Correlation between cpu load and the run queue

We are seeing cases where our cpu utilization is less than 50 % but we are getiing run queues of more than 10 minutes. I would expect a high run queue if we were seeing higher cpu utilization but I am having trouble correlating a high run queue with low cpu utilization. Has anyone else seen a condition like this or have any insights. Database is 11g RAC Exadata X2 full rack. We are using ORM to manage CPU resources as well.

We are seeing cases where our cpu utilization is less than 50 % but we are getiing run queues of more than 10How many cores do you have?
If 4, then it looks OK.
Even if 8, it may be correct.
The core does not pickup a waiting thread right after a running thread starts waiting for something like I/O. The switching of context has a cost.
A time of delay may depend on CPU and kernel scheduler, but generally it should be some delay after CPU switches context from one process/thread to another, in case when a running process started waiting prematurely in the middle of its time slice. That is why you may see less than 100% CPU utilization.

Similar Messages

Relation between CPU load and # of users

Dear all :
is their a relation between # of cpus and cpu load
if i have 100 concurent user how many cpu should dedicated to it ?

from where can i get benchmark?From your brain.
If I give you a benchmark, it will be valid with my load, not yours. You need to create a benchmark that reflects your load.
I have no idea what kind of load you have. Nor does anyone else ...
... unless you have a OTS or COTS application (Off The Shelf or Customized Off The Shelf). In which case your vendor (or developer) should have some clue.
(Refraining from comments about the majority of developers ...)

Permanent high CPU load and timeouts in communication channels

Dear Colleagues,
we've a strange issue since last week. At first we had an problem with a redirect to the cytrix online booking engine within the travel management application of our SAP NW Portal. There is a redirect.jsp file deployed in our PI system that connects to cytrix and passes the URL with session link and session cookie to our Portal. We fixed that issue by restarting the PI system.
We have a PI 7.0 stack 23 on HP-UX.
After restarting we found that we've got a very high CPU load (about 75% overall CPU, or 300% at 4 CPUs) probably caused by very frequent (3 per second) minor garbage collection runs (as seen in GC.log).
On friday we had timeouts within one of our communication channels in the PI system.
We changed the heap size from 2GB to 3GB and the new generation from 341MB to 768MB and restarted the PI system. But after a few ours the system uses 75% RAM of the CPU high CPU load and the GC runs are still the same.
This is a short excerpt of our GC.log:
52645.608: [GC 52645.608: [DefNew: 395326K->2003K(589824K), 0.0334788 secs] 1628688K->1235472K(2949120K), 0.0335882 secs]
52646.071: [GC 52646.072: [DefNew: 395219K->2072K(589824K), 0.0351584 secs] 1628688K->1235680K(2949120K), 0.0353002 secs]
52646.665: [GC 52646.665: [DefNew: 395288K->2173K(589824K), 0.0371023 secs] 1628896K->1236058K(2949120K), 0.0372198 secs]
52647.022: [GC 52647.022: [DefNew: 395389K->1969K(589824K), 0.0352723 secs] 1629274K->1235991K(2949120K), 0.0353865 secs]
52647.368: [GC 52647.368: [DefNew: 395185K->1885K(589824K), 0.0346132 secs] 1629207K->1235944K(2949120K), 0.0347310 secs]
52647.804: [GC 52647.804: [DefNew: 395101K->2069K(589824K), 0.0357804 secs] 1629160K->1236129K(2949120K), 0.0358980 secs]
52648.327: [GC 52648.328: [DefNew: 395285K->2285K(589824K), 0.0380093 secs] 1629345K->1236369K(2949120K), 0.0381374 secs]
52648.737: [GC 52648.738: [DefNew: 395501K->2282K(589824K), 0.0365516 secs] 1629585K->1236400K(2949120K), 0.0366749 secs]
52649.125: [GC 52649.125: [DefNew: 395498K->2435K(589824K), 0.0352310 secs] 1629616K->1236589K(2949120K), 0.0353407 secs]
52649.462: [GC 52649.462: [DefNew: 395651K->2436K(589824K), 0.0361161 secs] 1629805K->1236654K(2949120K), 0.0362322 secs]
52649.840: [GC 52649.840: [DefNew: 395652K->2322K(589824K), 0.0341640 secs] 1629870K->1236539K(2949120K), 0.0342721 secs]
Does anyone know what can cause the high load?
Is the frequency of the GC runs normal?
Can the timeouts be connected to the high CPU load?
The error ony occurs on our productive system.
I'd appriciate your help very much.
Kind regards,
Paul

hi Paul,
I believe an issue like that needs to be done onsite and not via a forum
as it probably requires doing lots of checks/tests
my suggestion would be to get a PI consultant expert with basis experience onsite or do it via OSS with SAP
Regards,
Michal Krawczyk

High CPU load and com.apple.ImageCaptureExtension2 crash after upgrade

After upgrading my Macbook Air from Lion to Mountain Lion, the system has a very high cpu load, and the crash reporter is the process that causes thee high load. In the error log I see this entry several times per second:
17.08.12 12:58:46,011 ReportCrash[5998]: com.apple.message.domain: com.apple.crashreporter.writereport.crash
com.apple.message.signature: Image Capture Extension
com.apple.message.signature2: com.apple.ImageCaptureExtension2 ||| 8.0 (8.0)
com.apple.message.signature3: 03A96CBDA3C85A114383537BFC5C8999
com.apple.message.result: NO
com.apple.message.summarize: YES
I investigated a bit more and recovered, that it has something to do with the printer drivers. When I remove all printers from setting, everything is fine. As soon as I add a printer (Brother MFC 9440CN printer/scanner, printer driver provided by Mountan Lion), the crash reporter starts it's work and the error log is full of those entries.
Any suggestions?
Thanks in advance,
Marcus

I did more exploration and found the cause of this, but I don't know how to fix it:
I removed all Brother and Lexmark printer drivers and rebooted (and also tested with a virtual machine using 10.8.0 as guest os that never had any printer installed). As soon as I enter the printer settings and press the "+", the crashes begin, so it looked like the bonjour one of the printers announcing themselves via Bonjour were causing this.
When watching a picture in the preview app the same happend. We have two multi function printers in our network, the already mentioned brother printer and a Lexmark X204N. Switching off the Lexmark (which wasn't installed on my Mac) solved the problem. Switching off the printer is no solution in our office (it's our fax device and main printer), but switching off mDNS on the Lexmark also solved it. But this can only be a workaround.
Is this a known problem with Lexmark devices and Mountain Lion (it works fine with machines using Lion)? Are there any fixes known? It's just the Lexmark device announing itself via Bonjour that causes trouble, even if the driver is not installed.

EXACT DIFFERENCE BETWEEN FULL LOAD AND REPAIRFULL LOAD?

HI Champ,
Can anyone explain me the exact difference between full load and Repairfull load?Give e some senario where we can go for this?Please.....
10zin

Hi,
Full repair can be said as a Full with selections. But the main use or advantage of Full repair load is that it wont affect delta loads in the system. If you load a full to a target with deltas running you again will have to initialize them for deltas to continue. But if you do full repair it wont affect deltas.
This is normally done we when we lose some data or there is data mismatch between source system and BW.
Check the OSS Note 739863 'Repairing data in BW' for all the details
Symptom
Some data is incorrect or missing in the PSA table or in the ODS object (Enterprise Data Warehouse layer).
There may be a number of reasons for this problem: Errors in the relevant application, errors in the user exit, errors in the DeltaQueue, handling errors in the customers posting procedure (for example, a change in the extract structure during production operation if the DeltaQueue was not yet empty; postings before the Delta Init was completed, and so on), extractor errors, unplanned system terminations in BW and in R/3, and so on.
Solution
Read this note in full BEFORE you start actions that may repair your data in BW. Contact SAP Support for help with troubleshooting before you start to repair data.
BW offers you the option of a full upload in the form of a repair request (as of BW 3.0B). If you want to use this function, we recommend that you use the ODS object layer.
Note that you should only use this procedure if you have a small number of incorrect or missing records. Otherwise, we always recommend a reinitialization (possibly after a previous selective deletion, followed by a restriction of the Delta-Init selection to exclude areas that were not changed in the meantime).
1. Repair request: Definition
If you flag a request as a repair request with full update as the update mode, it can be updated to all data targets, even if these already contain data from delta initialization runs for this DataSource/source system combination. This means that a repair request can be updated into all ODS objects at any time without a check being performed. The system supports loading by repair request into an ODS object without a check being performed for overlapping data or for the sequence of the requests. This action may therefore result in duplicate data and must thus be prepared very carefully.
The repair request (of the "Full Upload" type) can be loaded into the same ODS object in which the 'normal' delta requests run. You will find this request under the "Repair Request" option in the InfoPackage (Maintenance) menu.
2. Prerequisites for using the "Repair Request" function
2.1. Troubleshooting
Before you start the repair action, you should carry out a thorough analysis of the possible cause of the error to make sure that the error cannot recur when you execute the repair action. For example, if a key figure has already been updated incorrectly in the OLTP system, it will not change after a reload into BW. Use transaction RSA3 (Extractor Checker) in the source system for help with troubleshooting. Another possible source of the problem may be your user exit. To ensure that the user exit is correct, first load a user exit with a Probe-Full request into the PSA table and check whether the data is correct. If it is not correct: Search for the error in the exit user. If you do not find it, we recommend that you deactivate the user exit for testing purposes and request a new Full Upload. It If the data arrives correctly, it is highly probable that the error is indeed in the user exit.
We always recommend that you load the data into the PSA table in the first step and check the result there.
2.2. Analyze the effects on the downstream targets
Before you start the Repair request into the ODS object, make sure that the incorrect data records are selectively deleted from the ODS object. However, before you decide on selective deletion, you should read the Info Help for the "Selective Deletion" function, which you can access by pressing the extra button on the relevant dialog box. The activation queue and the ChangeLog remain unchanged during the selective deletion of the data from the ODS object, which means that the incorrect data is still in the change log afterwards. After the selective deletion, you therefore must not reconstruct the ODS object if it is reconstructed from the ChangeLog. (Reconstruction is usually from the PSA table but, if the data source is the ODS object itself, the ODS object is reconstructed from its ChangeLog). You MUST read the recommendations and warnings about this (press the "Info" button).
You MUST also take into account the fact that the delta for the downstream data targets is created from the changelog. If you perform selective deletion and then reload data into the deleted area, this may result in data inconsistencies in the downstream data targets.
If you only use MOVE and do not use ADD for updates in the ODS object, selective deletion may not be required in some cases (for example, if incorrect records only have to be changed, rather than deleted). In this case, the DataMart delta also remains intact.
2.3. Analysis of the selections
You must be very precise when you perform selective deletion: Some applications do not provide the option of selecting individual documents for the load process. Therefore, you must first ensure that you can load the same range of documents into BW as you would delete from the ODS object. This note provides some application-specific recommendations to help you "repair" the incorrect data records.
If you updated the data from the ODS object into the InfoCube, you can also delete it there using the "Selective deletion" function. However, if it is compressed at document level there and deletion is no longer possible, you must delete the InfoCube content and fill the data in the ODS object again after repair.
You can only perform this action after a thorough analysis of all effects of selective data deletion. We naturally recommend that you test this first in the test system.
The procedure generally applies for all SAP applications/extractors. The application determines the selections. For example, if you cannot use the document number for selection but you can select documents for an entire period, then you are forced to delete and then update documents for the entire period in the data target. Therefore, it is important to look first at the selections in the InfoPackage exactly before you delete data from the data target.
Some applications have additional special features:
Logistics cockpit: As preparation for the repair request, delete the SetUp table (if you have not already done so) and fill it selectively with concrete document numbers (or other possible groups of documents determined by the selection). Execute the Repair request.
Caution: You can currently use the transactions that fill SetUp tables with reconstruction data to select individual documents or entire ranges of documents (at present, it is not possible to select several individual documents if they are not numbered in sequence).
FI: The Repair request for the Full Upload is not required here. The following efficient alternatives are provided: In the FI area, you can select documents that must be reloaded into BW again, make a small change to them (for example, insert a period into the assignment text) and save them -> as a result, the document is placed in the delta queue again and the previously loaded document under the same number in the BW ODS object is overwritten. FI also has an option for sending the documents selectively from the OLTP system to the BW system using correction programs (see note 616331).
3. Repair request execution
How do you proceed if you want to load a repair request into the data target? Go to the maintenance screen of the InfoPackage (Scheduler), set the type of data upload to "Full", and select the "Scheduler" option in the menu -> Full Request Repair -> Flag request as repair request -> Confirm. Update the data into the PSA and then check that it is correct. If the data is correct, continue to update into the data targets."
Refer.
Repair full request
Re: Repair full request
Steps to perform repair full request
full repair request
repair full request
Re: Repair Full Request
Thanks,
JituK

Having lagging problems with YouTube videos, it simply takes so long for the red bar to completely load and the videos frequently pause and take too long to restart playing again.

I have been having lagging problems with YouTube videos for a number of months now. It simply takes so long for the red bar to completely load and the videos frequently pause and take too long to restart playing again. Even with little 2 and 3 minute videos.
I have a fast computer and my webpages load really, really fast. I have FireFox 4 browser and a Vista Home Premium 64-bit OS. So I don't have a slow computer or web browser. But these slow YouTube vids take way too long to load for some reason.
Does anyone have any idea how I can speed up YouTube?

Hi
The forums are customer to customer in the first instance, Only the mods (BT) will ask for personal information through a email link. Would you mind posting your Hub stats & BT speed test results this will help all with diagnosis-
To post the full stats from your router
for home hub - 192.168.1.254
Navigate to ADSL Settings or use the A-Z at the top right
Click on More Details and then post the results.
Run BT speed tester and post the results from http://speedtester.bt.com/
If possible it would be best to connect to the BT master socket this will rule out any telephone/broadband extension wiring also consider the housing of the hub/router as anything electrical can cause problems as these are your responsibility, if these are found to be the case Openreach (engineer) will charge BT Broadband, which will be passed onto you, around £130.00.
Noisy line! When making telephone calls, if so this is not good for your broadband, you can check-
Quite line test dial 17070 option 2 and listen - should hear nothing best done with old type analogue phone digital (dect) will do but may have slight hiss If you hear noise- crackling pops etc, report it as a noisy line on your phone, don’t mention broadband, Bt Faults on 151.
As for your FTTC its available in some areas between 40% & 80% of customers in enabled areas can receive it!
Mortgage Advisor 2000-2008
Green Energy Advisor 2008-2010
Charity Health Care Provider Advisor 2010-
I'm alright Jack....

A required application library failed to load and the product cannot continue

Seems like I go through this problem time and again with Photoshop + Acrobat CS2 and still have yet to resolve a way of fixing it short of completely wiping my drive and re-installing Windows (XP Pro) The error is "application library failed to load and the product cannot continue"
If there is anyone out there that has figured out a way to fix this issue please fill me in.
This time I went as far as a complete and though removal of all Adobe products from the system and the registry and then completely reinstalled the product.
I have forgone purchasing CS3 because of this issue as I am 99% sure that it has still not been resolved.
Basically Photoshop and Acrobat are useless at this point and I am using an old version of Picture Publisher and Macromedia Fireworks to complete my work. This I assume is good advertising for Adobe :)
Anyone have any ideas????
See this post in the forum "could not complete your request because of a program error", PDF format, cs2, xp" as this is an ongoing Adobe issue that they have completely blown off!
I am working on
Adobe Photoshop Version: 9.0.2 (9.0.2x296)
Operating System: Windows XP
Version: 5.1 Service Pack 2
System architecture: Intel CPU Family:15, Model:2, Stepping:9 with MMX, SSE Integer, SSE FP, SSE2, HyperThreading
Physical processor count: 1
Processor speed: 2798 MHz
Built-in memory: 2559 MB
Free memory: 1812 MB
Memory available to Photoshop: 1758 MB
Memory used by Photoshop: 55 %
Image cache levels: 6
Serial number: XXXXXXXXXXXXXXXXXX (I have a legal copy)
Application folder: C:\Program Files\Adobe\Adobe Photoshop CS2\
Temporary file path: C:\DOCUME~1\JIMSHE~1\LOCALS~1\Temp\
Photoshop scratch has async I/O enabled
Scratch volume(s):
Startup, 128.0G, 65.5G free
Primary Plug-ins folder: C:\Program Files\Adobe\Adobe Photoshop CS2\Plug-Ins\
Additional Plug-ins folder: not set
Installed plug-ins:
ADM 3.10x21
ASDStrm 1.03x2
Accented Edges 9.0
Angled Strokes 9.0
Average 9.0 (9.0x196)
BMP 9.0 (9.0x196)
Bas Relief 9.0
Camera Raw 3.7
Chalk & Charcoal 9.0
Charcoal 9.0
Chrome 9.0
Cineon 9.0 (9.0x196)
Clouds 9.0 (9.0x196)
Color Halftone 9.0 (9.0x196)
Colored Pencil 9.0
CompuServe GIF 9.0 (9.0x196)
Conditional Mode Change 9.0 (9.0x196)
Contact Sheet II 9.0 (9.0x196)
Conté Crayon 9.0
Craquelure 9.0
Crop and Straighten Photos 9.0 (9.0x196)
Crop and Straighten Photos Filter 9.0 (9.0x196)
Crosshatch 9.0
Crystallize 9.0 (9.0x196)
Cutout 9.0
Dark Strokes 9.0
De-Interlace 9.0 (9.0x196)
Difference Clouds 9.0 (9.0x196)
Diffuse Glow 9.0
Displace 9.0 (9.0x196)
Dry Brush 9.0
Embed Watermark 1.70.19
Export Transparent Image 9.0 (9.0x196)
Extract 9.0 (9.0x196)
Extrude 9.0 (9.0x196)
FastCore Routines 9.0 (9.0x196)
Fibers 9.0 (9.0x196)
Film Grain 9.0
Filmstrip 9.0 (9.0x196)
Filter Gallery 9.0
Fit Image 9.0 (9.0x196)
Fresco 9.0
Generic EPS 9.0
Glass 9.0
Glowing Edges 9.0
Grain 9.0
Graphic Pen 9.0
HDRMergeAlign 9.0x001
HDRMergeUI 9.0x001
Halftone Pattern 9.0
Ink Outlines 9.0
Lens Blur 9.0
Lens Correction 9.0
Lens Flare 9.0 (9.0x196)
Lighting Effects 9.0 (9.0x196)
Liquify 9.0
MMXCore Routines 9.0.1 (9.0.1x289)
Merge to HDR 1.0x001
Mezzotint 9.0 (9.0x196)
Mosaic Tiles 9.0
Multiprocessor Support 9.0 (9.0x196)
NTSC Colors 9.0 (9.0x196)
Neon Glow 9.0
Note Paper 9.0
Ocean Ripple 9.0
OpenEXR 9.0 (9.0x196)
PCX 9.0 (9.0x196)
PNG 9.0 (9.0x196)
PNG Icons 1.22x1
Paint Daubs 9.0
Palette Knife 9.0
Patchwork 9.0
Paths to Illustrator 9.0 (9.0x196)
Pattern Maker 9.0 (9.0x196)
Photo CD 9.0 (9.0x196)
Photocopy 9.0
Photomerge 9.0 (9.0x196)
PhotomergeCylmap 9.0 (9.0x196)
PhotomergeRender 9.0 (9.0x196)
PhotomergeUI 9.0 (9.0x196)
Picture Package 9.0 (9.0x196)
Picture

John,
foud your message very helpfull. I experience the same problem when strating a CS2 program (Photoshop, Indesign,...) over a terminal server connection.
It's weird because starting more than one instance is possible (despite what's written in the article ) as long as the users have administrative rights. I've encountererd this problem because my daughter of 11 wants to use Photoshop now. I have a terminal server set up so the kids may experiment with their own desktops whithout the risk to screw it up and because I can access all my programs from wherever I want.
But as I found out now I must buy volume licensing instead of retail (even if it's for just one instance...)
Want to know if possible how "difficult" it was to change your retail to a volume licensed version? Did you have to pay the full amount again? Hope an upgrade exist from Creative Suite CS2 - retail to Creative suite CS3 - volume licensed for the same price as from retail to retail... Or am I hoping to much?
Kind regards and thanks for your info,
Patrick

"USB device not recognized." "The connection between your device and the desktop could not be established. Please check your setup and try again." Tungsten E2, Outlook 2007

Hi,
I am running XP SP 2, on a Dell Vostro 1000, Palm OS Garnet v5.4.7 on a Tungsten E2. I have worked though issues relating to synchronization, Outlook 2007, Docs to Go, etc., in the past. Thank you board members!
Once I worked thru all the initial problems, my Tungsten E2 was sync' ing beautifully to my laptop until a few days ago. There have been no changes (I know of) to the configuration, but now I receive "The connection between your device and the desktop could not be established. Please check your setup and try again." On the laptop I sometimes get "USB device not recognized." I am unclear why I get the PC message sometimes and not others.
I have tried the following: (not necc exactly in this order)
Double checked Hot Sync Mgr settings: Local USB (ver. 6.0.1)
Reset the Palm (multiple times)
Rebooted the laptop (multiple times before and after the Palm resets)
Went to Support Libraries including http://kb.palm.com/SRVS/CGI-BIN/WEBCGI.EXE/,/?St=57,E=0000000001060189973,K=9550,Sxi=3,Case=Obj(3695...)
and http://kb.palm.com/SRVS/CGI-BIN/WEBCGI.EXE?New,Kb=PalmSupportKB,ts=Palm_External2001,Case=obj(1409)
Followed the steps in "Start Here" found at http://forums.palm.com/palm/board/message?board.id=windows_hotsync&thread.id=26057
Moved Backup directory as per a post on this forum
Looked for a deleted a file called "Graffiti_ShortCuts_____________" per a post on this forum
Followed the steps in HotSync troubleshooter guide you can run through located on
http://kb.palm.com
Went into Device Manager - found it shows no yellow ! 's
Followed Device Mgr Troubleshooter - went all the way thru with no solution
Tried all four USB ports - the PC's bell-like tone does not sound when I disconnect or reconnect the Plam's cradle like it does when I conn/disconnect other USB devices -I think that is a clue. ...?
Cleaned the Palm's contacts (and cradle's contacts with a old, dry toothbrush)
Read all the posts under "USB device not recognized."
OK, I'm at a loss, can anyone help me? Many thanks in advance!
~Bob
Post relates to: Tungsten E2

Hello!
Using a cradle with the Tungsten E2? Tried bypassing the cradle and just use the hotsync cable? Tried a different computer yet? Somehow, the PC is having problems getting a signal from the device. I assume you have the laptop charger plugged into the laptop during this? Not going through a docking station or port-replicator.
One crazy thing you can try is unplug the charger from your laptop, remove the battery from the laptop and leave it out for like 10mins and put it back in and reboot the laptop. This should not cause side effects but still contact your OEM to make sure that nothing else is needed after leaving the battery out for extended period of time. Keep me posted.
Post relates to: Treo 650 (Unlocked GSM)

What's the difference between Java SDK and the Enterprise Edition?

What's the difference between Java SDK and the Enterprise Edition? Are they both free?

both r free but they are used in diffrent applications. sdk are used for simple apps that run on your computer while j2e (enterprise edition) are ment for large distributed computer systems that include servers and such. if you don't know the diffrence you probably wont need the the j2e, only the sdk.

Customise table inconsistency between ABAP Dictionary and the databas

Hi all,
I have encountered a problem where by, I was not able to activate a table due to inconsistency between ABAP Dictionary and the database.
After I run the SE14--> Check Database object. It has show that there is a missing Unique Index(Primary Index) at the Database Level, but at ABAP Dictionary it is there.
I have try to recreate the primary index at the Database level, but failed. Because one of the primary key field is been dropped from this table.
So now, may I know how can I still make this table Active again?
Is it save to folllow the following solution that I found on internet?
Syntax error in SDCC, table inconsistency between ABAP Dictionary and the database, transport error 8 during the generation of ABAP Dictionary. When you call Transaction SDCC, a termination occurs due to a putative syntax error because a table is not known or active. When you check this with the ABAP dictionary (SE11), you notice, that the table is active or inactive, however it is not possible to activate it. The activation might terminate with the error message 'Inconsistency between ABAP Dictionary and database'. A check of the affected object also delivers this error.
Solution
Proceed as follows:
Log on as user DDIC
Call Transaction SE14
Enter the affected table name and
select EDIT
In the following screen, choose Table -> Reconstruct
Confirm the execution
Call Transaction SE11
Enter the affected table name
Display
Activate
Thanks.
CK

I managed to solved this by
Solution
Proceed as follows:
Log on as user DDIC
Call Transaction SE14
Enter the affected table name and
select EDIT
In the following screen, choose Table -> Reconstruct
Confirm the execution
Call Transaction SE11
Enter the affected table name
Display
Activate
Thanks.
CK

Correlation between BI developer and Web Analyst?

These days, I'm studying to become a business intelligence developer and today I'm reflecting If I need necessary knowledge as a web analyst.
My question is.
Is there a correlation between BI developer and web analyst If yes, should I also gain skills as a web analyst?

Hi Sakura,
The largest part of any analyst role is understanding the clients needs / business requirements and being able to help translate those requirements into functional specifications. The best analysts I have worked with are the ones that know the product
and what it can do. In addition, we will see more business intelligence applications deliver or render results to the web enabled portals like SharePoint 2013.
As a developer the more you understand a clients needs and are able to meet those needs either OOB, third party, or custom code the more valuable you will become in being able to know where the holes are and being able to fill them,
-Ivan
-Ivan

I have an Apple MacBook Pro with 2 USB ports and a MiniDisplay Port. I also have an HDTV with a HDMI port. How can I use the TV as a display without any tethering wires between my computer and the TV?

I have an Apple MacBook Pro with 2 USB ports and a MiniDisplay Port. I also have an HDTV with a HDMI port. How can I use the TV as a display without any tethering wires between my computer and the TV? I have a MiniDisplay Port to VGA adapter, but there are two issues with it: The new display doesn't have a VGA port, and even if it did, I wouldn't want to have my mac constantly attached to the display by a cable. I was looking for a way to use the TV as a display without any wires. Is there some type of bluetooth setup I could use? Please let me know if you have any suggestions.

As I wrote above, I think you should look into the Apple TV yourself. The best place to find information about what it can and can't do and to ask your own specific questions is probably in the Apple TV forum, here:
https://discussions.apple.com/community/appletv/appletv

Data reconciliation between R/3 and the BW Systems

How do we do data reconciliation between R/3 and the BW system for the following areas?
Purchasing
Controlling:
Project System:
COPA
SD
AP
Trgards,
Tony G

Tony
Have you looked these documents??
https://www.sdn.sap.com/irj/servlet/prt/portal/prtroot/com.sap.km.cm.docs/library/biw/how%20to%20validate%20infocube%20data%20by%20comparing%20it%20with%20psa%20data
https://www.sdn.sap.com/irj/servlet/prt/portal/prtroot/docs/library/uuid/7a5ee147-0501-0010-0a9d-f7abcba36b14
Re: BW v. R/3 data reconciliation
Hope this helps
Thanks
Sat

Updated to ios 6 and now when i go to the app store and try to check out my purchased it try to load the information but after about 20-25 seconds nothing loads and the app crashes. Im not sure if its because i have at least 600 apps in the cloud.

WIth my iphone 4 in ios 6 when i try to view my puchased in the app store app it starts to load and after about 20-25 seconds nothing loads and the app crashes im wondering if its because i have at least 600 apps in there, but it has never happened to be before.

WIth my iphone 4 in ios 6 when i try to view my puchased in the app store app it starts to load and after about 20-25 seconds nothing loads and the app crashes im wondering if its because i have at least 600 apps in there, but it has never happened to be before.

How do I close multiple documents opened in Finder when the files are loading and the Application is not responding?

I was moving 90 files from one folder to another and instead accidently double clicked all the files I had selected and they all opened at once and now they are all stuck trying to load and the program is not responding.
When I put my mouse over the folders, it's just the loading cursor so i can't select anything. I've tried using 'command' - 'option' - 'W' and that doesn't work either.
I have tried restarting finder and all that does is shut all of the folders and reopens them and they get stuck trying to load all over again.
I have tried restarting my macbook and every time I log back in, it restarts all the programs and all the finder windows and the whole process repeats.
(even when I unselect the 'restart opened programs' box.)
I really hope someone knows how to troubleshoot this problem I am having!

You're trying to use Spry Accordions for something they were never intended to do. Why don't you switch to a more appropriate jQuery Mega Menu?
http://www.designchemical.com/lab/jquery-mega-drop-down-menu-plugin/examples/
In case you missed the announcement, Spry is dead. Adobe abandoned it late last year because it has outlived its usefulness.
http://blogs.adobe.com/dreamweaver/2012/08/update-on-adobe-spry-framework-availability.htm l
Nancy O.

Correlation between cpu load and the run queue

Similar Messages

Maybe you are looking for