Conflict between EMU 1212M PCI-e and Gigabyte 970A-D3 High Latency!!!

I recently built a new DAW around my EMU 1212m PCI-e card using a Gigabyte 970A-D3 , Phenom2-X6 T1055 Chip. The reason I built this new DAW was because all of a sudden my old DAW started having unusually high latency and uneven core distribution (core 1 was amped out) this started after I flashed the BIOS to my old board and I updated Sonar to X1c. I tried various setting with the old DAW but could no longer get the performance prior to these changes. My original plan was to change the motherboard and memory and put into DDR3 and keep the original chip but that made things worse. So I then decided to go to the 6 core it was cheap enough so what the heck, but the same thing now luck. I then tried to use a USB based audio interface for the test I just purchased a Behringer UCA202 and I found a much improved response. My final test was to try yet another board my choice for the board was the MSI 870S-G54 and I got much better results but not as near as good as I was getting originally.
Please note that with each of these test I was exchanging cards to different slots, trying various BIOS setting and all driver are current and updated and baI sically doing what ever it take to troubleshooting a DAW but I have seen absolulty no changes. All power saving setting on the BIOS was turned off (C-1 halt, AMD Cool & Quiet, TurboBoost, etc)With the change to the MSI board I was able to get about 30 tracks of VST's running at about 6ms however with the Gigabyte board I was getting at 50ms with he same project it was crapping out.
Reaper has far less power usage as is expected from Reaper yet it was halting and glitching. Comparing the Behringer to the EMU showed about 25% less CPU useage.
My questions are as follows:
Anybody out there had a problem with the C1 update?
Anybody having trouble using a Gigabyte board?
Anybody having problems with the EMU card over any other Audio Interface?
Each time I updated a component I did a clean install of Win7-64bit. I should also let you know that I am using the 32bit versions of Reaper in Sonar only because the project that I am finishing now started in 32bit.
Does anyone have any clues? Please help.....

JJ,
Have you tried [url=http://www.thesycon.de/deu/latency_check.shtml">http://www.thesycon.de/deu/latency_check.shtml[/url]
This app may give you a better idea of what is going on in your system.
Also what resources are being used ? Is the card sharing IRQ's
With multicore systems sometimes you may want to try assigning CPU affinity to just one Process like the emaudsv.exe
Casey

Similar Messages

  • Is there a conflict between Safari 4.0.3 and the latest version of FlashPlayer? Everytime I try to download, FP ends up in "Disabled Plugins" in my Library, and I can't move it out of there.

    Is there a conflict between Safari 4.0.4 and the latest version of FlashPlayer? I have tried repeatedly to download and install the latter. Instead of properly installing, FP ends up in my Disabled Plugins folder in my Library. Help!

    Safari 4.0.4 or 4.0.3 ??  your profile shows you are running v10.6.8.
    If you are running v10.6.8, click your Apple menu  / Software Update. The current version of Safari is 5.0.5.
    Then if necessary, reinstall Flash.

  • Conflict between Audigy 2 ZS Pro and four Wifi PCI Ca

    Hello,
    I apologize for my wrong English.
    I am an happy user of Audigy 2 ZS Pro.
    I tried to install a WiFi PCI Card and the PC freeze just after the launch of Windows XP SP2.
    I tried with four cards with respect of installation procedures :
    - D-Link DWL-G520
    - OvisLink Evo-W54PCI
    - SMC-Networks SMCWPCI-GM
    - Netgear WPN3
    and none of them works.
    There is a conflict with memory resources allocation : D7DF8000-D7DFFFFF for Wifi Card and the same for Firewire port of Audigy.
    It is impossible (for me) to desactivate Firewire port on Audigy or changing memory allocation.

    I'm quite sure it's an incompatibility between the SLi and the audigy 2 card whether that's a driver conflict or hardware conflict I have yet to determine, since it's behavior is very random if I play games with sound disabled it works fine if I leave internet explorer open though when the page refresh click sound is played while I have a game running it will cause the comp to freeze and reboot. I did not have the realtec(k) ? drivers installed before I removed the audigy 2 card I also had the realtec onboard sound disabled in the BIOS as for speed settings I have no clue what you are talking about I pretty much leave teh bios settings default except for the disabling of the unused onboard devices.Message Edited by psaux on 03-28-20060:2 AM

  • Incompatibilities between Gigabit Ethernet PCI cards and Power Mac G5?

    Hi,
    we recently bought a Digicom PCI LAN GIGA32 Ethernet card to upgrade our Power Mac G5 1.8GHz server. The OS on the G5 is Mac OS X Server 10.4.8 (8L127).
    The issue is simple: the PCI card is recognized by the system (it appears in System Profiler and as a new port in System Preference's Network pane) but Mac OS X cannot properly use it. We tried to connect the card to a Gigabit switch but nothing happened: no led denoting the connection speed turned on on the switch and the Network Status view in the System Preference's Network pane still show the red light with the "No cable connected" message.
    We noticed this message in system.log:
    jedi kernel[0]: AppleRTL8169Ethernet: phyWaitForAutoNegotiation TIMEOUT
    So we tried to manually set the Ethernet speed for the card and indeed it reacted, but we managed to have it working only at 10 Mbps (10baseTX).
    It seems that AppleRTL8169Ethernet.kext [1] is used by Mac OS X to control Ethernet cards featuring the Realtek 8169 chipset but it cannot properly communicate with Digicom's card.
    The weird thing is that we tried the same card on a Power Mac G4 and it worked flawlessy. Maybe the issue depens on the PCI-X slots available on the Power Mac G5?
    Are there any other report of incompatibilites between Ethernet PCI cards with Realtek chipsets and Power Mac G5?
    BTW, we noted that the card's vendor doesn't certify the card for Macintosh systems but we didn't manage to find a PCI Gigabit Ethernet card certified to work with Mac OS X and Power Mac G5 hardware. Could you point me to some PCI Gigabit Ethernet cards proven to work with a Power Mac G5 machine?
    [1] file://localhost/System/Library/Extensions/IONetworkingFamily.kext/Contents/Plug Ins/AppleRTL8169Ethernet.kext/

    Is there something wrong with the built-in interface
    or do you want to trunk/bond interfaces or route
    between interfaces?
    Just experimenting…
    The interface that Apple had in G4 Xserves (Broadcomm
    chipset) 64 bit PCI would perhaps be a good buy if
    you can find it (available as spare part?).
    http://www.xlr8yourmac.com/OSX/osx_networkcards.html
    Thanks a lot for the link and the Broadcomm chipset hint.
    Meanwhile, I found that the Realtek website features a driver download for Mac OS X 10.4 and Ethernet cards with the 8169S-32 chipset (the one featured by the Digicom card tested).
    I think I'll give it a try and let you know how it goes.

  • Why do I get a class conflict between the Prepare SQL.vi and the Get Column Name.vi with the SQL Toolkit compatibility vis from the Database Connectivity Toolkit?

    I have done extensive programming with the SQL Toolkit with LabVIEW versions through 6.1. My customer now wants to upgrade to Windows 7, so I am trying to upgrade to LabVIEW 2009 (my latest purchased version) using the Database Connectivity Toolkit, and the SQL Toolkit Compatibility vis. Everything seemed to be going okay with the higher level SQL operations, but I ran into trouble with the Get Column Name.vi. 
    The pictures below show the problem. The original SQL Toolkit connected the Prepare SQL.vi with the Get Column Name.vi with a cluster of two references, one for connection, and one for sql. The new compatibility vis have a class conflict in the wire because the Prepare SQL.vi contains a cluster with connection, and command references, but the Get Column Name.vi expects a cluster with connection and recordset references. 
    How do I resolve this conflict?
    Thank You.
    Dan

    I've never worked with the old version of the toolkit, so I don't know how it did things, but looking inside the SQL prep VI, it only generates a command, and the the column name VI wants a recordset. I'm not super familiar with all the internals of ADO, but my understanding is that is standard - you only have the columns after you execute the command and get the recordset back. What you can apparently do here is insert the Execute Prepared SQL VI in the middle and that will return what you need.
    I'm not sure why it worked before. Maybe the execute was hidden inside the prep VI or maybe you can get the column names out of the command object before execution. In general, I would recommend considering switching to the newer VIs.
    Try to take over the world!

  • Is there a conflict between Firefox 3.6.13 and Adobe Reader X?

    Since installing Adobe Reader X I am frequently unable to open a pdf file from a remote site within the browser.

    I have Acrobat 8.1.6 and Reader XI on Win XP. Do these conflict? Should I get rid of the newer Reader?
    I'm having problems printing to the PDF print driver, locks up system, shows printer offline in spooler. I doubt problem is with driver itself because I can print a Test Page from it ok. But printing to Adobe PDF from Word & other apps locks up & never completes.
    There's an Exclamation Point next to Acrotray in Explorer. (see image)  What does this mean??
    Have tried Repair install of Acrobat twice.

  • Conflict between teststand models in NI and User folder

    Sir,
    I have customized NI's teststandmodel (modelsupport.cws) for my application and placed it in User folder. But still my application is using TestStandModel (modelsupport.dll) under NI folder.
    If I change t"StationModelPath2" in "TestExec.ini" under "National Instruments\TestStand 3.5\Cfg\"; am able to get the customized version of modelsupport.dll. In that case I am getting an error (Error1)during execution of the sequence as attached below. Another issue with this is if I try to open a teststand sequence through testStand another error (-17329) is poping up.
    Please help me out. I am using teststand 3.5 and labwindows 8.5

    Safari 4.0.4 or 4.0.3 ??  your profile shows you are running v10.6.8.
    If you are running v10.6.8, click your Apple menu  / Software Update. The current version of Safari is 5.0.5.
    Then if necessary, reinstall Flash.

  • Conflict between Photoshop 7.0.1 and Mac OS 10.6?

    I have just installed OS 10.6 on my Intel iMac.  I get the following message when I try to launch Photoshop 7.0.1: "An unexpected and unrecoverable problem has occurred because of a program error.  Photoshop will now exit", which it does.  I had no problems using PS with OS 10.4.  Help?

    A forum search yielded this for example:
    http://forums.adobe.com/message/1528779#1528779
    So You could either stay with Mac OS 10.4 or buy the new Photoshop.

  • Conflict between ATI Multimedia Center Library and iTunes

    I have the HDTV Wonder with my computer. I can record TV shows and in the ATI Multimedia Center Library, it's a "cinema" type of file. Whwn I listen live a TV show, the program record automaticaly the TV show and in the ATI Multimedia Center Library, it's a "TV-ON-DEMAND" type of file. Both of the two types of file have ".VCR" extention. I have no problem to listen the "Cinema" type of file. When I try to listen the "TV-ON-DEMAND" type, it's iTunes who start and it can't read this ".VCR" file. I can't find what is the problem. I have this problem since I upgrade iTunes. iTunes is not my default player and the .VCR file is associate to ATI Multimedia.

    Thanks a lot for no response  I discovered Disk Utility.

  • Possible Conflict Between iPhoto/OSX10.4.2 and POSER6

    Running iPhoto 5.0.4
    Upgraded to OSX 10.4.2 and POSER 6 over the weekend. Since this load I have lost access (from within iPhoto) to my photofiles. Thumbs load however cannot get full view (just the roatating circle) Then hangs until I click the Done Button.
    The Files are there and will open in Preview and Photoshop. Also cannot Import new files either by drag and drop or from Camera. Get error message stating that files might me in wrong format. Photofiles are OK and will Import to older mac running iPhoto 2 and OSX 10.2
    Have restored iPhoto from DVD and still the same.
    Any Ideas?

    Hi John,
    don't know if it is just a coincidence that your iPhoto problems started at the same time as you new installations or not.
    check out the suggestions on Page 1 to see if any help.
    iPhoto Help
    iPhoto Help 2

  • Is there a known conflict between a CalDigit FASTA-GU3 sata/USB 3 card and an ATI Radeon X1900XT video card?

    Hello all.
    I am having trouble with my Mac Pro (circa 2008) not powering up the monitor (an Apple HD Cinema Display 23 inch).
    Here's some history.
    For about two weeks I was having trouble waking up the monitor from sleep. I would have to reboot the computer to see the screen.
    Then the screen wouldn't wake up after many reboots. I tried the Apple Cinema Display on my MacBook Pro laptop an on an older Mac Mini. The display didn’t' work on any of them.
    I then hooked up a Samsung monitor to all three computers in turn. The Samsung worked fine with each.
    From that I deduced that it was Apple HD Cinema Display that was at fault.
    I replaced it with one I bought from a friend - in perfect working condition.
    The new Apple Display worked fine with my Mac Pro.
    Problem solved - or so I thought.
    Now, a few days later, I am having a repeat of the same problem. The Apple Cinema Display won't wake up.
    I removed all the peripheral devices, still no joy.
    I removed and reseated the video card (after blasting all with compressed air).
    Still no joy.
    I then removed the CalDigit FASTA-GU3 sata/USB 3 card I installed about a year ago.
    Now the Apple Display came back to life.
    So my question is, are there know conflicts between a CalDigit FASTA-GU3 and an ATI Radeon X1900XT video card?
    If so - is there a fix?
    Also open to other theories.
    Other tech specs:
    Mac Pro (from around 2008) 2 x 3 GHZ Quad Intel Xeon.
    OSX Lion
    The video card is an ATI Radeon X1900XT (512 MB)
    Apple HD Cinema Display - 23 inch
    Many thanks.

    Thanks for the info on the Expansion Slot Utility. I found it and ran it. It shows no problems. It shows the ATI Radeon X1900XT to be properly installed and running at full capacity.
    I found a reliable dealer of flashed ATI Radeon 5770 cards. A couple of trusted friends have had good luck with cards from the dealer.
    So I will have that on stand-by for when/if the existing card fails completely.
    Thanks everyone for your input.
    A

  • Conflict between audigy and Olympus voice recor

    I have an audigy se recently installed. Seemed to be working fine until I opened my Olympus voice recorder program. Just opening the program knocked out the sound card and I could not get it back again. No speakers in any application on the computer except the diagnostic test. Then the speakers would play. But no cd's, no wav files, no nothing. Tried checking and unchecking all the boxes. There really aren't that many. Only way to solve the problem was to uninstall and reinstall audigy and not go to Olympus anymore. I've done that several times to confirm that is the problem.
    Any suggestions?
    (5. sourround)

    Bazbear wrote:
    Could anyone help me to resolve the conflict between my Soundblaster Audigy 2ZS and Norton antivirus. The auto protect feature is constantly being turned off on boot up. According to Symantec the problem is caused by conflict between the two soft wares. The Creative page does not mention this at all and the work around on the Symantec site either does not work or entails time wasting closing of programs and re-boots. It is really getting to me now and I wonder if any one knows of a permanent fix?
    Bazbear
    Some past post here mention of this too.....and the mods suggestion does indeed helped some of them resolve it. Perhaps you can try it. What you need to do is uninstall all Norton and Creative software. When you're done with that, install Creative software first follow by Norton stuff.

  • I have a conflict between Firefox Version 5 and both Ebay and Fasthost Sitebuilder image uploads.

    Since upgrading to version 5 of Firefox subscreens of ebay are not displaying, Fasthost Sitebuilder has stopped allowing the import of pictures and I am being logged out of secure sites before transactions are completed.

    I encounter immediate problems on installing Firefox 5. There were 3 Windows 7 crashes and I could not access Firefox. It was determined that there was a conflict between the anti virus program and the 5 version. There is no download for the older version 4 was not available. After trying several fixes, nothing worked.
    One post indicated that Mozilla was not fixing Firefox 5 and that the fixes were made in Firefox 6 version. Reluctantly, I upgraded to six and , to my amazement, it works again. Nothing ventured, nothing gained!! Hope it works for you.

  • Having a conflict between Firefox 4 and Endnote

    After installing Firefox 4, when I tried to open Endnote (and yes I closed the program before installing Firefox 4) I got a message that Endnote was unable to open my library, check to see if anyone else is using it; if the problem persists use the recover library in Endnote. Well, I tried the recover library and it did not work. I did get my library back by moving the library to my desktop, I think all by references are there, however, I lost all my Groups, and the file attachments are all messed up.

    I encounter immediate problems on installing Firefox 5. There were 3 Windows 7 crashes and I could not access Firefox. It was determined that there was a conflict between the anti virus program and the 5 version. There is no download for the older version 4 was not available. After trying several fixes, nothing worked.
    One post indicated that Mozilla was not fixing Firefox 5 and that the fixes were made in Firefox 6 version. Reluctantly, I upgraded to six and , to my amazement, it works again. Nothing ventured, nothing gained!! Hope it works for you.

  • Conflict between Client object model and Item Updated Event Receiver in sharepoint 2010

    Hello All,
    As per my requirement I have a two custom list.
    Agent Details
    Port Name
    Agent Details contains Agent code, Port Name,  email, address and phone of Agent. Its possible that one Agent Code is connected with multiple Port Name.
    Basically what I am doing is I am getting port name connected with Agent code, using jquery and bind those values with check box(using javascript created dynamically) and bind all with Div tag.
    Now when my custom edit form of Agent list open up it shows me different port name binding with checkbox group.
    when user select the check box and click confirm button my clicent object model script will run and add this selected value into Port Name list. 
    After confirm one more button named Save will enable asking user to edit the email, phone or address value and when I click on save my Item updated event fires which update the values of the selected port name(These port name I am getting from port
    name list) to Agent Details custom list.
    Now when I am trying to update the values my event receiver fires or some times it got stuck(not firing). So could you please help me the possible alternative for this requirements.
    Can we user the Ecma Script(Client object model to preserve the value of selectec port) and Item updated event receiver on the same time?
    Is anything am doing wrong then please guide me.

    Hi,
    As I understand, when you updated values in the agent details list the Item updated event receiver got stuck sometimes.
    The item update event receiver will fire after the item has been saved, and the client object model script or the Ecma Script runs before the item is saved, so there is no conflict between the client object model script and item update event receiver.
    You could find out the reason about the item update event receiver gets stuck by debugging the event receiver.
    When you want to debug your event receivers, you have to attach to OWSTIMER.EXE and wait till they are executed. You can control this behavior using the Synchronization attribute. Also, if you’re looking for an easy way to debug an event receiver without
    having to manually attach a debugger to your code, you can use the System.Diagnostics.Debugger.Launch() method.
    The articles below are about how to debug in the event receiver in SharePoint 2010.
    http://sharepoint-kings.blogspot.jp/2013/02/debugging-event-receivers-in-sharepoint.html
    http://chakkaradeep.com/index.php/event-receivers-in-sharepoint-2010/
    http://sharesaint.com/?p=77
    Best regards,
    Sara Fan
    TechNet Community Support
    Please remember to mark the replies as answers if they help, and unmark the answers if they provide no help. If you have feedback for TechNet Support, contact
    [email protected]

Maybe you are looking for