DEFAULT GATEWAY ERROR

we recently installed microsoft outlook 2013 in windows 7 in our office whille we are trying to connect the outlook to exchange server it show some message
message appearing on my screen is :The action can nt completed.The microsoft exchanage is unavaliable.your network adapter doesnt have the default gateway error.
In microsoft exchange community we seen some solution and that solutions are also tried we get solution for this problem,so please suggest us solution to this problem.

Hi,
If your client doesn't have a Default Gateway, then you need to create a Dword named
DefConnectOpts, value "0" in the registry at HKEY_CURRENT_USER\Software\Microsoft\Office\15.0\Outlook\RPC
See: http://support.microsoft.com/kb/913843
If you do have Default Gateway, then may I ask if you are connecting to an Exchange Server over Direct Access?
Martina Miskovic

Similar Messages

Loss of default gateway - to auto-shutdown radio

Hi,
I need a solution where, if an access point looses its connection to its default gateway, that it automatically shuts the radio down. And when the default gateway is again available, the radio is automatically turned on again. By connection, I do not just mean that the AP FastEthernet port link status changes.
Some kind of functionality like the 'track rtr reachability' that probes the default gateway, and takes action if the default gateway cannot be reached.
How to, if at all possible...
Problem is that wireless equipment will connect to the access point if the radio is up but the access point does not have access to its default gateway (for some error reason other than the local Ethernet link, but also that...)
Thanks
Johnny

Hi,
unfortunately that does not solve this problem:
Router (def. gw for WAP)
Switch 1
Switch 2
Wireless Access Point (WAP)
If switch 1 is down or if the link from switch 1 to the router is down, then the WAP radio will still be up. I need for it to handle a loss to its default gateway, not just its local ethernet wire.
Tx
Johnny

Default Gateway when connected to VPN

Thanks for reading!
This is probably a dump question so bear with me...
I have set up a VPN connection with a Cisco ASA 5505 fronting internet, with the customers environment behind it (on the same subnet), When connected ot the VPN I can reach the inside Router fronting me and one switch behind the Router (every switch is connected to the router), but nothing else.
My beet is that the Router is messing with my connection, but,, nevermind that!, the setup ain't complete anyway... my question is more related to the Gateway I'm missing when I'm, from the outside, is connected to the VPN on the ASA, could this mess it up? Shouldn't I have a Standard-Gateway in the ipconfig settings in windows?
This is who it looks like now:
        Anslutningsspecifika DNS-suffix . : VPNOFFICE
        IP-adress . . . . . . . . . . . . : 10.10.10.1
        Nätmask . . . . . . . . . . . . . : 255.255.255.0
        Standard-gateway . . . . . . . . :
The internal network is :
172.16.12.0 255.255.255.0
Below is my config for the ASA, thanks a lot!!!!!!!
!FlASH PÅ ROUTERN FRÅN BÖRJAN
!asa841-k8.bin
hostname DRAKENSBERG
domain-name default.domain.invalid
enable password XXXXXXX
names
interface Vlan1
nameif inside
security-level 100
ip address 172.16.12.4 255.255.255.0
interface Vlan10
nameif outside
security-level 0
ip address 97.XX.XX.20 255.255.255.248
interface Ethernet0/0
switchport access vlan 10
interface Ethernet0/1
interface Ethernet0/2
interface Ethernet0/3
interface Ethernet0/4
interface Ethernet0/5
interface Ethernet0/6
interface Ethernet0/7
ftp mode passive
clock timezone CEST 1
clock summer-time CEDT recurring last Sun Mar 2:00 last Sun Oct 3:00
dns server-group DefaultDNS
domain-name default.domain.invalid
object-group protocol TCPUDP
protocol-object udp
protocol-object tcp
access-list nonat extended permit ip 172.16.12.0 255.255.255.0 10.10.10.0 255.255.255.0
access-list MSS_EXCEEDED_ACL extended permit tcp any any
access-list VPN-SPLIT-TUNNEL remark VPN SPLIT TUNNEL
access-list VPN-SPLIT-TUNNEL standard permit 172.16.12.0 255.255.255.0
tcp-map MSS-MAP
exceed-mss allow
pager lines 24
logging enable
logging timestamp
logging buffer-size 8192
logging console notifications
logging buffered notifications
logging asdm notifications
mtu inside 1500
mtu outside 1500
ip local pool VPN 10.10.10.1-10.10.10.40 mask 255.255.255.0
icmp unreachable rate-limit 1 burst-size 1
icmp permit any inside
icmp permit any outside
asdm image disk0:/asdm-625-53.bin
no asdm history enable
arp timeout 14400
global (outside) 1 interface
nat (inside) 0 access-list nonat
nat (inside) 1 172.16.12.0 255.255.255.0
route outside 0.0.0.0 0.0.0.0 97.XX.XX.17 1
timeout xlate 3:00:00
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout uauth 0:05:00 absolute
dynamic-access-policy-record DfltAccessPolicy
aaa authentication ssh console LOCAL
http server enable
http 172.16.12.0 255.255.255.0 inside
no snmp-server location
no snmp-server contact
snmp-server enable traps snmp authentication linkup linkdown coldstart
crypto ipsec transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
crypto ipsec transform-set ESP-DES-SHA esp-des esp-sha-hmac
crypto ipsec transform-set ESP-DES-MD5 esp-des esp-md5-hmac
crypto ipsec transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
crypto ipsec transform-set ESP-3DES-MD5 esp-3des esp-md5-hmac
crypto ipsec transform-set ESP-AES-256-SHA esp-aes-256 esp-sha-hmac
crypto ipsec transform-set ESP-AES-128-SHA esp-aes esp-sha-hmac
crypto ipsec transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
crypto ipsec transform-set ESP-AES-128-MD5 esp-aes esp-md5-hmac
crypto ipsec transform-set ESP-3DES-SHA esp-3des esp-sha-hmac
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set pfs group1
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA ESP-3DES-MD5 ESP-DES-SHA ESP-DES-MD5
crypto map outside_map 65535 ipsec-isakmp dynamic SYSTEM_DEFAULT_CRYPTO_MAP
crypto map outside_map interface outside
crypto isakmp enable outside
crypto isakmp policy 10
authentication pre-share
encryption 3des
hash sha
group 2
lifetime 86400
crypto isakmp policy 65535
authentication pre-share
encryption 3des
hash sha
group 2
lifetime 86400
telnet timeout 5
ssh 172.16.12.0 255.255.255.0 inside
ssh timeout 5
console timeout 0
threat-detection basic-threat
threat-detection statistics access-list
group-policy VPNOFFICE internal
group-policy VPNOFFICE attributes
dns-server value 215.122.145.18
vpn-tunnel-protocol IPSec
split-tunnel-policy tunnelspecified
split-tunnel-network-list value VPN-SPLIT-TUNNEL
default-domain value VPNOFFICE
split-dns value 215.122.145.18
msie-proxy method no-proxy
username admin password XXXXXX privilege 15
username Daniel password XXXXX privilege 0
username Daniel attributes
vpn-group-policy VPNOFFICE
tunnel-group VPNOFFICE type remote-access
tunnel-group VPNOFFICE general-attributes
address-pool VPN
default-group-policy VPNOFFICE
tunnel-group VPNOFFICE ipsec-attributes
pre-shared-key XXXXXXXXXX
class-map MSS_EXCEEDED_MAP
match access-list MSS_EXCEEDED_ACL
class-map inspection_default
match default-inspection-traffic
policy-map type inspect dns preset_dns_map
parameters
message-length maximum 512
policy-map global_policy
class inspection_default
inspect dns preset_dns_map
inspect ftp
inspect h323 h225
inspect h323 ras
inspect netbios
inspect rsh
inspect rtsp
inspect skinny
inspect esmtp
inspect sqlnet
inspect sunrpc
inspect tftp
inspect sip
inspect xdmcp
inspect icmp error
inspect pptp
inspect ipsec-pass-thru
inspect icmp
class MSS_EXCEEDED_MAP
set connection advanced-options MSS-MAP
service-policy global_policy global
privilege cmd level 3 mode exec command perfmon
privilege cmd level 3 mode exec command ping
privilege cmd level 3 mode exec command who
privilege cmd level 3 mode exec command logging
privilege cmd level 3 mode exec command failover
privilege cmd level 3 mode exec command packet-tracer
privilege show level 5 mode exec command import
privilege show level 5 mode exec command running-config
privilege show level 3 mode exec command reload
privilege show level 3 mode exec command mode
privilege show level 3 mode exec command firewall
privilege show level 3 mode exec command asp
privilege show level 3 mode exec command cpu
privilege show level 3 mode exec command interface
privilege show level 3 mode exec command clock
privilege show level 3 mode exec command dns-hosts
privilege show level 3 mode exec command access-list
privilege show level 3 mode exec command logging
privilege show level 3 mode exec command vlan
privilege show level 3 mode exec command ip
privilege show level 3 mode exec command ipv6
privilege show level 3 mode exec command failover
privilege show level 3 mode exec command asdm
privilege show level 3 mode exec command arp
privilege show level 3 mode exec command route
privilege show level 3 mode exec command ospf
privilege show level 3 mode exec command aaa-server
privilege show level 3 mode exec command aaa
privilege show level 3 mode exec command eigrp
privilege show level 3 mode exec command crypto
privilege show level 3 mode exec command vpn-sessiondb
privilege show level 3 mode exec command ssh
privilege show level 3 mode exec command dhcpd
privilege show level 3 mode exec command vpnclient
privilege show level 3 mode exec command vpn
privilege show level 3 mode exec command blocks
privilege show level 3 mode exec command wccp
privilege show level 3 mode exec command webvpn
privilege show level 3 mode exec command module
privilege show level 3 mode exec command uauth
privilege show level 3 mode exec command compression
privilege show level 3 mode configure command interface
privilege show level 3 mode configure command clock
privilege show level 3 mode configure command access-list
privilege show level 3 mode configure command logging
privilege show level 3 mode configure command ip
privilege show level 3 mode configure command failover
privilege show level 5 mode configure command asdm
privilege show level 3 mode configure command arp
privilege show level 3 mode configure command route
privilege show level 3 mode configure command aaa-server
privilege show level 3 mode configure command aaa
privilege show level 3 mode configure command crypto
privilege show level 3 mode configure command ssh
privilege show level 3 mode configure command dhcpd
privilege show level 5 mode configure command privilege
privilege clear level 3 mode exec command dns-hosts
privilege clear level 3 mode exec command logging
privilege clear level 3 mode exec command arp
privilege clear level 3 mode exec command aaa-server
privilege clear level 3 mode exec command crypto
privilege cmd level 3 mode configure command failover
privilege clear level 3 mode configure command logging
privilege clear level 3 mode configure command arp
privilege clear level 3 mode configure command crypto
privilege clear level 3 mode configure command aaa-server
prompt hostname context
Cryptochecksum:aaa1f198bf3fbf223719e7920273dc2e
: end

I didn't realise I had that crypto settings on, thanks my bad!!!
But... the 172.16.12.0 network is directly connected, the Router (that to be honest is a firewall) / switches is all on the same subnet (172.16.12.X/24), so sorry I didn't explain thoroughly, was more wondering about the GW and didn't want to overcomplicate things..
The Firewall/Router dosen't do any routing, so it should work right (I you count out the firewalling in the firewall and so forth, there shouldn't be any problems accomplishing this with the ASA)? The Firewall is more a DHCP for the clients/Firwall for the clients.. this will change in the future.. it will be removed,
the vpn network is staticly routed back to my ASA in that firewall...
I don't like this solution.. but this is who it looks.. for now..
(VPN network is 10.10.10.X/24)
But... shouldn't I see a default gateway under ipconfig when I'm connected to the VPN from internet, on the vpn client that's vpned in, is this correct?
THANKS for all the help!

Set default gateway on headless server (via ssh)

I'm trying to configure one of the two ethernet interfaces on a headless Xserve. I managed to give it an address and subnet mask with ifconfig, but I can't figure out how to give it a default gateway or dns server.
I tried using this:
sudo route add default gw xxx.xxx.xxx.xxx en0
but I got the error 'route: bad address: gw'
is there something wrong with my syntax, or does this just not work on OS X?

Something's wrong with your syntax
Try:
<pre class=command>sudo route add default a.b.c.d</pre>
The keyword 'gw' is not needed, and you also don't need to specify an interface since the OS should be able to work it out from the IP address(es) assigned to your interface(s).

Where we need to put default gateway?

Hi ,
I am installing ORACLE RAC on vmware.
my network setting is in this way.
on node1
eth0 192.168.0.1
eth1 192.168.0.11
on node 2
eth0 192.168.0.2
eth1 192.168.0.22
where should i define default gateway. i.e on eth0 or eth1?
thanks.

Hi chandra,
I did initially but at that time i was getting an error.
after that i set the vip only for eth0 was getting an error but i change the parameter in racgvip it works.
In the previous where i applied vip on both eth0 and eth1 in that i doesnt work.
I am confused. In my case it doesnt work for both unlsess i change the parameter in racgvip.
in both was getting an error default gateway is not defined.
Thanks

WRT300N - Default Gateway issue

I'm using a wireless internet connection for my laptop and when I tried to connect to the internet earlier I got an error telling me that my default gateway was offline. I unplugged everything for 5 minutes and it still didn't work so I typed the default gateway address into the bar and it wouldn't even load (I got an error page). When I went into cmd and typed ipconfig/all my default gateway IP wasn't even listed. How do I get this back online?
Message Edited by Mandie on 01-06-2009 03:24 PM

If you don't have any computer connected to the Internet throught the router is highly possible that you have lost the configuration on your router...You should re-configure your router...
If you have a desktop connected to the router fine, else connect your laptop to ethernet port 1 on the router...Press and hold the reset button for 30 seconds...Release the reset button...Unplug the power cable from your router, wait for 30 seconds and re-connect the power cable...Now re-configure your router...
If your Internet Service Providor is Cable follow this
If your Internet Service Providor is DSL follow this

Default gateway arp lookup failed

Hi there
On a 5500 series WLC I see I have an issue where peap clients get randomly disconnected with these errors
MAX_EAPOL_KEY_RETRANS: 1x_ptsm.c:444 Max EAPOL-key M1 retransmissions exceeded for client 24:77:03:35:79:34
AAA-6-ARP_LOOKUP_FAIL: radius_db.c:3232 Default gateway arp lookup failed.
aaaQueueReader: Aug 31 19:12:14.938: %AAA-4-RADIUSMSG_SEND_FAILED: radius_db.c:3567 Unable to send RADIUS message to
Any ideas?
Thanks
Naresh
Sent from Cisco Technical Support iPhone App

(Cisco Controller) >show wlan 1
WLAN Identifier.................................. 1
Profile Name..................................... SSID1
Network Name (SSID).............................. SSID1
Status........................................... Enabled
MAC Filtering.................................... Disabled
Broadcast SSID................................... Enabled
AAA Policy Override.............................. Enabled
Network Admission Control
Radius-NAC State............................... Disabled
SNMP-NAC State................................. Disabled
Quarantine VLAN................................ 0
Maximum number of Associated Clients............. 0
Number of Active Clients......................... 0
Exclusionlist Timeout............................ 60 seconds
Session Timeout.................................. 1800 seconds
CHD per WLAN..................................... Enabled
Webauth DHCP exclusion........................... Disabled
Interface........................................ i_wifi
Multicast Interface.............................. Not Configured
WLAN ACL......................................... unconfigured
DHCP Server...................................... Default
DHCP Address Assignment Required................. Enabled
Static IP client tunneling....................... Disabled
Quality of Service............................... Silver (best effort)
Scan Defer Priority.............................. 4,5,6
Scan Defer Time.................................. 100 milliseconds
WMM.............................................. Allowed
WMM UAPSD Compliant Client Support............... Disabled
Media Stream Multicast-direct.................... Disabled
CCX - AironetIe Support.......................... Enabled
CCX - Gratuitous ProbeResponse (GPR)............. Disabled
CCX - Diagnostics Channel Capability............. Disabled
Dot11-Phone Mode (7920).......................... Disabled
Wired Protocol................................... None
IPv6 Support..................................... Disabled
Passive Client Feature........................... Disabled
Peer-to-Peer Blocking Action..................... Drop
Radio Policy..................................... All
DTIM period for 802.11a radio.................... 1
DTIM period for 802.11b radio.................... 1
Radius Servers
   Authentication................................ 1.1.1.1 1812
   Authentication................................ 1.2.1.1 1812
   Accounting.................................... 1.1.1.1 1813
   Accounting.................................... 1.2.1.1 1813
   Dynamic Interface............................. Enabled
Local EAP Authentication......................... Disabled
Security
   802.11 Authentication:........................ Open System
   Static WEP Keys............................... Disabled
   802.1X........................................ Disabled
   Wi-Fi Protected Access (WPA/WPA2)............. Enabled
      WPA (SSN IE)............................... Disabled
      WPA2 (RSN IE).............................. Enabled
         TKIP Cipher............................. Disabled
         AES Cipher.............................. Enabled
      Auth Key Management
         802.1x.................................. Enabled
         PSK..................................... Disabled
         CCKM.................................... Enabled
         FT(802.11r)............................. Disabled
         FT-PSK(802.11r)......................... Disabled
FT Reassociation Timeout......................... 20
FT Over-The-Air mode............................. Enabled
FT Over-The-Ds mode.............................. Enabled
CCKM tsf Tolerance............................... 1000
   CKIP ......................................... Disabled
   Web Based Authentication...................... Disabled
   Web-Passthrough............................... Disabled
   Conditional Web Redirect...................... Disabled
   Splash-Page Web Redirect...................... Disabled
   Auto Anchor................................... Disabled
   H-REAP Local Switching........................ Disabled
   H-REAP Local Authentication................... Disabled
   H-REAP Learn IP Address....................... Enabled
   Client MFP.................................... Optional
   Tkip MIC Countermeasure Hold-down Timer....... 60
Call Snooping.................................... Disabled
Roamed Call Re-Anchor Policy..................... Disabled
SIP CAC Fail Send-486-Busy Policy................ Enabled
SIP CAC Fail Send Dis-Association Policy......... Disabled
Band Select...................................... Disabled
Load Balancing................................... Disabled
Mobility Anchor List
WLAN ID     IP Address            Status

Can't find the option to disable "Default Gateway" of a VPN.

Whenever I try to go to the "Networking" tab of a VPN connection. I get the following error.: "Unable to allow the editing of networking components at this time because they are currently being modified elsewhere" This prevents me from
disabling the default gateway of a VPN. Any help is greatly appreciated!

Whenever I try to go to the "Networking" tab of a VPN connection. I get the following error.: "Unable to allow the editing of networking components at this time because they are currently being modified elsewhere" This prevents
me from disabling the default gateway of a VPN. Any help is greatly appreciated!
I have got the same issue using Windows 10 Insider Preview build 10074, please could somebody show us an alternative method to disable the use of the remote default gateway through a VPN ? Thanks.
Edit - From that post : https://social.technet.microsoft.com/Forums/en-US/709f9e02-d903-41a8-b5f8-d0f46d4685bf/how-to-disable-default-gateway-remote-in-vpm-with-windows-10-tp-10049?forum=WinPreview2014General
it seems to be possible to use a PowerShell command to modify this option, by setting "RouteIPv4TrafficOverRAS" to "False" instead of "True" (which is WIndows Default), but I do not know how to do that. Could somebody explain

How to configure default gateway Solaris 9

How to configure default gateway using /etc/gateways file (NO /etc/defaultrouter).
The line "net default gateway ip_router metric 1 passive" produce the following error message:
in.routed: bad net "default" in /etc/gateways entry "net default gateway ip_router metric 1 passive"--cannot be default.
With Solaris 8 is ok.
Can you help me.

you've probably worked this out by now, but this may help others;
net 0.0.0.0 gateway x.x.x.x metric 1 passive
* x.x.x.x = your gateway IP

Change default gateway using *netipaddress* cmdlet

Hi, is there a way to change the DFG after the IP is assigned to an adapter?
I am using Server 2012. I created a new IP using "new-netipaddress -Ipaddress 1.2.3.4 -prefixlength 24 -interfaceindex 10". I have forgotten to add the -defaultgateway parameter in the command. IP address was sucessfully assigned, but I cannot figure out
a way to change/add a default gateway.
Does anyone know how to do it via native powershell cmdlets (no gwmi, functions or scripts)?
Cheers

I am having a similar problem and using Remove-NetIPAddress does not really help. Remove-NetIPAddress does not affect gateway settings and gateways remain assigned to the net adapter. Furthermore, after I use RemoveNetIPAddress cmdlet, the NetTCPIP\Get-NetIPConfiguration
cmdlet starts producing a non-terminating error. Here is a repro script:
PS C:\> $IPAddress = '192.168.0.1'
PS C:\> $DefaultGateway = '192.168.0.1'
PS C:\>
PS C:\> # Enumerate NIC configurations.
PS C:\> $networks = NetTCPIP\Get-NetIPConfiguration
Exception setting "NetProfile": "Cannot convert the "System.Object[]" value of type "System.Object[]" to type
"Microsoft.Management.Infrastructure.CimInstance"."
At C:\Windows\system32\WindowsPowerShell\v1.0\Modules\NetTCPIP\NetIPConfiguration.psm1:128 char:13
+             $IPConfig.NetProfile = Get-NetConnectionProfile -InterfaceAlias $IfA ...
+ ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
    + CategoryInfo          : NotSpecified: (:) [], SetValueInvocationException
    + FullyQualifiedErrorId : ExceptionWhenSetting
PS C:\> # Look for NIC that is not on corpnet.
PS C:\> $privateNetwork = $networks | ? { $_.IPv4Address.PrefixOrigin -ne 'Dhcp'}
PS C:\> $privateNetworkName = $privateNetwork.InterfaceAlias
PS C:\> $privateNic = NetAdapter\Get-NetAdapter -Name $privateNetworkName
PS C:\> $privateNic | NetTCPIP\Set-NetIPInterface -Dhcp Disabled
PS C:\> $privateNic | NetTCPIP\Remove-NetIPAddress -Confirm:$false
PS C:\> $privateNic | NetTCPIP\New-NetIPAddress -IPAddress $IPAddress -PrefixLength 24 -DefaultGateway $DefaultGateway
NetTCPIP\New-NetIPAddress : Instance DefaultGateway already exists
At line:1 char:15
+ $privateNic | NetTCPIP\New-NetIPAddress -IPAddress $IPAddress -PrefixLength 24 - ...
+ ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
    + CategoryInfo          : InvalidArgument: (MSFT_NetIPAddress:ROOT/StandardCimv2/MSFT_NetIPAddress) [New-NetIPAddr
   ess], CimException
    + FullyQualifiedErrorId : Windows System Error 87,New-NetIPAddress

VPN Client : Default Gateway

Hi,
I have ASA 5505 with ASA v 8.0.3 and ASDM v 6.0.3.
The VPN connection works, the client receive the IP from the define pool but the default gateway is not correct. Is it possible to define the gateway in the pool ?
thank you

Dimitri
I am not clear what default gateway you expected, what default gateway you got, or what was no correct about the gateway. Perhaps you can clarify?
In my experience many people are surprised that the gateway address is the clients own address and not some other address in the subnet as we normally expect with a LAN client. But this is normal behavior on what is essentially a point to point connection from the client to the concentrator. Is this perhaps what you were thinking was an error?
HTH
Rick

Meetingplace server crash and lost the default gateway info

HI all
I have ver 2.0.1.15. I have first eth0 on ip 10.1.1.18 and 2nd eth1 192.168.162.21. will crash and the default gateway on eth0 will be gone. Am i doing something wrong.

Shannon,
Harry is asking you the right question, because a theme with any bad syntax in it (especially custom XSLT files) will get scrapped when the server restarts.
Try to think of something you changed recently, revert it to see of the theme will show up, and try to find the syntax error in your recent changes.
This caught me by surprise when it first happened, but I suppose it is a nice feature. The Wiki Server falls back on a theme that works, which are the built-in ones. It would be nice if the errors were logged instead of just scrapping the theme, but I assume the spirit is to give you a wiki that works, rather than a nicely themed wiki that has errors.

Setting permanent default gateway in OEL 6

Hello,
how can a default gateway be set permanently in OEL6?
At the moment I am setting iit manually every time the machine or the network service is restarted:
$ /sbin/route add -net default gw IPADDRESSThanks on advance.
Angel

Hi again,
looks like we managed to achieve the target following the steps in section 4.4 of the Deployment manual at http://linux.oracle.com/documentation/EL6/Red_Hat_Enterprise_Linux-6-Deployment_Guide-en-US.pdf. The link you provided was pointing to Development manual.
I created a file /etc/sysconfig/network-scripts/route-bond0.764 with the following content:
0.0.0.0/0 via 10.7.79.250 dev bond0.764Using the "network/netmask" format. That way it works all right:
$netstat -rn
Kernel IP routing table
Destination Gateway Genmask Flags MSS Window irtt Iface
0.0.0.0 10.7.79.250 0.0.0.0 UG 0 0 0 bond0.764Just for FYI, first of all I tried with the following content:
default 10.7.79.250 dev bond0.764But when bouncing the network service, I was getting this error:
Bringing up interface bond0.764: Error: either "to" is a duplicate, or "10.7.79.250" is a garbage.'Not sure which was the reason for this error anyway.
Looks like when using channel bonding, gateway specification in the usual files (/etc/sysconfig/network or /etc/sysconfig/network-scripts/ifcfg-bond* ) makes no effect for any reason.
Let me know if I can do something to find out why it makes no effect.
Thanks a lot for you help.
Angel
Let me know if I can help

The Default Gateway Is Not Available / Problem

Hello, I recently purchased this HP Pavileon laptop, and I've been encountering this problem very often (every 2-10 minutes). This problem is getting extremely frustrating as absolutely nobody has been able to provide a fix for this issue.
When the laptop is on battery mode (this does not happen when plugged in); I commonly get disconnected from my wi-fi connection and to fix it, I must run the troubleshooter. This temporarily fixes the issue by resetting the wi-fi adapter.
What I have tried and has not worked:
* Turn off to save power option in the driver settings (in Device Manager) untickets
* Updated drivers
* New power plan
* Tried different drivers
* Complete system restore
The wireless adapter is Realtek RTL 8188EE. Upon running the troubleshooter, this is all the information from the detailed information section:
Windows Network Diagnostics
Publisher details
Issues foundThe default gateway is not available
The default gateway is not availableThe default gateway is a device that connects a local network or computer to the Internet. A broadband modem or router is usually the default gateway.
Fixed
Reset the "WiFi" adapter
Completed
Investigate router or broadband modem issues
Not run
Issues found
Detection details
6The default gateway is not availableFixed
The default gateway is a device that connects a local network or computer to the Internet. A broadband modem or router is usually the default gateway.
Reset the "WiFi" adapterCompleted
This can sometimes resolve an intermittent problem.
Network Diagnostics LogFile Name: 2D0FE1F0-C2C2-43B5-A857-2D2B3C4B8A51.Repair.1.etl Investigate router or broadband modem issuesNot run
If you're connected to a hotspot or domain network, contact the network administrator. Otherwise: 1. Unplug or turn off the device. 2. Once all the lights on the device are off, wait at least 10 seconds. 3. Turn the device on or plug it back in to the power outlet. To restart a router or modem that has a built-in battery, press and quickly release the Reset button.
Detection details
Diagnostics Information (Network Adapter)
Details about network adapter diagnosis:
Network adapter WiFi driver information:
Description . . . . . . . . . . : Realtek RTL8188EE 802.11b/g/n Wi-Fi Adapter
Manufacturer . . . . . . . . . : Realtek Semiconductor Corp.
Provider . . . . . . . . . . . : Realtek Semiconductor Corp.
Version . . . . . . . . . . . : 2012.2.827.2013
Inf File Name . . . . . . . . . : C:\WINDOWS\INF\oem8.inf
Inf File Date . . . . . . . . . : 12 September 2013 10:17:00
Section Name . . . . . . . . . : HP8188ee.ndi
Hardware ID . . . . . . . . . . : pci\ven_10ec&dev_8179&subsys_197d103c
Instance Status Flags . . . . . : 0x180200a
Device Manager Status Code . . : 0
IfType . . . . . . . . . . . . : 71
Physical Media Type . . . . . . : 9
Diagnostics Information (Wireless Connectivity)
Details about wireless connectivity diagnosis:
Information for connection being diagnosed
Interface GUID: 7c04789b-0b43-472c-abd6-a84cb31e9053
Interface name: Realtek RTL8188EE 802.11b/g/n Wi-Fi Adapter
Interface type: Native WiFi
Connection incident diagnosed
Auto Configuration ID: 1
Connection ID: 1
Connection status summary
Connection started at: 2014-07-24 04:19:49-759
Profile match: Success
Pre-Association: Success
Association: Success
Security and Authentication: Success
List of visible access point(s): 0 item(s) total, 0 item(s) displayed
Connection History
Information for Auto Configuration ID 1
List of visible networks: 1 item(s) total, 1 item(s) displayed
BSS Type PHY Security Signal(RSSI) Compatible SSID
Infra <unknown> Yes 100 Yes Matt
List of preferred networks: 1 item(s)
Profile: Matt
SSID: Matt
SSID length: 4
Connection mode: Infra
Security: Yes
Set by group policy: No
Connect even if network is not broadcasting: No
Connectable: Yes
Information for Connection ID 1
Connection started at: 2014-07-24 04:19:49-759
Auto Configuration ID: 1
Profile: Matt
SSID: Matt
SSID length: 4
Connection mode: Infra
Security: Yes
Pre-Association and Association
Connectivity settings provided by hardware manufacturer (IHV): No
Security settings provided by hardware manufacturer (IHV): No
Profile matches network requirements: Success
Pre-association status: Success
Association status: Success
Last AP: 98-fc-11-88-61-b8
Security and Authentication
Configured security type: WPA2-PSK
Configured encryption type: CCMP(AES)
802.1X protocol: No
Key exchange initiated: Yes
Unicast key received: Yes
Multicast key received: Yes
Number of security packets received: 0
Number of security packets sent: 0
Security attempt status: Success
Connectivity
Packet statistics
Ndis Rx: 34302
Ndis Tx: 32619
Unicast decrypt success: 0
Multicast decrypt success: 0
Unicast decrypt failure: 0
Multicast decrypt failure: 0
Rx success: 0
Rx failure: 0
Tx success: 0
Tx failure: 0
Tx retry: 0
Tx multiple retry: 0
Tx max lifetime exceeded: 0
Tx ACK failure: 0
Roaming history: 0 item(s)
Diagnostics Information (Wireless Connectivity)
Details about wireless connectivity diagnosis:
For complete information about this session see the wireless connectivity information event.
Helper Class: Auto Configuration
Initialise status: Success
Information for connection being diagnosed
Interface GUID: 7c04789b-0b43-472c-abd6-a84cb31e9053
Interface name: Realtek RTL8188EE 802.11b/g/n Wi-Fi Adapter
Interface type: Native WiFi
Result of diagnosis: There may be problem
Diagnostics Information (Wireless Network Adapter)
Details about wireless network adapter diagnosis:
For complete information about this session see the wireless connectivity information event.
Helper Class: Native WiFi MSM
Initialise status: Success
Information for connection being diagnosed
Interface GUID: 7c04789b-0b43-472c-abd6-a84cb31e9053
Interface name: Realtek RTL8188EE 802.11b/g/n Wi-Fi Adapter
Interface type: Native WiFi
Profile: Matt
SSID: Matt
SSID length: 4
Connection mode: Infra
Security: Yes
Connect even if network is not broadcasting: No
Result of diagnosis: There may be problem
Network Diagnostics LogFile Name: 2D0FE1F0-C2C2-43B5-A857-2D2B3C4B8A51.Diagnose.0.etl
Other Networking Configuration and LogsFile Name: NetworkConfiguration.cab Collection information Computer Name: LAPTOP Windows Version:6.3Architecture:x64Time:24 July 2014 04:34:47
Windows Network Diagnostics Detects problems with network connectivity. Package Version:1.0Publisher:Microsoft Windows

Run the HP Support Asssitant's Tune up application. There should be a new BIOS available. sp66866
Have you installed the latest Windows 8.1 updates?
Do not install optional video graphics updates.
I was runnning into a similar problem with my HP product loan Envy Spectre 13 TouchSmart Ultrabook until I did the updates. I had upgraded my wireless router to a model with 802.11AC specification.
Invoke the Device Manager and ensure that the box next to Allow this computer to turn off this device to save power is unchecked.
****Please click on Accept As Solution if a suggestion solves your problem. It helps others facing the same problem to find a solution easily****
2015 Microsoft MVP - Windows Experience Consumer

How to fix gateway error in a View Page?

I have created an override view page and I need to add a button or link which should take the user to a page in different server. I am getting gateway error. The sample code as follows. Any thougts will be helpful. Thanks in advance.
string sUrl = "<pt:gatewayLink pt:href='http://appserver/step1.asp' pt:objectID='206' pt:classID='35' xmlns:pt='http://www.plumtree.com/xmlschemas/ptui/'/>"; HTMLAnchor myAnchor = new HTMLAnchor(sUrl); myAnchor.AddInnerHTMLString("Add a Logo"); myCell.AddInnerHTMLElement(myAnchor);

i think, something is wrong in the approach itself.
when you include the code, you do not need to create a new
instance of Hmenu. Instead, you can simply use lnkBar .addChild(),
because the this code is of your Hmenu itself.
But i suggest you to use dataprovider for the linkbar instead
of looping through the categories and adding the child.
you just declare xmlData as Bindable and provide it as
dataProvider of the linkbar.
hope it works.

DEFAULT GATEWAY ERROR

Similar Messages

Maybe you are looking for