Conversion from Lightweight to Autonomous

Hey guys,
I'm trying to get an Access Point 1140 Series to go back to Autonomous, but when I type archive download-sw /overwrite /reload tftp://1.2.3.4/autonomous-image.tar It says it doesn't recognize that command.
It's connected to a WLC 2504 with software version 7.6
Thanks.

If the AP is still connected to the WLC, then enter the command in the WLC to convert the AP to autonomous: config ap tftp-downgrade <TFTP IP address> <IOS FILEMANE.TAR> <AP name>
If the AP is no longer connected to the WLC, then read this: Using a TFTP Server to Return to a Previous Release

Similar Messages

Convert a 2602i from lightweight to autonomous?

I have a CAP2602i that I would like to convert from lightweight to autonomous. Is this possible as with the older APs?
I'm following the instructions for the older models http://www.cisco.com/en/US/docs/wireless/access_point/conversion/lwapp/upgrade/guide/lwapnote.html#wp161272 with the adjustment of renaming file ap3g2-k9w7-tar.152-2.JB.tar to ap3g2-k9w7-tar.default.
Here is my console output at the point that I am failing:
process_config_recovery: set IP address and config to default 10.0.0.1
process_config_recovery: image recovery
image_recovery: Download default IOS tar image tftp://255.255.255.255/ap3g2-k9w7
-tar.default
examining image...
DPAA Set for Independent Mode
DPAA_INIT = 0x0
%Error opening tftp://255.255.255.255/ap3g2-k9w7-tar.default (connection timed o
ut)ap:
ap:
The IP address of my PC is set to 10.0.0.2. The max timeout I can set on my TFTP server is 20 seconds. Could this be my problem?
Thanks in advance! Any help would be apprectiated!

Hi Mantej,
It does not work with these new APs 1600/2600.
You need to perform these steps:
Restart the Access Point
While it loads the image in flash, press Escape, you’ll enter ROMMON mode:
The system boot has been aborted. The following
commands will finish loading the operating system
software:
ether_init
tftp_init
boot
Set the IP address for the gigabit 0 interface:
ap: set IP_ADDR 10.0.0.1
ap: set netmask 255.255.255.0
Initialize the tftp, ethernet and flash subsystems:
ap: tftp_init
tftp_init success: You can now use tftp file system!
ap: ether_init
Initializing ethernet port 0...
Ethernet speed is 100 Mb - FULL Duplex
ap: flash_init
Initializing Flash...
...The flash is already initialized.
Load the image from TFTP and extract it to flash:
ap: tar -xtract tftp://10.0.0.100/ap3g2-k9w7-tar.152-2.JB.tar flash
After it’s done, set the correct bootimage:
ap: set BOOT flash://ap3g2-k9w7-mx.152-2.JB/ap3g2-k9w7-xx.152-2.JB
Boot the system:
ap: boot

AIR-RM1252G-E-K9 changing from lightweight to autonomous?

Hi Everyone
I have a AIR-RM1252G-E-K9 access point which is in lightweight mode but need to change it to autonomous mode. After doing a bit of googling i understand its as simple as tftp'ing over an autonomous image. Ive found a link below which states that i need version 12.3 or earlier:
http://www.cisco.com/en/US/docs/wireless/access_point/conversion/lwapp/upgrade/guide/lwapnote.html#wp161272
However i can only find images for this access point starting from 12.4.
Can anyone just clear things up for me and perhaps point me in the right direction?
thanks

I downloaded the image c1250-k9w7-tar.124-21a.JA1.tar. I want to enable DHCP but i cant do this. Can anyone help me out with this?
Hmmmm ... It's either I don't understand what is your problem or something else. For starters, 12.4(21a)JA1 supports the AP being a simple DHCP server:
WAP(config)#ip dhcp pool ?
WORD Pool name
Next, you said you've "downloaded" the IOS. Can you post the output of "sh version" please?

Convertion from Lightweight to Autonomous access points

Is it possible to convert AIR-LAP1121G-E-K9 Lightweight access point to autonomous access point.

Hi tm,
You can convert AIR-LAP1121G-K-E9 to autonamus access point,pls do follow the procedur
Follow these steps to revert from LWAPP mode to autonomous mode by loading a Cisco IOS release using a TFTP server:
Step 1 The static IP address of the PC on which your TFTP server software runs should be between 10.0.0.2 and 10.0.0.30.
Step 2 Make sure that the PC contains the access point image file (such as c1200-k9w7-tar.122-15.JA.tar for a 1200 series access point) in the TFTP server folder and that the TFTP server is activated.
Step 3 Rename the access point image file in the TFTP server folder to c1200-k9w7-tar.default for a 1200 series access point, c1130-k9w7-tar.default for an 1130 series access point, and c1240-k9w7-tar.default for a 1240 series access point.
Step 4
Connect the PC to the access point using a Category 5 (CAT5) Ethernet cable.
Step 5
Disconnect power from the access point.
Step 6
Press and hold MODE while you reconnect power to the access point.
Step 7
Hold the MODE button until the status LED turns red (approximately 20 to 30 seconds) and then release.
Step 8
Wait until the access point reboots, as indicated by all LEDs turning green followed by the Status LED blinking green.
Step 9
After the access point reboots, reconfigure it using the GUI or the CLI.
Thankx&Regds
Saji k.s

1142 Lightweight to Autonomous

Hello all,
I am trying to convert an 1142 from lightweight to autonomous. I've found this post:
https://supportforums.cisco.com/thread/2055997
However the following command is not available via the CLI: archive download-sw /overwrite tftp://
Any thoughts?
Thank you,
Jeff

Hello
I am using Product/Model Number: AIR-LAP1242AG-N-K9 with following IOS information:
BOOT path-list:      flash:/c1240-rcvk9w8-mx/c1240-rcvk9w8-mx
Config file:         flash:/config.txt
Private Config file: flash:/private-config
Enable Break:        no
Manual Boot:         no
Enable IOS Break:    no
HELPER path-list:
NVRAM/Config file
      buffer size:   32768
      Mode Button:    on
Now I want to convert this to Autonomous mode but command
"debug capwap console cli
or
debug lwapp console cli"
are not working. Could you please confirm the command for converting LWAP to Autonomous AP for the mentioned IOS
Regards,
Manish Sharma

Steps to convert access point from LightWeight mode to Autonomous mode

I need steps to convert the following access point from Lightweight mode to Autonomous mode
AIR-AP1242AG-E-K9
Regards,
Majid

Hi Majid,
The method is just hidden a little further down the doc that Scott linked (+5 points Scott :)
Using a TFTP Server to Return to a Previous Release
Note This section does not apply to Cisco C3201WMIC and Cisco C3201LAP.
Follow these steps to revert from LWAPP mode to autonomous mode by loading a Cisco IOS release using a TFTP server:
Step 1 The static IP address of the PC on which your TFTP server software runs should be between 10.0.0.2 and 10.0.0.30.
Step 2 Make sure that the PC contains the access point image file (such as c1200-k9w7-tar.122-15.JA.tar for a 1200 series access point) in the TFTP server folder and that the TFTP server is activated.
Step 3 On the PC where the TFTP server is located, perform these steps:
a. Disable any software firewall products, such as Windows firewall, ZoneAlarm firewall, McAffee firewall, or others.
b. Ensure all Windows files are visible. From Windows Explorer, click Tools > Folder Options > View > Show hidden files and folders.
Step 4 Rename the access point image file in the TFTP server folder to c1200-k9w7-tar.default for a 1200 series access point, c1130-k9w7-tar.default for an 1130 series access point, c1240-k9w7-tar.default for a 1240 series access point, and c1250-k9w7-tar.default for a 1250 series access point.
Step 5 Connect the PC to the access point using a Category 5 (CAT5) Ethernet cable.
Step 6 Disconnect power from the access point.
Step 7 Press and hold MODE while you reconnect power to the access point.
Step 8 Hold the MODE button until the status LED turns red (approximately 20 to 30 seconds) and then release.
Step 9 Wait until the access point reboots, as indicated by all LEDs turning green followed by the Status LED blinking green.
Step 10 After the access point reboots, reconfigure it using the GUI or the CLI.
http://www.cisco.com/en/US/docs/wireless/access_point/conversion/lwapp/upgrade/guide/lwapnote.html#wp160918
Hope this helps!
Rob

Convert from LAP to autonomous mode issue

I bought some after market 1242's for extended coverage in my warehouse. The current 1242's I have are all set up in autonomous mode.
When I console into the AP's I bought they are looking for a CAPWAP -Controller obviously from the previous environment. There is nothing on the AP or in the sh version showing LAP.
*Mar 1 00:46:37.102: %CAPWAP-3-ERRORLOG: Did not get log server settings from DHCP.
*Mar 1 00:46:38.104: %CAPWAP-3-ERRORLOG: Could Not resolve CISCO-CAPWAP-CONTROLLER.xxx
*Mar 1 00:46:38.106: %CAPWAP-3-ERRORLOG: Could Not resolve CISCO-LWAPP-CONTROLLER.xxx
*Mar 1 00:48:38.106: %CAPWAP-5-DHCP_RENEW: Could not discover WLC using DHCP IP. Renewing DHCP IP.
#sh version
#Version 12.4(21a)JA2
System image file is "flash:/c1240-rcvk9w8-mx/c1240-rcvk9w8-mx
I cant seem to be able to reset these to where they aren't looking for the Controller. I can login with the default username and password Cisco/Cisco but I cant do an erase. I get the privileged command prompt but cant do erase star or a config t??? Is there something I'm missing here that I need to to?
So far these commands have worked::
debug capwap console cli
debug capwap client no-reload
So can I downgrade or go back to autonomous mode or do I have to reload an IOS again? I don't have a license so my options there are limited.
Any ideas??? Thanks

HI,
As pe your post:
System image file is "flash:/c1240-rcvk9w8-mx/c1240-rcvk9w8-mx
This is lightweight image. for this image you need controller.
If you want to use as autonomous AP. Then you must convert it to Autonomous mode.
Autonomous image code : k9w7
More about images:
http://rscciew.wordpress.com/2014/01/04/understand-access-point-ios-images/
Here is the procedure to convert to autonomous :
https://supportforums.cisco.com/document/57476/lwapp-autonomous-conversion-and-vice-versa-access-points
http://paulbeyer.wordpress.com/2010/01/16/converting-a-cisco-ap-from-lwapp-to-autonomous-mode/
http://www.youtube.com/watch?v=QQ_NuxdRhQ4
Regards
Dont forget to rate helpful posts

1252 Lightweight to Autonomous (Standalone AP)

Hi All,
Can someone help me to convert
1252 Lightweight to Autonomous (Standalone AP) as i don't have WLC I have tried some doc but no luck and below commands are did not worked even
debug lwapp console cli
debug lwapp client no-reload
archive download-sw /overwrite t
ftp://10.0.0.1/c1250-k9w7-tar.xxxxxsx
I can ping from CLI to my TFTPD32 and FROM PC to AP too
Thanks In Advance

Sheraz,
take a look at the document below. it walks you through the process.
http://www.cisco.com/en/US/partner/docs/wireless/access_point/conversion/lwapp/upgrade/guide/lwapnote.html#wp160918
HTH,
Steve
Please remember to rate helpful posts or to mark the question as answered so that it can be found later.

887VAW 802 lightweight to Autonomous

Hi guys, I've managed to 'upgrade' the onboard 802 AP to lightweight in error but cannot find a way to 'downgrade' it back to autonomous mode. I've read various threads but none of then work for me. Any advice would be welcome. Thanks Robbie.

You can convert an access point from lightweight mode back to autonomous mode by loading a Cisco IOS Release that supports autonomous mode (Cisco IOS release 12.3(7)JA or earlier). If the access point is associated to a controller, you can use the controller to load the Cisco IOS release. If the access point is not associated to a controller, you can load the Cisco IOS release using TFTP.
Note In some LWAPP deployments, the LWAPP controller resides between the access points and the rest of the network. In this topology, all traffic must cross over the controller before communication with network resources, such as a TFTP server, can occur. When converting back to non-LWAPP IOS with an access point that is no longer using the LWAPP protocol, traffic does not cross over the controller to reach the TFTP server.
Note The lightweight 1300 series access points can only be converted back to autonomous mode using a wireless LAN controller.

Getting ÿþ as saved conversations from Lync in Outlook in Office 2013

Hi,
I've been trying to get to the bottom of this and have found similar posts, but no one seems to have an answer.
When I IM someone using Lync 2013, they get a pop up notification but instead of the message they see ÿþ<. Once they open the chat window, they can see my typed text. Occasionally, certain people can't see the first line of my chat, but as
long as they keep the chat window open, they can see everything new I type.
All my conversations that are saved in outlook show ÿþ< for the text and are unreadable. I've disabled the saving of conversations because they have become worthless.
I believe it has to do with BOM but have not been able to find a way to fix this.
If I copy a conversation from the chat window and paste it into Microsoft Word it shows ÿþ<, but if I paste it into notepad the conversation appears.
(I had inserted a screenshot here, but am unable to because I am unable to figure out how to get my account "verified")
I've tried changing the preferred encoding for outgoing messages: to Unicode (UTF-8) in Outlook, but this had no effect and I can't find a similar option in Lync 2013.
(I had inserted a screenshot here, but am unable to because I am unable to figure out how to get my account "verified")
I enabled logging for Lync and the event IDs that come up are 1, 11 and 12, to which I cannot find any information for at the moment.
Any help and or suggestions would be appreciated.

Hi,
Did the issue happen only for you or for multiple users?
Please try to delete Lync User Profile and information on Registry, then repair Office 2013.
The path of Lync User Profile: %UserProfile%\AppData\Local\Microsoft\Office\15.0\Lync
The path for information on Registry: HKCU\Software\Microsoft\Office\15.0\Lync\[email protected]
Then test the issue again.
Best Regards,
Eason Huang
Eason Huang
TechNet Community Support

Project Conversion from 11.03 to R12- need help

Hi All,
I need some information regarding conversion from 11.03 to R12 along with Capital Project's conversion, do we need to take care Asset Assignment and Assets information at the time of Project Conversion. Iam doing Project and Task conversion different. Is there any good mapping document or Conversion FD, if any body have please send my mail ID. [email protected]
Thanks for your help.
Thanks,
Srini..

Usually only Open Invoices and Unapplied Receipts are migrated from Old system to New Instance.
Post Migration Reconciliation shall be tough in that scenario. Reconsider/Rediscuss with Client.
Migration can be done using APIs or Custom Scripts using Standard Interfaces.
Hope this is helpful
Regards,
Sridhar

Since downloading Firefox 4, I am having problems archiving gmail conversations from my inbox view. Also, when I go to enter a new event in google calendar, I now have to click the cursor in the box to type the event (it used to let me just start typing).

Since downloading Firefox 4, I am having problems archiving gmail conversations from my inbox view (either one or several conversations) as it says "No Conversations Selected" when I have selected one or several. Also, when I go to enter a new event in google calendar, I have to click the cursor in the box to type the event (it used to let me just start typing) or else it flips out and starts jumping to day view or another month. Does anyone know how to fix either of these?

I have had this problem; but while trying to fix another problem, I reset my preferences for Firefox and it fixed this problem as well. To reset preferences, follow this link: http://support.mozilla.com/en-US/kb/Resetting%20preferences

How can I print a text message conversation from my iPhone? Not using screenshots.

How can I print a text message conversation from my iPhone? Not using screenshots. It's around 500 messages so screenshots is not a option.

Yes, you can delete from iphone:
http://manuals.info.apple.com/enUS/iPhone_iOS4_UserGuide.pdf
It is covered in the manual.
Page 172:
"Delete a podcast: In the Podcasts list in iPod, swipe left or right over the podcast, then
tap Delete. "

Page numbers incorrect after conversion from Excel to pdf

Page numbers incorrect after conversion from Excel to pdf
""This above link (thread:834599) is from a case back in 2011 that claims to solve this problem, but it does not solve this problem. I think that customer only cared about having continuous page numbering, not discrete page numbering per sheet.
========================
I still have this issue in Acrobat XI and MS Office Professional Plus 2010. I keep upgrading to no avail. This regression has resulted in a huge time drain for me. If you fixed it, please explain how I can get my hands on the resolution.
Previous versions of Excel and Adobe Acrobat enabled flexibility around the "Page #" of "Number of Pages" (Page &[Page] of &[Pages]) token, depending on context and usage. The "# of pages" token could represent EITHER the number of pages in the workbook OR the number of pages in the tab/sheet, depending on how you generated the PDF:
You could select "Selected Sheets" and then select all or some of the individual sheets in the workbook, and the PDF would honor the discrete numbering of each of the sheets, so the first page of each sheet was p1 and the "# of pages" was the number of pages in the sheet; not the number of pages in the workbook; or
You could select "Entire Workbook" and the PDF would honor continuous page numbers across all sheets, as a single document.
Now, it only honors the total number of pages in the workbook, regardless of the method you use to publish to PDF: saving as PDF, printing to PDF, using "createPDF" from Acrobat plugin to Excel's menu ribbon; selecting all sheets, some sheets, or Entire Workbook; automatic First page number or "1" under Page Setup > Page> First page number. (This last option, btw, does restart every sheet at p1, but it hardly makes sense if the total number of pages is still the total number in the workbook instead of the number in the sheet.)
I spent a lot of time trying each which way that the blog posts recommended and have tried this on multiple versions of Excel and Acrobat now.
NONE of these time-consuming experiments gave me what I wanted.They all insist that "Page #" of "Number of Pages" (Page &[Page] of &[Pages]) is the total number of pages in the workbook or the total number of pages in the selected sheets combined.
The numbering are correct in Excel Page Layout.
The same issue happens when using LibreOffice calc. (Although, I never tested with Libre Office before, so I don't know that it ever worked).
The workaround now is to create PDF for each spreadsheet one at a time, and then compile them using the Acrobat combine/binder feature. All alternatives are extremely time consuming and tedious. It used to be automatic. This is a major regression that has gone untreated for over a year now, maybe two years.
My task takes infinitely more time to complete than it did with previous versions of Acrobat. That means that days are added to my project, when the functionality used to enable a quick pdf generation that was ready for review, now I have to do this very manual time-consuming set of steps to generate a draft. As the project has grown and more tabs are added, my pdf-generation task takes that much longer. We require lots of drafts. It used to be easy and fast. Now it is hard and time-consuming.
In my opinion, the problem is not Excel; it is Acrobat because it was introduced with an upgrade in Acrobat, not an upgrade in Excel. The problem was introduced in Acrobat 9 or 10. Please provide a patch or add-on or something.

If you are setting up the page numbers in Excel, the resulting PDF would display the the page numbers created in Excel. On Excel 2010 support page, (http://office.microsoft.com/en-us/excel-help/insert-and-remove-page-numbers-on-worksheets- HA010342619.aspx#BM2) is stated the following "tip" which indicates by default Excel 2010 starts numbering each tab with 1. Exel's workaround tip is below -
Set a different number for the starting page
Tip To number all of the worksheet pages in a workbook sequentially, first add page numbers to all worksheets in a workbook, and then use the following procedure to begin the page number for each worksheet with the appropriate number. For example, if your workbook contains two worksheets that with both be printed as two pages, you would use this procedure to begin the page numbering for the second worksheet with the number 3.
On the Page Layout tab, in the Page Setup group, click the Dialog Box Launcher next to Page Setup.
On the Page tab, in the First page number box, type the number that you want to use for the first page.
Tip To use the default numbering system, type Auto in the First page number box.
Also helpful in the same section is the note on viewing page numbers. To see if the page numbering dilemma originates in Excel make sure you are using the Page Layout View see below:
Hide All
If you want numbers shown on pages when you print a worksheet you can insert page numbers in the headers or footers of the worksheet pages. Page numbers that you insert are not displayed on the worksheet in Normal view — they are shown only in Page Layout view and on the printed pages.
Overall it may be easier not to create the page numbers in Excel but instead create then in Acrobat using the Headers and Footers option in Acrobat. I hope this helps - it sounds like a frustrating issue you are experiencing.

I can´t sync iCal events written in the iphone4 to the macbook ical, but conversely from macbook to iphone there´s no problem, can somebody help me?

I can´t sync iCal events written in the iphone4 to the macbook ical, but conversely from macbook to iphone there´s no problem, can somebody help me?

Thanks for your answer! I tried as you say, erase the Sync History, but now does not sync any calendar, only displays the birthday ...do not know whatelse to try.

Conversion from Lightweight to Autonomous

Similar Messages

Maybe you are looking for