Changing Hyper-V host and cluster virtual IP addresses to new subnet/VLAN

I have a 2 node Hyper-V 2012 R2 failover cluster, managed by System Center Virtual Machine Manager 2012 R2, and I would like to change the IP addresses of the hosts and the cluster, in order to move them to a new subnet and VLAN. The existing and new subnets
are able to route to each other so all hosts will still be able to communicate throughout the parts of the process where they may be on separate subnets. There is also a dedicated cluster heartbeat network on its own subnet and VLAN that I am not altering
in any way.
The 2 hosts are configured with 4 nics in a team, with dedicated virtual interfaces for each of the following:
-Live Migration
-Cluster Heartbeating
-Host management/general traffic (the cluster virtual IP address is also on the same subnet as these interfaces).
It is the host management/general traffic addresses that I want to change. The interfaces were created and configured with the Add-VMNetworkAdapter, New-NetIPAddres and Set-VMNetworkAdapterVlan commands.
Please advise if the following process is correct:
1) Evacuate all the VMs from the first host to be changed and put it in maintenance mode.
2) Use Set-VMNetworkAdapter to change the name of the interface (the current name refers to the VLAN it's on)
3) Use Set-NetIPAddress to change the IP address and gateway of the interface as appropriate
4) Use Set-VMNetworkAdapterVlan to set the VLAN ID
5) Take the host out of maintenance mode and move all VMs off the other host
6) Repeat above steps on the other host
I know that I will then need to change the cluster virtual IP address, but I have no idea how to do this or where to look for that setting. Please advise!
Cheers.

Hi new_guise,
For changing cluster node's IP address please refer to the link below :
https://support.microsoft.com/kb/230356?wa=wsignin1.0
For changing VIP please refer to this article :
http://blogs.technet.com/b/chrad/archive/2011/09/16/changing-hyper-v-cluster-virtual-ip-address-vip-after-layer-3-changes.aspx
Best Regards,
Elton Ji
Please remember to mark the replies as answers if they help and unmark them if they provide no help. If you have feedback for TechNet Subscriber Support, contact [email protected] .

Similar Messages

Capacity Planning for Hyper-V individual host and Cluster

Hi Experts
I need to know some basic idea about Capacity planning for Hyper-V which requires Capacity Planning for Hyper-V individual host and Cluster.
I got attached info on websites but still not clear. Can someone link me to an effective website or help me to calculate the required sizing. W
Regards Suman B. Singh

Hi,
You might want to check out these websites:
http://www.microsoft.com/en-us/download/details.aspx?id=39057
http://technet.microsoft.com/en-us/library/dd277865(v=office.12).aspx
http://technet.microsoft.com/en-us/solutionaccelerators/dd537570.aspx
Cheers
Andrew

How to Install Integration service from hyper-v host to a virtual machine ?

i have around 100 Virtual Machine distributed on a cluster hyper-v cluster so i need to know how to install the upgraded version of integration service from the hyper-v host to all virtual machines
that has a mismatched version of the integration service using power-shell script ?

See this article:
PowerShell Script
for Automated Install of Hyper-V Integration Services in a VM running on Windows Server 2012 with Hyper-V V 3.0 Role using PowerShell Remoting
Mike Crowley | MVP
My Blog --
Planet Technologies

Cluster Virtual IP addresses - cluvfy utility error

Hi,
I've just about to install Oracle 10.2.01 Clusterware on a 2 node RAC running RHEL4 AS. I'm basically following Jeffery Hunters Guide - http://www.oracle.com/technology/pub/articles/hunter_rac10gr2.html
Each node has 2 ethernet cards - eth0 as public and eth1 as private. The hosts files contain entries for these, and a 2nd set of public IPs for use as VIPs
I've run the cluvfy utility for pre cluster installation checks and I'm getting a VIP error. The utility finds suitable interfaces for interconnects, but fails to find suitable interfaces for VIPs.
Has anyone any ideas what checks cluvfy is running and what might make them fail?
Thanks,
Thom
Message was edited by:
user470053

Hi new_guise,
For changing cluster node's IP address please refer to the link below :
https://support.microsoft.com/kb/230356?wa=wsignin1.0
For changing VIP please refer to this article :
http://blogs.technet.com/b/chrad/archive/2011/09/16/changing-hyper-v-cluster-virtual-ip-address-vip-after-layer-3-changes.aspx
Best Regards,
Elton Ji
Please remember to mark the replies as answers if they help and unmark them if they provide no help. If you have feedback for TechNet Subscriber Support, contact [email protected] .

How do I change my security questions and answers without setting up a new account. I can't remember the answers to the questions that they ask.

How do I change my security questions and answers without setting up a new account. I can't remember the answers to the questions that they ask.

1. See my User Tip for some help: Some Solutions for Resetting Forgotten Security Questions: Apple Support Communities.
2. Here are two different but direct methods:
    a. Send Apple an email request at: Apple - Support - iTunes Store - Contact Us.
    b. Call Apple Support in your country: Customer Service: Contacting Apple for support
        and service.
3. For other queries about Apple ID see Frequently asked questions about Apple ID.
4. Rescue email address and how to reset Apple ID security questions
5. For online assistance use Apple - Support - Express Lane

Hyper V hosts with Cluster Shared Volume do not provide Shared VHDX ability

Hi there, i've configured a pair of Hyper V hosts (UCS B230 M2) with SAN-Boot and access to a Shared Fiber Channel LUN.
No matter what I try, when I add a SCSI Adapter and one VHDX virtual disk to a VM, the option for "Advanced" never shows up therefore I can not share the VHDX file between another VM, which prevents any VM based clustering from working (IE: Clustered
SQL server)
Here are the settings I have configured:
The LUN has been formatted with NTFS
The Hyper V hosts have been configured as a Windows Cluster with an IP address and the Fiber Channel LUN configured as a Cluster Shared Volume
I follows the guides below
Create a CSV
https://technet.microsoft.com/en-us/library/dn265980.aspx
Create a shared VHDX
https://technet.microsoft.com/en-us/library/dn282283.aspx
Further details:
Two HyperV server core hosts built
Both joined to AD
Both joined to a Windows failover cluster
One 2TB Fibre Channel LUN presented from an EMC VNX array to both hosts
LUN formatted as NTFS
LUN created as a Cluster Shared Volume
Cluster Shared Volume present on both HyperV hosts
VM created within the Cluster Shared Volume
VM Booted up and Windows 2012 has been installed
VM gracefully shut down
Through the HyperV Manager, going in to VM settings,create a SCSI adapter, create a new VHDX file inside the CSV, the “Advanced” option for the VHDX is not present, therefore the option to make the VHDX file shared is not available
I have followed all steps in the Microsft Technet pages to create a CSV and a VM with Shared VHDX
I’ve cleared all settings and restarted multiple times, but this option is not present

Hi Sir,
>>No matter what I try, when I add a SCSI Adapter and one VHDX virtual disk to a VM, the option for "Advanced" never shows up therefore I can not share the VHDX file between another VM
>>Yes we are using Hyper-V Server 2012 R2
As we know Hyper-v server 2012R2 is a free version without GUI , I'm afraid you are not using Win 8.1 or other windows server 2012R2 to manage that free version hyper-v server .
Shared vhdx is a new feature came with 2012R2 , if use previous windows to manage 2012R2 you will not see "advanced" option (The blue circle belongs 2012 , the red circle belongs to 2012R2 ):
Best Regards,
Elton Ji
Please remember to mark the replies as answers if they help and unmark them if they provide no help. If you have feedback for TechNet Subscriber Support, contact [email protected] .

How to Change Hyper-V Host Physical NIC

I plan to replace a physical NIC on a Windows Server 2008 R2 Hyper-v host. What are the steps that I need to do. Thank you.

Delete the virtual switch for it and remove the NIC.
Install the new NIC and create a new virtual switch for it and assign it to the VMs that need it.
Also, a much better place to ask hyper-v questions is in the hyper-v forum:
http://social.technet.microsoft.com/Forums/windowsserver/en-US/home?forum=winserverhyperv
This forum is for the product Virtual Server 2005.

Hyper V Hosts and Domains

Can I have hyper V hosts connected to one domain then connect a VM to another domain.
I have three Quad port NICs- two will be connected to my DMZ domain and then to accommodate direct access I propose connecting one to my corporate LAN. I will then create the required vswitchs and place my direct access servers on DMZ switch and
the LAN switch for a 2 leg deployment?
Your thoughts please?

Sure, no problem with that. Each OS whether physical host or guest VM can join any domain they can reach.
Mark B. Cooper, President and Founder of PKI Solutions Inc., former Microsoft Senior Engineer and subject matter expert for Microsoft Active Directory Certificate Services (ADCS). Known as “The PKI Guy” at Microsoft for 10 years.

Current version of integration services on Hyper V host and ugrading versions on VM's

Greetings!
I am looking for where the latest version number of integration services is posted, so I may verify what it should be. I am able to query using powershell the vm's on the hosts and get a return of the current version installed. However, I seem to be
unable to find out the current version of IS on the hosts themselves. How do I get this information?

With all current releases of Hyper-V:
When you patch your Hyper-V Server and reboot, the vmguest.iso is generated dynamically to match the release of the Hyper-V Server.
This is historic and was designed to ensure compatibility of the ICs in the VM with the Services of the host.
That said, only Hyper-V 2012 R2 can give you the 'latest' integration components, but they might not function well if VMs are moved to older versions of Hyper-V. That is why 2012 R2 in a VM is 'not supported' on Hyper-V 2008 R2 or 2008 (for example).
In the future Integration Components will be through Windows Update (if your Hyper-V Server is 'Windows 10" or later):
http://blogs.technet.com/b/virtualization/archive/2014/11/11/hyper-v-integration-components-are-available-through-windows-update.aspx
Brian Ehlert
http://ITProctology.blogspot.com
Learn. Apply. Repeat.

Sun cluster: virtual IP address

Hi,
What is the virtual IP address and how to configure it?
For example, should it be defined in /etc/hosts? dns?
Thank you,

[[[s this correct to have apache HA?]]]
Apache can be set up as a failover resource (so it is active only on one node at a time) or a scalable resource (where it would be active on multiple nodes at the same time).
[[[Just an aside question: HAStoragePlus is NFS sharing? What is difference between NFS resource and mount resource (I saw Veritas differentiate between them)? In case I set up a shared disk, is it NFS or mount resource?]]]
HAStoragePlus is not NFS sharing. HAStoragePlus let's you create HA storage (it's called HAStoragePlus because there was an earlier generation data service (aka Clustering Agent a-la VCS) called HAStorage). This will let you wrap a shared storage device and fail it back and forth between multiple nodes of the cluster.
NFS sharing has to be handled using the SUNW.nfs Data service (or in other words, the NFS clustering agent) (ie only if you want to set up NFS as a HA service). Otherwise, you can use standard NFS.
Mount resource is (i'm guessing here) any resource that can be mounted. In other words, a Filesystem.
NFS resource is a resource that is shared out via NFS.
[[[Also, a basic question: The shared disk should not be mounted in /etc/vfstab. Correct? It should be only present when doing format on each node. Right? It is SCS that manages the mounting of the file system? This should be up before testing apache HAno?]]]
That is correct. Sun Cluster will handle mounting/unmounting the filesystem and importing/deporting the disk set (in Veritas world it is called a Disk group).
When you build your cluster resource group (aka VCS Service group), you will have to build the dependency tree (just how you would in VCS).
1) Create empty RG
2) Create HAStoragePlus Resource
3) Create Logical Hostname resource
4) Create Apache resource
5) define dependency of Logical hostname (Virtual IP) and HAStoragePlus (filesystem) so that apache can start.
At each stage, you can test whether the RG is working as it should before proceeding to the next level.

DHCP via Hyper-V VM, Server2012r2 Hyper-V host, clients not getting IP address

You have to authorize a dhcp server as Britv8 says. That's the only way it'll start dishing out leases. That's standard for Windows DHCP server in an AD Domain.
Also there's 0 reason to mention Hyper-V here. The whole point of virtualization is to do hardware level abstraction.

I recently encountered this. Setup:
Initial setup of the system was at a different location from its final destination, with different network equipment (switches) between the two. No teaming is involved, however.
Set up the system at its final destination, with DHCP via a Hyper-V VM (Server2012r2), Server2012r2 Hyper-V host, physical clients on the lan were not getting IP address.
The physical server box has a 4-port Intel Gigabit ethernet card.
I moved the setup (Hyper-V Virtual Switch manager) so that the interface for the DHCP server VM was isntead using one of two built-in Broadcom adapters.
While this topic seemed promising,
http://community.spiceworks.com/topic/251317-hyper-v-vm-not-leasing-ip-s-dhcp
unfortunately, "fiddling about" was not what I was looking for as possible solution.
My notes for the resolution:
Hyper-V system running...
This topic first appeared in the Spiceworks Community

Changing my Apple ID and its associated email address

For the past 6 years or so I have used the same Apple ID and email. It started out as an Aol account and is now my [email protected] as my Apple ID. I want to change my Apple ID and its associated email account to Gmail since that is what I use more often now. I see the option to change Email Address has next to it "This will be your new Apple ID", which is exactly what I want to do. I have two questions:
1) I will change the Email Address field to my Gmail address. Will this create any sort of confusion with the DRMed songs and videos I purchased in the past?
2) For posting on these discussion boards I have yet another Apple ID (created kind of by mistake, a long story). Is there any way I can merge the two?

I attempted to do the the same (similar) thing yesterday (Sept 2nd, 2010).
I wanted to change my current Apple ID used for iTunes Store (which was created years ago when I bought my wife an iPod) to be my Apple ID (created when I joined the Apple Developer program way before iTunes).
After changing the information and clicking the "Done" button, I received an error message that was positioned on the "Apple ID" box, which stated "this is not a valid email address". I assumed that the "email pattern filter" was erroneously attached to the Apple ID input box, so I contacted iTunes Store Customer Support.
*iTunes Store Customer Support response:*
+I'm very sorry for the inconvenience, since "<my.user.name>" is already an Apple ID it cannot be used for another iTunes account. At this point, it can only become it's own iTunes account.+
I'm posting my followup question below, in case anyone on the forum has these same questions or has any experience with actually doing what Apple proposed - create a new account to be used with an existing iTunes Library - and has any experiences they might wish to share.
*My followup question to iTunes Store Customer Support (waiting for reply):*
So, what are the implications of creating a new (second) iTunes account?
- Will I keep my same iTunes Library (i.e. Will all previous items be visible, when using the new account to purchase items)?
- How will this affect devices (iPhone, iPod) that are synched to the current iTunes Library?
So, I guess what I'm asking is; "How tightly coupled is the iTunes "account" information bound to the Library"?
I don't want to create a situation where:
- My iPhone and Apps gets wiped out when I sync because it sees a different "account name".
- My Library looks like I have "zero" items (Music/Videos/Playlist) because I've logged into iTunes with a different "account name"
I'm attempting to only change the iTunes Apple ID and email associated with the account for purchasing items through the iTunes Store. I want to preserve all other aspects of the current set up.
Is this possible?

How to change the full host and domain name on OS X Leopard...

I recently bought an iMac, and I'm trying to configure it for my network. The question I have is, how can I change the host name and domain name from Skuld.local to skuld.tolharadys.net?
After mucking around with a few searches on Google, I've gotten the domain name to stick since running domainname returns tolharadys.net. Also I can change the hostname as reported by 'hostname' temporarily by running 'hostname skuld.tolharadys.net' in Terminal.app. However, this isn't persistent after reboots. Ideas are welcome.

You would need a DNS server on your network configured to answer authoritatively for that particular subdomain.

Changing connection string host from localhost to IP address produces error

Hi all,
First of all, thanks in advance for your help. Second, I know next to nothing about Oracle database administration, so please be patient, but I want to understand things, rather than just running down the Google rabbit hole with guess-and-check until things happen to work and I don't know why.
I've got a connection string that I'm using to connect to a local Oracle database I'm using for testing. I have the 11g installed and the 11.1.0.7 64-bit client (as my application is a 64-bit application) installed, both locally on my development machine. I've got a connection working using the following connection string:
Data Source=(DESCRIPTION = (ADDRESS = (PROTOCOL = TCP)(HOST = localhost)(PORT = 1521))(CONNECT_DATA = (SERVER = DEDICATED)(SERVICE_NAME = mywindowslogin.path.to.me)));User Id=********;Password=********;However, when I change "localhost" to my IP address, my computer name, or anything else, I get "ORA-12541: TNS:no listener".
The tnsnames.ora in my database home is as follows - it was set up for me automatically when I installed the database. mywindowslogin.path.to.me doesn't point to anywhere, which I assume is correct, but my computer is on the path.to.me domain.
LISTENER_MYWINDOWSLOGIN =
(ADDRESS = (PROTOCOL = TCP)(HOST = localhost)(PORT = 1521))
ORACLR_CONNECTION_DATA =
(DESCRIPTION =
    (ADDRESS_LIST =
      (ADDRESS = (PROTOCOL = IPC)(KEY = EXTPROC1521))
    (CONNECT_DATA =
      (SID = CLRExtProc)
      (PRESENTATION = RO)
MYWINDOWSLOGIN =
(DESCRIPTION =
    (ADDRESS = (PROTOCOL = TCP)(HOST = localhost)(PORT = 1521))
    (CONNECT_DATA =
      (SERVER = DEDICATED)
      (SERVICE_NAME = mywindowslogin.path.to.me)
)How can I resolve this issue?
Edited by: Don on Jul 14, 2010 8:31 AM

Does setting the environment variable affect all installations? Only two of my four Oracle Homes have a tnsnames.ora file, or event a NETWORK/ADMIN location, so I'm not sure where to put tnsnames.ora in those Homes. I copied the tnsnames.ora for my database to the one other Home that had a NETWORK/ADMIN location, but I'm still getting "ORA-12541: TNS:no listener" if I don't use "localhost" as the host.
Thanks!
Edited by: Don on Jul 14, 2010 12:08 PM

I just updated to ios 6 and now I can't get through the set up. has made me change password three times and says my email address is already taken... well yeah, that's me. how to go on?

Its telling me to sign in using my email. When i do, it says that email is already taken. No, really? So now it wants me to change my password again. ***?
I can sign in to my account on my computer, so basically my ipad is junk now. Is there a way to uninstall the update.

Its telling me to sign in using my email. When i do, it says that email is already taken. No, really? So now it wants me to change my password again. ***?
I can sign in to my account on my computer, so basically my ipad is junk now. Is there a way to uninstall the update.

Changing Hyper-V host and cluster virtual IP addresses to new subnet/VLAN

Similar Messages

Maybe you are looking for