Colorchecker Passport correction

I know this has been discussed before, and probably should be a FAQ, but I've looked at previous discussions and have yet to find a definitive answer. Appreciate any tips.
I think the problem is simple: I need to color-correct a RAW image that has a 24-patch Macbeth card in it. It's shot in full sunlight with a 45° angle between the lens and the sun. I know what the RGB values of the card are supposed to be:
http://xritephoto.com/ph_product_overview.aspx?ID=1257&Action=Support&SupportID=5159&catid =28
I need to do whatever needs to happen to this image to make it so that when I sample the various patches with the eyedropper in Photoshop, they're reasonably close (∆E of 7-8 would probably be adequate) to what the above chart says they should be.
I looked at Rags Gardner's work:
http://www.rags-int-inc.com/PhotoTechStuff/AcrCalibration/
But it seems to have stopped at CS5/ACR5 and I can't get it working with CS6/ACR7.1 (so far).
Is there a way to "pull" the colors in the image however they need to be shifted so that the 24 Macbeth card samples are reasonably close to what they should be according to the X-rite (or Lindbloom) charts say they should be, and the rest of the image's colors are calibrated along with it?

I think your expectations are way too high for how little color-error there should be using any sort of calibration process.  One thing to understand is that profiles optimize for the color of the light, not the luminance, and both things are tied up in the RGB numbers you are comparing.  Analyzing the difference in HSL or Lab and ignoring the L portion of either would be less misleading.
I have not let any run to completion on my slow computer, but the calibration scripts seem to work ok in CS6 as long as you set PV2010 instead of PV2012 and perhaps reset any other parameters to reasonable zero/default values that have evolved since the scripts were last tested. 
I prefer Tindemans’ script over Rags’ because Tindemans’ uses all the patches to compute the color error, not just the single primary color patch that Rags’ does.  Tindemans’ script also lets you set weights for the various patches so you can optimize for skin or landscapes or some other set of colors, because the whole set will never be all that close. 
http://www.21stcenturyshoebox.com/tools/acrcalibrator/
A few years ago I investigated various color profiles and used ColorCheck module of Imatest Studio (a few years back when it was a bit cheaper) to plot the color error:
http://www.pbase.com/ssprengel/_tech_adobecalibration
Others contributors on these forums have suggested that because the calibration scripts and the DNG Profile Editor both tweak different parts of the Adobe profile, that you could compute the slider values using the script, and then compute a DNG Profile from an Adobe profile after setting those slider values, instead of using the defaults of 0, to get a more accurate customization.  I have not attempted this, myself, but I understand the logic.
The Adobe profiles have hue-twists in them that can produce more pleasing results for real photos than profiles created with the DNG Profile Editor. so while I used to use my script-based or DNGPE-based profiles almost exclusively, now I use the ones from Adobe unless I am dealing with a subject that looks good with stronger colors or I have a unique lighting situation that might benefit from a custom profile.  For example, recently I helped shoot a wedding in a church that had white walls and an unfortunate row of lighting along the sides, with varying shades of yellowish and greenish incandescent and fluorescent bulbs.  While, I did take some calibration shots before the ceremony to calibrate to the main overhead lighting, the custom profiles I created intensified the mixed-lighting color spots along the white walls—perhaps more photometrically accurate but ugly in this scenario.  Instead, I mostly used the Adobe Standard profile or sometimes the Camera Standard profile for the bulk of the shots.
I do like using my custom profiles for outdoor scenes with bright colors in daylight and have some specialized profiles for sunset and twilight to take some of the edge off those extremes of ambient lighting.

Similar Messages

  • Aperture and colorchecker passport from X-rite

    the colorchecker passport is a tool to make color corrections by camera profiles.
    (http://www.xritephoto.com/phproductoverview.aspx?id=1257&tab=videos)
    nice program to get my color workflow better accept i use aperture and.. that just doesn't work some how. even adobe's lightroom got a plugin for this beautiful thing but aperture doesn't give any options to use a camera profile. Unbelievable because this is so important if you're doing commercial photography.
    I hope some one can help me with my issue because i dont want to leave aperture and work with lightroom...

    Just one other comment about this kind of workflow in general.
    While absolutely accurate color rendition and absolutely neutral WB can have their uses they are few and far between. Virtually every single commercial image ever viewed has nowhere near "accurate" color or WB. In fact the whole demo video itself is shot so freaking warm it's actually funny. Not only is the video shot warm but just about everything done, from the time of day it was shot to the use of gold reflectors is done to achieve warmth of color while the guy talks on and on and on about how the product helps you achieve accurate color - that's hilarious. Why would you ever go through the trouble to get the light and color so warm just to neutralize it out. His video shooter/processor/editor didn't think it was such a good idea to neutralize it - in fact the video guys actually cranked it up. Really funny stuff. Hmmm what happens when you shoot when the sun is really really warm and you use a gold reflector and a neutral WB target to adjust your WB? Answer = gold/warmth goes away - freaking brilliant. Hmmm maybe he should talk about how the video guys just set the WB to 5500 or even higher temp and captured all the wrong but warm color.
    RB
    Message was edited by: rwboyer
    Message was edited by: rwboyer

  • Colorchecker Passport not working in Lightroom 5.6

    I have been using the colorchecker passport while photographing my art for about a year now and have not had problems with it until recently.  Now Lightroom 5.6 will not show my profiles in the camera calibration area nor will it create a new profile.  When I try to create a new one it says it cannot be generated.  When I run a report I get this message:
    Plug-in error log for plug-in at: C:\Users\Joshua\AppData\Roaming\Adobe\Lightroom\Modules\XRiteColorCheckerPassport.lrplugi n
    **** Error 1
    This plug-in’s post-processing task did not finish successfully.
    XRUtility.lua:86: <AgErrorID>canceled</AgErrorID>
    I tried creating a new profile with the x-rite Camera Calibration Software and got the same report.  I don't know if the problems in with the OS, Lightroom, or x-rite.  Here is what I am using:
    Windows 8.1
    Lightroom 5.6
    ColorChecker Passport Adobe Lightroom Plug-in (3/15/2011)
    Color Checker Camera Calibration 1.0.2 (6/22/2010)
    I also tried removing all the x-rite software (both the plug-in and stand along software) and reinstall it, but that did not fix anything.
    Any ideas?

    If you can figure out how to upload your newest DNG to Dropbox I may be able to help you analyze what is wrong, otherwise, I can only guess from what you've said.  A partial substitute for uploading the DNG would be to post a screenshot of what it looks like as you did, originally so at least a judgment can be made about whether it is shot correctly or not.
    The DNG you linked from Dropbox gives me a reasonable error message, yet it seemed to give you something else.  This is what I don't understand, unless you're using the older CCPP app, rather than the slightly newer one, so first, make sure you've downloaded the 2010 version of the software and the 2011 version of the plug-in that interfaces with the software,  in case what you've installed from the disk is the original version.
    One of these links appears to be just the plug-in and one has both the software and the plug-in as separate items.  I assume the plug-in is the same for both but I'm including both links just in case one is newer.  Since the one that is just the plug-in mentions Windows 8, I assume it is the most up-to-date.
    ColorChecker Passport Adobe® Lightroom® Plug-In N/A
    X-Rite ColorChecker Passport – X-Rite Photo – X-Rite Passport
    Secondly, if you still have them try profiling the original NEFs instead of the DNGs.
    Thirdly, if you must make DNGs, it can matter what the Compatibility Level is and try an older one, since the CCPP software hasn't been updated in several years.  This doesn't seem to matter for some cameras but it does for others.

  • ColorChecker Passport

    I cannot get files that have been copied as DNG into lightroom to work with the ColorChecker Passport plug in.  If I use the stand alone adobe convertor they work.
    The files converted by lightroom also show as non valid DNG files when you try to use theColorChecker Passport stand alone profile creator.
    I am using a Mac on os x and the camera is a panasonic gh4.

    It is good you like knowledge and correct understanding, whatever that is . Knowledge and correct understanding is based upon information. Below is a table with LR Camera Raw Compatibility levels (6 as you correctly said), Camera Raw versions (30, if I did not miss any) and a list Adobe DNG Converter versions (42, if I have not missed any). In the interest of knowledge what I would like to know is:
    1) which version of the DNG specification each version of the Adobe DNG Converter supports
    2) If converting RAW files within LR, which versions of the DNG specification applies for each compatibility level.
    This is really my main interest in this thread and I cannot find that information anywhere, all I conclude from the thread is that 4.6 and later is likely to use DNG file specification 1.2 and 7.1 and later is likely to use DNG file specification 1.3 or 1.4 (my guess is 1.3).
    Happy to open a new thread if this is of any interest.
    LR Camera Raw Compatbility
    Camera  Raw
    Adobe DNG Converter
    2.4
    2.4
    2.4
    3.1
    3.1
    3.2
    3.2
    3.3
    3.3
    3.4
    3.4
    3.5
    3.5
    3.6
    3.6
    3.7
    3.7
    4.0
    4.0
    4.1
    4.1
    4.1
    4.2
    4.2
    4.3.1
    4.3.1
    4.4.1
    4.4.1
    4.5
    4.5
    4.6
    4.6
    4.6
    5.1
    5.1
    5.2
    5.2
    5.3
    5.4
    5.4
    5.4
    5.5
    5.5
    5.6
    5.6
    5.7
    5.7
    6.1
    6.1
    6.2
    6.2
    6.3
    6.3
    6.4
    6.4.1
    6.5
    6.5
    6.6
    6.6
    6.6
    6.7
    6.7
    6.7.1
    7.1
    7.1
    7.1
    7.2
    7.3
    7.4
    8.1
    8.2
    8.3
    8.4
    8.5
    8.6
    8.7
    8.7.1

  • Colorchecker Passport and Aperture 3

    Hi everyone,
    So, I was at the DFW Photo Expo today and attended some free seminars. One was on DSLR video (very good class) and one on color management. In the color management class, the class pretty much evolved around X-Brite Colorchecker Passport and Lightroom. I thought that it was very interesting, especially adjusting your RAW files to a certain standard.
    As I have found out, the automated features only work in Lightroom and I think that the instructor said Photoshop (neither of which I have). It appears that Aperture is left out of the running if you want to use the features that Colorchecker Passport has.
    As I haven't bought Aperture 3 yet, but I plan to, is there a need for something like this in Aperture to adjust for your camera (I have a Canon 60D) or is there an alternative? I know that there is a divid between Mac photographers between Aperture and Lightroom, so I don't want this thread to go down this path. I am concerned as to the best way to capture the true colors from what the camera saw and my eye saw. Also, there is the issue about color correcting your monitor and the importance (or not) of doing that. I have a fairly new 27" iMac that seems to look great to me. And of course the printer too.
    I know this is a multi-question post, but I'm hoping that some of you out there in Appleland can point me in the right direction.
    Thanks, Mark

    chacro wrote:
    I currently brush color adjustments to try and even things out. It works, but one day I hope to see brushable white balance.
    You and me both  .
    In the meantime, take a look at the Tint controls, both in the Enhance Brick and as a Quick Brush.  The advantage of the Enhance controls are that you can apply the color shift separately to each of the three major divisions of the luminance gamut (first things to try are warming your darks and cooling your mid-tones, and vice versa).  The advantage of the Tint Brush is in it's use for one-area or one-object hue shifts.
    Here's the Enhance Brick showing some Tint values applied:
    And here's a (quick & dirty -- ignore it as a photo) example of the Tint Brush at work -- the sky as recorded is entirely pale cyan.
    For architectural photographs each of these can put to effective use, and (imho) provide their own functionality a little quicker than the Color Brick tools (which, of course, I also use regularly).

  • Lightroom 5  colorchecker passport

    I was not able to send a prset file to colorchecker passport. Bcs: The profile could not be created. "Could not generate illuminant from DNG. Images must be created using asupported illuminant and correct exposure."
    Thank you for the help.

    Hi Sprengel,
    I don't mind but I don't think it is the raw file problem becuse I did try with my other cameras such has Leica, Olympus...and it came out with the same problem.
    Here is the information of the prompt up flash:
    From C:\Users\UserName\AppData\Roaming\Adobe\Lightroom\Modules\XRiteColorCheckerPassport.lrplu gin with the information below:-
    OMP: Warning #2Cannot open message catalog "2052\libiomp5ui.dll
    OMP: System error #126: cannot find the modules。
    OMP: Info #3: Default messages are used
    OMP: Error #15: Initializing libiomp5md.dll. but found libguide40.lib already initialized.
    OMP: Hint: This may cause performance degradation and correctness issues. Set environment variable KMP_DUPLICATE_LIB_OK=TRUE to ignore this problem and force the program to continue anyway. Please note that the use of KMP_DUPLICATE_LIB_OK is unsupported and using it may cause undefined behavior.
    Hope this will help. Thank you again.
    Regards.

  • Colorchecker passport and the DNG profile editor

    I finally got around to getting a Colorchecker passport to use with the DNG profile editor.
    I was secretly hoping I could save time by shooting the chart on location and make an instant profile out of that - then the colors would be at least "close ballpark" so I would just have to apply white balance and then move on to more specific adjustments. But of course it wasn't that easy, it still takes a fair bit of color tweaking to get right in most circumstances.
    So I'm wondering if my energy would be better spent trying to perfect one good dual illuminant general profile. For this I would use 3000 K tungsten at one end and 5500 K studio flash at the other. Or would it be better to use overcast daylight? In either case it's obviously important to ensure the chart is absolutely evenly lit.
    And then I should probably have a separate profile for fluorescent tubes.
    I'm curious what other people's experiences with the colorchecker/DNG profile editor are? How are you using it?

    The color profile changes with the lighting, so a profile that was computed for daylight won’t be right for tungsten or fluorescent.  Keep in mind that a custom camera profile is the set of corrections on top of an existing Adobe profile that the DNG has assigned to it, perhaps Adobe Standard, and all Adobe profiles are dual-illuminant profiles, so it makes sense you’d want to also create a dual-illuminant profile for general purpose use that has the same two lighting scenarios as Adobe used:  2850K and 6500K.  The 6500K is the tricky one because full sun is warmer, closer to 5000K, and you need the right amount of haze to create 6500K sunlight, unless you are using standard D65 bulbs, indoors, which is likely what Adobe does.
    I use a dual-illuminant profile for general purpose use, but since the WB-Tint values of both the tungsten and daylight ends are close to zero, lighting that has a tint not close to zero needs a separate profile.  The common example is the greenish light from fluorescents, and I have several single-illuminant profiles for various artificial lighting scenarios with WB-Tint values that are relatively non-zero.  I also have ones for very red sunsets and very blue twilight.  If I had studio lighting I’d make a profile for that.  Sometimes I make a custom profile for a church or other venue that has significant non-neutral walls or ceilings, or where sunlight through the stained-glass windows shining on the walls are giving a significant color-cast including a non-zero tint value to the lighting.  If you know you’ll be doing some shots near a large amount of tall, green vegetation then a custom color profile can correct for the green tinge to the ambient lighting coming down from above mixing in with the sunlight. 
    Adding to the suggestion about wearing neutral clothing, I’d argue for dark neutral clothing because something lighter clothing will reflect environmental colors (sunlit vegetation or brick walls, etc, outdoors) and not be neutral. 
    Besides non-neutral clothing, try to avoid areas that have green grass or tree leaves or brick buildings that also color the light and reflect off the colorchecker.   For the sunlit shots, I put my colorchecker face up on the sidewalk or parking lot, to avoid coloration from the grass and far away from trees or buildings especially in the direction I’m pointing the camera, so the only lighting is direct sun and ambient blue-sky, possibly diffused by hazy clouds.  I point the camera down at the colorchecker, at a 45-degree angle and at a compass direction and not directly toward the sun, nor directly away from the sun.  I try to shoot the target that is face up on the ground perhaps at a 90-degree angle from the sun to minimize any residual glare from the colorchecker’s slightly non-matte surface.  Obviously directly away from the sun, the color-checker will have my shadow on it or I will be blocking the light from the sky near the sun.
    I use the same sort of process for the tungsten end, choosing a room with neutral walls and put the target relatively flat on the floor facing up, perhaps tipped up somewhat toward the light, but not so much as to have any glare from the lighting, either, in other words, not with the lighting directly behind the camera, but somewhat over to the side.

  • Does X-RIte MSCCPP ColorChecker Passport work with Photoshop Extended CS3 Version 10.0.1 running under Mac OS 10.6.8?

    My iMac is running 10.6.8, but some of the newer color checkers require 10.7 or higher.
    Amazon has a listing for the X-Rite MSCCPP ColorChecker Passport. The system
    requirements mention Adobe Camera RAW 4.5 or newer, Mac OSX 10.4.11 or 10.5X.
    Will the X-Rite work with my CS3 Extended version 10.0.1?

    Thanks to all participants for their advice. Having purchased the Xrite MSCCPP ColorChecker Passport, I can say that
    the short answer to my question (amended to saying my camera is an Canon XTi) is "yes".
    Instructions for using a newer version of the CCP are given at
    http://www.xrite.com/documents/manuals/en/ColorCheckerPassport_User_Manual_en.pdf.
    The same steps apply to the MSCCPP version.
    In the reviews of the MSCCPP on Amazon, be sure to read Louie Aquinaldo's advice about not upgrading
    from the included software version 1.0.1 to 1.0.2.

  • X-Rite ColorChecker Passport specifically targeted at DNG workflow

    Hi folks, I reviewed the X-Rite ColorChecker Passport system
    (review of ColorChecker Passport here: http://www.it-enquirer.com/main/ite/more/colorchecker_passport/)
    What I find mildly annoying in this X-Rite solution is that it only creates DNG profiles. While that is great when you're working with Lightroom and Photoshop only, it's ineffective if you also use other applications like Capture One Pro.
    You can of course use the ColorChecker hardware to create an ICC profile, using ProfileMaker, but I was wondering if one can't convert a DNG profile to ICC. I tried to open the DNG profiles on my Mac OS X machine, but they aren't package bundles, so there is no measurement data to be extracted for example...

    With full disclosure, I don't own the color checker passport but I've played around with it and I agree that it is pretty cool. I haven't used it in conjunction with an Aperture workflow, but Aperture is my main tool in processing/maintaining my image files (along with photoshop). The software that allows the colorchecker to work with photoshop/acr/lightroom is pretty usefull, but unfortunately, as you've found, the colorchecker doesn't work with Aperture in the same way.
    My suggestion would be that while you can't create profiles in the same fashion in Aperture using the colorchecker as the colorchecker does with lightroom, you can still make a preset based upon the passport itself.
    I'm pretty sure that you could make global adjustments/enhancements to an image of the passport, make a preset, and apply it to other images in similar lighting. Not as slick as the interfacing of the colorchecker and acr/lightroom but I'm pretty sure it would work nicely.
    I'd be curious to hear with others have to say.
    Best,
    CD
    Message was edited by: ChristopherDavid

  • ColorChecker Passport - Camera Raw

    Hello,
    I recently purchased the ColorChecker Passport from X-Rite...
    When I click on "Create a Profile"... I have an error message saying that it is  not possible to create a profile with this image... This message can appear at the beginning of the process or at the very end (after many tries)... (see image... sorry it's in french !)... My picture is not overexposed... not even cropped !
    I'm not able to solve this problem...
    Hope you have a solution...
    Many thanks for your help...

    Hi
    May be one ore more (R, G ord B) channels are burned-out for one or more tones.
    You could test it with ACR.
    It's better to manually expose using if possible the "spot" type exposure on Your camera measuring on exactly the 4th gray patch on the last row (this patch corresponds to 18% gray metering). This should assure well-exposed images.
    Be careful to make the target planar to the lens axis and do not put reflecting obljects around the target, even if out of scene. This can relfect on the target itself.
    If You are unable to obtain a good picture, You can attach one of Your RAW to verify overexposed areas.
    Massimo

  • ColorChecker Passport-Color Profiles

    Hi there,
    I am photographing paintings with Elinchrom flashes with an even light and I use the ColorChecker Passport from X-Rite to keep a reference in order to match the colors.
    Till now, I've been using the software DNG profile manager, provided with the ColorChecker Passport from X-Rite, which creates a camera profile that should be helpfull to get the right color. Once I've applied the new camera profile (after restarting lightroom), I do the white balance. It's recommended on the X-Rite tutorial to use the target number 20 called "neutral 8" to do the white balance. I've also tried the target 22 called "neutral 5", and it seems to get slightly better results.
    I've noticed that even creating a color profile and doing the white balance the colors don't match. I am using a mac laptop screen that I calibrate quite often, which is not very helpful for obvious reasons, but that helps to keep track of the general look of the image, so that's why I keep the color adjustment to the RGB numbers.
    I've downloaded the following PDF; here there is some information about the RGB values of various ColorChekers:
    http://www.google.com/url?sa=t&source=web&cd=2&ved=0CB4QFjAB&url=http%3A%2F%2Fwww.babelcol or.com%2Fdownload%2FRGB%2520Coordinates%2520of%2520the%2520Macbeth%2520ColorChecker.pdf&rc t=j&q=ColorChecker%20rgb%20values&ei=wOCdTbG7NIyDhQelj5G8BA&usg=AFQjCNGj3wUpWC_uMxgMCeR3GI yN7kDU0A&sig2=mPf1grSAULxyMs_SanYVNw&cad=rja
    Using these values and a selective color layer in photoshop I get close to the real colors, although it is not good enough.
    My questions are:
    1-Does anybody know the ColorChecker Passport RGB (Adobe 98) values?
    2-I've tried to use the DNG profile editor because it seems a precise tool for this, but it doesn't recognise the 5D Mark II files. Is it because this application hasn't been updated? It also seems to work only with 6500K or 2850K, which is not the case of the Elincrhom 600 monoblocks I am using (which I think are around 5000K.
    3-Could anybody recommend a workflow that's better to match the colors?
    I have more questions, but I think these three are a good start.
    Thanks!

    Here are color-error analysis plots for several camera calibrations using the fine-art color-checker calibration shot uploaded, earlier.
    The three profiles tested were:
    1)  A custom Elinchrom Flash profile I created from the color-checker using the DNG Profile Editor,
    2)  The Adobe Standard camera profile,
    3)  The custom profile provided by Gustov.
    My general comment would be that the Adobe Standard profile has about the same error as the custom profile I computed using the DNG Profile Editor but the Adobe profile has a more even distribution of the color error.
    The profile Gustov provided seems to be very close in the yellow area, but quite far off in the reds, blues, and violets. This can also be seen as a severe shift toward the green of the WB Tint slider value when the profile is selected for the As Shot WB as compared to the almost zero value when using the Adobe Standard profile.
    These color-error plots were created using the ColorCheck module of Imatest Studio 3.7 from www.imatest.com.  The program compares the measured color values from a color-checker image to the standard color numbers of the Color Checker then plots the difference on a CIE chromicity diagram, where the squares are the standard color position, the circles are the measured color position, and length of line in between is the color-error.  In general, error in-and-out from the center is saturation error, while error around the center is hue error.  In a 3D plot luminance error is also shown but harder to visualize without a way to rotate the plot around.  Imatest provides this visualization in its Multicharts module.
    I used the ProPhotoRGB colorspace when saving the TIF out of ACR because the standard ProPhotoRGB color-checker numbers in Imatest are for D50 lighting whereas the AdobeRGB standard numbers are for D65 lighting.  As the image-filenames suggest, I used a linear toning curve and a black-point of 0 when saving out of ACR, but left the brightness at 50 and the contrast at 25.  I tried zeroing out the brightness and contrast or using the Medium Contrast toning curve but things were way off.  Using a blackpoint of 0 instead of the default of 5 also made things slightly better.  There are scripts that can compute the optimal toning values for the gray patches but I was only comparing profiles, not trying to optimize them completely.

  • X-Rite ColorChecker Passport workflow?

    Anyone using an X-Rite ColorChecker Passport for adjusting color, or creating profiles? I'd like to do this for important shots, or shooting sessions with consistent light.
    It is very useful to shoot a test shot of the ColorChecker Passport and use it with the ColorChecker software, ACR 6, and Photoshop CS5 to adjust color in a particular lighting situation. IMO, it improves color from shots with a Nikon D700. It also helps keep color looking consistent when shooting with two different cameras.
    I'm trying to figure out if there is a way to use ColorChecker test shots in Aperture. Anyone have suggestions?

    With full disclosure, I don't own the color checker passport but I've played around with it and I agree that it is pretty cool. I haven't used it in conjunction with an Aperture workflow, but Aperture is my main tool in processing/maintaining my image files (along with photoshop). The software that allows the colorchecker to work with photoshop/acr/lightroom is pretty usefull, but unfortunately, as you've found, the colorchecker doesn't work with Aperture in the same way.
    My suggestion would be that while you can't create profiles in the same fashion in Aperture using the colorchecker as the colorchecker does with lightroom, you can still make a preset based upon the passport itself.
    I'm pretty sure that you could make global adjustments/enhancements to an image of the passport, make a preset, and apply it to other images in similar lighting. Not as slick as the interfacing of the colorchecker and acr/lightroom but I'm pretty sure it would work nicely.
    I'd be curious to hear with others have to say.
    Best,
    CD
    Message was edited by: ChristopherDavid

  • ColorChecker Passport and Lightroom 4

    How do i delete a colorchecker passport custom profile from selections of camera calibration in lightroom 4 and Mac OS 10.8.3?

    Once you find the location mentioned in the thread, below, just delete the .dcp files you no longer want, or at least move them the some other place outside of the CameraProfiles subfolder:
    http://forums.adobe.com/message/4982158

  • X-rite colorchecker passport profile created but does not appear in the  Camera Calibration tab!

    I have installed x-rite colorchecker passport and lightroom 5.0. I followed the tutorial in setting up my camera profile and lightroom reported created successfully. However after restarting Lightroom, I could not find my created profile other than the Adobe Standard in the Camera Calibration tab.
    Please help !

    X-Rite has a free DNG Profile Manager that can be downlaoded after registering your ColorChecker Passport here:
    http://www.xritephoto.com/ph_registration.aspx
    You will be offered a link to download the free app. See if the profile you created is visible with the app.
    Here's where the user camera profiles should be located with LR5:
    Windows—C: \ Users \ [your username] \ AppData \ Roaming \ Adobe \ CameraRaw \ CameraProfiles \
    Mac—Macintosh HD / Users / [your username] / Library / Application Support / Adobe / CameraRaw / CameraProfiles /
    Profiles are camera model specific so a Canon 600D camera profile will only be visible when a 600D raw image file is selected. You need to create profiles for each camera model separately.

  • X-Rite's ColorChecker Passport with Aperture

    I would like to use X-Rite's ColorChecker Passport with Aperture.
    Is anybody aware whether Apple's Tech people are talking to X-Rite to enable using both together? 

    The ToU forbid discussion of anything but released products.  You will not find an answer here.  Fwiw, I have no idea.
    The Passport is an object with no electronics.  How does Adobe's software communicate with it?

Maybe you are looking for

  • Error on Query which is based on Infoset.

    Hi SAP Gurus, We have created the Query based on 2 ODS and one Infoobject. ODS2 is joined to ODS1 Infoobject is joined to ODS1 both the joins are outer join... We are getting the error when we are executing the Query Error is " SQL error for Info pro

  • More item categories than attached to the document type

    Hi Friends, When i checked the possible item category list for a item for a given sales order, there are many item categories than that of the item categories assigned in the VOV4. Could any body guide me, if there are any other way this can be linke

  • Web Dynpro Component cannot be found in list when Creating Callable Object

    Hi All,     I have created a web dynpro component and implemented the IGPWebDynproCO interface, after that I deployed it into the J2EE engine.     But in the step of choosing the web dynpro component as a callable object, I cannot find the one I crea

  • Unit of Messure issue

    Hi, All, I have a question on Unit Messure. What happened if Unit of Messure in General View is different the Unit of Messure in Purchasing View in Material Master Data? Can I change Unit of Messure in Purchase Order? Then do a goods receipt in diffe

  • Won't load startup config

    I've got a strange problem where the router won't boot with the startup config. When I type 'sho start' I see my config displayed but when I type 'sho run' it shows the generic config with none of the changes I made. Also, every time I power cycle th