Design for 600 APs

Hello,
I would like to know what is the best design to deploy 600 APs on 4 Wism (on 2 6509, two Wism per 6509, so 4 controllers per 6509). The capacity of the whole is 1200 APs to keep redundancy.
I remembered that the best practice for standalone AP was one hundrer APs per Vlan. Is it the same with Wism ? So do I have to create 16 Ap Managers:
> one controller on a wism = 150 Aps, so 2 Aps Managers / controller
Is it a good way to deploy the AP or can you advise a better design ?
Thanks a lot,
Best regards,
Gerald.

And CAPWAP (use for traffic between AP and WLC WISM) is L3 only. You could use 2,3 or more vlan for your AP. Each AP use IP of AP Manager (learn by dhcp, dns,...) for join the WLC.
Christian

Similar Messages

Wireless AP design for Wireless IPPhone 7921

FOr a client they are asking 40 Wireless IP Phone, with 3 floors, IPT side I am clear in design, but for access point design I am bit confused with standalone and WLC design.
Could please light me on Wireless design for standalone AP and WLC controller with AP , in the design plan to give both as options.
And also how to confirm a AP is a standalone or it wil work only with WLC.
Please light me with wireless design for IPT.

I would suggest you subcontract this to a partner who is familiar with wireless voice designs. There are a lot of details and caveats to make sure it works.
For example: autonomous APs are not viable for voice installations. You need a controller to prevent the roam times from interrupting the call.
At a minimum, you should read the Voice over Wireless LAN Design Guide:
http://www.cisco.com/en/US/solutions/ns340/ns414/ns742/ns820/landing_voice_wireless.html

Antennas for 1260 APs

Hi,
I was wondering what anntenna options do I have for the 1260 APs. Will any Cisco 2.4/5.8 capable antennas fit the bill? Meaning, is it only the AP that provides the "N" ability? Or, are there only certain 2.4/5.8 antennas that go with the 1260s to provide the "N" speeds. Our current antennas are AIR-ANTM4050V-R. Also, How many antennas will I need per 1260 AP for optimum performance?
Thanks, Pat.

Hi Pat,
you'd find all the antennas specially for the 802.11n AP in this document....
http://www.cisco.com/en/US/prod/collateral/wireless/ps7183/ps469/at_a_glance_c45-513837.pdf
Right from the document...
"Although most existing Cisco antennas can be used, Cisco has developed antennas
specifically designed for use with 802.11n access points to optimize performance."
If you plan to use both frequency bands you'll need 6 antennas per AP.
Kind regards,
Ron

How will an external Hard drive designed for the macbook Pro work with my White Macbook? My white macbook has a Firewire 400 and the G-Tech HD has a 800 to 400 compatible cable for the firewire.

I am asking this because I want the G-Tech Hard drive says that it is designed for the macbook pro. Yet, I want to back up faster with by using my firewire 400 which is not an option on the one designed for the white macbook that does not have a firewire (only a USB port.) The G-Tech Hard drive comes with the 800 to 400 compatible cable and has 5400 RPM with 750 GB. Also, I've heard that laptops with low battery (mine all the time) won't have the power for a bus powered Hard drive (as in no ac plug in adaptor.) Can I just plug in my laptop? Any one know the answers from experience with this hard drive?

As far as I know, if a harddrive works with a Macpro, it should work with the Macbook: if your Macbook is low on power, plug in the AC adapter
If your Macbook has a firewire port, then it should be fine. BUt i would do somemore research first.

Is this the best design for asynchronous notifications (such as email)? Current design uses Web Site, Azure Service Bus Queue, Table Storage and Cloud Service Worker Role.

I am asking for feedback on this design. Here is an example user story:
As a group admin on the website I want to be notified when a user in my group uploads a file to the group.
Easiest solution would be that in the code handling the upload, we just directly create an email message in there and send it. However, this seems like it isn't really the appropriate level of separation of concerns, so instead we are thinking to have a separate
worker process which does nothing but send notifications. So, the website in the upload code handles receiving the file, extracting some metadata from it (like filename) and writing this to the database. As soon as it is done handling the file upload it then
does two things: Writes the details of the notification to be sent (such as subject, filename, etc...) to a dedicated "notification" table and also creates a message in a queue which the notification sending worker process monitors. The entire sequence
is shown in the diagram below.
My questions are: Do you see any drawbacks in this design? Is there a better design? The team wants to use Azure Worker Roles, Queues and Table storage. Is it the right call to use these components or is this design unnecessarily complex? Quality attribute
requirements are that it is easy to code, easy to maintain, easy to debug at runtime, auditable (history is available of when notifications were sent, etc...), monitor-able. Any other quality attributes you think we should be designing for?
More info:
We are creating a cloud application (in Azure) in which there are at least 2 components. The first is the "source" component (for example a UI / website) in which some action happens or some condition is met that triggers a second component or "worker"
to perform some job. These jobs have details or metadata associated with them which we plan to store in Azure Table Storage. Here is the pattern we are considering:
Steps:
Condition for job met.
Source writes job details to table.
Source puts job in queue.
Asynchronously:
Worker accepts job from queue.
Worker Records DateTimeStarted in table.
Queue marks job marked as "in progress".
Worker performs job.
Worker updates table with details (including DateTimeCompleted).
Worker reports completion to queue.
Job deleted from queue.
Please comment and let me know if I have this right, or if there is some better pattern. For example sake, consider the work to be "sending a notification" such as an email whose template fields are filled from the "details" mentioned in
the pattern.

Hi,
Thanks for your posting.
This development mode can exclude some errors, such as the file upload complete at the same time... from my experience, this is a good choice to achieve the goal.
Best Regards,
Jambor
We are trying to better understand customer views on social support experience, so your participation in this interview project would be greatly appreciated if you have time. Thanks for helping make community forums a great place.
Click
HERE to participate the survey.

I am updating iphoto 9.1 to 9.3 and every time when I clicked for update aps store asked to open it in the account where you purchased. I am using the same account and its available in the purchased item of this account. Can someone resolve this problem.

I am updating iphoto 9.1 to 9.3 and every time when I clicked for update aps store asked to open it in the account where you purchased. I am using the same account and its available in the purchased item of this account. But in my purchased item library it indicates that you update iPhoto. I am not sure which account the aps store asking. Can someone resolve this problem.

Contact App Store support. They're the folks who can help with Account issues.
Regards
TD

Generate Prime Interface Availability and Utilization Report for unified APs

Hi,
I´m trying to generate interface availability and interface utilization report for unified APs on Prime Infrastructure 2.0, but it doesn´t display any information. I have created device health and interface health templates under desing/Monitor configuration/My templates and deployed under Deploy/Monitoring deployment, but it still don´t show any information,
thaks for your help.

Hi Alejandro,
Did you solve this problem? Or is it a bug?
I face the some issue with you, I just run "Report/Report Launch Pad/Deivce/Interface Utilization"
and then I create a report for interface utilization.
But it display nothing when the report run finished.
I ask some guys in this forum, they said maybe it's a PI2.1 bug.
BR
Frank

Print Layout Designer for UDO

Hi,
Can we design report with print layout designer for UDO forms?
If yes, how do we accomplish this?
If not, is there any other alternative?
I am using 2004B. Thanks.

I use the iTextSharp project to create PDF's (http://itextsharp.sourceforge.net/)... its free and it works (A little hard to use, but it works). A more simple PDF-project are SharpPDF (http://sharppdf.sourceforge.net/). This is also free and very easy to use, but not that many features.

How can I see if my program is for more than one user? We think we have bought in design for more users, but can not find out how to get in for more than one?

How can I see if my program is for more than one user? We think we have bought in design for more users, but can not find out how to get in for more than one?

If you bought a CC for team, you can log in at http://adobe.com and insert the e-mail that you gave at the moment at the purchase and than you can manage and see you product/plan/team.
If I was not clear you can use the following link to help you solving your issue:
Creative Cloud Help | Manage your Creative Cloud for teams membership
If your not clear about this situation, contact with an agent of Adobe, by chat or phone. Use the following link to see the type of support you have on this matter:
http://adobe.com/getsupport
I think this will help you.
Regards

Getting error while publishing workflow using SP designer for SharePoint 2013

Hi,
I am try to setup Workflow manager for our sharepoint applications.
WF manager set ran without any issue.
I registered the SPWorkflow service which succeeded as well. The Workflow service application shows "Workflow is connected"
I am creating a workflow using sharepoint designer using my credential (not Service account). I am able to save it but while publishing, its prompting with an error.
The error says "Errors were found while compiling the workflow.The workflow files were saved but cannot run." Clicking advanced button show
"Microsoft.SharePoint.SPException: We're sorry, we weren't able to complete the operation, please try again in a few minutes. If you see this message repeatedly, contact your administrator.
at Microsoft.SharePoint.SPScaleOutDatabaseMap.CreateSqlSession(ISPScaleOutDatabaseMapProvider mapProvider, Byte[] compositeKey, Guid forceRefreshVersion, Guid& version)
at Microsoft.SharePoint.SPScaleOutDatabaseCommandExecutor.Execute(ExecuteDelegate operation, ISPScaleOutDatabaseMapProvider mapProvide"
Any help would be highly appreciated
Thanks,

Hi,
According to your post, my understanding is that you got error while publishing workflow using SharePoint designer for SharePoint 2013.
Please check whether the Central Admin > Manage Service Application-> “App Management Service” is started.
Please check whether the “Configure service application associations”, ”App Management Service” is already associated.
Then please check whether the “Manage Services on server” and the “App Management Service” is started.
In addition, please try to re-register Workflow Service.
If the issues still exists, please follow the steps in the
Steps to Verify that Server Is Correctly Set Up. After you verified that the server is correctly set up, follow the steps in the
Steps to Troubleshoot Workflow Management Service and
Troubleshooting the Service Bus for Windows Server then retry your action related to publishing workflows
More information:
http://wp.ahcheng.com/2013/03/23/error-were-found-when-compiling-the-workflow-the-workflow-files-were-saved-but-cannot-be-run/
http://sp2013.pro/2013/04/solution-errors-were-found-when-compiling-the-workflow-the-workflow-files-were-saved-but-cannot-be-run-cannot-set-unknown-member/
Best Regards,
Linda Li
Linda Li
TechNet Community Support

This workflow cannot be imported because it was created in SharePoint Designer for a different Site

Hello everyone. I am getting this error when attempting to move minor workflow changes from mirror SharePoint development / production environments and hoping someone can help me.
"This workflow cannot be imported because it was created in SharePoint Designer for a different site, or the original workflow has been moved or deleted. To move a workflow between sites, use Save as Template (.wsp file) instead of a Visio workflow
drawing."
So basically I have taken an image of our single SharePoint server, Domain Controller, and a client and restored them to an OFFLINE development environment for the testing of workflow changes prior to production. I've put quite a bit of time into one
particularly and would like to export/import rather than re-created from scratch.
I've successfully created the form template and imported. This created the necessary list items nicely and the form appears to work as expected. However, when attempting to import the .VWI file exported from dev SharePoint, I am getting the above
error. If I change the .VWI to .zip and remove the "workflow.xoml.wfconfig.xml" file, then re-zip and change the file extension back to .VWI I get a dialog that allows me to import, but I have to choose a new name and much of the related content
is lost. I need to be able to overwrite/merge the existing workflow with the import. Any suggestions?
One strange thing I ran into was during a test of an export/import from and to the exact same environment. If I simply export to .VWI, then import from .VWI with no changes, SAME everything I still get this error. Very weird. Hoping someone can shed some
light on the subject. Thank you.
Adam Tyler

Hi Adam,
Here is a blog talk about the same issue would be helpful:
http://techiescode.blogspot.com/2014/09/copymove-sharepoint-2010-designer.html
Best Regards
Dennis Guo
TechNet Community Support

I've just bought a Macbook Pro 15" and I'm trying to use Photoshop, but the resolution its displaying the images at for 100% are too small. I have to design for the web, so need to be intricate with detail, but I'm finding it adjusts the resolution of the

I've just bought a Macbook Pro 15" and I'm trying to use Photoshop, but the resolution its displaying the images at for 100% are too small. I have to design for the web, so need to be intricate with detail, but I'm finding it adjusts the resolution of the image right down. (I mean you can see the image clearly, but it's too small to edit). When I look at Safari and see a web page at 100% it's clear, but the same page displayed in Photoshop CC appears 50% of the size (even though it says it's 100%) If I move the application window to another screen it adjusts it correctly – leaving all the pallettes, menus and tools correctly sized as they are on the retina display Is there some way to adjust the way Photoshop CC displays images so it is more consistent with what you actually see? There doesn't seem to be any answer on the Adobe forum, so hopefully someone here can shed some light. MacBook Pro with Retina display, 15", OS X Yosemite (10.10.2), Photoshop CC 2014

I tested both ways. With "open in low resolution" ckecked the size of the images is cool, but it is low-resolution including Photoshop appearance.
If "open in low resolution" is unckecked the appearance is good but the very small size.
See the image below. It has 650 x 732 px, 72 dpi. The font of the text "Neste aniversário ..." is with 18pt.

HT4623 i am trying to update my Ipad 1 but it tells me i have no updates available under my general settings. i talked to someone on the phone yesterday and they said my software version is 2 updates behind. i paid for some aps and they will not open wit

i am trying to update my Ipad 1 but it tells me i have no updates available under my general settings. i talked to someone on the phone yesterday and they said my software version is 2 updates behind. i paid for some aps and they will not open with my cu

You are as far as you can be with the original iPad; only iPad 2 and greater will update to 7+

Architectural design for FTP batch processing

Hello gurus,
I would like your help in determining the design for the following.
We receive several HL7 messages as a text file and copied to a shared network folder. All these files are created into several different folders depending on the region, message type. We need to come up with a B2B process to read all the files from the netwrok folder using FTP (batch process) and translate if needed (depending on the scenario) and transfer the files over to other destination folder on the network (using FTP).
For this, we can create TPs with Generic FTP channel and this works without any issues. By doing this way, we need to create TP for each and every type of message which reads the files from its own specified directory location on the network based on the the polling interval.
My question is, instead of creating TPs for each and every type of file, is there a way by which I can write a common web service that reads the source files from the network and based on the type of the file route to the proper destination folders. If it is possible, I would like to know the architecture for accomplishing this task.
I really appreciate your kind help on this.
Thanks and regards,
Raghu

Hi Raghu,
Is it a B2B communication scenario?
By doing this way, we need to create TP for each and every type of message which reads the files from its own specified directory location on the network based on the the polling interval.Why cann't you have only one TP with multiple documents, channels and agreements?
My question is, instead of creating TPs for each and every type of file, is there a way by which I can write a common web service that reads the source files from the network and based on the type of the file route to the proper destination folders. If it is possible, I would like to know the architecture for accomplishing this task.Depends on your use case and products you want to use. You can very well use FTP adapter with BPEL and poll for files. Use DVM in composite to figure out the destination and send it there. You may use OSB if it is a typical routing case with heavy load and performance is a concern. You may use B2B as well here. So ultimately you need to figure out what you want and what tools you want to use.
Regards,
Anuj

I received a car charger for xmas. I have an iPhone 4. Is there a difference in the charging dock between the older and newer iphones? I don't want to damage it by shoving a cable in that is designed for a newer model.

I received a car charger for xmas. I have an iPhone 4. Is there a difference in the charging dock between the older and newer iphones? I don't want to damage it by shoving a cable in that is designed for a newer model.

there are 2 connectors the old pin30 and the new ligthing bolt
they don't look very much alike so if anybody were damage byt forcing it in it would be their own fault seeing how diffrent they are

Design for 600 APs

Similar Messages

Maybe you are looking for