Connecting the nexus 5500 with multiple vsans

Hi,
it's my first experience in the fibre channel world and i have a few doubts about the best way to connect the nexus 5500 to a EMC storage.
This is my scenario
this is my configuration:
vsan database
vsan 2
vsan 2 interface fc 1/1
vsan 3
vsan 3 interface fc 1/2
interface fc1/1
switchport mode f
no shut
interface fc1/2
switchport mode f
no shut
now I don't know how can I connect the port fc1/3 to the vnx storage, I think I can't make a trunk like ethernet, can anyone help me?
Or i only can do this with zoning
Thanks
Fred

Hello Fred,
All interfaces must be in the same vsan for them to see each other
vsan database
vsan 2 interface fc1/1, fc1/2, fc1/3
exit
Then you can zone each separately
example:
zone name host1 vsan 2
member pwwn 11:11:11:11:11:11:11:11    (host1 pwwn)
member pwwn 33:33:33:33:33:33:33:33    (VNX)
zone name host2 vsan 2
member pwwn 22:22:22:22:22:22:22:22    (host2 pwwn)
member pwwn 33:33:33:33:33:33:33:33    (VNX)
zoneset name Zoneset1 vsan 2
mem host1
mem host2
zoneset activate name Zoneset1 vsan 2
Thanks

Similar Messages

  • Connecting two Nexus 5020 with 10G ISL link

    Hi Experts,
    I am trying to connect two nexus 5020 with a 10G ISL link.
    Per my understanding, with new release 5.0.3 N2(2a) ISL link between two nexus switch is supported.
    Following is my config
    c5020-1(config)# show running-config int vfc 32
    !Command: show running-config interface vfc32
    !Time: Fri Dec  2 01:14:38 2011
    version 5.0(3)N2(2a)
    interface vfc32
      bind interface Ethernet1/32
      switchport mode E
      switchport trunk allowed vsan 3040
      no shutdown
    c5020-1(config)#
    c5020-1(config)# sho running-config int eth1/32
    !Command: show running-config interface Ethernet1/32
    !Time: Fri Dec  2 01:16:15 2011
    version 5.0(3)N2(2a)
    interface Ethernet1/32
      switchport mode trunk
      spanning-tree port type edge trunk
    c5020-1(config)#
    I have similar config on the other switch. But for some reason the link does not come up. vfc port keep "initializing" and Eth port stays isolated.
    c5020-1(config)# sh int vfc32
    vfc32 is trunking (Not all VSANs UP on the trunk)
        Bound interface is Ethernet1/32
        Hardware is Virtual Fibre Channel
        Port WWN is 20:1f:00:0d:ec:ca:04:bf
        Admin port mode is E, trunk mode is on
        snmp link state traps are enabled
        Port mode is TE
        Port vsan is 3040
        Trunk vsans (admin allowed and active) (3040)
        Trunk vsans (up)                       ()
        Trunk vsans (isolated)                 ()
        Trunk vsans (initializing)             (3040)
        1 minute input rate 0 bits/sec, 0 bytes/sec, 0 frames/sec
        1 minute output rate 0 bits/sec, 0 bytes/sec, 0 frames/sec
          0 frames input, 0 bytes
            0 discards, 0 errors
          0 frames output, 0 bytes
            0 discards, 0 errors
        last clearing of "show interface" counters never
        Interface last changed at Fri Dec  2 01:17:28 2011
    c5020-1(config)#
    c5020-1(config)# sh int eth1/32 fcoe
    Ethernet1/32 is FCoE Isolated
    c5020-1(config)#
    If any expert throw some light to make me understand things better will be helpful.

    i have not connected two Nexus before but looking at your eth 1/32 interfaces ..do you think it needs to be "
    switchport trunk allowed vlan" your "FCOE" VLAN ?

  • Connecting two Nexus switches with link

    Hi,
    I would like to connect two nexus switches with a link. Like one c5020 and one c5548p. How do i need to configure the ports at both the switches which will be joined with a fiber cable.
    For MDS switches such links becomes E-port and fabric is merged. Not sure what happenes at the Nexus swictches. Any input will be appreciated.
    Thanks,

    Do you have fc modules in each nexus? If so, they act much like the MDS 9148. All ports should be default auto speed and auto switchport mode. Insert fc-sfp's and a regular multimode fc cable between them. Default mode is fc switch.
    If that doesn't work, configure the mode on each port as E.
    Once done, the fc switch portion of each nexus will merge.
    Dave

  • How can I convert string to the record store with multiple records in it?

    Hi Everyone,
    How can I convert the string to the record store, with multiple records? I mean I have a string like as below:
    "SecA: [Y,Y,Y,N][good,good,bad,bad] SecB: [Y,Y,N][good,good,cant say] SecC: [Y,N][true,false]"
    now I want to create a record store with three records in it for each i.e. SecA, SecB, SecC. So that I can retrieve them easily using enumerateRecord.
    Please guide me and give me some links or suggestions to achieve the above thing.
    Best Regards

    Hi,
    I'd not use multiple records for this case. Managing more records needs more and redundant effort.
    Just use single record. Create ByteArrayOutputStream->DataOutputStream and put multiple strings via writeUTF() (plus any other data like number of records at the beginning...), then save the byte array to the record...
    It's easier, it's faster (runtime), it's better manageable...
    Rada

  • Pioneer 8400 DVD receiver player, as iPhone ios6 update now when connecting the new iPhone with ios6 via blutooth (firmware prob) to my car DVD 8400 unit, when playing music such as on my phone or Pandora the track button does not function or work at all

    pioneer 8400 DVD receiver player, as iPhone ios6 update now when connecting the new iPhone with ios6 to my car DVD 8400 unit, when playing music such as on my phone or Pandora the track button does not function or work at all not even if i press skip track forward or back on the unit it doesn't function everything works except that. on listening to radio or anything else related not pairing thru Bluetooth unit works fine, seems there to be Bluetooth update that is not making iPhone and unit not compatible at all. does pioneer need fix this problem with update firmware or thru apple need help. my iPhone was working fine before with previous ios 5 before.

    Dear Valued Pioneer Customer:
    We would like to inform you of the availability of an optional Bluetooth® firmware update (HW05-SW01.27.20) that enables Bluetooth AVRCP control and metadata display from a compatible Pioneer CD or DVD Receiver when used with an iPhone® 5 or iOS 6 device.  If you do not own an iPhone 5 or iOS 6 device, there is no need to install this update.
    This firmware update may be used only with the following 2012 Pioneer products:
    CD Receivers
    DVD Receivers
    DEH-P8400BH
    DEH-P9400BH
    DEH-80PRS
    AVH-P2400BT
    AVH-P3400BH
    AVH-P4400BH
    AVH-P8400BH
    In order to perform this update, the following items are needed:
    A Pioneer CD or DVD Receiver above with built-in Bluetooth
    Laptop with built-in Bluetooth running Windows® 7
    Bluetooth firmware update (HW05-SW01.27.20)
    How to Obtain the Free Firmware Update
    1. Download the INSTRUCTIONS for the optional Bluetooth firmware update (HW05_SW01.27.20).
    2. Download the UPDATE FILE to a computer and transfer the file to a compatible 2012 Pioneer CD or DVD Receiver via a Bluetooth-enabled Windows 7 laptop.
    You can also arrange for Pioneer to update your 2012 Pioneer CD or DVD Receiver by calling Pioneer Customer Service toll free at 800-421-1404 during regular business hours (M-F 10AM-7:30PM Eastern Time, except on holidays). If this firmware update is performed by Pioneer, there is a charge of $60.00 (this charge includes return shipping of the updated unit within the U.S.). Charges for removal/reinstallation of the unit and shipment to Pioneer are the customer’s responsibility.
    How to Determine if the Firware Update has Already been Installed
    CD Receivers:
    • With the unit turned off (press and hold the source button until the CD Receiver turns off), press and hold the center of the volume knob to bring up the Settings menu → rotate the volume knob until "BT Version Info" is displayed and then press the center of the volume knob → The firmware version should show HW05-SW01.27.20.
    DVD Receivers:
    • With the unit turned off (press the home button and select ‘OFF’ from the source icons), press the home button → Press the “System” icon at the bottom of the screen → Select the “Bluetooth Version Info” option → The firmware version should show HW05-SW01.27.20.
    If the Bluetooth firmware version shows HW05-SW01.27.20, no further action is necessary.
    Questions
    If you have any questions, please contact the Pioneer Customer Service Center toll free at 1-800-421-1404, Monday through Friday, 10:00 a.m. to 7:30 p.m. (Eastern Time), except on holidays.
    Sincerely,
    Pioneer Electronics (USA) Inc.

  • You must have connected the Time Capsule with a router that does not work with my direct cable from my ISP

    you must have connected the Time Capsule with a router that does not work with my direct cable from my ISP

    I tried to answer in your other post.. please stick to one thread ..
    What method of internet do you have.. is this fibre install.. if so the TC should just plug in and use dhcp in router mode.. press and hold the reset and it will go back to router mode by default.

  • Can I connect the iphone 3gs with ipad 2?

    Hallo
    can I connect the iphone 3gs with ipad 2?

    You can connect it to use the iPhone as a personal hotspot for the iPad, or to transfer photos/videos via the camera connection kit. You can't connect them in order to transfer music, documents etc.

  • LSMW program to upload the sales order with multiple line items.

    Dear SD and PP Gurus,
    I am new to creating LSMW Program.
    I want to create a LSMW program to upload the sales order with multiple line items. I have read on SDN that it can be done on two phases. First Create Header Data than line items. IS IT TRUE??, Or
    Is there any procedure by which we can load the sales orders with multiple line items in a single run (part).
    I want to use Batch process, not a BAPI or IDOC procedure.
    I have created a program with
    object 0090
    Method 0000
    Program Name RVINVB10
    Program Type D
    Source Structure 1 - For Header and Source Structure 2  for Line Items.
    Mapped Field INDET (With Fix Value 1), ORDERTYPE, SALESORG, DISTCHANNEL, DIVISION, CUSTOMER, PONUMBER , DELVDATE, PRCGDATE, PMTTERM
    INCOT1 INCOT2 with Source Structure - 1 and
    Field INDENT (With Fix Value 2),  ITEMNO, MATCODE, MATQTY, SUOM, PLANT, BATCH, AMOUNT with Structure-2
    than maintained Structure relation ship, field Mapping, Specified Files, Assigned files, Read Data and other process,
    At final stage (Start Direct Input program RVINVB10) it is giving a message - Table name not allowed.
    Please tell me where I am wrong.
    Thanks in advance.
    DSC

    Dear SD Gurus n Experts,
    I have solved the above problem. But there is another problem appearing regarding the date format. Now system generating a message: Date . . is not valid.
    While I am using Date: YYYYMMDD format in flat file, which is SAP's Standard Format.
    In SDN Link: LSMW upload Sales Order using VA01/VA02     I have found that there are some date fields which are mandatory to filled. Here I have mapped
    VDATU - Requested delivery date,  BSTDK - Customer purchase order date,  PRSDT - Date for pricing and exchange rate,  BSTDK_E - Ship-to party's PO date, FKDAT - Billing Date, KORDT - Delivery Date,
    and PRGRS - Date type is Constant = D
    Can any one tell me, where is the priblem.
    With thanks,
    DSC

  • I connected the TC T2 with the iMac and used Air Port Utility to have it join my existing network. Now I have green lights on Apple Base Station and TC with the cable connected to the Base Station because hen connected to TC -- I get only yellow lights fl

    I connected the TC T2 with the iMac and used Air Port Utility to have it join my existing network. Now I have green lights on Apple Base Station and TC with the cable connected to the Base Station because hen connected to TC -- I get only yellow lights flashing on both devices> 
    When Connected through the Apple Base station I have perfect internet wireless capability thru-out house.
    Lamont

    I connected the TC T2 with the iMac and used Air Port Utility to have it join my existing network. Now I have green lights on Apple Base Station and TC with the cable connected to the Base Station because hen connected to TC -- I get only yellow lights flashing on both devices> 
    When Connected through the Apple Base station I have perfect internet wireless capability thru-out house.
    Lamont

  • Do I need to connect the AirPort Extreme with a ethnet cable

    Do I need to connect the AirPort Extreme with a ethnet cable

    Hi Tracy,
    I have an airport express connected by ethernet cable to a Netgear modem which is connected to a phone socket. Those devices stay at one end of the house. I can use my MacBook Pro to connect to the internet (by Wi-Fi, no cables) anywhere else in the house.  I hope this helps.
    Ian.

  • Connect the music file with the artwork file post-computer-crash?

    I want to retrieve artwork after restoring my computer?
    So my computer (where itunes app data was stored) and my external hardrive (where my itunes library was stored) crashed, but luckily I had my itunes library was stored on dropbox so I have that uploading to my revived computer!
    I have access to all my "old computer's" files (via a mounted image file that looks just like an external drive H: )
    The "old computer" itunes used my dropbox folder for the library (J:work\Dropbox\Allen's Transfer Folder\iTunes)
    my "New comuter" uses a local folder but the contents are exactly the same (C:\Companies\Dropbox\Allen's Transfer Folder\iTunes)
    How can I get the artwork data from my "old computer" onto my "new computer" so that itunes will connect the music file with the artwork file?
    is there a data file and will they automatically sync to the artwork if they are in different locations?
    Thank you for your help, Allen

    pfanzier wrote:
    … is there any reason i shouldn't delete the artwork folder?
    All of my music is from CDs, so all of my cover art are scanned images that I added to the music files in iTunes. My Album Artwork folder is heavily populated nonetheless. Thus, it stands to reason that if you delete the folder, just like every other default item in your iTunes folder it will be recreated when you launch iTunes. If I recall correctly, that folder also holds the data files for building your CoverFlow.
    pfanzier wrote:
    itunes only demarcates songs whose files are missing with an exclamation point after i click on the song. otherwise everything appears as normal. if i quit itunes and reopen it, nothing is marked with the exclamation point until i click on it.
    I personally have never had an issue with missing song links, but based on what I had read on the Macworld forums over the years, when links are lost, people start seeing /!\ next to several tracks in their iTunes library. Of course, most of the instances that I have read about have been after iTunes updates so perhaps it is during the library updating after a software update that causes the automatic detection of broken links. Otherwise, it does make sense that iTunes would not check a link until the user selects an unlinked song, because iTunes does not, and should not, scan your entire library for no apparent reason.

  • Uplink-ID 0 in Nexus 5500 with FEX 2248.

    Hi all,
    I've got 2 Nexus 5548 and a fex 2248 connected to both of them via a vPC. 1 Uplink port goes to N5K-01 e1/10 and a second Uplink port goes to N5K-02 to port e1/10.
    On the log of the first Nexus 5500 I see this:
    N5K-01 %FEX-5-FEX_PORT_STATUS_NOTI: Uplink-ID 0 of Fex 103 that is connected with Ethernet1/10 changed its status from Configured to Fabric Up
    N5K-01 %FEX-5-FEX_PORT_STATUS_NOTI: Uplink-ID 1 of Fex 103 that is connected with Ethernet1/10 changed its status from Fabric Up to Connecting
    N5K-01 1 %FEX-5-FEX_PORT_STATUS_NOTI: Uplink-ID 1 of Fex 103 that is connected with Ethernet1/10 changed its status from Connecting to Active
    On the log of the second nexus 5500, I see this:
    N5K-02 %FEX-5-FEX_PORT_STATUS_NOTI: Uplink-ID 0 of Fex 103 that is connected with Ethernet1/10 changed its status from Configured to Fabric Up
    N5K-02 %FEX-5-FEX_PORT_STATUS_NOTI: Uplink-ID 2 of Fex 103 that is connected with Ethernet1/10 changed its status from Fabric Up to Connecting
    N5K-02 %FEX-5-FEX_PORT_STATUS_NOTI: Uplink-ID 2 of Fex 103 that is connected with Ethernet1/10 changed its status from Connecting to Active
    What is the difference between Uplink-ID 0, 1 and 2? If I only have 2 uplink ports, why is there a third one?
    Thanks in advace for your assistance.

    Hi Sonu,
    I see the similar problem on my nexus5ks. show cfs peer does not display the peer information. I have been waiting for hours now.
    sw01# sh cfs peerCFS Discovery is in Progress ..Please waitCould not get response. The network topology may be under going change.Please try after about 30 seconds
    Did you find the fix7workaround of this problem ?
    Regards,
    Umair

  • How can I share only the same music with multiple iTunes accounts

    Hello
    I hope someone can help. [I am using Windows Vista (Unfortunately J) and iTunes 10]
    I am trying to share the same music library with multiple iTunes accounts. Basically, I want to know if there is a way to automatically upload to other libraries when importing new music into my library, vice versa. [Better information below]
    Me, my sister and my dad all use iTunes (on different iTunes accounts), and before now we used to have are own music on our own windows user. Due to many duplicates and a loss of hard drive space I have brought an external hard drive and organised all the music.
    It was all going well - I first populated all the music onto my iTunes, exported the library, and then imported it on both the other users. However! Because this is only a copy of the library, when I try to import a new CD, it will not show up on there’s until I “Add File to Library”! Originally I thought about using the same library however we each have are own apps etc, that we don’t want to share.
    If you need anymore information please ask!
    Matt

    Hello roaminggnome
    Unfortunately the support is down at the moment, I will have a better look later. I did go though the Apple support previously, however I found nothing that worked.
    The first thread I came across was “Home Sharing” however no mater what I did, it did not appear in the iTunes sharing list (I did go though the “Show Sharing Networks” support as well)
    Secondly, I saw “Using A Single Library With Multiple Accounts On The Same PC” (Something like that) but all this did was let us share the same music location, if I was to rip extra music, it will not show in there library
    Matt

  • How to Connect the Apogee Duet with Digitech Vocalizer 3

    I have been trying to figure out how to interface my guitar and microphone with the Apogee Duet 2 using the Digitech Vocalizer 3 (voice correction). I would like someone from Apple to verify what I have found, but this is how I finally got it to work:
    1. Connect you microphone directly to the Vocalizer as shown in the instructions. If you are using a condenser mic, remember to activate the 48v power on the back of the Vocalizer.
    2. Set the Vocalizer output to mono (on back of device), and connect one cable from either output port of the Vocalizer to the Input 2 of the Apogee Duet.
    3. Use a 1/4" splitter (one mail 1/4" that splits into 2 female 1/4") to attach two standard 1/4" guitar amp cables to the output of your guitar. Connect one of these to the "Guitar In" port on the back panel of the Vocalizer.  Connect the other to Input 1 of the Apogee Duet.
    4.  Open the Apogee Maestro Software, and select "Input".  You should see both devices listed (1 and 2). The Apogee will not recognize the Vocalizer as a microphone, so set both of these devices to "Inst". 
    5.  Open Garage Band and add both instruments.
    6. When you add your guitar, remember to set your Input Source to "Mono 1" and turn the Monitor On so you can hear it through your hed phones. Also, make sure you have the headphone Icon selected on the Instrument panel.
    6.  When you add you Vocalizer (Instrument 2), select "Vocals" and "no effects". Remember to set your input source to "Mono 2" and turn your Monitor On so you can hear it through your hed phones. Also, make sure you have the headphone Icon selected on the Instrument panel.
    7. If you want to hear and record both instrumental tracks, go the "Track" menu and select "Enable Multi-Track Recordning."
    In summary, the Apogee Duet does not appear to recognize the Vocalizer as a microphone, so you have to set up the connection from the Vocalizer to the Duet as another instrument.

    #3 Can't you just plug your guitar into the Vocalizer's guitar in jack and then use the guitar thru jack to the apogee?

  • How to connect the IPad 2 with an HTC desire HD (mobilephone)

    Hello,
    I need your advice. I'm trying to connect my IPad 2 with may HTC desire HD via bluetooth. The tools are paring but do not conncet alt least. What can I do?

    What can I do?
    Nothing.  iOS does not support pairing to devices other than keyboards, headphones and headsets.

Maybe you are looking for