Creating a Customized Pad in Ultiboard

I am trying to create a Customized Pad with a Specific size in Ultiboard so that I can make use of it for my PCB Design. I tried to customized a Chip Pad from the Master Database in Ultiboard, but am not successful.
I would appreciate if anyone could give me the steps or guidelines on how I can achieve creating a Pad of specific dimensions or sizes.
Regards.

Hi there,
If you want to edit an exist Chip Pad in the Master Database, you should copy it to the User Database first.( right click the item, and then select User Database)
The following tutorial might be helpful to create a custom component in Ultiboard.
Creating a Custom Component in NI Ultiboard
http://www.ni.com/white-paper/5631/en/
Hope this helps!:-)
Regards,
Chen_T
National Instruments

Similar Messages

Create Footprint with custom pad has solder mask issue

Ultiboard 12 (12.0.653)
When I create a new footprint with normal pads, everything works fine. When I add a custom pad to the footprint or make the footprint with all custom pads, the solder mask does not work correctly.
The attached photo of the Footprint edit mode pad 1.jpg shows 16 standard pads along with three custom pads. The solder mask layer is turned on along with the Copper top layer. All pins should be the same light color. The custom pads are purple. (When you first create the footprint they are green instead of purple).
When a part is placed on the board there is a solder mask shown for all pins like pad2.jpg. If you turn off the solder mask layer the normal pins appear green but the custom pins disappear as shown in pad 3.jpg.
To get around this problem I edited the part in the data base by turning off the soldermask check box for each custom pad pin, then manually created a mask on the solder mask layer for each custom pin.
These custom pads are new pads just created and old custom pads known to work in previous ultiboard versions.
I didn't see any similar messages in the forum. Is this a known issue?
Michael
Attachments:
Pad 1.jpg ‏53 KB
pad 2.jpg ‏39 KB
Pad 3.jpg ‏44 KB

Hi Michael,
I was able to replicate this problem, Ultiboard doesn't want to place solder mask on the bottom layer and on top solder mask, and you have to play around with the pad settings to turn on the solder mask. I will let the developers know about this problem. To work around this issue, you can do following:
1. Make the solder top or bottom the active layer in the Design Toolbox and then select Place>>Graphics, manually draw the soldermask over your custom pad.
2. If your custom pad is an odd shape and you don't want to redraw it, you can create a component with only one custom pad. Save the component and then place the component on the work area by itself. Next select File>>Export>>DXF, export just the copper top layer. Now, create your component and before exiting Footprint Edit mode, select File>>Import>>DXF, merge the DXF you generated to the solder mask top and bottom. When you imported the DXF file, there may be several independent objects and you can’t move them together. In this case, create a window around the DXF data you just imported and then select Edit>>Group Selection to group the DXF data as one object now you can move everything at the same time.
Tien P.
National Instruments

Steps to create a custom UI control in mobile 7.1 ?

Hello Arvind ,
What exactly you mean by signature pad here?
I understood that you want many custom controls in your view.
For this , to start off , you need to create one custom control dc first.
And then you can re use the same for any number of custom controls in the view.
Steps will be :
1) Take a fresh IDE with new workspace
2) Create a new DC (for custom control) of type JAVA .The lik which you gave also speaks about this only
3) Create an application component , bind it with custom control dc.
4) Create a ui component and go ahead with your design of view. Rest all will be the same as simple oca application creation.
For elobarate steps on step-2 (custom control DC creation ), there is a very good document with screen shots which explains everything in detail.
I am not sure if the document is released, will just check that out and provide you the link.
Regards,
Lakshmi
Edited by: Lakshmi Reddi on May 25, 2009 12:22 PM

Vidyadhar,
                 I have created a custom control DC and added added as dependency to a Application component("testapp").Created a new UI component("test_ui) and added "testapp" as depedency in Dev. Infra. view. when i add the "testapp" as depedency to "test_ui" MCD file(<dependency><dependency_name>testapp</dependency_name><dependency_version>1.0</dependency_version></dependency>) , build fails(COMPONENT NOT FOUND) with the following error:(from build.log)
Dependencies in mcd.xml:
          MCD name: testapp MCD version: 1.0
Comparing data in MCD and DPI files.
Error: com.sap.tc.mobile.dt.oca.bp.exception.OCABuildPluginException: Validation of MCD file failed. Component 'testapp' version '1.0' not found. Please check version of used components.
     at com.sap.tc.mobile.dt.oca.bp.impl.cfs.provider.MCDDescription.checkDependencies(MCDDescription.java:139)
     at com.sap.tc.mobile.dt.oca.bp.impl.cfs.provider.CFSDataContextProvider.checkMCDDependencies(CFSDataContextProvider.java:156)
     at com.sap.tc.mobile.dt.oca.bp.impl.cfs.provider.CFSDataContextProvider.execute(CFSDataContextProvider.java:126)
     at com.sap.tc.buildplugin.PrepareContextBuildStep.prepareTechnologySpecificData(PrepareContextBuildStep.java:186)
                at org.eclipse.core.internal.resources.Workspace.run(Workspace.java:1779)
     at com.sap.ide.dii05.util.internal.job.InternalJdiJob$3.run(InternalJdiJob.java:233)
     at com.sap.ide.dii05.util.internal.job.BusyBackgroundIndicator.showWhile(BusyBackgroundIndicator.java:74)
     at com.sap.ide.dii05.util.internal.job.InternalJdiJob.internalRun(InternalJdiJob.java:214)
     at com.sap.ide.dii05.util.internal.job.InternalDiiJob.run(InternalDiiJob.java:275)
     at org.eclipse.core.internal.jobs.Worker.run(Worker.java:55)
Error: Build stopped due to an error: Validation of MCD file failed. Component 'testapp' version '1.0' not found. Please check version of used components.
Error: Build stopped due to an error: Validation of MCD file failed. Component 'testapp' version '1.0' not found. Please check version of used components.
Also, when i add "interactive form" to the view, the properties bounded to interactive form control are for configuring adobe forms. Can i ignore those properties which are not related to my custom control , for which i'll be setting the properties in the code?
Thanks & Regards,
Arvind

How to Create the Custom print Quote Report ?

Hi All,
I want to create the custom Print Quote report . I know the below details and referred the below metalinks .
Note: 780722.1 - How to Create a Custom Print Quote Template in Oracle Quoting ?
https://metalink2.oracle.com/metalink/plsql/ml2_documents.showDocument?p_database_id=NOT&p_id=780722.1
Note: 392728.1 - How to Modify the data source for the XML version of the Print Quote report
https://metalink2.oracle.com/metalink/plsql/ml2_documents.showDocument?p_database_id=NOT&p_id=392728.1
Note: 468982.1 - How To Customize The Asoprint.Xsl
https://metalink2.oracle.com/metalink/plsql/ml2_documents.showDocument?p_database_id=NOT&p_id=468982.1.
Oracle Metalink:
Note: To add a column to the print quote report, following files need to be updated:
LinesVO.xml --- xml files containing the sql query and attribute definition
LinesVORowImpl.class - public class extending the framework class OAViewRowImpl.
This class contains the set and get for the attributes defined in xml file.
ASOPRINT.xsl - this is the xsl stylesheet file used to describe the report layout.
This file needs to be modified to include the new column being added to the report
QUESTION :
My question is,
1. wether my approach (below iare the details)of trying to extend the PromptVO is the right way or is there any other way to add the new columns.
I want to add new fields on to the report . When i looked into the it says the below
Here we find that to add a new column, oracle says to update the LINESVO.xml, do they really mean to update the base files.
This report uses following VO's
PROMPTVO
HEADERVO,
LINESVO.
To create new Headers & Prompts, i tried extending the PROMPTVO. Once the extended VO is substitued , i dont even get the data for standard oracle Prompts. is this the right way to add columns?
Thanks

Hi All,
I want to create the custom Print Quote report . I know the below details and referred the below metalinks .
Note: 780722.1 - How to Create a Custom Print Quote Template in Oracle Quoting ?
https://metalink2.oracle.com/metalink/plsql/ml2_documents.showDocument?p_database_id=NOT&p_id=780722.1
Note: 392728.1 - How to Modify the data source for the XML version of the Print Quote report
https://metalink2.oracle.com/metalink/plsql/ml2_documents.showDocument?p_database_id=NOT&p_id=392728.1
Note: 468982.1 - How To Customize The Asoprint.Xsl
https://metalink2.oracle.com/metalink/plsql/ml2_documents.showDocument?p_database_id=NOT&p_id=468982.1.
Oracle Metalink:
Note: To add a column to the print quote report, following files need to be updated:
LinesVO.xml --- xml files containing the sql query and attribute definition
LinesVORowImpl.class - public class extending the framework class OAViewRowImpl.
This class contains the set and get for the attributes defined in xml file.
ASOPRINT.xsl - this is the xsl stylesheet file used to describe the report layout.
This file needs to be modified to include the new column being added to the report
QUESTION :
My question is,
1. wether my approach (below iare the details)of trying to extend the PromptVO is the right way or is there any other way to add the new columns.
I want to add new fields on to the report . When i looked into the it says the below
Here we find that to add a new column, oracle says to update the LINESVO.xml, do they really mean to update the base files.
This report uses following VO's
PROMPTVO
HEADERVO,
LINESVO.
To create new Headers & Prompts, i tried extending the PROMPTVO. Once the extended VO is substitued , i dont even get the data for standard oracle Prompts. is this the right way to add columns?
Thanks

Is there a way to create a custom screensaver with pics/slides that display for different amounts of time?

Is there a way to create a custom screensaver with pics/slides that display for different amounts of time? Or even add a "video slide" into the screensaver?
My business has 3 TVs displayed in our lobby, each with its own apple TV and they are all linked to the same photo stream. Currently the Atv screensaver displays the photostream pictures of our products for the default 3 seconds. We just added pics/slides that now display messages and useful info for our customers but I want that info to be displayed for a longer period of time than the pictures to give people a chance to read it.
I tried using flickr and powerpoint as a work around but no luck. I created a slide in powerpoint with play length of 15 secs and saved it as a wmv file. I added that file to a "screensaver" set in flickr and pointed the Atv screensaver to that flickr set. It still displays everything, pics and the wmv file at the default 3 sec.
I know I can increase the duration of all pics in the screensaver to display for longer but the goal is to have the pics display at 3 secs and the info slides to display at 15 secs.

Welcome to the Apple Community.
No that's not possible.
If you have any suggestions that you think might enhance the Apple TV you can send Apple your feedback here

I am changing from Word to Pages. I have created my custom template with all my styles etc and that is what comes up when I go for a New Document. Fine. How do I get it to use the same Custom Template when I use Pages to open a Word document?

I am changing from Word to Pages. I have created my custom template with all my styles etc and that is what comes up when I go for a New Document. Fine. How do I get it to use the same Custom Template when I use Pages to open a Word document?

The template is a document in itself, it is not applied to an existing document whether it is a Pages document or a Word document converted to a Pages document.
You would need to either copy and paste content, using existing styles, or apply the styles to the converted Word document.
You can Import the Styles from an existing document and those imported Styles can be used to override the current document's styles:
Menu > Format > Import Styles
The process is simplified if the styles use the same names, otherwise you will need to delete the style you don't want and replace it with the one that you do want when asked, then the substitution is pretty straightforward.
Peter

Create a custom web template using VS 2012 with web features,site features sections applied

hi,
Want to create a custom web template using VS 2012 in my SP 2013 environment. i know "Vesku" has posted a great artice on this [ based on prev. version of SP].
here -
http://blogs.msdn.com/b/vesku/archive/2010/10/14/sharepoint-2010-and-web-templates.aspx
i am looking for a code based article which has step by step process which provides how to add the site features, web features and attach the eventreceivers etc etc on sitecollection creation when i apply this template from central admin.
can anyone provide me any links / any source how to create a custom web template with one / two custom features - site features element and web features element , / master page etc ....
I am stuck with this. as part of my reqmnt, i need to create a webtemplate with all the customlistinstances, custompagelayouts, custom masterpages, custom appln pages, custom web parts.
help is appreciated !
Das

The problem is that Web Templates are deployed to a gallery in a site collection and aren't available in Central Admin when creating a new site collection. YOu have to create the site collection without choosing a template and then choose your web
template when you first access the root site in the site collection. Here's an article that discusses that process here:
http://sharepointchick.com/archive/2011/02/10/using-web-templates-to-create-site-collections.aspx
Other than that Vesa's article is still the best one and works essentially the same in 2013 as it does in 2010.
Paul Stork SharePoint Server MVP
Principal Architect: Blue Chip Consulting Group
Blog: http://dontpapanic.com/blog
Twitter: Follow @pstork
Please remember to mark your question as "answered" if this solves your problem.

Create a custom Master Page in SharePoint Foundation 2013

Hi,
I am new to SharePoint foundation.
I am trying to create a custom master page and save it as template, so that i can use it for all other sub sites. But i don't know where to start. Also i tries searching in Google, i got results for share point and not for share point foundation.
So, Please give me a step by step procedure or a link to step by step procedure on how to create a master page, save it as template and use it for a sub site.
Thanks in advance,
Gowtham R

Few points to note related to SharePoint Master page:
You don't need to create master page template. If you deploy your master page in site collection level you can reuse the same master page in subsites without copying again and again, rather just by referencing
You have not mentioned how you are going to deploy your master page. If you have any Visual Studio (VS) solution already, try to add your master page in the VS solution and deploy your master page (and other branding components) as SharePoint WSP
solution.
Deploying master page will not activate the master page, you need to use some kind of 'Web Level Feature' to activate your branding - the feature will basically set the master page property of SharePoint site to your custom master page.
Please follow the links below for steps by steps instructions (and you will find many just by googling 'sharepoint master page visual studio'):
http://frederik.se/how-to-deploy-a-custom-master-page-in-sharepoint-2013-using-visual-studio/
http://joshuaorimogunje.wordpress.com/2011/10/05/how-to-create-custom-master-page-for-sharepoint-2010-using-visual-studio-2010/
http://blogs.msdn.com/b/bobgerman/archive/2011/01/31/packaging-master-pages-and-page-layouts-with-visual-studio-2010.aspx
http://go.limeleap.com/community/bid/291931/Creating-a-Custom-SharePoint-Master-Page-with-jQuery-Using-Visual-Studio
Thanks,
Sohel Rana
http://ranaictiu-technicalblog.blogspot.com

How to create a custom function module with the records in SAP R/3?

Hi All,
How to create a custom function module with the records in SAP R/3? Using RFC Adapter I have to fetch the custom function module records.
Regards
Sara

Hi
goto se37...here u need to create a function group... then u need to create a function module. inside assign import/export parameters. assign tables/exceptions. activate the same. now write ur code within the function module
http://help.sap.com/saphelp_nw04/helpdata/en/9f/db98fc35c111d1829f0000e829fbfe/content.htm
Look at the below SAP HELP links, These links will show you the way to create a Function Module
http://help.sap.com/saphelp_nw04/helpdata/en/26/64f623fa8911d386e70000e82011b8/content.htm
http://help.sap.com/saphelp_nw04/helpdata/en/9f/db98fc35c111d1829f0000e829fbfe/content.htm

How to create a custom layout set to display the KM folders...

Could someone please tell me how to create a custom layout set to display the KM folders?
Thanks,
Sudha.

Hi Sudha,
Please check the following blogs whick will guide you step by step.
https://www.sdn.sap.com/irj/sdn/weblogs?blog=/pub/wlg/4123
https://www.sdn.sap.com/irj/sdn/weblogs?blog=/pub/wlg/3071
http://help.sap.com/saphelp_nw2004s/helpdata/en/c3/c91b5610b65b4aa8204d09384d156b/frameset.htm
If helps reward points
cheers
dev

How to create a custom task in SRM for the standard task

Hi Gurus,
How to create a custom task in SRM for the standard task eg: TS10407929
regards,
George.

from PFTC itself. Same.

How to create a custom panel in the right way (without having an empty panel in the file info) ?

Hi Everyone
My name is Daté.
I'm working in the fashion industry as a designer and Design consultant to help fashion brands improving the design workflow by using Adobe softwares and especially Illustrator.
I'm not a developper, but i'm very interested about the possibility to introduce xmp technology to provide more DAM workflows in the fashion industry.
Fashion designers produce a lot of graphical objects in illustrator or Photoshop. Unfortunately they are faced to a big challenge which is about how to manage, search, classify and get this files faster. Of course PDM system or PLM system are used in the Fashion industry to manage data, but for many companies, implemanting this kind of database is very complex.
When i look at what you can do with xmp, it seems to be an interesting way of managing design files, then i started to follow Adobe instruction to try to build a custom panel.
The main idea is to (Theory) :
create custom panels used by fashion designers to classify their design files.
Use Adobe Bridge to search files, create smart collection to make basic reports in pdf and slideshows
Find someone to make a script able to export metadata in xml files
Use indesign and the xml file to generate automatically catalogues or technical sheets based on xmp values
I have created a custom panel by using the generic panel provided by Adobe and i have modified the fields to feet with the terms used in the fashion industry and it works well.
But unfortunately, when i try to create my own custom panel from scratch with Flashbuilder (4.6) and the Adobe CSExtensionBuilder_2 (Trial version), it doesn't work!
Here is the process :
I have installed flashbuilder 4.6
I have download the XMP Fileinfo SDK 5.1 and placed the com.adobe.xmp.sdk.fileinfo_fb4_1.1.0.jar in C:\Program Files (x86)\Adobe\Adobe Flash Builder 4.6\eclipse\plugins
In Flashbuilder, i have created a new project and select xmp Custom panel
The new project is created in flashbuilder with a field with A BASIC Description Field
To generate the panel, right click the project folder and select xmp / Publish Custom Panel
The panel is automatically generated in the following folder : C:\Users\AppData\Roaming\Adobe\XMP\custom file info panels\3.0\panels
Go to illustrator, Open the file Info
The panel appears empty
The others panel are also empty
The panel is created and automatically placed in the right folder, but when you open it in Illustrator by selecting the File Info option in the File Menu, this custom panel appears empty!!! (only the title of the tab is displayed). This panel also prevent the other panels to be displayed.
When you delete this custom panels from the folder C:\Users\AppData\Roaming\Adobe\XMP\custom file info panels\3.0\panels and go back to the File Info, the other panels display their content properly.
I also try to use the plugin XMP Namespace designer to create my own namespace. this plugin is also able to generate a custom panel, but this one also appears empty in AI or Photoshop.
I try to follow the process described in Adobe xmp documentation many times, but it didn't works.
It seems that many peaople have this issue, but i dodn't find a solution in the forum.
I try to create a trust file (cfg), but it didn't work.
It would be so kind if you can help me to understand why i can't create a custom panel normally and how to do it in the right way.
Thanks a lot for your help,
Best regards,
Daté

Hi Sunil,
After many trial, i realize the problem was not coming from the trust file, but from the way i have created the custom panel.
There is 2 different ways, the first described below is not working whereas the second is fine :
METHOD 1 :
I have downloaded the XMP-Fileinfo-SDK-CS6
In the XMP-Fileinfo-SDK-CS6 folder, i copied the com.adobe.xmp.sdk.fileinfo_fb4x_1.2.0.jar plugin from the Tools folder and i pasted it in the plugind folder of Flashbuilder 4.6
The plugin install an XMP project
In Flashbuilder 4.6 i have created a new project (File / New /Project /XMP/XMP Custom Panel)
A new xmp project is created in flashbuilder.
You can publish this project by right clicking the root folder and selecting XMP / Publish Custom Panel
The custom file info panel is automatically published in the right location which is on Mac : /Users/UserName/Library/Application Support/Adobe/XMP/Custom File Info Panels/3.0 or /Users/UserName/Library/Application Support/Adobe/XMP/Custom File Info Panels/4.0
Despite the publication of the custom file info panel and the creation of a trust file in the following location : "/Library/Application Support/Macromedia/FlashPlayerTrust", the panel is blank in Illustrator.
I try this way several times, with no good results.
METHOD 2 :
I have installed Adobe CSExtensionBuilder 2.1 in Flash Builder
In FlashBuilder i have created a new project (File / New /Project /Adobe Creative Suite Extension Builder/XMP Fileinfo Panel Project)
As the system display a warning about the version of the sdk to use to create correctly a custom file info, I changed the sdk to sdk3.5A
The warning message is : "XMP FileInfo Panel Projects must be built with Flex 3.3, 3.4 or 3.5 SDK. Building with Flex 4.6.0 SDK may result in runtime errors"
When i publish this File info panel project (right click the root folder and select Run as / Adobe illustrator), the panel is published correctly.
The last step is to create the trust file to display the fields in the panel and everything is working fine in Illustrator.
The second method seems to be the right way.
For sure something is missing in the first method, and i don't understand the difference between the XMP Custom Panel Project and the XMP Fileinfo Panel Project. Maybe you can explain it to me.
So what is the best solution ? the right sdk to use acording to the creative suite (the system asks to use 3.3 or 3.5 sdk for custom panels, so why ?)
I'm agree with Pedro, a step by step tutorial about this will help a lot of peaople, because it's not so easy to understand!!!
Sunil, as you belong to the staff team, can you tell me if there is :
A plugin or a software capable to extract the XMP from llustrator files to generate XML workflows in Indesign to create catalogues
A plugin to allow indesign to get custom XMP in live caption
A plugin to allow Bridge to get custom XMP in the Outputmode to make pdf or web galeries from a smart collection
How can you print the XMP data with the thumbnail of the file ?
Thanks a lot for your reply.
Best Regards
Daté

How to create a custom table in the below format

Dear Friends
can any one please let me know hot to create a custom table as below
outpatient
|employeeno | class | startdate | enddate | spouse |1stchild | 2nchild| Rate | amount|
My FO wants to enter in the SM30 as above ......i.e he wants to have spouse ,1st child and 2nd child under one group........so he asking me to make as one group
and give a heading as outpatient.........similary i have to give for in patient.
Please could any one tell is it possible.
regards
syamala...

Under the SAP forums section, there is ABAP development and in That there is ABAP General.
SAP forums > ABAP development > ABAP General.
Post in that forum.
Regards
AK
Please reward if helpful

How to create a Custom List without the column "Title" ?

Maybe this one is easy as it sounds, I just want to know how to create a little list for my SharePoint application featuring 3 columns:
1 - User Name (this should be Person type - UNIQUE + Required)
2 - Report (Memo - Required)
3 - Status (Choice + Required)
The list will be used to allow the users to submit a weekly report and I don't want to include the title because there is no use to me, I know I can hide the column by customizing the list but this sounds very amateur even for a newbie like me (yeah... sounds
so cheap!), since I've been reading a lot about custom content types and I still didn't get the chance to use this properly I was wondering how I could put them to use and I guess the example here would be the best right?
I really spent some time trying but I always end getting the Title even when I try to use custom content types so I'm really giving up and asking for some help at this point.
Thanks a lot for the help!!!

Yes, you can do that. If you need a different content type with your custom fields. Following are the steps : http://www.dotnetcurry.com/ShowArticle.aspx?ID=620
After creating your custom Content Type, Click on the 'Title' filed in your custom content type.
In the 'Column Settings' make it 'Hidden (Will not appear in forms)' and click ok.
Now add this content type to your list/library.
In the list/Library go to setting and 'Advance settings' and make the 'Allow management of Content Type?' as 'yes' and click ok.
Now make default content type not visible from 'Change new button order and default content type' link in the settings page of list/library, and your contet type as 'Default'.
Create a new view, remove the 'Title' field and make that view as 'dafault' view, you can delete the 'All Items' view also if required.
Now whenever user come to that list/Library they will not see the title column and also will not appear in the 'New Item'.
Note : The 'Title' field is mandatory in all the list/library and by default added to the 'All Item' view. So, by doing above steps you are creating a new content type where 'Title' is not mandatory and also not added in default view.
get2pallav
Please click "Propose As Answer" if this post solves your problem or "Vote As Helpful" if this post has been useful to you.

How to create new Custom XML Report without using Form Builder

Hi,
What are the steps to create new Custom XML Report without using Report Builder ?
Thanks and Regards,
Abhi

Hi,
Steps we now follow
1)Create Data Model in Reports Builder
2)Create xml
3)Insert xml in Publisher to build Fomat
4)FTp rdf
5)Create Data Definition and Template
6)Create executable and Concurrent Program
Is there any way we can build reports without use of Report Builder ? By writing PL SQL Package for Before Report and After Report etc ...
Thanks and Regards,
Abhijit Rode

Creating a Customized Pad in Ultiboard

Similar Messages

Maybe you are looking for