CellEditor does not end edit mode when finished editing

I have a custom cell editor and it does not return from edit mode once the cell has been edited. Can anyone help ?

Post your table cell editor code

Similar Messages

All-in-one 6830 printer Does not enter sleep mode when connected to a phone line

HP staff help. HP all-in-one printer 6830 does not enter sleep mode when conntected to a phone line via 1-Line jack. The Firmware is PNP1CN1521AR. On August 1, 2015, I purchased an HP all-in-one 6830 printer and upgraded to firmware PNP1CN1521AR.When a phone line is connected to 1-Line jack of 6830, the printer will no longer enter sleep mode and the display remains on indefinitly.Removing the phone connection either from the wall outlet or from the printer causes the sleep mode to work correctly again where the control panel display turns off after 5 minutes (or optionally after 10 or 15 minutes).This problem was previously reported by a user and has not been resolved, see:http://h30434.www3.hp.com/t5/Other-Printing-Questions/Sleep-mode-of-Officejet-Pro-6830/td-p/4772182 The user did not receive a resolution to this problem according to the thread.
There seems to be a 6830 printer firmware or hardware problem causing this. HP should be able to confirm this problem on 6830 easily.
Please advise ASAP.
Thanks

It's a regular analog phone line. I've tested it with other phone lines. No difference. I have another all-in-one printer which works fine (goes to sleep mode) when plugged into the same phone line.
The 6830 works ok in other aspects. The only problem is the sleep mode. Any 6830 with the firmware I mentioned should replicate the same result, regardless of anything else. The previous firmware to PNP1CN1521AR also created this problem according to the original report of this problem by another user.
I'm sure there's a bug in the firmware. A subroutine in the firmware monitoring the incoming fax ringing, mistakenly, sees the voltage across the phone jack pins as an event and wakes up the printer instantly even though there's no ringing. As the previous user also suspected, there seems to be an error in the phone line voltage threshold used by the firmware. The present firmware always sees a ringing at the phone line which causes it to never stay in sleep mode.

Concurrent request does not end into error when expected

Hi All,
RDBMS : 9.2.0.8.0
Oracle Applicaties : 11.5.10.2
Consider the following testcase:
SQL>
SQL> create or replace procedure p1
2 as
3 begin
4 raise no_data_found;
5 end;
6 /
Procedure created
SQL> create or replace procedure p2
2 ( errbuff in out varchar2
3 , retcode in out varchar2
4 )
5 as
6 begin
7 p1;
8 end;
9 /
Procedure created
SQL> declare
2 errbuff varchar2(4000);
3 retcode varchar2(4000);
4
5 begin
6 p2(errbuff,retcode);
7 end;
8 /
declare
errbuff varchar2(4000);
retcode varchar2(4000);
begin
p2(errbuff,retcode);
end;
ORA-01403: no data found
ORA-06512: at "APPS.P1", line 4
ORA-06512: at "APPS.P2", line 7
ORA-06512: at line 6
SQL>
The exception is returned as expected.
However, when I create a concurrent program for procedure p2 and I run it, it finishes normally with no errors. I want it to go into error?
I would expect the concurrent manager to notice the exception and therefore exit with status error. Am i missing something?
Using a when others exception in p2 helps, but actually I consider that 'dirty programming'. Is it really necessary?
Thanks in Advance,
Martin
Edited by: Martin van Donselaar on 9-dec-2008 10:10

Hi Martin,
you have to know that the retcode can be 0,1 or 2. Return 0 to indicate Normal, return 1 to indicate Waring (Yellow) or return 2 to indicate error (Red). The errbuf can be any text, that will be written into the log always.
Hope this helps
Volker

Firefox sometimes does not end

14.7.2014
Firefox 30.0 (German version) under Win 8.1
Hello,
Sometimes Firefox does not end properly. When Firefox is re-started I get a message saying Firefox
is still running although about 10 minutes has passed between end and the re-start.
Only by killing Firefox in the Task Manager can cure this problem. I use firefox a lot and this occurs about 5 times a day.

Firefox Keep running in background, that's why your getting this error
*http://kb.mozillazine.org/Firefox.exe_always_open
Sometimes a problem with Firefox may be a result of malware installed on your computer, that you may not be aware of.
You can try these free programs to scan for malware, which work with your existing antivirus software:
* [http://www.microsoft.com/security/scanner/default.aspx Microsoft Safety Scanner]
* [http://www.malwarebytes.org/products/malwarebytes_free/ MalwareBytes' Anti-Malware]
* [http://support.kaspersky.com/viruses/disinfection/5350 Anti-Rootkit Utility - TDSSKiller]
* [http://general-changelog-team.fr/en/downloads/viewdownload/20-outils-de-xplode/2-adwcleaner AdwCleaner] (for more info, see this [http://www.bleepingcomputer.com/download/adwcleaner/ alternate AdwCleaner download page])
* [http://www.surfright.nl/en/hitmanpro/ Hitman Pro]
* [http://www.eset.com/us/online-scanner/ ESET Online Scanner]
[http://windows.microsoft.com/MSE Microsoft Security Essentials] is a good permanent antivirus for Windows 7/Vista/XP if you don't already have one.
Further information can be found in the [[Troubleshoot Firefox issues caused by malware]] article.
Did this fix your problems? Please report back to us!

Process does not end when binding a object to registry

I am writing a Unit Test case in which i need to create a datasource and bind it to RMI registry so that the methods i need to test can get a database connection . The problem is that after the test cases have finished running the process does not end and i have to shut it down manually . When i do not bind the datasource , the process ends put with errors because the methods do not get a connection. Even unbinding it after running the test cases does not help.
Edited by: gurpreetbhalla on Jun 25, 2009 11:56 AM

public void testIntraDayForClient() throws Exception
          ConstantConfig.JNDI_FACTORY = "com.sun.jndi.rmi.registry.RegistryContextFactory";
          Hashtable env = new Hashtable();
          env.put(Context.INITIAL_CONTEXT_FACTORY,"com.sun.jndi.rmi.registry.RegistryContextFactory");
          env.put(Context.PROVIDER_URL, "rmi:");
InitialContext ic = new InitialContext(env);
// Construct DataSource
SQLServerConnectionPoolDataSource ds = new SQLServerConnectionPoolDataSource();
ds.setURL("jdbc:sqlserver://10.200.41.201:1433;databaseName=TradeportTC");
ds.setUser("sa");
ds.setPassword("superuser");
DataSource d = ds;
     ic.unbind("TCDB_JNDI");
ic.bind("TCDB_JNDI", ds);
          HttpServletRequest req = new MockHttpRequest();
          HttpServletResponse resp = EasyMock.createMock(HttpServletResponse.class);
          ActionContext context = EasyMock.createMock(ActionContext.class);
          HttpSession session = EasyMock.createMock(HttpSession.class);
          EasyMock.expect(session.getAttribute("ZephyrUserName")).andReturn("sclient90");
          EasyMock.expect(session.getAttribute("ZephyrDomainId")).andReturn("8a48a9cb1860e2a4011860e2c64d003a");
          EasyMock.expect(session.getAttribute("isTrader")).andReturn(false);
          EasyMock.expect(session.getAttribute("accountsDataDB")).andReturn(null);
          EasyMock.expect(context.getSession()).andReturn(session).times(12);
          session.setAttribute("vawTrades", null);
          session.setAttribute("noOfDays", null);
          session.setAttribute("accountNo", null);
          session.setAttribute("exchange", null);
          session.setAttribute("symbolName", null);
          session.setAttribute("trCode", null);
          session.setAttribute("status", null);
          session.setAttribute("accountsDataDB", null);
          EasyMock.replay(session);
          EasyMock.replay(context);
          MyOrdersAction action = new MyOrdersAction();
          action.execute(req, resp, context);
This is the unit test case which does not exit , if i skip this binding ic.bind("TCDB_JNDI", ds);
then it exits normally with a failure,

My ipod touch has a permanent image of the end of a USB cable with an arrow pointing to an icon of ITunes. I can't reset, and ipod does not appear on itunes when I plug it into the computer. This happened after I agreed to a failed software update.

My ipod touch has a permanent image of the end of a USB cable with an arrow pointing to an icon of ITunes. I can't reset using the two button method, and ipod does not appear on itunes when I plug it into the computer - and nothing else happens either. This happened after I agreed to a software update which failed. How can I get it going again?

Try:
- iOS: Not responding or does not turn on
- Also try DFU mode after try recovery mode
How to put iPod touch / iPhone into DFU mode « Karthik's scribblings
- If not successful and you can't fully turn the iOS device fully off, let the battery fully drain. After charging for an least an hour try the above again.
- If still not successful that usually indicates a hardware problem and an appointment at the Genius Bar of an Apple store is in order.
Apple Retail Store - Genius Bar

HT201317 My photostream in windows 7 PC does not shows any pic. when i click on slide show it start showing me slide shows of pic but when i try to copy files i cant do as no photo is viewd in list mode. This problem has arised since IOS is updated.

My photostream in windows 7 PC does not shows any pic. when i click on slide show it start showing me slide shows of pic but when i try to copy files i cant do as no photo is viewd in list mode. This problem has arised since IOS is updated.I reinstalled my icloud and checked if icloud sharing is ON. I can see pic in my photo stream in PC only in slide show mode. While in list mode it shows pics before i actually click on photostream folder. My phone memory is out becose of bunch of photoes. How do i copy my photostream photoes.

Hi all. I can’t tell you how to solve your iCloud 3.x issues. Heck, I don’t think they’re even solvable.
But if you had a previous version of iCloud that was working correctly then I can definitely tell you how to solve the “iCloud Photo Stream is not syncing correctly to my Windows 7 PC” problem. …without even a re-boot.
Log out of iCloud 3.0 and uninstall it.
Open My Computer and then open your C:\ drive. Go to Tools/Folder Options and click on the View tab. Select the “Show hidden…” radio button and click on OK.
Open the Users folder.
Open your user folder
Open ProgramData (previously hidden folder)
Open the Apple folder – not the Apple Computer folder.
Open the Installer Cache folder
In Details view sort on Name
Open the folder for the newest entry for iCloud Control Panel 2.x – probably 2.1.2.8 dated 4/25/2013
Right click on iCloud64.msi and select Install.
When finished, the synching between iCloud and your PC will be back to working perfectly as before the 3.0 fiasco. The pictures will be synched to the same Photostream folder as before the “upgrade”. Now all you need to do is wait until Apple/Microsoft get this thing fixed and working before you try the 3.x upgrade again.
I think the iCloud 3.0 software was written by the same folks who wrote healthcare.gov with the main difference being that healthcare.gov might eventually be made to work.
For those of you who hate to go backwards, think of it as attacking to the rear. Which would you rather have, the frustration of no synching or everything working on an older version?
Good luck…

MacBook Pro does not go to sleep when power cord is connected

Hi Experts,
I have recently discovered that my MacBook Pro (2009) with OSX Lion does not go to sleep when the power cord is connected. It does not matter if I close the lid or select sleep from the Apple menu. All that happens is that the screen is powered off, the SIL is solid and I can hear the HDD/fan. I have not changed any of my power settings recently and it has not been a problem previously. If I disconnect the power cord the MB goes to sleep as supposed to (the SIL led starts flashing).
Doing some research I have found other users with somewhat the same issues when VMWare Fusion is installed. I have done some further testing and it seems that if I disable the virtual machine's Network Adapter and quit VMWare Fusion the MB goes into sleeping mode when the lid is closed even with the power cord connected. Enabling the Network Adapter again prevents the MB to go into sleeping mode when the power cord is connected. This even applies when the VMWare application is shutted down.
My guess is that the Network Adapter somehow prevents the MB to go into sleeping mode. The workaround is of course toggling the Network Adapter on and off but the virtual machine has to be running in order to do so. Not being that familiar with network settings on a Mac is there any other way to get around the problem?
Thanks in advance :-)

To anyone,
I have turned internet sharing off but the Ethernet box remains checked. If I uncheck the Ethernet box, the Internet Sharing bubble turns red, however when I close System Preferences and re-open, the box is automatically checked although Internet Sharing is off. Because of this my Macbook Pro will not sleep properly.
All other sharing items are turned off. Only Internet Sharing continues to automatically show Ethernet as active from a Wi-Fi connection.
Any advice?

Execution does not end even after all records updated..

Hi,
I have plsql code like :
declare
begin
for x in ( select .......) loop -- about 4000 times
for y in ( select ............) loop -- about 50 times
end loop;
-- some code goes here to manipulate clob data
-- like creating free temp clobs - use - then free them
-- Update statement that update some table using clob values.
insert into tablex values(sysdate);
commit;
end loop;
end;
Here I can monitor from other window howmany records are inserted into tablex and howmany updated in update statement by...
select count(1) from tablex;
After 50 mins i can see that all records are updated but...
plsql code does not end its execution it continues even after all records are updated..untill i have to kill the session or let be run for long time.. :(
I can not understand why this it is not ending execution..
What could be the problem ...

Hi,
Here it is.....
declare
v_text_data TableA.text_data%type;
v_clob clob;
type dummyclob_t is table of clob index by binary_integer;
dummyclob dummyclob_t;
v_str varchar2(255) := 'ddfsajfdkeiueimnrmrrttrtr;trtkltwjkltjiu4i5u43iou43i5u4io54urnmlqwmreqwnrewmnrewmreqwnm,rewqnrewqrewqljlkj';
begin
select data bulk collect into dummyclob from sfdl_clob; -- five rows containing clob data upto 1MB
for x in (select object_id
from TableA
where object_type = 'STDTEXT' ) loop
dbms_lob.createtemporary(v_text_data,TRUE);
for y in (select '<IMG "MFI_7579(@CONTROL=' || ref_id || ',REF_ID=' || ref_id || ').@UDV">' temp_data
from TableB
where object_id = x.object_id) loop
v_text_data := v_text_data ||
case
when trunc(dbms_random.value(0,7)) = 0
then chr(10)
else v_str
end ||
y.temp_data;
end loop;
select text_data into v_clob from TableA where object_id = x.object_id for update;
if v_text_data is not null then
dbms_lob.append(v_clob,v_text_data);
end if;
dbms_lob.append(v_clob,dummyclob(trunc(dbms_random.value(1, 6))));
dbms_lob.freetemporary(v_text_data);
insert into xyz values (sysdate);
commit;
end loop;
end;
Thanks for your time..:)
Rushang.

Ever since my last update I have been unable to add songs from my i tunes library onto my i phone. The "add to" button does not appear for me when I connect my i phone. Can anyone shed some light on this for me?

Ever since my last update I have been unable to add songs from my i tunes library onto my i phone. The "add to" button does not appear for me when I connect my i phone. Can anyone shed some light on this for me?

Thanks for that 'sberman' - because my iPhone is backed-up to my work computer (only at this stage) I have had to call our IT Department in Adleaide. (4 times this morning). The last guy managed to get the phone into 'DFU Mode' - no more recovery mode screen - (kind of 'asleep' perhaps) from my understanding of same. I am awaiting a call again from IT so they can get my computer to actually recognise my iPhone on the C Drive. This also happened to one of my colleagues in Newman (WA). She got so frustrated with the whole process that she bought another phone the next time she was in 'civilisation.' She hasn't had any problems since. (Cross fingers).
Thanks again, Sandra2474.

Excel process does not end properly

Hello All.
I am using excel in my program writing data into it an excel workbook and then later on reading data from it. I have written down the code of closing excel worlkbook and shutting down excel application hence releasing the handles for it. But when i do that i.e. when the code containing excel workbook closing and excel application shutting down executes, excel workbook is closed but excel process does not end properly and can be seen in the task manager. And when i repeatedly open the excel file through my front end interface and close the file, another excel process is added in the task manager which does not end and so on. What can be the problem and solution. Thanks in advance.
Best Regards.
Moshi.

Interfacing to Excel via ActiveX may be tricky, ending in situations like the one you are facing now.
The basic principle is that every single handle opened to an Excel object (workbook, worksheet, range, variant and so on) must be closed properly for the entire process to terminate gracefully. If a reference remains unhandled at program end you will find an instance of Excel remaining in the task list and you may suffer erratic behaviour in subsequent accesses to the product.
You must double check all references and add approporiate dispose/close commands for every one of them.
Proud to use LW/CVI from 3.1 on.
My contributions to the Developer Zone Community
If I have helped you, why not giving me a kudos?

IDocumentQuery.Execute() method throws user does not have edit permissions exception

I'm trying to query a document folder for all of its containing documents. Its a basic query like this:
IPortletContext PortletContext = PortletContextFactory.CreatePortletContext(Request,Response);IRemoteSession PTSession;PTSession = PortletContext.GetRemotePortalSession();IDocumentManager documentManager = PTSession.GetDocumentManager();
IDocumentQuery documentQuery = documentManager.CreateQuery(FolderID); documentQuery.SetSortProperty(ObjectProperty.Name);IObjectQuery queryResults = documentQuery.Execute();
When I'm logged into the portal as an administrator, everything works fine. However if I'm logged in as a "regular" user, I get this exception when calling the Execute() method:
Plumtree.Remote.PRC.PortalException: Exception of type Plumtree.Remote.PRC.PortalException was thrown. ---> System.Web.Services.Protocols.SoapException: Server was unable to process request. --> Access denied: Current user does not have edit permission
I'm sending the Login Token to the portlet. Now I've tried giving the user Edit rights on the document folder as well as Edit the Knowledge Directory rights in the Activity Manager, but neither gets rid of the exception. I'm not sure what other "Edit" permissions to check. I don't even see why the user would need "Edit" permission to anything in the first place since the Execute() method simply returns an IObjectQuery that doesn't have any ability to make changes to any objects. I know that I could use the SearchFactory interface, but I wanted the results to be real time. Any help would be much appreciated. Thanks!
Jimmy

The problem here is that the query is created with default settings to show unapproved documents -- only users with edit access can see unapproved documents. Add the bold line to your code and it will work.
IDocumentManager docManager = prcSession.GetDocumentManager();IDocumentQuery docQuery = docManager.CreateQuery(iFolderID);docQuery.SetShowUnapproved(false);IObjectQuery queryResults = docQuery.Execute()

My Creative Cloud does not work anymore. When I try to reinstall it I receive the message "AAM cannot initialise". I have tried all the instructions but it still does not work. Robert

My Creative Cloud does not work anymore. When I try to reinstall it I receive the message "AAM cannot initialise". I have tried all the instructions but it still does not work. Robert

Try perform below steps.
Open task manager by pressing Ctrl + Shift + Esc keys. Click on more details if the option available.
Then end all Adobe related processes, including Creative Cloud and Coresync ( if running )
Then hold windows key on your keyboard and Press R key.
It will open Run window
In Run window, type Appdata and click on Ok
Open Local > Adobe folders
Delete AAMUpdater and OOBE folders
Then navigate to C:\Program Files (x86)\Common Files\Adobe
Delete Adobe Application Manager and OOBE folders
Go back to Program Files (x86) and Open Adobe folder
Try deleting Adobe Creative Cloud folder, if it is not allowing rename it to Adobe Creative Cloudold
Download and install Creative Cloud App from below link
https://creative.adobe.com/products/download/creative-cloud
Then check

PekWM Does not end XSession

When using the "exit" from pekwm's menu, it does not end my Xsession...and gets stuck. Until I know how to get around that, I'm going to be sampling Openbox more.

Welcome to Apple Discussions.
If a program is not responding and you cannot "force quit" then you can launch Activity Monitor in Utilities. Under "my processes" you can choose that program and use the red "Quit process" icon at the upper left. That should do it rather than a restart.
But if many applications aren't responding both Apple and non-Apple there is a problem that should be sorted.
A good start would be to create a new account, name it "test" and see how your apps work in that User acct? (That will tell if your problem is systemwide or limited to your User acct.) This account is just for test, do nothing further with it.
Open System Preferences >> Accounts >> "+" make it an admin account.
Let us know and we'll troubleshoot this further.
-mj
[email protected]

Hostapd rt2800pci «Hardware does not support configured mode»

Hello
I am trying to use my fit-pc as a wifi access point. Here is wat lspci says about my wireless card:
lspci |grep Wireless
03:00.0 Network controller: Ralink corp. RT3090 Wireless 802.11n 1T/1R PCIe
It seems to be possible through with the mac80211 driver ( http://wireless.kernel.org/en/users/Drivers/rt2800pci )
In my hostapd.conf tell hostapd.conf to use nl80211.
Still when I do : #hostapd /etc/hostapd/hostapd.conf
I've got this message :
"Configuration file: /etc/hostapd/hostapd.conf
Hardware does not support configured mode
wlan0: IEEE 802.11 Hardware does not support configured mode (2)
Could not select hw_mode and channel. (-1)
wlan0: Unable to setup interface.
rmdir[ctrl_interface]: No such file or directory
zsh: exit 1 hostapd /etc/hostapd/hostapd.conf
Someone know if there is a particual configuration to use rt2800pci?

I had learned that the free DVD sets that Oracle ships are always for 64-bit systems. Owners of 32-bit systems will have to either download from http://edelivery.oracle.com or copy a distribution DVD from a friend. The 32-bit media can also be ordered from the http://oraclestore.oracle.com site for about $20USD.
Sorry for any confusion this may have caused.

CellEditor does not end edit mode when finished editing

Similar Messages

Maybe you are looking for