Discrepancy message Link Duplex Mismatch

I got a lot of Discrepancy messages that operation team said that are wrong messages. one of them is below :
[sc11601.stc.com.sa,FastEthernet7/1],[rc11601.stc.com.sa,FastEthernet12/0/1]
interface FastEthernet7/1
description P2P.RC11601.SC11601 -> RC11601 FE12/0/1
ip vrf forwarding COM/IS
ip address 172.20.2.62 255.255.255.252
ip accounting output-packets
ip ospf network point-to-point
speed 100
duplex full
wrr-queue bandwidth 70 30
wrr-queue queue-limit 60 20
wrr-queue cos-map 1 2 0 1
wrr-queue cos-map 2 2 2 3 6 7
mls qos trust dscp
end
SC11601#sh interfaces FastEthernet7/1
FastEthernet7/1 is up, line protocol is up (connected)
Hardware is C6k 100Mb 802.3, address is 00d0.00ec.7400 (bia 00d0.00ec.7400)
Description: P2P.RC11601.SC11601 -> RC11601 FE12/0/1
Internet address is 172.20.2.62/30
MTU 1500 bytes, BW 100000 Kbit, DLY 100 usec,
     reliability 255/255, txload 1/255, rxload 98/255
Encapsulation ARPA, loopback not set
Keepalive set (10 sec)
Full-duplex, 100Mb/s
input flow-control is off, output flow-control is unsupported
ARP type: ARPA, ARP Timeout 04:00:00
Last input 00:00:00, output 00:00:00, output hang never
Last clearing of "show interface" counters never
Input queue: 0/75/0/123 (size/max/drops/flushes); Total output drops: 62970
Queueing strategy: fifo
Output queue: 0/40 (size/max)
5 minute input rate 38682000 bits/sec, 18397 packets/sec
5 minute output rate 179000 bits/sec, 166 packets/sec
L2 Switched: ucast: 11975833 pkt, 1479635171 bytes - mcast: 14194902 pkt, 3811719114 bytes
L3 in Switched: ucast: 429215085703 pkt, 94830171248319 bytes - mcast: 0 pkt, 0 bytes mcast
L3 out Switched: ucast: 6824514014 pkt, 1288372109867 bytes mcast: 0 pkt, 0 bytes
     430025276460 packets input, 94920777016321 bytes, 0 no buffer
     Received 14799648 broadcasts, 0 runts, 0 giants, 0 throttles
     0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored
     0 input packets with dribble condition detected
     7696316854 packets output, 1389443700164 bytes, 0 underruns
     0 output errors, 0 collisions, 2 interface resets
     0 babbles, 0 late collision, 0 deferred
     0 lost carrier, 0 no carrier
     0 output buffer failures, 0 output buffers swapped out
SC11601#
other interface:
interface FastEthernet12/0/1
description P2P.RC11601.SC11601
ip vrf forwarding COM/IS
ip address 172.20.2.61 255.255.255.252
no ip directed-broadcast
ip accounting output-packets
ip route-cache flow
ip ospf network point-to-point
load-interval 30
full-duplex
service-policy input Set-Experimental-COM/IS
service-policy output HSBB-Policy
end
RC11601#sh interfaces FastEthernet12/0/1
FastEthernet12/0/1 is up, line protocol is up
Hardware is cyBus FastEthernet Interface, address is 0010.0d59.0981 (bia 0010.0d59.0981)
Description: P2P.RC11601.SC11601
Internet address is 172.20.2.61/30
MTU 1500 bytes, BW 100000 Kbit, DLY 100 usec, rely 255/255, load 85/255
Encapsulation ARPA, loopback not set
Keepalive set (10 sec)
Full-duplex, 100Mb/s, 100BaseTX/FX
ARP type: ARPA, ARP Timeout 04:00:00
Last input 00:00:00, output 00:00:00, output hang never
Last clearing of "show interface" counters 2w6d
Input queue: 0/75/6/0 (size/max/drops/flushes); Total output drops: 238552
Queueing strategy: VIP-based fair queuing
30 second input rate 167000 bits/sec, 148 packets/sec
30 second output rate 33621000 bits/sec, 17158 packets/sec
     266182338 packets input, 34247141843 bytes, 0 no buffer
     Received 693431 broadcasts, 0 runts, 0 giants, 1 throttles
     0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored
     0 watchdog, 0 multicast
     0 input packets with dribble condition detected
     27319889810 packets output, 6807897544306 bytes, 0 underruns
     0 output errors, 0 collisions, 0 interface resets
     0 babbles, 0 late collision, 0 deferred
     0 lost carrier, 0 no carrier
     0 output buffer failures, 0 output buffers swapped out

momsrv02:/ # snmpwalk rc11601 1.3.6.1.2.1.2.2.1.2
interfaces.ifTable.ifEntry.ifDescr.1 : DISPLAY STRING- (ascii): GigabitEthernet1/0/0
interfaces.ifTable.ifEntry.ifDescr.2 : DISPLAY STRING- (ascii): Serial2/0
interfaces.ifTable.ifEntry.ifDescr.3 : DISPLAY STRING- (ascii): Serial2/1
interfaces.ifTable.ifEntry.ifDescr.4 : DISPLAY STRING- (ascii): Serial2/2
interfaces.ifTable.ifEntry.ifDescr.5 : DISPLAY STRING- (ascii): Serial2/3
interfaces.ifTable.ifEntry.ifDescr.6 : DISPLAY STRING- (ascii): Serial2/4
interfaces.ifTable.ifEntry.ifDescr.7 : DISPLAY STRING- (ascii): Serial2/5
interfaces.ifTable.ifEntry.ifDescr.8 : DISPLAY STRING- (ascii): Serial2/6
interfaces.ifTable.ifEntry.ifDescr.9 : DISPLAY STRING- (ascii): Serial2/7
interfaces.ifTable.ifEntry.ifDescr.10 : DISPLAY STRING- (ascii): Serial3/0
interfaces.ifTable.ifEntry.ifDescr.11 : DISPLAY STRING- (ascii): Serial3/1
interfaces.ifTable.ifEntry.ifDescr.12 : DISPLAY STRING- (ascii): Serial3/2
interfaces.ifTable.ifEntry.ifDescr.13 : DISPLAY STRING- (ascii): Serial3/3
interfaces.ifTable.ifEntry.ifDescr.14 : DISPLAY STRING- (ascii): Serial3/4
interfaces.ifTable.ifEntry.ifDescr.15 : DISPLAY STRING- (ascii): Serial3/5
interfaces.ifTable.ifEntry.ifDescr.16 : DISPLAY STRING- (ascii): Serial3/6
interfaces.ifTable.ifEntry.ifDescr.17 : DISPLAY STRING- (ascii): Serial3/7
interfaces.ifTable.ifEntry.ifDescr.18 : DISPLAY STRING- (ascii): Serial4/0
interfaces.ifTable.ifEntry.ifDescr.19 : DISPLAY STRING- (ascii): Serial4/1
interfaces.ifTable.ifEntry.ifDescr.20 : DISPLAY STRING- (ascii): Serial4/2
interfaces.ifTable.ifEntry.ifDescr.21 : DISPLAY STRING- (ascii): Serial4/3
interfaces.ifTable.ifEntry.ifDescr.22 : DISPLAY STRING- (ascii): Serial4/4
interfaces.ifTable.ifEntry.ifDescr.23 : DISPLAY STRING- (ascii): Serial4/5
interfaces.ifTable.ifEntry.ifDescr.24 : DISPLAY STRING- (ascii): Serial4/6
interfaces.ifTable.ifEntry.ifDescr.25 : DISPLAY STRING- (ascii): Serial4/7
interfaces.ifTable.ifEntry.ifDescr.26 : DISPLAY STRING- (ascii): Serial5/0
interfaces.ifTable.ifEntry.ifDescr.27 : DISPLAY STRING- (ascii): Serial5/1
interfaces.ifTable.ifEntry.ifDescr.28 : DISPLAY STRING- (ascii): Serial5/2
interfaces.ifTable.ifEntry.ifDescr.29 : DISPLAY STRING- (ascii): Serial5/3
interfaces.ifTable.ifEntry.ifDescr.30 : DISPLAY STRING- (ascii): Serial5/4
interfaces.ifTable.ifEntry.ifDescr.31 : DISPLAY STRING- (ascii): Serial5/5
interfaces.ifTable.ifEntry.ifDescr.32 : DISPLAY STRING- (ascii): Serial5/6
interfaces.ifTable.ifEntry.ifDescr.33 : DISPLAY STRING- (ascii): Serial5/7
interfaces.ifTable.ifEntry.ifDescr.34 : DISPLAY STRING- (ascii): FastEthernet8/0/0
interfaces.ifTable.ifEntry.ifDescr.35 : DISPLAY STRING- (ascii): FastEthernet8/0/1
interfaces.ifTable.ifEntry.ifDescr.36 : DISPLAY STRING- (ascii): E1 8/1/0
interfaces.ifTable.ifEntry.ifDescr.37 : DISPLAY STRING- (ascii): E1 8/1/1
interfaces.ifTable.ifEntry.ifDescr.38 : DISPLAY STRING- (ascii): E1 8/1/2
interfaces.ifTable.ifEntry.ifDescr.39 : DISPLAY STRING- (ascii): E1 8/1/3
interfaces.ifTable.ifEntry.ifDescr.40 : DISPLAY STRING- (ascii): E1 8/1/4
interfaces.ifTable.ifEntry.ifDescr.41 : DISPLAY STRING- (ascii): E1 8/1/5
interfaces.ifTable.ifEntry.ifDescr.42 : DISPLAY STRING- (ascii): E1 8/1/6
interfaces.ifTable.ifEntry.ifDescr.43 : DISPLAY STRING- (ascii): E1 8/1/7
interfaces.ifTable.ifEntry.ifDescr.44 : DISPLAY STRING- (ascii): FastEthernet9/0/0
interfaces.ifTable.ifEntry.ifDescr.45 : DISPLAY STRING- (ascii): FastEthernet9/0/1
interfaces.ifTable.ifEntry.ifDescr.46 : DISPLAY STRING- (ascii): POS9/1/0
interfaces.ifTable.ifEntry.ifDescr.47 : DISPLAY STRING- (ascii): E1 10/0/0
interfaces.ifTable.ifEntry.ifDescr.48 : DISPLAY STRING- (ascii): E1 10/0/1
interfaces.ifTable.ifEntry.ifDescr.49 : DISPLAY STRING- (ascii): E1 10/0/2
interfaces.ifTable.ifEntry.ifDescr.50 : DISPLAY STRING- (ascii): E1 10/0/3
interfaces.ifTable.ifEntry.ifDescr.51 : DISPLAY STRING- (ascii): E1 10/0/4
interfaces.ifTable.ifEntry.ifDescr.52 : DISPLAY STRING- (ascii): E1 10/0/5
interfaces.ifTable.ifEntry.ifDescr.53 : DISPLAY STRING- (ascii): E1 10/0/6
interfaces.ifTable.ifEntry.ifDescr.54 : DISPLAY STRING- (ascii): E1 10/0/7
interfaces.ifTable.ifEntry.ifDescr.55 : DISPLAY STRING- (ascii): POS10/1/0
interfaces.ifTable.ifEntry.ifDescr.56 : DISPLAY STRING- (ascii): E1 11/1/0
interfaces.ifTable.ifEntry.ifDescr.57 : DISPLAY STRING- (ascii): E1 11/1/1
interfaces.ifTable.ifEntry.ifDescr.58 : DISPLAY STRING- (ascii): E1 11/1/2
interfaces.ifTable.ifEntry.ifDescr.59 : DISPLAY STRING- (ascii): E1 11/1/3
interfaces.ifTable.ifEntry.ifDescr.60 : DISPLAY STRING- (ascii): E1 11/1/4
interfaces.ifTable.ifEntry.ifDescr.61 : DISPLAY STRING- (ascii): E1 11/1/5
interfaces.ifTable.ifEntry.ifDescr.62 : DISPLAY STRING- (ascii): E1 11/1/6
interfaces.ifTable.ifEntry.ifDescr.63 : DISPLAY STRING- (ascii): E1 11/1/7
interfaces.ifTable.ifEntry.ifDescr.64 : DISPLAY STRING- (ascii): FastEthernet12/0/0
interfaces.ifTable.ifEntry.ifDescr.65 : DISPLAY STRING- (ascii): FastEthernet12/0/1
interfaces.ifTable.ifEntry.ifDescr.66 : DISPLAY STRING- (ascii): POS12/1/0
interfaces.ifTable.ifEntry.ifDescr.67 : DISPLAY STRING- (ascii): Null0
interfaces.ifTable.ifEntry.ifDescr.68 : DISPLAY STRING- (ascii): Loopback1
interfaces.ifTable.ifEntry.ifDescr.69 : DISPLAY STRING- (ascii): Serial8/1/0:0
interfaces.ifTable.ifEntry.ifDescr.70 : DISPLAY STRING- (ascii): Serial8/1/1:0
interfaces.ifTable.ifEntry.ifDescr.71 : DISPLAY STRING- (ascii): Serial8/1/2:0
interfaces.ifTable.ifEntry.ifDescr.72 : DISPLAY STRING- (ascii): Serial8/1/3:0
interfaces.ifTable.ifEntry.ifDescr.73 : DISPLAY STRING- (ascii): Serial8/1/4:0
interfaces.ifTable.ifEntry.ifDescr.74 : DISPLAY STRING- (ascii): Serial8/1/5:0
interfaces.ifTable.ifEntry.ifDescr.75 : DISPLAY STRING- (ascii): Serial8/1/6:0
interfaces.ifTable.ifEntry.ifDescr.76 : DISPLAY STRING- (ascii): Serial8/1/7:0
interfaces.ifTable.ifEntry.ifDescr.77 : DISPLAY STRING- (ascii): Serial10/0/0:0
interfaces.ifTable.ifEntry.ifDescr.78 : DISPLAY STRING- (ascii): Serial10/0/1:0
interfaces.ifTable.ifEntry.ifDescr.79 : DISPLAY STRING- (ascii): Serial10/0/2:0
interfaces.ifTable.ifEntry.ifDescr.80 : DISPLAY STRING- (ascii): Serial10/0/3:0
interfaces.ifTable.ifEntry.ifDescr.81 : DISPLAY STRING- (ascii): Serial10/0/4:0
interfaces.ifTable.ifEntry.ifDescr.82 : DISPLAY STRING- (ascii): Serial10/0/5:0
interfaces.ifTable.ifEntry.ifDescr.83 : DISPLAY STRING- (ascii): Serial10/0/6:0
interfaces.ifTable.ifEntry.ifDescr.84 : DISPLAY STRING- (ascii): Serial10/0/7:0
interfaces.ifTable.ifEntry.ifDescr.85 : DISPLAY STRING- (ascii): Serial11/1/0:0
interfaces.ifTable.ifEntry.ifDescr.86 : DISPLAY STRING- (ascii): Serial11/1/1:0
interfaces.ifTable.ifEntry.ifDescr.87 : DISPLAY STRING- (ascii): Serial11/1/2:0
interfaces.ifTable.ifEntry.ifDescr.88 : DISPLAY STRING- (ascii): Serial11/1/3:0
interfaces.ifTable.ifEntry.ifDescr.89 : DISPLAY STRING- (ascii): Serial11/1/4:0
interfaces.ifTable.ifEntry.ifDescr.90 : DISPLAY STRING- (ascii): Serial11/1/5:0
interfaces.ifTable.ifEntry.ifDescr.91 : DISPLAY STRING- (ascii): Serial11/1/6:0
interfaces.ifTable.ifEntry.ifDescr.92 : DISPLAY STRING- (ascii): Serial11/1/7:0
interfaces.ifTable.ifEntry.ifDescr.93 : DISPLAY STRING- (ascii): Loopback0
interfaces.ifTable.ifEntry.ifDescr.94 : DISPLAY STRING- (ascii): GigabitEthernet1/0/0-mpls layer
interfaces.ifTable.ifEntry.ifDescr.95 : DISPLAY STRING- (ascii): POS9/1/0-mpls layer
momsrv02:/ #

Similar Messages

LINK DUPLEX MISMATCH error

Hi all,
i am using cisco LMS 3.2 as when we run the Discripencies Report we get the
Error of LINK DUPLEX MISMATCH....
Kindly guide for the same....
This link has ports with mismatching duplex.
Port GigabitEthernet0/23 on device MKT_1 with mode auto-duplex
Device type and OS version of MKT_1:
Cisco IOS Software, C3560E Software (C3560E-UNIVERSALK9-M), Version 12.2(53)SE2, RELEASE SOFTWARE (fc3)
Technical Support: http://www.cisco.com/techsupport
Port GigabitEthernet0/1 on device MKT_3 with mode full-duplex This link has ports with mismatching duplex.
Port GigabitEthernet0/23 on device MKT with mode auto-duplex
Device type and OS version of MKT_1:
Cisco IOS Software, C3560E Software (C3560E-UNIVERSALK9-M), Version 12.2(53)SE2, RELEASE SOFTWARE (fc3)
Technical Support: http://www.cisco.com/techsupport
Port GigabitEthernet0/1 on device MKT_3 with mode full-duplex
But when i check the configuration of both switches it shows as FULL DUPLEX for the above....
Kindly guide how to resolve the above error....

This is a known issue with ports set to auto-duplex. Since the switches do not reflect the current operational duplex, LMS does not know if the port negotiated to full or half. In that case, it presents the warning so you can investigate. Once you've confirmed the duplex is correct, you can acknowledge the discrepancy.
If you upgrade your switches to 12.2(55)SE, then the switch will report the operational duplex, and this discrepancy will go away on its own. The bug that fixed this was CSCtc12593

Duplex mismatch between N7k and 5508

Hi All,
I met a duplex mismatch issue in our new DC.
The port configuration on the N7k and controller is the same as in other DC
Only difference is version of the NxOS on the N7k.
On N7k 5.2(1) works
On N7k 5.2(7) i get below logs :
2013 Aug 21 22:23:24 xxx %CDP-4-DUPLEX_MISMATCH: Duplex mismatch discovered on Ethernet10/8, with LAGInterface0/3/1
2013 Aug 21 22:24:24 xxx last message repeated 8 times
2013 Aug 21 22:25:24 xxx last message repeated 8 times
2013 Aug 21 22:27:24 xxx last message repeated 16 times
2013 Aug 21 22:29:24 xxx last message repeated 16 times
Port configuration :
interface Ethernet10/8
description WLC 5508-1
switchport
switchport mode trunk
switchport trunk native vlan 50
switchport trunk allowed vlan 50,500,570
spanning-tree port type edge trunk
channel-group 1100
no shutdown
xxx# sh int e 10/8
Ethernet10/8 is up
Dedicated Interface
Belongs to Po1100
Hardware: 10/100/1000 Ethernet, address: 0006.f6b1.d2f7 (bia 0006.f6b1.d2f7)
Description:WLC 5508-1
MTU 1500 bytes, BW 1000000 Kbit, DLY 10 usec
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation ARPA
Port mode is trunk
full-duplex, 1000 Mb/s
Controller 5508 version 7.3.112.0
Controller ports :
Port Summary
           STP   Admin   Physical   Physical   Link   Link
Pr Type   Stat   Mode     Mode      Status   Status Trap     POE    SFPType
1 Normal Forw Enable Auto       1000 Full Up     Enable N/A     1000BaseTX
2 Normal Forw Enable Auto       1000 Full Up     Enable N/A     1000BaseTX
3 Normal Forw Enable Auto       1000 Full Up     Enable N/A     1000BaseTX
4 Normal Forw Enable Auto       1000 Full Up     Enable N/A     1000BaseTX
How can i fix this issue ? Ports are set up and show the same - 1000 / Full
the messages are annoying as loggs are almost full of them.
Thank you in advance

Hi Matthew,
The issue is related to bug -> "CDP duplex mismatch when using LAG on 5508 & 8510 WLC” (CSCuc94082)
The fastest way to solve (workaround) this is disable cdp on the controller by executing following command: config cdp advertise-v2 disable
Hope this helped you
Regards,
Radek

Nexus 5k Throwing Duplex Mismatch error even though Duplex/speed is correct

Hello Guys
We Are facing an issue with Duplex Match. error in nexus 5k
Our Nexus 5k Switch continously throwing Duplex mismtach error on Logs.
2013 Nov 9 07:53:24 FRMA_BK2_CSN5K_02 %CDP-4-DUPLEX_MISMATCH: Duplex mismatch discovered on Ethernet1/11, with LAGInterface0/3/1
2013 Nov 9 07:54:24 FRMA_BK2_CSN5K_02 last message repeated 8 times
2013 Nov 9 07:56:24 FRMA_BK2_CSN5K_02 last message repeated 16 times
2013 Nov 9 07:58:24 FRMA_BK2_CSN5K_02 last message repeated 16 times
2013 Nov 9 08:00:24 FRMA_BK2_CSN5K_02 last message repeated 16 times
2013 Nov 9 08:02:24 FRMA_BK2_CSN5K_02 last message repeated 16 times
2013 Nov 9 08:04:24 FRMA_BK2_CSN5K_02 last message repeated 16 times
2013 Nov 9 08:06:24 FRMA_BK2_CSN5K_02 last message repeated 16 times
2013 Nov 9 08:08:24 FRMA_BK2_CSN5K_02 last message repeated 16 times
2013 Nov 9 08:10:24 FRMA_BK2_CSN5K_02 last message repeated 16 times
2013 Nov 9 08:12:24 FRMA_BK2_CSN5K_02 last message repeated 16 times
2013 Nov 9 08:14:24 FRMA_BK2_CSN5K_02 last message repeated 16 times
2013 Nov 9 08:16:24 FRMA_BK2_CSN5K_02 last message repeated 16 times
2013 Nov 9 08:18:22 FRMA_BK2_CSN5K_02 last message repeated 15 times
The interface is connected to Cisco Wireless lan controller(5508) using port-channel. Other interface in Port channel is not facing an Issue.
This interface is hardcoded with Speed 1000. Same config on WLC also Speed 1000. No ipunt errors observed in the interfaces
But in Switch cdp this interface is showing as Half duplex and flooding the 5k with logs
Please find the Interface configs & CDP outputs,
interface port-channel124
description Controller Wireless 5508
switchport mode trunk
spanning-tree bpduguard enable
speed 1000
storm-control broadcast level 80.00
storm-control multicast level 80.00
vpc 124
interface Eth 1/10 & 1/11 is binded in port channel 124.
Eth 1/10 --> dont have any Logs and showing full duplex in CDP.
Eth 1/11 --> Having Logs for duplex mismtach and showing half duplex
interface Ethernet1/10
description Controller Wireless 5508 - Port 1
switchport mode trunk
speed 1000
storm-control broadcast level 80.00
storm-control multicast level 80.00
channel-group 124
interface Ethernet1/11
description Controller Wireless 5508 - Port 2
switchport mode trunk
speed 1000
storm-control broadcast level 80.00
storm-control multicast level 80.00
channel-group 124
FRMA_BK2_CSN5K_02# sh int eth 1/10
Ethernet1/10 is up
Hardware: 1000/10000 Ethernet, address: 547f.ee33.d031 (bia 547f.ee33.d031)
Description: Controller Wireless 5508 - Port 1 - 10.80.82.240
MTU 1500 bytes, BW 1000000 Kbit, DLY 10 usec
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation ARPA
Port mode is trunk
full-duplex, 1000 Mb/s, media type is 10G
Beacon is turned off
Input flow-control is off, output flow-control is off
Rate mode is dedicated
Switchport monitor is off
EtherType is 0x8100
Last link flapped 16week(s) 6day(s)
Last clearing of "show interface" counters 35w2d
30 seconds input rate 6194968 bits/sec, 1211 packets/sec
30 seconds output rate 4498096 bits/sec, 1189 packets/sec
Load-Interval #2: 5 minute (300 seconds)
    input rate 4.81 Mbps, 875 pps; output rate 3.60 Mbps, 863 pps
RX
    2055924941 unicast packets 547924 multicast packets 1043625 broadcast pack
ets
    2057516490 input packets 1047388804413 bytes
    82164348 jumbo packets 0 storm suppression bytes
    0 runts 0 giants 0 CRC 0 no buffer
    0 input error 0 short frame 0 overrun   0 underrun 0 ignored
    0 watchdog 0 bad etype drop 0 bad proto drop 0 if down drop
    0 input with dribble 0 input discard
    0 Rx pause
TX
    2407546704 unicast packets 558419255 multicast packets 2765961466 broadcas
t packets
    5731927425 output packets 1625683967743 bytes
    342983729 jumbo packets
    0 output errors 0 collision 0 deferred 0 late collision
    0 lost carrier 0 no carrier 0 babble 0 output discard
    0 Tx pause
2 interface resets
FRMA_BK2_CSN5K_02# sh int eth 1/11
Ethernet1/11 is up
Hardware: 1000/10000 Ethernet, address: 547f.ee33.d032 (bia 547f.ee33.d032)
Description: Controller Wireless 5508 - Port 2 - 10.80.82.240
MTU 1500 bytes, BW 1000000 Kbit, DLY 10 usec
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation ARPA
Port mode is trunk
full-duplex, 1000 Mb/s, media type is 10G
Beacon is turned off
Input flow-control is off, output flow-control is off
Rate mode is dedicated
Switchport monitor is off
EtherType is 0x8100
Last link flapped 16week(s) 6day(s)
Last clearing of "show interface" counters 35w2d
30 seconds input rate 2059992 bits/sec, 712 packets/sec
30 seconds output rate 3605536 bits/sec, 680 packets/sec
Load-Interval #2: 5 minute (300 seconds)
    input rate 1.44 Mbps, 485 pps; output rate 2.73 Mbps, 546 pps
RX
    1742986162 unicast packets 712358 multicast packets 1587374 broadcast pack
ets
    1745285894 input packets 813329974630 bytes
    107173365 jumbo packets 0 storm suppression bytes
    0 runts 0 giants 0 CRC 0 no buffer
    0 input error 0 short frame 0 overrun   0 underrun 0 ignored
    0 watchdog 0 bad etype drop 0 bad proto drop 0 if down drop
    0 input with dribble 0 input discard
    0 Rx pause
TX
    1347189732 unicast packets 337957710 multicast packets 2429529386 broadcas
t packets
    4114676828 output packets 1302894776466 bytes
    308726768 jumbo packets
    0 output errors 0 collision 0 deferred 0 late collision
    0 lost carrier 0 no carrier 0 babble 0 output discard
    0 Tx pause
3 interface resets
FRMA_BK2_CSN5K_02# sh cdp neighbors interface ethernet 1/11 detail
Device ID:FRMA_BK2_WLCCS5508_01_100
System Name:
Interface address(es):
    IPv4 Address: 10.80.82.240
Platform: AIR-CT5508-K9, Capabilities: Host
Interface: Ethernet1/11, Port ID (outgoing port): LAGInterface0/3/1
Holdtime: 136 sec
Version:
Manufacturer's Name: Cisco Systems Inc. Product Name: Cisco Controller Product
Version: 7.0.240.0 RTOS Version: Erro Bootloader Version: 1.0.1 Build Type:
DATA + WPS + LDPE
Advertisement Version: 2
Duplex: half
Device ID:FRMA_BK2_WLCCS5508_01_100
System Name:
Interface address(es):
    IPv4 Address: 10.80.82.240
Platform: AIR-CT5508-K9, Capabilities: Host
Interface: Ethernet1/11, Port ID (outgoing port): GigabitEthernet0/0/2
Holdtime: 136 sec
Version:
Manufacturer's Name: Cisco Systems Inc. Product Name: Cisco Controller Product
Version: 7.0.240.0 RTOS Version: Erro Bootloader Version: 1.0.1 Build Type:
DATA + WPS + LDPE
Advertisement Version: 2
Duplex: full
FRMA_BK2_CSN5K_02# sh cdp neighbors interface ethernet 1/10 detail
Device ID:FRMA_BK2_WLCCS5508_01_100
System Name:
Interface address(es):
    IPv4 Address: 10.80.82.240
Platform: AIR-CT5508-K9, Capabilities: Host
Interface: Ethernet1/10, Port ID (outgoing port): GigabitEthernet0/0/1
Holdtime: 138 sec
Version:
Manufacturer's Name: Cisco Systems Inc. Product Name: Cisco Controller Product
Version: 7.0.240.0 RTOS Version: Erro Bootloader Version: 1.0.1 Build Type:
DATA + WPS + LDPE
Advertisement Version: 2
Duplex: full
From WLC Controller end
(Cisco Controller) >show port summary
           STP   Admin   Physical   Physical   Link   Link
Pr Type   Stat   Mode     Mode      Status   Status Trap     POE    SFPType
1 Normal Forw Enable Auto       1000 Full Up     Enable N/A     1000BaseTX
2 Normal Forw Enable Auto       1000 Full Up     Enable N/A     1000BaseTX
What might be the issue here?
Thanks for your suggstion

Hi Grant,
Thanks for your sugggestions.But however we Have 6 Controllers, all are having the same setup as this one.
Only difference i seen for this switch is for the th port 1/11 it is showling 2 CDP info, one for management interface of WLC and other for Logical interface of WLC, which seems not correct.
Ths CDP info connecting to Logical interface is showing half duplex and cdp info connecting to Physical interface of wlc is showing full duplex.
FRMA_BK2_CSN5K_02# sh cdp neighbors int eth 1/11 detail
Device ID:FRMA_BK2_WLCCS5508_01_100
System Name:
Interface address(es):
    IPv4 Address: 10.80.82.240
Platform: AIR-CT5508-K9, Capabilities: Host
Interface: Ethernet1/11, Port ID (outgoing port): LAGInterface0/3/1
Holdtime: 125 sec
Version:
Manufacturer's Name: Cisco Systems Inc. Product Name: Cisco Controller Product
Version: 7.0.240.0 RTOS Version: Erro Bootloader Version: 1.0.1 Build Type:
DATA + WPS + LDPE
Advertisement Version: 2
Duplex: half
Device ID:FRMA_BK2_WLCCS5508_01_100
System Name:
Interface address(es):
    IPv4 Address: 10.80.82.240
Platform: AIR-CT5508-K9, Capabilities: Host
Interface: Ethernet1/11, Port ID (outgoing port): GigabitEthernet0/0/2
Holdtime: 125 sec
Version:
Manufacturer's Name: Cisco Systems Inc. Product Name: Cisco Controller Product
Version: 7.0.240.0 RTOS Version: Erro Bootloader Version: 1.0.1 Build Type:
DATA + WPS + LDPE
Advertisement Version: 2
Duplex: full

WLC 5508 duplex mismatch error

Hi I've got a WLC 5508 connected to a Catalyst 6000 switch. In the switch I've get a CDP duplex mismatch error every 30 min.
%CDP-4-DUPLEXMISMATCH:Full/half duplex mismatch detected on port 3/23
with the show port command I can see this:
Port Name                 Status     Vlan       Duplex Speed       Type
3/23 WLC           connected trunk        full        1000 10/100/1000
With the show CDP neigh I see a duplex mismatch
C6K9> (enable) sh cdp neig 3/23 detail
Port (Our Port): 3/23
Holdtime: 142 sec
Capabilities: HOST
Version:
Manufacturer's Name: Cisco Systems Inc. Product Name: Cisco Controller Product Version: 7.0.116.0 RTOS Version: Erro Bootloader Version: 1.0.1 Build Type: DATA + WPS
Platform: AIR-CT5508-K9
Port-ID (Port on Neighbors's Device): GigabitEthernet0/0/1
VTP Management Domain: unknown
Native VLAN: unknown
Duplex: half (Mismatch)
But in the WLC console there is not half duplex
(WLC5508) show>port 1
           STP   Admin   Physical   Physical   Link   Link
Pr Type   Stat   Mode     Mode      Status   Status Trap     POE    SFPType
1 Normal Forw Enable Auto       1000 Full Up     Enable N/A     1000BaseTX
I don't have errors in the port counters
How I can resolve this duplex mismatch?

Try upgrading the firmware of the WLC to 7.0.230.0.

Duplex Mismatch when connecting ip phone with 2950 switch

When I connect my Cisco IP Phone 7960 with 2950 Switch (any access port within voice vlan), I get the message on Port duplex mismatch but the phone works properly.
From my switch the speed setting is 100/Full but from the Phone its Auto.
My Question is when I try to change duplex settings from Phone, it doesn't gives me any option instead only one option available to save so kindly someone tell me the best way to fix this from Phone or do I have to change the duplex from switch to AUTO ?

Thanks but When I connect with my Cisco 2950 Switch, I can see the weird kind of language as per my attachment.
It wasn't yesterday when I first configured from scratch but just seen today.
Switch is working good with Cisco IP phone connected with it.

Duplex mismatch on phone

Hi
Can someone explain the following to me please.All our ip phones are deployed with their settings pc/sw config as auto/auto. Desktops are all on 100fullmb as are the 3750 switch ports they connect to. Mostly all is fine but sometimes I get duplex mismatches on syslog server. When I change phone settings to 100full it resolves. How come this happens on some and not others.
Also what is best practice as we are deploying in other offices now; I would have though everything set to 100full.
Thanks ,
Frank

If you manually set a port to 100/full then plug in a device set to auto/auto that device will default to 100/half. If you set one device manually you have to set whatever it connects to manually as well. Best practice is to set everything to auto negotiate and that will result in 100/full. In your case you have all devices with a duplex mismatch and you should be having lots of performance and voice quallity issues.
Take a look at this link for details on how ethernet port speed and duplex negotiation works.
http://www.cisco.com/en/US/customer/products/hw/switches/ps700/products_tech_note09186a00800a7af0.shtml

XP vs W7 communications coping with duplex mismatch?!?

Whilst deploying a Windows 7 SP1 Pro Standard Operating Environment to one of our 60+ sites we were having some massive comms issues. The site is on a relatively slow (max 2Mbps link), but the difference in consistency between the former XP and
'new' W7 machines is striking
e.g. SOME W7 log in taking 40+mins (compared to XP based machine approx 2mins), RDP sessions from XP based machine fine compared to unusable from W7 machine, Lost SSL sessions on W7 machines compared to 'normal' functionality on XP machines, etc.
So, the fundamental issue appears to have been a duplex mismatch between the router (3rd party managed) and the sites 'core' switch.
However, we are struggling to understand why the W7 machines were so much more susceptible to issues compared to the XP machines... I understand that the TCP/IP stack was fundamentally rewritten between XP and Vista/W7, but can anyone point to anything that
would explain why the W7 machines exposed the issue so much more acutely?
I'd appreciate any thoughts or suggested areas of investigation?
Thanks
David

Hi,
Based on my experience, you may check the netmon traces or monitor the performan which is in the task manager.
Download Microsoft Network Monitor Tool from the following link and install it on the two machines.
http://www.microsoft.com/downloads/details.aspx?displaylang=en&FamilyID=983b941d-06cb-4658-b7f6-3088333d062f
Best regards,
Steven Song
Please remember to click “Mark as Answer” on the post that helps you, and to click “Unmark as Answer” if a marked post does not actually answer your question. This can be beneficial to other community members reading the thread.

Error message "auto duplexer is not installed" after a paper jam was removed on my epson artisan 837.

I print from a Macbook Pro (April '09) OSX 10.9.3 to an Epson Artisan 837 duplex all-in-one which has been functioning perfectly for some time. The other day while duplex printing I got a vague error message to the effect "printer error, turn off machine and power back on." I repeated that process several times waiting a period of time and/or doing it speedily. I even unplugged the printer from its outlet, turned off the computer, waited overnight and tried again, all to no avail. I then found the back tray had a paper jam which I removed and replaced the tray. Since this ordeal I have NOT been able to use the duplex function. After apple's air-print, an Epson Customer Service person told me to add a printer in Systems, printer preferences and to simply add in the same printer (only one i have) but choose not to have it be air-print. This worked even though it gave me Epson Artisan 837 and Epson Artisan 837II (the first with air-print the second not). I must be missing some step this time, however, because although I now have essentially 2 printer choices, the Epson II has duplex printing choices grayed out and gives me the error message "auto duplexer is not installed." Sorry to make this so long, but can anyone help me with this problem?

Thank you. Those are beautifully written procedures.
Looks like it's a network issue. I reach the step, "Adding a printer using the wizard":
You must enter the following URL, you must use the Queue Name you noted down earlier
http://<IP address of Mac>:631/printers/Queue Name
which I do, entering
http://192.168.0.4:631/printers/MP830
and I get the following error:
"Could not connect to the printer. You either entered a printer name that was incorrect or the specified printer is no longer connected to the server."
And then I am toast!
Using the other procedure, I simply don't see the Mac's printers in the Bonjour Wizard's "Browse for Bonjour Printers" window.
Not sure where to go from here -- any ideas?
The Mac's IP (set via DHCP) is 192.168.0.4, subnet mask 255.255.255.0. The PC is 192.168.0.5, I can't find the subnet mask.
Pretty sure it's a network config issue, especially isnce I can Bonjour to my other Mac.
TIA...

System Message "Linking primary sales accounts has not been completed"

When I try to enter an incoming Payment, I get System Message "Linking primary sales accounts has not been completed". What have I missed.
Banking -> Incoming Payments -> Incoming Payments
A System Message window pops up and the System Message Log window indicates it is an informational message with a message ID -1.
New System
Version: 88
PL: 14

Hi,
Welcome you to the forum.
I have moved your thread from admin to here. Your question belongs here.
Have you searched the forum? There are quite a few discussions for this topic. Such as this: Linking primary sales accounts has not been completed
Thanks,
Gordon

Purpose of Messages link in MI Client SP 18 ?

Hi,
Could anyone please tell me the purpose of Messages link in MI Client SP 18 ?
what is it for ? when and what kind of messages it contain ?
Currenlty when i am clicking on it , it is showing error page .
Thanks & Regards,
Vipin

Hi Vipin,
Adding to the points mentioned above.
This is for the system messeges, you receive from the middleware.
Purpose is to update the users with the latest information about the upgrades,timelines,system down times etc...
For ex: A system administrator can set the messeges( based on the users also )
to the users about the upgrades of the system and can ask not use the application until next updated messege comes about the upgration of the system(this is only one example)
Simply we can say that this messeges is used to inform the users about some information(critical).
Hope this is helpful.
Cheers,
Karthick

OT...forum program has a glitch re: Last message link?

Everytime I click on the Last (message) link at the bottom of a page I get kicked out to a page with all the various Adobe product forums listed. Is it just me or is this happening to others?
(Admins can delete this Subject if wanted)

It's a right Royal pain in the *** to have to load all the messages just to get to the latest one...especially when the thread is well over 100 messages long. Damn, is no-one looking at this?

Help, the "New message" link is missing!

We’ve received feedback from some forum members that they are sometimes unable to start a new thread.
They can access the boards, read posts and indeed reply to existing posts, but aren’t actually able to submit a new message.
This is due to how some posters access the boards.
When you click on a category from the forum main page, e.g the Broadband category, you get the option to select which board you want to go into. In this case, the options are:
ADSL/Copper Broadband Speed/Connection Issues
BT Infinity Speed/Connection Issues
Other Broadband Queries
If you select one of these boards, you will be able to see the “New Message” link (along with the posts within that board) and start a new thread.
If however you click on “View All”, at the bottom of the “Recent Topics” section, you’ll see a list of all of the posts in these boards, but you won’t be able to start a new message. This goes for all the other boards on the forum as well.
The screenshot below shows where these links are displayed, and where you need to go:
Thanks @AjayK48 for starting a thread about this issue.
Stephanie
BTCare Community Manager
If you like a post, or want to say thanks for a helpful answer, please click on the Ratings star on the left-hand side of the post. If someone answers your question correctly please let other members know by clicking on ’Mark as Accepted Solution’.

"I created the key CacheInquiryResuts under HKLM\Software\Microsoft\Microsoft DPM\Configuration
After that I putted a DWORD aka REG_DWORD called InquiryResultsTimeoutInterval into it and changed the value to 1 (hour)."
From Update Data source - Refreshing to clear cash is greyed out - DPM 2012 R2 UR5 (https://social.technet.microsoft.com/Forums/en-US/cb348256-7ed5-4d6b-a018-ea2a61d8fbad/update-data-source-refreshing-to-clear-cash-is-greyed-out-dpm-2012-r2-ur5?forum=dataprotectionmanager)
Have a nice day !!!
DPM 2012 R2: Remove Recovery Points

Add 'Send Message' link to table of connections taskflow

I need to add "Send message" link to table of connections taskflow (tableOfConnections-ListView.jsff).
Please suggest how can I access ProfileActions.addmessage action in tableOfConnections-ListView.jsff in order to add this link.

I tried a lot things and even consulted an oracle consultant but could not get this working. The message service was always sending the message to same user(first user you sent a message).
Finally We changed the user journey and removed the link from user list page.

Beginning this morning, Friday, May 27, Firefox will not open message links in Delphi Forums. Instead it wants me to download. IE is able to connect to the links.

I don't know what else to tell you. Firefox connects to Delphi successfully, but, when clicking on the "2 new" message link, I get a box asking me to choose the software to open the link. But the link is not a document, it is a link.

You're welcome
If it happens again then try to reload those web page(s) and bypass the cache or clear cache and cookies.
* Press and hold Shift and left-click the Reload button.
* Press "Ctrl + F5" or press "Ctrl + Shift + R" (Windows,Linux)
* Press "Cmd + Shift + R" (MAC)
Clear the cache and the cookies from sites that cause problems.
"Clear the Cache":
* Tools > Options > Advanced > Network > Offline Storage (Cache): "Clear Now"
"Remove the Cookies" from sites causing problems:
* Tools > Options > Privacy > Cookies: "Show Cookies"

Discrepancy message Link Duplex Mismatch

Similar Messages

Maybe you are looking for