could also add this
access-list INSIDE-NAT0 permit ip 192.168.99.0 255.255.255.0 any
nat (inside) 0 access-list INSIDE-NAT0
Also your DHCP configurations dont have any DNS servers defined.
dhcpd dns
- Jouni

Cisco ASA 5505 doesn't forware incoming connection to LAN

Hello everybody.
I just got a Cisco asa 5505 with the next OS and ASDM info
ASA 5505 OS 8.4(3) ASDM 6.47
I configured and enter all rules to allow incoming traffic to LAN but it's not working also, I have one host inside that is configured in a second IP and create the rule to allow traffic to it but it doesn't work too.
Problem 1
I have VNC running in port 5900 tcp and I want to connect from Internet using port 6001 and this has to forware the connection to the real VNC port. In the configuration I have a few host with the same configuration but I use different outside port to get it.
Problem 2.
I have a second IP with services: SMTP, HTTP, HTTPS and port 444 all TCP forwarding to a server in the LAN.
Facts:
SMTP.
Every time that I do telnet to the second IP looking for the SMTP port, the firewall doesn't let the incoming connection goes through and the LOGGING screen doesn't how that connection.
PORT 6001 (outside)
this port is configured to work with the IP in the outside internface and it was to send the incoming connection to a host inside to the real port 5900.
Can any one check my configuration if I'm missing anything? for sure I'm but I didn't find it. Bellow is the configuration, I masked the Public IPs just left the last number in the IP, also I left the LAN network to see better the configuration.
I will appreciate any help.
Thanks a lot..
CONFIGURATION.
: Saved
ASA Version 8.4(3)
hostname saturn1
domain-name mydominio.com
enable password SOMEPASS encrypted
passwd SOMEPASS encrypted
names
name 192.168.250.11 CAPITOLA-LAN
name 192.168.250.15 OBIi110-LAN
name 192.168.250.21 DRP1260-LAN
name 192.168.250.22 HPOJ8500-LAN
name 192.168.250.30 AP-W77-NG-LAN
name 192.168.250.97 AJ-DTOP-PC-LAN
name 192.168.250.96 SWEETHEART-PC-LAN
name 192.168.250.94 KIDS-PC-LAN
name XX.YY.ZZ.250 EXTERNALIP
name XX.YY.ZZ.251 EXTERNALIP2
name XX.YY.ZZ.1 GTWAY
dns-guard
interface Ethernet0/0
switchport access vlan 2
interface Ethernet0/1
interface Ethernet0/2
interface Ethernet0/3
interface Ethernet0/4
interface Ethernet0/5
interface Ethernet0/6
interface Ethernet0/7
interface Vlan1
nameif inside
security-level 100
ip address 192.168.250.2 255.255.255.0
interface Vlan2
nameif outside
security-level 0
ip address EXTERNALIP 255.255.255.0
boot system disk0:/asa843-k8.bin
ftp mode passive
dns server-group DefaultDNS
domain-name mydominio.com
object network CAPITOLA-LAN
host 192.168.250.11
object network EXTERNALIP
host XX.YY.ZZ.250
description Created during name migration
object network CAPITOLA-PUBLIC
host XX.YY.ZZ.251
object network capitola-int
host 192.168.250.11
object network capitola-int-vnc
host 192.168.250.11
object network aj-dtop-int-vnc
host 192.168.250.97
object network sweetheart-int-vnc
host 192.168.250.96
object network kids-int-vnc
host 192.168.250.94
object network VPNNetwork
subnet 10.10.20.0 255.255.255.0
object network InsideNetwork
subnet 192.168.250.0 255.255.255.0
object network obj_any
subnet 0.0.0.0 0.0.0.0
object network capitola-int-smtp
host 192.168.250.11
object-group service capitola-int-smtp-service tcp
port-object eq smtp
object-group service capitola-int-services tcp
port-object eq smtp
port-object eq https
port-object eq www
port-object eq 444
object-group service capitola-int-vnc-service tcp
port-object eq 6001
object-group service aj-dtop-int-vnc-service tcp
port-object eq 6002
object-group service sweetheart-int-vnc-service tcp
port-object eq 6003
object-group service kids-int-vnc-service tcp
port-object eq 6004
access-list incoming extended permit icmp any any
access-list incoming extended permit tcp any object capitola-int object-group capitola-int-services
access-list incoming extended permit tcp any object capitola-int-vnc object-group capitola-int-vnc-service
access-list incoming extended permit tcp any object aj-dtop-int-vnc object-group aj-dtop-int-vnc-service
access-list incoming extended permit tcp any object sweetheart-int-vnc object-group sweetheart-int-vnc-service
access-list incoming extended permit tcp any object kids-int-vnc object-group kids-int-vnc-service
access-list incoming extended permit tcp any object capitola-int-smtp object-group capitola-int-smtp-service
access-list split-tunnel standard permit 192.168.250.0 255.255.255.0
access-list inside_nat0_outbound extended permit ip any object VPNNetwork
pager lines 24
logging enable
logging asdm informational
mtu inside 1500
mtu outside 1500
ip local pool vpnpool 10.10.20.1-10.10.20.50 mask 255.255.255.0
icmp unreachable rate-limit 1 burst-size 1
asdm image disk0:/asdm-647.bin
no asdm history enable
arp timeout 14400
nat (inside,any) source static any any destination static VPNNetwork VPNNetwork no-proxy-arp
object network capitola-int
nat (any,any) static XX.YY.ZZ.251
object network capitola-int-vnc
nat (inside,outside) static interface service tcp 5900 6001
object network aj-dtop-int-vnc
nat (inside,outside) static interface service tcp 5900 6002
object network sweetheart-int-vnc
nat (inside,outside) static interface service tcp 5900 6003
object network kids-int-vnc
nat (inside,outside) static interface service tcp 5900 6004
object network obj_any
nat (inside,outside) dynamic interface
object network capitola-int-smtp
nat (any,outside) static interface service tcp smtp smtp
access-group incoming in interface outside
route outside 0.0.0.0 0.0.0.0 GTWAY 1
timeout xlate 3:00:00
timeout pat-xlate 0:00:30
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
timeout floating-conn 0:00:00
dynamic-access-policy-record DfltAccessPolicy
user-identity default-domain LOCAL
aaa authentication ssh console LOCAL
http server enable
http server idle-timeout 2
http server session-timeout 1
http 192.168.1.0 255.255.255.0 inside
http CAPITOLA-LAN 255.255.255.255 inside
http AJ-DTOP-PC-LAN 255.255.255.255 inside
no snmp-server location
no snmp-server contact
snmp-server enable traps snmp authentication linkup linkdown coldstart
telnet timeout 5
ssh CAPITOLA-LAN 255.255.255.255 inside
ssh AJ-DTOP-PC-LAN 255.255.255.255 inside
ssh timeout 15
console timeout 0
vpn-addr-assign local reuse-delay 2
dhcpd auto_config outside
threat-detection basic-threat
threat-detection statistics access-list
no threat-detection statistics tcp-intercept
webvpn
username admin password SOMEPASS encrypted privilege 15
class-map inspection_default
match default-inspection-traffic
policy-map type inspect dns preset_dns_map
parameters
message-length maximum 512
policy-map global_policy
class inspection_default
inspect dns preset_dns_map
inspect ftp
inspect h323 h225
inspect h323 ras
inspect rsh
inspect rtsp
inspect sqlnet
inspect skinny
inspect sunrpc
inspect xdmcp
inspect sip
inspect netbios
inspect tftp
inspect pptp
inspect ip-options
service-policy global_policy global
prompt hostname context
no call-home reporting anonymous
call-home
profile CiscoTAC-1
no active
destination address http https://tools.cisco.com/its/service/oddce/services/DDCEService
destination address email [email protected]
destination transport-method http
subscribe-to-alert-group diagnostic
subscribe-to-alert-group environment
subscribe-to-alert-group inventory periodic monthly
subscribe-to-alert-group configuration periodic monthly
subscribe-to-alert-group telemetry periodic daily
Cryptochecksum:036b82d3eb5cffc1c65a3b381246d043
: end
asdm image disk0:/asdm-647.bin
no asdm history enable

Jose, your fix to problem 1 allows all access from the outside, assuming you applied the extended list to the outside interface. Try to be more restrictive than an '...ip any any' rule for outside_in connections. For instance, this is what I have for incoming VOIP (access list and nat rules):
access list rule:
access-list outside_access_in extended permit udp any object server range 9000 9049 log errors
nat rule:
nat (inside,outside) source static server interface service voip-range voip-range
- 'server' is a network object *
- 'voip-range' is a service group range
I'd assume you can do something similar here in combination with my earlier comment:
access-list incoming extended permit tcp any any eq 5900
Can you explain your forwarding methodology a little more? I'm by no means an expert on forwarding, but the way I read what you're trying to do is that you have an inbound VNC request coming in on 5900 and you want the firewall to figure out which host the request should go to. Or is it vice-versa, the inbound VNC request can be on port 6001-6004 ?

Need HELPS! ASA 5505 8.4 Cisco VPN Client cannot ping any internal host

Hi:
Need your great help for my new ASA 5505 (8.4)
I just set a new ASA 5505 with 8.4. However, I cannot ping any host after VPN in with Cisco VPN client. Please see below posted configuration file, thanks for any suggestion.
ASA Version 8.4(3)
names
interface Ethernet0/0
switchport access vlan 2
interface Ethernet0/1
switchport access vlan 2
interface Ethernet0/2
interface Ethernet0/3
interface Ethernet0/4
interface Ethernet0/5
interface Ethernet0/6
interface Ethernet0/7
interface Vlan1
nameif inside
security-level 100
ip address 172.29.8.254 255.255.255.0
interface Vlan2
nameif outside
security-level 0
ip address 177.164.222.140 255.255.255.248
ftp mode passive
clock timezone GMT 0
dns server-group DefaultDNS
domain-name ABCtech.com
same-security-traffic permit inter-interface
object network obj_any
subnet 172.29.8.0 255.255.255.0
object service RDP
service tcp source eq 3389
object network orange
host 172.29.8.151
object network WAN_173_164_222_138
host 177.164.222.138
object service SMTP
service tcp source eq smtp
object service PPTP
service tcp source eq pptp
object service JT_WWW
service tcp source eq www
object service JT_HTTPS
service tcp source eq https
object network obj_lex
subnet 172.29.88.0 255.255.255.0
description Lexington office network
object network obj_HQ
subnet 172.29.8.0 255.255.255.0
object network guava
host 172.29.8.3
object service L2TP
service udp source eq 1701
access-list VPN_Tunnel_User standard permit 172.29.8.0 255.255.255.0
access-list VPN_Tunnel_User standard permit 172.29.88.0 255.255.255.0
access-list inside_access_in extended permit icmp any any
access-list inside_access_in extended deny tcp any any eq 135
access-list inside_access_in extended deny tcp any eq 135 any
access-list inside_access_in extended deny udp any eq 135 any
access-list inside_access_in extended deny udp any any eq 135
access-list inside_access_in extended deny tcp any any eq 1591
access-list inside_access_in extended deny tcp any eq 1591 any
access-list inside_access_in extended deny udp any eq 1591 any
access-list inside_access_in extended deny udp any any eq 1591
access-list inside_access_in extended deny tcp any any eq 1214
access-list inside_access_in extended deny tcp any eq 1214 any
access-list inside_access_in extended deny udp any any eq 1214
access-list inside_access_in extended deny udp any eq 1214 any
access-list inside_access_in extended permit ip any any
access-list inside_access_in extended permit tcp any any eq www
access-list inside_access_in extended permit tcp any eq www any
access-list outside_access_in extended permit icmp any any
access-list outside_access_in extended permit tcp any host 177.164.222.138 eq 33
89
access-list outside_access_in extended permit tcp any host 177.164.222.138 eq sm
tp
access-list outside_access_in extended permit tcp any host 177.164.222.138 eq pp
tp
access-list outside_access_in extended permit tcp any host 177.164.222.138 eq ww
w
access-list outside_access_in extended permit tcp any host 177.164.222.138 eq ht
tps
access-list outside_access_in extended permit gre any host 177.164.222.138
access-list outside_access_in extended permit udp any host 177.164.222.138 eq 17
01
access-list outside_access_in extended permit ip any any
access-list inside_access_out extended permit icmp any any
access-list inside_access_out extended permit ip any any
access-list outside_cryptomap extended permit ip 172.29.8.0 255.255.255.0 172.29
.88.0 255.255.255.0
access-list inside_in extended permit icmp any any
access-list inside_in extended permit ip any any
access-list inside_in extended permit udp any any eq isakmp
access-list inside_in extended permit udp any eq isakmp any
access-list inside_in extended permit udp any any
access-list inside_in extended permit tcp any any
pager lines 24
logging enable
logging asdm informational
mtu inside 1500
mtu outside 1500
ip local pool ABC_HQVPN_DHCP 172.29.8.210-172.29.8.230 mask 255.255.255.0
icmp unreachable rate-limit 1 burst-size 1
asdm history enable
arp timeout 14400
nat (inside,outside) source static orange interface service RDP RDP
nat (inside,outside) source static obj_HQ obj_HQ destination static obj_lex obj_
lex route-lookup
nat (inside,outside) source static guava WAN_173_164_222_138 service JT_WWW JT_W
WW
nat (inside,outside) source static guava WAN_173_164_222_138 service JT_HTTPS JT
_HTTPS
nat (inside,outside) source static guava WAN_173_164_222_138 service RDP RDP
nat (inside,outside) source static guava WAN_173_164_222_138 service SMTP SMTP
nat (inside,outside) source static guava WAN_173_164_222_138 service PPTP PPTP
nat (inside,outside) source static guava WAN_173_164_222_138 service L2TP L2TP
object network obj_any
nat (inside,outside) dynamic interface
access-group inside_in in interface inside
access-group outside_access_in in interface outside
route outside 0.0.0.0 0.0.0.0 177.164.222.142 1
route inside 172.29.168.0 255.255.255.0 172.29.8.253 1
timeout xlate 3:00:00
timeout pat-xlate 0:00:30
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
timeout floating-conn 0:00:00
dynamic-access-policy-record DfltAccessPolicy
aaa-server Guava protocol nt
aaa-server Guava (inside) host 172.29.8.3
timeout 15
nt-auth-domain-controller guava
user-identity default-domain LOCAL
http server enable
http 172.29.8.0 255.255.255.0 inside
no snmp-server location
no snmp-server contact
snmp-server enable traps snmp authentication linkup linkdown coldstart warmstart
crypto ipsec ikev1 transform-set ESP-AES-128-SHA esp-aes esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-AES-128-MD5 esp-aes esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-AES-256-SHA esp-aes-256 esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-3DES-SHA esp-3des esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-3DES-MD5 esp-3des esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-DES-SHA esp-des esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-DES-MD5 esp-des esp-md5-hmac
crypto ipsec ikev1 transform-set Remote_VPN_Set esp-3des esp-md5-hmac
crypto ipsec ikev1 transform-set Remote_vpn_set esp-3des esp-md5-hmac
crypto ipsec ikev2 ipsec-proposal AES256
protocol esp encryption aes-256
protocol esp integrity sha-1 md5
crypto ipsec ikev2 ipsec-proposal AES192
protocol esp encryption aes-192
protocol esp integrity sha-1 md5
crypto ipsec ikev2 ipsec-proposal AES
protocol esp encryption aes
protocol esp integrity sha-1 md5
crypto ipsec ikev2 ipsec-proposal 3DES
protocol esp encryption 3des
protocol esp integrity sha-1 md5
crypto ipsec ikev2 ipsec-proposal DES
protocol esp encryption des
protocol esp integrity sha-1 md5
crypto dynamic-map outside_dyn_map 20 set ikev1 transform-set Remote_VPN_Set
crypto dynamic-map outside_dyn_map 20 set reverse-route
crypto map outside_map 1 match address outside_cryptomap
crypto map outside_map 1 set peer 173.190.123.138
crypto map outside_map 1 set ikev1 transform-set ESP-AES-128-SHA ESP-AES-128-MD5
ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA ES
P-3DES-MD5 ESP-DES-SHA ESP-DES-MD5
crypto map outside_map 1 set ikev2 ipsec-proposal AES256 AES192 AES 3DES DES
crypto map outside_map 65535 ipsec-isakmp dynamic outside_dyn_map
crypto map outside_map interface outside
crypto ikev2 policy 1
encryption aes-256
integrity sha
group 5 2
prf sha
lifetime seconds 86400
crypto ikev2 policy 10
encryption aes-192
integrity sha
group 5 2
prf sha
lifetime seconds 86400
crypto ikev2 policy 20
encryption aes
integrity sha
group 5 2
prf sha
lifetime seconds 86400
crypto ikev2 policy 30
encryption 3des
integrity sha
group 5 2
prf sha
lifetime seconds 86400
crypto ikev2 policy 40
encryption des
integrity sha
group 5 2
prf sha
lifetime seconds 86400
crypto ikev2 enable outside
crypto ikev1 enable outside
crypto ikev1 policy 1
authentication pre-share
encryption 3des
hash sha
group 2
lifetime 43200
crypto ikev1 policy 10
authentication crack
encryption aes-256
hash sha
group 2
lifetime 86400
crypto ikev1 policy 20
authentication rsa-sig
encryption aes-256
hash sha
group 2
lifetime 86400
crypto ikev1 policy 30
authentication pre-share
encryption aes-256
hash sha
group 2
lifetime 86400
crypto ikev1 policy 40
authentication crack
encryption aes-192
hash sha
group 2
lifetime 86400
crypto ikev1 policy 50
authentication rsa-sig
encryption aes-192
hash sha
group 2
lifetime 86400
crypto ikev1 policy 60
authentication pre-share
encryption aes-192
hash sha
group 2
lifetime 86400
crypto ikev1 policy 70
authentication crack
encryption aes
hash sha
group 2
lifetime 86400
crypto ikev1 policy 80
authentication rsa-sig
encryption aes
hash sha
group 2
lifetime 86400
crypto ikev1 policy 90
authentication pre-share
encryption aes
hash sha
group 2
lifetime 86400
crypto ikev1 policy 100
authentication crack
encryption 3des
hash sha
group 2
lifetime 86400
crypto ikev1 policy 110
authentication rsa-sig
encryption 3des
hash sha
group 2
lifetime 86400
crypto ikev1 policy 120
authentication pre-share
encryption 3des
hash sha
group 2
lifetime 86400
crypto ikev1 policy 130
authentication crack
encryption des
hash sha
group 2
lifetime 86400
crypto ikev1 policy 140
authentication rsa-sig
encryption des
hash sha
group 2
lifetime 86400
crypto ikev1 policy 150
authentication pre-share
encryption des
hash sha
group 2
lifetime 86400
telnet 192.168.1.0 255.255.255.0 inside
telnet 172.29.8.0 255.255.255.0 inside
telnet timeout 5
ssh timeout 5
console timeout 0
dhcpd auto_config outside vpnclient-wins-override
dhcprelay server 172.29.8.3 inside
threat-detection basic-threat
threat-detection statistics access-list
no threat-detection statistics tcp-intercept
webvpn
enable outside
group-policy ABCtech_VPN internal
group-policy ABCtech_VPN attributes
dns-server value 172.29.8.3
vpn-tunnel-protocol ikev1
split-tunnel-policy tunnelspecified
split-tunnel-network-list value VPN_Tunnel_User
default-domain value ABCtech.local
group-policy GroupPolicy_10.8.8.1 internal
group-policy GroupPolicy_10.8.8.1 attributes
vpn-tunnel-protocol ikev1 ikev2
username who password eicyrfJBrqOaxQvS encrypted
tunnel-group 10.8.8.1 type ipsec-l2l
tunnel-group 10.8.8.1 general-attributes
default-group-policy GroupPolicy_10.8.8.1
tunnel-group 10.8.8.1 ipsec-attributes
ikev1 pre-shared-key *****
ikev2 remote-authentication pre-shared-key *****
ikev2 remote-authentication certificate
ikev2 local-authentication pre-shared-key *****
tunnel-group ABCtech type remote-access
tunnel-group ABCtech general-attributes
address-pool ABC_HQVPN_DHCP
authentication-server-group Guava
default-group-policy ABCtech_VPN
tunnel-group ABCtech ipsec-attributes
ikev1 pre-shared-key *****
tunnel-group 173.190.123.138 type ipsec-l2l
tunnel-group 173.190.123.138 general-attributes
default-group-policy GroupPolicy_10.8.8.1
tunnel-group 173.190.123.138 ipsec-attributes
ikev1 pre-shared-key *****
ikev2 remote-authentication pre-shared-key *****
ikev2 remote-authentication certificate
ikev2 local-authentication pre-shared-key *****
class-map inspection_default
match default-inspection-traffic
policy-map global_policy
class inspection_default
inspect pptp
inspect ftp
inspect netbios
smtp-server 172.29.8.3
prompt hostname context
no call-home reporting anonymous
Cryptochecksum:6a26676668b742900360f924b4bc80de
: end

Hello Wayne,
Can you use a different subnet range than the internal interface, this could cause you a LOT of issues and hours on troubleshooting, so use a dedicated different Ip address range...
I can see that the local Pool range is included into the inside interface Ip address subnet range, change that and the related config ( NAT,etc, ) and let us know what happens,
Regards,
Julio
Security Trainer

Catalyst 5505 With Catalyst 2948G

Similar Messages

Maybe you are looking for