Create a Graph with only one set of data? Threw serial

I feel this is a simple question, but I am over thinking it. I am trying to make a program that takes data that is sent threw serial Rs232 from a device, and put that data both into a file and display a live graph of the data (saving the graph would also be great). The devise is strait forward it gives me data when it is don't making the test. After it has the data is sends it and it is always in this form, (ignore Quotes) "[ 122.8 PSI ]' where "122.8" will always be 5 characters and the decimal point stays the same.
I would like to take Ex. 122.8 and plot that on y and use the line number from the text file as the x value. How can this be achieved?
Currently I am displaying the values in a list because I can't figure the graph out. But attached is my messy code and a sample of data that gets sent.
P.S.. The data list can get as long as 2000 or more.
side question... when the program is built into an EXE when using serial, can the user change what port?
Attachments:
test 1.vi ‏20 KB
test 1.txt ‏1 KB
test 1 graph.txt ‏1 KB

Well, that's called Rube Golberg code.
All that you have to do is convert the string to a numeric (i.e. a single Scan From String not your match pattern functions) and wire it to a chart. The chart's x axis by default will increment by 1 with each sample written so reading the x axis from file is silly. Be sure to set the chart history. Since you are already writing the data to file, why write it again? Either write the full string or just the value. Your second while loop becomes unnecessary and if for some reason you needed it, it would only record the very last value.
Don't open the file with each iteration. Place that outside the loop.
You might want to take the free LabVIEW tutorials.

Similar Messages

How to evolve a graph with only one loop

1. how to continue to add new nodes to a graph with only one loop
would like to use graph traversal like my previous post to traversal a binary tree, but this time, it can
loop forever, i mean it traverse all nodes in whole graph in the meanwhile it add new nodes too
assume maximum number of joint is 2 or 3
computing nightmare

I just realised that you weren't talking about cyclic graphs (in the case of 1 cycle) here, but meant a single pass traverse and mutate.
What you don't specify is how the new nodes are being supplied. If they are supplied up front, then the loop will of course terminate once all the inputs are addressed, rather than going on forever. If they are being supplied from time-to-time,
then you need to have some sort of event-wait on input. The traversal could have a move-next something like this
If at end of tree with no new nodes, wait for input
If at end of tree, with input, reset to start
If at insertion point for new node at top of input queue, insert that
Move to next node in tree
This seems the sort of thing that would naturally be coded in a functional language as a tail recursion rather than an iteration.

How to plot a log graph using grapher with a given set of data

hi there,
im just wondering is it possible to plot a log graph in the grapher software with a given set of data, and also give an error bar and a best-fit line for it?
so here is the set of data,
Concentration of BCh (M)
Mean % Specific Binding (%)
Standard Deviation
3 ×10⁻⁹
71.52
9.52
1 ×10⁻⁸
57.30
8.56
3 ×10⁻⁸
39.15
9.40
1 ×10⁻⁷
24.13
10.15
3 ×10⁻⁷
14.77
3.31
1 ×10⁻⁶
7.22
2.02
hope someone could help

Try these:
http://y.barois.free.fr/grapher/Bienvenue.html
http://homepage.mac.com/tlindywizdumb/math/Grapher_index.htm
http://homepage.mac.com/tlindywizdumb/math/Grapher/Grapher_HowTo.pdf

How to update multi-handle graph with a new set of data points

I have multiple sets of data that all have the same number of columns but different numbers of rows. Each column is plotted on a graph. I want to keep the format of the original graph with the same number of handles, and update each handle with new data points by bringing in a new set of points.
See attachment for example.
Attachments:
hiqgraph.HiQ ‏14 KB

There are several ways to do this.
1. You can create a HiQ script that plots the new data to the graph using the existing plots. The following three lines plot the new data into the three existing plots (indicated by the plot handles.) Put these lines into a HiQ script object, right-click and select Run.
addplot(Graph2D_1,-1,data2[*,1],data2[*,2]);
addplot(Graph2D_1,-2,data2[*,1],data2[*,3]);
addplot(Graph2D_1,-3,data2[*,1],data2[*,4]);
2. You can do it interactively by right-clicking on the individual plots and choosing Change... This will being up a dialog you can use to change the data in that plot. This will be difficult to do when plots are right on top of each other, so you may want to display the plot legend, where you can also right-click a
nd select Change...
3. I like your idea about DataSocket. This way it will happen automatically. Whenever the matrix published to DataSocket changes, the plot should automatically update.
I hope this helps.
David

Create many SIA with only one installation issue

Hi,
I want create many CMS linked to corresponding SIA in one install.
For sample, we have:
PRG -->CMS 6400
TST -->CMS 6500
In the install, The SIA for PRG is autolmatically created.
After this, I have created a new database in Mysql for TST.
I have used command for create a new SIA :
./addnode.sh -name SIATST -siaport 6411 -cms boxi:6400 -user Administrator -password PRG
I have launched the command :
./cmsdbsetup and respond the name of the new SIA --> SIATST
I have 'updated' the datadase info and reinitialize the database. At this time, the CMS port is asked and I have respond 6500.
Like explain at the end of the tool, I have launched the command:
./ccm.sh -updateobjects -cms boxi:6500
After start the SIATST, I can connect to the CMS:6500 and all services is connected to the port 6500 (in the command line -ns boxi:6500).
Unluckily, the <node> name SIATST is always present in SIAPRG (cms on 6400) but on failed to start.
I have tried to remove this by command:
./removenode.sh -name SIAPRG -cms boxi:6400 -username Administrator -password PRG
I have the error:
Logging on to boxi:6400 as user Administrator with secEnterprise authentication...
The SIA on this machine with the name SIATST doesn't exist in the cluster you are connected to.
In the 'Server' tab in the CCM interface, I have always this node information and all services linked.
It's possible to remove this SIATST on SIAPRG ?
This procedure is good for wanted solution ?
Thanks
Gilles
Edited by: Gilles Crebassa on Oct 8, 2010 9:00 AM

Why two primary that is 'coz geographically based server support and workstation. You can think it as a data center to data center split.
That doesn't make sense and aren't valid reasons for 2012 (not that you can necessarily change it now).
This line jumps out at me in the log file though: "An MP exists on this machine".
That looks like the system you are installing on previously had an MP on it. I would delete the ccm namespace in WMI, cleanup all reference to ccm and Configuratin Manager from the registry, and then try again.
Jason | http://blog.configmgrftw.com | @jasonsandys

Creating a class with only one method in it

Do you think it is worth creating a class if you only have one method in it?
Or do you think i should just put it in the class that contains the main method?
Just wondering.
Thank you.

lol, what does it depend on.
The class i am talking about, is to register new
customers, A class is typically a noun in your problem description - so the class could be Customer, or maybe Registry. But "register new customers" is an action, so this should be a method, and it should belong to whatever class in your system you think should have the responsibility to register new custromers.
a pretty major part of the application.
But is it really required to have it's own class?
If it still depends, what does it depend on?

Load balancing with only one Real Server on CSM

Other than create a VSERVER with only one real server in it - is there a way of load balancing when you have only one real server now and may be additional servers to be added later?

the only way is to use the vserver.
Gilles.

Declare the internal table with only one 10 character field and use

Hi,
I want to declare the internal table with only one 10 character field and use.
Jaya

Hi,
Go ahead. U can declare IT with only one field
Example:
data: begin of zcustlist occurs 1000,
custmer(10) type c,
end of zcustlist.
Narendra Reddy.
Edited by: Narendra Reddy C on Aug 8, 2008 11:39 AM

Create multiple portal instances with only one database?

Can someone create multiple portal instances with only one database?
If so, how is this done, just by running the portal configuration wizard?
How are most people running with multiple developers working on portal? Do they share a portal instance, or create their own?
Thank you very much!
Phillip

i'm currently using 9ias rel 2(9.0.2) and i have install one infrastructure and two mid tier, hoping that this will create two portal, but it didn't. Can you please tell me how to do create two portal within one server.
thanks and regards;
andrew

SQL Server 2012 Undetected Deadlock in a table with only one row

We have migrated our SQL 2000 Enterprise Database to SQL 2012 Enterprise few days ago.
This is our main database, so most of the applications access it.
The day after the migration, when users started to run tasks, the database access started to experiment a total failure.
That is, all processes in the SQL 2k12 database were in lock with each other. This is a commom case of deadlock, but the Database Engine was unable to detect it.
After some research, we found that the applications were trying to access a very simple table with only one row. This table has a number that is restarted every day and is used to number all the transactions made against the system. So, client
applications start a new transaction, get the current number, increment it by one and commit the transaction.
The only solution we found was to kill all user processes in SQL Server every time this situation occurs (no more than 5 minutes when all clients are accessing the database).
No client application was changed in this migration and this process was working very well for the last 10 years.
The problem is that SQL 2k12 is unable to handle this situation compared to SQL 2k.
It seems to occurs with other tables too, but as this is an "entry table" the problem occurs with it first.
I have searched internet and some suggest some workarounds like using table hints to completely lock the table at the begining of the transaction, but it can't be used to other tables.
Does anyone have heard this to be a problem with SQL 2k12? Is there any fixes to make SQL 2k12 as good as SQL 2k?

First off re: "Unfortunatelly, this can't be used in production environment as exclusive table lock would serialize the accesses to tables and there will be other tables that will suffer with this problem."
This is incorrect.
Using a table to generate sequence numbers like this is a bad idea exactly because the access must be serialized. Since you can't switch to a SEQUENCE object, which is the correct solution, the _entire goal_ of this exercise to find a way to properly
serialize access to this table. Using exclusive locking will not be necessary for all the tables; just for the single-row table used for generating sequence values with a cursor.
I converted the sample program to VB.NET:
Public Class Form1
Private mbCancel As Boolean = False
Private Sub Button1_Click(sender As Object, e As EventArgs) Handles Button1.Click
Dim soConn As ADODB.Connection
Dim soRst As ADODB.Recordset
Dim sdData As Date
Dim slValue As Long
Dim slDelay As Long
'create database vbtest
'go
' CREATE TABLE [dbo].[ControlNumTest](
' [UltData] [datetime] NOT NULL,
' [UltNum] [int] NOT NULL,
' CONSTRAINT [PK_CorreioNumTeste] PRIMARY KEY CLUSTERED
' [UltData] Asc
' )WITH (PAD_INDEX = OFF, STATISTICS_NORECOMPUTE = OFF, IGNORE_DUP_KEY = OFF, ALLOW_ROW_LOCKS = ON, ALLOW_PAGE_LOCKS = ON, FILLFACTOR = 80) ON [PRIMARY]
' ) ON [PRIMARY]
mbCancel = False
Do
' Configure the Connection object
soConn = New ADODB.Connection
With soConn
.ConnectionString = "Provider=SQLNCLI11;Initial Catalog=vbtest;Data Source=localhost;trusted_connection=yes"
.IsolationLevel = ADODB.IsolationLevelEnum.adXactCursorStability
.Mode = ADODB.ConnectModeEnum.adModeReadWrite
.CursorLocation = ADODB.CursorLocationEnum.adUseServer
.Open()
End With
' Start a new transaction
Call soConn.BeginTrans()
' Configure the RecordSet object
soRst = New ADODB.Recordset
With soRst
.ActiveConnection = soConn
.CursorLocation = ADODB.CursorLocationEnum.adUseServer
.CursorType = ADODB.CursorTypeEnum.adOpenForwardOnly
.LockType = ADODB.LockTypeEnum.adLockPessimistic
.Open("SELECT * FROM dbo.ControlNumTest")
End With
With soRst
sdData = .Fields!UltData.Value ' Read the last Date (LOCK INFO 1: See comments bello
slValue = .Fields!UltNum.Value ' Read the last Number
If sdData <> Date.Now.Date Then ' Date has changed?
sdData = Date.Now.Date
slValue = 1 ' Restart number
End If
.Fields!UltData.Value = sdData ' Update data
.Fields!UltNum.Value = slValue + 1 ' Next number
End With
Call soRst.Update()
Call soRst.Close()
' Ends the transaction
Call soConn.CommitTrans()
Call soConn.Close()
soRst = Nothing
soConn = Nothing
txtUltNum.Text = slValue + 1 ' Display the last number
Application.DoEvents()
slDelay = Int(((Rnd * 250) + 100) / 100) * 100
System.Threading.Thread.Sleep(slDelay)
Loop While mbCancel = False
If mbCancel = True Then
Call MsgBox("The test was canceled")
End If
Exit Sub
End Sub
Private Sub Button2_Click(sender As Object, e As EventArgs) Handles Button2.Click
mbCancel = True
End Sub
End Class
And created the table
CREATE TABLE [dbo].[ControlNumTest](
[UltData] [datetime] NOT NULL,
[UltNum] [int] NOT NULL,
CONSTRAINT [PK_CorreioNumTeste] PRIMARY KEY CLUSTERED
[UltData] Asc
)WITH (PAD_INDEX = OFF, STATISTICS_NORECOMPUTE = OFF, IGNORE_DUP_KEY = OFF, ALLOW_ROW_LOCKS = ON, ALLOW_PAGE_LOCKS = on, FILLFACTOR = 80) ON [PRIMARY]
) ON [PRIMARY]
go insert into ControlNumTest values (cast(getdate()as date),1)
Then ran 3 copies of the program and generated the deadlock:
<deadlock>
<victim-list>
<victimProcess id="processf27b1498" />
</victim-list>
<process-list>
<process id="processf27b1498" taskpriority="0" logused="0" waitresource="KEY: 35:72057594039042048 (a01df6b954ad)" waittime="1970" ownerId="3181" transactionname="implicit_transaction" lasttranstarted="2014-02-14T15:49:31.263" XDES="0xf04da3a8" lockMode="X" schedulerid="4" kpid="9700" status="suspended" spid="51" sbid="0" ecid="0" priority="0" trancount="2" lastbatchstarted="2014-02-14T15:49:31.267" lastbatchcompleted="2014-02-14T15:49:31.267" lastattention="1900-01-01T00:00:00.267" clientapp="vbt" hostname="DBROWNE2" hostpid="21152" loginname="NORTHAMERICA\dbrowne" isolationlevel="read committed (2)" xactid="3181" currentdb="35" lockTimeout="4294967295" clientoption1="671088672" clientoption2="128058">
<executionStack>
<frame procname="adhoc" line="1" stmtstart="80" sqlhandle="0x020000008376181f3ad0ea908fe9d8593f2e3ced9882f5c90000000000000000000000000000000000000000">
UPDATE [dbo].[ControlNumTest] SET [UltData]=@Param000004,[UltNum]=@Param000005 </frame>
<frame procname="unknown" line="1" sqlhandle="0x0000000000000000000000000000000000000000000000000000000000000000000000000000000000000000">
unknown </frame>
</executionStack>
<inputbuf>
(@Param000004 datetime,@Param000005 int)UPDATE [dbo].[ControlNumTest] SET [UltData]=@Param000004,[UltNum]=@Param000005 </inputbuf>
</process>
<process id="processf6ac9498" taskpriority="0" logused="10000" waitresource="KEY: 35:72057594039042048 (a01df6b954ad)" waittime="1971" schedulerid="5" kpid="30516" status="suspended" spid="55" sbid="0" ecid="0" priority="0" trancount="1" lastbatchstarted="2014-02-14T15:49:31.267" lastbatchcompleted="2014-02-14T15:49:31.267" lastattention="1900-01-01T00:00:00.267" clientapp="vbt" hostname="DBROWNE2" hostpid="27852" loginname="NORTHAMERICA\dbrowne" isolationlevel="read committed (2)" xactid="3182" currentdb="35" lockTimeout="4294967295" clientoption1="671156256" clientoption2="128058">
<executionStack>
<frame procname="adhoc" line="1" sqlhandle="0x020000003c6309232ab0edbe0a7790a816a09c4c5ac6f43c0000000000000000000000000000000000000000">
FETCH API_CURSOR0000000000000001 </frame>
<frame procname="unknown" line="1" sqlhandle="0x0000000000000000000000000000000000000000000000000000000000000000000000000000000000000000">
unknown </frame>
</executionStack>
<inputbuf>
FETCH API_CURSOR0000000000000001 </inputbuf>
</process>
</process-list>
<resource-list>
<keylock hobtid="72057594039042048" dbid="35" objectname="vbtest.dbo.ControlNumTest" indexname="PK_CorreioNumTeste" id="lockff6e6c80" mode="U" associatedObjectId="72057594039042048">
<owner-list>
<owner id="processf6ac9498" mode="S" />
<owner id="processf6ac9498" mode="U" requestType="wait" />
</owner-list>
<waiter-list>
<waiter id="processf27b1498" mode="X" requestType="convert" />
</waiter-list>
</keylock>
<keylock hobtid="72057594039042048" dbid="35" objectname="vbtest.dbo.ControlNumTest" indexname="PK_CorreioNumTeste" id="lockff6e6c80" mode="U" associatedObjectId="72057594039042048">
<owner-list>
<owner id="processf27b1498" mode="U" />
<owner id="processf27b1498" mode="U" />
<owner id="processf27b1498" mode="X" requestType="convert" />
</owner-list>
<waiter-list>
<waiter id="processf6ac9498" mode="U" requestType="wait" />
</waiter-list>
</keylock>
</resource-list>
</deadlock>
It's the S lock that comes from the cursor read that's the villian here. U locks are compatible with S locks, so one session gets a U lock and another gets an S lock. But then the session with an S needs a U, and the session with a U needs an
X. Deadlock.
I'm not sure what kind of locks were taken by this cursor code on SQL 2000, but on SQL 2012, this code is absolutely broken and should deadlock.
The right way to fix this code is to add (UPDLOCK,SERIALIZABLE) to the cursor
.Open("SELECT * FROM dbo.ControlNumTest with (updlock,serializable)")
So each session reads the table with a restrictive lock, and you don't mix S, U and X locks in this transaction. This resolves the deadlock, but requires a code change.
I tried several things that didn't require a code, which did not resolve the deadlock;
1) setting ALLOW_ROW_LOCKS=OFF ALLOW_PAGE_LOCKS=OFF
2) SERIALIZABLE isolation level
3) Switching OleDB providers from SQLOLEDB to SQLNCLI11
Then I replaced the table with a view containing a lock hint:
CREATE TABLE [dbo].[ControlNumTest_t](
[UltData] [datetime] NOT NULL,
[UltNum] [int] NOT NULL,
CONSTRAINT [PK_CorreioNumTeste] PRIMARY KEY CLUSTERED
[UltData] Asc
)WITH (PAD_INDEX = OFF, STATISTICS_NORECOMPUTE = OFF, IGNORE_DUP_KEY = OFF, ALLOW_ROW_LOCKS = ON, ALLOW_PAGE_LOCKS = on, FILLFACTOR = 80) ON [PRIMARY]
) ON [PRIMARY]
go
create view ControlNumTest as
select * from ControlNumTest_t with (tablockx)
Which, at least in my limited testing, resovlved the deadlock without any client code change.
David
David http://blogs.msdn.com/b/dbrowne/

Multiple events per date with only one photo each - Unwanted

I have the eyefi wireless sd card in my camera and it is setup to transmit my photos into iphoto automatically, which it does. However, the problem arises in that iphoto creates multiple events for the same date each containing only one photo. I would prefer that iphoto create individual events per date and have the multiples of that date's photos within. I thought I had the settings configured to do so as I have preferences set for autosplit events one per day but I still see events such as - July 3, 2008 - July 3, 2008 - July 3, 2008 - each with only one photo inside.
I am wondering if it is something in iphoto's settings or the way in which eyefi transmits the photos into iphoto.
Any thoughts?

I do not have a WiFi connection to my camera so can not test but am just guessing
I can think of two possibilities
- 1 - if you are taking the photos with the WiFi connected then each time you snap a photo it may be being sent which would be looked at as a new import and therefore create a new event - to stop this I believe you would have to not have a full time WiFi connection to your camera or somehow set the camera to send batched - not each one - iPhoto will take each batch into and follow the rules for making events for that batch even if you camera is sending many batches of One photo
- 2 - You have the preference for making batches set to one every two hours and there is a long time between photos - I'm guessing that #1 is more likely
LN

SQL query to retrieve families with only one generation from a family db

Hi,
I need to write an SQL query that would select families with only one generation ((which means a person - or a married couple - with kids) or (a person - or a married couple - with parents but no kids)) from a database containing families. The simplified db structure is:
person:
id - int, primary key
siblings:
id
parent_id
kid_id
marriage
id:
husband_id
wife_id
Could anyone please help me? I dont really have any idea how to accomplish that...

Hi,
Welcome to the forum!
Assuming that siblings (despite its name) contains only parent-child relationships, and that the parent_id could be either the mother or the father:
WITH     got_tree     AS
     SELECT     CONNECT_BY_ROOT s.parent_id     AS root_id
     ,     LEVEL                     AS lvl
     FROM          siblings     s
     LEFT OUTER JOIN     marriage     m     ON     s.parent_id     IN ( m.husband_id
                                                        , m.wife_id
     START WITH     parent_id     NOT IN     ( SELECT kid_id
                                           FROM        siblings
     CONNECT BY     s.parent_id     IN ( PRIOR m.husband_id
                            , PRIOR m.wife_id
                            , PRIOR kid_id
SELECT       root_id
FROM       got_tree
GROUP BY root_id
HAVING       MAX (lvl)     <= 2
;This will get a list of parents who may or may not have children, but who do not have either parents or grandchildren.
To get their spouses and children (if any) you will have to join this result set to all the other tables. At that point, you can eliminate poeple who do not have ancestors themselves, but are married to people who have more than one generation of ancestors.
The details of how to do that depend on the details of your tables. If you'd like help, then post a little sample data (CREATE TABLE and INSERT statements for all tables) and the results you want from that data.
Edited by: Frank Kulash on Oct 14, 2009 4:05 PM
I'd need sample data in order to test this, of course.

How to connect many devices with only one FW800 port in iMac?

Hi,
I am upgrading to a new Intel iMac from a 2004 vintage Dual2.0GHz PowerMac. I currently have 8x d2 Quadra drives chained by FW800, and 2x Iomega drives connected vis FW400 hub which also connects HD cams.
My questions is that with only one FW800 port in iMac, I think my devices connectivity is the following?
(1) Get a FW 800 hub (I can only find 2 port ones at the Apple store and BestBuy)
(2) Connect the d2 Quadras to one port of the FW800 hub
(3) Get a FW 800 to FW 400 cable
(4) Connect my 6 port FW400 hub to the 2nd port of the FW800 hub
Thanks for reviewing this solution, and I would also appreciate other suggestions or hear about your experiences if you have a similar set-up.
Will

In addition to your listed considerations, you should consider the following.
Many storage needs do not required FireWire 800 speed. For example, USB 2.0 works fine for your Time Machine backup drive. If you are just storing user data such as your iPhoto or iTunes media files, USB 2.0 is more than fast enough. So, as much as possible, if any of those external drives have USB 2.0 connections and the data storage does not need FireWire 800 speed, offload as much as possible to USB 2.0. I used to be a +FireWire snob+, but since getting an Intel iMac, I find that USB 2.0 works quite well for most data storage purposes.
There are new hard drives that are power efficient and as large as 2TB. Consolidate your data storage needs onto a smaller number of very large drives, partitioned as needed. This will make your setup more reliable (smaller number drives), and save reduce power consumption. If any of your current externals are SATA, you can probably replace the existing drive with an extra large one.
So, I think you setup should be, extra large FireWire 800 drive connected to the FireWire 800 port directly. Using a 9-pin to 6-pin cable, connect the FireWire 400 hub. Connect any non-storage FireWire 400 devices there. Do some data transfer testing to make sure having the 400 hub there on the chain does not cause the 800 connection to slow down.
Connect other drives as needed using USB 2.0, existing or new. Retire the smaller of your external drives.

How do I create a graph with two different y-axis variables with the same x-axis (therefor having two curves)?, How do I create a graph with two different y-axis variables with the same x-axis (therefor having two curves)?

How do I create a graph with two different y-axis variables with the same x-axis (therefor having two curves)?, How do I create a graph with two different y-axis variables with the same x-axis (therefor having two curves)?

Hi Libby,
Select all three columns of data. All three must be 'regular' columns, not Header columns, and the X values must be in the leftmost column.
Click the Charts button and choose the Scatter chart.
The resulting chart will initially show only the first and second columns of data, and the selection will have been reduced to show this.
Click the gear icon at the top left of the selection and choose Share X Values.
You should see a result similar to this:
Notes:
The values on my sample table contain a random element, so they have changed from thhe first image to the second.
The chart is as created by Numbers, with two edits:
Data points have been connected with curves, using the Chart nspector.
The curves were selected and their stroke increased to 2pts, using the stroke formating button in the format bar.
Regards,
Barry

Why won't my iMessage work with only one contact in my phone all my other iMessages send and they just got an iphone but all their iMessages are sending also. I've tried restarting my phone, deleting messages, contact, restarting network

Why won't my iMessage work with only one contact in my phone all my other iMessages send and they just got an iphone but all their iMessages are sending also. I've tried restarting my phone, deleting messages, contact, restarting network

Hello Jesslb23,
Thanks for using Apple Support Communities.
For more information on this, take a look at:
iOS: Troubleshooting Messages
http://support.apple.com/kb/ts2755
To resolve issues with sending and receiving iMessages, follow these steps first
Check iMessage system status for current service issues.
Go to Settings > Messages > Send & Receive and make sure that you have registered iMessage with your phone number or Apple ID and that you have selected iMessage for use. Learn more about troubleshooting iMessage registration if the phone number or Apple ID isn't available for use.
Open Safari and navigate to www.apple.com to verify data connectivity. Learn more about troubleshootingcellular data or a Wi-Fi connection if a data connection isn't available.
iMessage over cellular data might not be available while on a call. Only 3G and faster GSM networks support simultaneous data and voice calls. Learn more about which network your phone supports. Go to Settings > Wi-Fi and turn Wi-Fi on to use iMessage while on a call if your network doesn't support simultaneous data and voice calls.
Restart your device.
Tap Settings > General > Reset > Reset Network Settings on your iPhone.
If you are still unable to send or receive an iMessage, follow these steps
Make sure that the contact trying to message you isn't blocked in Settings > Messages > Blocked.
Verify that the contact you are attempting to send a message to is registered with iMessage.
If the issue occurs with a specific contact or contacts, back up or forward important messages and delete your current messaging threads with the contact. Create a new message to the contact and try again.
If the issue occurs with a specific contact or contacts, delete and re-create the contact in the Contacts application. Create a new message to the newly created contact and try again.
Back up and restore your device as new.
Best of luck,
Mario

Create a Graph with only one set of data? Threw serial

Similar Messages

Maybe you are looking for