Client in same WLAN cannot ping eachother

WiFi clients in same WLAN(ssid) cannot ping eachother.
AP's are in Flexconnect mode, WiFi clients are able to access network and internet etc, but not able to ping eachother.
whereas, Lan devices from same network are able to ping these wifi client.
There is no firewall or ACL as such in WLC or local switch. Also Peer-to-Peer blocking is 'disabled'.
Also i'm able to see client arp entries in WLC and local switch.
What could be causing this issue, and how can we resolve this?
Pls comment.

Did you check if WiFi clients are able to ping LAN Devices on the same network or not?

Similar Messages

Need HELPS! ASA 5505 8.4 Cisco VPN Client cannot ping any internal host

Hi:
Need your great help for my new ASA 5505 (8.4)
I just set a new ASA 5505 with 8.4. However, I cannot ping any host after VPN in with Cisco VPN client. Please see below posted configuration file, thanks for any suggestion.
ASA Version 8.4(3)
names
interface Ethernet0/0
switchport access vlan 2
interface Ethernet0/1
switchport access vlan 2
interface Ethernet0/2
interface Ethernet0/3
interface Ethernet0/4
interface Ethernet0/5
interface Ethernet0/6
interface Ethernet0/7
interface Vlan1
nameif inside
security-level 100
ip address 172.29.8.254 255.255.255.0
interface Vlan2
nameif outside
security-level 0
ip address 177.164.222.140 255.255.255.248
ftp mode passive
clock timezone GMT 0
dns server-group DefaultDNS
domain-name ABCtech.com
same-security-traffic permit inter-interface
object network obj_any
subnet 172.29.8.0 255.255.255.0
object service RDP
service tcp source eq 3389
object network orange
host 172.29.8.151
object network WAN_173_164_222_138
host 177.164.222.138
object service SMTP
service tcp source eq smtp
object service PPTP
service tcp source eq pptp
object service JT_WWW
service tcp source eq www
object service JT_HTTPS
service tcp source eq https
object network obj_lex
subnet 172.29.88.0 255.255.255.0
description Lexington office network
object network obj_HQ
subnet 172.29.8.0 255.255.255.0
object network guava
host 172.29.8.3
object service L2TP
service udp source eq 1701
access-list VPN_Tunnel_User standard permit 172.29.8.0 255.255.255.0
access-list VPN_Tunnel_User standard permit 172.29.88.0 255.255.255.0
access-list inside_access_in extended permit icmp any any
access-list inside_access_in extended deny tcp any any eq 135
access-list inside_access_in extended deny tcp any eq 135 any
access-list inside_access_in extended deny udp any eq 135 any
access-list inside_access_in extended deny udp any any eq 135
access-list inside_access_in extended deny tcp any any eq 1591
access-list inside_access_in extended deny tcp any eq 1591 any
access-list inside_access_in extended deny udp any eq 1591 any
access-list inside_access_in extended deny udp any any eq 1591
access-list inside_access_in extended deny tcp any any eq 1214
access-list inside_access_in extended deny tcp any eq 1214 any
access-list inside_access_in extended deny udp any any eq 1214
access-list inside_access_in extended deny udp any eq 1214 any
access-list inside_access_in extended permit ip any any
access-list inside_access_in extended permit tcp any any eq www
access-list inside_access_in extended permit tcp any eq www any
access-list outside_access_in extended permit icmp any any
access-list outside_access_in extended permit tcp any host 177.164.222.138 eq 33
89
access-list outside_access_in extended permit tcp any host 177.164.222.138 eq sm
tp
access-list outside_access_in extended permit tcp any host 177.164.222.138 eq pp
tp
access-list outside_access_in extended permit tcp any host 177.164.222.138 eq ww
w
access-list outside_access_in extended permit tcp any host 177.164.222.138 eq ht
tps
access-list outside_access_in extended permit gre any host 177.164.222.138
access-list outside_access_in extended permit udp any host 177.164.222.138 eq 17
01
access-list outside_access_in extended permit ip any any
access-list inside_access_out extended permit icmp any any
access-list inside_access_out extended permit ip any any
access-list outside_cryptomap extended permit ip 172.29.8.0 255.255.255.0 172.29
.88.0 255.255.255.0
access-list inside_in extended permit icmp any any
access-list inside_in extended permit ip any any
access-list inside_in extended permit udp any any eq isakmp
access-list inside_in extended permit udp any eq isakmp any
access-list inside_in extended permit udp any any
access-list inside_in extended permit tcp any any
pager lines 24
logging enable
logging asdm informational
mtu inside 1500
mtu outside 1500
ip local pool ABC_HQVPN_DHCP 172.29.8.210-172.29.8.230 mask 255.255.255.0
icmp unreachable rate-limit 1 burst-size 1
asdm history enable
arp timeout 14400
nat (inside,outside) source static orange interface service RDP RDP
nat (inside,outside) source static obj_HQ obj_HQ destination static obj_lex obj_
lex route-lookup
nat (inside,outside) source static guava WAN_173_164_222_138 service JT_WWW JT_W
WW
nat (inside,outside) source static guava WAN_173_164_222_138 service JT_HTTPS JT
_HTTPS
nat (inside,outside) source static guava WAN_173_164_222_138 service RDP RDP
nat (inside,outside) source static guava WAN_173_164_222_138 service SMTP SMTP
nat (inside,outside) source static guava WAN_173_164_222_138 service PPTP PPTP
nat (inside,outside) source static guava WAN_173_164_222_138 service L2TP L2TP
object network obj_any
nat (inside,outside) dynamic interface
access-group inside_in in interface inside
access-group outside_access_in in interface outside
route outside 0.0.0.0 0.0.0.0 177.164.222.142 1
route inside 172.29.168.0 255.255.255.0 172.29.8.253 1
timeout xlate 3:00:00
timeout pat-xlate 0:00:30
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
timeout floating-conn 0:00:00
dynamic-access-policy-record DfltAccessPolicy
aaa-server Guava protocol nt
aaa-server Guava (inside) host 172.29.8.3
timeout 15
nt-auth-domain-controller guava
user-identity default-domain LOCAL
http server enable
http 172.29.8.0 255.255.255.0 inside
no snmp-server location
no snmp-server contact
snmp-server enable traps snmp authentication linkup linkdown coldstart warmstart
crypto ipsec ikev1 transform-set ESP-AES-128-SHA esp-aes esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-AES-128-MD5 esp-aes esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-AES-256-SHA esp-aes-256 esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-3DES-SHA esp-3des esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-3DES-MD5 esp-3des esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-DES-SHA esp-des esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-DES-MD5 esp-des esp-md5-hmac
crypto ipsec ikev1 transform-set Remote_VPN_Set esp-3des esp-md5-hmac
crypto ipsec ikev1 transform-set Remote_vpn_set esp-3des esp-md5-hmac
crypto ipsec ikev2 ipsec-proposal AES256
protocol esp encryption aes-256
protocol esp integrity sha-1 md5
crypto ipsec ikev2 ipsec-proposal AES192
protocol esp encryption aes-192
protocol esp integrity sha-1 md5
crypto ipsec ikev2 ipsec-proposal AES
protocol esp encryption aes
protocol esp integrity sha-1 md5
crypto ipsec ikev2 ipsec-proposal 3DES
protocol esp encryption 3des
protocol esp integrity sha-1 md5
crypto ipsec ikev2 ipsec-proposal DES
protocol esp encryption des
protocol esp integrity sha-1 md5
crypto dynamic-map outside_dyn_map 20 set ikev1 transform-set Remote_VPN_Set
crypto dynamic-map outside_dyn_map 20 set reverse-route
crypto map outside_map 1 match address outside_cryptomap
crypto map outside_map 1 set peer 173.190.123.138
crypto map outside_map 1 set ikev1 transform-set ESP-AES-128-SHA ESP-AES-128-MD5
ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA ES
P-3DES-MD5 ESP-DES-SHA ESP-DES-MD5
crypto map outside_map 1 set ikev2 ipsec-proposal AES256 AES192 AES 3DES DES
crypto map outside_map 65535 ipsec-isakmp dynamic outside_dyn_map
crypto map outside_map interface outside
crypto ikev2 policy 1
encryption aes-256
integrity sha
group 5 2
prf sha
lifetime seconds 86400
crypto ikev2 policy 10
encryption aes-192
integrity sha
group 5 2
prf sha
lifetime seconds 86400
crypto ikev2 policy 20
encryption aes
integrity sha
group 5 2
prf sha
lifetime seconds 86400
crypto ikev2 policy 30
encryption 3des
integrity sha
group 5 2
prf sha
lifetime seconds 86400
crypto ikev2 policy 40
encryption des
integrity sha
group 5 2
prf sha
lifetime seconds 86400
crypto ikev2 enable outside
crypto ikev1 enable outside
crypto ikev1 policy 1
authentication pre-share
encryption 3des
hash sha
group 2
lifetime 43200
crypto ikev1 policy 10
authentication crack
encryption aes-256
hash sha
group 2
lifetime 86400
crypto ikev1 policy 20
authentication rsa-sig
encryption aes-256
hash sha
group 2
lifetime 86400
crypto ikev1 policy 30
authentication pre-share
encryption aes-256
hash sha
group 2
lifetime 86400
crypto ikev1 policy 40
authentication crack
encryption aes-192
hash sha
group 2
lifetime 86400
crypto ikev1 policy 50
authentication rsa-sig
encryption aes-192
hash sha
group 2
lifetime 86400
crypto ikev1 policy 60
authentication pre-share
encryption aes-192
hash sha
group 2
lifetime 86400
crypto ikev1 policy 70
authentication crack
encryption aes
hash sha
group 2
lifetime 86400
crypto ikev1 policy 80
authentication rsa-sig
encryption aes
hash sha
group 2
lifetime 86400
crypto ikev1 policy 90
authentication pre-share
encryption aes
hash sha
group 2
lifetime 86400
crypto ikev1 policy 100
authentication crack
encryption 3des
hash sha
group 2
lifetime 86400
crypto ikev1 policy 110
authentication rsa-sig
encryption 3des
hash sha
group 2
lifetime 86400
crypto ikev1 policy 120
authentication pre-share
encryption 3des
hash sha
group 2
lifetime 86400
crypto ikev1 policy 130
authentication crack
encryption des
hash sha
group 2
lifetime 86400
crypto ikev1 policy 140
authentication rsa-sig
encryption des
hash sha
group 2
lifetime 86400
crypto ikev1 policy 150
authentication pre-share
encryption des
hash sha
group 2
lifetime 86400
telnet 192.168.1.0 255.255.255.0 inside
telnet 172.29.8.0 255.255.255.0 inside
telnet timeout 5
ssh timeout 5
console timeout 0
dhcpd auto_config outside vpnclient-wins-override
dhcprelay server 172.29.8.3 inside
threat-detection basic-threat
threat-detection statistics access-list
no threat-detection statistics tcp-intercept
webvpn
enable outside
group-policy ABCtech_VPN internal
group-policy ABCtech_VPN attributes
dns-server value 172.29.8.3
vpn-tunnel-protocol ikev1
split-tunnel-policy tunnelspecified
split-tunnel-network-list value VPN_Tunnel_User
default-domain value ABCtech.local
group-policy GroupPolicy_10.8.8.1 internal
group-policy GroupPolicy_10.8.8.1 attributes
vpn-tunnel-protocol ikev1 ikev2
username who password eicyrfJBrqOaxQvS encrypted
tunnel-group 10.8.8.1 type ipsec-l2l
tunnel-group 10.8.8.1 general-attributes
default-group-policy GroupPolicy_10.8.8.1
tunnel-group 10.8.8.1 ipsec-attributes
ikev1 pre-shared-key *****
ikev2 remote-authentication pre-shared-key *****
ikev2 remote-authentication certificate
ikev2 local-authentication pre-shared-key *****
tunnel-group ABCtech type remote-access
tunnel-group ABCtech general-attributes
address-pool ABC_HQVPN_DHCP
authentication-server-group Guava
default-group-policy ABCtech_VPN
tunnel-group ABCtech ipsec-attributes
ikev1 pre-shared-key *****
tunnel-group 173.190.123.138 type ipsec-l2l
tunnel-group 173.190.123.138 general-attributes
default-group-policy GroupPolicy_10.8.8.1
tunnel-group 173.190.123.138 ipsec-attributes
ikev1 pre-shared-key *****
ikev2 remote-authentication pre-shared-key *****
ikev2 remote-authentication certificate
ikev2 local-authentication pre-shared-key *****
class-map inspection_default
match default-inspection-traffic
policy-map global_policy
class inspection_default
inspect pptp
inspect ftp
inspect netbios
smtp-server 172.29.8.3
prompt hostname context
no call-home reporting anonymous
Cryptochecksum:6a26676668b742900360f924b4bc80de
: end

Hello Wayne,
Can you use a different subnet range than the internal interface, this could cause you a LOT of issues and hours on troubleshooting, so use a dedicated different Ip address range...
I can see that the local Pool range is included into the inside interface Ip address subnet range, change that and the related config ( NAT,etc, ) and let us know what happens,
Regards,
Julio
Security Trainer

Cannot ping RRAS Client from RRAS server.

I have recently created an RRAS pptp connection for an outside network. The RRAS client connects fine and can ping the RRAS server and every device on the RRAS servers local network. The RRAS server cannot ping the remote pptp client nor can any device on
the RRAS servers local network. RRAS is configured to be within the same subnet as the RRAS servers local network. On connection it pulls from a static IP pool.
Any help is truly appreciated

The server is behind a nat device and for testing purposes i have disabled the firewall on both devices. Also I am having an issue where the pptp connection just stops accepting and sending data to the rras server but if you look at the active connections
the client never disconnects. I have attached ipconfig information
CLIENT
Windows IP Configuration
   Host Name . . . . . . . . . . . . : Fellows-PC
   Primary Dns Suffix . . . . . . . :
   Node Type . . . . . . . . . . . . : Hybrid
   IP Routing Enabled. . . . . . . . : No
   WINS Proxy Enabled. . . . . . . . : No
PPP adapter Welsh:
   Connection-specific DNS Suffix . :
   Description . . . . . . . . . . . : Welsh
   Physical Address. . . . . . . . . :
   DHCP Enabled. . . . . . . . . . . : No
   Autoconfiguration Enabled . . . . : Yes
   IPv4 Address. . . . . . . . . . . : 172.16.128.66(Preferred)
   Subnet Mask . . . . . . . . . . . : 255.255.255.255
   Default Gateway . . . . . . . . . :
   NetBIOS over Tcpip. . . . . . . . : Enabled
Ethernet adapter Local Area Connection:
   Connection-specific DNS Suffix . :
   Description . . . . . . . . . . . : Realtek PCIe GBE Family Controller
   Physical Address. . . . . . . . . : BC-5F-F4-75-C5-AD
   DHCP Enabled. . . . . . . . . . . : Yes
   Autoconfiguration Enabled . . . . : Yes
   Link-local IPv6 Address . . . . . : fe80::5418:aba9:4af2:1e12%11(Preferred)
   IPv4 Address. . . . . . . . . . . : 192.168.1.2(Preferred)
   Subnet Mask . . . . . . . . . . . : 255.255.255.0
   Lease Obtained. . . . . . . . . . : Wednesday, March 26, 2014 8:35:58 AM
   Lease Expires . . . . . . . . . . : Saturday, March 29, 2014 8:35:58 AM
   Default Gateway . . . . . . . . . : 192.168.1.1
   DHCP Server . . . . . . . . . . . : 192.168.1.1
   DHCPv6 IAID . . . . . . . . . . . : 247226356
   DHCPv6 Client DUID. . . . . . . . : 00-01-00-01-18-C3-16-85-BC-5F-F4-75-C5-AD
   DNS Servers . . . . . . . . . . . : 75.75.75.75
                                       75.75.76.76
   NetBIOS over Tcpip. . . . . . . . : Enabled
Tunnel adapter isatap.{DF8CAC0D-588D-495A-9185-78C9992DC12F}:
   Media State . . . . . . . . . . . : Media disconnected
   Connection-specific DNS Suffix . :
   Description . . . . . . . . . . . : Microsoft ISATAP Adapter
   Physical Address. . . . . . . . . : 00-00-00-00-00-00-00-E0
   DHCP Enabled. . . . . . . . . . . : No
   Autoconfiguration Enabled . . . . : Yes
Tunnel adapter Teredo Tunneling Pseudo-Interface:
   Connection-specific DNS Suffix . :
   Description . . . . . . . . . . . : Teredo Tunneling Pseudo-Interface
   Physical Address. . . . . . . . . : 00-00-00-00-00-00-00-E0
   DHCP Enabled. . . . . . . . . . . : No
   Autoconfiguration Enabled . . . . : Yes
   IPv6 Address. . . . . . . . . . . : 2001:0:9d38:6abd:1c88:1312:b8c2:97a9(Pref
erred)
   Link-local IPv6 Address . . . . . : fe80::1c88:1312:b8c2:97a9%12(Preferred)
   Default Gateway . . . . . . . . . : ::
   NetBIOS over Tcpip. . . . . . . . : Disabled
Tunnel adapter isatap.{D8973397-8880-4110-A7F9-4D1F6A1C2E8C}:
   Media State . . . . . . . . . . . : Media disconnected
   Connection-specific DNS Suffix . :
   Description . . . . . . . . . . . : Microsoft ISATAP Adapter #2
   Physical Address. . . . . . . . . : 00-00-00-00-00-00-00-E0
   DHCP Enabled. . . . . . . . . . . : No
   Autoconfiguration Enabled . . . . : Yes
SERVER
Windows IP Configuration
   Host Name . . . . . . . . . . . . : IMS
   Primary Dns Suffix . . . . . . . :
   Node Type . . . . . . . . . . . . : Unknown
   IP Routing Enabled. . . . . . . . : Yes
   WINS Proxy Enabled. . . . . . . . : Yes
PPP adapter RAS Server (Dial In) Interface:
   Connection-specific DNS Suffix . :
   Description . . . . . . . . . . . : WAN (PPP/SLIP) Interface
   Physical Address. . . . . . . . . : 00-53-45-00-00-00
   DHCP Enabled. . . . . . . . . . . : No
   IP Address. . . . . . . . . . . . : 172.16.128.65
   Subnet Mask . . . . . . . . . . . : 255.255.255.255
   Default Gateway . . . . . . . . . :
Ethernet adapter Local Area Connection:
   Media State . . . . . . . . . . . : Media disconnected
   Description . . . . . . . . . . . : Broadcom BCM5709C NetXtreme II GigE (NDIS
VBD Client)
   Physical Address. . . . . . . . . : 00-10-18-8D-BC-42
Ethernet adapter Local Area Connection 2:
   Media State . . . . . . . . . . . : Media disconnected
   Description . . . . . . . . . . . : Broadcom BCM5709C NetXtreme II GigE (NDIS
VBD Client) #2
   Physical Address. . . . . . . . . : 00-10-18-8D-BC-40
Ethernet adapter Local Area Connection 4:
   Media State . . . . . . . . . . . : Media disconnected
   Description . . . . . . . . . . . : Broadcom BCM5716C NetXtreme II GigE (NDIS
VBD Client)
   Physical Address. . . . . . . . . : 84-2B-2B-68-6A-FA
Ethernet adapter Local Area Connection 3:
   Connection-specific DNS Suffix . :
   Description . . . . . . . . . . . : Broadcom BCM5716C NetXtreme II GigE (NDIS
VBD Client) #2
   Physical Address. . . . . . . . . : 84-2B-2B-68-6A-F9
   DHCP Enabled. . . . . . . . . . . : No
   IP Address. . . . . . . . . . . . : 172.16.128.1
   Subnet Mask . . . . . . . . . . . : 255.255.255.0
   Default Gateway . . . . . . . . . : 172.16.128.254
   DNS Servers . . . . . . . . . . . : 172.16.128.254
                                       75.75.75.75
   NetBIOS over Tcpip. . . . . . . . : Disabled

Cannot ping windows 2008 r2 while it is possible for another machine in the same network

Hi,
Recently I have set up a new server with windows 2008 r2 enterprise OS which is a domain member server.
At network layer I have two networks one with 192.168.1.0/22 and another with 10.0.0.0/24 network IDs.
My problem is that I cannot ping the newly installed server from a specific machine. Server's IP address is 192.168.1.56 and the specific machine's IP address is 10.0.0.12 and it is a windows XP machine. Of course I have to say that this problem belongs
only to this WinXP machine and all the layer 3 issues are tested and correct. This issue happens while at the same time I can ping domain controller which also is a windows 2008 r2 enterprise box and its IP address is 192.168.1.53. It turns more complicated
when I learned I can ping the winxp machine and connect to it from new server through remote desktop. Firewall also is not the obstacle because I turned it off completely.
Can anybody help me fix the problem?
TIA
Bijan

Hi,
Check the path ping from xp machine to server its timing out after reaching 192.168.1.254 , What kind of a device is 192.168.1.254 IP belongs to.
Tracing
route to sp45newfs.ph45.local [192.168.1.56]
over
a maximum of 30 hops:
0 B15-333.PH45.LOCAL [10.0.0.12]
1 192.168.1.254
2 * * *
Computing
statistics for 50 seconds...
Source to Here This Node/Link
Hop
RTT Lost/Sent = Pct Lost/Sent = Pct Address
0 B15-333.PH45.LOCAL [10.0.0.12]
0/ 100 = 0% |
1 0ms 0/ 100 = 0% 0/ 100 = 0% (192.168.1.254)----------(Which device has this IP)
100/ 100 =100% |
2 --- (100/ 100 =100% )---(100% loss) 0/ 100 = 0% B15-333.PH45.LOCAL [0.0.0.0]
Trace
complete.
Regards,
Srivishnu.K

Cannot Ping IP available to PC on same network

I cannot ping/access an IP address that I can ping/access on a PC using the same WiFi connection.
Any idea on what may be causing this?

GuRoo wrote:
I do not have a firewall turned on at all.
Hi Pete, welcome to the club! I'm no IT expert, but if your Windows PC and Macs are both using the same LAN, I can't see this having anything to do with a firewall. I have a similar issue on my home LAN, though I recently made a change in my router settings which may resolve it if I work on it again. (I have an HP Laserjet plugged into the same router as my Mac Mini G4... I couldn't get my wife's Wintel notebook to find it when I tried before, while it had been only too simple via the Mac, so my LAN issue is really just the opposite of yours).
GuRoo wrote:
This is the first thing ever to make me question my switch to Mac and it's one that has me about to throw it out the window and go back to buggy (but fixable) Windows.
LOL ... If you give us your address, I'm sure there'll be someone there to catch it! Seriously, though, I'm sure you'll have a solution shortly if your start your own thread on this issue. From my interpretation of the original poster's issue, I think this thread has to do with accessing a particular remote IP, a problem I'm also trying to resolve.
best of luck,
Lowell

IPV6 clients cannot ping each other while getting IP from DHCP server running in windows 2008

I have two windows 7 clients and a windows 2008 server connected to a switch with static IP 172:16:5::1/64.
DHCP server is configured with static IP 172:16:5::20/64
when i statically assign IP to windows 7 clients like 172:16:5::21 & ::22, they can ping each other. if they get ip from DHCP server, they cannot ping each other.
if i configure the gateway (172:16:5::1) in the clients manually, they can ping each other.
is there any way we can make dhcp server to give gateway to the clients along with IP?

From what I have gathered:
IPv6 won't route because the DHCP server is setup in 'stateless' mode and the switches do not support IPv6. (
"But if your routers are not IPv6 supported (yet), you can
reconfigure DHCPv6 to Disable Stateless mode, and that'll issue IPv6 addresses that
will eliminate the Ping problem." -
http://www.networkworld.com/article/2228461/microsoft-subnet/setting-up-dhcpv6-to-dynamically-issue-ipv6-addresses-in-a-network.html)
So you must change to 'disable stateless' mode. Which the only way I can THINK to do this is to uninstall DHCP and reinstall DHCP and select 'disable stateless' during the installation (which I haven't confirmed). (In
case, “Disable DHCPv6 stateless mode for this server” option was selected duringrole installation" -
http://blogs.technet.com/b/teamdhcp/archive/2009/03/03/dhcpv6-understanding-of-address-configuration-in-automatic-mode-and-installation-of-dhcpv6-server.aspx)
zz.. but my understanding of DHCP is fragmented, please take what I find with a grain of salt. I am off to reinstall DHCP :] .. fun.
Mediocre Access 2010 | (Baby) Beginner C Sharp | OK at Active Directory (2012) | Fragmented understanding of DNS/DHCP | Laughable experience with Group Policy | Expert question asker on MSDN Forums

2851 router vpn to 851 router lan clients cannot ping

Greets - I'm expanding my lab experience by adding a 2851 router to my mix of 18xx and 851/871 units. Some of this infrastructure is in production, some just lab work. I have established good connectivity between 18xx's and 851/871's with IPSEC VPNs (site-to-site static and dynamic), but my problem is with adding in a 2851.
Setup: 2851 with 12.4 ADVENTK9, WAN on GE0/0 as 216.189.223.bbb/26, LAN on GE0/1 as 172.20.0.1/20 (VPN module, but no additional HWIC modules)
851 with 12.4 ADVENTK9, WAN on FE4 as 216.53.254.aaa/24, LAN on FE0..3 via BVI1 as 172.21.1.1/24
The two router WAN ports are bridged via a 3rd router (a Zywall with 216.0.0.0/8 route, with the router at 216.1.1.1) affectionately called the "InterNOT", which provides a surrogate to the great web, minus actual other hosts and dns, but it doesn't matter. As both my WAN addresses are within 216.x.x.x, this works quite well. This surrogate has tested fine and is known to not be part of a problem.
The 851 has been tested against another 851 with complementary setup and a successful VPN can run between the two.
I have good LAN-WAN connections on each router. I do have a "Good" VPN connection between the two routers.
The problem: I cannot ping from a LAN host on 172.20.x.x on the 2851 to any 172.21.1.x (eg 172.21.1.1) host on the 851, and vice versa.
From a LAN host, I can ping to my InterNOT - for example a dhcp host 172.20.6.2 on the 2851 LAN can ping 216.1.1.1 fine. I can also ping the 851's WAN address at 216.53.254.aaa.
To complicate matters, if I connect to the routers via console, I CAN ping across the vpn to the destination LAN hosts, in both directions.
This seems to indicate that there is a bridging problem between the LAN interfaces to the VPN interfaces. I suspect this is a config problem on the 2851, as I have had a similar config working on my 851 to 851 site-to-site setups. I also suspect it is in the 2851's config as I'm still just starting out with this particular router.
So some stripped-down configs:
For the 2851:
no service config
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
hostname router2851
boot-start-marker
boot-end-marker
no logging buffered
no logging console
enable password mypassword2
no aaa new-model
dot11 syslog
no ip cef
no ip dhcp use vrf connected
ip dhcp excluded-address 172.20.0.1 172.20.6.1
ip dhcp excluded-address 172.20.6.254 172.20.15.254
ip dhcp pool Internal_2000
   import all
   network 172.20.0.0 255.255.240.0
   domain-name myseconddomain.int
   default-router 172.20.0.1
   lease 7
no ip domain lookup
multilink bundle-name authenticated
voice-card 0
no dspfarm
crypto pki <<truncated>>
crypto pki certificate chain TP-self-signed-2995823027
<<truncated>>
   quit
username myusername privilege 15 password 0 mypassword2
archive
log config
hidekeys
crypto isakmp policy 1
encr 3des
authentication pre-share
group 2
crypto isakmp key mysharedkey address 216.53.254.aaa
crypto ipsec transform-set ESP-3DES-SHA esp-3des esp-sha-hmac
crypto map SDM_CMAP_1 1 ipsec-isakmp
description Tunnel to216.53.254.aaa
set peer 216.53.254.aaa
set transform-set ESP-3DES-SHA
match address 100
interface GigabitEthernet0/0
description $ETH-WAN$
ip address 216.189.223.bbb 255.255.255.192
ip nat outside
ip virtual-reassembly
duplex auto
speed auto
crypto map SDM_CMAP_1
no shut
interface GigabitEthernet0/1
description $FW_INSIDE$$ETH-LAN$
ip address 172.20.0.1 255.255.240.0
ip nat inside
ip virtual-reassembly
no ip route-cache
duplex auto
speed auto
no mop enabled
ip forward-protocol nd
ip route 0.0.0.0 0.0.0.0 GigabitEthernet0/0
ip http server
ip http authentication local
ip http secure-server
ip dns server
ip nat inside source route-map SDM_RMAP_1 interface GigabitEthernet0/0 overload
access-list 1 remark CCP_ACL Category=2
access-list 1 permit 172.20.0.0 0.0.15.255
access-list 100 remark CCP_ACL Category=4
access-list 100 remark IPSec Rule
access-list 100 permit ip 172.20.0.0 0.0.15.255 172.21.1.0 0.0.0.255
access-list 101 remark CCP_ACL Category=2
access-list 101 remark IPSec Rule
access-list 101 deny   ip 172.20.0.0 0.0.15.255 172.21.1.0 0.0.0.255
access-list 101 permit ip 172.20.0.0 0.0.15.255 any
route-map SDM_RMAP_1 permit 1
match ip address 101
control-plane
banner motd ~This is a private computer system for authorized use only. And Stuff~
line con 0
line aux 0
line vty 0 4
privilege level 15
password mypassword
login local
transport input telnet ssh
scheduler allocate 20000 1000
end
And for the 851:
no service pad
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
hostname router851
boot-start-marker
boot-end-marker
logging buffered 52000 debugging
no logging console
enable password mypassword
aaa new-model
aaa authentication login default local
aaa authorization exec default local
aaa session-id common
resource policy
clock timezone PCTime -5
clock summer-time PCTime date Apr 6 2003 2:00 Oct 26 2003 2:00
no ip dhcp use vrf connected
ip dhcp excluded-address 172.21.1.1 172.21.1.100
ip dhcp pool Internal_2101
   import all
   network 172.21.1.0 255.255.255.0
   default-router 172.21.1.1
   domain-name mydomain.int
   dns-server 172.21.1.10
   lease 4
ip cef
ip domain name mydomain.int
ip name-server 172.21.1.10
crypto pki <<truncated>>
crypto pki certificate chain TP-self-signed-3077836316
<<truncated>>
quit
username myusername privilege 15 password 0 mypassword2
crypto isakmp policy 1
encr 3des
authentication pre-share
group 2
crypto isakmp key mysharedkey address 216.189.223.aaa
crypto ipsec transform-set ESP-3DES-SHA esp-3des esp-sha-hmac
crypto ipsec transform-set ESP-3DES-SHA1 esp-3des esp-sha-hmac
crypto ipsec transform-set ESP-3DES-SHA2 esp-3des esp-sha-hmac
crypto map SDM_CMAP_1 1 ipsec-isakmp
description Tunnel to216.189.223.bbb
set peer 216.189.223.bbb
set transform-set ESP-3DES-SHA2
match address 100
bridge irb
interface FastEthernet0
spanning-tree portfast
interface FastEthernet1
spanning-tree portfast
interface FastEthernet2
spanning-tree portfast
interface FastEthernet3
spanning-tree portfast
interface FastEthernet4
description $ETH-WAN$
ip address 216.53.254.aaa 255.255.254.0
ip nat outside
ip virtual-reassembly
ip tcp adjust-mss 1460
duplex auto
speed auto
no cdp enable
crypto map SDM_CMAP_1
no shut
interface Vlan1
description Internal Network
no ip address
ip nat inside
ip virtual-reassembly
bridge-group 1
bridge-group 1 spanning-disabled
interface BVI1
description Bridge to Internal Network
ip address 172.21.1.1 255.255.255.0
ip nat inside
ip virtual-reassembly
ip route 0.0.0.0 0.0.0.0 FastEthernet4
ip route 172.21.1.0 255.255.255.0 BVI1
ip http server
ip http secure-server
ip nat inside source route-map SDM_RMAP_1 interface FastEthernet4 overload
access-list 1 remark CCP_ACL Category=2
access-list 1 permit 172.21.1.0 0.0.0.255
access-list 100 remark CCP_ACL Category=4
access-list 100 remark IPSec Rule
access-list 100 permit ip 172.21.1.0 0.0.0.255 172.20.0.0 0.0.15.255
access-list 101 remark CCP_ACL Category=2
access-list 101 remark IPSec Rule
access-list 101 deny   ip 172.21.1.0 0.0.0.255 172.20.0.0 0.0.15.255
access-list 101 remark IPSec Rule
access-list 101 deny   ip 172.21.1.0 0.0.0.255 172.21.101.0 0.0.0.31
access-list 101 permit ip 172.21.1.0 0.0.0.255 any
route-map SDM_RMAP_1 permit 1
match ip address 101
control-plane
bridge 1 route ip
banner motd ~This is a private computer system for authorized use only. And Stuff.~
line con 0
password mypassword
no modem enable
line aux 0
line vty 0 4
password mypassword
scheduler max-task-time 5000
end
Note that the above are somewhat stripped-down configs, without firewall or WAN ACL's - interestingly my default WAN-Inbound ACLs seem to break connectivity when included, so I realize I have some more cleanup to do there, but the 2851 LAN bridging seems to be what I should concentrate on first.
I'm still googling some of the particulars with the 2851, but any assistance is appreciated.
Regards,
Ted.

Hi,
First,please delete NAT.If we configured the NAT in the RRAS,the source IP address in all packets sent to 192.168.1.0/24 would be translated to 192.168.1.224.
Second,please enable the LAN routing in RRAS server.To enable LAN routing,please follow the steps below,
1.In the RRAS server,Open Routing and Remote Access.
2.Right-click the server name,then click
properties.
3.On the General tab,select
IPv4 Router check box,and then click Local area network(LAN) routing only.
Then,announce the 172.16.0.0 network to the router.
To learn more details about enabling LAN routing, please refer to the link below,
http://technet.microsoft.com/en-us/library/dd458974.aspx
Best Regards,
Tina

Clients cannot ping the default gateway when connected to SSID

Here is my environment,
My controller is vWLC installed in ESXi which has to vNet Cards configured with all vlans(4095), then it is connected to a 3560 switch with trunk. The configuration of the switch interface is as belows:
LS3560CG#sh run int fa0/1
Building configuration...
Current configuration : 138 bytes
interface FastEthernet0/1
description To_WLC
switchport trunk encapsulation dot1q
switchport mode trunk
spanning-tree portfast
end
The IP of management interface of WLC is 10.10.10.90, VLAN is 10, DHCP primary is 10.10.10.1 which is in the 3560, the DHCP pool is configured as blows:
LS3560CG#sh run int fa0/1
Building configuration...
Current configuration : 138 bytes
interface FastEthernet0/1
description To_WLC
switchport trunk encapsulation dot1q
switchport mode trunk
spanning-tree portfast
end
The SSID is BYOD and I can connect the SSID and get the IP address such as 10.10.10.118/24, but for now, i cannot ping 10.10.10.1, but i can ping 10.10.10.90:
Can anyone help me with this? Thanks

Hi Scott
Correct! I have resolved this a few minutes earlier. I have assigned the vSwitch to Promiscuous Mode but forgot to switch it to "Accept", the default value is "Reject"
Thanks so much!

1602i standalone AP cannot ping RADIUS server

I have a new 1602i standalone AP trying to use RADIUS authentication. For some reason the 1602 cannot ping the RADIUS server, but will get a response from other devices. Both are on the same subnet, the new one at .213 and the RADIUS at .209.
AP6#ping xxx.xx.120.209
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to xxx.xx..120.209, timeout is 2 seconds:
Success rate is 0 percent (0/5)
AP6#ping xxx.xx.120.217
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to xxx.xx..120.217, timeout is 2 seconds:
Success rate is 100 percent (5/5), round-trip min/avg/max = 1/3/4 ms
The RADUIS server is able to ping the new AP successfully.
AP1#ping xxx.xx.120.213
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to xxx.xx.120.213, timeout is 2 seconds:
Success rate is 100 percent (5/5), round-trip min/avg/max = 2/2/3 ms
Any thoughts to why that AP is unable to ping that one particular client? Other APs are successfully contacting it for RADIUS authentication.

version 15.2
no service pad
service timestamps debug datetime msec
service timestamps log datetime msec
service password-encryption
hostname AP6
logging rate-limit console 9
enable secret 5 xxxxxxxxxxxx
aaa new-model
aaa group server radius rad_eap
server xxx.xx.120.209 auth-port 1812 acct-port 1813
aaa group server radius rad_mac
aaa group server radius rad_acct
aaa group server radius rad_admin
aaa group server tacacs+ tac_admin
aaa group server radius rad_pmip
aaa group server radius dummy
aaa authentication login eap_methods group rad_eap
aaa authentication login mac_methods local
aaa authorization exec default local
aaa accounting network acct_methods start-stop group rad_acct
aaa session-id common
clock timezone -0500 -5 0
clock summer-time -0400 recurring
no ip routing
no ip cef
dot11 syslog
dot11 ssid xxx.xx
   authentication open eap eap_methods
   authentication network-eap eap_methods
   authentication key-management wpa
crypto pki token default removal timeout 0
username Cisco privilege 15 password 7 xxxxx
bridge irb
interface Dot11Radio0
no ip address
no ip route-cache
encryption mode ciphers tkip
ssid MANH
antenna gain 0
stbc
beamform ofdm
station-role root
bridge-group 1
bridge-group 1 subscriber-loop-control
bridge-group 1 spanning-disabled
bridge-group 1 block-unknown-source
no bridge-group 1 source-learning
no bridge-group 1 unicast-flooding
interface Dot11Radio1
no ip address
no ip route-cache
shutdown
antenna gain 0
dfs band 3 block
channel dfs
station-role root
bridge-group 1
bridge-group 1 subscriber-loop-control
bridge-group 1 spanning-disabled
bridge-group 1 block-unknown-source
no bridge-group 1 source-learning
no bridge-group 1 unicast-flooding
interface GigabitEthernet0
no ip address
no ip route-cache
duplex auto
speed auto
bridge-group 1
bridge-group 1 spanning-disabled
no bridge-group 1 source-learning
interface BVI1
ip address dhcp client-id GigabitEthernet0
no ip route-cache
ip forward-protocol nd
ip http server
no ip http secure-server
ip http help-path http://www.cisco.com/warp/public/779/smbiz/prodconfig/help/eag
ip radius source-interface BVI1
snmp-server view dot11view ieee802dot11 included
snmp-server community RW
snmp-server chassis-id AP6
snmp-server enable traps snmp authentication linkdown linkup coldstart warmstart
snmp-server enable traps tty
snmp-server enable traps entity
snmp-server enable traps disassociate
snmp-server enable traps deauthenticate
snmp-server enable traps authenticate-fail
snmp-server enable traps dot11-qos
snmp-server enable traps switch-over
snmp-server enable traps rogue-ap
snmp-server enable traps wlan-wep
snmp-server enable traps config-copy
snmp-server enable traps config
snmp-server enable traps syslog
snmp-server enable traps cpu threshold
snmp-server enable traps aaa_server
snmp-server host .0.39 public
radius-server local
user user1 nthash 7
radius-server attribute 32 include-in-access-req format %h
radius-server host xxx.xx.120.209 auth-port 1812 acct-port 1813 key 7
radius-server vsa send accounting
bridge 1 route ip
line con 0
line vty 0 4
transport input all
sntp server xxx.xx.0.11
sntp broadcast client
end

Anyconnect VPN peers cannot ping, RDP each other

I have an ASA5505 running ASA 8.3(1) and ASDM 7.1(1). I have a remote access VPN set up and the remote access users are able to log in and access LAN resources.   I can ping the VPN peers from the remote LAN.    My problem that the VPN peers cannot ping (RDP, ectc..) each other.   Pinging one VPN peer from another reveals the following error in the ASA Log.
Asymmetric NAT rules matched for forward and reverse flows; Connection for icmp src outside:10.10.10.8 dst outside:10.10.10.9 (type 8, code 0) denied due to NAT reverse path failure.
Below is my ASA running-config:
ASA Version 8.3(1)
hostname ciscoasa
domain-name dental.local
enable password 9ddwXcOYB3k84G8Q encrypted
passwd 2KFQnbNIdI.2KYOU encrypted
names
interface Vlan1
nameif inside
security-level 100
ip address 192.168.1.1 255.255.255.0
interface Vlan2
nameif outside
security-level 0
ip address dhcp setroute
interface Ethernet0/0
switchport access vlan 2
interface Ethernet0/1
interface Ethernet0/2
interface Ethernet0/3
interface Ethernet0/4
interface Ethernet0/5
interface Ethernet0/6
interface Ethernet0/7
ftp mode passive
clock timezone CST -6
clock summer-time CDT recurring
dns domain-lookup inside
dns server-group DefaultDNS
name-server 192.168.1.128
domain-name dental.local
same-security-traffic permit inter-interface
same-security-traffic permit intra-interface
object network obj_any
subnet 0.0.0.0 0.0.0.0
object network RAVPN
subnet 10.10.10.0 255.255.255.0
object network NETWORK_OBJ_10.10.10.0_28
subnet 10.10.10.0 255.255.255.240
object network NETWORK_OBJ_192.168.1.0_24
subnet 192.168.1.0 255.255.255.0
access-list Local_LAN_Access remark VPN client local LAN access
access-list Local_LAN_Access standard permit host 0.0.0.0
access-list DefaultRAGroup_splitTunnelAcl standard permit 192.168.1.0 255.255.255.0
access-list VpnPeers remark allow vpn peers to ping each other
access-list VpnPeers extended permit ip object NETWORK_OBJ_10.10.10.0_28 object NETWORK_OBJ_10.10.10.0_28
pager lines 24
logging enable
logging asdm informational
logging mail informational
logging from-address [email protected]
logging recipient-address [email protected] level informational
logging rate-limit 1 600 level 6
mtu outside 1500
mtu inside 1500
ip local pool VPNPool 10.10.10.5-10.10.10.10 mask 255.255.255.0
icmp unreachable rate-limit 1 burst-size 1
asdm image disk0:/asdm-711.bin
no asdm history enable
arp timeout 14400
nat (inside,any) source static any any destination static RAVPN RAVPN
nat (inside,outside) source static NETWORK_OBJ_192.168.1.0_24 NETWORK_OBJ_192.168.1.0_24 destination static NETWORK_OBJ_10.10.10.0_28 NETWORK_OBJ_10.10.10.0_28
nat (inside,outside) source static any any destination static NETWORK_OBJ_10.10.10.0_28 NETWORK_OBJ_10.10.10.0_28
object network obj_any
nat (inside,outside) dynamic interface
object network RAVPN
nat (any,outside) dynamic interface
timeout xlate 3:00:00
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
dynamic-access-policy-record DfltAccessPolicy
http server enable
http 192.168.1.0 255.255.255.0 inside
no snmp-server location
no snmp-server contact
snmp-server community *****
snmp-server enable traps snmp authentication linkup linkdown coldstart
crypto ipsec transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
crypto ipsec transform-set ESP-DES-SHA esp-des esp-sha-hmac
crypto ipsec transform-set ESP-3DES-SHA esp-3des esp-sha-hmac
crypto ipsec transform-set ESP-DES-MD5 esp-des esp-md5-hmac
crypto ipsec transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
crypto ipsec transform-set ESP-3DES-MD5 esp-3des esp-md5-hmac
crypto ipsec transform-set ESP-AES-256-SHA esp-aes-256 esp-sha-hmac
crypto ipsec transform-set ESP-AES-128-SHA esp-aes esp-sha-hmac
crypto ipsec transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
crypto ipsec transform-set ESP-AES-128-MD5 esp-aes esp-md5-hmac
crypto ipsec transform-set ESP-AES-128-SHA-TRANS esp-aes esp-sha-hmac
crypto ipsec transform-set ESP-AES-128-SHA-TRANS mode transport
crypto ipsec transform-set ESP-DES-SHA-TRANS esp-des esp-sha-hmac
crypto ipsec transform-set ESP-DES-SHA-TRANS mode transport
crypto ipsec transform-set ESP-AES-192-SHA-TRANS esp-aes-192 esp-sha-hmac
crypto ipsec transform-set ESP-AES-192-SHA-TRANS mode transport
crypto ipsec transform-set ESP-AES-256-SHA-TRANS esp-aes-256 esp-sha-hmac
crypto ipsec transform-set ESP-AES-256-SHA-TRANS mode transport
crypto ipsec transform-set ESP-3DES-SHA-TRANS esp-3des esp-sha-hmac
crypto ipsec transform-set ESP-3DES-SHA-TRANS mode transport
crypto ipsec security-association lifetime seconds 28800
crypto ipsec security-association lifetime kilobytes 4608000
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set transform-set ESP-AES-128-SHA ESP-AES-192-SHA ESP-AES-256-SHA ESP-3DES-SHA ESP-DES-SHA ESP-AES-128-SHA-TRANS ESP-AES-192-SHA-TRANS ESP-AES-256-SHA-TRANS ESP-3DES-SHA-TRANS ESP-DES-SHA-TRANS
crypto map outside_map 65535 ipsec-isakmp dynamic SYSTEM_DEFAULT_CRYPTO_MAP
crypto map outside_map interface outside
crypto ca trustpoint LOCAL-CA-SERVER
keypair LOCAL-CA-SERVER
crl configure
crypto ca trustpoint ASDM_TrustPoint0
enrollment self
subject-name CN=ciscoasa
keypair billvpnkey
proxy-ldc-issuer
crl configure
crypto ca server
cdp-url http://ciscoasa/+CSCOCA+/asa_ca.crl
issuer-name CN=ciscoasa
smtp from-address admin@ciscoasa
crypto ca certificate chain LOCAL-CA-SERVER
certificate ca 01
   **hidden**
quit
crypto ca certificate chain ASDM_TrustPoint0
certificate 10bdec50
    **hidden**
quit
crypto isakmp enable outside
crypto isakmp policy 10
authentication crack
encryption aes-256
hash sha
group 2
lifetime 86400
crypto isakmp policy 20
authentication rsa-sig
encryption aes-256
hash sha
group 2
lifetime 86400
crypto isakmp policy 30
authentication pre-share
encryption aes-256
hash sha
group 2
lifetime 86400
crypto isakmp policy 40
authentication crack
encryption aes-192
hash sha
group 2
lifetime 86400
crypto isakmp policy 50
authentication rsa-sig
encryption aes-192
hash sha
group 2
lifetime 86400
crypto isakmp policy 60
authentication pre-share
encryption aes-192
hash sha
group 2
lifetime 86400
crypto isakmp policy 70
authentication crack
encryption aes
hash sha
group 2
lifetime 86400
crypto isakmp policy 80
authentication rsa-sig
encryption aes
hash sha
group 2
lifetime 86400
crypto isakmp policy 90
authentication pre-share
encryption aes
hash sha
group 2
lifetime 86400
crypto isakmp policy 100
authentication crack
encryption 3des
hash sha
group 2
lifetime 86400
crypto isakmp policy 110
authentication rsa-sig
encryption 3des
hash sha
group 2
lifetime 86400
crypto isakmp policy 120
authentication pre-share
encryption 3des
hash sha
group 2
lifetime 86400
crypto isakmp policy 130
authentication crack
encryption des
hash sha
group 2
lifetime 86400
crypto isakmp policy 140
authentication rsa-sig
encryption des
hash sha
group 2
lifetime 86400
crypto isakmp policy 150
authentication pre-share
encryption des
hash sha
group 2
lifetime 86400
client-update enable
telnet 192.168.1.1 255.255.255.255 inside
telnet timeout 5
ssh timeout 5
console timeout 0
management-access inside
dhcpd auto_config outside
dhcpd address 192.168.1.50-192.168.1.99 inside
dhcpd enable inside
threat-detection basic-threat
threat-detection statistics
threat-detection statistics tcp-intercept rate-interval 30 burst-rate 400 average-rate 200
ssl trust-point ASDM_TrustPoint0 outside
webvpn
enable outside
svc image disk0:/anyconnect-win-3.1.04072-k9.pkg 1
svc profiles DellStudioClientProfile disk0:/dellstudioclientprofile.xml
svc enable
tunnel-group-list enable
internal-password enable
smart-tunnel list SmartTunnelList RDP mstsc.exe platform windows
group-policy DefaultRAGroup internal
group-policy DefaultRAGroup attributes
dns-server value 192.168.1.128
vpn-tunnel-protocol l2tp-ipsec
split-tunnel-policy tunnelspecified
split-tunnel-network-list value DefaultRAGroup_splitTunnelAcl
default-domain value dental.local
webvpn
svc modules value vpngina
group-policy DefaultRAGroup_1 internal
group-policy DefaultRAGroup_1 attributes
dns-server value 192.168.1.128
vpn-tunnel-protocol l2tp-ipsec
default-domain value dental.local
group-policy DfltGrpPolicy attributes
dns-server value 192.168.1.128
vpn-simultaneous-logins 4
vpn-tunnel-protocol IPSec l2tp-ipsec svc webvpn
group-lock value RAVPN
split-tunnel-network-list value Local_LAN_Access
default-domain value dental.local
webvpn
url-list value DentalMarks
svc modules value vpngina
svc profiles value dellstudio type user
svc ask enable default webvpn
smart-tunnel enable SmartTunnelList
username wketchel1 password 5c5OoeNtCiX6lGih encrypted
username wketchel1 attributes
vpn-group-policy DfltGrpPolicy
webvpn
svc profiles value DellStudioClientProfile type user
username wketchel password 5c5OoeNtCiX6lGih encrypted privilege 15
username wketchel attributes
vpn-group-policy DfltGrpPolicy
webvpn
svc modules none
svc profiles value DellStudioClientProfile type user
username jenniferk password 5.TcqIFN/4yw0Vq1 encrypted privilege 0
username jenniferk attributes
vpn-group-policy DfltGrpPolicy
webvpn
svc profiles value DellStudioClientProfile type user
tunnel-group DefaultRAGroup general-attributes
address-pool VPNPool
authorization-server-group LOCAL
tunnel-group DefaultRAGroup ipsec-attributes
pre-shared-key *****
tunnel-group DefaultRAGroup ppp-attributes
authentication pap
authentication ms-chap-v2
authentication eap-proxy
tunnel-group RAVPN type remote-access
tunnel-group RAVPN general-attributes
address-pool VPNPool
authorization-server-group LOCAL
tunnel-group RAVPN webvpn-attributes
group-alias RAVPN enable
tunnel-group RAVPN ipsec-attributes
pre-shared-key *****
tunnel-group RAVPN ppp-attributes
authentication pap
authentication ms-chap-v2
authentication eap-proxy
tunnel-group WebSSLVPN type remote-access
tunnel-group WebSSLVPN webvpn-attributes
group-alias WebSSLVPN enable
class-map inspection_default
match default-inspection-traffic
policy-map type inspect dns preset_dns_map
parameters
message-length maximum client auto
message-length maximum 512
policy-map global_policy
class inspection_default
inspect dns preset_dns_map
inspect ftp
inspect h323 h225
inspect h323 ras
inspect rsh
inspect rtsp
inspect esmtp
inspect sqlnet
inspect skinny
inspect sunrpc
inspect xdmcp
inspect sip
inspect netbios
inspect tftp
inspect ip-options
service-policy global_policy global
smtp-server 173.194.64.108
prompt hostname context
hpm topN enable
Cryptochecksum:3304bf6dcf6af5804a21e9024da3a6f8
: end

Hi,
Seems to me that you could clean up the current NAT configuration a bit and make it a bit clearer.
I would suggest the following changes
object network VPN-POOL
subnet 10.10.10.0 255.255.255.0
object network LAN
subnet 192.168.1.0 255.255.255.0
object-group network PAT-SOURCE
network-object 192.168.1.0 255.255.255.0
network-object 10.10.10.0 255.255.255.0
nat (inside,outside) source static LAN LAN destination static VPN-POOL VPN-POOL
nat (outside,outside) 1 source static VPN-POOL VPN-POOL destination static VPN-POOL VPN-POOL
nat (any,outside) after-auto source dynamic PAT-SOURCE interface
The above should enable
Dynamic PAT for LAN and VPN users
NAT0 for the traffic between LAN and VPN
NAT0 for traffic between VPN users
You could then remove the previous NAT configurations. Naturally please do backup the configuration before doing the change if you wish to move back to the original configuration.
no nat (inside,any) source static any any destination static RAVPN RAVPN
no nat (inside,outside) source static NETWORK_OBJ_192.168.1.0_24 NETWORK_OBJ_192.168.1.0_24 destination static NETWORK_OBJ_10.10.10.0_28 NETWORK_OBJ_10.10.10.0_28
no nat (inside,outside) source static any any destination static NETWORK_OBJ_10.10.10.0_28 NETWORK_OBJ_10.10.10.0_28
no object network obj_any
no object network RAVPN
In the event that you dont want to change the configurations that much you might be fine just by adding this
object network VPN-POOL
subnet 10.10.10.0 255.255.255.0
nat (outside,outside) 1 source static VPN-POOL VPN-POOL destination static VPN-POOL VPN-POOL
But the other above configurations changes would make the current NAT configurations simpler and clearer to see each "nat" configurations purpose.
- Jouni

Cisco C6500 CSM - Real server cannot ping its VIP.

I've been running into an issue with Cisco CSM for a number of years, but always found a way around it. Im attempting to get to the bottom of this to find out once and for all, if this is infact a limitation of the device, or a config issue/work around is possible.
Here is my situation. My CSM's are configured in bridging mode. Traffic works great, traffic bridges across vlans correctly. Everything works and have many instances of smilar configurations running in production. Every once and a while, a client requests that a "real" server (ie LWCMW-021)
cannot ping its VIP address (10.95.88.68). I am assuming this is related to the NAT Server, but not 100% sure. Clients have requested this functionality for some type of application based purpose, but Im unaware if CSM in bridging mode can provide this or not.
Any suggestions?
real LWCMW-021
address 10.95.88.59
inservice
real LWCMW-022
address 10.95.88.60
inservice
serverfarm LWCMW-80
nat server
no nat client
real name LWCMW-021 80
inservice
real name LWCMW-022 80
inservice
probe HTTP-80 (defined elsewhere)
vserver LWCMW-80
virtual 10.95.88.68 tcp WWW
vlan 120
serverfarm LWCMW-80
persistent rebalance
inservice

Sorry for giving false hope. It is only possible in ACE module. In case of CSM I believe we can only use workaround.
In case of ACE we can bind the Virtual IP to mutliple vlan. In that case we see a ARP entry like this.
10.10.10.111    e0.5f.b9.a1.72.2b vlan345   VSERVER    LOCAL     _         up
10.10.10.111    e0.5f.b9.a1.72.2b vlan346   VSERVER    LOCAL     _         up
As Virtual IP is not bound to a particular vlan in case of CSM it does not work here, but I can say for sure it is expected behavior.
The logic would be that the server tries to resolve the ARP for Virtual IP and it does not get a response.
In my case virtual ip is 10.10.10.111 before applying policy on ACE you can see that it is exhibiting the same behaviour.
Time     | Vmware_b4:72:11                       | 10.0.0.0                              | 10.10.10.4                            |
|         |                   | Broadcast         |                   | 224.0.0.1         |                   | 224.0.0.22        |
|0.000    |         Who has 10.10.10.11           |                   |                   |                   |                   |ARP: Who has 10.10.10.111? Tell 10.10.10.11
|         |(0)      ------------------> (0)      |                   |                   |                   |          |
|0.999    |         Who has 10.10.10.11           |                   |                   |                   |                   |ARP: Who has 10.10.10.111? Tell 10.10.10.11
|         |(0)      ------------------> (0)      |                   |                   |                   |                   |
|         |                   |                   |                   |                   |(0)      ------------------> (0)      |
|1.998    |         Who has 10.10.10.11           |                   |                   |                   |                   |ARP: Who has 10.10.10.111? Tell 10.10.10.11
|         |(0)      ------------------> (0)      |                   |                   |                   |                   |
|3.014    |         Who has 10.10.10.11           |                   |                   |                   |                   |ARP: Who has 10.10.10.111? Tell 10.10.10.11
|         |(0)      ------------------> (0)      |                   |                   |                   |                   |
|4.014    |         Who has 10.10.10.11           |                   |                   |                   |                   |ARP: Who has 10.10.10.111? Tell 10.10.10.11
|         |(0)      ------------------> (0)      |                   |                   |                   |                   |
Hope that helps.

Cannot ping by name

I have one system on my network that cannot ping any workstations or servers by name but can ping by IP Address. I get error Ping request could not find host tt-data. Please check the name and try again.
I tried the following troubleshooting steps but nothing fixed it
-Tried a static ip and dns address
-Added an entry in the host file and tried to ping the server name and it failed as I got same error as above
-Reinstalled network card driver as well as updated it
-Did an ipconfig /flushdns and ipconfig /registerdns
-Stop and Started Browser, Computer and DNS Client services
-Rebooted pc multiple times
-No errors in application or system logs
-Windows firewall service started but all profiles disabled
-Stopped windows firewall
-Cannot ping localhost
-netsh interface ipv4 reset
I am not sure what the issue is as I am stumpped as DNS is clearly not working but I do not understand why the host file entries are not working either when you ping by name but IP Addresses work fine. All other workstations work fine so it has to be something
on this machine.
Any assistance would be greatly appreciated.

Well you might follow the steps on this article to reset TCP/IP on the host, otherwise I am stumped.
http://support.microsoft.com/kb/299357
Use a manual method to reset TCP/IP for Windows Vista and Windows 7
Note This section is intended for advanced computer users. If you are not comfortable with advanced troubleshooting, ask someone for help or contact Support. For information about how to contact Support, see the Microsoft Help and Support contact information
Web site:
http://support.microsoft.com/contactus
The reset command is available in the IP context of the NetShell utility. Follow these steps to use the reset command to reset TCP/IP manually:
To open a command prompt, click Start and then type CMD in the Search programs and files.
Right-click CMD.exe icon in Programs and choose Run as administrator.
When the User Account Control box pop up, click Yes.
At the command prompt, copy and paste (or type) the following command and then press ENTER:
netsh int ip reset c:\resetlog.txt
Note If you do not want to specify a directory path for the log file, use the following command:
netsh int ip reset resetlog.txt
Reboot the computer.
When you run the reset command, it rewrites two registry keys that are used by TCP/IP. This has the same result as removing and reinstalling the protocol. The reset command rewrites the following two registry keys:
SYSTEM\CurrentControlSet\Services\Tcpip\Parameters\
SYSTEM\CurrentControlSet\Services\DHCP\Parameters\
To run the manual command successfully, you must specify a file name for the log, in which the actions that netsh takes will be recorded. When you run the manual command, TCP/IP is reset and the actions that were taken are recorded in the log file, known as
resetlog.txt in this article.
The first example, c:\resetlog.txt, creates a path where the log will reside. The second example, resetlog.txt, creates the log file in the current directory. In either case, if the specified log file already exists, the new log will be appended to the end
of the existing file.

Cannot ping an interface

Hi all,
I have decided to add a separate vlan/wlan to the network. This interface uses port 1 (My management interface uses port 2). I have connected the port to a router, which is connected to a gateway.
I checked and the routing is done correctly. When I connect a pc to the router, I have access to internet. However, when I connect to the wlan that's associated with the vlan on port 1, I not only cannot access internet, but also cannot ping the router.
I can ping the interface when I connect to the wlan. However, I cannot ping the router.
The same thing happens when I connect my pc to the router. I cannot ping the interface as well.
Is there something that I am missing? It seems that there is a connectivity issue in the connection between port 1 and the router. Should I try using a crossover cable and see if it solves my problem?
Thanks!
Tibet

Your diagram is very clear. You have few options here
Option 1
WLC port 1 & Router LAN port onto your switch (rather directly connecting router to WLC). In this way WLC connected switch port should be configured as trunk port & router connected switchport should be configured as access port for the vlan belongs to 10.0.0.0/24 network.
If you are thinking about creating multiple WLANs (in futrue) with your router as LAN gateway, then you should configure router connected switchport as trunkport & subinterface on your router LAN interface.
Option 2
Aggregate WLC port 1-2 into one single port channel & create a single trunk link between WLC & Switch. In this way you will get more bandwith for your user traffic.(usually mgt does not want dedicated 1G link). Then configure Router LAN interface connected switchport as access port (if you only require single WLAN) or trunk port (if you require multiple WLAN)
I prefer option 2 because of its flexibility & scalability. Let us know your choice & then accordingly we can help you to get this done.
Also post your WLC "show sysinfo" as well.
HTH
Rasika
**** Pls rate all useful responses ****

Attempting to install Forms 6.0.5.0.2 (or 6.0.8.8.0) run-time and 8.1.6 client on sam

Attempting to install Forms 6.0.5.0.2 (or 6.0.8.8.0) run-time and 8.1.6 client on same NT box.
1) I attempted to install 8.1.6 client first in c:\oracle\ora81, then Forms 6 in c:\oracle\forms6. The installer (3.3.1.2.4) errors, saying forms 6 does not support a multi-home installation.
2) Attmpted to install Forms 6 first in c:\orant. Then installed 8.1.6 client in c:\oracle\ora81. After beginning installation (application user) the following Dependency message displays and the installation is canceled: "Installation cannot continue for the follwoing reason(s). [Oracle ODBC Driver is a single Oracle home product. It is already installed in location c:\oracle\ora81. Oracle provider for OLE DB is a single oracle home product. It is already installed in location c:\oracle\ora81. Oracle objects for OLE is a .... Pracle Provider for OLE is a single home ... You can either de-install these products or install the products in the same location as the single home products."
Click ok and the installation cancels.
How do I install these two products on the same box?

We had to upgrade from 7.3.2 to 7.3.4 when we moved over to Forms
6.0.5.0.2 and it's working fine.
We are using Net 8 as well.
Finn Ellebaek Nielsen (ChangeGroup ApS) (guest) wrote:
: I have problems with Forms 6.0.5.0.2 running against an Oracle
: 7.3.4 with Net8. When trying to insert or update records I get
: an FRM-40508: ORACLE error: unable to INSERT record/FRM-40509:
: ORACLE error: unable to UPDATE record. The Help | Display Error
: menu item shows statement = "S3AVWU3wo|$6o|" (garbled
: message), error = "ORA-12663: Services required by client not
: available on the server" (sometimes it's "ORA-01403: no data
: found").
: It works fine against 8.0.5. As far as I'm aware Forms 6 is
: certified against 7.3.4?
: Any clues?
: Thanks for your help.
: Finn
null

ASA 5505 8.2 - SSL VPN - Cannot Ping inside host's

Hello All,
I'm an ASA Newb.
I feel like I have tried everything posted and still no success.
PROBLEM: When connected to the SSL VPN I cannot ping any internal host's. I cannot ping anything on this inside?
Result of the command: "show running-config"
: Saved
ASA Version 8.2(5)
hostname MCASA01
domain-name mydomain.org
enable password xxbtzv6P4Hqevn4N encrypted
passwd 2KFQnbNIdI.2KYOU encrypted
names
name 192.168.2.0 VLAN
name 192.168.5.0 VPNPOOL
interface Ethernet0/0
switchport access vlan 2
interface Ethernet0/1
interface Ethernet0/2
interface Ethernet0/3
interface Ethernet0/4
interface Ethernet0/5
switchport access vlan 3
interface Ethernet0/6
interface Ethernet0/7
interface Vlan1
nameif inside
security-level 100
ddns update hostname MC_DNS
dhcp client update dns server both
ip address 192.168.1.1 255.255.255.0
interface Vlan2
no forward interface Vlan1
nameif outside
security-level 0
ip address 11.11.11.202 255.255.255.252
interface Vlan3
no nameif
security-level 50
ip address 192.168.2.1 255.255.255.0
ftp mode passive
clock timezone PST -8
clock summer-time PDT recurring
dns server-group DefaultDNS
domain-name mydomain.org
access-list SPLIT-TUNNEL standard permit 192.168.1.0 255.255.255.0
pager lines 24
logging enable
logging asdm informational
mtu inside 1500
mtu outside 1500
ip local pool VPNPOOL 192.168.5.1-192.168.5.10 mask 255.255.255.0
icmp unreachable rate-limit 1 burst-size 1
no asdm history enable
arp timeout 14400
global (outside) 1 interface
nat (inside) 1 0.0.0.0 0.0.0.0
route outside 0.0.0.0 0.0.0.0 74.7.217.201 1
timeout xlate 3:00:00
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
timeout floating-conn 0:00:00
dynamic-access-policy-record DfltAccessPolicy
aaa authentication ssh console LOCAL
http server enable
http 192.168.1.0 255.255.255.0 inside
http 0.0.0.0 0.0.0.0 outside
http authentication-certificate inside
no snmp-server location
no snmp-server contact
snmp-server enable traps snmp authentication linkup linkdown coldstart
crypto ipsec security-association lifetime seconds 28800
crypto ipsec security-association lifetime kilobytes 4608000
crypto ca trustpoint ASDM_TrustPoint0
enrollment terminal
subject-name CN=vpn.mydomain.org,OU=IT,O="mydomain",C=US,St=CA,L=Chino
keypair digicert.key
crl configure
crypto ca certificate chain ASDM_TrustPoint0
certificate 00b63edadf5efa057ea49da56b179132e8
    3082051c 30820404 a0030201 02021100 b63edadf 5efa057e a49da56b 179132e8
    300d0609 2a864886 f70d0101 05050030 72310b30 09060355 04061302 4742311b
    30190603 55040813 12477265 61746572 204d616e 63686573 74657231 10300e06
    03550407 13075361 6c666f72 64311a30 18060355 040a1311 434f4d4f 444f2043
    41204c69 6d697465 64311830 16060355 0403130f 45737365 6e746961 6c53534c
    20434130 1e170d31 33313130 35303030 3030305a 170d3134 30323033 32333539
    35395a30 52312130 1f060355 040b1318 446f6d61 696e2043 6f6e7472 6f6c2056
    616c6964 61746564 3111300f 06035504 0b130846 72656520 53534c31 1a301806
    03550403 13117670 6e2e6d65 74726f63 656c6c2e 6f726730 82012230 0d06092a
    864886f7 0d010101 05000382 010f0030 82010a02 82010100 a0d97d51 fcd18293
    eaf8e9b2 d632b2e3 e4d92eb1 5b639766 52677a26 2aa7d09d 437be3b6 dfb8649c
    4d715278 e1745955 27e8aab2 9c9da997 694a73e8 c1c426f3 a519adba acc2ad94
    aa0e09af 6db7bfc6 bad90bf2 b057dc56 c69a4276 1b826c83 6cd7ae09 af39bd7d
    4abe60b4 9b04613a 287a1ae6 9d117d05 c7cdc15f 09d588b0 fcc05c47 c1cb6d67
    c3701389 d3b7691d b05ff82c b0be475d 746a4916 0bbf11a6 7ee1b7ec bd05e1d2
    dda305a6 918bfd35 17447b04 bca1e6d9 10955649 d8211878 168c4c21 279a6584
    4b560a9f 414aea15 91e21581 a71d6b98 86d9eac3 47ea3a1d a172c71a ecf77aaa
    536d73e4 bc53eb68 c7bfacdd fab87ea5 121baf55 067dbd19 02030100 01a38201
    cb308201 c7301f06 03551d23 04183016 8014dacb eaad5b08 5dccfffc 2654ce49
    e555c638 f4f8301d 0603551d 0e041604 14fabb1d f439c41f e59207c7 202c2fda
    b46bcacc ee300e06 03551d0f 0101ff04 04030205 a0300c06 03551d13 0101ff04
    02300030 34060355 1d25042d 302b0608 2b060105 05070301 06082b06 01050507
    0302060a 2b060104 0182370a 03030609 60864801 86f84204 01304f06 03551d20
    04483046 303a060b 2b060104 01b23101 02020730 2b302906 082b0601 05050702
    01161d68 74747073 3a2f2f73 65637572 652e636f 6d6f646f 2e636f6d 2f435053
    30080606 67810c01 0201303b 0603551d 1f043430 323030a0 2ea02c86 2a687474
    703a2f2f 63726c2e 636f6d6f 646f6361 2e636f6d 2f457373 656e7469 616c5353
    4c43412e 63726c30 6e06082b 06010505 07010104 62306030 3806082b 06010505
    07300286 2c687474 703a2f2f 6372742e 636f6d6f 646f6361 2e636f6d 2f457373
    656e7469 616c5353 4c43415f 322e6372 74302406 082b0601 05050730 01861868
    7474703a 2f2f6f63 73702e63 6f6d6f64 6f63612e 636f6d30 33060355 1d11042c
    302a8211 76706e2e 6d657472 6f63656c 6c2e6f72 67821577 77772e76 706e2e6d
    6574726f 63656c6c 2e6f7267 300d0609 2a864886 f70d0101 05050003 82010100
    2484b72c 56161585 c9caa1a3 43cbc754 d3b43cef 7902a775 d40d064f 6918d52f
    0aaaea0c ad873124 11b68847 406812da fd0c5d71 6e110898 1ebddcab ddf980e4
    b95be4e2 0633cc23 7a4cbc27 f1f5e4e8 1de3c127 2b28a364 f1f26764 98afe871
    45547855 c0ceaf39 256f46db 4ac412a7 2b594817 a967ba5a 24986b24 57002ce4
    f046c6b3 5f7c9cc2 e6cd8ede 8fbcac60 b87fd497 71328783 8b148f7f affec249
    191c460b 3d46d352 0651f35e 96a60fbe 7b22e057 06aa7722 da447cd3 0ea72e7f
    5ec8c13c b550f502 b020efdc 35f62b89 52d7e6e3 14ade632 802dee70 1cdbf7ad
    a39a173b 916406e4 887ba623 4813b925 8a63a300 fd016981 a8d70651 a736267a
quit
no crypto isakmp nat-traversal
telnet timeout 5
ssh 192.168.1.0 255.255.255.0 inside
ssh 0.0.0.0 0.0.0.0 outside
ssh timeout 5
console timeout 0
dhcpd auto_config outside vpnclient-wins-override
dhcpd address 192.168.1.100-192.168.1.200 inside
dhcpd dns 66.180.96.12 64.238.96.12 interface inside
dhcpd lease 86400 interface inside
dhcpd ping_timeout 4000 interface inside
dhcpd domain mydomain.org interface inside
threat-detection basic-threat
threat-detection statistics access-list
threat-detection statistics tcp-intercept rate-interval 30 burst-rate 400 average-rate 200
ntp server 64.147.116.229 source outside
ssl trust-point ASDM_TrustPoint0 outside
webvpn
enable outside
svc image disk0:/anyconnect-win-2.5.2014-k9.pkg 1
svc enable
tunnel-group-list enable
group-policy DfltGrpPolicy attributes
vpn-tunnel-protocol IPSec l2tp-ipsec svc webvpn
group-policy VPNGP internal
group-policy VPNGP attributes
vpn-tunnel-protocol svc
split-tunnel-policy tunnelspecified
split-tunnel-network-list value SPLIT-TUNNEL
username GaryC password TGbvzEO3d6HlfU66 encrypted privilege 15
username GaryC attributes
vpn-group-policy VPNGP
tunnel-group MCVPN type remote-access
tunnel-group MCVPN general-attributes
address-pool VPNPOOL
default-group-policy VPNGP
tunnel-group MCVPN webvpn-attributes
group-alias MCVPN enable
group-url https://11.11.11.202/MCVPN enable
class-map inspection_default
match default-inspection-traffic
policy-map type inspect dns preset_dns_map
parameters
message-length maximum client auto
message-length maximum 512
policy-map global_policy
class inspection_default
inspect dns preset_dns_map
inspect ftp
inspect h323 h225
inspect h323 ras
inspect rsh
inspect rtsp
inspect esmtp
inspect sqlnet
inspect skinny
inspect sunrpc
inspect xdmcp
inspect sip
inspect netbios
inspect tftp
inspect ip-options
service-policy global_policy global
prompt hostname context
no call-home reporting anonymous
call-home
profile CiscoTAC-1
no active
destination address http https://tools.cisco.com/its/service/oddce/services/DDCEService
destination address email [email protected]
destination transport-method http
subscribe-to-alert-group diagnostic
subscribe-to-alert-group environment
subscribe-to-alert-group inventory periodic monthly
subscribe-to-alert-group configuration periodic monthly
subscribe-to-alert-group telemetry periodic daily
Cryptochecksum:1e950c041cc2c25116d30e5c884abbfc
: end
My goal is to allow Remote Users to RDP(3389) through VPN.
Thank you,
Gary
Message was edited by: Gary Culwell

Hello Jon,
Thank you so much for your response. Clients will not be connect to a specific RDP server. I was hoping if we were to establish a VPN Client tunnel I would like that tunnel to provide full local are access. So the way the clients are used to is while in the field they use RDP to connect to their desktops on the internal LAN.
Would you say this would work:
route inside 192.168.1.0 255.255.255.0 192.168.1.1 1
Do you have examples?
Thank you,
Gary

Client in same WLAN cannot ping eachother

Similar Messages

Maybe you are looking for