Communication problem between Cisco 3560 and Cisco SG300.

Dear Support,
I have a Cisco SG300 and Cisco 3560 switches.
3560 is my Core Switch and SG300 is access switch.
From 3560 VLAN information is not passed to SG300.
3560 Configuration:
interface GigabitEthernet0/23
switchport trunk encapsulation dot1q
switchport trunk allowed vlan 1,2,10,11
switchport mode trunk
SG300 Configuration:
interface gigabitethernet49
spanning-tree link-type point-to-point
switchport mode general
switchport general allowed vlan add 2,10-11 tagged
macro description switch
Please suggest how this issue is resolve.
Regards,
JItesh Mahajan.

Dear Aleksandra,
Below Configuration is right or wrong for 3560 and SG300.
3560 Configuration:
interface GigabitEthernet0/23
switchport trunk encapsulation dot1q
switchport trunk allowed vlan remove VLAN 1
switchport native vlan 1
switchport trunk allowed vlan 1,2,10,11
switchport mode trunk
SG300 Configuration:
interface gigabitethernet49
spanning-tree link-type point-to-point
switchport mode general
switchport general allowed vlan add 2,10-11 tagged
macro description switch
Regards,
JItesh Mahajan.

Similar Messages

Communication problem between ASA 5510 and Cisco 3750, L2 Decode drops

Having problem with communication between ASA 5510 an Cisco Catalyst 3750.
Here is the Cisco switch port facing the ASA 5510 configuration:
interface FastEthernet2/0/6
description Trunk to ASA 5510
switchport trunk encapsulation dot1q
switchport trunk native vlan 50
switchport trunk allowed vlan 131,500
switchport mode trunk
switchport nonegotiate
And here is the ASA 5510 port configuration:
interface Ethernet0/3
speed 100
no nameif
no security-level
no ip address
interface Ethernet0/3.500
vlan 500
nameif outside
security-level 0
ip address X.X.X.69 255.255.255.0
There is a default route on ASA to X.X.X.1.
When I try to ping from ASA X.X.X.1 i get:
Sending 5, 100-byte ICMP Echos to 31.24.36.1, timeout is 2 seconds:
Also in the output of show interface eth 0/3 on the ASA i can see that the L2 Decode drop counter increases.
I have also changed the ports on the Switch and ASA but the same error stays.
Any thoughts?

I don't see anything wrong with your trunk configuration; I have a similar one working between an ASA 5520 and a Catalyst 3750G.
Maybe you should adjust the "speed 100"? In my experience, partial autoconfiguration results in duplex mis-matches, which results in dropped packets.
I'd try removing the "speed 100" and letting the ASA port autonegotiate with the switch. Alternatively, have both sides set
speed 100
duplex full
and see if things improve.
-- Jim Leinweber, WI State Lab of Hygiene

Communication problem between FPGA VI and Host-PC VI

Dear,
I am trying to set up communication between an FPGA an the host-PC using FPGA FIFO's.
The communication still has some problems and I don't know what would cause them.
Labview gives me the following reason "The transfer did not complete within the timeout period or within the specified number of retries."
What is wrong with my labview program? How can i solve this?
The Project can be found in attachment.
Best regards,
Jasper Beurms
Solved!
Go to Solution.
Attachments:
CEC20_02.zip ‏150 KB

Hello Jasper,
Are you fully familiar with how DMA FIFOs work on a cRIO?
Some general questions:
- Is there a specific reason that you need to use DMA FIFOs?
You seem to only require a 10 msec acquisition rate?
- Wouldn't it be easier to just use the Scan Engine in the case you don't need to go below 10 msec?
The Scan Engine should allow you to do acquisitions at this rate without even having to implement FPGA code yourself.
Another benefit is that the Shared Variables created/published by the Scan Engine are also by default visible over the network/
If want to use DMA FIFOs, then I would suggest you take a look at the Compact RIO Developer's Guide: http://www.ni.com/compactriodevguide/
I would advise that you read out the DMA FIFOs on a VI that is running on the RT Controller (RT VI) and then send those values from the RT VI over the network to your Windows VI.
You could use for example Shared variables to sent values from the RT VI to the Windows Host VI.
Another solution might be to use network streams or more custom TCP/IP communication.
If these concepts are new to you, then please have look at the Compact RIO Developer's Guide: http://www.ni.com/compactriodevguide/
This Guide should explain you all the basics you need to know.
If something is unclear or requires further explanation, then please let me know.
Kind Regards,
Thierry C - Applications Engineering Specialist Northern European Region - National Instruments
CLD, CTA
If someone helped you, let them know. Mark as solved and/or give a kudo.

Communication Problem between RTD,Pt1000 and MAX

Bonjour,
J'ai un probleme de communication entre MAX et un Agilent,
Je dispose d'un agilent 34970A, d'un GPIB et d'une carte insere dans l'agilent (34901A).
Avec MAX je communique avec "communicate with instrument" en language SCPI,
J'ai reussit a connaitre les temperature de mes Pt100 4 fils et des thermocouples dont les commandes sont:
Thermocouples de type J: MEAS:TEMP? TC, J, (@203)
Pt 100, 4 fils: MEAS:TEMP? FRTD, (@201)
Mon probleme est de communiquer avec la Pt1000 sur le port CH6
J'ai essayer:
MEAS:TEMP? RTD, 85,1, 3E-06, (@206) mais on a par default la valeur d'une Pt100 2 fls
Lorsque l'on configure la resistance avec TEMP:TRAN:RTD:RES 1000, (@206) cela fonctionne car si on lui demande TEMP:TRAN:RTD:RES? (@206) on a bien les 1.0000E+03 ohms. Mais je ne peut pas demander la temperature par la suite.
Merci d'avance pour vos reponse.
If you don't understand French I can translate.

About this two kind exemple they are working:
MEAS:TEMP? TC, J, (@203) and MEAS:TEMP? FRTD, (@201) for the measure of Thermocouple and RTD 4W,Pt100.
But for the RTD 2W, Pt1000 it doesn't work.
Could you give me an exemple of measurment for this Pt1000 please ?

Communication problem between Adobe Form and WebDynpro

Hi all,
I have the following problem and am thankful for any help I can get from you in order to solve it:
I created an Adobe Form in WebDynpro. In both the WebDynpro as well as in the Adobe Form, I created a Submit Button (which I binded to the same method) as well as a text field (which I binded to the same context attribute). When I do changes in WebDynpro, everything works fine and the changes are displayed in the Adobe Form as well.
But when I do changes in the Adobe Form, these changes are not submitted. Also the Submit button in the Adobe Form is not working.
I send the project to a colleague and she could deploy and run my project without any problems. So I think it is a problem with my settings or installation. I already did a reinstallation of the NW Developer Studio as well as the Adobe Lifecycle Designer. But it did not help.
Did anyone have a similar problem or has a suggestions what else I could do?
Thanks in advance,
Thorsten

Hi Thorsten,
If the submit button doesn't do anything, it usually means there's something wrong with your client software.
Are you using NW04s or NW04? NW04 only supports ACF (Active Component Framework) forms, whereas NW04s also supports ZCI (Zero Client Installation) forms (there're different Submit buttons in Adobe LiveCycle Designer). Reader 7.0.9 should definitely work in all cases, but Reader 8.0 (and Reader 8.1, released yesterday) doesn't work properly with ACF forms (there's an SAP note on this subject).
To use ZCI forms, all you need is Adobe Reader at client side. To use ACF forms, you also need some other client software: either (the correct version!) SAP Active Component Framework (stand alone software that you can download from SAP Marketplace; it's part of some SAP note; search for xACF and select the correct version of the note). A better option is not to install xACF manually (uninstall it if present, using Control Panel > Add/Remove programs), but to use the ActiveX control instead (reinstall it in your case because of the problem you have). First kill the AcroRd32.exe process, if it is running. Then go to "C:\WINDOWS\Downloaded Program Files" and delete the file AdobeControl(s) (NW04) or AcfControls (something similar; NW04s) if present. Then access your form in your Web Dynpro application using IE (Firefox doesn't support ActiveX; the only option is to use ZCI forms with non-IE browsers). If all goes well, prior to displaying the form, IE should ask to install an ActiveX control (it will only be asked if you have sufficient privileges, that is belong to the local Administrators group).
Kind regards,
Sigiswald

Communication problem between NetBeans and Tomcat

hi!
i got a quite mysterious problem. here is what happens:
- i start NetBeans 5.5.1 (the first time)
- i want to debug my JSF-Project, the Debugger starts
- After a few seconds the debugger waits for tomcat (it sais: "Waiting for Tomcat...") and tomcat starts
- Again after a few seconds the tomcat-debugger-output sais "Tomcat startet in 3333 ms".
okay.
when i enter http://localhost:8084/ in my browser i get the tomcat homepage, so the server has definitely started! But nothing happens in NetBeans and nothing happens with my project....
In the lower-right corner i see this blue working-bar that sais "deploying project" but nothing happens. The Project-Debugger-Output still sais "Waiting for Tomcat..." but nothing happens...
And after something around 3 minutes (i guess it's a timeout) i get the error "Starting of Tomcat failed." But is HAS started, i can login to the Administration-Area in my browser!
so i guess there is a communication problem between netbeans an tomcat. Netbeans waits for a message from tomcat but tomcat doesn't send it..or netbeans doesn't understand it.
But the story goes on:
When i press the debug-button a second time it takes only a few seconds till i get the message: "Tomcat server port 8084 already in use". OF COURSE! Because Tomcat has already startet and can't be stoped by NetBeans.
i'm trying to solve this problem for 4 days now, so i would be very happy if anyone has an idea where to start/continue the search...
thanks,
flo.
some system-info:
- windows vista business 32-bit
- no firewall is running
- AntiVir Personal Edition IS running
- Yahoo Widgets Engine IS running
- no other software is running
and finally the tomcat-log:
Using CATALINA_BASE: C:\Users\Administrator\.netbeans\5.5.1\apache-tomcat-5.5.17_base
Using CATALINA_HOME: C:\Program Files\NetBeans\enterprise3\apache-tomcat-5.5.17
Using CATALINA_TMPDIR: C:\Users\Administrator\.netbeans\5.5.1\apache-tomcat-5.5.17_base\temp
Using JRE_HOME: C:\Program Files\Java\jdk1.5.0_12
Listening for transport dt_shmem at address: tomcat_shared_memory_id
21.09.2007 18:27:50 org.apache.catalina.core.AprLifecycleListener lifecycleEvent
INFO: The Apache Tomcat Native library which allows optimal performance in production environments was not found on the java.library.path: C:\Program Files\Java\jdk1.5.0_12\bin;.;C:\Windows\system32;C:\Windows;C:\Windows\system32;C:\Windows;C:\Windows\System32\Wbem;C:\Program Files\QuickTime\QTSystem\;C:\Program Files\ThinkPad\ConnectUtilities;C:\Program Files\Common Files\Teleca Shared;C:\Program Files\Common Files\Adobe\AGL;C:\Program Files\MySQL\MySQL Server 5.0\bin;C:\Program Files\cvsnt;
21.09.2007 18:27:50 org.apache.coyote.http11.Http11BaseProtocol init
INFO: Initializing Coyote HTTP/1.1 on http-8084
21.09.2007 18:27:50 org.apache.catalina.startup.Catalina load
INFO: Initialization processed in 1862 ms
21.09.2007 18:27:50 org.apache.catalina.core.StandardService start
INFO: Starting service Catalina
21.09.2007 18:27:50 org.apache.catalina.core.StandardEngine start
INFO: Starting Servlet Engine: Apache Tomcat/5.5.17
21.09.2007 18:27:50 org.apache.catalina.core.StandardHost start
INFO: XML validation disabled
21.09.2007 18:27:53 org.apache.coyote.http11.Http11BaseProtocol start
INFO: Starting Coyote HTTP/1.1 on http-8084
21.09.2007 18:27:54 org.apache.jk.common.ChannelSocket init
INFO: JK: ajp13 listening on /0.0.0.0:8009
21.09.2007 18:27:54 org.apache.jk.server.JkMain start
INFO: Jk running ID=0 time=0/31 config=null
21.09.2007 18:27:54 org.apache.catalina.storeconfig.StoreLoader load
INFO: Find registry server-registry.xml at classpath resource
21.09.2007 18:27:54 org.apache.catalina.startup.Catalina start
INFO: Server startup in 3626 ms

As i wrote before, the same problem occured for me. I have found a solution which is : Go to tools menu and then select options . In the proxy info, select No Proxy.
I hope this help you

Difference between Cisco DCNM and CISCO Fabric Manager

Hello Everyone,
I am new to Cisco SAN and just would like to know the differences between cisco DCNM and Cisco Fabric manager and which one is latest as of now.
regards
VINAY

Hi Viany,
Fabric Manager was renamed DCNM starting at 5.2.
Fabric Manager only monitors SAN Fabrics, while DCNM 5.2 and above can monitor both SAN Fabrics and Ethernet LANs.
Regards,
David

I am having one application which i am going to install on my ipad and i am having one external device having USB interface. I want to have communication in between my device and ipad over USB/BT. is it possible

My external device is having male USB connector. The cable available in market are having can be plugged to the device having female connector.I will need converter in between as my device is having male connector. Can i get such cable? If yes can i establish communication in between my app and device over these cables.I am not passing any audio/video data or photos.I am sending data frames. My device is having firmware and it sends data frames in firmware understandable format. Let me know can i have two way communication in between over USB/BT?
Right now i am connecting my device with host PC and i want to replace my host PC with ipad.

Thanks....
will it be possible to establish communication in between my device and app. Because camera conection kit only transfers photos and videos and my device doesnt have any audio/video data.
If yes, should i add photo header to my frames and will send as corrupted photo file or what needs to implement so that i can have sound communication in between.

I have a communication error between Lightroom 5 and my printer. It prints photos about 1/2 strength in color. Printer checks out ok. WHAT CAN I DO?

I have a communication error between Lightroom 5 and my printer. It prints photos about 1/2 strength in color.. The printer checks out ok. What can I do?

Externalizable problems between v1.3 and v1.4

Hej you.
I have strange problems with the Externalizable objects.
I Use many Object to Save my file, but wien i try to Externalizable on J1.3 and Denalizable again in J1.4 I got this message:
E:\Programmer\Java\ProrgamName>Java ProrgamName
javax.swing.JInternalFrame; Local class not compatible: stream classdesc serialV
ersionUID=8792953236056021037 local class serialVersionUID=-6387351733537024688
Can i trap J1.4 ID to use 1.3 ID, so it can use on ALL platforms, not just locally?
When I Save and load on the same machine it works fine, but not when i moving to another machine with 1.4. Is a another method, or i Need to save all object to AscII instead in this smart method (that are poorly work)? I have surfed around javasoft.com with finding a answear.
See my early quenstien on (closed):
http://forum.java.sun.com/thread.jsp?forum=31&thread=273990
With very regaards By:
Super Bomba, Denmark
PS. No Duke Dollars this time. Sorry.

Hey.
I found how to work around combatible problems between 1.3 and 1.4. For user, that want to save thier DynamicTree.java (http://java.sun.com/docs/books/tutorial/uiswing/components/example-swing/index.html)
Use follow code (I using Externalizable):
protected DefaultMutableTreeNode rootNode=null;
protected DefaultTreeModel treeModel=null;
public void writeExternal(ObjectOutput stream) throws IOException
{ stream.writeUTF(rootNode.toString());
    Vector values = new Vector();
    Object root = treeModel.getRoot();
    // Save the root, if its Serializable.
    if(root != null && root instanceof Serializable)
    { values.addElement("root");
      values.addElement(root);
    stream.writeObject(values);
public void readExternal(ObjectInput stream) throws IOException
{ thisModel.removeAll();
    thisModel.setVisible(false);
    try
    { String title=stream.readUTF();
      rootNode = new DefaultMutableTreeNode(title);
      Vector values = (Vector)stream.readObject();
      int indexCounter = 0;
      int maxCounter = values.size();
      treeModel = new DefaultTreeModel(rootNode);
      if(indexCounter < maxCounter && values.elementAt(indexCounter).equals("root"))
      { TreeNode root = (TreeNode)values.elementAt(++indexCounter);
        treeModel = new DefaultTreeModel(root);
        indexCounter++;
      // kode for setting the tree start here
    catch (ClassNotFoundException e) {}
}Hope, this is to use :-)
Hi from
Super Bomba

Communication protocol between Admin Server and Managed Server

Hello - I am hoping someone can help me here to understand the communication protocols used in my setup.
Here is my understanding of the protocol that are used between each component.
End User <--->HTTPS<--->LoadBalancer Device<--->HTTPS<--->Web Server<---->HTTPS<--->WebLogic Server(Managed Server)<--->LDAP/JDBC<-->Data tier components
AdminServer<--->T3<--->Managed Server i.e. The communication protocol between Admin Server and Managed server is T3
The communication protocol between Managed Servers running in one cluster on two seperate machine is What?
Thank you.

Hello, interesting question.
In the documentation " [cluster multicast communication|http://download.oracle.com/docs/cd/E13222_01/wls/docs90/cluster/features.html#1007001] " don't specify the used protocol to pack the information for example in a session replication.
Although in a session replication all objects must be serializable i don't think rmi protocol is used.
I hope some expert give us some light in this issue :-)
http://download.oracle.com/docs/cd/E13222_01/wls/docs90/cluster/features.html#1007001

Re-Paired Cisco DMM and Cisco Show & Share

Hi ...
guys ... do anyone have experience to re-paired Cisco DMM and Cisco Show & Share ? I do re-paired it, but it doesn't success. First i pair Cisco Show and Share with Cisco DMS it success, but when i pair Cisco DMM with Cisco Show and Share it doesn't success (the proccess took so long about 30 minute i do ctrl C and it says failed to install certificate from Cisco Show and Share).
Anyone have idea ?
BR

Avoid Pairing Failures
•Pairing fails when you complete these steps in the wrong order. You must use AAI on your Cisco Cisco Show and Share appliance before you use AAI on your Cisco DMM appliance. Do not reverse this order or try to use AAI simultaneously on both appliances.
•Do not use the POP option on the pairing menu. Doing so may cause Cisco Show and Share to fail. If you accidently choose the POP option, you will need to re-pair the Cisco Show and Share and DMM appliances.
Pair Your Appliances
Procedure
Step 1 From the appliance that runs Cisco Show and Share 5.2:
a. Log in as admin to the Appliance Administration Interface (AAI).
b. Choose APPLIANCE_CONTROL > PAIR APPLIANCE.
c. Choose DMM.
Warning Do not choose any other option than DMM.
d. Enter the fully-qualified domain name (FQDN) for your Cisco DMM appliance.
This is the DNS name. Do not enter an IP address.
e. Press Enter.
Your Cisco Show and Share appliance receives and successfully imports a digital certificate from your Cisco DMM appliance.
Step 2 From the appliance that runs Cisco Digital Media Manager 5.2:
a. Log in as admin to the Appliance Administration Interface (AAI).
b. Choose APPLIANCE_CONTROL > PAIR APPLIANCE.
c. Choose SHOW_AND_SHARE.
Warning Do not choose any other option than SHOW_AND_SHARE.
d. Enter the fully-qualified domain name (FQDN) for your Cisco Show and Share appliance.
This is the DNS name. Do not enter an IP address.
e. Press Enter.
Your Cisco DMM appliance receives and successfully imports a digital certificate from your Cisco Show and Share appliance.
See Cisco Link :
http://www.cisco.com/en/US/docs/video/digital_media_systems/5_x/5_2/dms/aai/administration/guide/pair.html

Connection Problems Between iChat 3 and iChat 4 Workaround

Maybe this info will help others:
iChat 4/Leopard users must initiate video chat to iChat 3/Tiger users:
I have discovered that if an iChat 4/Leopard user initiates the video chat to an iChat3/Tiger user, it works, but if the iChat3/Tiger user initiates the video chat with an iChat 4/Leopard user it fails with a message saying that the receiver declined the invitation (even if the receiver tried to accept). This happens on a LAN as well as across the Internet.
Likewise, to make conference video chats, make sure the iChat 4/Leopard user initiates, then adds the other parties.
This post is NOT about iChat Server, although the problem occurs there too. If you are using iChat Server (part of OSX Server) see http://discussions.apple.com/thread.jspa?messageID=5995966 ).
Hope this helps.
ppj

Hey.
I found how to work around combatible problems between 1.3 and 1.4. For user, that want to save thier DynamicTree.java (http://java.sun.com/docs/books/tutorial/uiswing/components/example-swing/index.html)
Use follow code (I using Externalizable):
protected DefaultMutableTreeNode rootNode=null;
protected DefaultTreeModel treeModel=null;
public void writeExternal(ObjectOutput stream) throws IOException
{ stream.writeUTF(rootNode.toString());
    Vector values = new Vector();
    Object root = treeModel.getRoot();
    // Save the root, if its Serializable.
    if(root != null && root instanceof Serializable)
    { values.addElement("root");
      values.addElement(root);
    stream.writeObject(values);
public void readExternal(ObjectInput stream) throws IOException
{ thisModel.removeAll();
    thisModel.setVisible(false);
    try
    { String title=stream.readUTF();
      rootNode = new DefaultMutableTreeNode(title);
      Vector values = (Vector)stream.readObject();
      int indexCounter = 0;
      int maxCounter = values.size();
      treeModel = new DefaultTreeModel(rootNode);
      if(indexCounter < maxCounter && values.elementAt(indexCounter).equals("root"))
      { TreeNode root = (TreeNode)values.elementAt(++indexCounter);
        treeModel = new DefaultTreeModel(root);
        indexCounter++;
      // kode for setting the tree start here
    catch (ClassNotFoundException e) {}
}Hope, this is to use :-)
Hi from
Super Bomba

IChat - compatibility problems between v2.1 and v3.1

Hi,
I now have the new iMac Intel with iChat 3.1. I am trying to use it with a friend who has OS 10.3.9 with iChat 2.1.
I can see and hear him, but he can only hear me.
Is there a compatiliby problems between v2.1 and v.3.1 or it is just a configu problems?
Thanks a lot for any information
Bruno

Most likely cause is that you haven't updated the ProApplication Support file. Check here:
http://www.apple.com/support/downloads/proapplicationsupport31macosx104.html

VLAN problems with SG200-8P and Cisco ASA 5505 (Sec Plus license)

Hi, I've been pulling my hair out trying to get simple vlan trunking working between these devices.
Basically, no clients on VLAN 99 (guest) will receive DHCP ip addresses when plugged into the SG200. I have the SG200<>ASA VLAN trunk configured correctly, as I know it, and I've tried numerous variations (set trunk as general tag/untagged, etc., set the ap port to general tag/untag, etc). Both AP's work properly when connected to the ASA e0/3 port but either will only pull the "inside" VLAN dhcp address when connected to the SG200 switch
VLAN 1 - inside (has separate dhcp scope assigned by ASA)
VLAN 99 - guest (has separate dhcp scope assigned by ASA)
SG200
purpose
ASA 5505 (Sec Plus license)
purpose
g2
Trunk 1UP,99T
Ubiquiti AP (VLAN 1 works, VLAN 99 does not
g3
Access port 99T
vlan 99 does not work
g8
Trunk 1UP, 99T
< Trunk between switch and ASA >
Int e0/2
switchport trunk allowed vlan 1,99
switchport trunk native vlan 1
switchport mode trunk
Int e0/3
switchport trunk allowed vlan 1,99
switchport trunk native vlan 1
switchport mode trunk
Second ubiquiti AP
Both VLAN 1 and VLAN 99 clients work properly

Frustrated - yes. Confused - maybe not as much, but I could have put some more effort into the overall picture.
There are two VLANs (1 - native) and (99 - guest). There is a trunk port between the SG200 and the ASA configured as 1-untagged 99 - tagged.
No clients connected to the SG200 on VLAN 99 are able to access the ASA VLAN 99 using either a static VLAN IP address or DHCP. The problem occurs whether I configure the SG200 with an access port 99-tagged or Trunk port 1UP, 99T or general port 1U, 99UP or any combination thereof.
Anything connected to the SG200 on the native VLAN works properly.
Anything connected to the ASA VLANs (1 or 99) works properly
I have not yet tried to see what the switch is doing with the VLAN tags but I suspect I have some mismatch with the Linksys/Cisco SG200 way of setting up a VLAN and how traditional Cisco switches work.
I was hoping someone with a working SG200 - Cisco ASA setup could share their port/trunk/VLAN settings or perhaps point me in the right direction.
SG200 g2 - trunk port (1UP, 99T) -- Access Point
SG200 g2 - access port (99U)
SG200 g8 - trunk port (1UP, 99T) connected to ASA5505 e0/3
ASA5505 e0/3 (switchport trunk allowed vlan 1,99, switchport trunk native vlan 1, switchport mode trunk)
Thanks,

Communication problem between Cisco 3560 and Cisco SG300.

Similar Messages

Maybe you are looking for