Changing WPA Username and Password

Hi Guys,
I am quite new to Wireless. would appriciate any help on this issue.
I am using a 891w as autonomous AP. I got some basic config from support forum.. Once configuration was done, i could see the SSID; but it was asking for username which i could not figure out. Here is the config below.
hostname ap
no aaa new-model
dot11 syslog
dot11 ssid WirelessNetwork
   vlan 1
   authentication open
   authentication key-management wpa
   guest-mode
   mbssid guest-mode
   wpa-psk ascii 7 cisco
bridge irb
interface Dot11Radio0
no ip address
no ip route-cache
encryption vlan 1 mode ciphers aes-ccm
encryption mode ciphers aes-ccm
broadcast-key vlan 1 change 30
ssid WirelessNetwork
antenna gain 0
station-role root
interface Dot11Radio0.1
encapsulation dot1Q 1 native
no ip route-cache
bridge-group 1
bridge-group 1 subscriber-loop-control
bridge-group 1 block-unknown-source
no bridge-group 1 source-learning
no bridge-group 1 unicast-flooding
bridge-group 1 spanning-disabled
interface Dot11Radio1
no ip address
no ip route-cache
encryption vlan 1 mode ciphers aes-ccm
encryption mode ciphers aes-ccm
broadcast-key vlan 1 change 30
ssid Wirelessnetwork
antenna gain 0
dfs band 3 block
channel dfs
station-role root
interface Dot11Radio1.1
encapsulation dot1Q 1 native
no ip route-cache
bridge-group 1
bridge-group 1 subscriber-loop-control
bridge-group 1 block-unknown-source
no bridge-group 1 source-learning
no bridge-group 1 unicast-flooding
bridge-group 1 spanning-disabled
interface GigabitEthernet0
description the embedded AP GigabitEthernet 0 is an internal interface connecting AP with the host router
no ip address
no ip route-cache
interface GigabitEthernet0.1
encapsulation dot1Q 1 native
no ip route-cache
bridge-group 1
no bridge-group 1 source-learning
bridge-group 1 spanning-disabled
interface BVI1
ip address dhcp client-id GigabitEthernet0
no ip route-cache
cns dhcp
end
Please help me change the username and password for the SSID.
I hope in the able example the password is cisco.
Thanks you.

Hi,
This should be asking you only the password not the username as you have confired with wpa-psk. What client device are you testing this with? If this is wondows machine please choose your sececurity as WPA-Personal on the wireless profile and then it would asked for the Security Key..You will have to enter your password there. The password from the configuration i can see it as cisco.
wpa-psk ascii 7 cisco
Hope thats helos,
Regards
Najaf
Please rate when applicable or helpful !!!

Similar Messages

Changed icloud username and password can't access other devices

I have three devices from which I use the same iTunes and ICloud account. I changed my username and password on the accounts yesterday. Now I am only able to get it to work on my IPhone 5S. My daughter's IPhone 4 and my IPad will not accept the new passwords. I can't access FaceTime or IMessage on those devices as it keeps prompting me that it is incorrect and to reset. If I reset, it won't work on my IPhone 5S. Help!

Welcome to the Apple community.
If you mean that Find My Phone is asking for a password to a different Apple ID to your current Apple ID and that ID is a previous version of your current ID, not an entirely different one.
This feature has been introduced to make stolen phones useless to those that have stolen them.
However it can also arise when the user has changed their Apple ID details with Apple and not made the same changes to their iCloud account/Find My Phone on their device before upgrading to iOS 7, or if you restore from a previous back up made before you changed your details and some other circumstances.
The only solution is to change your Apple ID back to its previous state with Apple at My Apple ID using your current password, you don’t need access to this address if it’s previously been used with your Apple ID, once you have saved these details enter the password as requested on your device and then turn off "find my phone" and delete the account from your device. It may take a short while to remove the account.
You should then change your Apple ID back to its current state, save it once again and then log back in using your current Apple ID. Finally, turn "find my phone" back on once again.
This article provides more information about Activation Lock.
This is answer is provided from my own database of boilerplate responses and the content was last reviewed and tested on: 2014/05/23

I have changed my username and password but the apps are still asking for my old username and password. How do I change that

I have changed my username and password for my apple account but the apps previously linked to it are still asking for the old info. And I don,t know it so that's why I updated it

Apps are permanently tied to the ID and password used to purchase them. If you do not remember that information, you cannot update them. If you ned these apps, you will have to repurchase them under your new ID.

Changing DB username and Password for APEX

Hello Guys:
My APEX application is currently connected to the Main database, and now the business decided they want a user to be created with the main database only for APEX.
My main database is called ARRA, and user within the ARRA schema called ARRAAPEX was created given a diffrent username and password.
I see in the Administrative services I can only tell it to which schema to connect to, but where do I specify the username and password for the database user to be used by APEX?
Thank You For Your Help
Adel

Thank You for your reply Roel. What I meant to say is Logging to the ARRA schema using the username and password associated with ARRAAPEX would allow me to see the Date last edited field that has been added to the ARRAAPEX. ANd I am not able to see that at this moment becuase I am logging to to ARRA using the ARRA username and password.
When we setup a workspace and then associate a schema with that workspace, where do I specify the username and password that the workspace should use to access the schema? Or if a username and a password are not needed then how does the workspace access the schema?
Thank You
Adel

I have changed my username and password

I have changed my id and password i cant get my paid apps back

Apps are permanently tied to the ID and password used to purchase them. If you do not remember that information, you cannot update them. If you ned these apps, you will have to repurchase them under your new ID.

Changing apple username and password on your iPad

Some water got into my iPad 1. I put it away in a drawer and bought the iPad 2. About eight months later I came across the first iPad, so I plugged it in. Sure enough it started working again. It had all my info on it and I want to give it to my grandkids. How would I take my apple username and password off of it?

I would say your best bet for this would be for you to do a update and restore in iTunes on a computer to make sure none of your info is on the device. If you do not feel comfortable with that then you can sign out of the iTunes store and App store by going into Settings > (iTunes and App) Store > View Account > Sign Out

Changing Icloud username and password

I have changed my apple ID and password on my iphone 5 but I cannot change my icloud user name and password, altough it has changed on my pc, how can I change it on my iphone

Settings > iCloud > Delete Account. Then sign in with your other ID.

VC Change username and password for web services

Hi everybody
I need to change the username and password into the portal of some web services that have already been created portal is consuming these web services a XI
Thansk
Ivan

it is ok ....
thank you....
i have now this issue:
i need to add new E1 to be in the same trunk for previous E1 which is for Abdali. new E1 will not have signal it depeneds at old one timeslot.
i used this for new E1:
prov-add:nailedtrnk:name="1033",srcsvc="ss7p-jtc-abdali",dstsvc="naspath1-abdali",srcspan="ffff",dstspan="0",srctimeslot="33",dsttimeslot="33",spansize=31
for old one this:
prov-add:nailedtrnk:name="1002",srcsvc="ss7p-jtc-abdali",dstsvc="naspath1-abdali",srcspan="ffff",dstspan="0",srctimeslot="2",dsttimeslot="2",spansize=30
============================
at AS5400 i used to add new E1:
controller E1 7/2
framing NO-CRC4
pri-group timeslots 1-31 nfas_d primary nfas_int 1 nfas_group 0
Is this true or there are other commands i should use?
OLD E1 is configured as:
controller E1 7/0
framing NO-CRC4
channel-group 0 timeslots 1
pri-group timeslots 2-31 nfas_d primary nfas_int 0 nfas_group 0
description Connection to Abdali
interface Serial7/0:0
no ip address
encapsulation ss7
channel-id 0
interface Serial7/0:15
no ip address
encapsulation hdlc
isdn switch-type primary-ni2c
isdn incoming-voice modem
isdn map address . plan isdn type network
isdn rlm-group 0
no isdn send-status-enquiry
isdn negotiate-bchan resend-setup
isdn bchan-number-order ascending
no cdp enable
any help please for correct commands i shall use? please see attached file for details.

Script Updater to change username and password

Can the script updater change the username and password for a bunch of test? I tried using the Global search and replace but it was not able to find the string. Please help?

If the password is stored in the test it's self you can find it by opening the test file xxx.mom and preform there a search and replace.
Perhaps it's better to connect the password to a variable by connecting it to a databank source. So the password is stored only once. Saves a lot of maintainance.
-Theo

My iphone sorry, I restore my iphone ask Apple ID username and password? I entered, it can not reported to unlock my ID. I used iforgot the ID is not changed. I have icloud how active threads. I used ios 7.0.6. thank

restore my iphone, iphone Apple ID requirements? but not to open it. I use iforgot ID. not be. I did not change the username and password. i need help. I used ios 7.0.6. thank

Hi tuyet nhu nguyen,
Given that you recently restored your iPhone, it sounds like you may be having issues with iOS Activation Lock. You may find the following articles helpful:
iCloud: Activation Lock
http://support.apple.com/kb/PH13695
iCloud: Find My iPhone Activation Lock in iOS 7
http://support.apple.com/kb/ht5818
Regards,
- Brenden

Setting username and password

Hello,
I'm trying to create local users in my Switch /Routers with different privileges. My requirement is when the user telnets to Switch /Router , he should get a screen with username rather than using login command from unprivileged mode . Now to to login , I telnet to Router and from there(unprivileged mode) I use login command to put the user name and then password.
Regards,
Raju

Try this:
username helpdesk prvilege 1 password helpdesk
username admin privilege 15 password admin
line vty 0 4
login local
line con 0
login local
Of course change the usernames and passwords according to your schema, but the key to this config is the 'login local' command on vty and con. This will prompt the user for username and password before even allowing them to access the user prompt.
HTH,
Jason

HT5624 Hi, I have an iPad with a different iCloud username and password then my Apple ID. I forgot my iCloud password and the email I used is no longer working. How do I change my iCloud I'd and password to match my Apple ID one? Thanks in advance

Hi, I have an iCloud account with a different iCloud username and password then my Apple ID. I forgot my iCloud password and the email I used is no longer in use. How do I change my iCloud Username and password to match my Apple ID one? Thanks in advance

Hi Cplantin!
Here is an article for you that will help you with this question:
iOS 7: If you're asked for the password to your previous Apple ID when signing out of iCloud
http://support.apple.com/kb/TS5223
Take care, and thanks for visiting the Apple Support Communities.
-Braden

I have Iphone 4s, and the phone will activate itself again. How do I get changed Apple ID on my phone so that I get using the new username and password that is verified? I would like an answer as soon as possible ... Thank you very much.

I have Iphone 4s, and the phone will activate itself again. This I have verified, but when I shall put this onto my phone, so the phone will not approve the newusername and password. How do I get changed Apple ID on my phone so that I get using the new username and password that is verified? Silly to buy a new phone just for this .... The phone is almost three years old. How long can weexpect this to last? I would like an answer as soon as possible ... Thank you very much.

It sounds like your device might be in Activation Lock. Is it asking your to enter in an Apple ID & password, but only showing you the first letter of the email address and then some dots? Example: j•••••@icloud.com?
If so, do you recognize that email? Do you have an Apple ID that fits the same format? If so, then go to www.cloud.com, log in with that Apple ID & password, and see if under Find My iPhone it shows this device. If so, turn off the device, then remove the device from the list.

I changed my i tunes username and password a while ago, but there are still remnants of the old one appearing. I now want to wipe my iPhone, but can't as it is logging me in with my old username, and asking for the old password, which i can't remember.

I changed my itunes username and password a while ago, but it still sometimes keeps popping up. I now want to erase my iphone, but i can't because it is asking me for my old password, which i can't remember. My old user name was an email address, however i no longer have the email address!! Help please community.

https://iforgot.apple.com/
iOS: Unable to update or restore - http://support.apple.com/kb/HT1808 - recovery mode (e.g., cannot connect to computer last used to sync device, iTunes still asks for a password)

I am the founder of a non-profit organization, a donor had just given us her used iBook G4. What do I need to do to wipe out her "stuff", change username and password, start all over new. We will use this iBook in our learning center in Saigon, Vietnam

To good citizens of the MAC world,
I am the founder of a non-profit organization, we are caring for 6,200 orphans and street kids in Vietnam. A donor had just donated her used iBook G4 for us to use in one of our several "learning centers" in Vietnam. Folks sometimes donating PC but this is the first time we ever received a MAC.. :-) I would like to know how to start this iBook all over new: change username and password. I am looking so forward to bring it to Saigon in a few days and let our children experience MAC ... I am a 2 years MAC users and I have no intention to return to the Dark side. Please help. I have the original OS disk. Thank you so much.

There should be no need to zero the hard drive.
Using the Restore discs that came with the iBook when it was new, restore the system software using the appropriate instructions which you can find through a link contained in this Apple Knowledge Base article:
http://support.apple.com/kb/HT1561?viewlocale=en_US
Good luck with it.

Changing WPA Username and Password

Similar Messages

Maybe you are looking for