CLD Front Panel Question

I understand that the front panel is now provided to you for the CLD.  Is the provided front panel fully functional, or does it require modification?
For example, do properties such as mechanical action and boolean text require modification on the test taker's part, or is the front panel fully functional?
I can't imagine these things taking very much time, but it is good to know what to expect going in.
- Tom
Solved!
Go to Solution.

The folder hierarchy provided to you for developing your solution consists of the (named) main VI, input file (where applicable), Controls and SubVIs folders.
Main VI: This includes the front panel with the corresponding terminals on the block diagram. Where front panel objects are grouped and typed defined, the .ctl file will be provided in the Controls folder. Some functionality may be provided with the controls (for example: Data Entry limits), but it is the developer’s responsibility to check and modify to the needs of their solution. For the main VI, you must customize the following:
Icon: Customize the icon. Recommendation: Use simple icons: Example: . Avoid developing fancy, graphical icons
VI Documentation: Briefly describe the VI in the VI Documentation. See following example.
Description and Tip: Provide either a very brief Tip strip or Description for Main VI objects. Example: “Withdraw funds”, “Check Balance”, “Stop Application”
If you have any further questions, please email [email protected]
Zaki Chasmawala | Certification Development Group Manager | Training & Certification | National Instruments | [email protected]

Similar Messages

  • A different Front Panel question

    Just to spice up the board, I'll ask a different question about the front panel. ?I have the X-Fi Fatalty board with the front panel and for the past 2 years have not used the front panel.
    My question: Can I pull the front panel and set it asideI don't use it and the ribbon cable is cluttering up the wiring in my, already cramped, case. ?Will it operate with just the PCI card?
    Thanks.

    Absolutely. I have used mine many times without the front panel. I add it back when I dont want to reach around to the rear to plug in a MIC and I certainly dont use my headphone jack on my center channel speaker for headphone output.

  • Dynamic cluster/array follow up question - front panel

    Thanks for the responses to my last question - they were great and fast!
    I'm still stumped on how to create the front panel. It doesn't really matter whether it is an array or cluster. It sounds like either way, once I have it I can autoindex through it. The basic application here is that I have a VI that will store one XY plot to our database. I'd like to wrap that in a VI that will take N XY plots and store them all in our database regardless of what N actually is. So in terms of creating the front panel, I tried to create an array control and drop a XY graph in it, but it doesn't seem to like that. It said that I hadn't added an element to the array. I also tried to drop a XY graph into a cluster control and that cleared the broken run arrow, but wouldn't I have to know how many XY graphs are being passed in? It seems like I'd have to put one graph in the cluster control for each graph coming which defeats my purpose? Remember I won't know how many XY graphs are coming into my VI in the array or cluster. Anybody know how I can set up the front panel?
    Again thanks for the quick replies!!!
    Best Regards,
    Steve

    Look at the attached VI.
    It has a single XY graph inside a cluster container, and that is inside an array container.
    With this setup, it wouldn't matter how many graphs you pass to the subVI since it's an array, it will take whatever is passed to it.
    Ed
    Ed Dickens - Certified LabVIEW Architect - DISTek Integration, Inc. - NI Certified Alliance Partner
    Using the Abort button to stop your VI is like using a tree to stop your car. It works, but there may be consequences.
    Attachments:
    XY Graph in Array.vi ‏13 KB

  • Will I lose points on the CLD Exam if I use a Launcher vi in addition to the provided Front Panel?

    Hi!
    In this thread: https://decibel.ni.com/content/message/50512#50512, MattP directed me to this Certification Board.
    If I use the Actor Framework in a CLD exam, will I lose points for launching the Front Panel? For two specific examples of what I mean, please refer to the solutions submitted here:
    ATM: http://forums.ni.com/t5/Certification/Sample-Exam-Solutions-for-Review/m-p/2380868#M728
    Boiler: http://forums.ni.com/t5/Certification/Sample-Exam-Solutions-for-Review/m-p/2385580#M738
    Thanks!
    Solved!
    Go to Solution.

    Hi,
    You will not loose points for using the launcher, and not documenting the message classes.  The folder structure is also fine.
    Do document the other VI's, actors,and SubVI's.   Remember be brief with documentation.
    Mark Ramsdale
    Project Manager and CLD
    Customer Certification and Training at National Instruments

  • Question on closing Front Panel references

    I'm manipulating controls on the Front Panel of my VI.  In doing this, I open a slew of references (to the VI, to the Front Panel, to its Panes, and to the objects on the Front Panel).  Normally, before exiting the VI, I carefully close them (in LIFO order, of course), but a question has arisen:
    I want to "export" a series of references to Boolean controls for use in succeeding VIs.  No problem, while enumerating the controls (see above), I simply identify the Boolean references and build them into an array that I pass out.  First question -- does anything "go wrong" if I also do a "Close Ref" in the main loop (after adding the reference to the array, of course)?  [At present, I'm only doing a Close Ref on the non-Booleans].  Logic says this should be OK, as the Close Ref is mainly doing "garbage collection", and I've done a "copy" operation in building my array, but to a persistent structure.
    Second question -- in my "cleanup" routine, I noticed I was "double-disposing" of the references, that is, I did a Close Ref on my array of Boolean References, but also was enumerating the entire Front Panel (as I did when I opened it) and disposing of the references that it found.  Again, this should be no problem, but (in principle) I'm doing a Close Ref on two references to the Boolean control.  It occurs to me that this is not really logical either -- I should be able to simply "abandon" the array of references -- although it takes up memory that can be "reclaimed" for other uses, the fact that it is an array of RefNums is a "so what" -- the contents of the array could have been a numeric or other "solid" data type.
    Does this make sense?  To summarize, what I'm trying to do is to "extract" some RefNums to Front Panel objects for later use.  In the "extraction" process, I must open (and create references to) multiple objects, including RefNums to my "objects of interest".  What I think I can (and should) do, once I've copied the RefNums I need, is to dispose (Close Ref) all of the RefNums that I opened during the extraction routine, and do something equivalent when I do the subsequent "cleanup" (which undoes any modifications I made as part of the extraction).
    Comments welcome.
    Bob Schor

    I usually store the ref. at the beginning of my program, in Functional Globals, and i close them when the program does not need them any more. 
    I think this is the right approach. And it is simple

  • Audigy 2 ZS Newbie Question? Is my front panel working rig

    WHOA! I'm new with this card but not posting..don't know what happened with that blank post..(The cat stepped on the "Enter" key...Yea..thats it..thats the ticket)
    Anyway, I just hooked up my card and installed my front panel and I have a couple of dumb questions:
    . Should the front panel be lit's What is the led abouve the MIDI for? Does it just light when MIDI is pluged in?
    2. I have almost no volume at the headphone jack. I have heard others say that it mutes their speakers when they plug into the HP jack, Mine does not.
    3. Wait, is that an LED or the pick up for the remote? Hmmm..just thought of that?
    The remote does work, albeit poorly. The firewire on the front panel works, I can't test much else. I guess my main question is: Does the front panel light up? It just looks like that there is no power getting to it..
    I want pretty lights!! :-)
    Thanks for help
    Phil

    oh man thanks a lot! i knew about that option too, but i completely forgot about it!! lol
    and let this be a reminder to anyone else dumb enough to forget about that little option!
    thanks again

  • [General Question] redrawing and updating front panel objects

    Hello,
    I have several questions on this topic.
    1)  Is there a difference between redrawing and updating the front panel? (I assume so, but when a control is updated it will be redrawn at the same time, right?)
    2)  Is redrawing = rendering? In the case of decorations I think they need only to be rendered once (if fix/static) and stay in memory so that it is available for the gfx-card...
    3)  Are decorations redrawn or updated by LabView with every loop?
    4) Is there a way to prevent LabView from redrawing and/or updating front panel objects (like controls, indicators and decorations)?
        When I put indicators into case-structures they are only updated when the case in which they are placed is executed but they will be obviously still redrawn.
        In another case when I disable visibility of those indicators they will not be redrawn anymore but be updated in the background.
        So when I put these indicators into a case-structure and combine it with toggling the visibility I could stop LabView from updating and redrawing them.
        Is this correct?
        Is there another way to prevent LabView from redrawing single objects? (at best leave them somehow visible)
    Many thanks in advance!

    Nocturn wrote:
    Hello,
    I have several questions on this topic.
    1)  Is there a difference between redrawing and updating the front panel? (I assume so, but when a control is updated it will be redrawn at the same time, right?)
    2)  Is redrawing = rendering? In the case of decorations I think they need only to be rendered once (if fix/static) and stay in memory so that it is available for the gfx-card...
    3)  Are decorations redrawn or updated by LabView with every loop?
    4) Is there a way to prevent LabView from redrawing and/or updating front panel objects (like controls, indicators and decorations)?
        When I put indicators into case-structures they are only updated when the case in which they are placed is executed but they will be obviously still redrawn.
        In another case when I disable visibility of those indicators they will not be redrawn anymore but be updated in the background.
        So when I put these indicators into a case-structure and combine it with toggling the visibility I could stop LabView from updating and redrawing them.
        Is this correct?
        Is there another way to prevent LabView from redrawing single objects? (at best leave them somehow visible)
    Many thanks in advance!
    redraw vs update
    Yes threr is a difference. A control is redrawn when LV decides to update the GUI. Look into "syncronous" setting for controls that forces update when value changed. These tags and thesse tags may help out abit.
    Q2
    Not sure about equality but decoartion may need redrawn if there is overlap of chanable objects.
    Q3
    i have observed decorations that failed to update on occation so I suspect they are only update when required.
    Q4
    LV will update the value for a hidden control but will not update its image. Same if the object is ona hidden tab page.
    No wawy that I know of to prevent an update of a single object with out going to extremes. The Front pnale property "DeferFPupdate" will inhibit FP updates while true and allow then when set false. I use this when doing a lot fast GUI updates so allow the changes to accumulate and be apllied only once.
    Ben
    Ben Rayner
    I am currently active on.. MainStream Preppers
    Rayner's Ridge is under construction

  • X-Fi Platinum Front panel Power QUESTION

    ? Hi All, I have X-Fi Platinum. Does the front panel require A power connection. If so what kind of connector do I need? Run from the card to the front panel? Cant find manual on line!? THANKS IN ADVANCE

    This requires a four pin floppy power connector. If your case does not have one you can find a molex to floppy adapter very simply on online retailers.

  • Question about subvi front panel

    I want to call a subvi in the main program and do like
    this:
    1. When the main program calls the subvi, the subvi shows its front
    panel and executes.
    2. After the subvi finishes, it can close the front panel.
    Now, I meet a problem: I can popup the subvi node setup dialog to enable
    "show front panel when called", which implements the first one, but I
    can not close the front panel until originally closed(main
    program stops). How can I close the subvi's front panel(after it
    finishes running) even when the main program is still running?
    Thanks in advances.
    Sent via Deja.com http://www.deja.com/
    Before you buy.

    In article <[email protected]>,
    "Remco Breen" wrote:
    >
    > [email protected] wrote in message <[email protected]>...
    > >In article <[email protected]>,
    > >"Kevin B. Kent" wrote:
    > >> [email protected] wrote:
    > >>
    > >> > Now, I meet a problem: I can popup the subvi node setup dialog to
    > >enable
    > >> > "show front panel when called", which implements the first one,
    but
    > >I
    > >> > can not close the front panel until originally closed(main
    > >> > program stops). How can I close the subvi's front panel(after it
    > >> > finishes running) even when the main program is still running?
    > >
    > >
    > >
    > >
    > >> Select the "close front panel if originally closed" option.
    > >> in addition to the "Show front panel when called"
    > >>
    > >> Kevin Kent
    > >
    > >
    > >I have tried this, in this way, the subvi's front panel is closed
    only
    > >after the main program stops. In fact, what I want is to close the
    > >subvi's front panel even the main program is still running.
    > >
    > >
    > >zhljh
    > >
    > >
    > >Sent via Deja.com http://www.deja.com/
    > >Before you buy.
    >
    > Another option would be to open a VI reference (found under
    "application
    > control") and tie that to a property node and select the property
    "front
    > panel.open". Change it to a control and attach a boolean false to it
    when
    > you like to close.
    >
    > RB.
    >
    I think a more elegant way of closing the SUB VI is to start off the way
    that Remco states regarding opening a VI reference. Only in the Sub VI,
    you should program a Terminate control (such as an Abort button to exit
    from a While loop... or something similar) and via the VI reference,
    select the 'Set Control Value' method to gracefully stop the Sub VI
    execution. Of course the Sub VI will have to set the close if originally
    closed attrib set.
    There is a great source of example LabVIEW apps at:
    http://digital.ni.com/explprog.nsf/web%2Fswgrp?OpenView&Start=1&Count=50
    0&Expand=3.7#3.7
    In particular, see "Stopping a Running SubVI from the Main VI Using VI
    Server" example. It demostrates this techniques better than I can
    explain it. Hope this help.
    Rick
    Sent via Deja.com http://www.deja.com/
    Before you buy.

  • Front Panel Audio - P7N Sli Platinum Question

    I am having trouble getting the front panel audio working - I want it set up so that when I plug my headphones in the speakers mute and the headphones take over.
    I have the following:
    Case - ThermalTake Armor VA8003BWS - http://www.thermaltake.com/product/Chassis/fulltower/armor/va8003bws.asp
    MB - P7N SLi Platinum
    Sound Card - Create Labs Xfi Gamer
    I have done the following:
    1. Disabled onboard audio in Bios (should I turn this back on?)
    2. Went into Creative Console Launcher and checked the 2 options that I want it to automatically enable headphone settings and mute speakers when headphone jack is connected.
    3. Connected 10 pin wire in case labeled (Azalia) to the motherboards Jaud1 (my MB manual says it is Azalia 1.0 compliant). The case also has an AC'97 connection (on the same wire as Azalia but I didn't use this because of what I read in MB manual about Azalia 1.0 compliant).
    4. The case also came with this 10 pin black block that has all the Azalia descriptions on the side (Port 1 L, Port1 R, Port2 R, Sense_Send, etc. - I tried plugging the Azalia connector into this and then this into the Jaud1 but still nothing).
    Not sure if it matters but my headphones are Plantronics Gaming Audio 770 (not USB).
    Any suggestions?

    Quote from: [LT]Eternalbliss on 21-June-08, 03:43:49
    I've just recently had this similar problem. I think the issue in your case is step 3. I believe you should connect the Azalia 10pin wire to your X-fi card, not the mobo.
    My problem was that i had connected AC97 10pin wire to my X-fi, after which plugging in my headphones didn't mute my speakers.
    That was the problem - works great now!  Thanks

  • Disable controls on front panel (Bacic question)

    How do i make the numeric controls on the front panel disable when the VI is running??

    1. Create a reference to the control you wish to enable/disable. (You can right click on the control on the block diagram and select "Create >> Reference" to do this).
    2. Wire the reference to a Property Node (found in Application Control on the Functions Palette).
    3. Right click on the Property Node and choose "Change All To Write".
    4. Left click on the Property Node and choose "Disabled" from the list.
    The state of the control will depend on the value you wire to "Disabled" terminal of the Property Node. 0-Enabled, 1-Disabled, 2-Disabled and Grayed Out.
    Hope that answers it for you.
    Nick
    "You keep using that word. I do not think it means what you think it means." - Inigo Montoya

  • Open and close a vi front panel dynamicall​y

    I created a main vi panel that display all the signal names.  I like the main vi to open a new plot screen when I double click on the signal name.  I was able to do that using invoke node. But I when I close the plot screen by clicking on the Window "Close" button, the main vi was not able to open a new one again.  So I disabled the Window "Close" button and only use the "Stop" button coded in while loop in the blockdigram of the plot screen.  It worked, but the plot screen is still open and changed to editing mode.  Is there an easy way to close the plot screen by only one click.  Another question is that how does the main vi can open multiple plot screens.  Thanks for your advice.

    I think I know what happens:
    If you close the front panel of a sub-vi, the code is still running, so the VI doesn't terminate and somehow you can't address it (it don't know how you communicate with your sub-vi).
    So in your sub-vi you should monitor the panel-close event, and finish the code of the VI and finish the VI
    Ton
    Free Code Capture Tool! Version 2.1.3 with comments, web-upload, back-save and snippets!
    Nederlandse LabVIEW user groep www.lvug.nl
    My LabVIEW Ideas
    LabVIEW, programming like it should be!

  • Open sub VI front panel in a tab-- Possible?

    Well, the question is basically in the subject: Is it possible to call sub VI's and display their front panel in a tab. I do NOT wish to have the front panel in a new window when called.
    Solved!
    Go to Solution.

    _Faust wrote:
    Well, the question is basically in the subject:<...>
    The answer is also basically in the picture:
    You can find SubPanel element in the same palette as the Tab Control container. Place a SubPanel on the Tab Control and wire a reference of the VI whose front panel you want to display.
    Message Edited by Giedrius.S on 02-13-2010 11:08 PM
    While evaluating my code please have in mind that I am a LV novice. Therefore sometimes my code might violate some coding rules that I have to learn about myself. But how else could I do that...
    Chart zoom with "Mouse Over" effect

  • Floating VI front panel

    I have question regarding keeping a specific VI front panel always "On Top" of any other front panels(Sort of like toolbar pallete floats over the "main" window in LabVIEW). I can set the front panel properties to be a dialog (ModaL) but then I don't have access to menu or any other controls on the other front panels. I can set the front panel properties to normal, but when the operators click on main front panel the other front panel goes to the back. We have very very very novice computers and they get confused and they can't "find" the "other front panel".
    Any help would be greatly appreciated.
    Thanks

    If you have LabVIEW 7.0 or 7.1, there is another selection in Window Apperance setup called 'Floating' that does exactly what you want.
    If you have an earlier version, this Dev Zone thread may help.
    Ed
    Ed Dickens - Certified LabVIEW Architect - DISTek Integration, Inc. - NI Certified Alliance Partner
    Using the Abort button to stop your VI is like using a tree to stop your car. It works, but there may be consequences.

  • Multiple VI on a Single Front Panel

    Probably a simple question but I'm having trouble figuring out how to do it.
    First, I have LabView 2010, Professional Development System
    I have been trying to learn LabView the hard way.  I've been reading the documentation, starting with Getting Started and testing VI and front panels for instruments we have in the lab.  I can run the examples and control the instruments individually through individual front panels.
    My question is, "How do I create a single front panel (or application), that consists of several instruments?"
    For instance, I have an Agilent 34970, Data Actuisition Unit.  And I can create a front panel (and block diagram) to read data from the instrument input terminals, operate switches, etc.  I also have a GenSys Power Supply and can control the voltage levels and on/off, from it's front panel. But the two panels (and block diagrams) are not linked.
    I have other instruments but understanding how to link two different block diagrams (with single front panel), will help me figure out how to expand it to multiple.
    How do I integrate multiple block diagrams (or VI), with a single front panel (and block diagram) such that I can use loops, structures and conditions in one, that can be used to control the programming in the other.  For instance, say I want to sample an input on the 34970 and if it's between x and y voltage, then set the power supply to another voltage and test again. This requires two VI acting in synchronization with each other. 
    I can do each seperately but am stuck on how to integrate these into a single application.
    Thanks,

    Hi Mike,
    Patricia B is right... You can try sub vi. But if you really want to put two vi's in a same window you can try sub panel. But it is not recommanded... Check these vis....
    <<Kudos are welcome>>
    ELECTRO SAM
    For God so loved the world that he gave his one and only Son, that whoever believes in him shall not perish but have eternal life.
    - John 3:16
    Attachments:
    Try this.7z ‏26 KB

Maybe you are looking for