Decklink stopped putting out a signal

Or HDTV stopped receiving.  I was not using Decklink for a month or more.  During that time I installed an esata card.  Could that have caused a problem?
Frustrated.

First off, I'd try reseating the card.  Seems to me that there were some issues as to which slots certain cards were installed in.  Can you try moving the cards around?  You might also make sure you've got the latest drivers from decklink.  Does system profiler see the decklink card?

Similar Messages

  • Why did my 5G Classic stop putting out audio to peripheral ipod connectors?

    My 5th Gen 80Gb iPod Classic was working superbly until this past April.  I used it in a Sony iPod Dock and my new Tundra using the USB connection religiously for the past two years.  It worked fine without any issues until one day in mid-song, the sound went out while playing in the Sony.  The iPod was still playing, but no sound was being output to the Sony dock.  (This did happen on a beach in 80 direct degree sunlight onto the Sony unit, but the dock is covered by a door and little sunlight would get to the iPod).  I then returned it to my Tundra audio via USB and it did not wake up automatically and get recognized by the audio system as it did before.  I had to press the wheel button to get the Tundra's audio system to recognize it, but then it played (and still plays) fine thru USB.  I since purchased an iOn Block Rocker, with an iPod dock that I have tested with an iPhone, and it works perfectly.  I plugged my iPod Classic into the same jack and it will not output any sound to the iOn either., not even thru the RCA jack via the earphone connection.  I tested the RCA with my Infuse 4G Phone and IT worked perfectly as well.  I think there may have been some event with the accessory interface pin(s) on the iPod (if such a thing exists) or maybe one of the chips that processes the accessory signals got hosed
    Anybody here have an idea what causes this behavior and how to fix it.  I have reset my iPOD to factory defaults a few times and have updated it to the latest software version thru iTunes.  Any knowledge or assistance would be greatly appreciated.

    If the reset does not work try the remaining items of:
    - iOS: Not responding or does not turn on
    - Also try DFU mode after try recovery mode
    How to put iPod touch / iPhone into DFU mode « Karthik's scribblings
    - If not successful and you can't fully turn the iOS device fully off, let the battery fully drain. After charging for an least an hour try the above again.
    - Try another cable       
    - Try on another computer                            
    - If still not successful that usually indicates a hardware problem and an appointment at the Genius Bar of an Apple store is in order.
      Apple Retail Store - Genius Bar                              

  • A periodic fast signal to put out randomly to two different lines

    thank you so patient to answer me so fragmentary question.
    What I want is a two random fast digital output.However,two of outputs is related. superpose them will produce a periodic fast singal.In other words,when the line 1 put out "1",the line 2 put out "0".But when to put out "1" or "0" is random.
    I have studied 6602 manual and the examples in Help menu.But I can not find way to do that.In DIO context,the digital I/O is static(In my view,it can not put out fast signal.What is the max frequency o f it?);and in counter context,pulse generation only put out a periodic signal.So I don't know how to do it.

    I am a little confused with your question. On the NI-6602, you are correct in stating the digital lines are static (writing/reading to digital lines is controlled by software). Therefore, the speed of writing/reading to/from the digital lines will by system dependent.
    It seems to me as if you want two pulse trains to start at the same time but be inverted. You could program the counters to share a start trigger and have one counter start at a digital low and the other counter to start at a digital high. This would produce two pulse trains that would be synchronized and inverted. I hope this helps.
    Todd
    Applications Engineer
    National Instruments

  • Buffered analog output puts out additional sample on aborting or stopping task

    I'm using DAQmx and LV 8.2
    I'm doing a buffered analog output operation where the sample clock is driven by pulses from ctr0 on the same device (PXI-6070E).  When I end the analog output task, either with the DAQmx stop task or DAQmx control task (abort option selected), the AO puts out one additional point from the buffer.  (I have checked by setting breakpoints and stepping through the code that the additional point is definitely generated when the analog ouput task is aborted)
    I need the output to remain where it was before the stop task command is issued.  How do I fix this?
    Thanks,
    Marc

    I'm watching to see if there hasn't been a sample output in a certain length of time, then terminating the task if there hasn't been.  Specifically, I have ctr0 outputting pulses to drive the task based on input from the AnalogComparisonEvent terminal.  I'm using a counter on a different PXI device to count the number of pulses and monitoring this count to determine if another sample has been output.  I'm outputting the ctr0 pulse to PFI3 as well, and I'm monitoring both the ctr0 output (which drives the ao clock) and the analog output itself on an oscilloscope.
    Basically I'm sitting in a while loop waiting for the monitoring counter to fail to increment.  Then I terminate the while loop and stop the analog output task.  I can watch the analog output on the oscilloscope while I step through the program.  Immediately before the daqmx control task - abort (or daqmx stop if I don't abort first, or daqmx clear, if I don't abort or stop) vi runs, the analog output remains outputting the last sample.  Immediately after the abort, stop, or clear, the analog output advances one sample in the buffer. 
    During this time, ctr0 does not output another pulse, so the scan clock should not advance.
    Thanks,
    Marc

  • NI Stepper Motor not putting out enough torque

    So I have a motion control system with a P70360, UMI 7772, PXI 7332, and a NEMA 23 stepper motor with 380 oz-in. The purpose of the set up is to rotate horizontally a testing fixture and hold it in position (slowly). Previously the set up was using a motor with 180 oz-in but it was decided that it wasn't enough torque seeing as it wasn't able to fully rotate the fixture, also using a step resolution of 18000, current reduction is disabled, multistepping is enabled, dynamic smoothing is minimal, and load-inertia ratio is set to 0-1.
    When the 380oz-in motor was plugged in it was still unable to rotate the platform completely but it wasn't even able to rotate it as far as the 180 oz-in which leads me to believe it was outputting less torque than it should have been. The only reasoning I could think of for this was that there was an issue with the settings somehow where it was limiting the power being fed into the motor for whatever reason. So I walked through the manual (http://www.ni.com/pdf/manuals/372324d.pdf) and it still wasn't giving enough torque.
    I also read that decreasing the step size would increase the torque so I reduced it to 200 and it started making a grinding noise, which made everyone in the lab stare at me and start laughing... I immediately hit the kill motor button (I've been controlling it using NI MAX).
    So far I can't seem to find anything that mentions the motor making a grinding noise or not pulling enough torque while using the P70360 so here I am asking the community. Why is the motor making the grinding noise (which also seems to become less the higher the step resolution is) and why isn't the motor putting out more torque?
    Also of note, I'm an electrical engineer, meaning my understanding of mechanical terms is limited to the basics.
    Thanks for any help you can give.
    DISCLAIMER: I'm a hardware engineer so I may not be familiar with some concepts/terminology/best practices so... patience is appreciated

    I can't get too specific about the dimensions but it's a rectangular platform about 8 inches wide and 25 inches long (axis of rotation goes through the long way). There are also the UUT seating on one side which is what's causing the imbalance but by placing my lab notebook on the other side it balances out. I would estimate my book to weigh around 2 pounds.
    The exact weight I'm not sure, the platform is attached to two stands through some type of bearings and the motor is turning a part of the shaft that is sticking out slightly.
    On another note though, I decided to attach a oscilloscope to the motor to verify the signals were correct. I had made all the connections, double checked them to make sure all my connections were correct and weren't shorting then turned on the power. As soon as I did there was a white flash from the driver, I turned off the power, and I could smell something was burning. I took the lid off but couldn't see any immediate burn marks anywhere nor was there any visible smoke, just the odor. I decided not to try it again and my principal engineer has been trying to convince me to use another companies motion system. So sadly this may be the last well funded venture into NI motion control I take.
    I'm still going to try to get in touch with a rep and see what I can do about it including taking into consideration the possibility of a gearbox but it's going to have to be on my spare time :'(
    DISCLAIMER: I'm a hardware engineer so I may not be familiar with some concepts/terminology/best practices so... patience is appreciated

  • My 4-year old AirPort Extreme intermittently drops out (no signal to my iMac Book).  The laptop shows reception of other nearby Wi-Fi transmitters, but not mine.  I have changed the bands, but the problem comes back.  Transmitter problem or interference?

    My 4-year old AirPort Extreme intermittently drops out (no signal to my iMac Book).  My hard-wired iMac still has internet capability.  The laptop shows reception of other nearby Wi-Fi transmitters, but not mine.  I have changed the bands back and forth, but the problem comes back.  How can I check if it is a transmitter problem or interference?

    Let me see if I can suggest a strategy.
    I have talked with my ISP and he said that I am not the only one with an Airport Extreme with the same issue. He said to try to write the DNS direclty, rather than using the Auto settings - still nothing works.
    What modem do you have and what sort of broadband?
    What mode is the AE in.. router or bridge?
    I have an Airport Express from 2010. Since about a month and definetly since yesterday, I cannot connect any device via Wifi to it although LAN connection works correctly.
    Is this express or extreme.. the rest of the post you refer to extreme.
    What is the actual model number of the AE? A1xxx from the base or the part number MCxxx from the box.
    If the AE is bridge.. I want you to try a different method.. put it in router mode.. don't worry about double NAT but ensure the IP range of the modem /router is different to the AE.. so if one is 192.168.x.x then the AE on default at 10.x.x.x is fine.. if the main router is 10.x then move the AE to 192.168.x.x
    Make sure the guest wireless is off.
    Using a 5.6 utility on your 10.6.8 OS mini go to the log and see if the wireless is registering..
    You should see lists of wireless connection like..
    Post as many screenshots of the setup as you can.. it helps loads.
    IPv6 is starting to become a pain.. try it off and try local link and try auto.. in the computer.

  • I have and ipod touch 4g, it stop working out of nothing, tried everything..

    i have and ipod touch 4g, it stop working out of nothing, i tried to restore, i plugged in to another computer and to the outlet wall and nothing, didnt drop it or got wet, someone told me that it happens sometimes with this ipod generation. what can i do? i bought it to years ago.

    Try:
    - iOS: Not responding or does not turn on
    - Also try DFU mode after try recovery mode
    How to put iPod touch / iPhone into DFU mode « Karthik's scribblings
    - If not successful and you can't fully turn the iOS device fully off, let the battery fully drain. After charging for an least an hour try the above again.
    - Try on another computer
    - If still not successful that usually indicates a hardware problem and an appointment at the Genius Bar of an Apple store is in order.
    Apple Retail Store - Genius Bar       

  • How do you get multiple live instruments to put out sound?

    I just got a M-Audio 61 keyboard from my wife for our anniversary. I love it and it works great with GarageBand 1.X. I also have a guitar I use with GB. It is plugged in the 1/8 in. mini jack input in the back of the Mac. I however can't get both to put out sound at the same time. Lets say, for instance, that I would play the guitar and my wife the keys. How can I get both to put out sound at the same time?
    Thank for any help you can offer.
    Your friend in Mac OS X,
    Jose

    Danke Christoph!
    I was glad to get your response. I thought I was not doing something right in GarageBand. I'll get GB2 and try out multiple live sources.
    Once again thanks.
    Your friend in Mac OS X,
    Jose Mauricio Cuervo

  • I am using an apple TV to show a slide show which is sent via WiFi from a mini computer.  The slide show repeats for a few hours and then stops and shows "no signal".  What's going on- and how do I get the show to cycle indefinitely?

    I am using an apple TV to show a slide show which is sent via WiFi from a mini computer.  The slide show repeats for a few hours and then stops and shows "no signal".  What's going on… and how do I get the show to cycle indefinitely?  (I have set the server to NEVER sleep)

    Welcome to the Apple Community.
    Have you also set the Apple TV not to sleep.

  • Why does my HP LaserJet 4 Plus put out blank page after print page?

    why does my laser Jet 4 Plus put out a blank sheet after every print page

    This sounds like an issue that could result from having A4 sized paper but having the printer settings set for A size.  Please check the paper settings.
    Bob Headrick,  HP Expert
    I am not an employee of HP, I am a volunteer posting here on my own time.
    If your problem is solved please click the "Accept as Solution" button ------------V
    If my answer was helpful please click the "Thumbs Up" to say "Thank You"--V

  • My iTunes has stopped working out of nowhere. When iTunes is opened it displays "iTunes has stopped working" and windoes automatically closes it saying it will look for a soluton. What do I do? I have un-installed it and re-installed multiple times.

    My itunes has stopped working out of nowhere. When I open iTunes a message appears stating "iTunes has stopped working." and windows closes iTunes sayng it will look for a solution. I have Windows 8.1 64-Bit and have been using iTunes 11.1 (or the newest one out there). I have un-installed and re-installed multiple times. The same message continues to pop up.

    Hi biazonmg,
    Thanks for using Apple Support Communities.  If iTunes is unexpectedly quitting when you open it, this article has steps to isolate and troubleshoot that:
    iTunes for Windows Vista, Windows 7, or Windows 8: Fix unexpected quits or launch issues
    http://support.apple.com/kb/ts1717
    Cheers,
    - Ari

  • Lightroom 3 - The worst program Adobe has ever put out...

    If anyone cares to read this, I will be the first to say DO NOT UPGRADE!!
    I am spreading the word - facebook, word of mouth, every professional photographer in LA I know, blogs, etc. 
    You gotta raise hell to get changes.
    Lets see if Adobe will do anything about these issues...
    I thought that Adobe created "beta" for a reason - to smooth out all the kinks before they put the disk out. Nope. 
    I have been waiting for them to put out updates on many issues since I purchased the disk a month ago.... Still waiting Adobe!!!
    It is excruciating to watch my photos take literally 4-5 minutes to open.  Even worse, is the time it takes to save from Photoshop CS5 back to Lightroom - I timed 14min. FOR A PHOTO!
    I feel like the old days when I rendered video - went out to get a coffee, and came back to find the spinning of wheel of death still spinning.
    Oh, and I got to talk to India today too! for 3.5 hours - with no resolution to my problems. 
    Susheel accessed my computer remotely  - saw my catalog - sees 73,000 images, and asks "are you a photographer?"  REALLY?!  DId you REALLY just ask me that Susheel??
    Why I HATE Lightroom 3 - let me count the ways:
    1. Adobe closed their tech support in Portland (whom I have spoken to many times, and ALWAYS got my problems resolved.  They always went above & beyond the protocol - and we sit here and wonder why the US economy is crashing), now you get a no-name person in India or in the philippines (who have no extension, no email, not even a direct line so when you sit on a call for 3.5 hours and need to call back you are starting all over again.. Dear Adobe - do we live in 1980?? You are suppose to be a LEADER in technology. 
         I am morally against outsourcing, my artwork is all about the death of american industrial capitalism.  In a time when the US is in crisis, Adobe works on moving things out of the US.  I'm outraged - You can't get someone in the US EVEN IF YOU TRIED!  The best I could do was talk to someone in sales about this - wow. What does that say - American's "look good and sound good to sell our product, but when it comes to something advanced in technology like using the product and trouble shooting, we prefer to use someone with no extension in another country"
    2. They don't offer support for anyone who is running off a network (they expect professionals to be working off their local "c" drive or Mac internal hard drive.  HA!! 
    3. They continued to blame my network - even though my network is running smoothly, has no limitations on access, will open directly into photoshop just fine (and quick!), worked absolutely perfectly in Lightroom 2.... Yeah, it's the network, riiight.
    4. Lightroom 3 is corrupting files when opening into Photoshop CS5 - if I'm lucky enough to open them
    5. When I do get a photograph open, it loses it's filters once saved back into Lightroom (I rate my photos to help me navigate through the masses) - this really is hurting my workflow. When I shoot 800 images in the studio in one day - I DO NOT want to go back and fish around to find the edited version that lost its flag...
    6. I have been promised to get a phone call "sometime next week" since there is no extension I can call back on to move forward.  I'll keep you updated - let you know if Susheel keeps his word.  He couldn't tell me who was going to call me, or when, but he "assures" me it will happen.
         I wont hold my breath

    function(){return A.apply(null,[this].concat($A(arguments)))}
    Keith_Reeder wrote:
    ambienttroutmask wrote:
    So the worst programme Adobe ever put out, yet even though you can have a 30 day trial you still went out and brought it...
    Yep, everything is always someone else's fault. It's never because they've made a stupid decision to buy before making absolutely sure that the software will work for them.
    Seems like nobody is prepared to take responsibility for their own actions these days.
    So, by that logic Adobe does not have to take ANY responsibility for pushing this kludge out the door?  Given they had a RC ready almost INSTANTLY after release should be sufficient to show they KNEW they were pushing garbage out the door.  Adobe is indeed responsible for their offering a know buggy product, bugs which CROSS PLATFORMS so it has to be the core code design not the user hardware or anything a given user has done.  Sure some systems might have setups which help make these issues more apparent, but that is on Adobe to deal with as they should publish limitations and known configurations which can potentially induce greater problems...but these entail an admission and accepting responsibility for the original buggy release...btw, release notes used to be where one would find quirks info and how to work around them post system requirements being carved in stone and set to entice the lowest common denomonator user.
    One more thing...LR is marketed not as a PRO TOOL, it is sold as a tool for the average to hobby level photographer.  That is also has huge appeal to the pro market is a happy accidentally-on-purpose thing...but to berate people who don't feel it's their job to troubleshoot a commercial app is completely unreasonable...but anymore the US consumer is the largest beta tester group on the planet...I wonder how our EU counterparts are fairing as ironically, they have stronger consumer protection laws...try pushing a crap product out in the German market...heh-heh, yeah good luck with that.
    Actually I would say this is not the worst software Adobe has ever pushed out the door but perhaps the worst photography software they ever sent as RTM.  Many, many PDF related apps and utils have actually been worse and we won't get into what they have done to Flash and Dreamweaver after that acquisition.  The closest analog I can see if that of what happened to Norton products post Norton being purchased by Symmantec.
    However, I am willing to give Adobe time to address this because they did have the RC ready almost right away.  Should they have done this?  No way, but perhaps the marketing wonks put the company in the position where it had to meet the release date even if issues were discovered and fixes in the pipeline already and it was gonna be a 3-9 week delay before the issues were mostly fixed.  But they did and well, even those who ran the beta, ran the 30-day trial did not find the issues because they simply did not use that part of the program enough for the bugs to manifest their effects to the degree when you the user, realize something odd is happening.
    I too am pissed, beyond belief as I depend on LR for my business, I can, however work around it for a while but I don't make money as a photographer I use photography for my business so the issues, while causing huge levels of frustration, are not fatal....yet...all I know is I don't want to revert to LR2.7 because I have done so much work onLR3/ LR3.2RC already and the tools themselves are indeed superior in LR3.x....when they work and that is the rub.  So many here are telling those with these bugs affecting their income/workflow bought into this to save time and leverage the bestter NR/sharpening and I say much improved adjustment tools.  I don't use the lense profiles at all really so nothing special for me there.
    I would ask a question...I am sure this has been asked and answered but, eh, why not one more time because search is sooooo "haaaard"
    but does this issue affect all file types?  I am shooting DNG but can switch to PEF if needed and convert on import but would rather just shoot DNG.  I am not willing to switch to JPG because if I have to do this I give up too much control on my images, for that I would switch back to LR2.7.
    Also, what versions of Camera RAW were used in the beta and what versions are being used with LR3.  I know I did upgrade to ACR6.2(?) or whatever the most current version.  I understand there are a ton of factors at play in these bugs but I do doubt it's ACR as my old antique PS CS3 version of Photoshop does not have any problems, of course it's using the old version of ACR 4.6(?) again sorry I forget what version exactly but it's trivial and can be determined.
    I like LR because I don't need the advanced features of PS all that often, still PS is a fun tool to have as a backup for the complicated shots though I don't have time to really spend in it as I would like to...
    But in general I guess I am trying to say, Adobe had to know in advance of the RTM original LR3 because they had the RC ready almost instantly.  Of course past releases of LR also had the same experience just the bugs were, well, not as impactful I suppose.  I have been happy with LR since 1.x versions but this version is painful to support...and I as I previously posted I won't screw with Adobe's refund people, likely off-shored staff who get bonuses for talking customers OUT of getting a refund, I will simply file a chargeback with Mastercard...that is why I use it, so I don't have to let companies waste my time wading through their red-tape.  And btw, Adobe knows the customer will WIN any chargeback because this evidence of a known to be defective product was sold to the consumer and the customer even allowed the mfg to remediate the issue only they failed to deliver in a timely fashion.  So, if one is not happy just "go to the mattresses"...use the chargeback hammer.  The bonus is every chargeback granted to the consumer costs the retailer, Adobe in my case, $35 when they lose...

  • My ipod touch stopped working out of no where and now it wont turn  on what should i do?

    my ipod touch stopped working out of no where how do i turn it on?

    Try a hard reset.
    Basic troubleshooting steps. 
    17" 2.2GHz i7 Quad-Core MacBook Pro  8G RAM  750G HD  120G Vertex 3 SSD Boot HD  

  • Help, my indesign doc won't stop putting 1 in front of text box..

    hi
    My indesign document won't stop putting the prefix 1 in front of the sentence i write in my text box?
    Lisa

    You probably hit the Numbered List on the control panel (top). Just deselect it and it should be fine.

  • My iPad no longer puts out sound it was in my backpack will it was raining and don't know if that's what caused it pls help

    My iPad no longer puts out sound it was in my backpack will it was raining and don't know if that's what caused it pls help

    A possible cause is a problem with the file places.sqlite that stores the bookmarks and the history.
    *http://kb.mozillazine.org/Bookmarks_history_and_toolbar_buttons_not_working_-_Firefox
    *https://support.mozilla.org/kb/Bookmarks+not+saved#w_fix-the-bookmarks-file
    You can also try to repair the places database with this extension:
    *https://addons.mozilla.org/firefox/addon/places-maintenance/

Maybe you are looking for