Default Remote Management Settings

I just (for the first time ever) looked at my Remote Management settings and VNC access was turned on and Show status in menu bar was turned off. That seems a bit precarious and unorthodox.
Is that the default setting or has my system been changed by someone/thing? Is there a way to easily parse my secure.log (i.e., a useful string to search for) that would tell me if I have had unauthorized connections?

Try the following steps:
A] With the help of Cisco Connect Software (if at all you have installed the router with the help of this software)
1] Open the software and go to the option which says "Router Settings"
2] Then click on the option which says "Advanced Settings" which will take you to the router's configuration page.
3] Then click on Security tab disable SPI Firewall Protection, uncheck Filter Anonymous Internet Requests...
B] If you haven't installed Cisco Connect then you can log on to the router's user interface using it's default IP address in the browser which is 192.168.1.1 and type in 'admin' as the password leaving the username field blank. This will take you to the router's web interface and then follow steps as mentioned above to make the changes.

Similar Messages

Changed Remote Management Settings -- Lost ARD Control!

I run a headless server. My remote management settings on the server were set to allow "all users" to control it. I changed it to allow "only these users" and it was set to the current and only user "admin". I immediately lost control of the server in ARD. When I try to re-add it to my list, it accepts "admin" and the password but refuses to allow me to control the server anymiore.
Needless to say: Help!

well, that was exciting . . . i was able to login as the superuser (root).
what's interesting is that when i re-established contact with the server the remote management/options window was open and none of the boxes were checked.
since it limited control to the admin user immediately upon selecting it, therefore, it stopped allowing me to control it via ARD. not sure how one could set control the admin only on a headless server, but all's well that ends well.

Remote Management settings

I am trying to turn on my screen sharing but when I go to the system preferences "Sharing" tab, and click on the "Screen Sharing" and the message "Screen Sharing is currently being controlled by the Remote Management service". I naturally go to the remote management tab, but it is not there. Any help?
I am using a late 2010 MBA

If your users have local administrator privileges, there's no way I know of to totally prevent them from being able to alter the settings. You can, if you're using Managed Preferences from Mac OS X Server, turn off access to the Sharing control panel, I believe, but that won't stop a knowledgeable user from just using the kickstart command to alter the ARD settings or turn the ARD client off again.

How to manage Remote Management settings with Snow Leopard Server

At my business, I manage our Macs' preferences using Managed Client as part of Mac OS X Server 10.6... one thing I have not been able to figure out is how to enforce settings for Remote Management. For example: I want only the administrator user to be able to control a machine, and only run reports but not copy software, etc.
I have tried configuring a machine correctly, then importing com.apple.RemoteManagement.plist and com.apple.ARDAgent.plist into Workgroup Manager. No luck. I wonder if anyone out there has solved a similar problem.

Open the Server Admin program (in the dock if nowhere else). It's there.

Changed Remote Management settings, now I can't authenticate!

I recently changed some settings on several machines at my workplace, and one of the settings was to allow all accounts, and not just the previously existing accounts, to access some computers using Remote Management.
I didn't turn Remote Management off, I just changed it from "Allow access for: Only these users:" to "Allow access for: All users". The host machine has 10.6.3 and ARD 3.3.2. All the clients have either 10.6.3 or 10.5.8. Any machines that I haven't changed that setting for work great, and I am able to authenticate, just the ones that I have changed their settings.
I have noticed that when I use an account that is valid on that machine, it colors the icon as if I had put a proper username/password in. I have tried new preference files, I have done the "kickstart" processes, and I have tried ScreenSharing.app, and none of them work. I have tried ScreenSharing.app from other computers, and it fails as well, telling me the problem is with the affected client computers, and not the host.
Any help would be much appreciated.

Okay, I just had an "oh yeah!" moment where it suddenly dawned on me; when I change from "Only these users:" to "All users", I need to adjust the Options... settings to allow for users to remotely connect again.

Blocking rights to change Remote Management Settings

I'm in a school system, and we're getting ZW 7 set up. I have a couple
of users per school who have rights through iManager to reset passwords
for users in their containers. I'm seeing through Console 1 that these
users also are granted Remote Control rights, based on their iManager
Role rights. I can live with that, but I need to block their ability to
change the properties of the package, such as blocking them from
unchecking the option that requires permission from the user before
allowing remote control. Any advice?
Thanks.

sherryhill,
It appears that in the past few days you have not received a response to your
posting. That concerns us, and has triggered this automated reply.
Has your problem been resolved? If not, you might try one of the following options:
- Visit http://support.novell.com and search the knowledgebase and/or check all
the other self support options and support programs available.
- You could also try posting your message again. Make sure it is posted in the
correct newsgroup. (http://forums.novell.com)
Be sure to read the forum FAQ about what to expect in the way of responses:
http://forums.novell.com/faq.php
If this is a reply to a duplicate posting, please ignore and accept our apologies
and rest assured we will issue a stern reprimand to our posting bot.
Good luck!
Your Novell Product Support Forums Team
http://support.novell.com/forums/

Printing Colour Issues - colour management settings

Hi there
I've been having some serious printing problems recently when I print from InDesign CS5 and also from Acrobat when printing PDFs exported from InDesign.
All of the print out colours a wrong (such as Blacks printing as pink)
I have tried changing several settings, but nothing seems to be fixing it.
I've replaced all my inks and I can print fine when printing in other programs such as word, so its not an ink issue.
My printer is a Canon MP540
I'm using a Mac, on OS X Lion.
I think i'm using the default colour management settings, however could this possibly be the issue?- which settings might work?
I would REALLY APPRECIATE any help with this issue!
Many Thanks

if I look at the same image in the default 'Preview' on Mac, the
colours look different to what I see in PS
First, that would clearly indicate your image does not have an embedded profile, or Ps is being told to ignore the embedded profile — Ps is applying a different profile (or it may have been dinked around with in its Edit> Color Settings> More Options> Advanced Controls).
It is best for most people not to dink around with Color Settings> More Options...to get back a Default starting point, just select a preset like North American Prepress 2.
I know there are a million posts and articles on this complex subject
You only need one good article to grasp the basic issues.
The short answer is you are either missing something in scenario One, or you are hitting a bug.
When Photoshop setups a correct SourceSpace-to-PrintSpace Conversion the Epson will print your file faithfully if your Source Color is within print gamut and your Print Space reflects an accurate ICC profile to the specific printer-paper-ink you are printing to.
I would recommend testing with a known good file like the download Photodisc PDI test image (so bad files don't confuse the process)...

Device Manager settings & Intel Rapid Storage for Crucial SSD

Hello, 1. Can anyone tell me what should the settings in device manager be for my drive?See snapshot attached and advise if it is correct. 2. Would there be any collision or problems with having the Intel Rapid Storage client installed?It was already installed in my laptop.

Default device manager settings, under policies, should be top box ticked, second box unticked. These are the correct settings.
IRST is fine as long as it's reasonably new. Like around about v11 or better. Older versions will break windows update (amongst other things) on these modern drives.

Manage Remote Desktop Settings

We have this set to "NO" in our client settings. However, I can right click on any client in the console and start the remote desktop client and connect successfully using RDP. So what exactly does the "Manage Remote Desktop Settings"
do?

>Where I am still confused is what the settings apply to.
> And what if RDP is already enabled by
me manually on a Windows machine? Than setting it to "yes" or "no" has no effect?
If "Manage Remote Desktop" settings is set to "No", then the client leaves the settings alone. Devices should continue on with whatever they have set locally.
If "Manage Remote Desktop" settings is set to "Yes", then the client will change the settings on devices to enable RDP and, optionally, add permitted viewers to the local "Remote Desktop Users" group or require network level authentication. according
to what you specify.
Nash Pherson, Senior Systems Consultant
Now Micro -
My Blog Posts
If you found a bug or want the product to work differently,
share your feedback.
<-- If this post was helpful, please click the up arrow or propose as answer.

Guide to remote manage Hyper-V servers and VM's in workgroups or standalone

This guide is based on the following 3 products:
Windows server 2012 (core)
Windows 8
Hyper-V server v3 / Hyper-V server 2012
The following guide will enable you to:
1: remotely manage your Hyper-V Virtual Machines with Hyper-V manager
2: remotely manage your Hyper-V servers' firewall with a MMC snap-in.
3: remotely manage your Hyper-V server (2012) with server manager
! This should also work for Core installations of server 2012, but I haven't tried.
This guide is purely focussed on servers in a WORKGROUP, or as a stand alone.
I CAN NOT tell you what you need to do to get it working in a domain.
* You can run these commands straight from the console (Physically at the machine) or through RDP.
* You will need to be logged on as an administrator.
* Commands are listed in somewhat random order; I do however advise to follow the steps as listed.
* Commands with ? in front of them are only ment to be helpfull for troubleshooting,
* and to identify settings and changes made.
* Commands and instructions with ! in front of them are mandatory.
- server: means the server core or hyper-v server (non gui)
- client: means the machine you want to use for remote administration.
- Some commands are spread over 2 lines; be sure to copy the full syntax.
> To enable the Hyper-V manager to connect to your server, you need to perform the following 2 actions: (Assuming you have already installed the feature)
1:
! Client: Locate the C:\Windows\System32\Drivers\etc\hosts file.
! right-click --> properties --> security
! click --> edit --> add --> YOURUSERNAME or Administrator --> OK
! then select this new user, and tick the "modify"-box under the "allow"-section.
! apply the change, and close.
! doubleclick the file, and open with notepad
! add the ip-address and name of your server (no // or other crap needed)
! Save the file
# I recommend putting a shortcut to this file on the desktop.
# If you change the ip-address of your server (e.g. move the server from staging to a live environment)
# you might forget to do so in the hosts file.
# Hyper-V manager, MMC, RSAT, and Server-manager all rely on the hosts-file to resolve the name.
# some of these might connect to their respective service on an i.p.-level, but some don't.
# This is the main reason you need to modify this file.
! USE AN ELEVATED CMD/POWERSHELL PROMPT TO CONTINUE !
# the next config needs to be done on windows 8.
# It seems that it's already preconfigured under server 2012
2:
! Client: dcomcnfg
! open component services --> computers
! right-click -> my computer -> properties
! select "COM SECURITY" tab
! under "ACCESS PERMISSIONS" select "edit limits"
! select "ANONYMOUS LOGON", and tick "remote access" under ALLOW
# Without this adjustment, you can't connect to your Hyper-V server
# with the Hyper-V manager if you're not in a domain.
> And if you haven't done so already... make sure you have enabled remote management number 4 on the Hyper-V server console.
> Next, is to get the MMC firewall snap-in working.
The reason for this, is to have a GUI available to configure it.
If you're happy without it, you may skip this and use a shell instead to do so.
? server: netsh advfirewall show currentprofile
# shows the current profile (public/domain/private) and its settings
# depending on your needs, you should set the right profile to fit your needs.
# You can easily do this when the MMC snap-in is done. (after you've followed these steps)
! server: netsh advfirewall set currentprofile settings remotemanagement enable
# enables remote management of the firewall on an application level
# (In other words: allows the firewall to be remotely managed)
! server: netsh advfirewall firewall set rule group="Windows Firewall Remote Management" new enable=yes
# allows remote management of the firewall, through the required firewall ports with TCP protocol.
# 4 rules will be updated to allow access: public & Domain, dynamic and endpoint-mapper.
# You can disable/add/change the rule from the MMC snap-in after finishing this guide.
# e.g. set the firewall through the MMC-GUI to only allow specific ip-addresses etc.
? server: netsh advfirewall firewall show rule all
# Shows a list of available rules, and their current state.
# when run from cmd, the list exceeds the maximum length for review.
# (from cmd,type:) start powershell, and run the command from there.
! Client: cmdkey /add:YOURSERVERNAME /user:USERNAMEONTHESERVER /pass:THEPASSWORDOFTHATUSER
# I recommend you to use a username with enough privileges for management
# All capital letters need to be replaced with your input
# CMD answers "credential added successfully" when you're done
! Client: locate MMC, and run it as an admin.
# In windows 8/2012, go to search and type MMC. Right-click the icon,
# and choose run as admin on the bar below.
! Client: application MMC: select "file" --> Add/remove snap-in
! --> (left pane) scroll down to "windows firewall" --> select and click "add"
! select "another computer"
! type the name of the server you want to manage (NO workgroup/ or //, just same name as you typed for cmdkey)
* Part 2 is done.
# Have a look by doubleclicking the firewall icon in the left pane.
# It looks and works the same as the GUI version that you are familiar with.
! Next is the Server Manager.
# Follow the steps listed to get your server listed and manageable in the server manager.
! Client: Open the created Firewall snap-in for your server.
! Find the 3 "Remote Event Log Management" entries in the list of INBOUND rules, and enable them.
! Open powershell --> in cmd windows, type: start powershell
! run the following line in powershell
! Client: in C:\Windows\system32> set-item WSMAN:\localhost\client\trustedhosts -value YOURSERVERNAME -concatenate
# WinRM Security Configuration.
# This command modifies the TrustedHosts list for the WinRM client. The computers in the TrustedHosts list might not be
# authenticated. The client might send credential information to these computers. Are you sure that you want to modify
# this list?
# [Y] Yes [N] No [S] Suspend [?] Help (default is "Y"): y
# I recommend to choose yes; unless you like to pull some more hairs...
! server: winrm qc
# WinRM service is already running on this machine.
# WinRM is not set up to allow remote access to this machine for management.
# The following changes must be made:
# Configure LocalAccountTokenFilterPolicy to grant administrative rights remotely
# to local users.
# Make the changes? y / n
! select yes
! Client: open the server 2012 server manager
! click manage -> add server
! select the DNS tab, and type the name of your server
Done.
You can now manage your remote server through the familiar computer management GUI.
! Right-click your remote server, and select "Computer Management"
A few side notes:
? The Performance tab seems to list the local machine's performance, in stead of the remote servers'
? If you want Windows server backup, you need to right-click the server in the server manager, and select "add roles and features.
? it will then become available under the "computer management" of the remote server.
If you liked this guide you may thank my employer, Mr. Chris W.
for giving me the time to work it all out.
Cheers!

As a little update to the post, I'd like to add that replication, clustering and migration will not work in workgroup environments. Unless someone can provide an additional guide for this, I'd recommend anyone to no even bother to try.
To manage the standalone hyper-v server in a remote location over the internet, I would recommend the following:
Install windows 8 pro (x86 uses less resources!) as a vm on the host, and assign 2 network connections to it.
1 external (shared with host) (be sure you have a dedicated ip-address for it!)
1 internal connection.
What I did was this:
As soon as you've installed the win8 guest, proceed with the guide as described.
For the 1st step of the guide (hosts-file) use the ip-address you will later assign to the "internal" network switch of the host!
In my example, I'm using 10.0.0.1 for the host, and 10.0.0.2 for the guest.
To be clear: I first used the guide on a LAN-environment, and did all the steps from a "real" client to server on the LAN.
Then, installed the win8 guest on the host using the "real" clients' hyper-v manager over the LAN.
Next, assigned the 2 network connections to the VM, and configured them as follows:
external - as you would to be able to make your guest reach the internet.
internal - I used the following config:
ip-address: 10.0.0.2
subnet: 255.255.255.252
gateway - blank
dns - Blank
Now, when you get to the console of the hyper-v server (host) or RDP to it, go to network settings.
You'll see that the internal card has been added here as well.
Configure it as follows:
ip-address: static - 10.0.0.1
subnet: 255.255.255.252
gateway - blank
dns - blank
You should now be able to ping your guest (win8) on 10.0.0.2 if it's running.
Don't forget to enable ping response (option 4 on the host) to test connectivity the other way around as well (guest to host)
When you're done, you'll be able to RDP to the guest OS over the internet, and then connect to the host with server manager, hyper-v manager, and MMC.
Don't forget to enable each module on the hosts' firewall to make the snap-ins work!
Remote volume management requires your guest/client firewall INcoming ports to be enabled as well! not just the host.
Either update the firewall rules from the MMC gui as described in the guide, or use the following commands on the
hosts' powershell:
Enable the firewall rules with the command Enable-NetFirewallRule -DisplayGroup "USE_THE_COMMANDS_BELOW" (include the " " in the command)
Remote Service Management
Remote Volume Management
Remote Event Log Management
Remote Scheduled Tasks Management
Windows Firewall Remote Management
Windows Remote Management
You can get the list with Get-NetFirewallRule -DisplayName *management*
You can get the list with Get-NetFirewallRule -DisplayName *remote*
Commands provided with credits to F. verstegen
Cheers,
Michael.
Sigh...

Mountain Lion Server: add network user to remote management

Hi,
So recently I have upgraded from Lion Server to ML Server. A little disappointing, but whatever, I've moved on and got everything almost back to where I had it with Lion.
My last few issues I believe are related but can't quite figure it out. In Lion I have an admin profile and then a network user profile that I used on my MBP bound with AD. I'm at the stage where my nre network user can log in on the server machine but I can't log in as the network user via screen sharing. I can't add a network user to Remote Management, and with Remote Management enabled Screen Sharing is greyed out. I'd really like this to work.
My second problem is that I can't bind my MBP to the server but even when bound the network user account can't log in.
Any body have any ideas?
Thanks!

I had this problem on a clean install.
The solution was incredibly simple for me, but only after I saw Ross.M's note about opening the Users & Groups settings panel (in the OS System Prefs, not in server) and rebinding to OD server under Login Options.
That was not the solution for me, but under Login Options I discovered a previously unnoticed pref for "Allow network users to login at login window." I had this option set (apparently by default) to "Only these network users:" but with an empty list. Adding my users to the list made it work perfectly.
Talk about KISS

System Image Utility - Create User - Activate Remote Management

When creating an image with system image utility, based on a DVD image instead of a cloned image, I cannot create a user and activate Remote Management.
I have created an installer package with Apple Remote Desktop that is supposed to do both, however it doesn't work. I do not get an error, but no user is created.
I have tried a post-install script however the dscl command is not recognized even if I put the path /usr/bin/dscl.
I even tried to use a popular package out there called "createUser" but that fails as well.
Has anyone had any luck with this when trying to make a moduler image with System Image Utility?
Message was edited by: NeedSomeAnswer

After configuring all the appropriate settings, I
push the "Create" button and it appears to start
working, prompts me for a location to save the actual
image itself, creates a folder with the default name
and then nothing happens.
ok here's the deal: i created a folder in my OSX server home directory labelled "images" and keep our multiple images there. although you CAN have your images on other drives or on the network, that would take a LOOOOOOOONG time to do the data transfer to the invisible netboot folder on your server. my advice: keep local copies of all images. save a ton of time for yourself, eh?
then, when it's time to use the system image suntility to load up an image, i go to that same location each time, call it up and have the app set to the prefs i want or need. i'm on 10.4.7 server and have had no problem using the software.
so try using images locally and then, if that doesn't work, upgrade to 10.4.7

1456: The remote management agent is unable

Hi
I have :
Server NW6.5 Sp5
Zenworks desktop 6.5 SP2
Client NT4 SP6 - Client novell 4.90 SP2
W2000 SP4 - Client novell 4.91 SP2 - Agent Zen SP2
WXP SP2 - Client novell 4.91 SP2 - Agent Zen SP2
The problem is that I can't connet with "remote management" some PC with XP;
The error in log file is:
#(464)# 10.16.27 02/16/06 Normal : Loading :
C:\Programmi\Novell\ZENworks\WMSchApi.dll
#(464)# 10.16.27 02/16/06 Critical : Workstation NOT yet authenticated...
#(464)# 10.16.27 02/16/06 Critical : ZENNDSUtil: initializeContext()
failed...
#(464)# 10.16.27 02/16/06 Normal : Reading workstation DN and tree name...
#(464)# 10.16.27 02/16/06 Normal : workstation DN -
PC01-WINXP-00:0B:CD:F8:F2:44., treename - TREE_GROUP
#(464)# 10.16.27 02/16/06 Normal : Loading :
C:\Programmi\Novell\ZENworks\WMSchApi.dll
#(464)# 10.16.27 02/16/06 Critical : Workstation NOT yet authenticated...
#(464)# 10.16.27 02/16/06 Critical : ZENNDSUtil: initializeContext()
failed...
#(464)# 10.16.27 02/16/06 Normal : Neither policy settings active. All
operations disabled.
#(464)# 10.16.27 02/16/06 Normal : ZENNDSUtil: Finished reading policies
#(464)# 10.16.27 02/16/06 Normal : ZENNDSUtil: Unloaded modules...
#(464)# 10.16.27 02/16/06 Normal : UnLoadZenAutilLibrary :Successfully
unloaded ZenAutil.dll
#(464)# 10.17.48 02/16/06 Normal : RMSessionFinished - Begin
If I check if the ogject workstation is authenticated on NDS, I not find the
connection.
I can connect only with che workstation that are list in connection.
Why some workstation connect to NDS ?
Thanks for help.
Gianluigi

Try deleting the workstation object and reboot the workstation (sometimes
a 2nd reboot is required).
> Hi
>
> Another information, if I use only the agent with out client novell, I
have
> no problem because the workstation is connect to NDS.
> If I want use client novell and Middle Tier is possible set Middle Tier
how
> default connection for remote manager ?
>
> Thank
>
> Gianluigi
>
> "Gianluigi Cortinovis" <[email protected]> ha scritto nel messaggio
> news:[email protected]...
> > No, I have disable windows firewall.
> >
> > Gianluigi
> >
> > "craig wilson" <[email protected]> ha scritto nel messaggio
> > news:[email protected]...
> >> Windows Firewall perhaps?
> >>
> >> --
> >> Craig Wilson
> >> Novell Product Support Forum Sysop
> >> Master CNE, MCSE 2003, CCNA
> >>
> >> Editor - http://www.ithowto.com
> >>
> >> (Seeking Full-Time Expert? Drop me a note :> )
> >>
> >>
> >> "Gianluigi Cortinovis" <[email protected]> wrote in message
> >> news:[email protected]...
> >>> Hi
> >>>
> >>> I have :
> >>> Server NW6.5 Sp5
> >>> Zenworks desktop 6.5 SP2
> >>>
> >>> Client NT4 SP6 - Client novell 4.90 SP2
> >>> W2000 SP4 - Client novell 4.91 SP2 - Agent Zen SP2
> >>> WXP SP2 - Client novell 4.91 SP2 - Agent Zen SP2
> >>>
> >>>
> >>> The problem is that I can't connet with "remote management" some PC
with
> >>> XP;
> >>> The error in log file is:
> >>>
> >>> #(464)# 10.16.27 02/16/06 Normal : Loading :
> >>> C:\Programmi\Novell\ZENworks\WMSchApi.dll
> >>> #(464)# 10.16.27 02/16/06 Critical : Workstation NOT yet
> >>> authenticated...
> >>> #(464)# 10.16.27 02/16/06 Critical : ZENNDSUtil: initializeContext
> >>> failed...
> >>> #(464)# 10.16.27 02/16/06 Normal : Reading workstation DN and tree
> >>> name...
> >>> #(464)# 10.16.27 02/16/06 Normal : workstation DN -
> >>> PC01-WINXP-00:0B:CD:F8:F2:44., treename - TREE_GROUP
> >>> #(464)# 10.16.27 02/16/06 Normal : Loading :
> >>> C:\Programmi\Novell\ZENworks\WMSchApi.dll
> >>> *******************************************
> >>> #(464)# 10.16.27 02/16/06 Critical : Workstation NOT yet
> >>> authenticated...
> >>> #(464)# 10.16.27 02/16/06 Critical : ZENNDSUtil: initializeContext
> >>> failed...
> >>> *******************************************
> >>> #(464)# 10.16.27 02/16/06 Normal : Neither policy settings active.
All
> >>> operations disabled.
> >>> #(464)# 10.16.27 02/16/06 Normal : ZENNDSUtil: Finished reading
policies
> >>> #(464)# 10.16.27 02/16/06 Normal : ZENNDSUtil: Unloaded modules...
> >>> #(464)# 10.16.27 02/16/06 Normal :
UnLoadZenAutilLibrary :Successfully
> >>> unloaded ZenAutil.dll
> >>> #(464)# 10.17.48 02/16/06 Normal : RMSessionFinished - Begin
> >>>
> >>>
> >>> If I check if the ogject workstation is authenticated on NDS, I not
find
> >>> the connection.
> >>>
> >>> I can connect only with che workstation that are list in connection.
> >>>
> >>> Why some workstation connect to NDS ?
> >>>
> >>> Thanks for help.
> >>>
> >>> Gianluigi
> >>>
> >>>
> >>
> >>
> >
> >
>
>

Changing the default file manager in XFCE

How would I go about using Nautilus as the default file manager in XFCE instead of Thunar? I know it can be started up with 'nautilus --no-desktop', but how do I make this the default when opening folders from the desktop, menus, etc..?
The main reason I want to do this is because Thunar doesn't seem to remember a folders last setting. For example, there are folders which I would like to permanently view as a list, sorted by date; but there are plenty of other folders where this is not suitable. Nautilus remembers settings for each folder, Thunar doesn't, and it gets annoying changing the view mode each time. Also network browsing is easier in Nautilus, and I also like the way it tells you how fast file transfers are going.
Thanks very much,

Well, it might be considered a dirty hack but it has worked for me in gnome before so it should also work in xfce. Just edit the thunar.desktop file in /usr/share/applications and replace the Exec=thunar to Exec=nautilus --no-desktop and save the file. Then any time thunar is launched, nautilus will be launched instead.
Otherwise, you can edit the menu with the menu editor and change the File manager command and do the same in the panel icon properties. Both methods will work.

Error while running Remote Manager for OIM11gR2

Hi,
I have 11gR2 Remote Manager configured in a Windows box on a different machine as OIM server. I am getting the below error while running the RM-
C:\RemoteManager\remote_manager>remotemanager.bat
C:\RemoteManager\remote_manager>set RM.ServiceName=RManager
C:\RemoteManager\remote_manager>set LIB_DIR=.\lib
C:\RemoteManager\remote_manager>set EXT_DIR=.\ext
C:\RemoteManager\remote_manager>set APPSERVER_TYPE=wls
C:\RemoteManager\remote_manager>set CLASSPATH=.;.\lib\xlAPI.jar;.\lib\xlVO.jar;.\lib\xlScheduler.jar;.\lib\xlRemoteManager.jar;.\lib\xerces.jar;.\lib\xlDataObjects.jar;.\lib\log4j-
1.2.8.jar;.\lib\xlUtils.jar;.\lib\xlLogger.jar;.\lib\xlCrypto.jar;.\lib\iam-platform-utils.jar;.\lib\oimclient.jar;.\ext\spring.jar;.\ext\commons-logging.jar;..\..\oracle_common\mo
dules\oracle.jrf_11.1.1\jrf-api.jar
C:\RemoteManager\remote_manager>"C:/Program Files/Java/jdk1.7.0/bin/java" -cp .;.\lib\xlAPI.jar;.\lib\xlVO.jar;.\lib\xlScheduler.jar;.\lib\xlRemoteManager.jar;.\lib\xerces.jar;.\li
b\xlDataObjects.jar;.\lib\log4j-1.2.8.jar;.\lib\xlUtils.jar;.\lib\xlLogger.jar;.\lib\xlCrypto.jar;.\lib\iam-platform-utils.jar;.\lib\oimclient.jar;.\ext\spring.jar;.\ext\commons-lo
gging.jar;..\..\oracle_common\modules\oracle.jrf_11.1.1\jrf-api.jar -Dlog4j.configuration=config\log.properties -DXL.HomeDir=C:\RemoteManager\remote_manager com.thortech.x
l.remotemanager.RemoteManager
Feb 9, 2013 2:00:54 AM com.thortech.util.logging.Logger error
SEVERE: Class/Method: ConfigurationClient/init encounter some problems: Unable to encrypt the value for: #text
Feb 9, 2013 2:00:55 AM com.thortech.util.logging.Logger error
SEVERE: Class/Method: ConfigurationClient/init encounter some problems: Unable to encrypt the value for: #text
Feb 9, 2013 2:00:55 AM com.thortech.util.logging.Logger error
SEVERE: Class/Method: ConfigurationClient/init encounter some problems: Unable to encrypt the value for: #text
Feb 9, 2013 2:00:55 AM com.thortech.util.logging.Logger error
SEVERE: Class/Method: ConfigurationClient/init encounter some problems: Unable to encrypt the value for: #text
Feb 9, 2013 2:00:55 AM com.thortech.util.logging.Logger error
SEVERE: Class/Method: ConfigurationClient/init encounter some problems: Unable to encrypt the value for: #text
Feb 9, 2013 2:00:55 AM com.thortech.util.logging.Logger error
SEVERE: Class/Method: ConfigurationClient/init encounter some problems: Unable to encrypt the value for: #text
Feb 9, 2013 2:00:55 AM com.thortech.util.logging.Logger error
SEVERE: Class/Method: ConfigurationClient/init encounter some problems: Unable to encrypt the value for: #text
Feb 9, 2013 2:00:55 AM com.thortech.util.logging.Logger error
SEVERE: Class/Method: ConfigurationClient/init encounter some problems: Unable to encrypt the value for: #text
Feb 9, 2013 2:00:55 AM com.thortech.util.logging.Logger error
SEVERE: Class/Method: ConfigurationClient/init encounter some problems: Unable to encrypt the value for: #text
Feb 9, 2013 2:00:55 AM com.thortech.util.logging.Logger error
SEVERE: Class/Method: ConfigurationClient/init encounter some problems: Unable to encrypt the value for: #text
Feb 9, 2013 2:00:55 AM com.thortech.util.logging.Logger info
INFO: Class/Method: RMIClientSocketFactory/static: sslEnabled : trueSSLContextAlgorithm : TLSKeyManagerFactory : @keymgrfactoryKeyStore : C:\RemoteManager\remote_manager\config\def
ault-keystore.jksKeyStoreType : JKSTrustStore : default-keystore.jks
Feb 9, 2013 2:00:55 AM com.thortech.util.logging.Logger info
INFO: Class/Method: RMISSLServerSocketFactory/createServerSocket Remote Manager server socket port is 12346
Exception in thread "main" java.lang.NullPointerException
at com.thortech.xl.remotemanager.RMISSLServerSocketFactory.createServerSocket(RMISSLServerSocketFactory.java:173)
at sun.rmi.transport.tcp.TCPEndpoint.newServerSocket(TCPEndpoint.java:667)
at sun.rmi.transport.tcp.TCPTransport.listen(TCPTransport.java:317)
at sun.rmi.transport.tcp.TCPTransport.exportObject(TCPTransport.java:236)
at sun.rmi.transport.tcp.TCPEndpoint.exportObject(TCPEndpoint.java:411)
at sun.rmi.transport.LiveRef.exportObject(LiveRef.java:147)
at sun.rmi.server.UnicastServerRef.exportObject(UnicastServerRef.java:207)
at java.rmi.server.UnicastRemoteObject.exportObject(UnicastRemoteObject.java:310)
at java.rmi.server.UnicastRemoteObject.exportObject(UnicastRemoteObject.java:273)
at java.rmi.server.UnicastRemoteObject.<init>(UnicastRemoteObject.java:172)
at com.thortech.xl.remotemanager.RemoteManager.<init>(RemoteManager.java:80)
at com.thortech.xl.remotemanager.RemoteManager.main(RemoteManager.java:449)
C:\RemoteManager\remote_manager>
Any suggestions?

Hi,
I have 11gR2 Remote Manager configured in a Windows box on a different machine as OIM server. I am getting the below error while running the RM-
C:\RemoteManager\remote_manager>remotemanager.bat
C:\RemoteManager\remote_manager>set RM.ServiceName=RManager
C:\RemoteManager\remote_manager>set LIB_DIR=.\lib
C:\RemoteManager\remote_manager>set EXT_DIR=.\ext
C:\RemoteManager\remote_manager>set APPSERVER_TYPE=wls
C:\RemoteManager\remote_manager>set CLASSPATH=.;.\lib\xlAPI.jar;.\lib\xlVO.jar;.\lib\xlScheduler.jar;.\lib\xlRemoteManager.jar;.\lib\xerces.jar;.\lib\xlDataObjects.jar;.\lib\log4j-
1.2.8.jar;.\lib\xlUtils.jar;.\lib\xlLogger.jar;.\lib\xlCrypto.jar;.\lib\iam-platform-utils.jar;.\lib\oimclient.jar;.\ext\spring.jar;.\ext\commons-logging.jar;..\..\oracle_common\mo
dules\oracle.jrf_11.1.1\jrf-api.jar
C:\RemoteManager\remote_manager>"C:/Program Files/Java/jdk1.7.0/bin/java" -cp .;.\lib\xlAPI.jar;.\lib\xlVO.jar;.\lib\xlScheduler.jar;.\lib\xlRemoteManager.jar;.\lib\xerces.jar;.\li
b\xlDataObjects.jar;.\lib\log4j-1.2.8.jar;.\lib\xlUtils.jar;.\lib\xlLogger.jar;.\lib\xlCrypto.jar;.\lib\iam-platform-utils.jar;.\lib\oimclient.jar;.\ext\spring.jar;.\ext\commons-lo
gging.jar;..\..\oracle_common\modules\oracle.jrf_11.1.1\jrf-api.jar -Dlog4j.configuration=config\log.properties -DXL.HomeDir=C:\RemoteManager\remote_manager com.thortech.x
l.remotemanager.RemoteManager
Feb 9, 2013 2:00:54 AM com.thortech.util.logging.Logger error
SEVERE: Class/Method: ConfigurationClient/init encounter some problems: Unable to encrypt the value for: #text
Feb 9, 2013 2:00:55 AM com.thortech.util.logging.Logger error
SEVERE: Class/Method: ConfigurationClient/init encounter some problems: Unable to encrypt the value for: #text
Feb 9, 2013 2:00:55 AM com.thortech.util.logging.Logger error
SEVERE: Class/Method: ConfigurationClient/init encounter some problems: Unable to encrypt the value for: #text
Feb 9, 2013 2:00:55 AM com.thortech.util.logging.Logger error
SEVERE: Class/Method: ConfigurationClient/init encounter some problems: Unable to encrypt the value for: #text
Feb 9, 2013 2:00:55 AM com.thortech.util.logging.Logger error
SEVERE: Class/Method: ConfigurationClient/init encounter some problems: Unable to encrypt the value for: #text
Feb 9, 2013 2:00:55 AM com.thortech.util.logging.Logger error
SEVERE: Class/Method: ConfigurationClient/init encounter some problems: Unable to encrypt the value for: #text
Feb 9, 2013 2:00:55 AM com.thortech.util.logging.Logger error
SEVERE: Class/Method: ConfigurationClient/init encounter some problems: Unable to encrypt the value for: #text
Feb 9, 2013 2:00:55 AM com.thortech.util.logging.Logger error
SEVERE: Class/Method: ConfigurationClient/init encounter some problems: Unable to encrypt the value for: #text
Feb 9, 2013 2:00:55 AM com.thortech.util.logging.Logger error
SEVERE: Class/Method: ConfigurationClient/init encounter some problems: Unable to encrypt the value for: #text
Feb 9, 2013 2:00:55 AM com.thortech.util.logging.Logger error
SEVERE: Class/Method: ConfigurationClient/init encounter some problems: Unable to encrypt the value for: #text
Feb 9, 2013 2:00:55 AM com.thortech.util.logging.Logger info
INFO: Class/Method: RMIClientSocketFactory/static: sslEnabled : trueSSLContextAlgorithm : TLSKeyManagerFactory : @keymgrfactoryKeyStore : C:\RemoteManager\remote_manager\config\def
ault-keystore.jksKeyStoreType : JKSTrustStore : default-keystore.jks
Feb 9, 2013 2:00:55 AM com.thortech.util.logging.Logger info
INFO: Class/Method: RMISSLServerSocketFactory/createServerSocket Remote Manager server socket port is 12346
Exception in thread "main" java.lang.NullPointerException
at com.thortech.xl.remotemanager.RMISSLServerSocketFactory.createServerSocket(RMISSLServerSocketFactory.java:173)
at sun.rmi.transport.tcp.TCPEndpoint.newServerSocket(TCPEndpoint.java:667)
at sun.rmi.transport.tcp.TCPTransport.listen(TCPTransport.java:317)
at sun.rmi.transport.tcp.TCPTransport.exportObject(TCPTransport.java:236)
at sun.rmi.transport.tcp.TCPEndpoint.exportObject(TCPEndpoint.java:411)
at sun.rmi.transport.LiveRef.exportObject(LiveRef.java:147)
at sun.rmi.server.UnicastServerRef.exportObject(UnicastServerRef.java:207)
at java.rmi.server.UnicastRemoteObject.exportObject(UnicastRemoteObject.java:310)
at java.rmi.server.UnicastRemoteObject.exportObject(UnicastRemoteObject.java:273)
at java.rmi.server.UnicastRemoteObject.<init>(UnicastRemoteObject.java:172)
at com.thortech.xl.remotemanager.RemoteManager.<init>(RemoteManager.java:80)
at com.thortech.xl.remotemanager.RemoteManager.main(RemoteManager.java:449)
C:\RemoteManager\remote_manager>
Any suggestions?

Default Remote Management Settings

Similar Messages

Maybe you are looking for