Clipping protection: Bounce whit "Overload Protection Only"

*from the PDF manual:*
+Overload Protection Only: Allows downward normalization in case of overloads—levels+
+above 0 dB, which would lead to clipping—but no normalization in case of lower+
levels.
in case of clipping some information is truncated and then lost, right?
I want to understand how this "*Overload Protection Only*" works in depth
is possible to have a clear response from an engineer of Logic?

Actually there's not much depth to it.
It excactly works as described in the three lines you quoted. If the final mix stream exceeds 0dBFs by amount x, then the entire file is brought down by this amount.
End of story.
Christian

Similar Messages

Does free version of VZ protect on LG G3 android have the find and lock features or just virus protection only

Does free version of VZ protect on LG G3 android have the find and lock features or just virus protection only. I've asked tech support several times and always get different answer. Am wondering if anybody uses free version and know if it has these features.
Thanks
floyd

Android has a find and lock feature built in that is accessible from your Google account. Just Google "Android Device Manager" and you can find/lock/erase your Android device from that page.
You have to activate it on your Android device first, but it's a quick setup.
Open the Google Settings App.
Click Android Device Manager.
Check the boxes.
Done.

Query Re: 'Show Clipping for Black/White Points'

Good morning.
Please can anyone help me with a query.
I have recently come across the 'Show Clipping for Black/White Points' in Levels and Curves and it's driving me mad!
Until recently, I have always opened raw images in Camera Raw or Lightroom, checked for clipping there, and if need be use the recovery or blacks sliders to recover detail. I then open my 16 bit image image in PS in ProPhotoRGB, using levels to make any alterations. I would check to see in the histogram if all is ok and left it there. It all felt pretty straight forward.
Now though I've taken to holding the alt button and going through each channel only to find that clipping occurs every time I begin to move the slider; however small.
The only way I can avoid this clipping is by leaving the levels bar alone altogether. Then there is no clipping in any channels but the image looks flat, and the histogram shows up big gaps on both sides (at least to the naked eye).
I always thought the idea was to move the sliders so there aren't big gaps on either side.
But if I move the slider say from 255 to 254, a red dot will appear, to 250, a few clusters, and by the time I've adjusted the levels to where I think it should be at 230 (based on the histogram) there will be clipping in all colours, all over the place!
I don't know what I'm meant to do. It's more frustrating because I thought I had dealt with the clipping in Camera Raw. Is there a way to avoid this whilst still moving the sliders to where I want them to be?
Thanks for taking the time to read this.

c.pfaffenbichler wrote:
So why are you pressing alt when dragging the Levels handles if the information this provides is not to your liking?
Good point! That's what I've been asking myself.
I think I was happier when I was blissfully unaware of clipping, brightening away to my heart's content! It feels as if the more I discover the less I really know.
Thanks D Fosse for the tip on curves. Much appreciated.

My Macbook Pro is frozen on the login page with a white screen and only my login picture. How do I fix this? I can't turn it off and I closed it and let it charge but it's still not working.

My Macbook Pro is frozen on the login page with a white screen and only my login picture. How do I fix this? I can't turn it off and I closed it and let it charge but it's still not working. It's only 3 months old and was working perfectly fine 30min before this happened.

Hello Kierasully,
I would start your troubleshooting with the article below for issues of not being able to log in to your Mac. Start with booting up in to Safe Boot as well as resetting PRAM on your Mac. If that does not work, then verify the hard drive with booting to the Recover HD and go to Disk Utility to verify it.
Mac OS X: Gray screen appears during startup
http://support.apple.com/en-us/ts2570
Regards,
-Norm G.

SpryMenu Appears Completely White in IE, Only

http://www.followtheprompting.com
It appears for some reason my menu is all white in IE, only. I assume there is a code tweak to address this properly. I started a new discussion to be able to award points appropriately. I reviewed the article on auto widths and it seemed to address a gap issue whereas my entire menu is white.
Thanks for any insight.

Gramps, I am doing my best to wrap my head around that article and have read it several times. It appears this is the key:
/* HACK FOR IE: to stabilize appearance of menu items; the slash in float is to keep IE 5.0 from parsing */
@media screen, projection
ul.MenuBarHorizontal li.MenuBarItemIE
display: inline;
f\loat: left;
background: #FFF;
As you have alluded to before. The big question fro my perspective is "where to insert it". Also, how much of what is above is to be inserted? It doesn't seem to follow the spry formatting, exactly. Also, is the "\" in float, a typo?

I have a white iPad, 64GB, only wi-fi, and I have 235 apps in it, now I am trying to download more apps, but it isn't happening, so my iPad can only hold that much, help me someone.

I have a white iPad, 64GB, only wi-fi, and I have 235 apps in it, now I am trying to download more apps, but it isn't happening, so my iPad can only hold that much, help me someone.

Bit more info please. Connect to iTunes on your Pc/Mac click on your icon and confirm your memory usage in the Capacity bar at the bottom of the Summary page. Try also unticking some Apps you use less frequently in the Apps section in you iPad's pages in iTunes on your pc/mac, sync afterwards to clear them off your pad then try downloading again.
Regards,Ct

Trying to create a movie clip that Bounces off four sides of the stage

using the syntax below I have created a movie clip called 'BALL' that bounces off from the left "x" and moves to the right side of the stage 'x.520' and bounces back to the start "x".
HOW DO I CREATE A MOVIE CLIP THAT BOUNCES FOUR SIDES OF THE STAGE AND STOPS ON THE FOURTH BOUNCE??
var ballTween:Tween = new Tween(ball, "x", Bounce.easeInOut, ball.x,520, 5, true);
ballTween.addEventListener(TweenEvent.MOTION_FINISH,tweenFinishedF);
function tweenFinishedF(e:TweenEvent):void{
new Tween(ball,"x",Bounce.easeOut,ball.x,0,5,true);

Here is a simplest way to do that. This code doesn't use your ball but draws it dynamically. If you want to use your ball instance - replace relevant lines.
import flash.display.Shape;
import flash.display.Sprite;
import flash.events.Event;
import flash.geom.Rectangle;
var ball:Shape;
// speed, naturally
var speed:Number = 7;
// velocity along x
var vx:Number = speed;
// vlocity along y
var vy:Number = speed;
// area within which ball may move
var moveArea:Rectangle;
// radius of ball circle shape
var ballRadius:Number = 20;
init();
function init():void
    moveArea = new Rectangle(ballRadius, ballRadius, stage.stageWidth - ballRadius, stage.stageHeight - ballRadius);
    drawBall();
    addEventListener(Event.ENTER_FRAME, moveBall);
function moveBall(e:Event):void
    // change direction if ball moves out of allowed rectangle
    if (ball.x < moveArea.x)
        vx = speed;
    else if (ball.x > moveArea.width)
        vx = -speed;
    if (ball.y < moveArea.y)
        vy = speed;
    else if (ball.y > moveArea.height)
        vy = -speed;
    ball.x += vx;
    ball.y += vy;
function drawBall():void
    ball = new Shape();
    ball.graphics.beginFill(0xFF0000);
    ball.graphics.drawCircle(0, 0, ballRadius);
    ball.x = moveArea.x + Math.random() * moveArea.width;
    ball.y = moveArea.y + Math.random() * moveArea.height;
    addChild(ball);
Message was edited by: Andrei1

Continuous Data Protection - Only for 32-bit platforms?

I want to install in Windows 7 or Windows 2008 64bit.
Thanks.

Per the CDP Data Sheet here, this is currently only developed for 32-bit OS.
Regards,

Disable download protection only. "Blocked: may contain virus or spyware"

Is there a way to do this. Many legitimate downloads are blocked by this behaviour.
Why isn't the download stopped the moment it is initiated? (spend hours downloading legitimate files and documents only to realize firefox deletes them without any user intervention) and why is there no option to recover the download?
So far the only way to fix this issue seems to be:
a) use a different browser
b) systematically lower the security settings for the browser to download a file then re-enable the options (browser.safebrowsing.enabled and browser.safebrowsing.malware.enabled)
Thank you for your time.

_scot_
As far as I know Firefox does not delete downloads. However it does screen them:
* http://kb.mozillazine.org/Browser.safebrowsing.malware.enabled
I would not recommend turning them off, however if you are downloading, it is possible to put them in another folder.

Mail bounces from one server only?

I use mail all the time with my .Mac account , as well as a Pop server account, all basically glitch free. I have one customer in Germany however, who when I send to him thru my .Mac account, the msg bounces back immediately from the mail server with (an example) of the message
The original message was received at Mon, 14 Jan 2008 05:40:07 -0800 (PST)
from asmtp002-s [10.150.69.65]
----- The following addresses had permanent fatal errors -----
<[email protected]>
(reason: 550 (result of an earlier callout reused).)
----- Transcript of session follows -----
451 4.4.1 reply: read error from mail.conradjacobson.com.
... while talking to backup-mx.hamburg.cityline.net.:
DATA
<<< 550 (result of an earlier callout reused).
550 5.1.1 <[email protected]>... User unknown
<<< 503 valid RCPT command must precede DATA
Reporting-MTA: dns; smtpoutm.mac.com
Received-From-MTA: DNS; asmtp002-s
Arrival-Date: Mon, 14 Jan 2008 05:40:07 -0800 (PST)
Final-Recipient: RFC822; [email protected]
Action: failed
Status: 5.1.1
Remote-MTA: DNS; backup-mx.hamburg.cityline.net
Diagnostic-Code: SMTP; 550 (result of an earlier callout reused).
Last-Attempt-Date: Mon, 14 Jan 2008 05:40:29 -0800 (PST)
From: YYY <[email protected]>
Date: January 14, 2008 11:40:01 AM GMT-02:00
Who do I contact to see about this? Is it their server that rejects my msg (XXX's added for privacy, just in case) or a .Mac issue? It's one of two addresses, both in Germany oddly enough.
Any help appreciated.
Thanks
Doug

You didn't say whether you've been able to reach your customer using a different SMTP (outgoing) server - though I'd be surprised if you could.
Anyway, as best as I can parse this: mac.com contacted cityline.net which contacted conradjacobson.com. While cityline was talking to conradjacobson, there was a transmission error (probably while sending RCPT, i.e., the "To:" address). When someone (mac.com ?) then tried sending DATA (i.e. the body of the email), cityline said "error, you can't send the message until we've established that the address is valid". Since the "To:" address was never validated, the overall failure was chalked up as a conventional "addressee unknown" error.
If your correspondent works for Conrad Jacobson, you may want to go to their website & use their web-based email form to try contacting him.

Why does my video clip show in the program monitor only when it is playing (the program monitor is blank otherwise)?

I am using WIndows 7 64 bit, and the most recent version of Premiere Pro CC on an I7 machine with 8GB of memory. I have imported a HD .mov clip and placed it on the timeline. When I press 'Play', it shows in the Program Monitor window. When I stop the playing, the window goes blank. I have rendered the clip (it has a yellow bar above it). Even after rendering, the yellow bar remains and the sequence only displays when it is playing. The source monitor has the same behavior.
Not being able to see where I am in a clip is making editing very difficult. I have used Premiere Elements for five years, I have taken the Lynda.com course, so I have some familiarity with the program that suggests that the frame at the point of the CTI should show in the program and source monitors.
What do I need to do to be able to see the frame in the monitors when it isn't playing?
Update: I spent 35 minutes with Tushar in a technical support chat (case number: 0186148124), during which time we deleted the contents of the Media cache folder in C:/Users/Your User Account/AppData/Roaming/Adobe/Common file (after using task manager to close coresync32.exe and creativecloud32.exe) and renamed both the Adobe folder and the 8.0 folder in Documents/Adobe/Premiere Pro/8.0. This didn't get it, but was necessary for the next step:
Going to the File menu, Project Settings, and selecting 'General Settings', Tushar had me change the Renderer to Mercury Playback Engine Software Only (I don't have a GPU accelerator video card yet). I received a warning that all previews would be deleted, which I accepted. That brought the image back to the Program Monitor.
I've posted this for anyone who may experience a similar challenge in the future. Despite a lot of Google searching before I contacted Tech Support, I didn't find anything even close to the description of the problem. I hope this provides that source for future searchers.
Jeff

Thanks, Ann. As I mentioned in my post, Tushar correctly pointed out that, without a GPU accelerated card (which I don't have - mine is a piece of junk which I will be replacing with a compatible one soon) you must use the software only settings. I had changed my project over to the 'software only' setting, and I still had the problem. The value Tushar added was the procedure for clearing the cache.
What I did originally was a newbie error, no argument. I posted it here for others who may fall in the same hole. Your reply confirms that, without a GPU accelerated card, use the software only settings (sounds so obvious, yet I missed it.....).
Jeff

Why does the website display white blank pages only?

Hello:
I use Firefox 13.0.1 on a Mac OS X, and I often go to www.wenxuecity.com for news. But, in the past couple of days, when I type in that address in the URL window, only a white blank page shows up. Nothing else! If I use Google to find direct links to a few news items at that website and click the links, I also get white blank pages. No error message or anything else.
Could you tell what is going on here?
Many thanks!

Is the page completely blank or is there still some content visible?
Can you attach a screenshot?
*http://en.wikipedia.org/wiki/Screenshot
*https://support.mozilla.org/kb/how-do-i-create-screenshot-my-problem
Use a compressed image type like PNG or JPG to save the screenshot.
You can also try to check the Net log in the Web Console (Web Developer > Web Console;Cmd+Shift+K) to see if that bring up errors about loading files.<br />
You can double click a net log entry to see more details.
*https://developer.mozilla.org/en/Tools/Web_Console
*https://developer.mozilla.org/en/Using_the_Web_Console
You need to reload web page(s) and bypass the cache to refresh all files with the Web Console panel open.
*Press and hold Shift and left-click the Reload button.
*Press "Ctrl + F5" or press "Ctrl + Shift + R" (Windows,Linux)
*Press "Cmd + Shift + R" (MAC)

Illustrator clipping mask creating white fill?!!!

Hi all,
So basically i have designed the top of a paper plane and have completed the top design which i now want to clip into the template using the clipping mask tool. I have used it exactly how it is supposed to'
1. firstly getting my shape that i want to use to clip exactly how i want it
2. then getting my image which i want to place under my first shape to use the clipping mask with
3. align it in place and bring my "shape" to the front and image to the back
then using the selection tool i select all objects then click
objects> clipping mask> make
and for some reason it clips it but the image that i wastring to clip just becomes a white fill...
i have no idea how to fix this and its driving me crazy,, i cant find a soloution no matter how long i try to fix it or research it..
i have included some screenshots below

Hi thanks so much for that! yes i did as you asked and it seems to work if i complete a rectangle clipping mask! but as soon as i copy it over and try it with my original shape, it doesnt work.... i think there is something wrong with what i have created as i showed in my last screen shot, even when i try to create a fill for my shape that i have made and am trying to use for the clipping mask it doesnt fill,, even though t says it is "filled" pink however when i completed the rectangle it had a fill of white so i knew it was ontop and that it would work,,, which isnt really happening with my shape, as it doesnt have a fill even when it says it does

White screen, boots only in safe boot

Was watching a video, switched to full screen then computer froze during the transition. Had to force shutdown by holding to power button. Now on startup the apple logo displays, spinner, appears like it will boot, screen flashes dark then displays only white screen. It will boot with Safe Boot (holding Shift while powering on), tried repair disk utilities, no luck. Did the other boot attempt by powering on holding Atl/Option + Command + R + P, it makes the computer chime go off and on again but still goes to white screen.

Additionally, when booting in verbose mode I see a lot or errors for smcReadKeyAction and smcReadData before it goes to the white screen.

Clipping mask with white brush won't work

Hi, im using photoshop cs6 on a mac and when I do a clipping mask and click and try to use a white brush to show more of the mask it doesn't work, however when I use the black brush it does work

Clipping masks are a little different from, say, vector masks. They simply take into account the content in the base layer they're clipped to, whether they're black, white or any other color.
To reveal with white, you'd have to insert a vector mask on the base layer and work from there.
ON EDIT: This assumes you have more content in the base layer to work with, so scratch that. You're probably better off just using a vector mask and concealing/revealing that way.

Clipping protection: Bounce whit "Overload Protection Only"

Similar Messages

Maybe you are looking for