Delay after Windows XP loads

Ok guys I fell alittle better about this board now (although I have 12 days left on my RMA #).  I have the MSI 875P Neo-FIS2R with a Seagate 120GB 8MB cache SATA Hard dive installed on the South Bridge.  When Windows XP Professional is finished loading and I am at the desktop I am unable to access my DSL connection to the internet, I click on the icon to connect and I have about a minute and a half wait before it connects.  I am also unable to access the device manager or the monitor refresh rates.  Now if I wait the minute and a half the hard drive will run for a few seconds and then I am able to click on the DSL connection and it almost instantly connects.  Same with device manager and the refresh rates.  I am sure there are other items with delay as well.  Now I do not have this problem start until I update to service pack one (I have reinstalled windows so many time due to my video card troubles) Any suggestions as to what is actually causing the delay?

Hi to all,
Ok, delays caused are very general... there are a few reasons to this, so I post them here and try out to see if that solved your delaying probs...
1. Too many background running programs during bootup.
2. Anti-Virus doing screenscan during startup.
3. Settings of P-ATA and S-ATA in BIOS disabled.
4. Cached shadow enabled.
5. Low PSU wattage for +3V,+5V rails, if possible +12V.
6. CPU usuage high due to system tray programs during startup.
For AGP card not showing 8x:
1. Try setting AGP Capabilities to "Auto".
2. Set AGP Aperture to 128MB or 256MB.
3. Update to latest drivers(do clean un-installation 1st).
4. Disable SBA(SideBand Addressing).
Hope my info and directions helps...
All the Best... :D!!!

Similar Messages

  • T400 Display works at start up but Dark after Windows 7 loads --- Video port works

    My T400  display works  at BIOS startup but goes black was soon as Windows 7 starts to load..  Video out put  works  and I can see an  UN Backlit   image on the display.    Is there some sort  back light controller /driver that may be broken.
    Solved!
    Go to Solution.

    Sorry, should have been more specific 
    I don't mean you should switch to Linux, just run it out of a live CD or USB Stick so that we can rule out a hardware failure. If it works in Linux ok for a while, it can mean that you have some sort of software problem.
    If your T400 screen goes dark with Linux as well, you may be facing a hardware problem, which could be a defective backlight, a defective inverter (or LED card) or a defective cable.
    Can you post here the model type of your T400? It's a 7 digit code that can be found in a black and white sticker at the bottom of the laptop.
    /L40SX/240/240X/2*340CSE/360PE/365XD/380D/380E/380XD/380Z/390/560E/560X/2*570/2*600/600E/750Cs/755C/760CD/760EL/760XD/770E/A20p/A22p
    A31/i1600/G40/R50p/R61i/S30/SL510/2*T22/4*T4x/11*T6x/6*T4x0x/6*T5x0/3*W5x0/W700/3*X2x/4*X3x/3*X4x/5*X6x/3*X6xT/10*X2xx/2*X200T/4*X30x/Z60m/3*Z61x
    Comunidad en Español  English Community  Deutsche Community   Русскоязычное Сообщество

  • Windows 7 -Delay after right click and installation query

    Hi,
    I have freshly clean installed Windows 7 home premium x64 in my HP laptop which was previously running the x86 version of the same factory installed OS.I have performed a usb install.Now,I have two queries-
    1.During the installation,when the machine rebooted,to complete the installation process,it gave the option of 'Continue with win 7-EMS ENABLED'-and I went ahead with it and completed the process.I want to know whether this EMS thing is normal or not?
    2.There is a slight delay after the right click in the desktop-how can it be resolved?
    Looking forward for your valuable opinions regarding this

    Hi,
    First please know that EMS allows users to control particular components of a server remotely, even when the server is not connected to the network or to other standard remote-administration tools. In Windows Vista and later, use BCDEdit /emssettings command
    and its parameters to establish EMS settings for all boot entries. Then, use the BCDEdit /ems command to enable EMS for a particular boot entry.
    It's ok to get EMS enabled.
    For your second question, it seems a performance issue.
    Please first let me know except the system default context on the right click menu, if there is any 3rd part context menu or extension. if so, please use shellexview to remove them:
    1. Download ShellExView v1.41 from the following link
    http://www.nirsoft.net/utils/shexview.zip 
    Please Note: The third-party product discussed here is manufactured by a company that is independent of Microsoft. We make no warranty, implied or otherwise, regarding this product's performance or reliability.
    2.  Extract "shexview.zip" file and open shexview.exe. It will scan the registry for all the shell extensions.
    3. Select all the non-Microsoft extensions in pink by press "Ctrl" in the keyboard.
    4. Click the "Disable Selected Items" on the toolbar and click Yes.
    5. Restart your computer and check if the issue is resolved.
    If there is no such context menu, please run performance troubleshooting under Control Panel\All Control Panel Items\Troubleshooting\All Categories.
    Also, help to test the issue in Clean boot mode.
    How to perform a clean boot
    http://support.microsoft.com/kb/929135
    If the issue doesn’t appear, you can determine which one can be the cause by using dichotomy in MSconfig. Checking on half of Non-Microsoft service and restart, determining which half of the services cause the issue and repeating to check half of the problematic
    half services.
    If the issue still persists, please check if there is any related error or warning in event logs, post back for our further research.
    Kate Li
    TechNet Community Support

  • Cannot load my personal desktop after windows updates

    Since a windows update when I switch on I get a temporary desktop, cannot access my personal desktop unless I do a restore to an earlier date.  Tells me I cannot access my files and to log off and on again, no use.  Do get the message temporary desktop see your administrator etc.  Any help PLEASE.

    Hi,
    You could try the following.
    Shut down the notebook.  Tap away at f8 as you start the notebook to enter Windows Recovery Console.  Use the arrow keys to select Safe Mode and hit enter.  If windows will load in this mode, from the Start Menu, click All Programs, click Accessories, click System Tools and launch System Restore.  Pick a restore point at least 24 hours before the log-on issue and then proceed with the restore process.  When complete, Windows will reboot as normal so check if you can now log in correctly.
    Another option if the above does not help is as follows.
    Shut down the notebook.  Tap away at f8 as you start the notebook to enter Windows Recovery Console.  Use the arrow keys to select 'Start Using Last Known Good Configuration' and hit enter.
    Regards,
    DP-K
    ****Click the White thumb to say thanks****
    ****Please mark Accept As Solution if it solves your problem****
    ****I don't work for HP****
    Microsoft MVP - Windows Experience

  • Windows cannot load the user's profile but has logged you on with the default profile for the system.

    My Windows 7  crashed a couple days ago after a windows update, I got this message.
    Windows cannot find the local profile and is logging you on with a temporary profile. Changes you make to this profile will be lost when you log off.
    I restarted the machine and got this message
    Windows was unable to load the registry. This problem is often caused by insufficient memory or insufficient security rights.
    DETAIL - The process cannot access the file because it is being used by another process. for C:\Users\TEMP\ntuser.dat
    I checked the event Log I found these .
    Windows cannot load the user's profile but has logged you on with the default profile for the system.
    DETAIL - Only part of a ReadProcessMemory or WriteProcessMemory request was completed.
    Windows has backed up this user profile. Windows will automatically try to use the backup profile the next time this user logs on.
    Windows cannot load the locally stored profile. Possible causes of this error include insufficient security rights or a corrupt local profile.
     DETAIL - The process cannot access the file because it is being used by another process.
    This is the first error in the event viewer after a successful logon
    The description for Event ID 34 from source ccSvcHst cannot be found. Either the component that raises this event is not installed on your local computer or the installation is corrupted. You can install or repair the component on the local computer.
     If the event originated on another computer, the display information had to be saved with the event.
    ccSetMgr
    Windows cannot load the user's profile but has logged you on with the default profile for the system.
    DETAIL - Access is denied.
    Looking at the Logs all I can tell is that after the Desktop Window Manager started if caused this error.
    The winlogon notification subscriber <SessionEnv> was unavailable to handle a notification event.
    then this one
    The Desktop Window Manager has exited with code (0x40010004)
    Then this before it shutdown.
    The User Profile Service has stopped.
    I started up the PC and the first message I got was
    How can I get access to my user profile? do I need to createa new Administrator account? Please help
    The EventSystem sub system is suppressing duplicate event log entries for a duration of 86400 seconds. The suppression timeout can be controlled by a REG_DWORD value named SuppressDuplicateDuration under the following registry key: HKLM\Software\Microsoft\EventSystem\EventLog.

    hi do the following
    1. In Search programs and files (Windows 7) area, type in regedit, and press Enter.
    2. If prompted click yes,
    3.  expand the following HKEY_LOCAL_MACHINE\SOFTWARE\Microsoft\Windows NT\CurrentVersion\ProfileList
    4. click the sid that related to your admin profile (if you not sure, click each sid and in turn look to the right hand side of registry editor it will show who that sid is related to one of the registry files should hae in description localhost\admin or
    something similair)
    5. right click the sid and press delete.
    6. restart your machine and log back on with the admin account, this will then rebuild the admin profile... dont worry when it loads and none of your personal settings are saved or files or folders... go to c:\users
    in here you will see two folders for the admin account, one will be just admin and the other most likely admin.localhost
    i cant remember which one is which but just check both, one will still have all your files and folders in it.
    i suggest making a backup of your data before doing this incase something does go wrong, but ive had this happen many times in a domain enviorment and has worked for me everytime.

  • Skype Failed to install error 1603 after windows r...

    Hey everyone! Thanks for any help in advanced.
    Honestly after losing access to an old account and making a new account I've still been a long time fan of skype and love free 1 on 1 video calls. I'm really hoping this is an easy fix because honestly I've been looking at the skype community forums for the last hour and havn't been able to find a fix.
    About 2 and a half hours ago I reduced the size of my only partiton on my 500 GB harddrive as much as I could. After doing this I reinstalled windows on the new 200ish GB partition. After installing and loading windows I coppied skype, smite, and steam from D:\Program Files to C:\Program Files (x86) and attempted to run skype. Skype opened and I signed in as usual but skype was having a really high CPU usage and kept reading/writing to some statistics.db file at several GB/s (Total IO was like 1.8GB/s, mostly write I think). The 13% cpu usage, although concerning as abnormally high, didnt really bog down performance too much. This high disk usage was really driving my mad as when it peaked my computer would almost stop responding and skype.exe would stop responding (although it resumed eventually). Skype in this state was unusable as any time the window was focused it almost crashed.
    After this I decided to reinstall skype instead of using the backup I had. I went to uninstall skype and found that it didnt show up on the list to "uninstall a program" so I tried following as many steps I could at https://support.skype.com/en/faq/FA10634/how-can-i-completely-uninstall-and-then-reinstall-skype-for...
    I've also followed all the steps here except for installing an earlier version of skype as I'm not sure what version to use. http://community.skype.com/t5/Windows-desktop-client/Skype-Problems-Troubleshooting/td-p/52260
    I force ended skype.exe then made backups of my skype user and pictures folders. I skipped step 3 since it wasn't in the list. I then did steps 4-6. While doing this I noticed it said there may be "up to 50" references to skype in the registry but I noticed there were a lot more. I'm not exactly sure how many there were but I counted up to 40 and when I noticed I was only half way through the registry I started spamming "delete" key "enter" (to confirm deletion) as fast as I could.  I'd say there were at least 70 skypes in the registry. I'm not sure if this registry includes things from my other installation of windows or if it got **bleep**ed up because of they way I tried to install skype.
    After doing all this with my registry I rechecked to make sure the skype program files and skype app data folders were deleted and then tried to reinstall skype. Downloading from http://www.skype.com/en/download-skype/skype-for-computer/ I tried to reinstall it and all I did was unchecked "run skype when windows starts" hit next unchecked the bing and skype click to call stuff, hit next. After it said installing for a while it said installation failed error 1603.
    I tried following advice of several posts on the forums and other sites, including going through the registry again, using Microsofts FixIt for install/uninstalls, and trying to install skype from another administrator account. After looking at several posts, trying all these fixes, and looking into it myself I'm really not sure what to do.
    I've looked at all of the following posts and tried all the fixes I saw.
    http://community.skype.com/t5/Windows-desktop-client/Skype-Problems-Troubleshooting/td-p/52260
    https://support.skype.com/en/faq/FA10634/how-can-i-completely-uninstall-and-then-reinstall-skype-for...
    http://community.skype.com/t5/Windows-desktop-client/Skype-using-100-of-my-disk-and-then-crashing-Wi...
    http://community.skype.com/t5/Windows-desktop-client/Error-code-1603-installing-Skype-5-5-on-Windows...
    http://community.skype.com/t5/The-Skype-Lounge/TheUberOverLord-Install-Issues-Check/m-p/156736/highl...
    http://support.microsoft.com/mats/Program_Install_and_Uninstall/
    http://www.msigeek.com/715/how-to-troubleshoot-the-error-1603-fatal-error-during-installation (This page gave me an "Error establishing database connection" page)
    Not really sure what else to say or do, I've never really had to debug any programs or windows features before, and the only time I ever messed with the registry was a few windows installs before when I had to delete several instances of a self-reinstalling virus on my computer that spammed processes and lagged my computer.
    Edit: After seeing this link I tried rerunning Microsoft's FixIt Install/Uninstall with the program ID from the folder name at %programdata%\Skype. I tried doing this and installing Skype from SkypeSetup_6.1.0.129.msi. Installation failed with some failed to read file totally forgot what it was. I then tried using the standard InstallSkypeFull.exe and it gave an actual error this time instead of the apparently "generic" error 1603 (see attached picture) After this installation failed I tried reinstalling from the 6.1.0.129.msi and it didn't say it failed. I'm about to try and open it.
    Anddd opening Skype failed with the error message in the attached skype2 picture. I'm just going to close everything related to that except for this post and I'm going to close all my installers and debug stuff I have open and just wait for a reply. Currently I believe the system thinks skype is installed but I can't open it.
    Solved!
    Go to Solution.
    Attachments:
    skype.png ‏392 KB
    skype2.png ‏232 KB

    I'm afraid that after all the manipulations your system is so messed up that a regular Skype installation is no longer possible.
    Try this:
    Download but not run this msi-installer for Skype 6.9.0.106 version:
    http://download.skype.com/msi/SkypeSetup_6.9.0.106.msi
    Create a folder on your computer where you want Skype application to be located. This folder can also be C:\Program Files (x86)\Skype\Phone\, but any other location will work too.
    Now using the procedure described here:
    http://community.skype.com/t5/Windows-desktop-client/How-to-update-Skype-without-using-any-Skype-ins...
    extract Skype.exe file from the SkypeSetup_6.9.0.106.msi file and copy this Skype.exe file to the selected installation folder.
    Right click on the Skype.exe file and select: Send to – Desktop (create shortcut). You will have to start Skype using this new shortcut.
    P.S. There is a new link to the latest Lessmsi program:
    https://code.google.com/p/lessmsi/downloads/list

  • App store doesn't work (freezes, "Main window NIB load started 2min"...)

    My log:
    -------------------------------------------------------- Begin --
                 System Version 10.9.2 (Build 13C64) "App Store" Version 1.3 (201.4)
    Mar 23 21:13:44 Lap App Store[98261]: FRStoreViewController: Using process-per-webview model for identifier primary
    Mar 23 21:14:14 Lap App Store[98261]: CKClientDispatch: Timeout occurred invoking selector storeFrontID on class StoreClientController with object (null) (four times)
    Mar 23 21:15:44 Lap App Store[98261]: APAppDelegate: Main window NIB load started 120.2284(two minutes???) seconds after launch
    Mar 23 21:15:45 Lap App Store[98261]: FRStoreViewController: Store state changed to splash (loading)
    Mar 23 21:16:15 Lap App Store[98261]: CKClientDispatch: Timeout occurred invoking selector isValidWithInfo: on class BagController with object {
                  bagType = 1;
    Mar 23 21:16:45 Lap.local App Store[98261]: CKClientDispatch: Timeout occurred invoking selector primaryAccount on class AccountStore with object (null)
    I tried to delete the temporary files directory and the caches, change the permissions, run AppStore application with root previlegies, delete preferences, reboot system, etc. Some problem
    Ther're 2 user in system. This problem only with my account. Under other user - all is fine.
    I do not want to reinstall the system or work under other account.

    Hi, thanks again.
    I reinstalled Lion (using Recovery), but the problem remains. Even worse, Apple Software Update didn't work any more. As soon as I selected something for installation (e.g. iTunes), the progress bar would show but then it used to freeze forever (internet connection was fine). I tried several times after reboot.
    The I tried a hard shutdown (holding the power key pressed), and after that, the app store was working (very slowly) and i could also install the software updates.
    However, after a normal reboot, the app store didn't work any more.
    I repeated this twice with the same result: the app store works after a hard shutdown, but not after a normal shutdown+reboot.
    Any suggestions?

  • Problems with Twist Before and after Windows 8.1 Upgrade

    I'm not sure if this is a problem on Windows' end or Lenovo's, but here it goes. Problems AFTER Windows 8.1 update:
    1.) When I close the computer, even though the power management settings are set to put the computer to sleep, it only goes to sleep about 50% of the time. If I don't catch it, that means the battery will drain completely while I'm under the impression it's sleeping. The kicker is, even if I do catch it, I can't get the computer to turn back on. The screen stays black until I hold the power button down and force the computer to turn off and restart it.
    2.) iTunes will not open. I don't get any numbered error message, just a message that it failed. I've tried running iTunes in compatibility mode, and I've uninstalled and reinstalled it, to no avail.
    Problems BEFORE:
    1.) When I first got the computer, it was super quiet. Now the fan is pretty loud and buzzy. It seems that it may even be brushing something, because if I push the bottom up ever so gently, the sound goes down by half. Not a huge issue, but especially noticeable when I'm in tablet mode.
    I know that at least the last one isn't a unique problem. I can kind of live with that, but the first two are really driving me nuts.

    I made the mistake of loading W8.1 on my Twist without realizing how raw and bug prone the preview really could be.  The backout would require reloading a lot of applications, and this is not my primary PC, so I am toughing it out.  Saw updates load.  Current build is 9431.
    I am currently uninstalling software and updates until I get a stable environment again.  Here is some general feedback...
    I have not had an issue with the Lenovo System Update running.  I suggest you do ONE update at a time.
    50% of the shutdown/reboots fail and I need to hard power off with the power button
    Manually loading the latest Intel video driver software caused MAJOR problems.  Many programs simply did not run and everything was locking up.  Backing that out motivated me to remove other stuff.  The Lenovo System Update is offering to install a driver which I will attempt after all other firmware and drivers are updated.
    I use the Classic Shell v3.6.8 on the desktop.  I thought the 8.1 would return the start button, but I assume that Classic Shell is overriding that.
    Like others, I have had trouble getting the Juniper VPN software to load and work.  Trying to back everything out, but the virtual juniper nic is still showing up in the device manager.
    I am usually a reader of discussion forums and not a poster.  I will do my best to post my resolutions as well as issues.

  • Installing windows vista load driver problem

    I am trying to load Windows Vista Ultimate SP1 32. I follow the bootcamp assistant instructions. I select "Disk 0 Partition 3 BOOTCAMP" as instructed but the "Next" button will not function. I can tab or select between drives, Refresh and Load Driver but cannot get to Next. The Bootcamp instructions say to load drivers after Windows is installed but I can't get Windows installed?? What am I doing wrong?
    Thanks,
    Bill

    Found my own problem. Had to click on drive options advanced and format. That still didn't work because the disk was too small. Increased disk size and successfully completed install.

  • Windows Server 2012 R2 - ADFS/Windows Network Load Balancing Converging Issue

    Hello,
    My name is Brandon. We have started upgrading our servers to Windows Server 2012 R2. We have some powerful servers for running ESXI 5.5 as the OS with the Guest Operating Systems as Windows Server 2012 R2. As far of our migrations/upgrades we have configured
    ADFS 2012 R2 into a Server Farm with Windows Network Load Balancing to add redundancy in the event a server goes down.
    I have been having issues with a Node with the Cluster getting stuck in the Status of Converging. The only way I have been able to get it back up is to restart the virtual server completely and it is temporary. When I first configure the Cluster the two
    virtual servers get added to the Node with no problems and fully converge. However, after some time a node will end up in Converging and this takes Authentication for ADFS down as the nodes can not be contacted over Port 443.
    Error: Host: server.domain.com Unable to connect to "server name"
    System
    Provider
    [ Name]
    Microsoft-Windows-NLB
    [ Guid]
    {F22AF71F-C4C3-425D-9653-B2F47B85DD30}
    EventID
    21
    I have tried using 1 & 2 Virtual NICs on the machines and still end up with communication issues. Could someone assist me with why I am having this issue? This is not an issue with a firewall. If it was a firewall it would never communicate the first
    time. Has anyone had experience with a similar configuration and how were you able to make it work?
    Below is my configuration.
    Static ARP Entry for Cluster IP Address has been added to our Layer 3 switch.
    Physical Server 1:
    ESXI 5.5 HOST
    1 NIC CONNECTED (shared with virtual guest)
    IP ADDRESS: 192.168.0.5
    SUBNET: 255.255.255.0
    DGW: 192.168.0.1
    Virtual Server 1 (Guest OS)
    Physical Server 2:
    ESXI 5.5 HOST
    1 NIC CONNECTED (shared with virtual guest)
    IP ADDRESS: 192.168.0.6
    SUBNET: 255.255.255.0
    DGW: 192.168.0.1
    Virtual Server 2 (Guest OS)
    Virtual Servers
    Virtual Server 1
    MS SERVER 2012 R2 (VIRTUAL)
    NLB NODE 2 
    VIRTUAL NETWORK ADAPTERS
     VNIC1 IP ADDRESS 192.168.0.10
    SUBNET: 255.255.255.0
    DGW: 192.168.0.1
     VNIC 2 (NLB)
    IP ADDRESS: 192.168.0.11
    SUBNET: 255.255.255.0
    Virtual Server 2
    MS SERVER 2012 R2 (VIRTUAL)
    NLB NODE 2
    VIRTUAL NETWORK ADAPTERS
     VNIC1
    IP ADDRESS 192.168.0.20
    SUBNET: 255.255.255.0
    DGW: 192.168.0.1
     VNIC 2 (NLB)
    IP ADDRESS: 192.168.0.21
    SUBNET: 255.255.255.0
    Cluster Configuration/Properties
    CLUSTER PROPERTIES CLUSTER IP: 192.168.0.30
    CLUSTER SUBNET: 255.255.255.0
    FULL INTERNET NAME: FS.DOMAIN.COM
    CLUSTER OPERATION MODE: MULTICAST
    PORT RULES:
    CLUSTER IP ADDRESS
    START
    END
    PROTOCAL
    MODE
    PRIORITY
    LOAD
    AFFINITY
    ALL
    80
    80
    BOTH
    MULTIPLE
    EQUAL
    NONE
    ALL
    443
    443
    BOTH
    MULTIPLE
    EQUAL
    NONE
    CLUSTER NODES:
    1.) SERVER1.DOMAIN.COM
    a. IP: 192.168.0.11
    2.) SERVER2.DOMAIN.COM
    a. IP: 192.168.0.21

    Hi,
    According to your description, my understanding is that：2 ESXI 5.5 physical devices (192.168.0.5 and 192.168.0.6), each of them has a virtual WS 2012 R2(192.168.0.10 and 192.168.0.20). Cluster the 2 virtual servers successfully, but they corrupt with event
    ID 21, and a restart of virtual device will resolve this problem temporarily.
    Event ID 21 means that NLB failed to converge due to inconsistencies in the port rules between this host and cluster host. This will occur if the number of port rules or the type of port rules are different between hosts.
    Ensure that all NLB hosts have identical port rules. Detailed steps you may reference:
    Event ID 21 — NLB Port Rules Configuration
    https://technet.microsoft.com/en-us/library/dd364034%28v=ws.10%29.aspx?f=255&MSPPError=-2147217396
    Best Regards,
    Eve Wang
    Please remember to mark the replies as answers if they help and unmark them if they provide no help. If you have feedback for TechNet Support, contact
    [email protected]

  • Windows Server 2012 R2 - Windows Network Load Balancing Converging Issue

    Hello,
    My name is Brandon. We have started upgrading our servers to Windows Server 2012 R2. We have some powerful servers for running ESXI 5.5 as the OS with the Guest Operating Systems as Windows Server 2012 R2. As far of our migrations/upgrades we have configured
    ADFS 2012 R2 into a Server Farm with Windows Network Load Balancing to add redundancy in the event a server goes down.
    I have been having issues with a Node with the Cluster getting stuck in the Status of Converging. The only way I have been able to get it back up is to restart the virtual server completely and it is temporary. When I first configure the Cluster the two
    virtual servers get added to the Node with no problems and fully converge. However, after some time a node will end up in Converging and this takes Authentication for ADFS down as the nodes can not be contacted over Port 443.
    Error: Host: server.domain.com Unable to connect to "server name"
    System
    Provider
    Name]
    Microsoft-Windows-NLB
    Guid]
    {F22AF71F-C4C3-425D-9653-B2F47B85DD30}
    EventID
    21
    I have tried using 1 & 2 Virtual NICs on the machines and still receive this error even if only 1 VNIC is assigned to the virtual machine. Could someone assist me with why I am having this issue? Has anyone had experience with a similar configuration
    and how were you able to make it work?
    Below is my configuration.
    Static ARP Entry for Cluster IP Address has been added to our Layer 3 switch.
    Physical Server 1:
    ESXI 5.5 HOST
    1 NIC CONNECTED (shared with virtual guest)
    IP ADDRESS: 192.168.0.5
    SUBNET: 255.255.255.0
    DGW: 192.168.0.1
    Virtual Server 1
    Physical Server 2:
    ESXI 5.5 HOST
    1 NIC CONNECTED (shared with virtual guest)
    IP ADDRESS: 192.168.0.6
    SUBNET: 255.255.255.0
    DGW: 192.168.0.1
    Virtual Server 2
    Virtual Servers
    Virtual Server 1
    MS SERVER 2012 R2 (VIRTUAL)
    NLB NODE
    2 – VIRTUAL NETWORK ADAPTERS
     VNIC1
    IP ADDRESS 192.168.0.10
    SUBNET: 255.255.255.0
    DGW: 192.168.0.1
     VNIC 2 (NLB)
    IP ADDRESS: 192.168.0.11
    SUBNET: 255.255.255.0
    Virtual Server 2
    MS SERVER 2012 R2 (VIRTUAL)
    NLB NODE
    2 – VIRTUAL NETWORK ADAPTERS
     VNIC1
    IP ADDRESS 192.168.0.20
    SUBNET: 255.255.255.0
    DGW: 192.168.0.1
     VNIC 2 (NLB)
    IP ADDRESS: 192.168.0.21
    SUBNET: 255.255.255.0
    Cluster Configuration/Properties
    CLUSTER PROPERTIES
    CLUSTER IP: 192.168.0.30
    CLUSTER SUBNET: 255.255.255.0
    FULL INTERNET NAME: FS.DOMAIN.COM
    CLUSTER OPERATION MODE: MULTICAST
    PORT RULES:
    CLUSTER IP ADDRESS  START END  PROTOCAL MODE   PRIORITY LOAD  AFFINITY
    ALL    80 80 BOTH  MULTIPLE  ..  EQUAL  NONE
    ALL    443 443 BOTH  MULTIPLE  ..  EQUAL  NONE
    CLUSTER NODES:
    1.) SERVER1.DOMAIN.COM
    a. IP: 192.168.0.11
    2.) SERVER2.DOMAIN.COM
    a. IP: 192.168.0.21

    Thank you for your response. It took me a while to figure it out, but the whole issue was related to the type of Virtual Network Adapter I was selecting.
    I changed the network adapter from E1000 to VMXNET 3 and have not had a single error in the event logs or Windows NLB.
    I read somewhere that VMXNET 3 is preferred for Windows Server 2012 R2.
    https://communities.vmware.com/thread/433792
    Leyuka       May 23, 2013 6:14 AM
    "Just a help for everyone with this problem :
    After 10 days of research for our virtual datacenter behind a vcloud as iias ,  i found a solution .
    I only run windows 2012 server .
    Install vmware tools , remove e1000 network card after a vm stop, add a card same vswitch etc BUT with a vmxnet3 TYPE . DONT USE DEFAULT CARD
    Start and enjoy this solution . E1000 and E1000e are just unstable in windows8 / windows 2012 , the network card reset randomly with or without heavy IO. No log in windows , and as a vcloud user i don"t have esxi logs (damn i don't like cloud) and provider
    don"t know why ..."

  • Host Unreachable intermittently within a Windows Network Load Balancing Cluster

    Hi,
    We have 2 Windows 2008 R2 servers running multiple IIS web sites and load balanced across Windows Network Load Balancer in unicast mode. Although there are two interfaces in each server, only 1 interface in each server participates in load balancing and
    other interface is used for a different backup LAN. The problem I am going to mention was not seen within the NLB for almost 1 year.
    I have noticed intermittent "host unreachable" detected from NLB in each host from time to time since 3 weeks ago. After servers are rebooted, both hosts can be reached and can be detected from NLB manager. However it becomes unreachable in both
    servers within minutes and then becomes reachable again after several minutes. This behavior is noticed in the load balancer and pings do not work between the two hosts when the issue occurs. I did a packet capture to see what was going on with ARP message
    when the issue occurs. ARP entry goes missing in each server when the problem occurs and no ARP replies are returned from each server. But ARP requests are dispatched from both servers when the issue occurs. ARP replies come back after sometime after which
    hosts become reachable again.
    I tried to create a permanent static ARP entry (By copying the MAC address from ARP table when the two hosts are reachable) in each host but that hasn't solved the issue either. It seems like the individual MAC address generated by each host is a virtual
    one and it doesn't seem to respond when the problem occurs.
    However load balancing and web sites are fully functional without any issues even while "host unreachability" issue is detected.
    Appreciate if someone could help me to dig the real problem out.
    Thank you.

    Hi,
    Did you do some change of your network or the NLB firewall settings recently?
    If you are using the NLB cluster in Hyper-V guest vm you need to enable the spoofing of MAC address.
    The related article:
    Cannot access the virtual or dedicated IP address of an NLB node (Guest) running in Unicast Mode on Windows Server 2008 R2 Hyper-V
     http://blogs.technet.com/b/networking/archive/2010/02/12/cannot-access-the-virtual-or-dedicated-ip-address-of-an-nlb-node-guest-running-in-unicast-mode-on-windows-server-2008-r2-hyper-v.aspx
    More information:
    Selecting the Unicast or Multicast Method of Distributing Incoming Requests
    http://technet.microsoft.com/en-us/library/cc782694(v=ws.10).aspx
    Single network adapter
    http://technet.microsoft.com/en-us/library/cc776178(v=ws.10).aspx
    Hope this helps.
    We
    are trying to better understand customer views on social support experience, so your participation in this
    interview project would be greatly appreciated if you have time.
    Thanks for helping make community forums a great place.

  • Using javascript to delay flash banner from loading

    I have a website built in HTML with a small flash banner. My
    problem is that the flash loads before the rest of the page loads.
    Is there a way to delay the flash from loading using javascript
    until the rest of the page has loaded?
    Thanks for your help.

    It is a bit complicated but you can set a delayed function,
    where you will load the flash banner:
    var interval;
    interval = window.setInterval("loadBanner()", 1000);
    var i = 0;
    function loadBanner() {
    // code for banner load
    it is not a best methode but it works,
    Titti
    http://textures.z7server.com/

  • Lost CC trial after windows 8.1 update.

    after a windows update loads of files and programmes simply disappeared from the laptop,including my trial of CC.
    when we tried to reinstall it, a message appeared saying everything was up to date so no joy downloading the programme again.
    however all the files from the programme have vanished so i am stuck.
    i was only a few days into the trial and hadnt used it that much so would like to carry trialing it.
    hope you can help

    Sheffieldchap for information on how to reinstall the Adobe Creative applications please see CC desktop lists applications as "Up to Date" when not installed. 

  • Delay after key stroke in iPhoto following latest update

    I just updated to the latest version of iPhoto in the hope of seeing improvements which I am sure they are. However, right now, the only change I see is that there is a delay after each character I type in the legend.  It is unbearable and close to being unsusable.  Is anyone else experiencing this issue and were you able to fix it somehow?

    Make a temporary, backup copy (if you don't already have a backup copy) of the library and try the following:
    1 - delete the iPhoto preference file, com.apple.iPhoto.plist, that resides in your
         User/Home()/Library/ Preferences folder.
    2 - delete iPhoto's cache file, Cache.db, that is located in your
         User/Home()/Library/Caches/com.apple.iPhoto folder. 
    Click to view full size
    3 - launch iPhoto and try again.
    NOTE: If you're moved your library from its default location in your Home/Pictures folder you will have to point iPhoto to its new location when you next open iPhoto by holding down the Option key when launching iPhoto.  You'll also have to reset the iPhoto's various preferences.
    NOTE 2:  In Lion and Mountain Lion the Library folder is now invisible. To make it permanently visible enter the following in the Terminal application window: chflags nohidden ~/Library and hit the Enter button - 10.7: Un-hide the User Library folder.
    OT

Maybe you are looking for