Config certificate and log issues
I config certificate and use it to connect ipsec vpn ， I just config
jinan-neusoft(config)#ip domain-name neusoft.com
jinan-neusoft(config)#crypto key generate rsa general-keys
The name for the keys will be: jinan-neusoft.neusoft.com
Choose the size of the key modulus in the range of 360 to 4096 for your
General Purpose Keys. Choosing a key modulus greater than 512 may take
a few minutes.
How many bits in the modulus [512]:
% Generating 512 bit RSA keys, keys will be non-exportable...
[OK] (elapsed time was 0 seconds)
jinan-neusoft(config)#
Nov 16 01:05:44.435: RSA key size needs to be atleast 768 bits for ssh version 2
jinan-neusoft(config)#
Nov 16 01:05:44.435: %SSH-5-ENABLED: SSH 1.5 has been enabled
jinan-neusoft(config)#crypto pki trustpoint CA1
jinan-neusoft(ca-trustpoint)# enrollment url http://59.44.43.217:80
jinan-neusoft(ca-trustpoint)# revocation-check crl
jinan-neusoft(ca-trustpoint)# rsakeypair DMVPN-SY-KEY
jinan-neusoft(ca-trustpoint)# auto-enrol
jinan-neusoft(config)#crypto pki authenticate CA1
Certificate has the following attributes:
Fingerprint MD5: D5F9D56B 4D9A4260 43F21D39 811D7AD5
Fingerprint SHA1: 1E49B228 DD57F4DB 43DD2C2F 03870C18 840DA12A
% Do you accept this certificate? [yes/no]: y
Trustpoint CA certificate accepted.
then I have log issues like below ，even I config auto-enroll , I don t get certificate pending information from my certificate server ，
my device is C3925 and ios is c3900-universalk9-mz.SPA.151-4.M4.bin ，how to deal with it ，top players ， THX~~~~
Nov 16 01:07:54.871: %PKI-6-CERTRENEWAUTO: Renewing the router certificate for trustpoint CA1
Nov 16 01:07:54.951: %CRYPTO-6-AUTOGEN: Generated new 512 bit key pair
Nov 16 01:07:55.115: CRYPTO_PKI: Certificate Request Fingerprint MD5: 939AF8C1 854DDA90 8FE03058 5635468F
Nov 16 01:07:55.115: CRYPTO_PKI: Certificate Request Fingerprint SHA1: 50F869D2 C0814317 7EB2ECC9 90461F3A 353E7089
Nov 16 01:07:55.119: %SYS-3-INVMEMINT: Invalid memory action (malloc) at interrupt level
-Traceback= 5564384z 68B3034z 945A8D0z 6D05DF0z 6
jinan-neusoft(config)#D05F70z 6D06B50z 6D07268z 6D43018z 6D25044z 6D1988Cz 6D4CCE0z 91F0154z 91F0CC4z 91F0DA4z 4ACB9F4z 4127784z
Nov 16 01:07:55.119: %SYS-2-MALLOCFAIL: Memory allocation of 40 bytes failed from 0x6D05DEC, alignment 0
Pool: Processor Free: 731143916 Cause: Interrupt level allocation
Alternate Pool: None Free: 0 Cause: Interrupt level allocation
-Process= "<interrupt level>", ipl= 3
-Traceback= 5564384z 6892328z 68B3064z 945A8D0z 6D05DF0z 6D05F70z 6D06B50z 6D07268z 6D43018z 6D25044z 6D1988Cz 6D4CCE0z 91F0154z 91F0CC4z 91F0DA4z 4ACB9F4z
Nov 16 01:07:55.119: %SYS-3-INVMEMINT: Invalid memory action (malloc) at interrupt level
-Traceback= 5564384z 68B3034z 945A8D0z 6D05DF0z 6D05F70z 6D06B50z 6D07268z 6D4308Cz 6D25044z 6D1988Cz 6D4CCE0z 91F0154z 91F0CC4z 91F0DA4z 4ACB9F4z 4127784z
jinan-neusoft(config)#
Nov 16 01:08:09.719: %PKI-6-CERTRENEWAUTO: Renewing the router certificate for trustpoint CA1
Nov 16 01:08:09.879: CRYPTO_PKI: Certificate Request Fingerprint MD5: 939AF8C1 854DDA90 8FE03058 5635468F
Nov 16 01:08:09.879: CRYPTO_PKI: Certificate Request Fingerprint SHA1: 50F869D2 C0814317 7EB2ECC9 90461F3A 353E7089
jinan-neusoft(config)#
Nov 16 01:08:09.883: %SYS-3-INVMEMINT: Invalid memory action (malloc) at interrupt level
-Traceback= 5564384z 68B3034z 945A8D0z 6D05DF0z 6D05F70z 6D06B50z 6D07268z 6D43018z 6D25044z 6D1988Cz 6D4CCE0z 91F0154z 91F0CC4z 91F0DA4z 4ACB9F4z 4127784z
Nov 16 01:08:09.883: %SYS-3-INVMEMINT: Invalid memory action (malloc) at interrupt level
-Traceback= 5564384z 68B3034z 945A8D0z 6D05DF0z 6D05F70z 6D06B50z 6D07268z 6D4308Cz 6D25044z 6D1988Cz 6D4CCE0z 91F0154z 91F0CC4z 91F0DA4z 4ACB9F4z 4127784z
jinan-neusoft(config)# Nov 16 01:07:54.871: %PKI-6-CERTRENEWAUTO: Renewing the router certificate for trustpoint CA1
Nov 16 01:07:54.951: %CRYPTO-6-AUTOGEN: Generated new 512 bit key pair
Nov 16 01:07:55.115: CRYPTO_PKI: Certificate Request Fingerprint MD5: 939AF8C1 854DDA90 8FE03058 5635468F
Nov 16 01:07:55.115: CRYPTO_PKI: Certificate Request Fingerprint SHA1: 50F869D2 C0814317 7EB2ECC9 90461F3A 353E7089
Nov 16 01:07:55.119: %SYS-3-INVMEMINT: Invalid memory action (malloc) at interrupt level
-Traceback= 5564384z 68B3034z 945A8D0z 6D05DF0z 6
jinan-neusoft(config)#D05F70z 6D06B50z 6D07268z 6D43018z 6D25044z 6D1988Cz 6D4CCE0z 91F0154z 91F0CC4z 91F0DA4z 4ACB9F4z 4127784z
Nov 16 01:07:55.119: %SYS-2-MALLOCFAIL: Memory allocation of 40 bytes failed from 0x6D05DEC, alignment 0
Pool: Processor Free: 731143916 Cause: Interrupt level allocation
Alternate Pool: None Free: 0 Cause: Interrupt level allocation
-Process= "<interrupt level>", ipl= 3
-Traceback= 5564384z 6892328z 68B3064z 945A8D0z 6D05DF0z 6D05F70z 6D06B50z 6D07268z 6D43018z 6D25044z 6D1988Cz 6D4CCE0z 91F0154z 91F0CC4z 91F0DA4z 4ACB9F4z
Nov 16 01:07:55.119: %SYS-3-INVMEMINT: Invalid memory action (malloc) at interrupt level
-Traceback= 5564384z 68B3034z 945A8D0z 6D05DF0z 6D05F70z 6D06B50z 6D07268z 6D4308Cz 6D25044z 6D1988Cz 6D4CCE0z 91F0154z 91F0CC4z 91F0DA4z 4ACB9F4z 4127784z
jinan-neusoft(config)#
Nov 16 01:08:09.719: %PKI-6-CERTRENEWAUTO: Renewing the router certificate for trustpoint CA1
Nov 16 01:08:09.879: CRYPTO_PKI: Certificate Request Fingerprint MD5: 939AF8C1 854DDA90 8FE03058 5635468F
Nov 16 01:08:09.879: CRYPTO_PKI: Certificate Request Fingerprint SHA1: 50F869D2 C0814317 7EB2ECC9 90461F3A 353E7089
jinan-neusoft(config)#
Nov 16 01:08:09.883: %SYS-3-INVMEMINT: Invalid memory action (malloc) at interrupt level
-Traceback= 5564384z 68B3034z 945A8D0z 6D05DF0z 6D05F70z 6D06B50z 6D07268z 6D43018z 6D25044z 6D1988Cz 6D4CCE0z 91F0154z 91F0CC4z 91F0DA4z 4ACB9F4z 4127784z
Nov 16 01:08:09.883: %SYS-3-INVMEMINT: Invalid memory action (malloc) at interrupt level
-Traceback= 5564384z 68B3034z 945A8D0z 6D05DF0z 6D05F70z 6D06B50z 6D07268z 6D4308Cz 6D25044z 6D1988Cz 6D4CCE0z 91F0154z 91F0CC4z 91F0DA4z 4ACB9F4z 4127784z
jinan-neusoft(config)#
I do not have the answer but have exactly the same issue, looks as if it is a bug of some kind :
Cisco CISCO3945-CHASSIS (revision 1.0) with C3900-SPE150/K9 with 980992K/67584K bytes of memory.
Processor board ID FCZ163371P3
6 FastEthernet interfaces
3 Gigabit Ethernet interfaces
1 terminal line
1 Virtual Private Network (VPN) Module
DRAM configuration is 72 bits wide with parity enabled.
255K bytes of non-volatile configuration memory.
250880K bytes of ATA System CompactFlash 0 (Read/Write)
System image file is "flash0:c3900-universalk9-mz.SPA.151-4.M4.bin"
Nov 16 07:37:16.611: CRYPTO_PKI: Signature Certificate Request Fingerprint MD5: 358FF778 7C2E66AE 895BF088 BF022442
.Nov 16 07:37:16.615: CRYPTO_PKI: Signature Certificate Request Fingerprint SHA1: 5F7A4300 20B62132 83D08C6E 2D315DF4 51EFE94D
.Nov 16 07:37:16.623: %SYS-3-INVMEMINT: Invalid memory action (malloc) at interrupt level
-Traceback= 5564384z 68B3034z 945A8D0z 6D05DF0z 6D05F70z 6D06B50z 6D07268z 6D4308Cz 6D25044z 6D1988Cz 6D4CCE0z 91F0154z 91F0CC4z 91F0DA4z 4ACB9F4z 412
7784z
.Nov 16 07:37:16.623: %SYS-2-MALLOCFAIL: Memory allocation of 72 bytes failed from 0x6D05DEC, alignment 0
Pool: Processor Free: 704933204 Cause: Interrupt level allocation
Alternate Pool: None Free: 0 Cause: Interrupt level allocation
-Process= "", ipl= 3
-Traceback= 5564384z 6892328z 68B3064z 945A8D0z 6D05DF0z 6D05F70z 6D06B50z 6D07268z 6D4308Cz 6D25044z 6D1988Cz 6D4CCE0z 91F0154z 91F0CC4z 91F0DA4z 4AC
B9F4z Nov 16 07:37:16.611: CRYPTO_PKI: Signature Certificate Request Fingerprint MD5: 358FF778 7C2E66AE 895BF088 BF022442
.Nov 16 07:37:16.615: CRYPTO_PKI: Signature Certificate Request Fingerprint SHA1: 5F7A4300 20B62132 83D08C6E 2D315DF4 51EFE94D
.Nov 16 07:37:16.623: %SYS-3-INVMEMINT: Invalid memory action (malloc) at interrupt level
-Traceback= 5564384z 68B3034z 945A8D0z 6D05DF0z 6D05F70z 6D06B50z 6D07268z 6D4308Cz 6D25044z 6D1988Cz 6D4CCE0z 91F0154z 91F0CC4z 91F0DA4z 4ACB9F4z 412
7784z
.Nov 16 07:37:16.623: %SYS-2-MALLOCFAIL: Memory allocation of 72 bytes failed from 0x6D05DEC, alignment 0
Pool: Processor Free: 704933204 Cause: Interrupt level allocation
Alternate Pool: None Free: 0 Cause: Interrupt level allocation
-Process= "", ipl= 3
-Traceback= 5564384z 6892328z 68B3064z 945A8D0z 6D05DF0z 6D05F70z 6D06B50z 6D07268z 6D4308Cz 6D25044z 6D1988Cz 6D4CCE0z 91F0154z 91F0CC4z 91F0DA4z 4AC
B9F4z
Similar Messages
-
Hi All,
I have previously been a user of captivate 4 and have just downloaded the trial of captivate 6 at my new place of work with a view to investing in it for our e-learning going forward.
I have written a small trial module and have a couple of issues - have googled etc but cannot find the answer so here goes....
Certificate - in captivate 4 i was able to insert the certifcate widget and it would pull the name of the learner through from a variable V_Name. I have tried this in v6 and it does not bring the name onto the certificate - ive used V_Name and just tried User_Name as variables but still no name appears on the certifate.
I have also tried to get it too display the name of my module in the 'has taken the course' section of the certifcate - in captivate 4 i manually entered that onto the widget in the cert slide which worked fine - in v6 that is not an option... i have added a variable with the name of the module but that has not worked. - any ideas would be welcome...
Also,
Images as Red Boxes
I have a problem with some of my images showing as red boxes on the published scorm package when it is played back through moodle. We've run it on 2 pcs on the network with the same issue - flash player is v10 and im publishing it in flash player 10. These images work absolutely fine on my mac in preview mode. Very strange. Also, I have some of the images which are red boxes in the main slideshow but appear absolutely fine on a question slide?? Again any ideas would be much appreciated.Hi Lilybiri.
Thanks for the reply.
I tried the variable v_Name (lowercase v) and that has worked for the certifcate - still not too sure how to get the course name populated?
The images are mainly jpegs and png's and bitmaps. I just checked the slide quality and it was on low 8 bit - so have changed that. Cant see an option for transparency...I'll try it with the slide quality changed and see what happens.
Whilst you're about - can you help with a question about text entry boxes please? I've set up a TEB at the beginning for the learner to type in their learning objectives - the key things that they want to get from the module. I made 3 TEBs so that they could write a max of 3 objectives. I've associated the TEB with the following $$TTextEntryItem1Var$$ but it only displays around 13 characters of text?
Thanks,
Alex -
DPS App Builder - certificates and account issue
Hi,
I'm working on an App for a client who's going to use it internally with his employees.
My company has an Enterprise account and I'm a member of it.
Working with the Creative Cloud - not using the same email address as the Admin of the Enterprise account.
I finished creating the InDesign files, the certificates etc. I can launch "Create the app" in InDesign and fill the first steps in DPS App Builder but when I try to add the certificates it says:
"App ID inside the mobileprovision file contains "*". This type of mobileprovision app ID is only applicable for Enterprise signed builds. You will need to re-generate this file with a valid app ID."
Can the problem comes from the fact that I'm not logged into CC with the Enterprise Admin email address? Or because I'm set in the Enterprise Account as a member and not Admin?
Thank you for your help!
Sophie_HHI figured it out. I was confusing the p12 file for the push notifications with the original developer p12 file. All fixed.
Rob -
What is the current schedule for 6.1.2 and will it fix the Exchange transaction log issue in 6.1?
Just spent the entire night with virtually no sleep with our firm's group of IT engineers trying to keep our Exchange system online due to massive transaction log growth. Confirmed the issue related to 6.1 calendar bug with Activesync. The workarounds are not practical for large groups of users who depend on their mobile devices for work. Our users have no way of knowing that they are causing an issue so the Apple guidance isnt terribly useful to communicate to 1000 users. When can we expect a resolution? The problem is only going to get worse as more and more users hit the bug. Does anyone know if the issue will resolve as soon as someone installs the 6.1.2 update, assuming that has the fix. Im not trying to bash anyone but this is a very serious problem in enterprise deployments.
The update was released some time today. 6.1.2 appears to specifically fix the Exchange issue causing excess comms and logging issues. However, although the update is available i do not see the notification badge on the Settings icon. Is this controlled by Apple or is there a user setting i am missing somewhere? I would prefer that all users see the badge to expedite user action.
-
Unable to log into iMessage and intermittent issues with FaceTime
Late 2011 MacBook Pro, OS X 10.8.4. I'm an admin level Windows guy but a relatively new (and otherwise very pleased) convert to Mac OS.
This morning Messages started repeatedly prompting me for my iMessage password and FaceTime has starting working only intermittently. Both work fine from my iPad and iPhone 5. Both have been working from my MacBook Pro for months.
This morning when I tried to fire up Messages on the MacBook I got an error saying "The server encountered an error processing registration". After doing some Googling, I noticed that many folks said that when they had this problem they also had an issue with FaceTime. I confirmed that FaceTime was indeed giving me the same error as iMessage. After trying some solutions from past threads that didn't work, I rebooted. Now instead of throwing an error, Messages just keeps asking me for my iMessage password again and again. FaceTime works occasionally but sometimes when I get a call and click answer, I get "call failed" as my iPhone and iPad continue to ring and then I'm asked to re-enter my password on the MacBook. If I enter my password it just sits and spins. If i quit FaceTime and start it again, it'll usually log in successfully but calls may or may not work (following the same pattern I just mentioned).
The odd thing to me is that when I tested FaceTime on my iPad, I got notifications on my iPad and iPhone and my primary and alternate email address were now registered with FaceTime. They have been for over a year so I'm not sure why I'm getting those notifications again.
I'm able to log into the Mac App store without a problem using the same AppleID
What I've tried so far based on Google results:
1. In Keychain Access, reset my default keychain - No improvement
2. In Keychain Access, selected Keychain First Aid, repaired and verified - No improvement
3. On my iPad, turned iMessage off and back on - No improvement, though iMessage on the iPad still works fine
4. Confirmed that my primary and secondary AppleID email addresses and password are correct. The email address associated with my AppleID is not associated with any other AppleIDs.
Thanks!This could be a complicated problem to solve, as there are many possible causes for it. Test after taking each of the following steps that you haven't already tried. Back up all data before making any changes.
Before proceeding, test on another network, if possible. That could be a public Wi-Fi hotspot, if your computer is portable, or a cellular network if you have a mobile device that can share its Internet connection. If you find that iMessage works on the other network, the problem is in your network or at your ISP, not in your computer.
Step 1
Check the status of the service. If the service is down, wait tor it to come back up. There may be a localized outage, even if the status indicator is green.
Step 2
Restart your broadband device and your router, if different. You may have to skip this step if you don't control those devices.
Step 3
From the menu bar, select
▹ About This Mac
Below the "OS X" legend in the window that opens, the OS version appears. Click the version line twice to display the serial number. If the number is missing or obviously invalid, take the machine to an Apple Store or other authorized service center to have the problem corrected.
Step 4
Take the steps suggested in this support article. If you don't understand some of the steps or can't carry them out, ask for guidance.
Step 5
From the menu bar, select
▹ System Preferences ▹ Network
If the preference pane is locked, click the lock icon in the lower left corner and enter your password to unlock it. Then click the Advanced button and select the Proxies tab. If the box marked SOCKS Proxy is checked, uncheck it. You don’t need to change any other settings in the window. Click OK and then Apply. Test.
The result may be that you can't connect to the Internet at all. Revert the change if that happens, or if iMessage still doesn't work. Remember that you must Apply any changes you make in the preference pane before they take effect.
Step 6
Select from the menu bar
▹ System Preferences… ▹ Flash Player ▹ Storage
and click
Block all sites from storing information on this computer
Close the preference pane.
Step 7
Enable guest logins* and log in as Guest. Don't use the Safari-only “Guest User” login created by “Find My Mac.”
While logged in as Guest, you won’t have access to any of your personal files or settings. Applications will behave as if you were running them for the first time. Don’t be alarmed by this; it’s normal. If you need any passwords or other personal data in order to complete the test, memorize, print, or write them down before you begin.
Test while logged in as Guest. After testing, log out of the guest account and, in your own account, disable it if you wish. Any files you created in the guest account will be deleted automatically when you log out of it.
*Note: If you’ve activated “Find My Mac” or FileVault, then you can’t enable the Guest account. The “Guest User” login created by “Find My Mac” is not the same. Create a new account in which to test, and delete it, including its home folder, after testing.
If iMessage worked in the guest account, stop here and post your results.
Step 8
Boot in safe mode and log in. Note: If FileVault is enabled on some models, or if a firmware password is set, or if the boot volume is a software RAID, you can’t do this. Ask for further instructions.
Safe mode is much slower to boot and run than normal, and some things won’t work at all, including Wi-Fi on certain iMacs. The next normal boot may also be somewhat slow.
The login screen appears even if you usually log in automatically. You must know your login password in order to log in. If you’ve forgotten the password, you will need to reset it before you begin.
Test while in safe mode. After testing, reboot as usual (i.e., not in safe mode) and test again.
If iMessage worked in safe mode, but didn't work when you booted out of safe mode, stop here and post your results.
Step 9
Reset the NVRAM.
Step 10
Reinstall OS X.
Step 11
If none of the above steps resolves the issue, make a "Genius" appointment at an Apple Store, or contact Apple Support. -
Logging into ITunes and update issues
i have just been through the saga of restoring a backup of my 4S phone to my new iPhone 6 Plus - took over a day but using the support community eventually found a way to do it. I then wanted to use Airplay to show a video on my iPhone 6 Plus via my Apple TV - the results were poor and eventually no video would work at all. The Apple TV also reported it was not logged into iTunes. Every attempt to log into ITunes failed. I tried connecting via an Ethernet rather than wifi but it was not the problem. I could see that there was a Apple TV upgrade available so I started to upgrade - nothing happened with no progress bar activity showing and again looked like a failed connection. I persisted with trying and finally just left it 'upgrading' and eventually the progress bar showed the update would take 7 HOURS!
So I left the Apple TV updating and went to bed. This morning I find the Apple TV has updated and logged into ITunes.
IF Apple came clean I am sure they would admit that the IOS 8 upgrade at the same time as introducing new iPhones has this time completely screwed their servers. The problem I had with restoring a backup to my new iPhone I think was mainly the stupid checked box in iTunes for synch all iPhotos to the phone - nearly 8,000 of them!
WHy why on earth did Apple not introduce IOS 8 FIRST then after settling down introduce the new phones. I doubt that Apple will fully recover from this (and bendy phones) adverse publicity and is all down to being too eager to tie everything in with a much publicised conference launch.Ok, time to report the issue here:
iTunes Store Support
http://www.apple.com/emea/support/itunes/contact.html -
RMAN BACKUPS AND ARCHIVED LOG ISSUES
제품 : RMAN
작성날짜 : 2004-02-17
RMAN BACKUPS AND ARCHIVED LOG ISSUES
=====================================
Scenario #1:
1)RMAN이 모든 archived log들을 삭제할 때 실패하는 경우.
database는 두 개의 archive destination에 archive file을 생성한다.
다음과 같은 스크립트를 수행하여 백업후에 archived redo logfile을 삭제한다.
run {
allocate channel c1 type 'sbt_tape';
backup database;
backup archivelog all delete input;
Archived redo logfile 삭제 유무를 확인하기 위해 CROSSCHECK 수행시 다음과
같은 메시지가 발생함.
RMAN> change archivelog all crosscheck;
RMAN-03022: compiling command: change
RMAN-06158: validation succeeded for archived log
RMAN-08514: archivelog filename=
/oracle/arch/dest2/arcr_1_964.arc recid=19 stamp=368726072
2) 원인분석
이 문제는 에러가 아니다. RMAN은 여러 개의 arhive directory중 하나의
directoy안에 있는 archived file들만 삭제한다. 그래서 나머지 directory안의
archived log file들은 삭제되지 않고 남게 되는 것이다.
3) 해결책
RMAN이 강제로 모든 directory안의 archived log file들을 삭제하게 하기 위해서는
여러 개의 채널을 할당하여 각 채널이 각 archive destination안의 archived file을
백업하고 삭제하도록 해야 한다.
이것은 아래와 같이 구현될 수 있다.
run {
allocate channel t1 type 'sbt_tape';
allocate channel t2 type 'sbt_tape';
backup
archivelog like '/oracle/arch/dest1/%' channel t1 delete input
archivelog like '/oracle/arch/dest2/%' channel t2 delete input;
Scenario #2:
1)RMAN이 archived log를 찾을 수 없어 백업이 실패하는 경우.
이 시나리오에서 database를 incremental backup한다고 가정한다.
이 경우 RMAN은 recover시 archived redo log대신에 incremental backup을 사용할
수 있기 때문에 백업 후 모든 archived redo log를 삭제하기 위해 OS utility를 사용한다.
그러나 다음 번 backup시 다음과 같은 Error를 만나게 된다.
RMAN-6089: archive log NAME not found or out of sync with catalog
2) 원인분석
이 문제는 OS 명령을 사용하여 archived log를 삭제하였을 경우 발생한다. 이때 RMAN은
archived log가 삭제되었다는 것을 알지 못한다. RMAN-6089는 RMAN이 OS 명령에 의해
삭제된 archived log가 여전히 존재하다고 생각하고 백업하려고 시도하였을 때 발생하게 된다.
3) 해결책
가장 쉬운 해결책은 archived log를 백업할 때 DELETE INPUT option을 사용하는 것이다.
예를 들면
run {
allocate channel c1 type 'sbt_tape';
backup archivelog all delete input;
두 번째로 가장 쉬운 해결책은 OS utility를 사용하여 archived log를 삭제한 후에
다음과 같은 명령어를 RMAN prompt상에서 수행하는 것이다.
RMAN>allocate channel for maintenance type disk;
RMAN>change archivelog all crosscheck;
Oracle 8.0:
RMAN> change archivelog '/disk/path/archivelog_name' validate;
Oracle 8i:
RMAN> change archivelog all crosscheck ;
Oracle 9i:
RMAN> crosscheck archivelog all ;
catalog의 COMPATIBLE 파라미터가 8.1.5이하로 설정되어 있으면 RMAN은 찾을 수 없는
모든 archived log의 status를 "DELETED" 로 셋팅한다. 만약에 COMPATIBLE이 8.1.6이상으로
설정되어 있으면 RMAN은 Repository에서 record를 삭제한다.Very strange, I issue following command in RMAN on both primary and standby machine, but it they don't delete the 1_55_758646076.dbf, I find in v$archived_log, this "/home/oracle/app/oracle/dataguard/1_55_758646076.dbf" had already been applied.
RMAN> connect target /
RMAN> CONFIGURE ARCHIVELOG DELETION POLICY TO APPLIED ON ALL STANDBY;
old RMAN configuration parameters:
CONFIGURE ARCHIVELOG DELETION POLICY TO APPLIED ON ALL STANDBY;
new RMAN configuration parameters:
CONFIGURE ARCHIVELOG DELETION POLICY TO APPLIED ON ALL STANDBY;
new RMAN configuration parameters are successfully stored
RMAN>
---------------------------------------------------------------------------------- -
Hi,
Problem Description:
After installing my new product version, when user does log-off and log in again into admin account
or switch from admin account to non-admin account, PATH environment variable shows incorrect path of my product (previous product version’s path) using command prompt.
It seems windows refresh issue during session changes (log off and log in / switch from Admin to
Non-admin account).
Why PATH environment variable is not refresh immediately after log off and log in again or Switch
from admin to non-admin mode?.
Please see my thread for more details http://social.msdn.microsoft.com/Forums/vstudio/en-US/445ab42c-bdff-405a-8d53-558e1b6c7d34/path-environment-variable-issue-when-user-logoff-and-login-or-switch-from-admin-to-nonadmin?forum=windowsgeneraldevelopmentissues
Also submitted bug for this in connect.microsoft.com portal.In that it has lots of information
like problem statement, Reproduction steps and Expected Results.
Bug ID: 871782
Could you please any body help me for this?. your support will be appreciated.
Thanks,
MarichamyWhy PATH environment variable is not refresh immediately after log off and log in again or Switch
from admin to non-admin mode?.
I wouldn't have any expectation of what you are doing to work the way you expect. E.g. why is the %ABC% being replaced at all? There is some help about this ambiguous scenario in the cmd help...
/V:ON Enable delayed environment variable expansion using ! as the
delimiter. For example, /V:ON would allow !var! to expand the
variable var at execution time. The var syntax expands variables
at input time, which is quite a different thing when inside of a FOR
loop.
/V:OFF Disable delayed environment expansion.
So, what's the setting for the /V: switch that your users would be using? Perhaps you should be using the ! instead of the % for your ABC variable?
Oh. There's more below where I found that...
Delayed environment variable expansion is NOT enabled by default. You
can enable or disable delayed environment variable expansion for a
particular invocation of CMD.EXE with the /V:ON or /V:OFF switch. You
can enable or disable delayed expansion for all invocations of CMD.EXE on a
machine and/or user logon session by setting either or both of the
following REG_DWORD values in the registry using REGEDIT.EXE:
HKEY_LOCAL_MACHINE\Software\Microsoft\Command Processor\DelayedExpansion
and/or
HKEY_CURRENT_USER\Software\Microsoft\Command Processor\DelayedExpansion
to either 0x1 or 0x0. The user specific setting takes precedence over
the machine setting. The command line switches take precedence over the
registry settings.
In a batch file the SETLOCAL ENABLEDELAYEDEXPANSION or DISABLEDELAYEDEXPANSION
arguments takes precedence over the /V:ON or /V:OFF switch. See SETLOCAL /?
for details.
If delayed environment variable expansion is enabled, then the exclamation
character can be used to substitute the value of an environment variable
at execution time.
So, I guess the essence of your "bug" will boil down to whether you
need the feature to get the result you want and the
truth of that first sentence but it certainly looks like a "can of worms" to me. ; )
HTH
Robert Aldwinckle -
I have this all new ipad4 and recently it is having issues connecting to wifi and logging into mails
I'm experiencing troubles with my ipad connecting to wifi. It would detect even right passwords as wrong where in it would connect to open networks without any troubles. This thing is also happening with my mail login. I can't login into my other mail accounts other than icloud as it would detect password entered as wrong. I'm so sure that I typed the password right and there are issues with the keyboard either. I've always checked caps lock and language I'm using are appropriate and there are absolutely no flaws when I'm typing passwords. Please someone help me rectify this and also share it here if you're experiencing the same problem.
P.S. I've gone so far that even resetting didn't work.Some things to try first:
1. Turn Off your iPad. Then turn Off (disconnect power cord for 30 seconds or longer) the wireless router & then back On. Now boot your iPad. Hopefully it will see the WiFi.
2. Go to Settings>Wi-Fi and turn Off. Then while at Settings>Wi-Fi, turn back On and chose a Network.
3. Change the channel on your wireless router (Auto or Channel 6 is best). Instructions at http://macintoshhowto.com/advanced/how-to-get-a-good-range-on-your-wireless-netw ork.html
4. Go into your router security settings and change from WEP to WPA with AES.
5. Renew IP Address: (especially if you are droping internet connection)
• Launch Settings app
• Tap on Wi-Fi
• Tap on the blue arrow of the Wi-Fi network that you connect to from the list
• In the window that opens, tap on the Renew Lease button
6. Potential Quick Fixes When Your iPad Won’t Connect to Your Wifi Network
http://ipadinsight.com/ipad-tips-tricks/potential-quick-fixes-when-your-ipad-won t-connect-to-your-wifi-network/
~~~~~~~~~~~~~~~~~~~~~~~~~
iOS 6 Wifi Problems/Fixes
Wi-Fi Fix for iOS 6
https://discussions.apple.com/thread/4823738?tstart=240
How To: Workaround iPad Wi-Fi Issues
http://www.theipadfan.com/workaround-ipad-wifi-issues/
Another Fix For iOS 6 WiFi Problems
http://tabletcrunch.com/2012/10/27/fix-ios-6-wifi-problems-ssid/
Wifi Doesn't Connect After Waking From Sleep - Sometimes increasing screen brightness prevents the failure to reconnect after waking from sleep. According to Apple, “If brightness is at lowest level, increase it by moving the slider to the right and set auto brightness to off.”
Fix For iOS 6 WiFi Problems?
http://tabletcrunch.com/2012/09/27/fix-ios-6-wifi-problems/
Did iOS 6 Screw Your Wi-Fi? Here’s How to Fix It
http://gizmodo.com/5944761/does-ios-6-have-a-wi+fi-bug
How To Fix Wi-Fi Connectivity Issue After Upgrading To iOS 6
http://www.iphonehacks.com/2012/09/fix-wi-fi-connectivity-issue-after-upgrading- to-ios-6.html
iOS 6 iPad 3 wi-fi "connection fix" for netgear router
http://www.youtube.com/watch?v=XsWS4ha-dn0
Apple's iOS 6 Wi-Fi problems
http://www.zdnet.com/apples-ios-6-wi-fi-problems-linger-on-7000004799/
~~~~~~~~~~~~~~~~~~~~~~~
How to Boost Your Wi-Fi Signal
http://ipad.about.com/od/iPad_Troubleshooting/a/How-To-Boost-Your-Wi-Fi-Signal.h tm
Troubleshooting a Weak Wi-Fi Signal
http://ipad.about.com/od/iPad_Troubleshooting/a/Troubleshooting-A-Weak-Wi-Fi-Sig nal.htm
How to Fix a Poor Wi-Fi Signal on Your iPad
http://ipad.about.com/od/iPad_Troubleshooting/a/How-To-Fix-A-Poor-Wi-Fi-Signal-O n-Your-iPad.htm
iOS Troubleshooting Wi-Fi networks and connections http://support.apple.com/kb/TS1398
iPad: Issues connecting to Wi-Fi networks http://support.apple.com/kb/ts3304
WiFi Connecting/Troubleshooting http://www.apple.com/support/ipad/wifi/
How to Fix: My iPad Won't Connect to WiFi
http://ipad.about.com/od/iPad_Troubleshooting/ss/How-To-Fix-My-Ipad-Wont-Connect -To-Wi-Fi.htm
iOS: Connecting to the Internet http://support.apple.com/kb/HT1695
iOS: Recommended settings for Wi-Fi routers and access points http://support.apple.com/kb/HT4199
How to Quickly Fix iPad 3 Wi-Fi Reception Problems
http://osxdaily.com/2012/03/21/fix-new-ipad-3-wi-fi-reception-problems/
iPad Wi-Fi Problems: Comprehensive List of Fixes
http://appletoolbox.com/2010/04/ipad-wi-fi-problems-comprehensive-list-of-fixes/
Connect iPad to Wi-Fi (with troubleshooting info)
http://thehowto.wikidot.com/wifi-connect-ipad
Fix iPad Wifi Connection and Signal Issues http://www.youtube.com/watch?v=uwWtIG5jUxE
Fix Slow WiFi Issue https://discussions.apple.com/thread/2398063?start=60&tstart=0
How To Fix iPhone, iPad, iPod Touch Wi-Fi Connectivity Issue http://tinyurl.com/7nvxbmz
Unable to Connect After iOS Update - saw this solution on another post.
https://discussions.apple.com/thread/4010130
Note - When troubleshooting wifi connection problems, don't hold your iPad by hand. There have been a few reports that holding the iPad by hand, seems to attenuate the wifi signal.
Wi-Fi or Bluetooth settings grayed out or dim
http://support.apple.com/kb/TS1559
~~~~~~~~~~~~~~~
If any of the above solutions work, please post back what solved your problem. It will help others with the same problem.
Cheers, Tom -
Erratic Mouse and Keyboard issues...with weird console log...
Hello All,
I recently installed Snow Leopard on my 2x2.8 Quad Core Mac Pro following a boot drive melt down. Apple replaced the drive via Apple Care and I re-installed all my apps. The only additional item of note is I have Lycom SATA four port card that required a driver update.
Since setting up this machine with the new OS I am having massive issues with keyboard lag, erratic mouse movement and intermittent freezing.
I've run tech tools deluxe and everything passes with that app. I cant find the original install disks so running AHT on this machine isn't going to happen.
I've tried with and without the driver and the issue seems to still be there.
On a whim I opened console and I am seeing this message hundreds and hundreds of times over...
8/8/10 2:21:11 PM com.apple.launchd[1] (org.xinetd.xinetd[2652]) Exited with exit code: 1
8/8/10 2:21:11 PM com.apple.launchd[1] (org.xinetd.xinetd) Throttling respawn: Will start in 10 seconds
8/8/10 2:21:21 PM com.apple.launchd[1] (org.xinetd.xinetd[2655]) posix_spawn("xinetd", ...): No such file or directory
Anyone got any thoughts on this?
Thanks,
ScottJstys92,
Heat? Motherboard? Sounds like hardware since it's across Operating systems...
If you have a warranty, this is the time to call HP.
HP Product Warranty Check
Contact HP - Worldwide
Contact HP - USA
If not, I still think you have a HW issue. It is relatively consistant, too. Like something is breaking down - physically. Not a disk - BIOS... notherboard... something that holds everything together.
Computers are not supposed to warm up and then start doing whatever they want.
We do not live it in that world, at least not yet.
===========================================================================
You could run some Diagnostics. The UEFI Diagnostics, if you don't already have them on your system, are very good and provide a decent "human interface".
HP System Diagnostics (UEFI)
Description: This package provides the HP System Diagnostics (UEFI) for the supported notebook/laptop models and operating systems. HP System Diagnostics is a UEFI-based hardware diagnostics program that is used to validate if a system is functional enough to start up the operating system. The diagnostics are accessed during startup by pressing F2 immediately after power on.
=========================================================================
Good Luck!
We work hard to help!
Whenever you see a Helpful Post - Click the Kudos Star on the Left as Thanks!
Did this Post solve your problem? Mark it “Accept as Solution”!
Note: You can find the “Accept as Solution” box on threads started by you.
2012 Year of the Dragon!
Kind Regards,
Dragon-Fur -
Failed Hardware Scan and other issues E440
Hi all,
This is probably more rant than anything, but I wanted to give a heads up to others too.
I have a ThinkPad E440 that is a year old. From the very first time I turned it on, there have been issues. The first hardware scan (via Lenovo Solution Center - LSC) showed a warning for the Intel Dual Band Wireless-AC 7260 Local Connection Test. There were also tons of System Events that always show up in the "Configuration History" part of the LSC. You can look at the calendar and tell exactly which days I used the computer because there will be System Events generated each day. Things like app crashes and failed drivers.
In July 2014, I got the first warning for the 16 GB SSD - the SMART Short Self-Test. By February this year it showed as failed for each hardware scan (these were initially set up to run monthly).
Also the whole time I've had it the touch screen would just stop working at some point and I would have to reboot to get it working again.
I finally called Lenovo on March 30th, before my warranty expired. When I called that time, I didn't realize the hard drive failure was the SSD. So they sent me a new 500 GB drive. I also added the other things into the case when I talked to them. For the wireless issue they suggested making sure the driver was up to date. I did this and let them know when I called back that it was up to date and still having the warning. So I called them to tell them to tell them about the wireless and also that I realized it was the SSD having the failure, not the main drive. The first case had already been closed even though none of the other items were addressed.
So they opened another case (this is #2). They said to mail them the laptop since the wireless issue would probably be on the board and it wasn't something I could fix myself. They sent a box with a prepaid overnight shipping label. I was very sick for a few days so I sent it back to them on April 10th (a Friday). Via UPS I saw it was delivered on Saturday. Work was performed on it Monday, April 13th and sent back to me that very day. I received it on April 14th. This part of the service has been excellent - very fast response.
Being in IT, I included a letter with the laptop that outlined the issues that should have been in the case. I also printed the hardware scans and what the system events looked like.
When I got the laptop back, the sheet inside said they had replaced the Speaker because of Distorted Sound. This was not even on the list even though I had noticed it. I didn't even power up the laptop before calling them again - yes, I was furious! Plus our power was out...
So this was noon on the 14th. They opened case #3 and sent me ANOTHER BOX so I could send it back.
After our power came back on the 15th, I powered up my laptop. I opened the browser (I have it set to restore the previous session) and there was a sexually explicit video on YouTube. I opened the other browser and there was a different video on YouTube. So this person was watching YouTube instead of fixing my laptop. I looked through both browser histories and there was quite a bit of activity while my laptop was at the repair center... I ran the hardware scan - still failed and a warning for the wireless. They really hadn't done anything.
I also found two pictures of the repair person in the recycle bin...
So I called back. I was LIVID! They opened another case (this is #4). And sent me ANOTHER BOX. I finally learned the other day that once a case is opened, it cannot be edited or added to at all. Instead, they close the other case and open a new one. I guess their turnaround time for closing cases is excellent! I've never seen a system like that - and I've used a lot of them.
I got a really nice, patient fellow on the line. He took all my info (again). I emailed him the pictures, screen captures of the YouTube videos, the letter I had sent - everything. He entered as much into the new case as he could - he talked to one of the supervisors to make sure he did it right. Somehow he flagged it so that the laptop would get more attention (time) at the repair facility. He also opened a separate case (an escalation ticket?) for a supervisor to call me regarding the person's conduct at the repair facility. He said they would call me that day. (It's now the 25th and I've never heard from anyone)
So, he sent me ANOTHER BOX. I've built up quite a stack of them.
Our power was out AGAIN from the 17th through the 19th (don't get me started).
I noticed a hardware scan had now gotten a failure on the main hard drive. So I called them on the 21st to add this to the case before sending the laptop back. The girl said they can't add anything to an existing case or edit it at all once it's opened. She would have to open a new case and SEND ME ANOTHER BOX. I told her to forget it because I was ready to send it in and didn't want to wait for another box. I also asked for a status on that "escalation case" where the supervisor was supposed to call me. In order to do this she, yes, wait for it, had to open ANOTHER CASE!! So they would know I wanted a status. I'm completely dumbfounded.
So I sent it back on the 21st. This time I practically wiped it. I had already removed all my files the last time, but I had left my bookmarks and browser history intact. I set up a guest logon with admin privileges. I updated my letter and printed off more stuff to include with the box. On one sheet I had only the case number, the serial number and machine type. On another sheet I had "DO NOT SEPARATE THIS PAPERWORK FROM THE LAPTOP" and the case number. I put this sheet on top (The guy on the 15th said my letter and stuff may have gotten separated from the laptop once it was delivered to the repair facility). I used a ton of staples so it would all stay together. I included in my letter the failure on the main hard drive and asked if they could look at it. I wrote about having to open a new case if I wanted to include it.
They received it on the 22nd. A nice gentleman from the repair facility called me that day asking about the password. that. was. written. on the sheet they have you fill out. I told him what happened last time and also mentioned the hard drive failure and asked if he could look into it. He said they would.
I received my laptop back yesterday morning.The sheet that came with it said they had "replaced the following parts to complete the repair of your laptop."
Part Description Symptom
IMAGE Replaced due to engineering change
System board Network card error
Hard disk drive Network card error
ECA-WIRELESS <no symptom listed>
There was also a sheet saying they had installed a factory preload of software and I needed to install Lenovo and Windows updates.
When I booted it up, the first thing I noticed, in the lower right corner was:
Windows 8.1
SecureBoot isn’t configured correctly
Build 9600
I ran a hardware scan. Well, I tried. It stopped part way through and said it finished successfully but most of the tasks showed up as cancelled. I tried to run it again - issues - rebooting ensued. It said the LSC wasn’t available and that I should try again or reboot.
Tried several times. Then got what I guess is the new BSOD - kinder, gentler:
Your PC ran into a problem and needs to restart. We're just
collecting some error info, and then we'll restart for you. (xx% complete)
If you'd like to know more, you can search online later for this error: DRIVER_CORRUPTED_EXPOOL
Even though the LSC said my Lenovo files were all up to date, I ran the Update. And first I had to download a new version of Update. Then I downloaded all of the Lenovo updates and installed them (there were quite a few). The BIOS update failed. While I was doing the Lenovo downloads, I got a light blue screen but no text (I was out of the room so I'm not sure what happened). Did CTRL-ALT-DEL and it shows only IE and Task Manager as applications that are running. Could not “Switch to” IE. Hitting window key to go to start didn't do anything. So I had to restart.
By 3pm yesterday there were 34 system events in the configuration history.
I ran the hardware scan again after I updated the Lenovo files, and you guessed it! Failure on the SSD (SMART Short Self-Test) and warning on the wireless. Nothing had changed. Except hardware scan is acting different than it did before I sent in the laptop for repairs. When it finishes, it instantly closes and just shows 100% complete. When I click on "see last results" it shows a screen called
Log Information,
Canceled 04/24/2015 n:nn pm
You have not done a hardware test on your computer
And the calendar in LSC only shows the very first hardware scan I did on Friday. Even the hardware scan screen shows the date and time of the last scan. It also shows the error code. In order to see exactly what is failing, I have to sit there and watch it very closely and snap a picture of the screen as soon as the error (or warning) shows up.
When I would try to run Windows update, it would hang up PC Settings. I couldn't even kill it using task manager because it didn't show up as a task. During this, I got a flag saying the firewall wasn't turned on. I tried to turn it on, but clicking on Turn on Windows Firewall didn't do anything. I tried to setup my Microsoft account but that just hung too.
I ended up running Windows Update FOUR TIMES to get all the updates installed. Every time I ran it, it said "Done!" and I would run it again and more would show up. The last time was this morning.
At some point, the error about SecureBoot went away.
Then, I created a bootable BIOS update disk. Following the ReadMe instructions, I went through ThinkPad Setup and verified several values. Of note:
Secure Boot was DISABLED. According to the ReadMe file, this should be ENABLED in Windows 8.1. I enabled it.
Under Startup/Boot, according to the ReadMe that came with the BIOS update, UEFI/Legacy Boot is supposed to be set at UEFI Only for Windows 8.1. Mine was set to "Both". I changed it.
In Startup, OS Optimized Defaults was DISABLED, even though it says right there (and in the BIOS update ReadMe) it should be ENABLED to meet Microsoft Windows 8 Certification Requirement.
After these updates, I flashed the new BIOS.
Then, I ran hardware scan again...
Now I have TWO failures on the SSD: Random Seek Test and SMART Short Self-Test. Great.
In the Event Viewer (that I recently discovered), it says my disk has a bad block. It just says The device, \Device\Harddisk\DR1, has a bad block. I assume this is the SSD...
There are 867 events in the event viewer - Critical, Error, and Warning...
Fifty-two of these are from October 7, 2013 - before my little laptop was a glimmer.
The rest are from when Lenovo had it and yesterday and today.
64 of them are the disk error.
341 are from DeviceSetupManager. 65 of those are from failed driver installs. 69 are for not being able to establish a connection to the windows update service. 64 are from not being able to establish a connection to the Windows Metadata and Internet Services (WMIS).
3 times it's rebooted without cleanly shutting down
60 of them are from Service Control Manager and say The TDKLIB service failed to start due to the following error: The system cannot find the file specified.
One of them says {Registry Hive Recovered} Registry hive (file): '\??\C:\Users\Default\NTUSER.DAT' was corrupted and it has been recovered. Some data might have been lost.
16 are warnings that various processors in Group 0 are being limited by system firmware.
12 say the certificate for local system with thumbprint <bunch of hex numbers> is about to expire or already expired.
108 are warnings for failure to load the driver \Driver\WUDFRd for various devices
16 are application errors
One is for the computer rebooting from a "bug check"
15 are for name resolutions timing out after none of the configured DNS servers responded.
10 are for SecureBoot being disabled.
14 for services terminating unexpectedly
15 are for WLAN Extensibility Module has stopped
61 are for applications not being able to be restarted because the application SID does not match Conductor SID
12 are for activation of CLSID timing out waiting for the service wuauserv to stop
So, I'll call them on Monday and open. a. new. case (#5?) - but really 7. And get A NEW BOX.
I'll keep you updated!Hi amycdero and welcome to the HP Forum,
I understand that you are having scanning and printing issues after upgrading to Mavericks OS X v10.9.1. I will try my best to help you resolve this issue.
In this document for Mac OS X: Scanning Software Does Not Open or Stops Responding are steps the may help you with your scanning issue.
This document for Fixing Ink Streaks, Faded Prints, and Other Common Print Quality Problems should help with the streaking printing issue.
I hope this information is helpful. Please let me know.
Thank you,
I worked on behalf of HP. -
"The certificate chain was issued by an authority that is not trusted" when migrating to SQL 2012
Environment:
1 Primary Site (USSCCM-Site.domain.com)
1 CAS (USSCCM-CAS.domain.com)
SQL 2008 R2 (USSCCM-CAS.domain.com)
SQL 2012 SP1 CU6 (USSQL12.domain.com)
Issue:
We were successfully able to migrate the CAS to the new SQL 2012 server, almost without incident. When attempting to migrate the Site instance however, we are getting errors. Screenshot below.
Attached is a copy of the log. But below is a highlight of what I think are the errors… It appears that either SQL or SCCM doesn’t like a certificate somewhere, but it is contradicting because the logs say that it has successfully tested connection to SQL.
I am lost.
Logs stating it can connect successfully to SQL
Machine certificate has been created successfully on server USSQL12.domain.com. Configuration Manager Setup 10/21/2013 10:20:10
AM 2100 (0x0834)
Deinstalled service SMS_SERVER_BOOTSTRAP_USSCCM-Site.domain.com_SMS_SQL_SERVER on USSQL12.domain.com. Configuration Manager Setup 10/21/2013 10:20:10 AM
2100 (0x0834)
SQL Server instance [sccmsite] is already running under the certificate with thumbprint[f671be844bf39dec7e7fdd725dc30e225991f28a]. Configuration Manager Setup 10/21/2013 10:20:10 AM
2100 (0x0834)
INFO: Testing SQL Server [USSQL12.domain.com] connection ... Configuration Manager Setup 10/21/2013 10:20:10 AM
2100 (0x0834)
INFO: SQL Connection succeeded. Connection: USSQL12.domain.com SCCMSITE\MASTER, Type: Unsecure Configuration Manager Setup 10/21/2013 10:20:10 AM
2100 (0x0834)
INFO: Tested SQL Server [USSQL12.domain.com] connection successfully. Any preceding SQL connection errors may be safely ignored. Configuration Manager Setup 10/21/2013
10:20:10 AM 2100 (0x0834)
INFO: Certificate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
Configuration Manager Setup 10/21/2013 10:20:10 AM 2100 (0x0834)
INFO: Created SQL Server machine certificate for Server [USSQL12.domain.com] successfully. Configuration Manager Setup 10/21/2013 10:20:10 AM 2100 (0x0834)
INFO: Configuration Manager Setup - Application Shutdown Configuration Manager Setup 10/21/2013 10:20:10 AM 2100 (0x0834)
INFO: Running SQL Server test query. Configuration Manager Setup 10/21/2013 10:20:10 AM 2100 (0x0834)
INFO: SQL Connection succeeded. Connection: USSQL12.domain.com SCCMSITE\MASTER, Type: Secure Configuration Manager Setup 10/21/2013 10:20:10 AM
2100 (0x0834)
INFO: SQL Server Test query succeeded. Configuration Manager Setup 10/21/2013 10:20:10 AM
2100 (0x0834)
INFO: SQLInstance Name: sccmsite Configuration Manager Setup 10/21/2013 10:20:10 AM 2100 (0x0834)
INFO: SQL Server version detected is 11.0, 11.0.3381.0 (SP1). Configuration Manager Setup 10/21/2013 10:20:10 AM 2100 (0x0834)
Logs saying certificate is not trusted
ERROR: SQL Server error: [08001][-2146893019][Microsoft][SQL Server Native Client 11.0]SSL Provider: The certificate chain was issued by an authority that is not trusted. Configuration Manager Setup
10/21/2013 10:20:49 AM 2100 (0x0834)
*** [08001][-2146893019][Microsoft][SQL Server Native Client 11.0]Client unable to establish connection Configuration Manager Setup 10/21/2013 10:20:49
AM 2100 (0x0834)
ERROR: SQL Server error: [08001][-2146893019][Microsoft][SQL Server Native Client 11.0]Client unable to establish connection Configuration Manager Setup 10/21/2013 10:20:49 AM
2100 (0x0834)
*** Failed to connect to the SQL Server, connection type: CCAR_DB_ACCESS. Configuration Manager Setup 10/21/2013 10:20:49 AM
2100 (0x0834)
INFO: SQL Connection failed. Connection: CCAR_DB_ACCESS, Type: Secure Configuration Manager Setup 10/21/2013 10:20:49
AM 2100 (0x0834)
*** [08001][-2146893019][Microsoft][SQL Server Native Client 11.0]SSL Provider: The certificate chain was issued by an authority that is not trusted. Configuration Manager Setup 10/21/2013 10:20:52 AM
2100 (0x0834)
ERROR: SQL Server error: [08001][-2146893019][Microsoft][SQL Server Native Client 11.0]SSL Provider: The certificate chain was issued by an authority that is not trusted. Configuration Manager Setup
10/21/2013 10:20:52 AM 2100 (0x0834)
*** [08001][-2146893019][Microsoft][SQL Server Native Client 11.0]Client unable to establish connection Configuration Manager Setup 10/21/2013 10:20:52
AM 2100 (0x0834)
ERROR: SQL Server error: [08001][-2146893019][Microsoft][SQL Server Native Client 11.0]Client unable to establish connection Configuration Manager Setup 10/21/2013 10:20:52 AM
2100 (0x0834)
*** Failed to connect to the SQL Server, connection type: CCAR_DB_ACCESS. Configuration Manager Setup 10/21/2013 10:20:52 AM
2100 (0x0834)
INFO: SQL Connection failed. Connection: CCAR_DB_ACCESS, Type: Secure Configuration Manager Setup 10/21/2013 10:20:52
AM 2100 (0x0834)
*** [08001][-2146893019][Microsoft][SQL Server Native Client 11.0]SSL Provider: The certificate chain was issued by an authority that is not trusted. Configuration Manager Setup 10/21/2013 10:20:55 AM
2100 (0x0834)
ERROR: SQL Server error: [08001][-2146893019][Microsoft][SQL Server Native Client 11.0]SSL Provider: The certificate chain was issued by an authority that is not trusted. Configuration Manager Setup
10/21/2013 10:20:55 AM 2100 (0x0834)
*** [08001][-2146893019][Microsoft][SQL Server Native Client 11.0]Client unable to establish connection Configuration Manager Setup 10/21/2013 10:20:55
AM 2100 (0x0834)
ERROR: SQL Server error: [08001][-2146893019][Microsoft][SQL Server Native Client 11.0]Client unable to establish connection Configuration Manager Setup 10/21/2013 10:20:55 AM
2100 (0x0834)
*** Failed to connect to the SQL Server, connection type: CCAR_DB_ACCESS. Configuration Manager Setup 10/21/2013 10:20:55 AM
2100 (0x0834)
INFO: SQL Connection failed. Connection: CCAR_DB_ACCESS, Type: Secure Configuration Manager Setup 10/21/2013 10:20:55
AM 2100 (0x0834)
*** [08001][-2146893019][Microsoft][SQL Server Native Client 11.0]SSL Provider: The certificate chain was issued by an authority that is not trusted. Configuration Manager Setup 10/21/2013 10:20:58 AM
2100 (0x0834)
ERROR: SQL Server error: [08001][-2146893019][Microsoft][SQL Server Native Client 11.0]SSL Provider: The certificate chain was issued by an authority that is not trusted. Configuration Manager Setup
10/21/2013 10:20:58 AM 2100 (0x0834)
*** [08001][-2146893019][Microsoft][SQL Server Native Client 11.0]Client unable to establish connection Configuration Manager Setup 10/21/2013 10:20:58
AM 2100 (0x0834)
ERROR: SQL Server error: [08001][-2146893019][Microsoft][SQL Server Native Client 11.0]Client unable to establish connection Configuration Manager Setup 10/21/2013 10:20:58 AM
2100 (0x0834)
*** Failed to connect to the SQL Server, connection type: CCAR_DB_ACCESS. Configuration Manager Setup 10/21/2013 10:20:58 AM
2100 (0x0834)
INFO: SQL Connection failed. Connection: CCAR_DB_ACCESS, Type: Secure Configuration Manager Setup 10/21/2013 10:20:58
AM 2100 (0x0834)
*** [08001][-2146893019][Microsoft][SQL Server Native Client 11.0]SSL Provider: The certificate chain was issued by an authority that is not trusted. Configuration Manager Setup 10/21/2013 10:21:01 AM
2100 (0x0834)
More logs saying cert is not trusted
*** [08001][-2146893019][Microsoft][SQL Server Native Client 11.0]SSL Provider: The certificate chain was issued by an authority that is not trusted. Configuration Manager Setup 10/21/2013 10:21:20 AM
2100 (0x0834)
ERROR: SQL Server error: [08001][-2146893019][Microsoft][SQL Server Native Client 11.0]SSL Provider: The certificate chain was issued by an authority that is not trusted. Configuration Manager Setup
10/21/2013 10:21:20 AM 2100 (0x0834)
*** [08001][-2146893019][Microsoft][SQL Server Native Client 11.0]Client unable to establish connection Configuration Manager Setup 10/21/2013 10:21:20
AM 2100 (0x0834)
ERROR: SQL Server error: [08001][-2146893019][Microsoft][SQL Server Native Client 11.0]Client unable to establish connection Configuration Manager Setup 10/21/2013 10:21:20 AM
2100 (0x0834)
*** Failed to connect to the SQL Server, connection type: CCAR_DB_ACCESS. Configuration Manager Setup 10/21/2013 10:21:20 AM
2100 (0x0834)
INFO: Updated the site control information on the SQL Server USSQL12.domain.com. Configuration Manager Setup 10/21/2013 10:21:39 AM
2100 (0x0834)
*** [08001][-2146893019][Microsoft][SQL Server Native Client 11.0]SSL Provider: The certificate chain was issued by an authority that is not trusted. Configuration Manager Setup 10/21/2013 10:21:39 AM
2100 (0x0834)
ERROR: SQL Server error: [08001][-2146893019][Microsoft][SQL Server Native Client 11.0]SSL Provider: The certificate chain was issued by an authority that is not trusted. Configuration Manager Setup
10/21/2013 10:21:39 AM 2100 (0x0834)
*** [08001][-2146893019][Microsoft][SQL Server Native Client 11.0]Client unable to establish connection Configuration Manager Setup 10/21/2013 10:21:39
AM 2100 (0x0834)
ERROR: SQL Server error: [08001][-2146893019][Microsoft][SQL Server Native Client 11.0]Client unable to establish connection Configuration Manager Setup 10/21/2013 10:21:39 AM
2100 (0x0834)
*** Failed to connect to the SQL Server, connection type: CCAR_DB_ACCESS. Configuration Manager Setup 10/21/2013 10:21:39 AM
2100 (0x0834)
CSiteSettings::WriteActualSCFToDatabase: Failed to get SQL connection Configuration Manager Setup
10/21/2013 10:21:39 AM 2100 (0x0834)
CSiteSettings::WriteActualSCFToDatabaseForNewSite: WriteActualSCFToDatabase(USA) returns 0x87D20002 Configuration Manager Setup 10/21/2013 10:21:39
AM 2100 (0x0834)
ERROR: Failed to insert the recovery site control image to the parent database. Configuration Manager Setup 10/21/2013 10:21:39 AM
2100 (0x0834)
Troubleshooting:
I have read on a few articles of other people having this issue that states to find the certificate on SQL 2012 that’s being used and export it to the SCCM server – which I’ve done.
http://damianflynn.com/2012/08/22/sccm-2012-and-sql-certificates/
http://trevorsullivan.net/2013/05/16/configmgr-2012-sp1-remote-sql-connectivity-problem/
http://scug.be/sccm/2012/09/19/configmgr-2012-rtm-sp1-and-remote-management-points-not-healthy-when-running-configmgr-db-on-a-sql-cluster/
-BradHi,
How about importing certificate in the personal folder under SQL server computer account into SCCM server computer account or SCCM server service account? That certificate is for SQL Server Identification. And you could
set the value of the ForceEncryption option to NO. (SQL Server Configuration Manager->SQL Server Network Configuration->
Protocols for <server instance>->Properties)
Best Regards,
Joyce Li
We
are trying to better understand customer views on social support experience, so your participation in this
interview project would be greatly appreciated if you have time.
Thanks for helping make community forums a great place. -
ISE EAP-Chaining with machine, certificate and domain credentials
Good morning,
A customer wants to do the following for their corporate wireless users (all clients will be customer assets):
Corp. wireless to authenticate with 2-factor authentication:
•1. Certificate
•2. Machine auth thru AD
•3. Domain creds
When client authenticates, they want to match on 2 out of the 3 conditions before allowing access.
Clients are Windows laptops and corporate iPhones.
Certs can be issued thru GPO and MDM for iPhones
Client supplicant on laptops is native Windows - which I understand is a compatibility issue from this thread: https://supportforums.cisco.com/thread/2185627
My first question is: can this be done?
Second question: how would i implement this from an AuthC/AuthZ perspective?
Thanks in advance,
AndrewYou can do this configuring anyconnect with NAM modules on endpoints! But I don't make sense configure some clients with certificate and others with domains credentials...
For your information, I'm actually configuring EAP-Chaining on ISE 1.2 and i'm gotting some problems. The first one I got with windows 8, for some reason windows was sending wrong information about the machine password but I solved the problem installing a KB on windows 8 machines (http://support.microsoft.com/kb/2743127/en-us). The second one I got with windows 7 that are sending information correctly about domain but wrong information about user credentials, on ISE logs I can see that windows 7 are sending user "anonymous" + machine name on the first longin... after windows 7 start if I remove the cable and connect again the authentication and authorization happen correctly. I still invastigate the root cause and if there is a KB to solve the problem as I did with windows 8.
Good luck and keep in touch.
http://support.microsoft.com/kb/2743127/en-us -
RDS and Gateway issues: Cannot get remoteapps to run without opening port 3389 on firewall
I am testing the setup of a small RDweb server to host QuickBooks for some remote sales users (4 users). For the most part, I have everything installed on one virtual server (using 2012r2 "Quick Start" session host deployment with the additional
Licensing and Gateway server roles added to the same server).
Everything works excellent with one exception. External clients cannot launch published apps without having port 3389 open on the firewall, even with the gateway role installed and the 'Deployment Properties' set to use the gateway. They can properly connect
to the RDweb site and view the published apps. The only way it works is open the firewall port (at which time I can disable the gateway or leave it configured and it works either way). Internally, everything works accordingly. I have followed the steps outlined
on many sites and have combed though the forum here to no avail.
Error received (summarized but is a well documented error):
remote desktop can't connect to the remote computer: 1- Your user account is not listed (it actually is) or 2- You might have specified the remote computer in NetBios format . . etc.
This is an existing SBS 2011 environment with additional virtual servers setup to host QuickBooks as outlined below:
Current setup:
Used Quick Start to install Remote Desktop Services in hosted sessions mode
Installed the additional roles for Licensing and Gateway server on same server
Configured wild card public certificates on all four services (Connection Broker(2), Web Access and Gateway)
Configured internal DNS to properly lookup our external FQDN of this server (ex. quickbooks.contoso.com points to quickbooks.contoso.local
One thing I noticed (just now) when I launch a published app and the firewall has port 3389 closed, a dialog box pops up directly after launching the app that warns about running a RemoteApp program and mentions the Remote Computer and the Gateway Server
as both the same (which it is); however, I would have assumed one would have listed the internal server's name while, instead, both are listed as the external FQDN. Either way, internal DNS should still allow it to properly route . . no? I don't know . . I'm
sure I am just missing something in a routing configurations somewhere. The gateway service is not properly looking up the RDweb service and then seeming not routing the encapsulated RDP session through HTTPS. . .. is my guess . .
I was reading about the "set published name" commandlet; however, I am not experiencing a certificate name mismatch; however, the certificate name does show up as *.contoso.com versus the actual name. I may just be grasping as straws now . . :)Ok, while I was in the server and looking over the BPA scans: "The Remote Desktop Gateway (RD Gateway) server Secure Sockets Layer (SSL) certificate may not have a valid certificate subject name." This may be due to it showing up as *.companyname.com
versus quickbooks.companyname.com. Anyhow. .. on to the list of actions above:
Changed RD RAP from "Select Active Directory" group to "Allow any network resource" and tested with port 3389 closed on firewall:
Worked. Initially it did not as I had used a custom shortcut created from earlier; however, after logging into the RDweb site again, the application loaded fine now (after the RD RAP change)
No error message appeared; however, I did notice that for a split second, the word Error did appear in the browser's tab title, but only very shortly. The app launch does take a bit longer too now (about 10-15 seconds, up from about 4 seconds with the port
open). This, I could care less about so long as we are properly forwarding the traffic through the gateway.
As for log entries, I had spend quite a bit of time in there and only had minor issues with loading user profile setting taking too long and policy settings preventing the redirection of USB devices. Looking again, no issues still. Just a bunch of informational
entries where I would connect before (and disconnect) but only with the port on the firewall open; otherwise, there was not an entry corrolating to when I would receive an error before. Now though, I am connecting after the RD RAP change and logs are showing
connections even with the port closed. These are in "operational", the "admin" log only shows the update to the RD RAP configuration.
Yes, the LAN's DNS server does relay the lookup information for my public FQDN as the local LAN address. No need for a local host record.
I have now added a new rule in our firewall to allow and forward UDP port 3391 traffic to the internal server hosting remote services
Thank you very much for your assistance on this matter. The RD RAP rule was default built during the creation of this services. Why is the resource not cross-referencing AD security groups? I could have sworn I created a group for that . . . -
Hi again!
I've installed mpd and sonata but i don't see my library in sonata .
This is my /etc/mpd.conf file
# An example configuration file for MPD
# See the mpd.conf man page for a more detailed description of each parameter.
# Files and directories #######################################################
# This setting controls the top directory which MPD will search to discover the
# available audio files and add them to the daemon's online database. This
# setting defaults to the XDG directory, otherwise the music directory will be
# be disabled and audio files will only be accepted over ipc socket (using
# file:// protocol) or streaming files over an accepted protocol.
music_directory "/home/andreas/Downloads"
# This setting sets the MPD internal playlist directory. The purpose of this
# directory is storage for playlists created by MPD. The server will use
# playlist files not created by the server but only if they are in the MPD
# format. This setting defaults to playlist saving being disabled.
#playlist_directory "~/.mpd/playlists"
# This setting sets the location of the MPD database. This file is used to
# load the database at server start up and store the database while the
# server is not up. This setting defaults to disabled which will allow
# MPD to accept files over ipc socket (using file:// protocol) or streaming
# files over an accepted protocol.
db_file "/var/lib/mpd/mpd.db"
# These settings are the locations for the daemon log files for the daemon.
# These logs are great for troubleshooting, depending on your log_level
# settings.
# The special value "syslog" makes MPD use the local syslog daemon. This
# setting defaults to logging to syslog, otherwise logging is disabled.
log_file "/var/log/mpd/mpd.log"
# This setting sets the location of the file which stores the process ID
# for use of mpd --kill and some init scripts. This setting is disabled by
# default and the pid file will not be stored.
pid_file "/var/run/mpd/mpd.pid"
# This setting sets the location of the file which contains information about
# most variables to get MPD back into the same general shape it was in before
# it was brought down. This setting is disabled by default and the server
# state will be reset on server start up.
state_file "/var/lib/mpd/mpdstate"
# General music daemon options ################################################
# This setting specifies the user that MPD will run as. MPD should never run as
# root and you may use this setting to make MPD change its user ID after
# initialization. This setting is disabled by default and MPD is run as the
# current user.
user "mpd"
# This setting sets the address for the daemon to listen on. Careful attention
# should be paid if this is assigned to anything other then the default, any.
# This setting can deny access to control of the daemon.
# For network
#bind_to_address "any"
# And for Unix Socket
#bind_to_address "~/.mpd/socket"
# This setting is the TCP port that is desired for the daemon to get assigned
# to.
#port "6600"
# This setting controls the type of information which is logged. Available
# setting arguments are "default", "secure" or "verbose". The "verbose" setting
# argument is recommended for troubleshooting, though can quickly stretch
# available resources on limited hardware storage.
#log_level "default"
# If you have a problem with your MP3s ending abruptly it is recommended that
# you set this argument to "no" to attempt to fix the problem. If this solves
# the problem, it is highly recommended to fix the MP3 files with vbrfix
# (available from <http://www.willwap.co.uk/Programs/vbrfix.php>), at which
# point gapless MP3 playback can be enabled.
#gapless_mp3_playback "yes"
# This setting enables MPD to create playlists in a format usable by other
# music players.
#save_absolute_paths_in_playlists "no"
# This setting defines a list of tag types that will be extracted during the
# audio file discovery process. Optionally, 'comment' can be added to this
# list.
#metadata_to_use "artist,album,title,track,name,genre,date,composer,performer,disc"
# Symbolic link behavior ######################################################
# If this setting is set to "yes", MPD will discover audio files by following
# symbolic links outside of the configured music_directory.
#follow_outside_symlinks "yes"
# If this setting is set to "yes", MPD will discover audio files by following
# symbolic links inside of the configured music_directory.
#follow_inside_symlinks "yes"
# Zeroconf / Avahi Service Discovery ##########################################
# If this setting is set to "yes", service information will be published with
# Zeroconf / Avahi.
#zeroconf_enabled "yes"
# The argument to this setting will be the Zeroconf / Avahi unique name for
# this MPD server on the network.
#zeroconf_name "Music Player"
# Permissions #################################################################
# If this setting is set, MPD will require password authorization. The password
# can setting can be specified multiple times for different password profiles.
#password "password@read,add,control,admin"
# This setting specifies the permissions a user has who has not yet logged in.
#default_permissions "read,add,control,admin"
# Input #######################################################################
input {
plugin "curl"
# proxy "proxy.isp.com:8080"
# proxy_user "user"
# proxy_password "password"
# Audio Output ################################################################
# MPD supports various audio output types, as well as playing through multiple
# audio outputs at the same time, through multiple audio_output settings
# blocks. Setting this block is optional, though the server will only attempt
# autodetection for one sound card.
# See <http://mpd.wikia.com/wiki/Configuration#Audio_Outputs> for examples of
# other audio outputs.
# An example of an ALSA output:
#audio_output {
# type "alsa"
# name "My ALSA Device"
## device "hw:0,0" # optional
## format "44100:16:2" # optional
## mixer_device "default" # optional
## mixer_control "PCM" # optional
## mixer_index "0" # optional
# An example of an OSS output:
#audio_output {
# type "oss"
# name "My OSS Device"
## device "/dev/dsp" # optional
## format "44100:16:2" # optional
## mixer_device "/dev/mixer" # optional
## mixer_control "PCM" # optional
# An example of a shout output (for streaming to Icecast):
#audio_output {
# type "shout"
# encoding "ogg" # optional
# name "My Shout Stream"
# host "localhost"
# port "8000"
# mount "/mpd.ogg"
# password "hackme"
# quality "5.0"
# bitrate "128"
# format "44100:16:1"
## protocol "icecast2" # optional
## user "source" # optional
## description "My Stream Description" # optional
## genre "jazz" # optional
## public "no" # optional
## timeout "2" # optional
# An example of a httpd output (built-in HTTP streaming server):
#audio_output {
# type "httpd"
# name "My HTTP Stream"
# encoder "vorbis" # optional, vorbis or lame
# port "8000"
## quality "5.0" # do not define if bitrate is defined
# bitrate "128" # do not define if quality is defined
# format "44100:16:1"
# An example of a pulseaudio output (streaming to a remote pulseaudio server)
#audio_output {
# type "pulse"
# name "My Pulse Output"
## server "remote_server" # optional
## sink "remote_server_sink" # optional
## Example "pipe" output:
#audio_output {
# type "pipe"
# name "my pipe"
# command "aplay -f cd 2>/dev/null"
## Or if you're want to use AudioCompress
# command "AudioCompress -m | aplay -f cd 2>/dev/null"
## Or to send raw PCM stream through PCM:
# command "nc example.org 8765"
# format "44100:16:2"
## An example of a null output (for no audio output):
#audio_output {
# type "null"
# name "My Null Output"
# This setting will change all decoded audio to be converted to the specified
# format before being passed to the audio outputs. By default, this setting is
# disabled.
#audio_output_format "44100:16:2"
# If MPD has been compiled with libsamplerate support, this setting specifies
# the sample rate converter to use. Possible values can be found in the
# mpd.conf man page or the libsamplerate documentation. By default, this is
# setting is disabled.
#samplerate_converter "Fastest Sinc Interpolator"
# Volume control mixer ########################################################
# These are the global volume control settings. By default, this setting will
# be detected to the available audio output device, with preference going to
# hardware mixing. Hardware and software mixers for individual audio_output
# sections cannot yet be mixed.
# An example for controlling an ALSA, OSS or Pulseaudio mixer; If this
# setting is used other sound applications will be affected by the volume
# being controlled by MPD.
#mixer_type "hardware"
# An example for controlling all mixers through software. This will control
# all controls, even if the mixer is not supported by the device and will not
# affect any other sound producing applications.
#mixer_type "software"
# This example will not allow MPD to touch the mixer at all and will disable
# all volume controls.
#mixer_type "disabled"
# Normalization automatic volume adjustments ##################################
# This setting specifies the type of ReplayGain to use. This setting can have
# the argument "album" or "track". See <http://www.replaygain.org> for more
# details. This setting is disabled by default.
#replaygain "album"
# This setting sets the pre-amp used for files that have ReplayGain tags. By
# default this setting is disabled.
#replaygain_preamp "0"
# This setting enables on-the-fly normalization volume adjustment. This will
# result in the volume of all playing audio to be adjusted so the output has
# equal "loudness". This setting is disabled by default.
#volume_normalization "no"
# MPD Internal Buffering ######################################################
# This setting adjusts the size of internal decoded audio buffering. Changing
# this may have undesired effects. Don't change this if you don't know what you
# are doing.
#audio_buffer_size "2048"
# This setting controls the percentage of the buffer which is filled before
# beginning to play. Increasing this reduces the chance of audio file skipping,
# at the cost of increased time prior to audio playback.
#buffer_before_play "10%"
# Resource Limitations ########################################################
# These settings are various limitations to prevent MPD from using too many
# resources. Generally, these settings should be minimized to prevent security
# risks, depending on the operating resources.
#connection_timeout "60"
#max_connections "10"
#max_playlist_length "16384"
#max_command_list_size "2048"
#max_output_buffer_size "8192"
# Character Encoding ##########################################################
# If file or directory names do not display correctly for your locale then you
# may need to modify this setting. After modification of this setting mpd
# --create-db must be run to change the database.
#filesystem_charset "UTF-8"
# This setting controls the encoding that ID3v1 tags should be converted from.
#id3v1_encoding "ISO-8859-1"
I've add the mpd daemon in rc.conf and i've chosen my directory /home/andreas/Downloads in sonata .Also i put mpd:ALL to etc/hosts.allow
Sonata connects fine to the server but i can't see my libary .
What might be the issue ?
Thanks again
Last edited by shak (2010-06-10 11:27:13)If you continue to have issues with permissions, the solution i use is to simply run MPD as my normal user, storing all the necessary directories and files under ~/.mpd and just pointing it at the config file I stuck there:
$ mpd ~/.mpd/config
No more permissions issues! There's an explanation of this in the wiki.
Maybe you are looking for
-
Javascript and adobe flashplayer don't work. They work on internet explorer
Is this a problem caused by a recent firefox update. I did not have the problem with javascript until this week. I have always had a problem with flashplayer
-
Too much tapping to change tracks?
Now someone please correct me if im wrong. When you pick a song on the new nano, the album cover comes up? You have to then tap the screen again to bring up the next track icon, and tap that change the track? So if you wanted to move forward 1 track,
-
Iphone not recognized and freezing iTunes
I have been thru all trouble shooting steps, talked with an Apple expert and done a complete system restore. This all stared with a corrupt download of a TV show, and an update to the latest itunes. Any ideas would really, really be apreciated!
-
hi when i run my application am geting below error,i don't have any duplicate bean in C:\Users\Tshifhiwa\AppData\Roaming\JDeveloper\system11.1.1.6.38.61.92\o.j2ee\drs\CascadingSOC\META-INF i only have two file=application,weblogic-application,am i jd
-
Z10 to connecting to Safaricom (Kenya) network
I have a BlackBerry Z10 purchased from Dubai but on putting a Safaricom SIM card, it does not connect to the network even though under Settings it shows the SIM card has been detected. I tried an Airtel (Kenya) SIM card and it works fine. Any idea wh