Connection is not following the Sticky database when one router is comming to up state.
Dear Team,
We have 2 routers configured in Cisco ACE.( Router 1: 10.250.226.4,Router 2: 10.250.226.6) and VIP 10.250.226.19. In a normal scenario all the client connections are perfectly handled by ACE and Its sending to client request to router as per the sticky database. When the router 10.250.226.4 is down, ACE cleared all the sticky database entry belongs to the 10.250.226.4. All the client connections are shifted to router 10.250.226.6.
when router 10.250.226.4 is comes, backup connections are not loadbalance properly. That is connection not following sticky database for second connections of the same ip and giving issue in establishing IPSEC connectivity. Please find the below output.
switch/RRI# sh sticky database client 10.239.10.86
sticky group : STIK-RRI-FRM
type : IP
timeout : 1440 timeout-activeconns : FALSE
sticky-entry rserver-instance time-to-expire flags
---------------------+--------------------------------+--------------+-------+
10.239.10.86 CISCO-7206-06:0 65274 -
switch/RRI# show conn | i 10.239.10.86
1517152 2 in UDP 90 10.239.10.86:4500 10.250.226.19:4500 --
1427552 2 out UDP 9 10.250.226.4:4500 10.239.10.86:1637 --
3051606 2 in UDP 90 10.239.10.86:500 10.250.226.19:500 --
3049659 2 out UDP 9 10.250.226.6:500 10.239.10.86:44977 --
Please find the below sample configuration we are done in ACE.
parameter-map type connection UDP_PARAM_MAP
set timeout inactivity 86450
sticky ip-netmask 255.255.255.255 address source STIK-RRI-FRM
replicate sticky
serverfarm RRI-FRM
class-map match-all RRI-VIP
2 match virtual-address 10.250.226.19 any
policy-map type loadbalance first-match RRI-VIP-l7slb
class class-default
sticky-serverfarm STIK-RRI-FRM
policy-map multi-match RRI
class RRI-VIP
loadbalance vip inservice
loadbalance policy RRI-VIP-l7slb
loadbalance vip icmp-reply
connection advanced-options UDP_PARAM_MAP
interface vlan 90
ip address 10.250.226.17 255.255.255.240
peer ip address 10.250.226.18 255.255.255.240
access-group input ALL
access-group output ALL
service-policy input REMOTE_MGMT
service-policy input RRI
no shutdown
As per the analysis its looks seems to be tthe bug CSCsv63364, CSCsu95356. Kindly suggest how we can resolve this issue.
Image version: A2(3.4)
Thanks in advance.
Regards,
Ranjith
Hi,
Its important to know whether there was a sticky entry when the router went down and the time it came back up. Leastconnection shouldn't be a problem here.
If the IPSEC connection is active but not the UDP 500 connections, after timeout the UDP 500 connections will be removed as well as the sticky entry. If the current active IPSEC connection suddently needs to refresh SA's a new UDP 500 connection will be open and it could be sent to a different server. There is no evidence that this is the problem but want to try a higher sticky timeout has a fix for this.
Siva
Similar Messages
-
Will not recognize the Lucid LG when connected with USB
My Dell will not recognize the Lucid LG when connected with USB. Both the computer and phone gives a split second prompt that they are connected but then goes away immediately. After reconnecting it several times however it will finally recognize the mass storage. How can I get away from the hassle of multiple re-connections before it finally recognizes that connection?
That's some helpful information about your issue samrmusso! Some recommendations that I have for you is to try a different USB port on the computer to see if it isn't an issue with that specific USB port. Are you using the cable that came with the device (recommended) or a 3rd party cable (may not support data transfering properly)? You can also try restarting both the device and computer and retest. It's possible that there's a driver conflict on your Dell. Here's how to check for these types of conflicts: http://goo.gl/qH4m5
Keep us posted on any additional information/details about your issue.
Thanks,
MikeS_VZW
Follow us on Twitter @VZWSupport -
My iPhone 4 has lost SIM connection several times over the past week when the phone is left on continually. I have had the SIM checked and it was not the source of the problem. I have found that I can reactivate the SIM by switching the phone off and on again. Has anyone else experienced this problem and if so, is there an easy fix. I have been advised by Apple that the latest IOS update may overcome this situation but I'm only on slow download speeds and 690 Mb would take forever. I would appreciate any advice.
Best regards,
Rob.PinguXeF wrote:
, while I have taken a backup of the iTunes Library,
this means nothing if it was not done correctly...
To have EVERYTHING on a New Computer...
From your OLD computer...
Copy your ENTIRE iTunes FOLDER to an External Drive... and then from the External Drive to your New Computer..
Full Details Here > http://support.apple.com/kb/HT1751 -
When I updated by iphone with IOS7, my calendar entries did not follow the icloud. I am only showing pre set calendar entries for the year and lost all other calendar entrie and it will not take any new entries. They show up in my outlook, but not on my iphone, which they did before I updated my software to the new i0s7
Before syncing, select each calendar on your Mac and back it up by going to File>Export>Export. If anything goes missing, you can use these to restore your calendars.
Have you tried simply force closing the calendar app on your iPhone? To do this, double-tap the home button, locate the calendar app, then swipe up on the image above the app icloud to close it and tap the home bottom. Then test your calendar again. -
Database schema SCM does not contain the associated database objects
I am getting the following error when i am trying to migrate the form to apex using application migration.
"*Database schema SCM does not contain the associated database objects for the project, aafs.*
*Ensure the database schema associated with the project contains the database objects associated with the uploaded Forms Module .XML file(s).* ".
Actully i am having one schema which i named as SCM, and i have defined one table TT.
I created one form test.fmb in which i used TT table.its compiled successfully.
Then i generated the xml file using frmf2xml from fmb file. After that, I created the project in appication migration wizard in SCM schema.
Project creattion is working fine.but when i m trying to create application,it is showing me above error.
can any one help in solving this problem.Hi Hilary,
Thanks for your response/feedback.
1. The schema associated with the project does not contain the necessary objects Can you please verify that the schema associated with your Forms conversion project does in fact contain the objects associated with the uploaded files. Could you also verify that the object names referenced in the error message do not exist within the schema associated with your workspace. Ensure that the schema associated with the project contains the necessary database objects before proceeding to the generation phase of the conversion process.
Ans:
Yes it does contain the objects (See results from SQL query Commands below):
SELECT MWRA_CONTRACT_NO, OLD_CONTRACT_NO FROM PROJECTS@CONTRACT_LX19.MWRA.NET
ORDER BY MWRA_CONTRACT_NO
000000569 551TA
000000570 553TA
000000575 560TA
000000576 561TA
000107888 502TA
000108498 500TA
000108502 503TA
2. The block being converted contains buttons, which may have been incorrectly identified as database columns, and included in the original or enhanced query associated with your block This is a known issue ,bug 9827853, and a fix will be available in our upcoming 4.0.1 patch release. Some possible solutions to this issue are:
-> delete the buttons before generating the XML
-> delete the button tags from the XML
-> add "DatabaseItem=No" for the button in the XML file before importing it in Apex.The button is excluded when creating the Application.
Ans
yes it does contain push buttons to transfer to another forms and these are defined as Non data base items. Parial XML code provided below:
- <Item Name="REPORTS" FontSize="900" DirtyInfo="true" Height="188" XPosition="4409" FontName="Fixedsys" ForegroundColor="black" DatabaseItem="false" Width="948" CompressionQuality="None" YPosition="3709" FontSpacing="Normal" Label="REPORTS" BackColor="canvas" FillPattern="transparent" ShowHorizontalScrollbar="false" FontWeight="Medium" ShowVerticalScrollbar="false" FontStyle="Plain" ItemType="Push Button">
<Trigger Name="WHEN-BUTTON-PRESSED" TriggerText="GO_BLOCK('REPORT_1');" />
</Item>
- <Item Name="TRACKHDR" FontSize="900" DirtyInfo="true" Height="188" XPosition="3409" FontName="Fixedsys" ForegroundColor="black" DatabaseItem="false" Width="948" CompressionQuality="None" YPosition="3709" FontSpacing="Normal" Label="TRACK" BackColor="canvas" FillPattern="transparent" ShowHorizontalScrollbar="false" FontWeight="Medium" ShowVerticalScrollbar="false" FontStyle="Plain" ItemType="Push Button">
<Trigger Name="WHEN-BUTTON-PRESSED" TriggerText="GO_BLOCK('TRACKHDRS');" />
</Item>
- <Item Name="SUBAWRD" FontSize="900" DirtyInfo="true" Height="188" XPosition="2429" FontName="Fixedsys" ForegroundColor="black" DatabaseItem="false" Width="948" CompressionQuality="None" YPosition="3719" FontSpacing="Normal" Label="SUBAWARDS" BackColor="canvas" FillPattern="transparent" ShowHorizontalScrollbar="false" FontWeight="Medium" ShowVerticalScrollbar="false" FontStyle="Plain" ItemType="Push Button">
3. If you are still experiencing issues, then please create a testcase on apex.oracle.com and update this thread with the workspace details so I can take a look.
Test case details are given below. It was created per ORACLE for open Service Request Number 3-1938902931 on ORACLE Metalink.
Workspace: contract4
username: [email protected] (my email)
Password: contract4
Comments:
For my migration/testing purpose a dabatase link and synonyms have been setup by our ORACLE DBA. Could this be causing this problem?
Do we know when the fix 4.0.1 patch release will be available?
Thanks for your help.
Indra -
Process does not follow the routing ends up in complete status
Installed Adobe LiveCycle server ES 2.5 with SQL Server 2008 as database
And followed the tutorial ‘Create Your First LiveCycle Application’
Deployed it on the server when I test the same
i.e. when the workspace user fills in form details and hits complete button it ends up as status complete
And not assigned to next user in the route
The process does not follow the routing it ends up in complete status
And nothing shows up when trying to record and play back the process
Tried invoking Via workbench too
no errors in the server log
Could this be an installation issue any pointers appreciated
Please adviseIssue with Jboss as it was taking longtime time to start due to low CPU ideally it should not take more than 3 to 5 minutes
Process works now -
My ipad is not showing the apn settings when i selected cellular data option on settings? y?
my ipad is not showing the apn settings when i selected cellular data option on settings? y?
pvonk, you were right, something was amiss. It is just a shared calendar (me and my PA) and nothing I could do would seemingly connect the iCal and cloud accounts.
Late last night I upgraded from OSX 10.7.4 to 10.7.5, as I thought that might resolve some settings or minor corruptions in the way my Mac Book was working.
This morning I opened iCal, and once again it attempted to refresh the page. And a few seconds later my iCloud diary appeared on iCal.
The moral of this issue is I think as follows.... when you check all the settings and follow all the advice, and something like this is still not working then it could be the software is slightly corrupt, so a re-install or applying an update (if there is one available) will help resolve issues.
So spot on advice, something was amiss and is now resolved thanks -
A new application built on a schema not in the portal database
I want to create a new application using the create "new application" function of the "build" tab of Portal.
I want this application to use a schema not in the Portal Database. The schema the application has to use belongs to a different database residing on the same machine the Portal database resides.
But the Portal "Application Name and Schema" form does allow me to choose a schema outside the Oracle Portal database.
I run Oracle Portal Version: 3.0.7.6.2 on WNT.
Thank for any suggestion.Maurizio
Carol's right. Create a schema in the local database then create a db link to the remote db connecting as that schema user (or some other of your choice). In my experience this has to be a public db link.
I run a portal application against a database on another sun box. There's some hassles, but it works ok mostly.
The db link connects as the user to the remote database and I grant privileges in the remote db to that db link user. I also have public synonyms in the portal database that point to the objects in the remote db. I have public synonyms in the remote database that sort out the schema of the objects required.
This sounds complicated and I've explained it in a rush, but if you sit down and work it through it's not so bad. You may find a better way, but after several trials I've got a setup that works.
Also, when I create a form I always refer only to the synonym - never to a schema.object. That way you can adjust the synonym easily without rewriting your report.
I always make reports from sql for the reason that you can change the sql, though I always refer to my synonym never to schema.object.
Session info doesn't travel well to the remote instance. I've had to build a work-around to get my table triggers in the remote instance to figure out who the portal user is because wwctx_api.get_user returns public.
I've been unable to directly call procedures in the remote database from portal components, but I've got around that by creating wrapper procedures in the local database.
It hasn't been a trivial exercise, but it does work.
Greg
I want to create a new application using the create "new application" function of the "build" tab of Portal.>I want this application to use a schema not in the Portal Database. The schema the application has to use belongs to a different database residing on the same machine the Portal database resides.>>But the Portal "Application Name and Schema" form does allow me to choose a schema outside the Oracle Portal database.>>I run Oracle Portal Version: 3.0.7.6.2 on WNT.>>Thank for any suggestion. -
All photos does not follow the stream
Seemingly only random pictures does not follow the photo stream from iphone to macbook - any clues how that can happen, or where I start the troubleshooting..?
..and a little bit more specific:
I noticed that some photos in the iPhone photo album doesn´t appear in the photo stream. I cannot find a continous error in this behaviour: this summer I noticed that every other picture was missing in the stream, but just from one weekend. Last weekend just ONE picture in the album was missing in the stream.
It´s really odd, wouldn´t you say?
I haven´t really made full follow-up during the autumn, since I hoped this phenomena would "disappear" along with the continous upgrading of iPhone, Macbook, iPhoto etc. So, it must be the Cloud that behaves strangely...?
The one picture from last weekend was imported to iPhoto when connecting iPhone and macbook "by cord" along with the videos,
The thing with the iCloud photo stream shod be that you wouldnt have to keep track of your photos by counting them or relying on cord connection, right?
Any ideas, anyone? -
I copied a workbook that has a working scheduled refresh
modified the data model, added some new reports
added a new source (PQ from azure market place)
uploaded workbook to new powerbi location.
get the following error when i try to turn on scheduled refresh - this is even if i just select one data source that is still identical to the original (working) workbook
Test connections settings validation failed: one or more connections did not pass the test
Technical Details ▼
Correlation ID: ddcab6b8-ff2c-4881-9d8e-eeabbd23dff2
Date and Time: 12/12/2014 06:13:06 AM (UTC)
what's the problem?
Jakub @ Adelaide, Australia BlogStill a problem and not just for me but other users going by the threads on here...
https://social.technet.microsoft.com/Forums/en-US/eb8682f4-9b40-456a-a7f1-45627a0f4ff0/cannot-schedule-refresh?forum=powerbiforoffice365#eb8682f4-9b40-456a-a7f1-45627a0f4ff0
Applies to all worksheets that utilise a PQ connection registered in the gateway. (my gateway is on an azure VM)
Existing worksheets receive this warning. New workbooks that utilise these connections also receive this warning
Adding a new PQ to the gateway and a new workbook that uses the new connection also receives this warning.
Every PQ connection I have receives this warning. My PQ connections are all to web resources. Most are to the workflowmax.com API, and one is to the Azure Marketplace to retrieve data for a date dimension.
Note: this does not prevent me from scheduling or triggering a refresh, and the refresh itself completes successfully. It's just a weird warning that caused confusion as it sounds like the actual refresh will fail as well seeing as the connection test failed.
Jakub @ Adelaide, Australia Blog -
Clearing Document Date do not follow the define clearing date in F-03.
Hi,
Clearing Document Date do not follow the define clearing date BKPF-BUDAT in F-03.
My user received the unpresented check statement from the bank on 31 Dec 2010. As 1 Jan 2011 is holiday and he came back to the office on 5 jan 2011. He post manual upload (Debit : Bank Outgoing and Credit : Unpresented Cheque) posting date 31.12.2010 (period 12/2010 and 01/2011 still open) . Hence the next step (same date on 5 Jan 2011) is to clear the Bank outgoing using F-03. He put 31.12.2010 as his Clearing date BKPF-BUDAT but when the system post the clearing date is 04/01/2011.
Please helpHello,
Hope it helps.
But i can recall for the EBS bank statement upload into a previous fiscal year, ie, 31.12.2010. I had to close the current fiscal year temporarily.
See what happens in your system when it tries to clear with F-03. Though as mentioned re-check as F-03 will default to the system date --- today.
Regards
Waza -
When using rabbitmq-jms for vFabric RabbitMQ javax.jms.Message.getJMSDestination does not return the actual destination when it is received from a consumer listening on a Topic with a wild card. I have tested with both 1.0.3 and 1.0.5 clients with RabbitMQ 3.1.5.
I was wondering if the community was aware of this problem and if there are any workarounds? If not what is the proper channel to file a bug report. An example code snippet is below. The test fails because the TextMessageMatcher expects the destination passed in on construction (second parameter) to equal the desination on the message received (aquired from getJMSDestination).
Mockery context = new Mockery();
final MessageListener messageListener = context.mock(MessageListener.class);
final Latch latch = new LatchImpl();
final String prefix = "test" + System.currentTimeMillis();
context.checking(new Expectations() {
oneOf(messageListener).onMessage(with(new TextMessageMatcher("MSG1", prefix + ".1234")));
will(new CustomAction("release latch") {
@Override
public Object invoke(Invocation invocation) throws Throwable {
latch.unlatch();
return null;
final Connection connection = createConnection(null, null);
Session session = connection.createSession(false, Session.AUTO_ACKNOWLEDGE);
connection.start();
Topic wildcardTopic = (Topic) getInitialContext().lookup(prefix + "." + "#");
Topic destination = (Topic) getInitialContext().lookup(prefix + ".1234");
final MessageConsumer consumer = session.createConsumer(wildcardTopic);
consumer.setMessageListener(messageListener);
MessageProducer producer = session.createProducer(null);
producer.send(destination, session.createTextMessage("MSG1"));
latch.await(5000);
connection.close();
Thread.sleep(5);
context.assertIsSatisfied();Check where your MDB sends the [response] messages to.
-
Glom – Could not create the new database
I would like to try Glom, but always get the this error
"Glom could not create the new database. Maybe you do not have the necessary access rights. Please contact your system administrator."
This happens with both local and extern server configuration. Any ideas on how to fix this?
Regards,
RenkeIt would also help, if you install the application and just tell me, if you get the same error, when trying to create a database. Maybe it's just a problem on my side.
Regards,
Renke -
"could not complete the requested operation" when i try to open the program
"could not complete the requested operation" when i try to open the program
what can i do
illustrator ccaccupub,
The following is a general list of things you may try when the issue is not in a specific file (you may have tried/done some of them already); 1) and 2) are the easy ones for temporary strangenesses, and 3) and 4) are specifically aimed at possibly corrupt preferences); 5) is a list in itself, and 6) is the last resort.
1) Close down Illy and open again;
2) Restart the computer (you may do that up to 3 times);
3) Close down Illy and press Ctrl+Alt+Shift/Cmd+Option+Shift during startup (easy but irreversible);
4) Move the folder (follow the link with that name) with Illy closed (more tedious but also more thorough and reversible);
5) Look through and try out the relevant among the Other options (follow the link with that name, Item 7) is a list of usual suspects among other applications that may disturb and confuse Illy, Item 15) applies to CC, CS6, and maybe CS5);
Even more seriously, you may:
6) Uninstall, run the Cleaner Tool (if you have CS3/CS4/CS5/CS6/CC), and reinstall.
http://www.adobe.com/support/contact/cscleanertool.html -
Photoshop CS4 is not tracking the mouse pointer when using various tools.
We have windows 7 Pro 32 bit using adobe CS4.
Core i5 and core i7 processor
4GB installed RAM
ATI 1GB 4570 Graphics card.
Also on various other hardware spec the same error.
The tool brush, pen or erase etc is not following the mouse pointer smoothly. There is a delay and if you attempt to draw quickly e.g a circle you instead get a jagged linepolygon shape. The writing is trailing the pointer by less than one second.
We have tried installing on a pc with no other software to test if there is a conflict and get the same error.
Can anyone advise what the resolution is.
ThanksTrevorBurroughs wrote:
Hi, I got a brand new 15" MacBook Pro a week or so back and had problems with the trackpad - when I tap to select an item the mouse pointer "bounces" off the item I'm trying to select. It happens randomly - not every time. Very irritating. Supplier got me a replacement machine, and it's doing the same thing! Is anyone else experiencing this issue? I migrated all my data and settings from my old Mac Pro (2011 model, also running Mavericks) via Time Machine - could that have an impact? Not using any non-Apple power supplies or other devices. Any input would be welcomed.
Migrating user from one machine to another should not be a cause of your symptoms.
Curious two machines in a row. Did this happen before you transferred data/ or di you check.
You have 14 days to return/exchange if you are not satisfied.
You could Try resetting NVRAM/PRAM http://support.apple.com/kb/ht1379 but I don't see it.
Did you try making adjustments to trackpad settings
>Sys Pref>Trackpad> Point & Click>speed
Maybe you are looking for
-
Windows Vista Home Premium SP2 Thunderbird 31.3.0 Norton advises me that there is malware in my inbox and that I should delete it. If I do so, how can I restore the inbox folder. I'm not worried about the contents, I just don't want to destroy my ema
-
Error when trying to create a Dynamic UI Element(DropDownByKey)
Dear All, I am trying to create a Dynamic UI element(dropdownbykey) . I used the following code which i wrote in domodify: if (firstTime) IWDTransparentContainer thetransparent =(IWDTransparentContainer)view.getElement("AttributeDynamic_TransparentCo
-
Can i use a external thunderbolt harddrive to copy my imac hard drive.
how fast would a thunderbolt external hard drive be, if i were to copy my Imac hard drive as a backup or image. At the moment its taking 4 hours to copy 95gig using my USB external hard drive......Seems like forever!!!!!
-
Can't import photos via drag-and-drop (only small thumbnail will appear)
After I drag and drop photos into iPhoto 7.1.3 (even a photo just exported from iPhoto), it shows the import process and creates an untitled event. Once complete, I see a dashed-line box instead of the images. http://idisk.mac.com/phildame/Public/Pic
-
I need to work offline but firefox wont let me
I use a virtual server to complete my web design work and recently downloaded firefox 3.6.13. Now when I try to use the browser offline all I get is a message telling me firefox is currently in offline mode and to uncheck the "work offline" in the fi